Search Documents

By B. Woyski

Many writers, in discussing defects caused by oxidation and gassing of bronzes and red brasses advocate substantially the same cure for both. But from its nature, oxidation cannot take place if there is an excess of fuel in the furnace, while the gases absorbed by some alloys are products of incomplete combustion of the fuel. Hence the metal can be either oxidized or gassed, but it is doubtful whether these actions can take place simultaneously. Oxidation can be easily overcome by the use of deosidizers or it may be avoided by protecting the molten metal with suitable fluxes. Absorption of gascs is more difficult to overcome: the regulation of the air and fuel, so as to produce complete combustion, and the protection of the bath by mineral fluxes arc the most important factors. Gas expulsion, resulting in gas holes, porosity, unsoundness, and swollen or cauliflower-headed risers, is said to have several causes. One writer1 lists the most common causes in the order of their importance, as follows: Superheated metal, dirty or slaggy furnace conditions, using metals low in quality or those previously subjected to bad melting practice, poor grade of fuel, use of newly lined or damp ladles, indiscriminate mixing of scrap or illogical combinations of metal. Superheating the metal usually occurs when the heat is ready to be poured but for some reason must be held in the furnace. In this case, a careful furnace tender tries to avoid overheating the metal by keeping a mild fire; that is, a reducing fire which, unfortunately, results in gassing the metal. A dirty, slaggy furnace may result in gassing the metal by retarding the heating and prolonging the time necessary to bring the metal to the proper temperature, thereby increasing the chances of gassing in uncertain furnace atmosphere. It is doubtful whether rnetals of low quality have anything to do with gassing molten metal, except, possibly in the case of metals containing

Jan 1, 1923

Last October a committee was appointed by The War Service Association of Manufacturers of Solder and Bearing Metals, Inc. to consider the report of the U. S. Bureau of Standards to the Conservation Division of the War Industries Board, a letter of the War Industries Board, and the discussions of this letter as reported at the meetings of association and to summarize the information thus obtained. The report of this committee has just been printed. The committee agrees with the Bureau of Standards that 99 per cent. tin can be used. It also finds that a very small amount of lead might increase the tendency of the bearing to crack and that lead has a hardening effect on babbitts up to a possible limit of 10 per cent. of lead. Still in the so-called genuine babbitts, in the presence of lead a certain proportion of low melting point eutectic is introduced which admits of the bearing being poured into thinner sections and is decidedly advantageous in the die-casting process in producing a much smoother casting. But the committee recommends that the Bureau of Standards thoroughly investigate this point. Lead-base babbitts, to give satisfactory service, must be carefully made of the proper raw materials. The bronze hearing that has been thoroughly tinned and containing the thinnest possible babbitt lining is now becoming recognized as the ideal bearing. The compositions, recommended by the committee are as follows:

Jan 2, 1919

By Clint L. Milliken

The smelter is often considered the flywheel of the copper industry. No other unit can produce such a uniform product from so many starting materials. Direct-smelting ore, concentrate, precipitate, refinery slag, and scrap in almost any combination can be processed into blister or anode copper. Copper smelting practice has advanced little in the last century. It is still basically matte smelting, although the source of matte has changed from the blast furnace to the reverberatory furnace because of changes in smelter feed, and the Great Falls converter has been replaced by the Peirce-Smith converter. This lack of progress has continued because the economic forces required to produce change have not been of sufficient magnitude. Traditionally, the smelting, operation has required only about 10% of the total cost of producing copper from its ores and this minor cost item has not warranted change until recently.

Jan 1, 1971

By Robert L. Haffner

When mining operations of The Eagle-Picher Co. began in the Illinois-Wisconsin zinc mining field in 1949, all underground loading of broken ore and waste was by caterpillar-tracked machines. Beginning in 1956 rubber-tired end-loaders were brought in; ultimately they completely supplanted the tracked units. End-loaders proved to have the mobility needed for the mining conditions and additional merit in auxiliary capacities. Eagle-Picher operates five mines in this area; two are entered by shafts and three by inclined adits. Several ore zones, some of which are attenuated over a considerable distance, are worked from the same entry. Consequently underground haulage roads connecting or following these orebodies have attained great length. In addition, working places are often widely separated because of the character of the mining operations which include pillar recovery and extending haulage connections into old workings. At one mine, the haulage distance is 5000 ft on either side of the shaft, at another the maximum one-way distance is 8400 ft, and at another the present road system of 6800 ft is expected to reach 10,000 to 12,000 ft.

