Search Documents

By H. T. Green, R. M. Brick

True stress-strain data on alloys of pure iron with up to 2.4 pct Al were obtained in the temperature range +100° to —185°C. Alumi-num was found to reduce yield and flow stresses of iron at low temperatures but to have little or no effect on ductility. The effects of temperature and composition on strain hardening are discussed. SEVERAL independent studies of the behavior of high purity iron binary alloys at low temperatures are now in progress in attempts to evaluate systematically the variables affecting the low temperature brittleness of ferritic steels. This paper reports the results of one such investigation in which the tensile properties of aluminum and aluminum plus silicon ferrites were measured from 100" to —192°C. True stress-natural strain data have been obtained in order to evaluate as many as possible of the parameters which describe the behavior of the materials involved. In comparable studies at the National Physical Laboratory in England, iron and iron alloys of high purity have been produced' and tested at subat-mospheric temperatures.' True stress-natural strain curves were obtained there also. The purest iron contained 0.0025 pct C and 0.001 pct O and N. Even this, as normalized at 950°C following hot rolling, showed little ductility at -196°C. The grain size was ASTM No. 3, and the room-temperature yield strength was 17,800 psi (which seems too high for pure iron). Some of the NPL irons contained considerably more oxygen and demonstrated intergran-ular fracture at —196°C. The authors2 carefully differentiated between intergranular fractures associated with excessive oxygen content and transcrys-talline cleavage with little ductility encountered at —196°C in the purer material. The cleavage stress was half again as great as that associated with inter-granular fracture. Test Material, Preparation, and Procedures Of a number of Fe-A1 alloys produced, eight were considered to be sufficiently pure for testing. Partial chemical analyses (Table I), low observed yield points, and high ductilities indicate these alloys to be comparatively pure for vacuum-melted irons of sizable ingots, 5 Ib or more. To produce the binary Fe-A1 alloys, electrolytic iron was melted in air, cast into slabs, and rolled to strips 0.010 in. thick. These strips, joined into a continuous ribbon and wound into 2 1/2 in. diameter spools, were subjected for four weeks to a moving atmosphere of purified dry hydrogen in a stainless-steel tube at 1050" to 1150°C. Charges of these spools were melted in beryllia crucibles under good vacuums (1 micron), and aluminum (99.97 pct Al) was added to the melts. Compositions of these alloys are recorded in Table I. The ingots were hot forged and then cold rolled at least 65 pct to 3/8 in. rods which were vacuum annealed to the desired grain size, approximately ASTM No. 4, prior to machining into tensile test bars. All tensile specimens had gage sections 1 in. long, with a fillet of 1.5 in. radius to the shoulder. Gage diameters were 0.250 in, except for a few rods where additional cold work required use of a 0.200 in. gage section. After machining, 0.002 in. was removed from the gage diameter using 240, 400, and 600-grit metallo-graphic papers. The final polish with 600 grit left the fine scratches running in the longitudinal direction. By this means, surface metal strained during machining was removed. A few specimens heat treated after machining were similarly reduced 0.004 in. to remove any material affected chemically by the atmosphere during heat treatments, as is discussed in a later section. Tensile tests of the eight alloys at constant temperatures from +100° to —185°C were performed in apparatus which has been described." The essentials include a double-walled insulated metal vessel which contained the liquid heat-transfer medium surrounding the test specimen. A constant temperature was maintained by means of a pyrometer which regulated the pressure of dry air driving liquid air through a copper coil. Temperature variation was less than ±2°C during a specific test. For axial straining, two lengths of case-hardened chain, terminating in simple shackles, loaded the specimen through threaded grips. The lower grip bar passed through a hole in the bottom of the test vessel to which it was joined by a thin-walled

