Search Documents

By E. E. Russell Tratman

The use of dynamite in cold weather is attended with some difficulty, owing to the freezing of the material and its consequeut liability to fail to explode when the fuse is fired. With proper methods and care the dynamite can be thawed with reasonable safety, but numerous accidents occur (more than get reported in the public press), due to carelessness in the operation and to the treacherous nature of the material, or a combination of both conditions. Dynamite will stand treatment at one time which at another time will result in explosion. An expert on explosives says that the most dangerous means of thawing cartridges are ingeniously devised by ignorant laborers; baking, boiling and toasting being favorite methods, while at a stone-quarry, in one instance, an apparatus was arranged for steaming the cartridges over a pot of boiling water. In this latter case the nitro-glycerine leaked through the canvas cover and settled on the bottom of the pot, with the result that an explosion occurred, the water acting as a tamping to the charge. The fact that small quantities of explosives containing nitroglycerine will burn quietly and without explosion if ignited by direct contact with a flame, has led to the dangerously mistaken reasoning that merely heating the explosive can produce no ill effect. If . a dynamite cartridge is ignited or placed in a fire it will probably burn harmlessly away, but if placed on a stove or in an oven and

Jan 1, 1893

The earliest U. S. patent on a crushing machine was issued in 1830. The device incorporated the drop hammer principle later used in the famous stamp mill, whose history is so intimately linked with that of the golden age of American Mining. Eli Blake invented the first successful mechanical rock-breaker --the Blake jaw crusher--patented in 1858. The idea of his mechanical principle, the powerful-toggle linkage, was so sound that today the Blake -type jaw crusher is the standard by which all jaw crushers are judged. In 1881, Philetus Gates was granted a patent on a machine which included in its design all the essential features of the modern gyra tory crusher. For some years after these pioneer machines were developed, crushing requirements were quite simple. All underground mining and open-pit quarrying was done by hand with tonnages and rock sizes generally small. In the milling of precious metal ores, stamp mills were popular as the final reduction machine. The stamps were fed with an ore size readily produced by one break through small gyratory or jaw crushers. Even in large underground mining operations, there was no demand for large crushers; and increasing tonnage requirements were met by duplicating the small units. The Homestake gold mine in South Dakota was a good example, where in 19 15 twenty -two small Gates gyratory crushers were used to prepare the ore for the batteries of 2,500 stamps. Open pit mines and the introduction of the steam shovel created a demand for larger crushers, which led to the development of a gyratory with an 18 in. (457 mm) receiving opening. Up to this time, the jaw crusher had kept pace with the gyratory, both from the standpoint of receiving opening and capacity; but now the gyratory stepped into a 15-year lead with larger and larger sizes. This trend toward large primary crushers started just before the turn of the century, and in 1910 crushers with 48 in. (1.22 m) receiving openings were being built. About this time, the jaw crusher was revived in a great contribution to primary crushing by the introduction of the 84 in. by 60 in. (2. 13 by 1. 52 m) machine. This crusher was usually followed by a 24 in. (6 10 mm) opening gyratory crusher for secondary breakage, a system which reawakened the industry to the use of the jaw crusher as a primary breaker. It is interesting that although his machines never came into general use, Thomas A. Edison ranks as a pioneer in the development of the large primary breaker. Edis on reasoned that the recoverable electrical energy

Jan 1, 1978

By W. J. Sharwood

(San Francisco Meeting, September, 1915) CUPELLATION is well known to be one of the most effective methods of separating silver and gold from base metals and other impurities, as well as one of the most accurate means for their estimation. In the latter application it consists in absorbing in some porous medium the fused lead. oxide formed by the oxidation of the lead "bath," which carries with it the oxides of other base metals present. It has long been recognized that small amounts of both silver and gold were removed and absorbed together with the base metals, as well as being to some slight extent volatilized, and in work of the highest accuracy a correction is made for the "cupellation loss." Thus. in the assay of bullion this is done by means of "proofs" of like composition, which are manipulated throughout in precisely the same manner as the assay pieces, and are assumed to lose or gain like amounts. In the case of certain very rich ores and commercial products the loss is adjusted by assaying the cupel itself and recovering the precious metal absorbed, but this doubles the labor and does not remedy the loss by volatilization. Arbitrary tables have been drawn up by various authorities with the object of enabling a correction to be applied without the use of a check. These have been of very limited practical use owing to the fact that a number of factors affect the losses sustained. For a fixed amount of precious metal the loss varies with the amount of lead used, with the nature and amount of the impurities, with the porosity of the cupel, with the air supply, and above all with the temperature at which cupellation is carried on. Pure silver loses relatively much more than gold, but the loss in either is diminished by au addition of the other metal. The concentration of precious metal in the litharge increases as the concentration in the lead increases, but little work has been published connecting the two. If all other conditions remain the same the actual total loss increases, but the percentage loss diminishes, with an increase in the weight of precious metal treated.

