Search Documents

By W. L. Connell, O&apos

The properties of some heavy liquids which can be used in sink-float separations are discussed with major emphasis being given to the halogenated hydrocarbons. Data are presented on density, viscosity, thermal characteristics and the effects of moisture and temperature on the corrosiveness of the liquids towards various materials of construction. The toxicity of these materials, the hazards involved in handling them, and the procedures for handling them safely are also discussed. True liquids have certain advantages over colloidal suspensions for sink-float separation of minerals which makes their use especially advantageous when close separations, fine particle sizes or water-soluble minerals are to be treated. For best separating results, the medium should have an easily controlled, uniform, stable density. Here, true liquids have the advantages of allowing closer control of density and of not requiring agitation to maintain a uniform den- sity in the equipment. Low viscosities are desired in a separating liquid so that rapid separations of fine material can be made. Many liquids have lower viscosities than the colloidal suspensions at operating gravities of 1.4 to 5.0. For economic reasons and to prevent contamination of the product, the separating medium must be easily and completely removed from the ore. Normally, true liquids must be more completely removed than the cheaper suspensions and thus cause more problems in this area. The fact that the medium should not react with the minerals, air, water or the common materials of construction limits the choice of liquids which can be used, but many are available which are sufficiently stable. A more serious objection to the use of true liquids is that many of them present a toxic hazard to operating personnel and users of the product. Most true liquids are toxic to some extent, but modem knowledge of toxicity allows us to recognize the hazards inherent in handling them and enables us to design around them. Three types of true liquids are available for this use: 1) Halogenated hydrocarbons cover the gravity range from 1.2 to 3.3. They are generally more volatile and less viscous than the other liquids.

Jan 1, 1963

By C. C. Wright, T. S. Spicer

A characteristic property of bituminous coal is that upon being heated the coal becomes plastic, evolves volatile gases, and finally solidifies into coke. This fundamental characteristic is of utmost importance and is utilized in the production of the high-temperature coke upon which the steel industry is so dependent; but from the standpoint of operation in the domestic underfeed stoker this coking tendency seriously interferes with efficient combustion. When the coke formed has too strong a structure, certain difficulties result, such as low rate of burning, slow response to heat demand, and, in extreme cases, extinction of fire. The plastic mass prevents uniform distribution of air through the fuel bed and, with strongly coking coals, large dense pieces of coke are produced which have much less reacting surface than was possessed by the original coal. In both ignition and combustion of solid fuels, the extent of the reacting surface is an accelerating factor. Poor combustion permits a surplus of fuel to accumulate in the furnace because the rate of feed and the rate of combustion are not in equilibrium, and this produces an unbalanced condition detrimental to continued automatic service. In order to bum strongly coking coals satisfactorily in a conventional stoker during the three requisite types of operation—continuous, intermittent and hold-fire, frequent attention is necessary. Domestic stokers are defined by the industry as residential stoker heaters that burn 60 lb. of coal or less per hour. With a few exceptions, these units employ the underfeed principle of combustion in which both air and coal move in the same direction up and through the fuel bed. Domestic combustion equipment has difficulty in meeting the problems presented by the several variations in ash and volatile matter, in ash-clinkering tendencies, in coking properties, and in the particle size of bituminous coals. The work of Bituminous Coal Research Inc. at Battelle Memorial Institute has shown that, of these, coking characteristics and the clinkering tendencies have the greatest effect upon the operation of the conventional clinkering type of stoker. Typical coke formations in a clinkering type of underfeed domestic stoker are illustratcd in Fig. I, which shows (A) the ideal fuel bed obtained with a noncoking or free-burning coal; (B) the type of fuel bed formed with a coal that produces a weak coke; and (C) the type of fuel bed obtained with a strongly coking coal. C is characteristic of the fuel bed developed when the average Pennsylvania bituminous coal is burned in an underfeed stoker of conventional type. It is apparent from these pictures that the formation of coke trees will seriously interfere with the efficient automatic combustion of Pennsylvania bituminous coals.

