Search Documents

By J. R. Long, T. R. Graham, C. W. Matthews, R. S. Dean

In a previous paper! the authors reported on the mechanical properties of a 65 per cent copper, 10 per cent manganese, 25 per cent zinc alloy as compared with, similarly processed cartridge brass. Additional investigations by these laboratories, on higher copper alloys, have demonstrated that at lower zinc concentrations even larger amounts of pure manganese may be added to copper-zinc alloys without exceeding the single-phase solid solution limits, and that similar increases in tensile strength, yield strength, and hardness may be obtained without excessive decreases in ductility. Several compositions in this range showed also a decided color change with increasing manganese. The normal "brassy" color was considerably lightcncd and reduced to a faint yellow cast at 15 per cent manganese. With higher manganese contents the alloys were essentially white and similar in appearance to the nickel-silver alloys. From this work it appeared that it would be desirable to determine more completely the properties of the wrought and annealed white alloys. Accordingly, a more detailed study was planned of an alloy having the composition 70 per cent copper, 20 per cent manganese, and 10 per cent zinc. This alloy remained single-phase throughout the working and annealing cycles of the preliminary tests and appeared to be' about the strongest of the white single-phase alloys. The project included also an investigation of additional alloys, deviating from this composition by 5 per cent of each of the three components to evaluate the effects of variation in composition and a study of the propertics of the central alloy made with silicothermic manganese. Material Preparation Electrolytic manganese, wirebar copper, and electrolytic zinc were used for the preparation of the alloys. Representative analysis of the electrolytic manganese seldom exceeds 0.01 per cent iron, 0.02 per cent sulphur and 0.02 per cent lead, with no silicon or aluminum. A typical sample of the silicothermic manganese metal contained 2 per cent iron, 0.81 per cent silicon, 0.16 per cent carbon, and 0.36 per cent aluminum. Melting and alloying were performed in a high-frequency furnace with magnesia crucibles. Melts were deoxidized with small aluminum additions and cast into 25-lb. slab ingots. Care was exercised in deoxidation to avoid excessive amounts of residual aluminum, which has been found to have significant effects on alloys in this system. All ingots were hot-rolled at 1200' to I300°F. and then cold-rolled with intermediate anneal-

Jan 1, 1945

By S. W. Parr, F. B. Hobart

Studies relating to the behavior of coal toward oxygen may have for their purpose the determination of the fundamental factors that underlie spontaneous combustion, weathering and deterioration, and the general topic of storage, as well as those properties that have to do with the underlying principles of carbonization. There is also involved the possibility of developing information relating to the constitution of coal, or at least the chemical properties inherent in the type substances of which the coal is composed. It is the purpose here to record certain results bearing on this latter idea of the chemical properties that characterize the main constituents of bituminous coal. The avidity of freshly mined coal for oxygen has long been known. What happens to the coal or to the oxygen is not so clear. Is the oxygen absorbed or chemically combined, and what are the conditions as to time, temperature, texture, or components that are most involved in the phenomenon? If we subject a weighed quantity of coal maintained at a constant temperature to a current of oxygen, we may obtain three factors of interest—the weight increase of the coal, the weight of the water, and the weight of the carbon dioxide formed in the reactions involved at that

Jan 1, 1925

By Stephen Taber

Introduction.............................. 62 Asbestiform Minerals.......................... 63 Chemical and Mineralogical Relations............... 63 Physical Properties........................ 64 Types of Asbestos............................ 65 Origin of the Fibrous Structure...................... 66 Views of Previous Investigators.................... 66 Discussion of the Evidence.................... 67 Conclusions........................... 69 Origin of Cross-fiber Veins....................... 71 Chrysotile Veins......................... 72 Structural Features of Cross-fiber Veins............... 78 Veins of Crocidolite and Other Fibrous Amphiboles........... 83 Origin of Slip-fiber........................... 84 Origin of Mass-fiber........................... 86 Discussion............................... 87 IntRoduCtion The term asbestos, as commonly used, includes half a dozen minerals all having a well-developed fibrous structure, but differing in chemical composition and in some of their physical properties. In its strict application the name is limited to the fibrous varieties of the monoclinic amphiboles. Commercially, however, the most important of the asbestiform minerals is chrysotile, a fibrous variety of serpentine. About 95 per cent. of the asbestos used in manufacturing is chrysotile, and it commands a much higher price than any of the other fibrous minerals now on the market. Although the production of asbestos has increased rapidly in recent years, comparatively little has been published concerning its origin. The present paper is preliminary in its nature, and therefore does not pretend to exhaust the subject. The ideas herein developed are the result of field investigation, laboratory experiments in the growth of fibrous

