Search Documents

By Graham Bright

The rapid increase in reliability, the low cost of operation, the ready application of safety devices, and the growing availability of central-station power have made the question of installing a hoist of the electric type no longer debatable. Where adequate electric power is available, there are few cases where it would be advisable to install a steam or air hoist. The type of electrical equipment depends largely on the nature of the power supply, its capacity, and the form of the power contract under which power is purchased. In a large majority of cases, the available electric power is alternating current, three phase, 60 cycles. There is, however, considerable 25-cycle power in use; and in a few instances constant voltage direct current is the only power available for a small or an occasional medium-size hoist. Where a new hoist is to be installed, the designer of the mechanical parts can readily take care of the maximum stresses likely to be imposed by the motor. Where the hoist is already installed and operated by steam or air and it is desired to substitute an electric motor for the engine, a careful check should be made to determine the advisability of using the old mechanical parts. In most cases it is better to install a complete new hoist than to attempt to use old mechanical parts. A steam engine has a definite maximum torque, which the hoist has been designed to withstand, while a motor may be able to deliver momentary torques beyond the strength of the mechanical parts of the hoist. The selection of the proper type of electrical equipment can only be made after complete information is obtained and certain calculations made to determine the capacities required. There are several methods used in making hoist calculations, but no matter what method is utilized a fair degree of familiarity with hoists and hoisting conditions is necessary before an intelligent analysis and proper selection can be made. Forms Used in Hoisting Calculations Some of the hoist calculation methods are long and complicated. Where such calculations are seldom made, it is better to use the

Jan 1, 1922

By Lawrence F. Schubert

Instrumentation is not a stranger to the minerals processing industry. In fact, very few plants now exist that haven't to one extent or another adapted operations to instrumentation. But with the rapid growth of such controls has come the need for effective departments composed of men trained to maintain and repair the instruments; here is where many firms fall short. The importance of the role an instrument department should play is underscored by the omnipotent effects which instruments often exert over an operation. Reserve Mining Co. is an example: while instrumentation at this taconite plant represents approximately 2% of the process equipment cost, a breakdown of instruments may result in the ineffective use (or complete shut-down) of the other 98% of plant investment.

Jan 7, 1966

By J. B. Davis

This paper has been prepared at the suggestion of Mr. Dunbar D. Scott, to supplement his " Evolution of Mine-Surveying Instruments."† Before entering into a detailed history of solar instruments, a few remarks will be made touching upon land-surveys in general, and on what has led to the development of these instruments.The oxidation of metals melted in contact with air takes place with dissimilar results. Tin, lead or zinc are examples of a class, the oxides of which float on the surface of the melted metal. First a film is produced, which covers the surface; then, if agitation from any cause exposes new metal to the action of the air, additional oxidation takes place, and the film is increased in volume. This change goes on until a considerable quantity of oxide (or " dross," as it is technically called) is formed; depending, of course, upon the duration of the exposure of the metal to the atmosphere. When such metals are poured, the dross may be skimmed off; and clean metal will be left underneath. The removal of such oxides is, therefore, merely a mechanical process. In the case of copper, however, the result is quite different. The sub-oxide of copper (Cu2O) is readily soluble in molten copper; and therefore, instead of the formation of a film of oxide, to be finally removed as dross, the surface of the metal remains bright and clear, because the oxide has been dissolved as soon as it was produced. It is customary in the process of copper-refining to leave a small quantity of oxide in the metal, in order to oxidize any traces of bismuth, arsenic or antimony which have not been entirely removed. As a result, these metals exist in the commercial product as oxides, and not as metals, which would form an

Jan 1, 1901

By J. WILLIAM WETTER

WHEN the privilege was extended to me to address this meeting I could not help but make a mental review of my own activities and experiences in connection with association work. After having spent about 16 years in the mining engineering field, I entered into the operating branch of coal mining which afforded, about 12 years ago, my first opportunity of attending a meeting of our local Association and sitting in with the "big boys" of the industry. This was quite a thrilling experience because I had heard a great deal about the various operators who belonged to the Association and knew, or at least thought I knew, that a certain group dominated its affairs and that a "clique" was in control of a sizable "roller" which could be "steamed up" at will to flatten out any opposition which might appear upon the horizon or under it, too, for that matter. Now, I was to have the privilege of observing this "clique" at first hand, of seeing a small group making the policies and shaping the destinies of a great industry and planning the activities of an important Association while a large majority of the members would sit by either complacently or otherwise with the full knowledge that the "roller" was in waiting to reduce them to ribbons at the first sign of resistance.