Jan 6, 1962

By H. N. Hall

Various factors must be considered in an engineering evaluation of gravity-drainage reservoirs. Among these are: (1) the effect of producing rate on total oil recovery; (2) the effect upon well productivity and ultimate recovery of the pressure level maintained during the producing life of the reservoir; (3) the economic advantage of full or partial pressure maintenance; and (4) estimate of the rate of gas production and injection and the possible purchase of gas under conditions of full pressure maintenance to ascertain compressor facilities needed. All of these factors can be evaluated only when a reliable method is employed for determining reservoir performance in gravity-drainage reservoirs. The purpose of this paper is to present a general method for calculating the performance of a gravity-drainage reservoir. This method is applicable for conditions of complete pressure maintenance, partial pressure maintenance and normal pressure depletion. Provisions are made to take into account variations throughout the reservoir of reservoir configuration, changes in permeability and fluid composition. Based on the method presented in this paper, an IBM 650 computer program has been developed. The past performance of an actual gravity-drainage reservoir producing under conditions of declining pressure and no gas injection was duplicated using this program. INTRODUCTION In tilted reservoirs the production of oil is influenced by drainage of oil from upstructure to downstructure locations. When this downstructure drainage of oil is sufficient to cause effective segregation of the gas and oil in a reservoir, the reservoir is usually classified as a segregation drive or gravity-drainage reservoir. (Discussion will be restricted to gravity-drainage reservoirs which have no encroachment of edge water.) The important feature in gravity-drainage reservoirs is the density difference between reservoir oil and gas. These phases tend to segregate in the reservoir with the result that in the gas cap the oil saturation is maintained at a higher level by drainage of oil from the gas-cap area. Oil can be produced from the oil zone at a low gas-oil ratio and reservoir energy is thereby conserved. The standard material balance in not adequate for predicting gravity-dramage reservoir performance because it does not take into account the difference in saturation above and below the gas-oil contact. Several authors'.' have presented methods for calculating the performance of gravity-drainage reservoirs in which reservoir pressure is maintained constant by gas injection into the gas cap. Using some simplifying assumptions, these methods can be employed with a desk calculator to give acceptable results. The problem of predicting the performance of gravity-drainage reservoirs under the conditions of declining reservoir pressure is many time more complex than that of constant pressure. fierefore, attempis to develop a method suitable for desk calculation have required excessively simplified assumptions. In the past several years, highspeed digital computers have become more widely available for reservoir engineering problems. These corn puters are well suited to problems such as the prediction of the performance of gravity-drainage reservoirs with pressure decline. Many of the simplifying assumptions necessary for hand computation can be eliminated so that a realistic approach to the gravity-drainage process can be made. CONCEPTUAL PICTURE OF OIL MOVEMENT IN GRAVITY-DRAINAGE RESERVOIRS Before attempting to develop an analytical treatment for conditions occuring in a gravity-drainage reservoir, a concept should be formed concerning the movement of fluids in the reservoir as oil is produced. A review of the literature'.' shows that it is customary to classify gravity-drainage operations into two categories—(1) with complete pressure maintenance, and (2) with declining pressure. The same line of reasoning will be followed in presenting the concept of the movement of fluids in the reservoir because it is easier to visualize the movement of fluids under conditions of complete pressure maintenance. After discussing complete pressure maintenance, an analogy will be made between that and the case of declining pressure. It should be kept in mind throughout that the final aim for the problem of solving gravity-drainage performance with digital computers will be to develop a general program for any kind of gravity-drainage reservoir. COMPLETE PRESSURE MAINTENANCE One feature which is generally common in gravity-drainage reservoirs is a gas cap located at the top of the structure. This is shown in Fig. 1(a). Fig. l(b) shows oil saturations that might occur through the reservoir. In the gas cap, oil saturation is lower than

By R. P. Alger, M. P. Tixier, D. R. Tanguy

In the combination induction-electrical log used at present in the field, the induction logging tool is appropriate for the investigation of moderately invaded formations. A new induction sonde with a radius and investigation about twice as large has been developed recently for the case of deep invasion. It has very nearly the same vertical resolution as the present sonde so that thin beds are defined as accurately as before. The characteristics of the new tool are described, the corresponding interpretation charts are given and field examples are discussed. The design of the sonic logging tool has been modified to improve the calibration and the reliability. The fact that porosity can be accurately recorded by means of the sonic log has prompted new interpretation procedures for saturation estimation, wherein the data concerning the various permeable beds in a given well are correlated. One approach consists of plotting transit time vs true resistivity, with an appropriate scale. With this approach, saturations can be estimated conveniently even in cases where formation water resistivity is not well known. In another approach, a comparison is made of the values of the formation waters computed from the re- sistivity and sonic logs. Using the concept of continuity, this procedure makes possible a quick determination of zones of saturation in shaly sands and/or in case of appreciable variations of formation salinities with depth. It has been found that the comparison of porosity from the sonic log with the apparent porosity computed from a short-investigation resistivity log may reveal, in many cases, the presence of residual oil and thus detect potentially productive formations; this procedure is valuable when the true formation resistivity and the resistivity of the formation water are in doubt. INTRODUCTION During the past year, the efficiency of log interpretation has been vastly improved. The improvements have largely resulted from the introduction of a deep-investigation induction device and from the application of new interpretation techniques that utilize sonic vs resistivity readings. Since the new interpretation techniques depend, in part, upon good values of true formation resistivity, the new induction log will be discussed under Part I. The sonic interpretation techniques will be studied under Part 11. Early in 1959, the 6FF40 induction equipment was introduced in the field. This device was designed for a better approach to true formation resistivities in deeply invaded zones. The greatly improved radial investigation of the 6FF40 equipment has been achieved without sacrificing vertical resolution. The first combination induction-electrical log, the 5FF40, was introduced as a standard tool in 1956 for the logging of wells drilled with fresh muds. The tool has received wide industry acceptance in the United States. 'The 5FF40 induction log has a radial investigation sufficient to overcome average depths of mud filtrate invasion. At 5d invasion, for example, the 5FF40 induction log will read about 1.4 R. in a water sand where R., = 10R,. At 10d invasion, such induction log would read 2.45 R. in the same water sand. In either case, the effects of invasion would not be sufficiently great to cause a water sand to be mistaken for a shale-free oil- or gas-producing zone. Some formations, however, invade deeply — in excess of 10d. Such water zones could be mistaken for oil-or gas-saturated sands unless the porosity balance' can clearly make the distinction. It is for these deeply invaded formations that the 6FF40 was developed. CHARACTERISTICS OF THE 6FF40 Radial Investigation Characteristics To describe the comparative responses of the 5FF40