Jan 1, 1918

By D. J. Barrett, M. A. Sochocky

INTRODUCTION Summary of Factors Influencing Comminution Circuit Design The selection of an appropriate comminution circuit for a specific ore is one of the most important decisions in the design of a processing plant. The importance is related to the fact that the capital and operating costs for crushing and grinding plant generally represent, as is well known, the major portion of the plant costs. This chapter will, therefore, identify as many as possible of the factors which influence the selection of a comminution circuit. The number of factors which will have to be considered for any comminution project will depend, among other things, on the type of project. If, for example, the project is an entirely new mining development, then most, if not all, the factors identified will have to be analyzed. If the project is an expansion of a developed mining operation or if the new orebody is adjacent to a viable operation, then the existing operation will influence the choice of factors or design constraints which need to be considered. The existing infrastructure or supporting systems may be quite adequate to accommodate the requirements of any expansion or new development. Hence, those factors may not have to be considered. To cover, however, the widest spectrum of projects, the factors which have been identified in this chapter are those which will have to be considered for the most complex of projects, that of developing an entirely new mining operation. The range of factors is as broad as the range of different ore types. Thus, each development must be treated with individualized care. The most important step in the development is the analysis and understanding of the ore characteristics. The hardness of the ore, its abrasiveness, friability, moisture content, grade, mineralization including gangue mineralization, liberation size, chemistry, and other characteristics should be the first to be analyzed in the investigation. The next should be the determination of factors such as plant size, throughput, location, climate, accessibility, and availability of water. The selection of samples for initial bench scale work and bulk sampling (when needed) for further

Jan 1, 1982

ALTHOUGH everybody is familiar with coal, few persons have an exact idea of, the great impor-tance of this precious fuel. Coal is the black bread of industry. Without it, industrial activity is much restrained; and so the great industrial countries of Europe and the United States of America are the great producers of coal. The 1913 production of coal in Belgium was 22,842,-000 tons, valued at 418,700,000 fr., nearly a half billion. In 1919, it was 18,483,000 tons, about 81 per cent. of the production before the war; in 1920, it had reached 22,414,000 tons, approximately the production before the war. To show the importance of coal production of Belgium, let us say that the coal industry employed 168,000 workers in the year of 1920, the metallurgical industry only 129,000 and the textile industry 103,000. The coal industry, then, employs the greatest number of workers. The value of the coal production in 1919 is estimated at 1,121,000,000 fr. On the basis of the production before the war, the value of the production of iron in 1919 would have been 701,000,000, of finished steel 1,086,000,000, and of zinc 415,000,000; therefore, in 1919 the value of the coal industry was greater than that of the metallurgical production.

Jan 8, 1922

All the TECHNICAL PUBLICATIONS and CONTRIBUTIONS published in 1935 are available at Institute headquarters, unless otherwise noted. They are also on file in many public, university and technical libraries and, when so indicated in the list, may be found in the TRANSACTIONS. Copies of the TECHNICAL PUBLICATIONS have been mailed to members of the Institute that are registered in the different classes: A-Metal Mining; B-Milling and Concentration; C-Iron and Steel Division; D-Nonferrous Metallurgy; E-Institute of Metals Division; F-Coal Division; G-Petroleum Division; H-Industrial Minerals Division (Nonmetallics); I-Mining Geology; J-Mineral Industry Education Division; K-Mining Administration; I-Geophysical Prospecting. Other members may obtain copies by writing to the Secretary. Copies of CONTRIBUTIONS may also be obtained from the Secretary's office. Additional copies are sold at the rate of 1 cent per page; minimum charge, 25 cents. Nonmembers may purchase the papers at the prices mentioned. [ ]

