Search Documents

By K. J. Reid, H. A. Lex, I. Iwasaki, K. A. Smith

The effects of autogenous grinding and conventional grinding on the floatabilities of copper-nickel sulfides from Duluth gabbro were investigated. At the same mesh-of-grind copper, nickel, and cobalt recoveries were higher and residual sulfur in the flotation tailings was lower with the autogenously ground pulps. With the ball-mill ground pulps the residual sulfur in the tailings could not be lowered to the level attained by the autogenously ground pulps even at increased levels of the collector addition. From mineralogical examinations of concentrate and tailings samples, an electrochemical interaction between grinding media and sulfide minerals was thought to have a greater effect on sulfide mineral flotation behavior than the breakage characteristics of the ore samples in these two types of mills.

Jan 1, 1984

By David Firewick, Daniel Stewart, Richard Rein

Panel caving of the Henderson orebody began in August, 1976. Fifty months later, on September 10, 1980, the cave zone appeared on surface as a steep-walled cavity positioned directly above the initial cave area. Although surface survey data revealed the development of a slight depression over the production area, surface inspection by geologists, three days prior to breach- ing, resulted in no evidence of impending glory-hole development. Geologic factors such as rock contacts and alteration-zone boundaries had little influence on the location of the initial glory hole. Since initial breakthrough, the glory-hole shape and growth have not directionally followed caveline advance because of topography and faulting. Based on periodic data, mine production has resulted in immediate growth of the Henderson glory hole.

Jan 1, 1984

W. H. BASSETT, * Waterbury, Conn.-Manganese should not be expected to remedy all the defects that are due to poor melting practice. It is undoubtedly valuable in helping to eliminate porosity in many of the alloys. In the copper-nickel alloys, its use is becoming almost universal, for, beside helping to make sound castings, it tends to hold the carbon in solution in the solidified alloy. GWILLIAM H. CLAMER,? Philadelphia, Pa.-I have found that manganese copper is satisfactory for eliminating sulfur and that it works very well in the crucible and when you have reducing conditions; but in a large reverberatory charge, where the conditions are oxidizing, we were not able to eliminate the sulfur.

Jan 1, 1919

By J. K. Gustafson

Since prehistoric times, gold has been sought for its beauty and its unusual physical and chemical properties. Early in the dawn of civilization it became the ultimate unit of value, and for at least 6000 years it has been used to barter for other commodities. It has been prospected for, treasured and made into works of art and personal adornment. From time to time, it has even been the object of conquest. Because of its predominant role as a basis for money in recent centuries, economists have come to think of gold solely in these terms. Gold, however, has physical and chemical properties that make it one of the most useful metals in the modern world. It is the most ductile metal known. An ounce of it can be drawn into a continuous wire over 35 miles long. It is also so malleable that an ounce of it can be beaten into films 0.00001 in. thick covering 68 sq ft of surface. It has a density of 19.3 and is so heavy that 1 cu ft of it weighs more than half a ton. Gold is nonmagnetic and has a high electric conductivity that is only slightly less than that of silver and copper. Gold is so inert to all the chemicals found in nature that gold coins and jewelry buried beneath the soil or at the bottom of the sea for thousands of years appear to be as bright and perfect as when they were first immersed. Finally, gold has an extremely high reflectivity of both light and infrared rays.

Jan 1, 1971

By P. Somasundaran, Yee-Ho Wang

Carrier flotation of anatase impurities from clay using oleate is compared in this study with conventional flotation. The role of relevant parameters such as carrier size, carrier amount, dissolved calcium and carbonate, conditioning speed, pH, time and temperature and collector concentration is investigated in order to elucidate the mechanisms involved in carrier flotation. Addition of coarse calcite particles is found to contribute towards the enhanced separation of anatase from clay mainly due to aggregation of anatase fines with calcite and the subsequent flotation of the aggregates.