By Pat McCarran

WHEN this Government was founded, the framers of the Constitution wrote into that instrument a provision that Congress should "coin money and fix the value thereof;" and the Constitution prohibits making anything but "gold and silver" lawful money. So silver is written into our basic law. Shortly after President Washington took office in 1789 the Congress passed the first Mint Act, setting up the U. S. Mint. In that Act, signed by President Washington on April 2, 1792, the weight of the American dollar was fixed, and it was provided how much silver should be contained in a silver dollar and how much gold should be contained in a gold dollar. It was decided that 371 1/4 grains of pure silver was to be the standard dollar of America. That standard with respect to the pure silver content of the dollar has never changed.

Jan 1, 1947

By Chester S. Conrad

SEVERAL years ago Pittsburgh Consolidation Coal Co. intensified efforts to combat the hazard of mine fires. The program consisted of three parts in the order of likely accomplishment: 1) Purchase and installation of newer and more practical fire fighting equipment. 2) Establishment of trained fire fighting teams at every mine plant. 3) A drive to remove the causes of mine fires. Experimentation with alternating current on section equipment is a major development in this part of the program. Use of alternating current to power mining equipment had been recognized as being most practical from the standpoint of safety. A means to re- place the d-c traction motor is all that has delayed complete section mechanization with a-c power.

Jan 1, 1958

By K. G. Gorling, S. J. Wallden, N. B. Lindvall

It is the policy of The Metollurgical Society to provide, in the TRANSACTIONS OF THE METALLURGICAL SOCIETY OF AIME, a prompt and accurate medium for publication of reports of significant new research in both the scientific and engineering aspects of metallurgy. Papers submitted to the Society are judged by competent reviewers according to established criteria for technical merit, accuracy, originality, and presentation. STAFF: Editorial Director, Rixford A. Beals; Associate Editor, James J. Burke; Assistants, L. Capria and R. K. Larkin. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: A. W. Thornton, Choirmon; Dennis Carney, John Chipman, J. C. Fulton, J. H. Hollomon, H. tl. Kellogg, A. E. Lee, R. Maddin, J. D. Sullivan, and O. Swan. Review and selection of manuscripts is under the supervision of the following Publications Committees: Extractive Metallurgy Division T. B. King. Cha~rmon; S. J. Dickenson, R. P. Hermsdorf, R. Schuhmann, Jr.. and P. T. Stroup. Institute of Metals Division: Robert Maddin, Chairman. F. Lincoln Vogel, Jr., Vice-chairman, W. A. Backofen, R. W. Balluffi, J. H. Bechtold, M. B. Bever, R. S. Busk, C. G. Goetzel, Paul Gordon, C. D. Graham. Jr., Robert F. Hehe-mann, R. I. Jaffee, F. E. Jaumot, Jr., lrving R. Kramer, A. J. Leno, Horold Margolin, C. J. McHorgue, Russell A. Meussner, J. 6. Newkirk, H. W. Paxton, G. E. Pell~ssier, I. S. Servi, Alan U. Seybolt, A. J. Sholer, and Sack Wahsburn. Iron and Steel Division: J. C. Fulton, Chairman; T. B King, F. C. Langenberg, W. O. Philbrook, and T. B. Winkler. Published bimonthly by the American Institute of Mining Metallurgical and Petroleum Engineers Inc., 29 West 39th Street, New York 18, N. Y. Telephonne pennsylvania 6-9220.Petroleum Subscription Engineers$20 per year for non-AIME members in United States and North South and Central 6-9220.SubscriptionAmerica $25 toreign; $5 for AIME members. Single copies, $4.00, iinalo copies Southfpr;ign,andCentral $5 00. The AIME 'is $25not responsible for any statement made or opinion expressed in its publications Copyright 1958 1958 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . Registered coble address, AIME New York . . . Indexed in Engineering Index, Industrial Arts Index, ...and Chemical Abstracts . . . Application for second class mail privileges IS pending at New Yark, N. Y. Volume 212, Number 2.