Jan 1, 1955

By Richard L. Ashbrook, John F. Wallace

Several high-temperature eutectics of cobalt and nickel alloys were modified by small additions of selected elements. Thes-e alloys were compared to unmodified melts for microstructural variations. A few modified compositions were selected on the basis of structure and their tensile and stress-rupture behavior determined. The results of stress-rupture tests in air at 1800 F and room-temperature tensile tests of four high-temperature eutectics showed modification capable of producing substantial improvements in properties. The microstructures were altered and mechanical properties improved by: a.) dispersing a subordinate phase more uniformly throughout the matrix; b) replacing large continuous -network or platelike constituents with small equiaxed discontinuous phases; and c) by forming new, finely divided phases. tHE term "modification" is most commonly used to describe the refinement in microstructure of the Al-Si eutectic that occurs as a result of rapid cooling from the melt or on slow cooling after treatment with small amounts of sodium.1 "Modification" has also been used to describe the change from flake to spheroidal graphite in the austenite-graphite eutectic of cast iron.2 This change of graphite shape is accomplished by small additions of cerium or magnesium.3 Other systems have also been shown to be capable of modification, for example: Pb-Sn by copper;4 Al-Cu by sodium;5 Al-Mn by sodium;5 and Pb-Sb by aluminum.5 Although modification of Al-Si alloys and cast irons is usually accompanied by improved mechanical properties, a general definition of modification has been suggested to include the effect of small quantities of impurity elements on the microstructures of all eutectic alloys, regardless of the effect on the mechanical properties.6 In this paper, the term "modification" is employed in a broad sense to include the formation of third phases or even the supplanting of one of the binary eutectic phases by a third phase. The mechanism of modification, as for any solidification phenomenon, must be considered primarily in terms of nucleation and growth. Although both nuclea-tion and growth mechanisms are required to explain all the phenomena observed in connection with the solidification of modified eutectics, various investigators have usually favored one or the other.7"16 It has been shown that modification of a binary eutectic can be effected by addition of a solute element that has greatly different distribution coefficients or k values in the two phases of the eutectic. Under these conditions, differences in the temperatures at the solid-liquid interfaces of the two phases retard the growth of one phase with respect to the other.4 It has also been shown that increased undercooling favors a transition from a rodlike eutectic to a globular eutectic.17 A mechanism proposed for the transition from lamellar to rodlike eutectics depends on the concept of constitutional super cooling.18 The modification of eutectic alloys may be of interest for high-temperature service as well as at room temperature. Although "high-temperature eutectic alloys" may appear to be a contradiction in terms, many eutectic systems, including those studied in this work, have melting points in excess of 2400°F. One of the mechanisms by which high-temperature alloys are strengthened is dispersion of a relatively brittle phase such as an oxide, carbide, or an inter-metallic compound throughout a ductile matrix. For a given volume fraction of dispersed phase, strength is increased by decreasing the size and spacing of the dispersed particles.19'20 Furthermore, room-temperature ductility may also be increased by changing the shape of a brittle dispersed phase from platelike to equiaxed or spheroidal.8 Overaging and redissolving of the secondary phase limit the maximum temperature to which precipitation-hardened alloys can be used. However, in a binary eutectic system, both phases coexist up to the melting point. Although all eutectic structures are not completely stable,21 a dispersion-hardened cast high-temperature alloy might result if a fine distribution of one of the eutectic phases could be obtained during solidification. An additional reason for interest in eutectic alloys is their excellent castability.22 Since eutectic alloys, like pure metals, freeze at a single temperature rather than over a range of temperatures, their castability is superior to solid-solution alloys with long liquidus to solidus ranges. The purpose of this research was to study the effects of small solute additions on the microstructure and mechanical properties of a number of high-melting-point eutectic compositions.

Jan 1, 1967

By C. W. Stratford

[During the last few years, the necessity for development work has been generally recognized by executives throughout the oil industry, resulting in greatly accelerated progress and the adoption of many noteworthy improvements in refining methods and equipment. Several years ago, the Associated Oil Co. decided to improve distillation methods with the object of reducing refining costs. This extremely interesting work was entrusted to the writer, and W. S. James, now Chief of Research for Studebaker Corpn. of America, was selected as the principal collaborator. The latter contributed much during his two years with the Associated Oil Co., to the development work that has followed. The writer extends to the Associated Oil Co. his appreciation for permission to disclose the details of distilling equipment. In petroleum refining the principal requisites of good economics are the separation of high-priced distillates from those of lower price; maxi-mum yield of any desired distillate; lowest capital investment in refining equipment; lowest cost of operation and maintenance, and the best adaptability and flexibility of the same refinery equipment for handling crudes of widely varying characteristics. The first two items mentioned, separation and yields of distillates are determined by efficiency of fractionating equipment,. Discussion in this paper is chiefly concerned with oil-heating equipment, combustion and furl economy. It has long been well known that velocity plays a very important part in all heat transfer systems. Any betterment in specific transfer. rates in such systems must. always involve velocity. Realizing this fact, IV decided to adopt as a basic principle, the employment of energy to impart velocity required for high transfer rates through a heating diaphragm, and our method of modernizing obsolete shell stills is founded on this principle. Mechanical energy is usually cheap and its rational rspcntliture is returned in the form of greatly increased heat transfer rates, on both oil and gas sides of the sheet. Certainly there is nothing new in this principle, the only novelty being that of our peculiar method of application On the oil side (Fig. I) use is made of a centrifugal pump to jet the oil against the heated sheet thereby creating a high velocity sheet flow over the entire fired area. Such a pump is one of the most efficient machines, so far developed, for moving fluids. 'I'he oil, under pressure impinging