Jan 1, 1942

By T. S. Spicer, C. C. Wright

A characteristic property of bituminous coal is that upon being heated the coal becomes plastic, evolves volatile gases, and finally solidifies into coke. This fundamental characteristic is of utmost importance and is utilized in the production of the high-temperature coke upon which the steel industry is so dependent; but from the standpoint of operation in the domestic underfeed stoker this coking tendency seriously interferes with efficient combustion. When the coke formed has too strong a structure, certain difficulties result, such as low rate of burning, slow response to heat demand, and, in extreme cases, extinction of fire. The plastic mass prevents uniform distribution of air through the fuel bed and, with strongly coking coals, large dense pieces of coke are produced which have much less reacting surface than was possessed by the original coal. In both ignition and combustion of solid fuels, the extent of the reacting surface is an accelerating factor. Poor combustion permits a surplus of fuel to accumulate in the furnace because the rate of feed and the rate of combustion are not in equilibrium, and this produces an unbalanced condition detrimental to continued automatic service. In order to bum strongly coking coals satisfactorily in a conventional stoker during the three requisite types of operation—continuous, intermittent and hold-fire, frequent attention is necessary. Domestic stokers are defined by the industry as residential stoker heaters that burn 60 lb. of coal or less per hour. With a few exceptions, these units employ the underfeed principle of combustion in which both air and coal move in the same direction up and through the fuel bed. Domestic combustion equipment has difficulty in meeting the problems presented by the several variations in ash and volatile matter, in ash-clinkering tendencies, in coking properties, and in the particle size of bituminous coals. The work of Bituminous Coal Research Inc. at Battelle Memorial Institute has shown that, of these, coking characteristics and the clinkering tendencies have the greatest effect upon the operation of the conventional clinkering type of stoker. Typical coke formations in a clinkering type of underfeed domestic stoker are illustratcd in Fig. I, which shows (A) the ideal fuel bed obtained with a noncoking or free-burning coal; (B) the type of fuel bed formed with a coal that produces a weak coke; and (C) the type of fuel bed obtained with a strongly coking coal. C is characteristic of the fuel bed developed when the average Pennsylvania bituminous coal is burned in an underfeed stoker of conventional type. It is apparent from these pictures that the formation of coke trees will seriously interfere with the efficient automatic combustion of Pennsylvania bituminous coals.

Jan 1, 1942

By S. M. M. Safvi, A. Jowett

Small-scale continuous flotation tests are described in which the influence of 1) pulp density and 2) feed rate on the rate of flotation are investigated. The results provide further evidence of first-order kinetics for flotation and indicate that tests at different feed rates provide a particularly simple method of determining rate constants. Flotation kinetics are discussed in general terms. Over a period of many years numerous research workers have studied the rate of recovery of valuable materials from flotation pulps with a view to deter-mining the mechanism of the froth flotation process. Froth flo ation is fundamentally a collision process involviug at some stage collision and then mutual attachment between air bubbles and mineral particles. It is possible to draw analogies therefore between the flotation process involving mainly macroscopic particles and the ordinary processes of chemical reaction kinetics involving collisions between atoms, molecules and ions. By adopting this analogy we may postulate a general equation representing the kinetics of the flotation process: -dC/dt =K.CC ,Aa (1) The rate constant, K, will be a complex function involving reagent concentrations, particle and bubble sizes, induction times and no doubt flotation cell design. However, these are factors which can be kept constant in any series of experiments, permitting investigation of the exponents a and c, which determine the order of the reaction occurring in flotation. The various research investigations carried out so far have all aimed at evaluating a and c and in the majority of cases only since the concentration of air has usually been kept constant in a series of tests, so that a relationship of the following type has been investigated: -dC/dt = K1 Cc (2) The techniques of both batch testing and continuous testing have been used to investigate this relationship. The technique of continuous testing, in which steady-state conditions are established, permits direct investigation of the above equation. In the case of batch testing, C is decreasing continuously