Jan 1, 1930

By R. J. Colony

The failure, or disintegration, of concrete in structures, even when the cement, sand, and coarse aggregate used have passed satisfactorily all tests and inspections, is not uncommon. Such failures occur even when proper methods of mixing and placing have been used and where weather conditions were correct. In these cases, the origin of the trouble must be sought in the cement; therefore some additional mode of determining the quality of cement must be employed. The problem is to find a simple, usable, easily applied method that will supplement the standard tests. The solution of this problem involves a knowledge of the chemical composition of Portland cements, also of their constitution (or componental composition), as the behavior of a cement, when gaged, is dependent on the physical and chemical characters of the compounds of which it is composed, the proportions existing between them, and the fineness of grinding. It is likewise essential to know the character, behavior, and composition of the hydration products of Portland cement. The most promising method of attack makes use of chemical, mechanical, and petrographic methods. Chemical, by determining quantitatively not only the usual constituents, but the carbon dioxide and water. Mechanical, by determining the fineness with the air analyzer,' which separates into fractions of various grain dimensions all of that portion which in the ordinary sieve test passes the 200-mesh sieve and constitutes at least 75 per cent. of the total cement. These fractions may be further studied chemically and petrographically and micrometric measurements can be made of the grains. Petrographic, by the method of immersion, and by making thin sections from test pats of both neat cements and standard mortars. Normal Portland cement is composed of mechanical mixtures of definite chemical compounds having constant chemical and physical properties. In the order of their cementing qualities these are: Tri-

Jan 1, 1922

By E. J. Roberts

F. C. Bond (Allis-Chalmers Mfg. Corp., Milwaukee) —This paper considers comminution as a first order process, with the reduction rate depending directly upon the amount of oversize material present. The data show that other factors should be taken into account, and it is possible that in time these may be evaluated as simultaneous or consecutive reactions: Development of the theory of comminution has been retarded for many years by the assumption that surface area measurements constitute the sine qua non of the work done in crushing and grinding, and it is encouraging to note the belated growth of other ideas. In the Abstract the term "net power" should be changed to "net energy." Throughout the paper the term "hp per ton" should be changed to "hp hrs per ton", or "hp hr t." The term "Probability Theory" in the title does not seem appropriate, since it is not clear how the probability theory is used in developing the ideas in the paper. There seems to be a contradiction between the large calculated advantages of closed circuit operation and the statement following that the closed circuit test results showed no significant change in grinding behavior, when compared with the batch grind curves. Tables I and II show that between 75 pct and 50 pct solids the energy input required decreases with increasing moisture content and may indicate the advisability of grinding at higher dilutions in certain cases. The calculation of the hp-hr per ton factor indicates an input in the laboratory mill of only 7.32 gross hp per ton of balls; this casts some doubt upon the accuracy of the factor used, since the power input in commercial mills at 80 pct critical speed is customarily much higher. The tests show that within fairly wide limits the amount of ore in the laboratory mill may be varied and a product of constant fineness obtained, provided that the grinding time is varied in the same proportion. This has often been assumed, and confirmation by actual testing is of value. The Cavg corrections for differences between the plant and laboratory size distributions do not seem very satisfactory, since in many cases the plant/laboratory ratio is farther from unity after correction than before. The following equation has been derived from the data in Table VI: Relative Energy (log new ball diam in in. + 0.410) Input = --------------—--------------- from which the relative energy inputs for balls of different sizes can be calculated and compared. The relative energy input is unity for balls of 2.715 in. diam. The equation indicates that the work accomplished by a ton of grinding balls per unit of energy input is roughly proportional to the square root of the total ball surface area; provided, of course, that the balls are sufficiently large to break the material. The data in support of this statement are admittedly meager, but are fairly consistent when plotted. The relative grindability values listed in Table VI for 200 mesh multiplied by 4/5 apparently correspond approximately to the A-C grindability at 200 mesh.' It would seem that for open circuit tests comparable accuracy could be obtained much more simply by the old method' of plotting the test grind, extending the mesh grinds to the left of zero time if necessary, and determining from the plot the equivalent time required to grind from the plant feed size to the plant product size, using the average of several mesh sizes. The en- ergy input value of one time interval could be determined by tests on materials of known grinding resistance, and this multiplied by the interval required should give the desired energy input value. The relative grindabilities would be the relative time intervals required for a specified feed and product size. When the plotted mesh size lines of a homogeneous material are extended to the left beyond zero time they meet at one point at zero pct passing. The horizontal distance of this point from zero time indicates the equivalent energy input required to prepare the mill feed. The author's results show that the closed circuit grinding tests give about the same K values as open circuit tests, from which he concludes that open circuit tests are satisfactory in many cases. The value of the closed circuit test is its ability accurately to predict energy requirements in closed circuit grinding for both homogeneous and heterogeneous materials. If the material is homogeneous, the open circuit test gives satisfactory results; but if the material contains appreciable fractions of hard and soft grinding ore, the open circuit tests will not be accurate because of the accumulation of hard grinding material in the circulating load. Since in most cases it is not possible to determine a priori whether the material contains hard and soft fractions, the closed circuit tests are preferable and more reliable. B. S. Crocker (Lake Shore Mines, Ontario)—Dr. Roberts probability theory of grinding is very similar to our log pct reduced vs. log tonnage method of plotting and evaluating grinding tests at Lake Shore. However, although we both seem to start at the same point we finish with different end results. Shortly after publishing our grinding paper (referred to by Dr. Roberts) in 1939, we did pursue the subject of the "constant pct reduction in the pct +28 micron material for each constant interval of time. We ran innumerable tonnage tests on the plant ball mills, rod mills, tube mills with 11/4 and 3/4 balls, and lastly pebble mills, with tonnage variations from 180 tons per day to 950 tons per day. We found that when we plotted the log of the tonnage against the log of the pct reduced of any reliable mesh, we had a straight line up until 90 pct of the mesh is reduced. We have also tested this in our 12-in. laboratory mill with the same results. We have used this method of evaluating grinds for the past 8 years and developed the recent four stage pebble plant on this basis. By pct reduced we mean the percentage of any given mesh that is reduced in one pass through a mill at a given tonnage (or time). For example, if the feed to a rod mill is 90 pct +35 mesh and the discharge at 500 tons per day is 54 pct +35, the pct reduced is 90 — 54/90 = 40 pct. If the feed had been 80 pct +35 the discharge would have been 48 pct +35 or pct re- duced 80-48/80 = 40 pct as long as the tonnage re- mained constant at 500 tons per day. Thus we can easily correct for normal variation of mill feeds. This log — log relationship derived from the tonnage tests of all our operating mills has proved of tremendous help in checking laboratory work and in designing alternate layouts or new plants. The difference between the log — log and the semi-log plot is only shown up when the extremes in tonnages are plotted. When the relationship between the pct reduced and the tonnage was first investigated, we used semilog