Jan 1, 1928

By A. A. Toprac

The recurring problem of joint failures in ofjshore structures, coupled with the catastrophic collapse of many of these structures during Hurricane Hilda (1964), hay forced reconsideration of techniques presently used to design sfuctural joints. This paper presents results of studies conducted for this reconsiderat?on. Only right-angled T-joint,s and cross-joints where a brace was welded directly to the undisturbed surface of another tube (the chord) were considered. Tests were performed on seven T-joint and 12 oross-joint specimens of two types which were designed to give a broad but practicd range to the geometrical parameters believed to be of significance to the problem. These paramefers were expressed in dimensionless form. Each specimen of the T-joints was instrumented wirh both electrical resistance strain gauges and deflection dials. After the elastic tests were concluded, each specimen was loaded to failure by applying an axial tensile load to the brace. The cross-joints were tested to failure without measuring elastic strains. Theoretical solutions for the stresses in a cylindrical shell due to a distributed radial load over portions of its surface were numerically evaluated. The experimental results are compared with calculated values obtained using Bijlaard's and Dundrova's theoretical analyses. INTRODUCTION During the last IS years a large number of structures were built for the offshore exploration of oil both in the Gulf of Mexico and dong the Pacific Coast.' In all these offshore platforms, the tubular shape was extensively used since this shape provides outstanding strength in proportion to its weight, compared to other shapes, when all directions (x, y, z) are considered. Past use of tubes was hampered because of connection details. But with the advent of welding, it became no more difficult to connect tubular shapes than to connect rolled shapes. However, some problems have been encountered in actual construction in making welded joints that are adequate and yet economical. In trying to connect tubular members, designers have used a varied number of methods; consequently, some of the joints seem to be very expensive in detail while others appear weak and underdesigned. An inspection of offshore platforms owned by different companies indicates the use of a large number of joint arrangements and configurations. Such a variety of joint types in current service indicates the wide divergence of opinion that exists on how such joints should be designed, stiffened and strengthened. Fig. 1 shows the various types of connections that have been used in practice. This paper reviews the present state of art on tubular joints of the T and cross type, and presents results of experimental and analytical work being conducted at The U. of Texas and elsewhere. It is believed that such information will be of great help to designers for the formulation of proper design procedures for joints. CONNECTION PROBLEM Recently, cracks have been observed in several welded connections in offshore structures. Fortunately, until about 1 1/2 years ago, these failures have been localized and have not resulted in the collapse of structures or loss of life. For example, one platform installed in Louisiana during 1955 in about 60 ft of water had been subjected to four tropical hurricanes. This platform successfully withstood these forces and was later removed because operations at this location had been completed. Many joint failures were observed during the removal.

By J. F. Wilson

An experimental investigation has been made of gas-driven slug displacements in a system of high gas saturation to evaluate the process for use in a California reservoir. Fluid compositions, temperature, pressure and core permeability duplicated reservoir conditions as closely as possible. The temperature was above the critical of the slug materials. The slug composition required for 100 per cent oil recovery in the linear flow systems was found to agree with that determined from equilibrium phase studies. A qualitative theory for the slug displacement of two-phase systems is proposed and found to be in general agreement with the observed flow behavior. The theory predicts that the length of the reservoir fluid-slug transition Zone will increase with increased initial gas saturation and decrease with increased oil swelling accompanying the composition change from reservoir oil to the critical composition. The precipitation of small amounts of an asphaltic phase during the formation of the transition zone had no adverse effects on the flow behavior of otherwise miscible systems. INTRODUCTION Despite the large number of recent publications relating to oil recovery by miscible displacement, little information is available concerning the behavior of crude oil-natural gas systems at conditions likely to be encountered in field application. The laboratory data reported here were obtained during an investigation of the possibility of using a gas-driven LPG slug in a partially depleted California reservoir. Seven gas-driven slug displacements employing slugs of different compositions and sizes were made in 26- to 27-ft long sandstone cores. The equilibrium phase behavior of the systems was also determined. The features of primary interest in this study are the following. 1. Data were obtained on the displacement of reservoir fluids at reservoir conditions. 2. A high gas saturation existed in the long cores at the start of the displacements. 3. The temperature of the studies was above the critical of the slug materials. 4. A comparison between the flow behavior and equilibrium phase behavior, as illustrated by a pseudo-ternary phase diagram, is afforded for a system of considerable complexity. THEORY Phase Behavior The use of the pseudo-ternary phase diagram to illustrate the phase behavior in miscible displacements has been discussed by Clark, Schultz and Shearin. Sie-vert, Dew and Conley and Arnold, Stone and Luffel' have presented both phase equilibrium and flow data for true ternary systems. For the true ternary, the application of the theory is straight-forward; for a reservoir system represented as a ternary, the theory undoubtedly gives a qualitatively correct picture. One purpose of this investigation was to see if the pseudo-ternary phase diagram could be used to predict with reasonable accuracy the conditions necessary for miscible displacements with actual reservoir systems. MiscIBLE Displacement of Two-Phase System A large number of papers "I3 have treated the miscible displacement of a single-phase fluid from both an experimental and a theoretical viewpoint. However, the normal field application of the process will be in a partially depleted reservoir. Often the state of the system will be such that the mobility of the gas phase is greater