Jan 8, 1915

By W. A. Forbes

by the combustion of this gas as it reached the air was a familiar sight in the days when open-top furnaces were in vogue. As blast-furnace practice progressed, however, involving the use of hot blast and the development of power from the gas, blast-furnace construction was modified to conserve this gas for heating hot-blast stoves, raising steam under boilers, and various miscellaneous purposes. When the use of blast-furnace gas was extended to the driving of gas engines, the necessity for thoroughly cleaning the gas became apparent., and soon the advantages of also properly cleaning the gas for use in stoves and udder boilers became more fully recognized.

Jan 10, 1913

By C. E. Ells, A. Sawatzky

The effect of neutron irradiation on tensile properties of the Zr-2.5 wt pet Nb-0.5 wt pet Cu alloy has been evaluated for integrated neutron fluxes up to 3 x 1020 n per sq cm (E > 1 Mev). Specimen temperature during irradiation was normally 300°C. The material was studied both in annealed and in quenched and aged conditions. When the alloy (fab-ricatedfrom sponge zirconium) is quenched from a temperature =40°C below the a + ß/ß transformation and aged 6 hr at 535oC, neutron irradiation up to the maximum studied has little effect 071 reduction in area, although there is a drop in uniform elongation and the yield strength is increased by = 25 pct. Conversely, irradiation of the alloy in an annealed condition can result in much greater changes in properties, with yield-strength increases of up to 200 pet. The dose dependence of irradiation hardening obeys the saturation equntion proposed by Makin and Minter to explain hardening in copper and nickel: Act = C[1 - exp(-Døt)/1/2 A rnodel is proposed to explain the effect of niobium content and metallurgical condition on irradiatiotz behavior. THE Zr-Nb alloys form a class of material susceptible to marked strengthening by quench and age heat treatment. With niobium concentrations as low as 2.5 wt pet, strengths can be developed which are double those of annealed zircaloy-2.1 Since the neutron-capture cross section of the Zr-2.5 wt pet Nb alloy is nearly identical to that of Zircaloy-2, significant gains in power-reactor neutron economy could be obtained by replacing stressed in-reactor components of Zircaloy-2 with the heat-treated Zr-Nb alloy. When the solution heat-treatment temperature is in the high (a + ß) phase, then the tensile properties of the quenched (and aged at 500°C) material have been shown to be relatively insensitive to neutron irradiation.1-3 Addition of small quantities of copper to the binary Zr-2.5 wt pet Nb alloy gives a useful reduction to the corrosion rate in air and carbon di- oxide,&apos; and a ternary alloy of composition Zr-2.5 wt pet Nb-0.5 wt pet Cu was chosen for one component in the Douglas Point Reactor. This application utilizes both the corrosion resistance to a moist air-carbon dioxide environment and the strength developed by a quench and age heat treatment. By suitable choice of solution heat treatment and aging temperatures, tensile properties of the ternary alloy can be made nearly identical to those considered as optimum for the binary alloy. One effect of the copper addition, however, is to give marked changes in the aging kinetics of the alloy.&apos; For this reason, it appeared that neutron irradiation might promote overaging in the ternary alloy, particularly at the elevated service temperature (=300°C). This paper describes the effect of neutron irradiation on the tensile behavior of the Zr-2.5 wt pet Nb-0.5 wt pet Cu alloy in several metallurgical conditions pertinent to its use as a reactor material. The metallurgical conditions included those for which aging occurs in the unirradiated material, and fully annealed conditions for which a higher degree of thermal stability could be expected. 1) EXPERIMENTAL Two batches of alloy were used, both made from sponge zirconium. The fabricator&apos;s analysis of principle constituents showed no significant difference between the two batches, Table I. The rod material was rolled to 1.5 in. diam, and then swaged to final sizes of 0.5 to 0.375 in. diam at nominal temperatures of 785" and 625°C for the AM and AS batches, respectively. Subsequent hydrogen analyses at CRNL confirmed that the hydrogen concentration of the as-received rod was indeed <20 ppm. However, it was found that the (a + ß)/ß transus for the AM material was approximately 25°C lower than that of the AS material, indicating rather more difference in oxygen concentration than given in Table I. Except for a small difference in yield-point behavior, the tensile prop-