Jan 1, 1936

By Carl Swartz

METALLURGISTS differ considerably in their opinions regarding the effect, if any, of small amounts of iron pyrites, or other iron compounds on zinc sulfide ores during the roasting operation. As a result, the literature on this subject expresses many conflicting ideas. The ore, previously crushed to pass through a one-millimeter screen, dries in the roasting kiln, losing water up to 200° to 300° C. At 150° C. iron pyrites begin to lose sulfur. As the temperature increases, while the ore is passing to the hotter part of the furnace, the sulfur burns to sulfur dioxide, leaving the metals as zinc oxide and ferric oxide. These two substances then interact to form zinc ferrite, a compound, yellow brown in, color, having the general characteristics of a spinet Like magnetite, another spinel, zinc ferrite is insoluble in alkalis and dilute acids. As a result, when leached with 10 per cent. sulfuric acid solution zinc values tied up in this compound remain behind. HISTORY In the electrolytic recovery of zinc from its ores, the roasted ores are usually leached with a 10 per cent. sulfuric acid solution. When the zinc ore contains iron pyrites as an impurity in an appreciable amount, the actual yield of metallic zinc is much lower than a theoretical calculation would indicate. Further, losses of zinc are, in a rough way, directly proportional to the amount of iron pyrites or other iron compounds present. When the iron is present in the ore in an isomorphous relation to the zinc, as in the case of a marmatite, a greater amount of zinc remains insoluble than when present as a true pyrite or marcasite. Work on the insoluble residues obtained from leaching of the calcines shows that the zinc lost is intimately tied up in this residue. Some investigators have suggested a definite compound, such as zinc ferrite, others merely a mixture of zinc and iron compounds.

Jan 1, 1927

By M. F. Trice

Pyrophyllite is a hydrous aluminum silicate (A1²Si4O10(OH)²)1 that, occurs in both the foliated and the massive forms. The foliated variety resembles talc in that it has a greasy feel, a pearly luster, perfect basal cleavage, and usually is white, although in some deposits apple green, gray, brown, russet, and nearly black specimens may be found. The massive deposits of pyrophyllite yield pearl gray to light tan aggregates, some of which are so friable that they may be crushed with the hands into a fine gritty powder. Frequently specimens of the massive variety are studded with crystals of radial structure. The mineral has a specific gravity of about 2.7 and a hardness of 1 on Mohs' scale.' The chemical composition of commercial pyrophyllite reflects the mineralogy of the deposits, which, according to Stuckey12 contain pyrophyllite and quartz, together with chloritoid, sericite, and a few other minerals of negligible importance. The latter, he says, ('are noticed in but small quantities to the extent they might occur as accessory constituents of an igneous rock or as products of regional metamorphism or weathering. . . . Quartz is abundant everywhere except in the very best grades of pyrophyllite." Analyses of specimens from several deposits are listed in Table 1, showing that the silica content varies from 57 to 73 per cent and the alumina from 22 to 33 per cent. Oxides of iron and the alkaline metals are collectively present, with one exception, to an extent of about 1 to 1.5 per cent. Sources At present, North Carolina is the only commercial source of pyrophyllite, although the mineral has been found in small quantities in many parts of the world. The North Carolina deposits are in the "Carolina Slate Belt," which traverses the center of the state in a southwesterly direction. This belt varies from 8 to 50 miles in width. Two major deposits of pyrophyllite lie along its eastern boundary, in what is known as the Deep