Jan 1, 1980

By Stephen Krickovic

As it is commonly understood in the bituminous coal mining industry, pillaring means removal, as completely as is practical, of all pillars formed in the development of headings and rooms on first mining. The degree to which this can be accomplished, termed percent of recovery, is of course dependent generally upon the physical conditions of the bottom and the overburden, the system of min-

Jan 2, 1955

By P. G. Shewmon, J. Y. Choi

The surface-diffusion coefficient for , has been measured on (111) and (100) surfaces of copper from 1000" to 620°C. D,(Ge) on the (111) is two to three times that on the (100) as was found earlier for copper and gold on copper. D, (Ge) on both (111) and (100) is about thirty times that found for gold or copper tracers on the same surfaces, while in the temperature range where both D,(Ge) and Ds(Au) have been measured the activation energy for germanium is the same as that for gold. The apparent activation energy for Ds(Ge) is not a constant, but decreases with temperature. In a recent paper we reported on the application of a new tracer technique to the determination of the surface-diffusion coefficient (D,) for gold and copper on (111) and (100) surfaces of copper.' In this paper, we shall give the results obtained when the same technique was used to measure Ds for germanium on the (111) and (100) surfaces of copper. In addition to providing data on D., for an additional element on copper, the longer half-life of germanium (275 days) meant that Ds could be measured down to a much lower temperature and thus over a much wider temperature range (1000" to 620°C) than was used in our gold-tracer work (1060" to 780°C) or copper mass-transport studies (1060" to 800). The apparent activation energy for D, (Ge) is essentially the same as that found for gold or copper in the same temperature range, though the values of D, (Ge) are thirty times greater than those found for gold or copper tracers. The most interesting new result found is that the apparent activation energy for Ds(Ge), and thus Do, definitely increases with temperature. Such a trend was much more apparent in Gjostein's mass-transport work on copper than in our own, though in an earlier paper we mentioned the difficulty of fitting all of our points with one straight line:= No real explanation of this is given though experiments done on grain boundary groove growth at various ambient pressures demonstrate unequivocally that vapor transport plays no part in the increase in activation energy with temperature.

Jan 1, 1964

By William Kobbé

I. INTRODUCTION THE word recovery as used in this paper is applied in its broader sense and not limited to wells producing from horizons of unconsolidated sands. Certain problems connected with the winning of petroleum from such horizons present themselves while drilling is in progress and should be considered before drilling is commenced wherever unconsolidated sands are expected. Maximum recovery depends not alone upon efficient pumping methods but also upon the selection of a proper drilling system and the completion of a well especially adapted to the extraction of these oil-bearing sands. II. DRILLING DETERMINING FACTORS IN SELECTION OF METHOD The selection of a drilling method for the development of a region in which the oil reservoir consists of unconsolidated sands is based on the following considerations: (1) Character of the formations overlying the reservoir; (2) thickness of the oil-bearing stratum or strata; (3) thickness and character of water or gas sands; (4) gas pressure to be encountered or expected; (5) total depth of well.

Jan 12, 1916

By Graham MacFarlane

The largest area of high-grade cannel coals known in America is doubtless found in eastern Kentucky. Notwithstanding the popular belief to the contrary, there is no reason to doubt that these eastern Kentucky cannel-fields, following the general rule, will be uncertain and treacherous. But, taken in the aggregate, their extent is very great. The principal service to which cannel coal can be put is enriching illuminating-gas. The electric light has, to a certain extent, created a demand for better gas, and has increased the market for gas-enrichers. Before the discovery of rock-oil, coal-oil was distilled from cannel coal and cannel shale. This business was getting fairly started when the cheaper rock-oil, or petroleum, overcame it, and the great distilleries went into disuse and ruin. Now, again, the chief competitor with cannel coal is oil, namely, the cheap oil of Lima, Ohio. Under proper treatment the vile odor of this oil can be removed.

Jan 1, 1890

By J. O. Whiteley

IT is difficult to give a refining outline that may be followed for any and all combinations of the platinum metals; different combinations require different methods of attack. This paper does not pretend to go into all of the reactions of the metals of the platinum group, but will outline the commercial refining of platinum scrap. TYPICAL PLATINUM SCRAP As a concrete case, let us take 100 oz. of miscellaneous scrap, made up of jewelry scrap, dental scrap and laboratory ware. This lot will contain some platinum, palladium, iridium, ruthenium, rhodium, gold, silver and copper. The first problem is to get all of the metals in solution. If the scrap is principally platinum, palladium and gold, a treatment with aqua regia is the course to pursue; but if the scrap contains alloys high in iridium or ruthenium, aqua regia will act too slowly. In the case in hand, we are going to presume that we have scrap high in iridium and ruthenium, and proceed accordingly.