Jan 1, 1961

By Charles H. White

Discussion of the paper of A. L. Sweetser, Tress., xxxviii., 236. CHARLES H. WHITE, Harvard University, Cambridge, Mass. (communication to the Secretary*) :-Those interested in leaching-processes gladly welcome contributions on either laboratory-tests, such as are reported by Mr. Sweetser, or mill-tests made on larger quantities of ore; and especially valuable are such reports, even with negative results, if the methods adopted are the outgrowth of an intimate knowledge of the conditions to be met. It seems very desirable, therefore, that as complete details as possible be given in reporting on such tests, particularly with respect to the character of the ore under examination. The questions of prime importance in the sampling of ore and in the making up of charges for laboratory-tests are those respecting its grade and uniformity. In Mr. Sweetser's paper the first of these questions is answered definitely, but the answer to the second, although apparent on inspection of the results, might be more strongly emphasized with advantage, since it is only on account of the extreme uniformity of the ore that the satisfactory results obtained could have been expected. It seems advisable to call attention to the fact that for average ores, and more particularly for uneven, or 11 spotted ores, the quantities used by Mr. Sweetser are not usually regarded as sufficient to insure satisfactory results. Let us examine the method somewhat in detail. The ore was crushed to pass a 5-mesh screen, and a sample of 45 lb. was taken out for assay and tests. The diameter of the largest grain of this ore, according to Richards,1 was 2.67 mm.-assuming here, as in the following cases, that the wire of the screen was of the largest size used for the purpose, thereby giving any possible advantage in this respect in favor of the method. The table in Richards's book, p. 852, shows that 45 lb. is a sufficient quantity for a fair sample with uniform ores, but not sufficient

Jan 7, 1908

By G. V. Jere, V. Krishnan, C. C. Patel

Standard free energy and standard enthalpy changes as a function of temperature have been calculated for the chlorination reactions of different oxides constituting columbite and tantalite. The tallies of standard lee-energy change (F) indicate the possibility of pvefeential chlorination of different oxides but the ease 0.f chlorination of columbium pentoxide at about 250°C and the chlorinating tendency of columbium pentachloride in promoting the chlorination of tantalum and other metal oxides, p7-evetzt the separation of columbiu?n and tantalum from other oxides and pom each othel.. It is likely that low temperatuves of chlorination and continuous 1err2oval of columbium pentachloride from the ..eaction zone may help partial separation of columbium from tantalum as well as from titanium. The standavd enthaply change (AH?) values shotr that 1ou.-temperature chlorination around 300" to 500°C is likely to sustain the chlorination , without external heating. COLUMBIUM (niobium) and tantalum metals, their alloys and interstitial compounds are finding extensive uses in nuclear reactors and high-temperature equipment.la-3 These metals also find uses in chemical process plants, electrical rectifiers and capacitors and as "getters" in electronic tubes.la With the development of Kroll process of reduction of volatilized titanium tetrachloride by magnesium for the production of titanium metal, chlorine metallurgy is receiving greater attention. Chlorine metallurgy has several advantages, the foremost amongst them are: the ease of chloride formation, separation of the different constituents of minerals by selective chlorination, and the reduction of the chlorides in vapor phase to the respective metals. Recently, Si-bert, Kolk, and Steinberg4 have considered a number of methods for the preparation of columbium metal and the most promising is found to be the halide reduction. Since the minerals columbite and tantalite are comparatively abundant in nature, the future of the metallurgical processes depends on the utilization of these minerals for the production of columbium and tantalum chlorides by chlorination. In this paper, an attempt has been made to interpret thermodynamically the chlorination of individual oxides constituting columbite and tantalite, with the help of the recent thermodynamic data.5-8 For this purpose, standard free energy and standard enthalpy changes of the chlorination reactions of the oxides with chlorine, both in absence and presence of carbon as the reductant, have been calculated as a function of temperature and represented graphically. Similar calculations for the reactions employing carbon tetrachloride and carbonyl chloride as chlorinating agents have also been incorporated in this paper. REPORTED WORK ON CHLORINATION Cuvelliezg has patented a process for the separation of columbium and tantalum from their concentrate, wherein 75 pct Cb05 is claimed to be chlorinated at 1050°C in the course of 7 hr using chlorine or chlorine containing nonreducing gases, the products of reaction being CbC1, or CbOC1,. At this temperature, Ta,05 is claimed to remain unaffected. It is further claimed1° that at higher temperatures, the proportion of Ta205 chlorinated increases while that of Cb205 diminishes. During the studies on the action of chlorine on individual metal oxides, Kangro and Jahn" have observed that Ta,05 is not chlorinated even at 1200" in the stream of chlorine, while 75 pct of Cb,05 is converted into CbOC1, around 900 to 1100°C. The chlorination of Cb205 by chlorine in the presence of carbon, investigated by Lind and Ingle,' and