Jan 1, 1959

By Rosewell H. Johnson

Discussion of the paper of ROSWELL H. JOHNSON, presented it the San Francisco meeting, September, 1915, And printed in Bulletin No. 102, June, 1915, pp. 1291 to 1294. WILLIAM A. WILLIAMS, San. Francisco, CaI.-A sliding. scale of royalties was proposed to the Department of the Interior in connection with the fixing of royalties to be charged upon oil leases made on the Osage Reservation in Oklahoma. The possibility of evasion and difficulty of enforcement required close inspection to satisfy all interests, particularly in connection with the exemption from royalty on oil to equal maintenance and interest on the junk. Mr. Johnson discusses the block method, the period method, and the cumulative method, and favors the adoption of the cumulative method with a proviso that the wells should be permitted to be pumped until the gross income is as low as the maintenance cost, which would mean exemption from royalty on the smallest wells. He recommends that depth be the variable factor upon which the sliding royalty is based and suggests that on partially developed territory in the Osage, the royalty be one-sixth for oil wells averaging less than 2,000 ft. in depth, one-eighth for wells from 2,000 to 3,000 ft., and one-twelfth above 3,000 ft.; for the rest of the Osage he suggests one-eighth above 2,800 ft. and one-twelfth below that depth. The net result, if Mr. Johnson's suggestions had been accepted in the Osage, would have been to reduce the then existing rate of royalty and considerably increase the cost of administration. The difficulties in determining the size of wells to be exempt and the possibility of obtaining oil at different depths in the same well might lead to complications which are avoided by charging a flat royalty as now universally charged throughout the United States. It is not uncommon to reduce the royalty when the production of the wells becomes unprofitable at an existing rate of royalty, accomplishing very much the same results as Mr. Johnson has attempted to accomplish by the cumulative royalties, and probably in a manner far more satisfactory to the operator and the lessor. A. C. MCLAUGHLIN, San Francisco, Cal.-The net revenue of the well depends, first, on the cost of production; second, on the amount of oil produced; therefore it would be impossible under Mr. Johnson's system to set a royalty which would be fair to all concerned. If it is impossible to set it at the beginning, it is certainly further impossible to do it from day to clay. I think it is entirely impracticable of application.

Jan 12, 1915

By J. D. Sullivan, Chester R. Austin, J. L. Nunes

IT is characteristic of most shales and surface clays that a bloated or vesicular structure is produced by burning to a sufficiently high temperature, usually about 150° to 200°F. above the normal maturing temperature used when making common brick of the same material. Early investigators recognized this phenomenon and attributed it to the release or expansion of gases in the vitrified piece. A number of theories have been advanced on the source of the gas and the manner in which it is evolved, but none has been proved conclusively. T. E. Jackson's1 early theory that bloating was due to oxygen evolved by ferric oxide in forming ferrous oxide or ferrous silicate was never substantiated by experimental work. Orton2 thought this explanation unlikely, as all clays should bloat at the same temperature, if this were true. He found that clays bloated in the range from 1100° to 1706°C. Also, many clays containing iron did not bloat at all, but fused. Orton also stated that oxidation of different types of carbon was a source of gas during burning of clay and should be expelled before vitrification was reached. Seger3 said that he had dissolved ferric oxide in glass with no apparent evolution of gas. Matson4 came to the conclusion that ferruginous days burned to vitrification in an oxidizing atmosphere did not have the iron in a ferrous form. According to Wilson,5 the gases responsible for bloating might be entrapped air, water, sulphur dioxide, carbon monoxide, oxygen, and hydrocarbons. He spoke of two causes of bloating: (I) incomplete oxidation below the vitrification temperature, and (2) decomposition of compounds and evolution of gases above the vitrification temperature. Decomposition of calcium sulphate was given as the principal example of the latter. Bleininger and Montgomery6 stated that if any time after vitrification began the evolution of gaseous matter was rapid enough so that pressure was produced within the day, bloating was certain to take place, and a vesicular structure would be formed. They recognized that initial structure, rate of heating, kiln atmosphere, and many other variables affected bloating. Work done by the Emergency Fleet Corporation7 indicated that clays suitable for bloating should be high in compounds of metallic oxides, carbon, sulphur, sodium, potassium, or other equivalent compounds, which either act as a flux or give off gas. Orton2 studied the chemical status of the carbon, iron, and sulphur in clays during various stages of burning, using a Huron shale that bloated under oxidizing or reducing conditions. He found that only a small amount of sulphur remained in the clay and that it could be detected only by dissolving the clay in hydrofluoric acid; i.e., the sulphur was in combination with the silica. Orton said that this sulphur was probably in the form of iron sulphide dissolved in the glass phase. The iron sulphide was not broken down by heating, but was dissolved in the basic slag or glass,