By R. C. Padfield

Experience over a 3-year period in Bethlehem Steel Corporation's plants has demonstrated the reliability of open-hearth roofs of bonded sprung-arch constructzon with burned basic brick. The design principles lor constructing these roofs include a minimum hot-strength requirement for the basic brick, expansion allowances that extend the full roof thickness, structural members to control arch contour, and a specified minimum roof rise. The greater stability of bonded roofs is explained in terms of the basic stress patterns of ring constrution and bonded construction. PRIOR to the development of successful sprung-arch roofs of basic brick, the majority of open-hearth furnaces in the United States were operated with sprung-arch roofs built of silica brick. Although many silica roofs used on open-hearth furnaces were ring-arch construction, Bethlehem Steel Corp. used bonded-arch construction because of its greater stability. In ring construction, each ring of brick is separately keyed and comprises an independent arch with the straight joints between rings traverse to the longitudinal axis of the furnace. In bonded construction, the bricks are laid in rows starting from the skewbacks so that the straight joints run parallel to the longitudinal axis of the furnace. Each brick in a given row is laid so that it spans the joint between two bricks in the row beneath it. Thus, the transverse joints across the arch are broken and the arch rings are thereby interlocked or bonded. When basic roofs were first being developed, the basic brick that were available had low hot strength. Such brick could not be safely used in sprung-arch construction without some means of suspending them. With the development of higher firing techniques by brick manufacturers and the recently introduced direct bonded bricks with high hot strength, the use of burned basic brick in sprung-arch roofs became feasible. The availability of high hot strength basic brick coupled with the potentially lower cost and proven stability of bonded construction prompted Bethlehem's Research Department to study the possibility of using basic brick in bonded roofs. With the full cooperation of plant ceramic engineers and open-hearth superintendents, particularly in 3 years of fur-nace trials, we developed the design criteria for bonded roofs and the corresponding property requirements for the basic brick that are discussed in this paper. DESIGN PRINCIPLES OF SPRUNG-ARCH BRICK ROOFS Stresses in Fixed Arches. A sprung-arch open-hearth furnace roof is generally built on rigidly held skewbacks. The constraint of the fixed support at each end adds a bending moment to the horizontal and vertical reactions at the ends of the arch. Fig. 11 shows the positive direction of forces acting on an arch fixed at both ends. Fixed arches can be analyzed when the members are continuous and have elastic properties. However, brick are inelastic, and arches built with individual brick segments cannot carry tensile stresses. Therefore, for practical solution of brick arches, empirical formulas have been derived from elastic theory that place design restrictions on arch dimensions to avoid development of tensile stresses. McDowell2 cites three main conditions for stability in sprung brick arches: 1) the thrust line of the arch should be maintained in the middle third of the thickness to avoid tensile stresses and resulting open joints in inner and outer curves of the arch; 2) the angle between the line of thrust at any joint and a line perpendicular to the joint must not exceed the angle of repose between brick; and 3) the maximum pressure at any point must not exceed the strength of the arch materials at furnace operating temperatures. The first and third conditions are particularly important in designing sprung-arch basic roofs because of the comparatively low hot strength of basic brick. According to McDowell's equation, if the thrust line is maintained within the middle third of the arch thickness, the unit pressure is obtained as follows: where p = unit pressure in psi, F, = resultant thrust normal to skewback in pounds per foot, t = arch thickness in inches, and z = distance in inches of thrust line from arch axis. When the resultant thrust normal to the skewback acts along the arch axis, z equals zero and unit pressure is simply the thrust divided by the cross-sectional area. If the thrust line moves to the limits of the middle third of the arch thickness, beyond which tensile forces would develop, z then equals one-sixth of the arch thickness and the unit pressure is double that when the thrust line is acting

Jan 1, 1968

By E. P. Mathewson

THE experiments described in this paper were made at the Washoe Reduction Works, Anaconda, Mont., for the purpose of determining the relative speed of elimination of the iron, sulphur and arsenic during the process of bessemerizing copper-mattes. The samples were taken from a horizontal "barrel" converter, 8 ft. in diameter and 12 ft. 6 in. long, having an average charge of 9 tons of matte, and blown with a 16-1b. air-pressure. All samples were taken with the blast on, turning the converter from its normal blowing-position to nearly verti¬cal, so that a conical mold, with a long handle attached to a horizontal rod, could be introduced from a platform above the converter into the mouth of the converter and a sample taken. The difficulties of taking a sample with the blast on are appar¬ent, and the irregularities of the lines in Figs. 1, 2 and 3 can be readily accounted for by the amount of slag in the samples. On the whole, the plotting of the results gives comparatively uniform lines, considering the conditions. The samples were taken by the regular sampling-force of the works at 10-min. intervals, as shown in Tables I., II and III, which also give the chemical analysis of the samples so taken. The test shown in Table I. was made with a new converter; that of Table II with a converter that had made three charges and had been cleaned out; that of Table III with a converter that bad blown one charge to white metal, and had then been " washed " out and used for the test. In plotting these results, it was necessary to take, as a basis, the percentage of copper in the samples. This basis does not exactly represent the true condition, since the volume is constantly decreasing and a certain quantity of copper passes into the slag, but it is as near as can be obtained in practice. Take, for instance, in Table I., the sample No. 5, which shows : Cu, 59.9;