Jan 1, 1965

By R. L. Whiting, H. J. Ramey

The basic study from which this paper was prepared was started as the result of the growing need throughout the world for increasing quantities of energy in all forms. Quite obviously, natural forms of energy that are readily available at low development cost are those in greatest demand. The underdeveloped countries — and particularly those having little or no petroleum resources — are the countries in which the most interest is being shown in the newer energy sources. One of the least expensive energy sources is natural geothermal steam.&apos;-* Although this form of energy has been recognized for centuries, it has been only during the past 20 years that serious efforts have been made to harness it. Natural geothermal steam energy in Italy, New Zealand, Mexico, Japan, and California is now being produced through wells to drive turbines and generate electricity. Further, active exploration for natural geothermal steam is being conducted in Hawaii, Fiji, Taiwan, Chile, Russia, Greece, and Katanga. It is surprising to find that most geothermal steam exploration is in the "steam seep" stage. That is, surface studies are made and exploratory wells are drilled in the general area of steam seeps. However, in the larger geothermal steam areas, there have been efforts to apply the most modern geological and reservoir engineering principles in order to define the reservoir parameters, particularly those relating to estimates of reserves and future productivity. This paper is concerned with the development of appropriate equations and techniques to facilitate these estimates. Production of natural steam or hot water presents problems different from those experienced in the production of oil and gas. For example, steam or hot water systems may be essentially single-component systems, while hydrocarbon systems are most frequently multicomponent fluid systems. Heat effects are much larger for water than for hydrocarbon systems; and the natural steam production may or may not be isothermal, while production of petroleum reservoirs is considered normally to be isothermal. Petroleum reservoir engineering principles may be applied to natural steam or hot water reservoirs if the inherent differences in the systems are considered. The basic considerations involved in geothermal steam reservoir engineering are: thermodynamics, physical and thermal properties of water, materials and energy balances, fluid influx, and performance matching and predicting. Thermodynamics Fig. 1 is a pressure-temperature diagram for the liquid-vapor region for pure water, showing the critical point and five other points representing possible initial conditions for a geothermal steam reservoir. To generate a physical appreciation for the mechanics of natural steam production, it is helpful to consider

Jan 1, 1970

Edward Eeller, Baltimore, Md. (communication to the Secretary): Mr. Miller&apos;s improved method of the cyanide-assay for copper will, without doubt, be much appreciated by assayers and chemists who are engaged at copper mines and works. The writer, as one who, at one time, had much work of that kind to do, entertains no doubt of its practical value. In enumerating the factors which affect the accuracy of cyanide-titration, Mr. Miller omits to mention time. This I have always considered an essential one; i.e., in order to secure accuracy, I have believed it to be necessary to run the cyanidesolution at the same rate of speed in standardizing as in the titration of the samples. I have accomplished this, without the use of a time-keeper and without noticing the volume of the solution, in the following simple manner: In running the cyanide-solution from the burette, the stream was so regulated, by manipulation of the cock, that it retained its continuity for a distance of about one inch below the orifice, and, below that, broke into individual drops. This means that a constant pressure is maintained at the orifice of the burette, so that, during equal intervals of time, equal volumes of the solution pass through. The stream of cyanide-solution was left to flow in the manner indicated until the blue ammoniacal copper-solution began to show a distinct change in color, after which the cyanide was added by drops at regular intervals until the desired end-reaction. When several burettes are used they should have orifices of equal diameter; otherwise, the timefactor must be considered separately for each. In accordance with Mr. Miller&apos;s views, I have always considered the cyanide-method as of very satisfactory accuracy for all copper-assaying in which I did not employ the electrolytic method. It may interest some of my colleagues to know the modified method which I employed some fifteen years ago in making great numbers of copper-estimations on ores and