Jan 1, 1942

By T. R. A. Davey

The fundamental principles by which bismuth may be removed from lead by pyrometallurgical processes are enumerated. Qualitative discussion of the phase diagrams concerned is followed by presentation of quantitative diagrams. Brief mention is made of the practical aspects. Data presented show how chemical lead (<0.005 pct Bi) may be produced by the Jollivet, Dittmer, and Kroll-Betterton processes. BISMUTH is an element whose properties are very similar to those of lead, and its minerals are associated to a greater or lesser extent with nearly all the major lead ore deposits of the world. In consequence, the lead produced contains bismuth unless a special debismuthizing process is practiced. There does not appear to be any published comprehensive review of the effect of bismuth as an impurity on the properties of lead, and there is some uncertainty as to the beneficial or detrimental effects of small amounts of bismuth in lead used for particular applications. Standard specifications of most countries stipulate a maximum bismuth content of 0.005 pct for chemical lead. With one exception, this specification is met only by lead producers whose ores are relatively bismuth-free, or whose refineries are electrolytic. In lead for certain applications a higher bismuth content is preferred by some fabricators.&apos; In contrast to the refining for silver, copper, and antimony, the refining for bismuth does not usually result in a large overalil economic gain from the sale of byproduct. Thus, debismuthizing is customarily practiced only if market conditions demand a lead with a bismuth content lower than that produced by classical refining; i.e., softening, desilverizing, and zinc refining. Until this century, debismuthizing was carried out only a:; an incidental result of desilverizing, as later described. This century has seen the development of the Betts electrolytic process—the only successful one of many electrolytic processes proposed and patented —and a number of precipitation processes based on the pioneering work of Kroll,&apos; although only one of these, the Kroll-Better ton process,&apos; is in wide commercial use today. It is proposed in this paper to deal only with the pyrometallurgical processes, excluding those based on aqueous electrolysis. Historical Background Prior to 1833 silver (and incidentally bismuth) could not be removed from lead. To recover silver from rich bullion, the only course available to lead refineries was to cupel the bullion, forming a slag of litharge. The first slag tappings or skimmings, on reduction, yielded soft lead of very low silver and bismuth contents. Intermediate skimmings yielded a lead of somewhat higher silver and bismuth contents, which could if desired be recupelled. The last skimmings yielded a litharge very high in bismuth, which could by successive oxidation and reduction cycles be separated into high purity bismuth, and lead returns. This oxidation reduction process, with modern operating techniques, can still be used today to produce a portion of a lead refinery&apos;s output of very low bismuth content, as discussed later. In 1833 Pattinsone discovered that lead bullion could be purified of silver and bismuth by fractional crystallization, the primary lead crystals formed by partial freezing being purer than the melt. Repeated processing in pans produced a lead containing as little as 0.02 pct Bi. The simple explanation of this

Jan 1, 1957

By L. E. Porter, H. P. Hassel

The state of California produced 310,-996,696 bbl. of oil and about 415,832,000 M cu. ft. of gas in 1944. Such oil production represented 18.5 per cent of the nation&apos;s production, as compared with 19 per cent in 1943 ,The tremendous demand placed upon the California fields is indicated by the monthly production in 1944, as follows: Month Barrels per Day Jan................... 809,262 Feb.................. 820,712 Mar.................. 824,592 .4pr ................. 829,973 May.................. 832,068 June.................. 846,038 July.................. 849,231 Aug.................. 858,932 Sept.................. 885,823 Oct................... 877,667 Nov.................. 876,613 Dec.................. 883,847 In all, 2100 wells in proved areas and 269 wildcats were drilled in California during the year 1944. At the end of the year, approximately 270 wells were drilling in the state, as compared with 156 wells at the same time in the preceding year. Nine new fields or new zone discoveries were made during the year, which, according to best estimates, will contribute some 77,000,000 bbl. of new reserves; in addition, the extensions of old fields will increase the new reserves about 165,000,000 bbl., or a combined total, through dis- coveries of new fields, zones, and extensions, of 242,000,000 bbl., offsetting to the extent of about 78 per cent the total oil produced during the year. Geographically, the reserves from these new field and zone discoveries and extensions are distributed as follows: Per Cent San Joaquin Valley........ 72 Coast Area............... 24 Los Angeles Basin Fields. . . 4 100 The state&apos;s reserves of crude oil at the end of the year have been estimated to be distributed as follows: The outstanding development project for the year was that of the United States Navy in the Naval Petroleum Reserve No. I, Elk Hills field. During the year, 115 wells were completed in this field, and at the close of the year an average of 19 strings of tools were drilling. This program is being jointly conducted by the Standard Oil Co. of California with the Navy and is designed to increase the production of Naval Petroleum Reserves from approxi-

Jan 1, 1945

By F. M. Jardine

I1944 the cry was for higher production more tons, more metal. New plants were built, capacity of old plants was increased and millmen all over the country were treating tonnages far above normal, sacrificing recoveries to vet that extra metal from extra tons. The list of "critical minerals," at first long, has been scratched until there remains, not a list, but only an item or two. Stocks of all metals and minerals, with possibly one or two exceptions, are now entirely adequate and numerous plants have curtailed or suspended operation.