Jan 1, 1952

By David Kellogg

THE electrodeposition of iron has been practiced for many years. The earlier work along this line was directed toward the preparation of pure metal, but later applications were the production of thin adherent coatings as used in the electrotyping of Russian banknotes in 1860. A historical discussion of this subject, however, would require too much space and would be inconclusive. Much has been written on the subject but no two experimenters use the same methods or materials. During the war, the British army repair, shops developed a method for building up worn parts of automotive machinery, aero engines, etc., using the cold surfate . bath and low-current density method.1 The method has been used successfully in commercial work for the production of about 6000 repaired parts, therefore experiments along the same lines have since been made at the Westinghouse research laboratory. The apparatus used was essentially that described in the article mentioned except that the current -used for cleaning was obtained from a 3/4-kw. 60-volt, house-lighting generator, direct connected to a 2-h.p., 870-r.p.m., 440-volt, three-phase, type CS induction motor; while the plating current was taken from the storage batteries at any desired voltage. The anodes were made from 0.036 in. (0.9 mm.) Armco iron made into cylinders 5 in. (127 mm.) long by 8 in. (203 mm.) in diameter with a disk of 1/8 -in. (3.17 mm.) micarta, having a 2 in. hole in the center fitted at each end of the cylinder for stirring. The anodes were hung on a wooden rocker frame driven by a wooden connecting I rod directly connected to a small reducing gear, such as is sold by most of the apparatus supply firms; 3 gal. stoneware crocks were used as containers. The solution used by Thomas, 75 gm. of the crystallized ferrous ammonium sulfate per liter, was tried, using the current density recommended by him; namely, 0.33 amp. per sq. dm. Under these conditions the deposit on a ½ -in.