Jan 1, 1902

By W. A. Nagel, R. P. Alger, H. Sherman, J. Tittmann

A sidewall epithermal neutron tool has been developed to substantially reduce environmental effects that have previously complicated neutron log interpretation. Designed for operation in uncased wells, the device provides increased accuracy in both liquid-filled and empty holes. A brief discussion of neutron moderation, diffusion and capture shows that logs using epithermal neutron detection depend on a smaller number of formation-characterizing parameters than those using thermal neutron or capture gamma ray detection. Thus, they come closer to providing an unambiguorls determination of hydrogen content. In this new device a directionally sensitive epithertnal neutron detection system has been incorporated in a side-wall source-detector skid to minimize borehole effects. The effects of variations in borehole size and shape, mud type, temperature and salinity are greatly reduced. Small residual borehole effects are then computationally accounted for in the surface control panel to provide a borehole-corrected neutron log. The log presents a direct recording of neutron-derived porosity on a linear scale. With corrections for borehole effects already applied, this direct recording of porosity simplifies log interpretation. Furthermore, comparison with a linear porosity presentation of a formation density log permits sandstones, limestones and dolomites to be readily identified. Thus, in complex or variable lithology, porosity is determined with greater accuracy and reliability than heretofore. Laboratory data and field results demonstrate the improvements in neutron logging afforded by this new side-wall epithermal neutron logging device. INTRODUCTION The new Sidewall Neutron Porosity (SNP) logging system, designed for use in uncased wells, provides reliability and accuracy never before achieved with neutron logs. The effects of variations in borehole diameter and shape, fluid salinity, mud weight and temperature—parameters that have long complicated neutron log interpretation— are suppressed or corrected for by this sidewall epithermal neutron detection system. Furthermore, to simplify interpretation the SNP log presents a direct recording of computed porosity on a linear scale. The performance improvements achieved by this new system arise primarily from the combination of two im- portant design features. First. though not unique to this new tool, an epithermal neutron detection system is used,&apos;,&apos; Epithermal neutron detection substantially reduces the perturbing influences of the thermal neutron absorption properties of rock matrices and water salinity. Second, the neutron detection system is mounted in a directionally sensitive sidewall skid to greatly minimize borehole effects. The purpose of this paper is to explain briefy the advantages offered by the detection of epithermal neutrons, to describe the SNP equipment and the log, to present calibration and correction data and to give examples of interpretation methods made especially convenient by this new system. ADVANTAGES OF EPITHERMAL NEUTRON DETECTION Epithermal neutron detection, of all the neutron methods in current commercial use, provides the simplest determination of formation hydrogen content. Advantages of epithermal neutron detectors, as compared with thermal neutron and gamma ray detectors, are probably best explained by a brief review of the life of a source-emitted neutron. A fast neutron from the source will eventually be cap-tured by the nucleus of an atom. However. before capture is likely to occur, the fast neutron (energy of 100,000 electron volts (ev) or more) will be slowed down until it is in thermal equilibrium with its surroundings. The neutron is then considered to be a "thermal" neutron (average energy of 0.025 ev at 25C). The overwhelming majority of the slowing down thus occurs in reaching epithermal energies (energies just above thermal—0.5 to several ev). After reaching thermal energy. the neutron will "diffuse" through the formation with, on the average, no further energy change until capture. Upon the capture of the thermal neutron, relatively high energy gamma rays arc usually emitted. Hydrogen plays a very important role in the process of slowing down fast neutrons. On the other hand, the absorption effects of water salinity and low concentrations of other strong thermal neutron absorbers—relatively unimportant in the moderation process-—are very important in thermal diffusion, capture and the production of gamma rays. Thus, by detecting only epithermal neutrons with the SNP, spurious effects due to these thermal neutron absorbers are greatly minimized as compared to the effects on tools using thermal neutron or gamma ray detectors. The epithermal neutron detection system affords another important advantage. Log response in various litho-