Jan 1, 1945

By George H. Gilman

THE campaign now being waged to improve the quality of the rock-drill bit is the natural outcome f the scientific development of the drilling machine during the past twenty years. In this development there has been a great increase of power output per unit of weight of machine. But the development of the rock drilling engine has been seriously hampered by the need of a drill bit that would withstand, without undue wear or breakage, the heavy rapid blows of the improved pneumatic hammer. This problem was difficult to solve because an increase in the weight or section of the drill-steel bar resulted in decreased cutting speed and higher operating costs of both the bit and its actuating engine. The solution, therefore, is to make the bit of steel that, for a given weight or section, will be more shock and wear resisting. In the attempt to meet these requirements, many of the drill-steel manufacturers alloyed the steel with vanadium, chromium, nickel, etc., on the assumption that such elements would improve the rock-drill bit but due to the sensitiveness of such steel to forging and heat treatment, higher cost, and lack f continuity of effort on the part of the steel manufacturer to perfect this product, but little progress has been made in the adoption of these steels and the so-called straight carbon steel is today recognized as the standard material for all rock-drill bits. The first step in improving drill-bit efficiency is the determination f the cause of breakage and wear. For this reason, in 1917, certain rock-drill manufacturers, in conjunction with some of the larger mining interests, conducted exhaustive tests in both the field and laboratory. It was then found that, in the main, the cause of drill-steel troubles is not attributable to the duty imposed upon it by the normal operation of the drilling engine, but to improper forging and heat treating of the bit and to the subjecting of the bit to improper use. The fact that it is possible to minimize the troubles attributable to improper heat treatment of the drill steel has been demonstrated and it is recommended that such knowledge be made available by teaching those interested in the production, use, and up-keep of drill bits the principles on which success in this direction may be achieved.

Jan 6, 1921

By J. D. Sullivan, Chester R. Austin, J. L. Nunes

IT is characteristic of most shales and surface clays that a bloated or vesicular structure is produced by burning to a sufficiently high temperature, usually about 150° to 200°F. above the normal maturing temperature used when making common brick of the same material. Early investigators recognized this phenomenon and attributed it to the release or expansion of gases in the vitrified piece. A number of theories have been advanced on the source of the gas and the manner in which it is evolved, but none has been proved conclusively. T. E. Jackson&apos;s1 early theory that bloating was due to oxygen evolved by ferric oxide in forming ferrous oxide or ferrous silicate was never substantiated by experimental work. Orton2 thought this explanation unlikely, as all clays should bloat at the same temperature, if this were true. He found that clays bloated in the range from 1100° to I700°C. Also, many clays containing iron did not bloat at all, but fused. Orton also stated that oxidation of different types of carbon was a source of gas during burning of clay and should be expelled before vitrification was reached. Seger3 said that he had dissolved ferric oxide in glass with no apparent evolution of gas. Matson4 came to the conclusion that ferruginous clays burned to vitrification in an oxidizing atmosphere did not have the iron in a ferrous form. According to Wilson,5 the gases responsible for bloating might be entrapped air, water, sulphur dioxide, carbon monoxide, oxygen, and hydrocarbons. He spoke of two causes of bloating: (I) incomplete oxidation below the vitrification temperature, and (2) decomposition of compounds and evolution of gases above the vitrification temperature. Decomposition of calcium sulphate was given as the principal example of the latter. Bleininger and Montgomery6 stated that if any time after vitrification began the evolution of gaseous matter was rapid enough so that pressure was produced within the clay, bloating was certain to take place, and a vesicular structure would be formed. They recognized that initial structure, rate of heating, kiln atmosphere, and many other variables affected bloating. Work done by the Emergency Fleet Corporation7 indicated that clays suitable for bloating should be high in compounds of metallic oxides, carbon, sulphur, sodium, potassium, or other equivalent compounds, which either act as a flux or give off gas. Orton2 studied the chemical status of the carbon, iron, and sulphur in clays during various stages of burning, using a Huron shale that bloated under oxidizing or reducing conditions. He found that only a small amount of sulphur remained in the clay and that it could be detected only by dissolving the clay in hydrofluoric acid,i.e., the sulphur was in combination with the silica. Orton said that this sulphur was probably in the form of iron sulphide dissolved in the glass phase. The iron sulphide was not broken down by heating, but was dissolved in the basic slag or glass,