Jan 1, 1962

By Ernest Darby

IF the correct balance between fuel and air is maintained in an open-flame furnace,1 little chemical action may be expected between the products of combustion and the metal being melted. Physical changes in the metal are the object of the melting operation, and indirectly, under certain conditions, may be the cause of subsequent chemical actions. If sufficient heat has been introduced into the metal to bring about the change from the solid phase to the liquid phase, and still further from the liquid to the vapor phase, the metal vapor in all probability will be carried from the furnace by the exhaust and rapidly combined with the oxygen of the outside air. The charge being melted in the furnace may contain elements which are chemically inactive at normal temperatures but which will form compounds at the elevated temperatures of the metal bath, or even at a lower degree. Such indirect chemical actions are very confusing and often lead to incorrect conclusions regarding furnace atmospheres. In the open-flame furnaces used in the melting of bronze, the furnace atmosphere is spoken of as being either neutral, oxidizing or reducing in its effect upon the metal. A neutral atmosphere, as mentioned, is generally considered as the atmosphere of the furnace that will produce melted bronze, neither oxidized nor gassed. It is in effect an atmosphere which is not directly the cause of any chemical action. In such an atmosphere absolutely pure metals may be melted and poured without the absorption of gases or the formation of metallic oxide. The metal has undergone a simple, physical change.

Jan 1, 1930

By Larry D. Hartzog

PANELISTS Paul Chamberlin, Nerco Minerals Jim Gourdie, Goldfield Mining Corp. Roger Leonard, Cyprus Northumberland Mining Co. Eric Daniels, Tenneco Minerals John Dasher, Consulting Metallurgist Bob Shoemaker, San Francisco Mining Associates Larry Hartzog, Bechtel Civil and Minerals, Inc.

Jan 1, 1984

By B. E. Warren

Jan 1, 1965

By Donald F. Kennedy

During the past several years Climax Molybdenum Co. has been engaged in testing various types and sizes of hollow drill steel. The majority of tests have been on 7/8-in. hexagon st.ee1, inasmuch as it represents approximately 70% of total drill steel consumption at the Climax operation. Prior to December 1960, tests on 7/8-in. hexagon drill steel were conducted on steel with a forged collar and, in most cases, with a threaded bit connection. Through these tests and research, some improvement in steel life was achieved by making changes in heat treatment, design and alloying constituents. However, during that month, research and testing commenced on a rubber collar which was designed to replace the forged collar on 7/8-in. hexagon drill steel. Manufactured by the LeRoi Div. of Westinghouse Air Brake Co.. the collar. is very simple in design, consisting of a 1 ½ -in. diam steel cylindrical sleeve 2 in. long, containing a bonded rubber insert and attached to the steel with an epoxy cement

Jan 8, 1962

By George J. Simchuk

Selection of an applicable stripping method and the subsequent determination of appropriate sizes of selected equipment are discussed. The case in point is Utah International, Inc.'s Goonyella mine located in central Queensland, Australia. A detailed study of the various types of stripping methods now practiced throughout the world led to the conclusion that large draglines would be the logical choice for Goonyella. The optimal size of dragline was then determined by first designing a series of cut diagrams using an array of machine and pit geometries followed by a cost comparison of the various sizes of machines, in terms of their effective spoil radius. A dragline with a 51-cu-yd bucket was determined to be of optimum size. Further calculations, incorporating total overburden moved from both the highwall and spoil sides, required that four drag lines, two equipped with 40-cy-yd buckets and two with 54-cu-yd buckets, be used to satisfy the stripping requirements at Goonyella.