Jan 1, 1967

By Fred D. DeVaney

MINNESOTA taconites are extremely hard, and fine grinding is required to produce an acceptable concentrate. To reduce grinding costs, waste material is rejected by magnetic separators as soon as it is liberated. Cyclones are now used in all Minnesota taconite plants to close the grinding circuits. Erie Mining Co. installed its first grinding section at Aurora, Minn., in 1948-a 9 ½ x12-ft. mill and a fine grinding section consisting of a 10 ½ x12-ft ball mill in closed circuit with a duplex 60-in. spiral classifier. Concentrates from the magnetic cobbers treating the rod mill discharge passed directly into the classifier; the ball mill discharge was also treated in magnetic separators and the concentrate from these machines also went to the spiral classifier. Both concentrates passed through ac demagnetizing coils. It is axiomatic that for proper classification the material in suspension must be well dispersed, and it follows that magnetic concentrate must be almost completely depolarized if classification is to be successful.

Jan 8, 1957

By T. M. Drown, P. W. Shimer

The precipitation of phosphoric with titanic acid, by boiling an iron solution which had been reduced to the ferrous condition by sulpharetted hydrogen or sulphurous acid, was first noticed by E. H. Bogardus in 1874.* Since that time, as far as we are aware, not much has been published on the relation of these two acids to each other, and to silicic acid, in the ordinary course of analysis of iron ores. The following investigation may perhaps aid in clewing up some of the obscure points in the analysis of titaniferous ores. THE DETERMINATION OF PHOSPHORUS. From two to five grams of the finely powdered ore are weighed into a beaker and treated with about 50 c.c. of hydrochloric acid (sp. gr. 1.12), evaporated to dryness, and heated ih an air-bath for

Jan 1, 1882

By Mark J. Klein, Robert A. Haggins

The pesence of a small amount of oxygen was found to cause significant grain growth restraint in 99.99 pct Ag. This behavior does not seem to be due to the presence of an oxide dispersion, but instead, to be related to the existence of minute amounts of oxygen m solid solution. In the amounts necessary to cause the observed effects it was found that oxygen migrates with extreme rapidity, probably along extended structural imperfections, such as dislocations and grain boundaries. A number of years ago, hastton&apos; observed that the presence of small amounts of oxygen caused a retardation of grain growth in silver. He attributed this behavior to the formation of a fine dispersion of oxide particles by the internal oxidation of trace impurities. More recently, wood2 also found that oxygen caused grain growth restraint in copper. Experiments using both copper and a dilute solution of aluminum in copper led to the conclusion that the effects observed in copper were due to oxygen in solid solution, rather than an oxide dispersion. During the course of a study of the influence of several solutes on the recrystallization of Silver, the presence of minute amounts of oxygen was found to exert a very significant influence on grain growth. The experiments reported here were undertaken to determine whether the grain growth restraint observed in silver due to the presence of oxygen is related to oxygen in solution or to an oxide dispersion. Because of the difficulty in measurement and control of the very small oxygen concentrations causing the observed effects no attempt was made to treat the data in a quantitative manner. EXPERIMENTAL PROCEDURE AND RESULTS Silver of 99.99 pct purity was melted and cast into slabs in a vacuum of better than 0.1 p. These slabs were reduced 50 pct by cold rolling to a thickness of approximately 2.5 mm. Samples cut from this material were annealed in vacuum for a series of different times at 803°C. Another group of samples was similarly annealed in air. This temperature is well above the recrystallization range for silver of this purity (150" to 200°C). The mean grain diameter of these samples was measured, both in the center and near the edge, using the line-intel-cept method, and is shown as a function of annealing time in Fig. 1. The grain size in the centers of the samples annealed in air was found to be larger than that of the surface regions, while the grain growth behavior of the edge and center regions annealed in a vacuum was approximately the same. he edge measurements were taken at a distance of 0.2 mm from the surface.) A few samples were annealed in nitrogen. Their behavior was identical to that of the vacuum-annealed samples. Samples annealed in oxygen had approximately the same grain growth behavior as those annealed in air, leading to the conclusion that this behaviouer is due to oxygen. The microstructure of a sample annealed in air at 803" for. 30 minutes is shown in Fig. 2. The smaller grain size near the surface is characteristic of the iir-annealed specimens. Possible causes of this grain growth restraint in the air-annealed specimen are the formation of an im-