Jan 1, 1907

By AIME AIME

DATA in this report enable comparisons to be made within the bituminous coal industry and comparison as well with copper and steel in respect to capacity and overdevelopment. The conclusions reached from the data will tend to correct numerous current misconceptions. The data have been prepared by various members of the Coal and Coke Committee of the A.I.M.E., from the most authentic sources avail¬able, and cover the period 1913-1924 wherever possible. CAPACITY AND OVERDEVELOPMENT Table 1 shows statistics for the industry, mainly from the U. S. Geological Survey sources, but partly from the U. S. Coal Commission reports. The mine capacity with equipment and labor as of given date is calculated for each state by obtaining the total man days worked as reported by the operators, and dividing this figure into the total production, getting the production per man day; this figure times the number of men employed times 308 (a theoretical full working year) equals estimated full-time capacity. Two major objections are made to this method-one that the total number of men employed is used instead of the number actually working, and the other that the number of days used only deducts Sundays and five holidays. Covering the first, the same number of men is used in estimating capacity as is used in actual production, and this condition exists at all times. Regarding the second, the opinion is general among coal men that 280 days is as great a figure as should be used, as it is practically impossible to keep any mine working full time at the same daily rate as when it is working part time. The capacity, as estimated on this basis, is much more nearly the true capacity, although even with present railroad efficiency this amount of coal could not be moved.

Jan 1, 1926

By S. S. Deshmukh

An important element of evaluating a materials- handling system by simulation lies in being able to examine the details of the proposed operation in a fashion which closely approximates real behavior. The added factor of flexibility permits including or deleting those parts of the problem which can be shown to be important or trivial. Used carefully, simulation can match manpower and equipment far more efficiently than conventional calculations. The same is true of interacting equipment systems. This efficiency results from being able to simulate the real fluctuations in a system by using empirical probability distributions compiled from existing operations. Simulation eliminates guessing as to efficiency, absenteeism, bunching, and the broad host of delays that influence productivity and substitutes operating data in place of the usual factors. In this respect, simulation improves detail and confidence in the reliability of engineering estimates.

Jan 1, 1970

By WILFRED SYKES

IT is with particular pleasure that I welcome the members of the Open-hearth Conference of the I American Institute of Mining and Metallurgical Engineers to this meeting, as I feel this is one of the most useful activities of the Institute in the field of ferrous metallurgy. For the information of our other members I might say the Open-hearth Conference was organized by Mr. Reynders when he was president, and is made up of open-hearth superintendents and metallurgists. All the plants are invited to send representatives, and practically all do, with the exception of the U. S. Steel Corporation. It meets twice a year to discuss various problems in connection with the manufacture of steel, and its minutes are published for the benefit of those attending, the expense being defrayed by the participating companies. This conference, .1 believe, should be a model for activities in the other branches of the work covered by this Institute. It works, not by reading formal papers, which we all know is not a very satisfactory method to bring out the experience of others, but rather by a round-table method of discussion. The spirit of the meetings is such that each member feels perfectly free to state his experience, and he gets as much as he gives. A series of topics for, discussion is brought to the attention of the chairman and after one is exhausted the next point is taken up. In this way there is a real interchange of ideas and experiences which cannot fail l to be of the greatest benefit to those attending. That these meetings are beneficial is evidenced by the "continued growing attendance and lively discussions at these half-yearly meetings.

Jan 1, 1930

By David J. Mack, A. H. Kasberg

The transformation characteristics are found to resemble a similar binary alloy. The differences are due to the alpha iron particles. While strength properties of the isothermally transformed alloys are high, ductility is low, resulting in high notch sensitivity. The elastic modulus can be varied widely and correlates with strength. Abnormal grain growth sometimes occurs. A CONSIDERABLE amount of work has been done on the isothermal transformation of high purity aluminum bronzes using the methods pioneered by Davenport and Bain.' The first isothermal study of these alloys was made by Smith and Lind-lief,' but more recently Mack", " and Klier and Grymko5 have continued the work. In commercial aluminum bronzes, one or more elements are always added to refine the ß grain size and to improve the mechanical properties. The effect of these elements on the isothermal transformation has not been reported in the literature. No systematic study of the properties of isother-mally transformed aluminum bronzes has apparently been reported, although adequate information is available on their properties after more conventional heat treatments. The fact that a eutectoid alloy will reject face-centered cubic a during isothermal transformation at appropriate temperatures2'" warrants investigation of the properties of such structures. Another cogent reason for determination of properties is the fact that the modulus of elasticity of the eutectoid alloy varies widely with the nature of the heat treatment." Preliminary experiments7 indicated that a high purity eutectoid alloy would not give reproducible results in property determinations because of ex- cessive ß grain growth during heat treatment, a single ß grain frequently occupying the entire cross-section of a standard test bar. For this reason a commercial aluminum bronze containing iron as a grain growth inhibitor was used. The isothermal transformation diagram of the alloy was first determined. On this basis, the heat treatments necessary to produce representative structures were selected and the properties determined. Material A commercial alloy (Ampco Grade 20) of the following composition was used: Cu, 83.68 pct; Al, 12.31 pct; Fe, 3.68 pct; Ni, 0.28 pct; and Mn, 0.03 pct. This alloy proved to be very close to the eutectoid composition and may be compared with the accepted value of 11.8 pct A1 in the binary Cu-A1 system. Comparison is valid only because of the "negative replacement effect" of the iron? Since traces of excess y² are present, the alloy is slightly hyper-eutectoid. The material was received in the form of 3/4 in. round, hot extruded bars. Specimens of approximately ? in. thickness were cut from this stock and drilled to allow suspension in the salt bath. The structure of the as-received material varied from 5 to 40 pct a + y2* in a matrix of ß. The amount of a + y² present was dependent upon the ß grain size of the extruded material. The coarse grained portions did not form as much a + Y, as did