Jan 2, 1922

By M. G. Benz, J. F. Elliott

The austenite solidus of the iron-carbon system has been determined using a series of diffusion couples, each of which consisted of a specimen of austenite held in contact with a melt saturated with austenite. After the equilibrium distribution of carbon had been established by diffusion at a specified temperature, i.e. the austenite specimen had become austenite of the solidus conzposition, the diffusion couple was cooled, sectioned and anazlyzed for carbon. The solidus was found to be a straight line: A revised iron-carbon temperature-composition diagram is presented, COMPOSITION has a marked effect on the temperature at which austenite begins to melt and the austenite solidus of the iron-carbon system describing this effect has been the subject of many investigations.1-10 The significant results of these investigations are presented in Fig. 1. The experimental methods and purity of the materials used in them are summarized in Table I. In plotting the data in Fig. 1 no attempt has been made to convert these results to the International Temperature Scale of 1948," except for the data of Adcock,5 as this conversion would do little to reduce the uncertainty that exists as to the position and shape of the solidus. A point of major concern in evaluating these data is that the alloys studied, except those used by Adcock, were not binary alloys of iron and carbon, Table I. Also, it would appear that several of the methods did not permit equilibrium to be established through the system being studied. All that can be said for the results of these investigations is that they indicate only approximately the location of the solidus with the uncertainty as to its location at 1 pct C being approximately 100°C. The current investigation was undertaken to provide reliable data by which the austenite solidus could be established. It was hoped that information on the liquidus also could be developed at the same time, but experimental limitations prevented this as austenite segregated from the liquid on cooling. After a careful study of possible experimental methods and extensive laboratory tests, it was decided that the use of a series of austenite-liquid diffusion couples would provide the most reliable results. This paper describes the method and its results and also includes a complete iron-carbon temperature-composition diagram based on what are considered to be the best available data. EXPERTMENTAL METHOD The diffusion couple used for this investigation consisted of a small cylindrical pellet of austenite held in contact, at a specified temperature, with a melt saturated with austenite. The composition of the cylindrical austenite pellet was chosen to be approximately 0.1 wt pct C less than the estimated

Jan 1, 1962

By L. D. Jaffe

THE data recently published1-" on heat treatment of titanium alloys have not been readily systematized into an overall picture. When the ß titanium phase transforms isothermally at low temperatures, the hardness follows a typical age-hardening pattern, going through a peak as schematized by the "hardness" vs "time of isothermal transformation" coordinates of Fig. 1. As the temperature is raised, the peak will decrease in height and occur at shorter times; slowing must however take place as the /3 transus is approached. The brittle microconstituent in the region of peak hardness has been termed /3'. Its structure is still undetermined but it is clearly a transition stage from soft /3 to the £ + a that is found at the right of the peak. On continuous cooling, high cooling rates correspond to short times on Fig. 1; abscissa labeling has been added accordingly. Extremely rapid cooling will retain soft /3; very slow cooling will precipitate soft a; intermediate rates give hard 8'. Increasing distance from the water-quenched end of a Jominy hardenability bar corresponds to slower cooling (right on Fig. I), but the range of cooling rates covered by a Jominy bar is only a small portion of that shown in the figure. The p-stabilizing alloying elements retard the transformation process, moving the material to the left on Fig. 1. A lean alloy is harder water-quenched (P') than air-cooled (/3 +a); a rich alloy is harder air-cooled (/3') than water-quenched (/3). Examples of the position of various compositions with respect to the curve, based on limited data in the literature, are given at the top of the figure. Oxygen and carbon accelerate the transformation process, moving the material to the right on Fig. 1. If an alloy quenched quickly enough to retain soft /3 is reheated below the £ transus (tempered), it ages, going through a hardness maximum as time increases (moving right on Fig. 1). Material which after cooling from the /3 range lies on or right of the hardness peak, will move still further right on tempering, and so soften. Since the rate of the tempering (aging) reaction increases with temperature, the figure also may be used to represent the variation in properties with tempering temperature, at short tempering times. The simple picture given here neglects martensite transformation, as well as differences between decomposition products of /3 formed by direct isothermal transformation and those formed by quenching and tempering. It may nevertheless be of use as a guide for practical heat treatment and for further research.