Jan 1, 1962

By J. P. Neumann, L. Raymond

At temperatures near 1000°C, only the (112) (111) slip systems are operatire in tungsten. Therefore, the substructure introduced into the billet upon rleforming a single crystal by rolling at 1000 "C can be controlled by proper selection 01. processing ral&apos;iubles. Using a reduction of 10 pct pel- pass, the (001)[110] and the (110)[001] crystals will deform by duplex slip rip to a 50 pet reduction in thickuess. These rolled single-crystal sheels are characlerized by anisotropic hardening, retention of ductility with warm working, lattice bending which is related to the conlacl (angle, and macroscopic dimensional changecs in the length bid not the width of the billet. When several slip systems become operative, a greater degree of work hardening is itztvoducetl into the crystal. This rolling- condition is characlerized by isotropic hardening, loss of ductilily with warm working, complex lattice distortions, and macro-scopic dimensional changes in both the length rind Width of the billel. IN tungsten, the {1 10}(111) slip systems are operative below room temperature,&apos; while above 700°C only the {112{ (111) slip systems are observed.2,3 In the transition region, i.e., room temperature. both systems appear. It is the purpose of this investigation to show that tungsten single crystals deformed by rolling at a temperature where only one slip system is operative generate dislocation substructure which depends on the crystal orientation. For a specific crystal orientation. the resulting dislocation substructure can be further influenced by modifying the rolling procedure. Crystals oriented for multiple slip display less substructural sensi- tivity to modifications in processing techniques than do single crystals oriented for duplex slip. Under simple slip modes of deformation, very little work hardening is introduced into a rolled single-crystal sheet. Mechanical properties such as room-temperature strength. ductility, and hardness are used to confirm the existence of the different work-hardened conditions generated within the crystal by modified warm-rolling techniques. EXPERIMENTAL PROCEDURE Material. Single-crystal billets of four different crystal orientations. grown by the Arc-Verneuil technique. were ground to a size of 0.25 by 0.375 by 3 in. In terms of their rolling plane and rolling direction, the billets had the following orientations: (1101 [001 ] (110) [110] (001) [110] (001) [100] The actual orientation of all crystals was within 5 deg of the ideal orientations. The typical impurity content of the crystals is given in Table I. Polishing and Etching. Polishing was done elec-trolytically in a 20 g per liter aqueous solution of NaOH at approximately 10 v. It was established by the Laue back-reflection X-ray technique that the surface damage due to grinding and cutting operations with a diamond wheel did not exceed 0.001 in. Therefore after each cutting or grinding operation at least 0.002 in. was removed electrolytically from the surface in order to eliminate surface effects. By lowering the voltage to 3 v, subgrain boundaries and individual dislocations are identified in agreement with Berlec 4 where the etch-pit traces on a cubic plane form a square. The etching time was about 5 sec at room temperature. Rolling. Rolling was carried out on a Loma 2-high mill (Model 600). The peripheral velocity of the 6-in.-diameter rolls was 500 in. per min, with the surface temperature of the rolls about 400° to 450° C The billets were heated before each pass for 30 min in argon to 1000 C. Oxidation of the crystals during rolling in air resulted in a thin layer of greenish-yellow WO 3 This oxide was removed after each pass by immersing the crystals for a few minutes in a boiling NaOH solution. Prior to the initial rolling pass, a surface layer of 0.001 in. was removed by polishing. The crystals were then annealed in vacuum (10-4 torr) at 2400 C for 30 min. All crystals were rolled in the same direction; i.e., the same end was always introduced into the rolls. The rolling program was conducted in

Jan 1, 1965

By Graham Bright

The rapid increase in reliability, the low cost of operation, the ready application of safety devices, and the growing availability of central-station power have made the question of installing a hoist of the electric type no longer debatable. Where adequate electric power is available, there are few cases where it would be advisable to install a steam or air hoist. The type of electrical equipment depends largely on the nature of the power supply, its capacity, and the form of the power contract under which power is purchased. In a large majority of cases, the available electric power is alternating current, three phase, 60 cycles. There is, however, considerable 25-cycle power in use; and in a few instances constant voltage direct current is the only power available for a small or an occasional medium-size hoist. Where a new hoist is to be installed, the designer of the mechanical parts can readily take care of the maximum stresses likely to be imposed by the motor. Where the hoist is already installed and operated by steam or air and it is desired to substitute an electric motor for the engine, a careful check should be made to determine the advisability of using the old mechanical parts. In most cases it is better to install a complete new hoist than to attempt to use old mechanical parts. A steam engine has a definite maximum torque, which the hoist has been designed to withstand, while a motor may be able to deliver momentary torques beyond the strength of the mechanical parts of the hoist. The selection of the proper type of electrical equipment can only be made after complete information is obtained and certain calculations made to determine the capacities required. There are several methods used in making hoist calculations, but no matter what method is utilized a fair degree of familiarity with hoists and hoisting conditions is necessary before an intelligent analysis and proper selection can be made. Forms Used in Hoisting Calculations Some of the hoist calculation methods are long and complicated. Where such calculations are seldom made, it is better to use the