Jan 1, 1952

By Donald H. McLaughlin, John H. Moses

IN the latitude of Lima, the broad uplifted block that forms the Andes is made up of a complex sequence of folded and faulted sediments and volcanics, broken by large and small bodies of granitic rocks and porphyries with which the principal mineral deposits are closely associated in both time and space. The intrusives are a final episode in the geologic history as revealed by the consolidated rocks, for after their emplacement and after the formation of the primary ore deposits in and about them the record is simply one of long continued erosion and uplift.

Jan 1, 1945

By E. V. Potter

For a nurnber of years, it has been known that manganese made by electro-deposition under certain conditions is ductile while under other conditions it is very brittle. The ductile metal is gamma manganese normally stable only between 1100 and 1138°C1; the brittle metal is alpha manganese, stable up to 727OC. The ductile metal is not stable, but gradually changes to the brittle form; the time required to complete the transfornlation is about 20 days at room temperature. Other observations have indicated that the transformation is completed in 10 to 15 min. at about 125°C, while at — 10°C, no appreciable change occurs in 9 months. The properties of gainma and alpha Illanganese in the pure state are ordinarilj difficult to determine because the gamma structure cannot be retained by normal quenching procedures and alpha manganese is so brittle, it is difficult to obtain specimens free from flaws. In a recent investigation2 some properties of gamma and alpha manganese were determined by studying the ductile electrolytic metal and determining the changes in its properties as it transformed to the brittle alpha form. These investigations provided an excellent opportunity for following the progress of the transition and studying its mechanism. The results of a series of such investigations are reported in this paper. Procedure Various properties of manganese were determined starting with the metal in the original ductile gamma form and following the subsequent changes in its properties as the metal transformed to the brittle alpha form. These observations were made at various temperatures, the data providing information regartling the mechanism of the transformation as well as the effect of temperature 011 the transition rate. Structure and resistivity values gave the most significant results, so this paper is concerned primarily with them. The structure was studied microscopically as well as by X ray diffraction. The resistivity was determined on strips of the metal by measuring the potential drop across a given length of the specimen. Current was passed through the specimen by wires soldered to its ends, and the potential connections were made by wires looped around the specimen near its center. The current was determined by the potential drop across a standard resistor connected in series with the specimen, the potential drop being measured on a potentiometer. In the temperature range from room temperature to 100°C an ordinary drying oven was used to heat the specimen. This was entirely satisfactory except at 100°C, where the time required to heat the specimen was long compared to the transition time, making the initial section of the resistivity curve unsatisfactory. To overcome this limitation, at 100°C and higher a thermostatically controlled oil bath was used to heat the specimens. The block on which the specimen was mountetl was plunged into the hot oil at the start of each test. The heating time was thereby reduced from 5 min. to about 6 sec, and dependable resistivity values could be obtained through 160°C. At this point the whole transition, including the warm-up time for the specimen, required only about 20 sec and it was not considered worth while trying to extend the temperature range further. Aside from the heating problem, the problem of making a sufficient number of accurate resistivity determinations became more and more difficult as the temperature was raised. Using the manually operated potentiometer, 100°C was about as far as it was possible to go. At this temperature and above, a self-balancing photoelectric recording potentiometer was used. Its response was quite rapid, and it proved to be entirely satisfactory all the way through 160°C, where the tests were stopped because of the specimen heating problem rather than any limitation of the potentiometer recorder. The metal used in these tests was prepared at the Salt Lake City laboratory of the Bureau of Mines. The method of preparation is discussed in a paper by Schlain and Prater.3 The sheets were about 2 3/8 by 5 3/16 in. and varied from 10 to 16 mils in thickness. They could be cut readily into pieces suitable for the various tests. X ray and microstructure determinations were made on pieces about 1/8 to 1/4 in. wide and about 1 in. long, while resistivity measurements were made on strips as long as possible and about 55 in. wide. The thickness of each sheet was not uniform over all its surface. This had no bearing on the X ray and microstructure determinations, but sections as nearly uniform and free from flaws as possible were chosen for the resistivity determinations. The gamma manganese was electro-deposited at 30°C, the time of deposition ranging from 5 to 12 hr for each sheet. Whenever possible, the tests were started directly after the metal was stripped from the cathode; otherwise the sheet was placed immediately

Jan 1, 1950

By S. R. Zimmerley, S. F. Ravitz

High-grade cobalt concentrates were produced from the complex Blackbird ore with very good recovery in continuous pilot-plant operations in which a low-grade bulk cobaltite-pyrite flotation concentrate was roasted in a multiple-hearth furnace to oxidize the pyrite selectively. The cobaltite was floated from the resulting calcine.