Jan 1, 1942

By G. A. Vissac

The drying of fine coal involves special techniques, which are discussed and analyzed. Types of dryers employing these techniques are described. Calculations are presented for new methods of dealing with the entrained dust that is always present in fine coal drying operations. NEW conditions, new requirements, and new methods have increased the demand for more efficient and more economical methods of drying fine coal. Dewatering of larger sizes may reduce the surface moisture to 8 or 9 pct. It is more difficult, however, to dewater sizes below 1/4 in., and some filter cakes still contain as much as 20 or 25 pct moisture. Increased freight rates and stricter consumer specifications have resulted in a demand for further reductions in moisture content. This can be obtained only by heat drying. Most modern methods of heat drying disperse or spread the mass of coal to be dried, in an atmosphere of dry hot gases. The more intimate the contact between coal particles and hot gases, the quicker and more efficient the drying operation will be. Two different techniques are generally employed, using either a fluidized condition or an entrained condition of the coal to be dried. Fluidized Condition Fluidization of a body of sand was defined and explained by Fraser and Yancey in a paper published in 1926.&apos; This condition was artificially obtained and maintained by proper regulation of the rate of air flowing through the sand body. "The sand bath &apos;boils&apos; uniformly on the surface," they write, "and feels like a fluid." The fluidization technique was also described and analyzed by Steinmetzer2 in connection with the operation of an air cleaning table. His main conclusions are as follows: "Fluidity is, for the particles involved, the possibility of motion with minimum friction. . . . Then fluidity requires the introduction of various forms of energy capable of neutralising frictions. Two solutions can be used— air and/or mechanical motions (such as the shaking motion of the carrying deck of the air table). The combination of mechanical and air energy will give the widest margins of size ratios and of bed thickness, translated in capacity per unit area of the carrying table." Richardson and Langston3 have indicated results obtained with a dryer working with a fluidized bed. They used a vertical tube type of dryer, however, without the assistance of any mechanical energy, and without any lateral motion of the fluidized bed. The capacity of such a dryer is too limited for practical applications, since the speed of the acceptable air currents is held to the speed of fall of the particles involved. Capacities as low as 182 Ib of coal per hr per sq ft of dryer area are indicated. As stated by Richardson: "A basic limitation to a fluidised bed dryer is that the velocities of the gas must be held within a definite range; with velocities of 10 ft per second, all coal minus 6 mesh in size will be entrained, and the operation is then similar to that of a Flash dryer." A fluidized bed must be virtually static. The coal particles simply kept in suspension offer a minimum resistance to the flow of gases, insuring the most favorable conditions for rapid evaporation of surface moisture. However, very wet fine coal, i.e., over 12 pct of surface moisture, will be delivered in the forms of mud balls, or as a soggy, sticky mass, almost impossible to disperse, sticking and acting as a wet blanket on the deck. Strong currents of gases and wide deck perforations will be required to punch holes in the wet mass and gradually loosen and fluidize it. The mechanics of fluidizing a bed of coal in a gas medium for the purpose of obtaining the most efficient drying condition are entirely similar when the fluid used is water and the purpose is to break up and distend a bed of coal to be cleaned so that perfect stratification according to densities will be insured. Purely mechanical energy is used in the basket-type jig, water pulsations in the piston and in the Baum-type jigs. A combination of mechanical motion and of air pulsation offers the most efficient and favorable conditions. Entrained Condition The most critical factor to be considered in the design of a dryer employing the entrained condition technique is the speed of the hot gases to be circulated in the drying column. With insufficient gas velocity, excessive amounts of the largest sizes will drop to the bottom of the dryer column without being thoroughly dried. On the other hand, high gas velocity will cause degradation, dust losses, and high power consumption. Figs. 1 and 2, reproduced from Hanot,4 show the relative importance of speed and temperature for various sizes of particles. It can be seen, for instance, that to maintain in unstable equilibrium particles of 1/4-in. size in a gas current at 500°C, a speed of 30 meters per sec, or 6000 fpm, will be required. For % -in. particles an almost prohibitive speed of 45 meters per sec, or 9000 fpm, will be necessary. In practice, maximum gas velocities of 3000 fpm are recommended; since power increases as the cube of the velocity, it can be seen that beyond certain limits such dryers would not be economical. If the particles were moving at the same speed as the hot gases they would remain in the same

Jan 1, 1954

[Chairman ZAY JEFFRIES, Vice-chairman S. SKOWRONSKI, Chairman WILLIAM M, CORSE, Secretary Executive Committee J. R. FREEMAN, JR., Local Section G. E. JOHNSON R. S. ARCHER, Non-ferrous Data Sheets P. D. MERICA EDGAR C. BAIN, Journal Committee L. W. SPRING SAM TOUR, Papers Committee F. L. WOLF H. C. JENNISON, Membership Committee Local Section Committee J. R. FREEMAN, JR., Chairman R. J. ANDERSON, Cincinnati R L. DOWDELL, Minneapolis R. S. WILLIAMS, Boston G. H. CLAMER, Philadelphia W. A. SCHEUCH, Chicago R. F, Woon, New York Papers Committee S. SKOWRONSKI, Chairman F. H. DIx, JR.-Aluminum E. R. DARBY-Bronze C. S. WITH ERELL-Copper H. A. BEDWORTH-Brass W. K. FRANK-BRONZE F. W. HARRIS-Copper R. L. SUHL-Nickel H. M. ST. JOHN--Foundry Metallurgy R. S. DEAN-Theoretical Metallurgy]