Jan 1, 1922

By Lawrence F. Schubert

Instrumentation is not a stranger to the minerals processing industry. In fact, very few plants now exist that haven&apos;t to one extent or another adapted operations to instrumentation. But with the rapid growth of such controls has come the need for effective departments composed of men trained to maintain and repair the instruments; here is where many firms fall short. The importance of the role an instrument department should play is underscored by the omnipotent effects which instruments often exert over an operation. Reserve Mining Co. is an example: while instrumentation at this taconite plant represents approximately 2% of the process equipment cost, a breakdown of instruments may result in the ineffective use (or complete shut-down) of the other 98% of plant investment.

Jan 7, 1966

Jan 1, 1968

By B. W. Frazier

Jan 1, 1882

By J. B. Davis

This paper has been prepared at the suggestion of Mr. Dunbar D. Scott, to supplement his " Evolution of Mine-Surveying Instruments."† Before entering into a detailed history of solar instruments, a few remarks will be made touching upon land-surveys in general, and on what has led to the development of these instruments.The oxidation of metals melted in contact with air takes place with dissimilar results. Tin, lead or zinc are examples of a class, the oxides of which float on the surface of the melted metal. First a film is produced, which covers the surface; then, if agitation from any cause exposes new metal to the action of the air, additional oxidation takes place, and the film is increased in volume. This change goes on until a considerable quantity of oxide (or " dross," as it is technically called) is formed; depending, of course, upon the duration of the exposure of the metal to the atmosphere. When such metals are poured, the dross may be skimmed off; and clean metal will be left underneath. The removal of such oxides is, therefore, merely a mechanical process. In the case of copper, however, the result is quite different. The sub-oxide of copper (Cu2O) is readily soluble in molten copper; and therefore, instead of the formation of a film of oxide, to be finally removed as dross, the surface of the metal remains bright and clear, because the oxide has been dissolved as soon as it was produced. It is customary in the process of copper-refining to leave a small quantity of oxide in the metal, in order to oxidize any traces of bismuth, arsenic or antimony which have not been entirely removed. As a result, these metals exist in the commercial product as oxides, and not as metals, which would form an