Jan 1, 1928

By Charles J. Haas

The effectiveness of rock bolts in resisting shear displacement along preexisting fracture surfaces or slip planes was determined in the laboratory with full-scale bolts and large-scale shear test equipment. The system variables were the type of bolt, orientation of bolt relative to shear surface, and normal pressure on the interface. Results showed that, in general, both conventional bolts and resin- grouted reinforcing bars significantly increase the shear resistance along a fracture or bedding plane when the average normal compressive stress on the plane is in the order of 25 psi and when the bolt is oriented such that it tends to lengthen as the shear progresses. An increase in shear resistance is also noted at the higher normal pressure of 250 psi; however, the increase is small compared to the corresponding shear resistance without a bolt. Conventional bolts oriented such that they lose tension as shear displacement occurs added no shear resistance since the tension drops to zero at very small shear displacements.

Jan 1, 1977

By J. O. Whitely

IT is difficult to give a refining outline that may be followed for any and all combinations of the platinum metals; different combinations require different methods of attack. This paper does not pretend to go into all of the reactions of the metals of the platinum group, but will outline the commercial refining of platinum scrap. TYPICAL PLATINUM SCRAP As a concrete case, let us take 100 oz. of miscellaneous scrap, made up of jewelry scrap, dental scrap and laboratory ware. This lot will contain some platinum, palladium, iridium, ruthenium, rhodium, gold, silver and copper. The first problem is to get all of the metals in solution. If the scrap is principally platinum, palladium and gold, a treatment with aqua regia is the course to pursue; but if the scrap contains alloys high in iridium or ruthenium, aqua regia will act too slowly. In the case in hand, we are going to presume that we have scrap high in iridium and ruthenium, and proceed accordingly.

Jan 1, 1928

Draftsman and transitman for coal mine work in Middle West. Salary $125 per month. No. 277. Technical graduate wanted for metallurgical work in experimental laboratory of large New England manufacturing concern. A knowledge of metallography of steel is essential. Practical experience is desirable but not required. No. 305. High-class man to install and take charge of a coal mining property. Must be experienced in handling labor and of good sound judgment. Work will require a man to be on the grounds practically all the time. The work is drift mining and is not gaseous. No. 306. Engineer familiar with the acid treatment and melting of cyanide precipitates; also a competent assayer. Applicant must be able to furnish good references. No. 307. Wanted-practical mining man, foreman, or superintendent for work in middle or southern Atlantic States. Salary $200 per month. No. 308.

Jan 5, 1918

By AIME AIME

T'HE Columbia Section of the A. 1. M. E. took charge of the Western Mining Convention on Oct. 3, and the meeting was held under their auspices. W. L. Zeigler, chairman of the Section, called the session to order. The first paper on the program, "Lead Refining Practice at Bunker Hill Smelter," was presented in per-son by the author, A. F. Beasley, superintendent of the smelter. He pointed out the differences in the refining practice at Bunker Hill from other American refineries. The Bunker Hill plant was the first to adopt the liquation process for silver skims as developed in Australia. Details were given of operating practice with results. F. F. Colcord questioned the author in regard to the kind of metal best suited for kettles, which was said to be cast iron.

Jan 1, 1929

By Jock A. Campbell

Oil-impregnated rocks are known to occur in 22 of the 50 states. The largest known petroleum resources of this type are in Utah, with over 95% of the inventoried total, The Utah deposits are estimated to contain over 25 million bbl (42 gal per bbl) of oil in place.' All major Utah tar sand deposits crop out and can be mined partially by open pit methods, but in-situ techniques will have to be employed to recover oil from the deeper parts of the deposits. No significant development of Utah tar sands deposits for their petroleum content has occurred to date, although a mine and extraction plant are anticipated this year at Asphalt Ridge. The barriers to development have been mainly economic, but technological and legal problems will also have to be overcome.