Jan 1, 1955

By R. E. Ogilvie, N. L. Peterson

Diffi-lsion measurements were conducted at all compositims in the bcc solid solution of the U-Nb system employing incremental couples at composition intemals of 10 at. pct. Diffusion coefficients were determined by the Matano method from concentration gradients obtained with the electron-probe microanalyzer. The activation energy for inter-diffi-lsion as a function of compositim shows three distinct regions: 1) 80 to 100 pct U.6= 30 kcal per mole; 2) 20 to 80 pct U, $ - 70 kcal per mole; 3) Oto 20 pet U, Q = i40 kcal per mole. The frequency factor, fi0 and the activation energy $ were found to be roughly related by the following equation: log Do ^9.7 X IO-5Q -6,6. The Kirkendall marker movement indicates that DU is larger than DNb between 16 and 100 pct U and DNb is larger than DU from 0 to 4 pct U. FOR practical as well as fundamental reasons, the rates of diffusion in alloys are of considerable consequence. Most solid-state reactions are largely dependent upon the diffusion of atoms through the lattice structure and along grain boundaries. The high-temperature strength and reasonable nuclear properties of niobium have prompted its use as a reactor material in contact with uranium fuel. Hence, diffusion data for the U-Nb system are of considerable importance. In the previous diffusion study1 on the U-Nb system using pure element couples, reliable data were obtained only in the range of 0 to 10 at. pct Nb due to the large variance of the diffusion coefficient with composition. Also, a large Kirkendall effect and considerable porosity in the uranium-rich areas of the specimen were reported, which suggests that the true diffusion coefficients are somewhat larger. The purpose of the present study was to obtain reliable diffusion coefficients at all compositions using incremental diffusion couples with intervals of 10 at. pct. In view of the abnormal self-diffusion be- havior of y uranium2-4 and some other bcc transition elements,&apos;-&apos; it was felt that a comparison of the interdiffusion coefficients in the bcc U-Nb system with those of Reynolds et al.9 for the fcc gold-nickel system might shed some light on the diffusion mechanism involved. Both systems have similar phase diagrams, in that complete solid solubility exists above a miscibility gap. EXPERIMENTAL PROCEDURE The uranium used in this investigation was obtained through the courtesy of Argonne National Laboratory. An analysis of this material detected only Si-30, A1-7, C-6, N < 10 and 0-18 ppm. The niobium was electron-beam melted material obtained from Stauffer-Temescal. The gaseous impurities were less than 50 ppm, and the spec troc hemical analysis showed Ta-500 and W-200 ppm. U-Nb alloys were prepared at composition intervals of 10 at. pct by melting the appropriate amounts of the pure elements in an arc furnace. The buttons were inverted and remelted 6 times to assure complete mixing. The buttons were then wrapped in molybdenum foil, canned in Zircaloy-2 or stainless steel, and hot rolled 30 pct reduction in thickness at temperatures between 850" and 1100°C. Alloys with 10, 20, 30, 40, and 90 at. pct Nb rolled quite easily under these conditions, but the 50, 60, 70, and 80 pct alloys remained brittle. After melting and rolling (when possible), the alloys were annealed for 24 hr at a temperature within 100°C of their melting point in a dynamic vacuum of better than 4 x 10-8 mm Hg. These treatments produced alloys which were homogeneous on a 1 p scale within the detectability limits of the electron probe. During fabrication, the alloys picked up as much as 100 ppm Mo and 100 ppm Zr. Other elements checked for but not found were Co, Cr, Fe, Mn, Ni, and Ti. The grain size of the annealed samples ranged from 3 mm for the uranium-rich alloys to 0.3 mm for the niobium-rich alloys. This permitted measurements of the concentration gradients in the diffusion samples without crossing more than one or two grains, thereby eliminating any grain boundary effects. The specimens were bonded by theU&apos;picture frame" technique as reported by Kittel.10 Specimens of composition b)U + (100 - x)Nb were sandwiched between two specimens of composition (x + 10)U + (90 - x)Nb after they were ground flat and parallel