Jan 1, 1901

By H. Kazemi

An ideal theoretical model of a naturally fractured reservoir with a uniform fracture distribution, motivated by an earlier model by Warren and Root, has been developed. This model consists of a finite circular reservoir with a centrally located well and two distinct porous regions, referred to as matrix and fracture, respectively. The matrix has high storage, but low flow capacity; the fracture has low storage, but high flow capacity. The flow in the entire reservoir is unsteady state. The results of this study are compared with the results of the earlier models, and it has been concluded that major conclusions of Warren and Root are quite substantial. Furthermore, an attempt has been made to study critically other analytical methods reported in the literature. In general, it may be concluded that the analysis of a naturally fractured reservoir from pressure transient data relies considerably on the degree and the type of heterogeneity of the system; the testing procedure and test facilities are sometimes as important. Nevertheless, under favorable conditions, one should be able to calculate in-situ characteristics of the matrix-fracture system, such as pore-volume ratio, over-all capacity of the formation, total storage capacity of the porous matrix, and some measure of matrix permeability. INTRODUCTION The analysis of flow and buildup tests for obtaining in-situ characteristics of oil and gas reservoirs has received considerable attention in the past decade. Most of the available techniques result in reliable conclusions in macroscopically homogeneous reservoirs or in the homogeneous reservoirs with only certain types of induced and/or inherent heterogeneity (such as wellbore damage, etc.). In general, the greater the degree of heterogeneity, the less the reliability of the information deduced from the pressure transient data. A commonly encountered heterogeneous system is a naturally fractured reservoir where two types of distinct porosities occur in the same formation. The region containing finer pores may have high storage and low flow capacities. This is called the matrix. The remaining region may have high flow capacity with low storage. The latter region is generally the set of interconnecting fractures and fissures of the rock, and for this reason it is called the fracture. Ordinarily, we wish to obtain the permeability and porosity of each region and perhaps the frequency of the fracture distribution in a reservoir. Such information is necessary for reservoir engineering. Other information, such as wellbore damage, will be useful in evaluating possible remedial work for such fields. Few authors have suggested theories to aid in calculating the in-situ characteristics of a naturally fractured reservoir similar to what we have described above. Pollardl suggested that a naturally fractured reservoir contained three distinct regions: a damaged or an improved region surrounding the wellbore, and the two remaining regions the same as described earlier. He suggested that the flow was taking place from the tight matrix into the highly conductive fractures, then into the we wllbore region and finally into the well column. He concluded that the average pressure buildup in each of these distinct regions can be expressed approximately in terms of an exponential decay function of time. He also hypothesized that the decay coefficients for each of these functions were significantly different from each other; consequently, each of these functions became dominant in turn, in the process of pressure buildup. Thus, by a proper graphic plot of the logarithm of wellbore pressure differences vs buildup time, each of these functions could be determined (see Fig. 1). Pollard suggested methods of determining the wellbore damage and fracture volume. Later Pirson and Pirson2 extended

Jan 1, 1970

By J. WILLIAM WETTER

WHEN the privilege was extended to me to address this meeting I could not help but make a mental review of my own activities and experiences in connection with association work. After having spent about 16 years in the mining engineering field, I entered into the operating branch of coal mining which afforded, about 12 years ago, my first opportunity of attending a meeting of our local Association and sitting in with the "big boys" of the industry. This was quite a thrilling experience because I had heard a great deal about the various operators who belonged to the Association and knew, or at least thought I knew, that a certain group dominated its affairs and that a "clique" was in control of a sizable "roller" which could be "steamed up" at will to flatten out any opposition which might appear upon the horizon or under it, too, for that matter. Now, I was to have the privilege of observing this "clique" at first hand, of seeing a small group making the policies and shaping the destinies of a great industry and planning the activities of an important Association while a large majority of the members would sit by either complacently or otherwise with the full knowledge that the "roller" was in waiting to reduce them to ribbons at the first sign of resistance.

Jan 1, 1930

By David Kellogg

THE electrodeposition of iron has been practiced for many years. The earlier work along this line was directed toward the preparation of pure metal, but later applications were the production of thin adherent coatings as used in the electrotyping of Russian banknotes in 1860. A historical discussion of this subject, however, would require too much space and would be inconclusive. Much has been written on the subject but no two experimenters use the same methods or materials. During the war, the British army repair, shops developed a method for building up worn parts of automotive machinery, aero engines, etc., using the cold surfate . bath and low-current density method.1 The method has been used successfully in commercial work for the production of about 6000 repaired parts, therefore experiments along the same lines have since been made at the Westinghouse research laboratory. The apparatus used was essentially that described in the article mentioned except that the current -used for cleaning was obtained from a 3/4-kw. 60-volt, house-lighting generator, direct connected to a 2-h.p., 870-r.p.m., 440-volt, three-phase, type CS induction motor; while the plating current was taken from the storage batteries at any desired voltage. The anodes were made from 0.036 in. (0.9 mm.) Armco iron made into cylinders 5 in. (127 mm.) long by 8 in. (203 mm.) in diameter with a disk of 1/8 -in. (3.17 mm.) micarta, having a 2 in. hole in the center fitted at each end of the cylinder for stirring. The anodes were hung on a wooden rocker frame driven by a wooden connecting I rod directly connected to a small reducing gear, such as is sold by most of the apparatus supply firms; 3 gal. stoneware crocks were used as containers. The solution used by Thomas, 75 gm. of the crystallized ferrous ammonium sulfate per liter, was tried, using the current density recommended by him; namely, 0.33 amp. per sq. dm. Under these conditions the deposit on a ½ -in.

Jan 2, 1922