Jan 1, 1928

By J. D. Sullivan, Chester R. Austin, J. L. Nunes

It is characteristic of most shales and surface clays that a bloated or vesicular structure is produced by burning to a sufficiently high temperature, usually about 150° to 200°F. above the normal maturing temperature used when making common brick of the same material. Early investi-: gators recognized this phenomenon and attributed it to the release or expansion of gases in the vitrified piece. A number of theories have been advanced on the source of the gas and the manner in which it is evolved, but none has been proved conclusively. T. E. Jackson&apos;s1 early theory that bloating was due to oxygen evolved by ferric oxide in forming ferrous oxide or ferrous silicate was never substantiated by - experimental work. Orton2 thought this explanation unlikely, as all clays should bloat at the same temperature, if this were true. He found that clays bloated in the range from IIoo° to 17oo°C. Also, many clays containing iron did not bloat at all, but fused. Orton also stated that oxida- tion of different types of carbon was a source of gas during burning of clay and should be expelled before vitrification was reached. Seger3 said that he had dissolved ferric oxide in glass with no apparent evolution of gas. Matson4 came to the conclusion that ferruginous clays burned &apos; to vitrification in an oxidizing atmosphere did not have the iron in a ferrous form. According to Wilson,= the gases responsible for bloating might be entrapped air, water, sulphur dioxide, carbon monoxide, oxygen, and hydrocarbons. He spoke of two causes of bloating: (I) incomplete oxidation below the vitrification temperature, and (2) decomposition of compounds and evolution of gases above the vitrification temperature. Decomposition of calcium sulphate was given as the principal example of the latter. Bleininger and Montgomery0 stated that if any time after vitrification began the evolution of gaseous matter was rapid enough so that pressure was produced within the clay, bloating was certain to take place, and a vesicular structure would be formed. They recognized that initial structure, rate of heating, kiln atmosphere, and many other variables affected bloating. Work done by the Emergency Fleet Corporation7 indicated that clays suitable for bloating should be high in compounds of metallic oxides, carbon, sulphur, sodium, potassium, or other equivalent compounds, which either act as a flux or give off gas. Orton2 studied the chemical status of the carbon, iron, and sulphur in clays during various stages of burning, using a Huron shale that bloated under oxidizing or reducing conditions. He found that only a small amount of sulphur remained in the clay and that it could be detected only by dissolving the clay in hydrofluoric acid; i.e., the sulphur was in combination with the silica. orton said that this sulphur was probably in the form of iron sulphide dissolved in the glass phase. The iron sulphide was not broken down by heating, but was dissolved in the basic slag or glass,

Jan 1, 1942

By J. D. Sullivan, Chester R. Austin, J. L. Nunes

It is characteristic of most shales and surface clays that a bloated or vesicular structure is produced by burning to a sufficiently high temperature, usually about 150° to 200°F. above the normal maturing temperature used when making common brick of the same material. Early investi-: gators recognized this phenomenon and attributed it to the release or expansion of gases in the vitrified piece. A number of theories have been advanced on the source of the gas and the manner in which it is evolved, but none has been proved conclusively. T. E. Jackson&apos;s1 early theory that bloating was due to oxygen evolved by ferric oxide in forming ferrous oxide or ferrous silicate was never substantiated by - experimental work. Orton2 thought this explanation unlikely, as all clays should bloat at the same temperature, if this were true. He found that clays bloated in the range from IIoo° to 17oo°C. Also, many clays containing iron did not bloat at all, but fused. Orton also stated that oxida- tion of different types of carbon was a source of gas during burning of clay and should be expelled before vitrification was reached. Seger3 said that he had dissolved ferric oxide in glass with no apparent evolution of gas. Matson4 came to the conclusion that ferruginous clays burned &apos; to vitrification in an oxidizing atmosphere did not have the iron in a ferrous form. According to Wilson,= the gases responsible for bloating might be entrapped air, water, sulphur dioxide, carbon monoxide, oxygen, and hydrocarbons. He spoke of two causes of bloating: (I) incomplete oxidation below the vitrification temperature, and (2) decomposition of compounds and evolution of gases above the vitrification temperature. Decomposition of calcium sulphate was given as the principal example of the latter. Bleininger and Montgomery0 stated that if any time after vitrification began the evolution of gaseous matter was rapid enough so that pressure was produced within the clay, bloating was certain to take place, and a vesicular structure would be formed. They recognized that initial structure, rate of heating, kiln atmosphere, and many other variables affected bloating. Work done by the Emergency Fleet Corporation7 indicated that clays suitable for bloating should be high in compounds of metallic oxides, carbon, sulphur, sodium, potassium, or other equivalent compounds, which either act as a flux or give off gas. Orton2 studied the chemical status of the carbon, iron, and sulphur in clays during various stages of burning, using a Huron shale that bloated under oxidizing or reducing conditions. He found that only a small amount of sulphur remained in the clay and that it could be detected only by dissolving the clay in hydrofluoric acid; i.e., the sulphur was in combination with the silica. orton said that this sulphur was probably in the form of iron sulphide dissolved in the glass phase. The iron sulphide was not broken down by heating, but was dissolved in the basic slag or glass,

Jan 1, 1942