Jan 1, 1963

By Frederic P. Dewey

This old and well-known method of determining silver is, in bullion work, so far superior to the furnace-assay that it is looked upon with reverential awe by many, if not by most, users, and its ease of execution, with proper equipment, commends it highly where much commercial bullion work on silver is required. The method is so thoroughly well known that a description of it here may seem to be unnecessary, but many thousands of determinations are annually made by it in the U. S. Mint Service and its practice is there reduced to an art. This is necessary both for the sake of economy of time, and because high-grade work with it requires constant practice. It is useless for a person who uses it only occasionally to expect to attain high accuracy with it, without spending more time upon a detemination than is warranted in a busy commercial laboratory. It is always employed in the Mint service whenever possible, but its chief field is in the determination of silver in standard silver (ingots and coin), which is 900 fine in silver and 100 fine in copper, and I shall first briefly outline its use on this metal and then take up various points in detail, especially as related to the accuracy of the results obtained. For this determination 1,115 mg. of standard metal are weighed and transferred to a glass-stoppered bottle, the metal is dissolved in nitric acid, and 100 cc. of a standard solution of NaCl run in. The bottle is then vigorously shaken and a measured portion of a decimal salt solution added, and again shaken, if necessary. These operations are repeated until the silver is precipitated. Standard metal being 900 fine, 1,115 mg. should carry 1,003.5 mg. of silver, which is a convenient figure to work with.

Jan 1, 1914

By Bieniawski, Z. T.

The importance of understanding the phenomena associated with rock fracture has long been fully appreciated in rock mechanics. This is clearly apparent from the special attention paid to rock fracture in the comprehensive papers published within the past four years. These papers present a picture of how the knowledge of brittle fracture of rock was gradually enriched and also show that what was often taken for granted three or four years ago is no longer considered as valid today.

Jan 1, 1972

By John B. Pearse

IN order to get an idea as to the strength of steel rails, it will be well to review the tests to which iron rails have been subjected. In England, Mr. Ashcroft found that the best 80 pound rails broke under a 300 pound weight, falling 15 feet. In Germany the Society of Railway tyfanage1-s determined 011 and have long applied a test of 1000 pounds falling 101/2 feet, as the standard which all first-class iron rails must reach. In this country no inspection nor test is applied, but tests made show that iron rails fro; our most reliable makers, break under a G foot fall of a 1500 pound drop as an extreme test, most of those tested breaking under a far less test; some breaking with less than a 3 foot fall of the same weight. Everywhere where steel has been used, engineers have come to the conclusion that some test is required to show the regularity and strength of the product. As compared with iron, the tests which steel will stand are wonderful. After numerous experiments partially based on the experience of the rail-mill at Graz, belonging to the Southern Railway of Austria, the Society of German Railway Managers fixed upon a test of 2000 pounds falling 138 feet. They found that this test represented the steel which suited their necessities, and also found that with steel of otherwise average purity, this test represented about one-half per cent. of carbon, and made it a rule to take no steel containing under three-tenths of a per cent. of carbon, because it was too soft. They expressed a hope that a harder steel could soon be made tough enough to stand the same test. I n England, a test was adopted of 2240 pounds, falling 15 to 17 feet on the rail on heavy bearings. This test has been found satisfactory under heavy traffic on average road-beds, and has been invariably

By K. J. Gill, P. Chiotti

Thermal, metallographic, and vapor pressure data were obtained to establish the phase diagram for the thorium-zinc system. Four compounds corresponding to the stoichiometric formulas Th2Zn, ThZn2, ThZn4, and Th2Zn17 were observed. The melting points of these compounds under constrained vapor conditions were found to be 1055°, 1105°, 1095°, and 1015°C respectively. Four eutectics exist in this system with the following eutectic temperatures and thorium contents in wt pct: 1040°C, 89 Th; 945°C, 79 Th; 1045°C, 55 Th; and 995°C, 35 Th. The standard free energy, enthalpy, and entropy of formation for the compounds were determined from zinc vapor pressure data. ALTHOUGH the thorium-zinc system has been of technical importance in the commercial production of thorium and more recently of interest to some proposed pyrometallurgical separations processes for reactor fuels or blanket materials no detailed investigation of this system has been made in the past. Some previous work has been reviewed by Hanssen.1 The existence of four compounds, Th2Zn17, ThZn4, ThZn2, and Th2Zn has been established and their crystal structures have been studied by X-ray diffraction techniques.2-4 Smirnov et al.,5 determined the solubility of thorium in zinc and investigated the two-phase region between Th2Zn17 and zinc. They calculated some of the thermodynamic properties for these alloys from emf measurements on the cells Th/ThCl4(fused)/Cl2, C and Th2Zn17(s)+ Zn (l)/ThCl4(fused)/Cl2, C. The possibility of reaction between the anode materials and fused thorium tetrachloride to produce a lower valent thorium salt would have to be resolved in order to evaluate the results obtained. The purpose of the present investigation is to establish the phase diagram for the thorium-zinc system and to determine the standard free energy, enthalpy, and entropy of formation for the compounds formed. MATERIALS AND EXPERIMENTAL PROCEDURES The metals employed in the preparation of alloys were Bunker Hill slab zinc, 99.99 pct pure and Ames Lalboratory thorium. The major impurities in the thorium in parts per million were oxygen—1250, carbon—350, iron—100, nitrogen-75, and silicon—70. The metals in the form of several small massive pieces, total weight about 30 g, were cleaned with acid, washed with water and acetone, and dried just prior to their use for alloy preparation. Tantalum containers were found to be suitable for all the alloys studied and were used throughout this investigation. The metals were sealed inside of small 1-in.-diam tantalum crucibles by welding on preformed tantalum covers. A small thermocouple well made from 1/8-in.-diam tantalum tubing was welded in the bottom of each crucible. These crucibles were enclosed in