Jan 1, 1942

By M. F. Trice

Pyrophyllite is a hydrous aluminum silicate (A1²Si4O10(OH)²)1 that, occurs in both the foliated and the massive forms. The foliated variety resembles talc in that it has a greasy feel, a pearly luster, perfect basal cleavage, and usually is white, although in some deposits apple green, gray, brown, russet, and nearly black specimens may be found. The massive deposits of pyrophyllite yield pearl gray to light tan aggregates, some of which are so friable that they may be crushed with the hands into a fine gritty powder. Frequently specimens of the massive variety are studded with crystals of radial structure. The mineral has a specific gravity of about 2.7 and a hardness of 1 on Mohs' scale.' The chemical composition of commercial pyrophyllite reflects the mineralogy of the deposits, which, according to Stuckey12 contain pyrophyllite and quartz, together with chloritoid, sericite, and a few other minerals of negligible importance. The latter, he says, ('are noticed in but small quantities to the extent they might occur as accessory constituents of an igneous rock or as products of regional metamorphism or weathering. . . . Quartz is abundant everywhere except in the very best grades of pyrophyllite." Analyses of specimens from several deposits are listed in Table 1, showing that the silica content varies from 57 to 73 per cent and the alumina from 22 to 33 per cent. Oxides of iron and the alkaline metals are collectively present, with one exception, to an extent of about 1 to 1.5 per cent. Sources At present, North Carolina is the only commercial source of pyrophyllite, although the mineral has been found in small quantities in many parts of the world. The North Carolina deposits are in the "Carolina Slate Belt," which traverses the center of the state in a southwesterly direction. This belt varies from 8 to 50 miles in width. Two major deposits of pyrophyllite lie along its eastern boundary, in what is known as the Deep

Jan 1, 1942

By Robert W. Thomas

During the past 20 years the advantages of reinforced concrete as a substitute for timbering in so-called permanent mine openings have been fully recognized, and its use has become almost general practice in the larger mines. The term "permanent mine openings" is used advisedly and is assumed to embrace such openings as ventilation shafts, material shafts and main hoisting shafts, with their adjacent stations, ore pockets, etc. In the concreting of such openings, the actual cost as compared with that of timbering has been of secondary consideration, the support of large openings, elimination of fire hazards, and prevention of interruptions to production being the primary objectives. The ultimate economy, however, of lining such openings with concrete when they are to remain in use during the entire life of the mine, and especially when they are in bad ground, will seldom be questioned. During this 20-year period there have appeared in engineering publications a number of interesting articles on the use of concrete in mines, nearly always describing some specific project of major proportions, such as the concreting of ore pockets, large stations or main hoisting shafts. Such articles are unquestionably of interest, since the projects require considerable engineering thought, not only in the method of excavating large openings, but in their engineering design as well. Concreting of main hoisting shafts, particularly when this is done with the least possible interruption to production, provides some interesting problems. The concreting of haulage drifts of the dimensions commonly found in mines, on the other hand, soon develops into a routine operation, therefore it is with some hesitancy that the author attempts to prepare an article on this subject. The writer can recall only one article on the concreting of mine haulageways, although several articles have been written concerning the concreting of tunnels considerably larger in dimensions than those required in general mine practice.' From the scarcity of articles on the subject, it would seem that the concreting of haulage drifts is still far from being considered general

Jan 1, 1937

By H. J. Denning, M. W. Brabbins, A. K. Isaac

The quality of a coalface floor is the essential element that enables powered supports to generate their designed loads in control of coalface strata. The paper introduces a technique for the appraisal of coalface foundation stability. A criterion of support efficiency, viz., the support pressure increase/strata convergence, is included in case study data obtained from investigations in the South Wales Coalfield, U.K.