Jan 1, 1973

By Walter V. Knopp, Laurence Delisle

INTRODUCTION THE aim of this work was the preparation of nickel-steels from elemental metal powders by powder metallurgy techniques. It was known that plain carbon steels could be made from a mixture of iron powder and graphite and that the effect of carbon on iron in powder form was of the same nature as that produced in fusion metallurgy. The problem in making nickel steels from elemental powders consisted therefore in finding out whether sufficient diffusion of the nickel and other incidental metals normally present in such steels could be induced in the solid state to modify the properties of plain carbon steels made from powders and produce the beneficial effect of alloying. The composition selected originally was that of an S.A.E. 2330 steel. Metal powders, in the proportion corresponding to that composition, were mixed with graphite, pressed, and heated at different temperatures for different periods of time, to produce bonding of the metal particles and mutual diffusion of the various elements without melting. Temperatures up to 1325°C and sintering periods as long as 6 hr were first investigated because it was expected that such conditions would produce maximum diffusion with an accompanying improvement in the properties of the alloy. It was found that, although diffusion proceeded to a large extent under the conditions investigated, it would not be complete unless sintering were carried out at a high temperature for much longer than 6 hr. Relatively high temperatures and long sintering times are objectionable from a practical point of view, particularly when a low cost material is to be produced, because they necessitate the use of special, costly equipment. Work could be done to improve the diffusion of iron and nickel by changing conditions other than the sintering temperature and time, i.e., finer primary or alloy powders could be used. However, a marked change in the properties of the steel had been observed even with only partial diffusion. It was thought, therefore, that instead of trying to improve the diffusion, advantage might be taken of its incompleteness to produce a special structure consisting, in the unquenched condition, of a hard constituent, rich in nickel, dispersed in a tough pearlitic matrix. Steels with such a structure, not readily obtainable by fusion, should have desirable mechanical properties. Besides, it should be possible to prepare them from elemental powders under economical conditions. This latter alternative was therefore adopted for the second phase of this work. This report is divided into four parts: 1. General Procedure. 2. Effect of Sintering Temperature. 3. Effect of Varying the Nickel Content. 4. Effect of Alloying Elements. GENERAL PROCEDURE The general technique of cold pressing as used in powder metallurgy was applied.

Jan 1, 1948

US 4,181,520 - Direct reduction of iron oxide ore to sponge iron in a rotary kiln. Ore is fed into the kiln along with coal briquettes and passed through a preheating zone and then a reducing zone countercurrent to the flow of a kiln atmosphere which includes air or other oxygen-containing gas. The agglomerated coal is heated at such a rate that it disintegrates into fine particles in the preheating zone. The coal is largely recovered for reuse, while reduction is effected with a reducing flame rather than the coal. G. Reuter and W. Schnabel, assigned to Metallgesellschaft AG. Jan. 1, 1980. 6 pp. (75-36). Filed- 10-19-78 (952,870). Priority: West Germany, 1-14-75 (2,501,182). Same: British 1,532,969, dated Nov 22, 1978.

Jan 1, 1982

By Charles S. Barrett, Robert F. Mehl

It is generally understood by workers in the field of the crystal structure of metallic alloys that terminal solid solutions are of two types, the substitutional and the interstitial. In reviewing the literature, the work of Weissl on the crystal structure of the alpha copper-tin alloys was encountered, in which a new type of terminal solid solution was proposed. In brief, Weiss' findings showed that the density of the alloys calculated from the side of the unit face-centered cube on the assumption of simple substitution—that is, with four atoms to the unit face-centered cell—was much higher than the density measured directly. It was suggested that the assumption of four atoms to the unit cube is not valid for these alloys, and that each unit cube contained less than four atoms; in other words, that one tin atom replaces more than one copper atom, leaving some atomic positions unoccupied. Such a structure, if verified, would have far-reaching significance in the study of the crystal structure of metallic alloys. It would indicate a complexity in terminal solid solutions not hitherto suspected and might encourage work leading to the discovery of other alloys of the same type, and perhaps to types intermediate between it and the two recognized types. It is of importance, therefore, to reinvestigate these alloys with respect to the type of solid-solution structure obtaining therein. Materials and Experimental Method The alloys were prepared from electrolytic copper cut directly from the cathode and the high-purity tin furnished by the U. S. Bureau of Standards for the calibration of thermocouples. No analyses for impurities of these materials or of the finished alloys were made, since such impurities as might be present could have only a wholly inappreciable effect upon the data obtained and the conclusions drawn. The alloys were made by melting the weighed copper charge in a graphite crucible under a KCl-LiC1 flux with later additions of NaC1, using induction heating. When the copper was melted the weighed portions of tin were