Jan 5, 1975

By Alan U. Seybolt

UNLIKE its sister elements, columbium (niobium) and tantalum, vanadium has not been available until recently in fabricated form. While Vanadium Corporation of America has offered the metal in fairly pure form for sale for many years in small lots for research purposes, this grade of vanadium has been brittle, probably because of a high oxygen content. Hence, when in 1950 the announcement1 was made that wrought vanadium was available as a commercial material, this represented a large step forward in the metallurgy of vanadium. While vanadium is generally regarded as a rare metal, data on its occurrence in the earth's crust show it to be as abundant as copper, zinc, and lead combined. Vanadium is widely distributed, but it does not seem to occur in massive deposits except in a few localities, principally in Colorado, Utah, and Arizona, where it is found in sandstone formations, and in Mina Ragra, Peru. Only in Colorado or Peru are ores mined solely for the vanadium content. Ores in the United States are principally carnotite and roscoelite; the former is of particular interest because of its uranium content. It is a uranium-potassium vanadate containing approximately 52 pct of UO2 and 18 pct of V2O5. Production in the United States during the war years averaged around 2000 tons a year, but dropped to 636 tons in 1946. In recent years, ferrovanadium has been selling for about $2.80 per pound of contained vanadium. This suggests that the price of the pure metal will never be as low as $2.80 per pound, but it could

Jan 1, 1953

By Allan Gibb

The ores of copper are usually associated with minerals containing arsenic, antimony and bismuth. Whatever the means adopted for extracting the copper, these metals are usually found, to a greater or less extent, in the product. There is, however, usually some elimination in the various metallurgical operations to which the ores are subjected, and some attempt is made here to determine the degree to which this elimination is effected.

Jan 1, 1903

By Henry S. Drinker

Few men reach middle life without having had the experience of failure in one or more undertakings; and most of us can look back with gratitude to help or advice given us by friends at critical periods of our lives. If, as men, we ask and take the benefit of such aid, why should we expect our eons to be stronger ? A parent can make no greater mistake than to send a boy, however steady and intelligent he may be, off to school or college, and expect the boy always to cope success-

Jan 1, 1911

By Eugene H. Cowles

The German silver industry of the United States amounts in value to upwards of $6,000,000 or $8,000,000 annually. Several thousands of people earn a livelihood pursuing it, and the beautiful goods and articles manufactured from this time-honored and valued alloy are everywhere visible. German silver enters largely into our street signs, harness and house hardware, and all manner of table-ware, solid or plated. There is scarcely an hour in the day that German or nickel-silver is not before our eyes. The composition of this alloy is a very uncertain thing, and depends largely on the honesty of the manufacturer and the price the purchaser is willing to pay. It is composed of copper, zinc and nickel in varying proportions. The best varieties contain from 18 to 25 per cent. of nickel, and from 20 to 30 per cent. of zinc, the remainder being copper. The more expensive nickel-silver contains from 25 to 33 per cent. of nickel, and from 75 to 66 per cent. of copper. The nickel is used as a whitening element; it also strengthens the alloy and renders it harder and more non-corrodible than the brass made without it, of copper and zinc. Moreover, it reduces the odor emanating from brass, which is so disagreeable if it occurs about the dining-table. Of all troublesome alloys to handle in the foundry or rollingmill, German silver is the worst. It is unmanageable and refractory at every step in its transition from the crude elements into rods, sheets or wire. As a white-headed furnace-man recently said to the writer, in one of our large mills, " you can put eight crucibles into the fire, each containing exactly the same mixture of German silver, and when you take them out and pour them into slabs for rolling, seven will be a mass of scum or slag, or the stuff will swell up like rising bread and overflow the moulds, and be so full of blow-holes that it will look like a sponge. The eighth crucible will contain perfectly good metal. On remelting the next day, the bad stuff will, in nine chances out of ten, come out just as good metal as the eighth pot the day before, and under apparently the same conditions." With nickel at seventy or eighty cents per pound, German silver

Jan 1, 1890

The Institute's stock of Volumes XXXI, LI, and LII has become much reduced by sales: If members have copies of these volumes which they can spare, the price of $3 per volume will be paid for them, if in good condition. If desired, a copy of the Index for Volumes XXXVI to LV will he given for one of these volumes of the Transactions and one dollar additional. For two volumes of the Transactions, a copy of the Index will be sent and the balance will be credited to the payment of clues.

Jan 12, 1918