Jan 1, 1984

By Paul I. Eimon, Byron R. Berger

INTRODUCTION Epithermal silver-gold deposits form at low to moderate temperatures in near-surface environments. These deposits are found in all rock types, but historically, the most important deposits occur as veins in volcanic rocks (e.g., Creede, Colorado; Pachuca, Mexico) and as replacements in sedimentary sequences (e.g., Mercur, Utah; Carlin, Nevada). Increases in the open-market prices for silver and gold in the last few years have resulted in renewed interest in precious metals and the economic viability of large-tonnage low-grade deposits. These bulk-mineable deposits form as replacements in permeable horizons or as stockworks in the up- per parts of otherwise bonanza-type hydrothermal systems and newly recognized systems that erupted onto the surface as hot springs, fumaroles, or geysers. Large tonnage low-grade de- posits were an unconventional resource prior to price increases; however, now they constitute one of the main sources of precious metals in the United States and the importance is growing worldwide. This paper presents conceptual geologic- geochemical models of epithermal precious-metal deposits derived from studies of productive deposits throughout the world. Much of the data presented is not new. However, the interpretation of the data in terms of current concepts of hydrothermal processes is new. This paper deals with idealized and general ore-forming mechanisms, and no attempt is made either to explain the origin of the different chemistries of ore- forming fluids or to examine all of the variations in specific deposits due to local structural controls and host-rock compositions.

Jan 1, 1983

By Granville S. Borden

This brief is a reconnaissance report on some prospects in the field of taxation which can safeguard our Mineral Resources. The brief is a prospectus soliciting help and enthusiastic cooperation in the common task of developing these prospects in a manner which will be most beneficial to all parties-the owners, operators, employees, tradesmen, the federal and state governments, and the people of this nation.

Jan 4, 1950

By W. Irwin Moyer

Two methods for the rapid valuation of oil properties are in common use. The one best known and most widely used is the "per barrel" value, based on the present daily production of the well, without regard to its past performance or the history of the sand or pool from which it produces. The second method is the "time to pay out," or the length of time required for a well to place itself upon the credit side of the ledger, from which time the returns from its production (less the operating expenses) will be clear profit. The time basis for valuation is also commonly used in the appraisal of an undeveloped lease. In most oil fields, it is not thought good business to invest in production that will not pay out in at least 4 to 5 years. Nearly all buyers (except in certain regions of very persistent production like the deep-sand territory of the Appalachian field) expect wells to pay out in considerably less time than this. Like the barrel per day price, the time necessary for a well to pay out has been determined for each field, so that one frequently hears a field or district referred to as having a certain time to pay out. This is considered the norm for that field or district and the buyer and seller base their value, to greater or less extent, on their belief in the accuracy of this time. The writer long ago became convinced of the inaccuracy of the barrel per day method, except when greatly modified for local conditions, such as the age of the wells, their economic limit, operating conditions in the field, the future price of oil, and the persistence of the sand as a producer. When so modified, this method becomes more of an analytic or predicted probable yield valuation. While the appraiser may not go through each step in a valuation based on future returnable revenue, his knowledge of the field and the local conditions surrounding his leases make it possible for him to estimate a fair sales value that, in many cases, will be a close approximation to the truth. This is quite different from the commonly understood barrel per day value, in that the conditions surrounding the sale of one lease or property at a fair market value may

Jan 1, 1922

(Under this heading will be published notes sent to the Secretary of the Institute of members or other persons introduced by members) Young mining engineer, and geologist, member, technical, graduate with four years' varied mining experience in the West and Southwest as miner, surveyor and engineer. Past 18 months, work in mine geology, mapping and examinations. Would prefer assisting consulting engineer or work with exploration company in foreign service. Unmarried. Age, 28. No. 331. Member; aged 35, married, with 10 years' experience in the Southwest, thoroughly competent to take full charge of mining and milling operations. Particularly fitted to handle either gold or tungsten producers. At liberty February 1. Will go anywhere. No. 340. A member wants a roving commission to examine old mines of the Mother Lode in. California, especially those which can be bought for their taxes. Some of these mines are reported to contain large quantities of low-grade ores which can now be treated at a profit. No. 341.

Jan 2, 1917

By F. Milton Lewis, Roshan B. Bhappu, James L. Coburn

FOREWORD-To comminute is to pulverize, but, in mining technology, "comminution" includes all the multiple crushing and grinding operations on ore, rocks, coal, and certain other bulk materials. The primary objective of this two-part article series is to provide the reader with basic information and guidelines for designing comminution systems. Part One is confined to ore processing operations, where size reduction is required to liberate the valuable minerals so that they may be concentrated and recovered. Part Two will illustrate various design techniques through practical examples.