Jan 1, 1950

By R. M. Goldhoff, H. J. Beattie

The high-temperature properties of a 1 Cr-Mo-V forging steel are described. A series of controlled heat treatments was designed to delineate the effects of austenitizing and tempering treatments, temile strength, and grain size on such properties. Studies indicate that the mechanical properties and their varlations under creep can be described by the initial metallurgical structures and their changes droPirzg exposure, particulavly the carbide reactions. Such structures are described and correlated with the mechanical properties. FOR many years the large steam turbine industry has relied on the 1 Cr-Mo-V type forging steel for critical applications. Because of its adequate heat resistance and relative economy, it is currently in use in the temperature range up to about 1050" to 1075°F. Attempts to understand the large property variations attainable in this steel involve the structural modifications due to the wide latitude in its heat treatment. The heat treatment essentially involves a two-step process which includes solution-ing of carbides in the austenite range followed by a suitable tempering treatment below the critical to adjust the level of properties. The latter step is referred to as "secondary hardening" and is basically an ordinary aging reaction involving carbides. In the commercial heat treatment of large components of such steel, homogenizing and stress-relief anneals may be included and have some importance in determining subsequent properties. Several studies of the engineering properties of this steel as a function of transformation micro-structure have been reported.1 3 However, in this steel the carbide reactions, which are a function of composition and heat treatment, appear to be the property-controlling factor rather than the micro-structure defined as a transformation product. Thus, the tempering resistance of this type of alloy steel is mainly a function of the size and distribution of alloy carbides.4 However, it is also necessary to consider the stability of the microstructure and the effect of dynamic carbide reactions on subsequent properties. It is the purpose of this paper to show the interdependence of properties and corresponding structures, particularly carbide reactions, developed for a limited set of controlled heat-treatment conditions applied to 1 Cr-Mo-V steel. MATERIALS AND PROCEDURE The material for this work came from a large production forging whose chemical composition is shown in Table I. The property data accumulated on this steel as a function of heat treatment were room-temperature tensile and smooth- and notch-bar creep rupture at 1050°F (notch geometry: shank diameter = 0.357 in., depth = 50 pct, radius = 0.005 in.). To achieve controlled structural variations the temperature and time of both austenitizing and tempering were varied in a manner to produce a series of eight steels each at one of two grain sizes and one of two hardness levels in proper combination for valid comparisons. This will be clear upon examination of Table I. Structural studies involved the use of optical and electron microscopy as well as X-ray and selected-area electron diffraction. To reveal the nature of carbide precipitations, electrolytic extraction techniques were used with subsequent analysis of the residue by X-ray diffraction. Weight losses of the steel specimens during electrolysis were measured and successive chemical fractionations of the residues were applied and checked by X-ray examination. The details of fine structural distributions, morphologies, and crystallography of the precipitates as well as dislocation distributions were investigated by examining in the electron microscope three common types of preparation. a) Relief Replicas. Mechanically polished sections were etched in 2 pct nital, replicated with a nitrocellulose film, which was shadowed by chromium vapor deposited at a glancing angle of 20 deg. b) Extraction Replicas. A thin film of carbon was vapor-deposited on the polished and etched surface. The carbon films were then etched off and gathered on electron-microscope supporting grids. The carbides left imbedded in the carbon replica in their original distribution were then examined crystallo-graphically by selected-area electron diffraction. c) Thin Films. Specimens were mechanically ground and polished down to a thickness of 0.001 to 0.003 in. Final thinning was done electrolytically in a "chrome-acetic" electrolyte. When holes began to appear in the foil, the voltage was interrupted and applied in several 1-sec bursts. Sections of the foil between holes were thin enough to pass a 100-kv electron beam that carries an image.