Jan 1, 1962

By James E. York

THE honor so fairly earned and so incompletely and tardily paid to Henry Cort, the inventor of the puddling-furnace and the, rolling-mill, has been fully set forth by Mr. Charles H. Morgan,1 and needs no further emphasis here. In view of the importance of the rolling-mill in the treatment of iron and steel, the paucity of information concerning it is surprising. With the exception of a hook, written about 35 years ago, by Peter Bitter von Tunner, an Honorary Member of this Institute, and of desultory articles on simple sections, which have appeared in technical journals, I know of no pub¬lication attempting to treat this subject, although volumes have been written on the scientific theory and technical manipulations involved in other branches of the iron- and steel-industry. This strange anomaly may be due to the fact that roll-turning cannot be called a scientific business. It does not ordinarily come within the range of an educated engineer; yet it cannot be performed by an ordinary mechanic. It demands some of the qualifications of an engineer, in designing, and those of a mechanic, in execution. The men who have followed this trade have controlled the training of their successors. In many cases the technical knowledge required bas been handed down from father to son, and there has been a motive of private interest to prevent its public dissemination. Moreover, the statement of the various principles involved in the process would require, besides manual experience, a degree of scientific knowledge which roll-turners do not usually possess; and, finally, any book on the subject, in order to possess real, practical value, would have to be so fully illustrated as to make it very costly to publish. Regarding my own experience, I may say that I served a six-

May 1, 1906

By Lyden, Joseph P.

THE Picher Mining Field, fig. 1, which lies between Baxter Springs, Kansas, and Commerce, Okla., is the most intensely mineralized and the largest zinc-lead ore producing area in the Tri-State District of Missouri, Kansas, and Oklahoma. It has a vast lateral extent of underground workings that is unequaled for the observation of the geology of zinc-lead ore bodies in sedimentary horizons; and thousands of churn drill holes in the unmined areas supplement the underground observations with useful data for the interpretation of the geology. This paper is confined to the ore deposits of the Picher mining field. The reader is referred to the bibliography for the general geology of the Tri-State district which has been ably covered by many geologists. The writer was co-author of several publications on the Tri-State district.- This paper is necessarily a repetition of parts of those publications but contains a few changes and additions on the deposition of the minerals. The parts of this paper concerning mineralization maps and pipe slump-structures are not covered in the above publications.

Jan 1, 1950

By E. S. Shaw

Utah continues as a very unimportant factor in oil and gas production. During the year 1933 there were no developments of noteworthy significance. There were no completions of either producers or dry holes during the year. The only commercial production in Utah has been from the five fields listed in Table 1 and mentioned briefly in the following paragraphs. Virgin Field.—Oil was first discovered in 1907 in a well drilled in sec. 13, T.41S., R.12W. Of the first 15 wells drilled, all but three were failures. In 1920 production from four wells from 550 to 600 ft. deep was about 20 bbl. per day. San Juan Field.—The majority of drilling in this area was done during the years 1908 to 1911. Probably the first commercial well in the field was that drilled in NW.$i sec. 6, T.42S1 R.l9E., in 1909. Farnham Dome.—The discovery well was drilled by the Utah Oil Refining Co. in April, 1923. A number of years later a second well was drilled by The Carbon Dioxice a mica1 Co., the present operator, which markets the gas in the manufacture of "dry ice" and allied products. The eslimated production, as indicated in Table 1, includes 500 million cubic feet estimated to have been lost while drilling the discovery well. Cisco Dome.—The discovery well was drilled by The Utah Oil Refining Co. in November, 1924. The Crystal Carbon Co. markets the gas in the manufacture of carbon black. Ashley Valley Dome.—The discovery well was drilled by the Utah Oil Refining Co. in April, 1925. The Uintah Gas Co. markets the gas in Vernal, Utah, for fuel. Woodside Structure.—In February, 1924, gas was discovered in a well drilled by Utah Oil Refining Co. in sec. 12, T.l9S., R.l3N., on the Woodside structure. This gas is reported to contain an appreciable amount of helium. It is being held as a helium reserve by the United States Government. Salt Valley Structure.—The test of the Utah Southern Oil Co. in sec. 31, T.23S., R.21E., on the Salt Valley structure has been shut down for some time at 6120 ft. This test has passed through more than 5000 ft.