Jan 1, 1930

By Robert B. Kistler, Ward C. Smith

The borate industry is one of the few sectors of the mining and mineral-processing industry which the United States still dominates. Since about 1927, the United States has supplied over half of the world's total boron and borate raw materials, and many of the chemical derivatives as well. Chiefly responsible for this record are companies producing sodium borates from two large deposits in southern California, at Boron (Kramer) and Searles Lake. The sodium borates, or products derived from borax and borax-containing brines, are the preferred borates for industry because they are soluble in water and combine readily with most other chemicals. Calcium borates (or sodium-free compounds) are required for certain end uses, but in general, nonsodium borates are used only where borax is not avail- able. During the past hundred years, the use of boron compounds throughout the world has risen from a few tons per year to the equivalent of about a million tons of B2O3. Leadership in supplying borates has shifted from country to country and from region to region during this period, generally as the result of the development of newly discovered deposits that were better in quality, more accessible, or more economically exploitable than previous sources (Table 1). Primary Products and End Uses The principal borate products offered by primary producers in the United States are listed in Table 2. In general, these products are utilized worldwide by almost all consumers, regardless of the original source of the primary borates. In the United States, the primary borates all originate in southern California. Colemanite is produced as crude or processed crude ore from the Death Valley area and is utilized by the fiber glass and ceramic industries without further treatment. Production from Searles Lake, Calif., is from brines that are processed in chemical plants where borax and other compounds are recovered and the principal borate products are produced. At Boron, Calif., the world's leading producer is mining a deposit of mineral borax and operating a chemical refinery. The mineral borax is mined together with included clay, and refined borax or "lo-mol" is one of the refinery products. The mineral and the chemical compound are identical, Na2B4O7- lOH2O. In addition to ship- ping all major refined borate products from Boron, the company ships semiprocessed ore concentrates to treatment plants elsewhere.

Jan 1, 1975

By Lawrence Addicks

(San Francisco Meeting, September, 1915) THROUGH the courtesy of Dr. James Douglas I am permitted to give, a summary of some of the results obtained in leaching slimes tailings in a series of experiments conducted under my direction at Douglas, Ariz.. during the past year. While the test run for which the data are given deals with a particular case, much of the work is general in its application and may therefore be of interest. This work was done upon the ores of the Burro Mountain Copper Co. A description of the geology of the district will be-found in the paper by R. E. Somers published in the May, 1915, Bulletin of the Institute. The mineral is pyrite and chalcocite very finely disseminated throughout the gangue and a characteristic of all the ores is the large amount of alumina present. A representative analysis of the particular ore under consideration would be about as follows: Cu, per cent 2.35 S, percent 3.0 Ag, ounces per ton 0.05 CaO, per cent 0.5 Au None K202, per cent 4.0 Fe, per cent 1.5 SiO2, per cent 70.0 A120,, per cent 13.0 The leaching of the ore direct was early dismissed from consideration for the following reasons: 1. The ore would have to be quite finely crushed to liberate the mineral for leaching; concentrating after crushing would cost but a few cents a ton; and a higher total recovery would result from leaching tailings rather than ore. 2. Rough concentration would yield a suitable material for roasting to make sulphur dioxide or sulphuric acid in connection with the leaching scheme. 3. Such a program put the question of cost vs. recovery on a basis where flotation and discarding of tailings were directly comparable.