Jan 9, 1976

By J. A. Clum, R. W. Heins, T. D. Tiemann

The use of Na-montmorillonite clay binders (Western Bentonite) in the pelletizing of iron ore concentrates is well established as is the idea that alternative binders must be found. 1-6 This note summarizes work done7 in evaluating a Wisconsin montmorillonite clay binder. The clay occurs in irregualr beds overlying the Prairie du Chien Dolomite and the St. Peters Sandstone near Hersey, St. Croix County.

Jan 1, 1978

E. W. King, Bozeman, Mont.: The form of measuring up ore in sight looks very plausible, as illustrated in the paper of Mr. Emmons, but from my experience of many years of mining in Montana and Nevada, I have found it is very hard to measure up anything nearer than a guess of what you have in sight, except in the case of a true vein, or a flat vein where the boundaries are well defined. I have been interested in several miues with Dr. A. R. Ledoux, and I know that my foreman and myself, going into the mines and using our best judgment, could seldom see more than 30 days' supply actually in sight, and yet we were running from 100 to 250 tons a day, and keeping it up year after year. Prof. John D. Irving, New Haven, Conn.: I understand from Mr. Emmons that this is a method which has been found applicable in the copper-mines in Tennessee, where the record could be made with a good deal of accuracy, and where the work in the mines allowed the necessary development to be done, so that the record could be kept up. I do not think there was any intention in his mind to imply that this was applicable to all cases, especially such as Mr. King has mentioned. President Charles Kirchhoff, New York, N. Y. : I think the point is that the paper impresses the necessity for doing it where the possibilities exist. There has been too little attention given to this very matter, particularly in the United States; but I think our English friends are following it very much more zealously, and the demand for it there is possibly greater than it is here, because English boards of directors handle mines that are often very much further away than our own are, and the English public and the English engineers generally are very much more insistent upon seeing how much longer current dividends are going to last, or current assessments are going to continue.

Jan 1, 1913

By J. F. Wolff

CARL ZAPFFE, Brainerd, Minn. (communication to the Secretary*).¬Unless one has actually directed explorations for iron ore, it is doubtful whether the importance of Mr. Wolff's paper, the value of the information contained, and the large amount of detail work involved in what is set forth can be fully appreciated. It is indeed rare to get such a com-

Jan 3, 1917

By H. J. Struth

Conditions in the gasoline market undoubtedly influence the oil industry's general economic situation to a greater degree than perhaps any other single factor. No matter how efficiently the oil industry manages to conduct its producing operations, a drop in the price of gasoline exerts definite pressure upon the posted price of crude oil in the field. Efforts of the recent past have shown that profits from the producing division of the industry are closely tied in with the course of the gasoline market. When refinery gasoline prices are depressed, as they have been during recent months, it is utterly impossible for purchasers to maintain a crude market that is commensurate with the cost of production, regardless of how well balanced the producing situation may be. In fact, the producer can no longer regard his operations in the light of an independent unit of the oil industry, since his financial well-being is directly dependent upon the well-being of the refiner. Because gasoline is the principal constituent of crude oil, it is obvious that profitable refining operations can only be maintained through profitable gasoline markets. Likewise, when the price of gasoline influences a profit for the refinery it also influences the prosperity of the producer, through the advent of higher and more profitable posted prices for crude oil in the field. Financial results for 1932 showed material improvement over the preceding year, primarily because the price of gasoline was maintained at levels somewhat above those of 1931. Consequently, the producer was able to record improvement in the crude market, through a somewhat higher level of posted prices. While effective methods of prora-t,ion of crude production are given credit for the advance recorded in the crude market last year, it is also a fact that the advent of higher prices for gasoline had a direct influence upon the posted prices of crude oil. For example, when gasoline was sold in Group 3 at 2 3/4 a gallon in June and July, 1931, the price of 36-gravity Mid-Continent crude was down to its lowest point of only 18c a barrel. As refinery prices advanced, however, there was a corresponding advance in posted prices of crude oil. Thus, when Group 3 gasoline commanded a price of 5c a gallon

Jan 1, 1933