Jan 1, 1934

H. W. Turner, Portland, Ore. (communication to the Secretary*) :—Mr. Brown&apos;s paper on the complicated groups of veins exposed in the workings of the Bodie mine forme a valuable contribution to the literature of the structural features of ore-depoeits. It is much to be desired that managers should put into print the results of their observations of the mines under their charge. These observations, as well as data of production, kind of ores, etc., usually accumulate for years, and unless the mining geologists of the Geological Survey happen along before the mine is worked out, such data seldom get into print. About the year 1899 I went through the mines at Bodie with R. C. Turner, then superintendent, and made some notes on the veins and gangue-minerals, and collected some specimens. Mr. Brown refers to crystals of feldspar (albite) found on fragments of quartz on the surface. I collected a number of specimens of these crystals, mostly from Queen Bee hill, and

Jan 1, 1909

By HOWARD RICHARDS

THE dollar was, selected as the unit of currency by the Congress of the United States of America on Apr. 2, 1792. This "Dollar" currency is so much more convenient than the older British currency that the Canadian Government, among others, has adopted it with corresponding success. Just as the dollar is the unit of United States currency, so the meter is the international unit for measuring length. The various weights and measures used in - the United States have since Apr. 5,. 1893, been based on the metric standards. These fundamental standards are kept by the International Bureau of Weights and Measures, which is supported by the United States, Great Britain and the, other leading countries. of the world. Copies are held-in Washington and other capitals. (2) As the dollar is divided into 100 cents, so the meter, which is 10 per cent. longer than the yard, is divided into 100 centimeters or cm. And as the cent is divided into 10 mills, so the centimeter is divided into 10 millimeters or mm. In measuring clothing and other articles which do not require great accuracy, the centimeter is most con¬venient, so that such work is done in terms of centi¬meters.. Instead of speaking of a 15;2-in. collar, a 40-centimeter or 40-cm. collar is referred to. Where accuracy is needed, as in mechanical drawing, machineshop work, etc., millimeters are employed. Thus 8 mm., is the convenient equivalent for 5/16 inch.

Jan 1, 1921

By Perry G. Harrison

The increased use of sintering for the beneficiation of iron ores and the reclaiming of flue dust creates a lively interest in sintering costs and economics. The character of material sintered and geographical location of plants so radically alter sintering costs and economics that it is well.to understand at least the basic elements which control such changes. The following cost factors are believed to be roughly approximated for large-scale Dwight-Lloyd continuously operated sinter-machine installations located anywhere. Per Crude Ton Labor, supplies and repairs 0.15 Power 6.5¢ X kw-hr. rate ? Plant overhead and administration 0.05 Depreciation per ton annual capacity 0.05 Fuel: 6 per cent coke breeze or equivalent minimum ? 1 per cent coke breeze additional for each 5 per cent free and combined water in ore or dust ? Ignition distillate at 0.6 gal. per ton ? Per Sinter Ton Royalty on ore 0.10 Royalty on flue dust 0.15 Per Crude Ton "Winter expense"; i. e., the cost of the five months enforced idle . period for plants tied in to Great Lakes transportation season 0.03 Using the foregoing data, it is possible to roughly approximate the cost of efficient sintering at any location for any ore, viz: Per Crude Ton Per Ton Handled Sinter 1. Flue Dust—Steel Plant Locations Sinter recovery, 15 per cent moisture and carbon 85 per cent Labor, supplies and repairs 0.15 0.18 Power 6.5¢ X 1¢ kw-hr. 0.065 0.08 Plant overhead and administration 0.05 0.06 Depreciation per ton 0.05 0.06 Dust handling and preparation 0.10 0.12 Fuel: free, contained in dust Ignition: blast-furnace gas free Royalty 0.15 Total $0.65 Note:—Cost increased by either deficiency or considerable excess of carbon in dust.

Jan 1, 1932