Jan 8, 1915

By L. H. Simons, H. H. Spain

I NT RODUCTION Theory indicates that linear water-floods should exhibit scaling and stabilization properties in both oil-wet and water-wet porous media'. Experimental verification of these proper-ties in oil-wet media was obtained some time ago', and more recently, Perkins', employing a high permeability unconsoli dated sand and a low oil-to-water viscosity ratio, has obtained flooding data in a water-wet medium which follow the pattern of scaling and stabilization. Also, Root and Calhoun3 have found similar trends in the displacement of gas by liquids from unconsolidated sands. In general, however, the experimen-tal evidence appears still somewhat conflicting since scaling and stabilization of water floods in water-wet media has not been observed in most of the studies to date'.".'. The purpose of this paper is to provide a more comprehensive picture of waterflood behavior in water-wet media and to corroborate the validity of the scaling and stabiliza-tion concepts. The need for differentiating between the intrinsic nature of water-oil displacements inside a porous medium and perturbating secondary end effects is discussed, pertinent experimental procedures are outlined and the results of flooding tests conducted at low and at high oil-to-water viscosity ratios on con- solidated, water-wet Alundum cores are analyzed. END EFFECTS IN WATER-WET MEDIA Outlet End Effects The peculiar feature of the outlet end effect in water-wet cores is that it not only results in an excessive wetting phase saturation at the outflow face,'.' but that it also retards the moment of water breakthrough: i.e., causes an undue delay in the appearance of water in the produced effluent. Conditions existing in a water-wet core when water first arrives at the outflow face are schematically shown in Fig. 1. At this flooding stage the saturation distribution, Fig. la, has not yet been distorted by the outlet end effect. A water-invaded pore at the outlet core face, opening into the oil-filled void space between the end of the core and the end plate of the flooding cell, is illustrated in Fig. lb. The curvature of the water-oil interface is concave toward the outlet, and the pressure on the water side of the interface is lower than on the oil side by an amount equal to a certain capillary pressure (Fig. lc). Before the water (of this particular pore) can be produced from the core, it is apparent that the pressure in the water phase must exceed that in the oil outside the core. Accordingly. when water first reaches the outlet face, it will not leave the core but will accumulate inside, and only oil will be produced. Eventually, as the water injection is continued. sufficient pressure is built up in the water to reverse the curvature of the interfaces in the outlet pores, and only then will water be produced from the core. This stage, illustrated in Fig. 2. corresponds to the conventional "water breakthrough" observed in flooding experiments. For purposes of discussion, it is convenient to distinguish between the flooding stage at which water first arrives at the outlet face of a core (Fig. 1) and the stage at which water is first produced from the core ( Fig. 2). The former will be referred to as "water arrival" and the latter water breakthrough. In oil-wet media

By Waldemar Lindgren

THE following pages present data accepted by many geochemists and geologists regarding the succession of minerals and the temperatures of formation in ore deposits affiliated with igneous rocks. They also present the individual views of the author on the composition of the solutions that were active and on the mode of deposition. He does not regard these views as speculations or hypotheses but as forming a well motivated and consistent theory. It is not certain, however, that all investigators will subscribe to them.

Jan 1, 1936

By F. A., King

THE problem of the proper size and capacity of the open-hearth furnace has been a predominant issue ever since its inception some sixty years ago. The original furnaces, built in 1868 at Landore, England, were only to 3 to 4 tons capacity, and from' this there has been a steadily increasing and almost uniform rate of expansion until furnaces producing 300 tons are in successful operation today. At the end of the first half of this 60-year period, or about the year 1900, 50-ton furnaces we're common. Up to this time the problems of expansion had been largely those relating to suficient capital and the engineering development of larger units. But as 75, 100-ton and larger furnaces were proposed apprehension grew and other questions assumed leading consideration.

Jan 1, 1928

By S. H. Chauvenet

HARRISBURG is situated on the Pennsylvania Railroad, one hundred and five miles from Philadelphia, two hundred and forty-eight miles from Pittsburgh, and ninety miles from Baltimore, and has running through it the Pennsylvania, Northern Central, Philadelphia and Reading, and Cumberland Valley Railroads, and the Pennsylvania Canal. Surrounded by a thickly settled farming country, from which to draw native labor, within easy distance of anthracite and bituminous coal, with ores and limestone near at hand, and with the Susquehanna River as a never-failing water supply, Harrisburg has advantages for manufacturing which warrant the investment of the capital that has already been made, and has a future as a manufacturing city second only to Pittsburgh and Philadelphia. THE PENNSYLVANIA STEEL COMPANY, L. S. BENT, SUPERINTENDENT. The works of this company, the largest in Harrisburg, lie between the Pennsylvania and the Philadelphia and Reading Railroads, on. the Pennsylvania Canal, and are essentially devoted to the manufacture of Bessemer steel rails. Capital stock, $2,000,000; invested in business, $5,000,000; wages per month, $80,000; employs 2000 men; capacity, 100,000 tons of rails per year, which is being increased to 130,000 tons. The plant, as it now stands, comprises five Bessemer converters, two 7-ton and three 8-ton converters, two 15-ton open-hearth furnaces in operation, and two 30-ton open-hearth furnaces in course of construction, one blooming mill, one rail mill, seven steam hammers, two blast furnaces in operation, two blast furnaces in course of construction, foundry, pattern $hop, machine shop, blacksmith shop, and frog shop, and merchant mill in course of construction. Bessemer No. 1 was built in 1865, with two 7-ton converters, 2 spiegel cupolas, 3 feet diameter, and 3 iron cupolas 6' 6" diameter,

Jan 1, 1882