Jan 1, 1965

By E. G. Williams

Manganese-ore has been found upon the Isthmus of Panama throughout' a region of nearly three hundred square miles, over the greater part of which, however, it is known only in small bodies without commercial value. Only six mines, controlled by two companies, have actually shipped ore, although a large area has been taken up in miningelaims. The ore-bearing region extends along the coast of the Carib. bean Sea, beginning on the west near Puerto Bello and extending easterly about 35 miles toward Point San Blas. Ore has been discovered in the interior, at a maximum distance of about 10 m. from the coast. Fig. 1 is a map of a portion of the Isthmus

Jan 1, 1903

By H. N. Hall

Reservoir and producing characteristics can govern the decision to use either a one-, two- or three-dimensional model for making predictions for gravity-drainage reservoirs. Examples of conditions requiring one-, two- and three-dimensional calculations are given. In 1961 the author presented a method for predicting one-dimensional gravity-drainage performance. This work has been exrendcd to obtain a three-dimensional model, which is described and for which a sample problem is presented. Introduction Many papers on gravity drainage or gas-cap drive'-3 have been presented for conditions where the reservoir is treated as a single areal segment so that, in effect, only one-dimen-sional flow is considered. Other authors'-Q ave given evidence showing that the one-dimensional concept would be unsatisfactory to predict reservoir performance for certain types of reservoirs. Experience has indicated that specific reservoir and producing conditions govern whether one-, two- or three-dimensional concepts must be used as a basis for reliable reservoir performance predictioils. Previously the author presented a paper outlining a method for predicting the performance of gravity-drainage reservoirs.' That paper treated the reservoir as a single areal segment so that it was applicable for only one-dimensional flow. The work has been extended to obtain a three-dimensional model that can be used to predict performance of gravity-drainage reservoirs. Although capable of being three-dimensional, it can be used equally well for one- and two-dimensional predictions. This paper discusses those reservoir and producing conditions governing the choice of model, and also describes a three-dimensional model suitable for predicting reservoir performance in the more complex situations. Discussion The Choice of Model To predict reservoir performance, it is necessary to represent the reservoir by a physical model. A mathematical model, based on the assumed physical model, then is used to predict the movement of oil and gas within the reservoir. The word "model" is used here to connote the combination of both a physical model and a mathematical model based on the physical model. Certain types of reservoir situations may be predicted suitably with a one-dimensional model, whereas two- and three-dimensional models may be required for other situations. This section illustrates reservoir conditions associated with the use of a specific type of model. Many types of reservoir structures are such that gravity drainage possibly could be an important factor in oil production. Production practices, as well as the nature of the structure. can influence the type of model that should be used. obviously, it is impossible to discuss all combinations of reservoir structure and production practices that might be encountered in gravity-drainage reservoirs. The following are typical examples of conditions where a choice must be made among a one-, two- or three-dimensional model to predict reservoir performance satisfactorily. Conditions Requiring a One-Dimensional Model Fig. la shows contours for an asymmetrical anticline in which gravity drainage might be expected to be important. Fig. Ib depicts a cross-section along Line A-A in Fig. la. Existence of a gas cap is a good clue that gravity drainage will be an important factor in producing oil from this type of reservoir. However, it is not essential since a gas cap will form as oil is produced from the reservoir. If the proper combination of reservoir permeability and withdrawal rates is present, the reservoir will behave like a

Jan 1, 1969

The Alligator Ridge Project is owned jointly by Amselco Minerals Inc. and Occidental Minerals, with Amselco being the operator. It is the latest of Nevada' s gold heap leaching operations , having gone into operation in October of 1980 after a design and construction period of only seven and one-half months. Alligator Ridge is located about 77 km (48 miles) northwest of Ely, Nevada. Three separate but adjacent ore bodies will be mined: Vantage I, II and III. The first lies virtually at the surface and is totally oxidized; the second is somewhat deeper and contains some carbonaceous material; and the third is at the lowest horizon and contains substantial carbonaceous ore. The ore is a Carlin- type siltstone which has been silicified, especially at depth, and contains finely disseminated free gold. Exploration drilling on Alligator Ridge resulted in the defining of an ore reserve of about 4.54 million mt (5 million st) averaging 4. 12 g Au per mt (0. 12 oz Au per st). A pilot heap leaching program was run during 1979. Because of the high content of fine material in portions of the ore body, one test heap of 5,000 tons was leached, after being crushed to 19 mm (314 in.), in the conventional manner using cyanide and caustic while a second heap of 2,500 tons of ore was agglomerated with cement before leaching. Results of this work were reported at the 1980 American Mining Congress meeting by Paul Chamberlin (see Bibliography). The test work clearly indicated the superior leaching qualities of the agglomerated ore, and the plant was designed on this basis. Run-of-mine ore is crushed in an open-air crushing plant using a jaw crusher followed by two cone crushers, one standard and one shorthead. Provision was made to bypass the shorthead when the ore is wet from rain or snow. Crushed ore at 19 mm (314 in.) size is mixed with cyanide solution and cement, with the ratio of the latter to the ore being 2 to 5 kg per mt (4 to 10 lb per st). The resulting moisture content is about 870, and the fines are effectively bound to the coarse particles so that migration of the fines in the heap does not take place during leaching. For agglomeration, Amselco uses a rotating drum 2. 75 m 0 by 6 m long (9 ft 6 by 20 ft). For the same agglomeration, Candelaria uses three "grasshopper" conveyors, with introduction of caustic- cyanide solution at the conveyor transfer points. Provision was made for future addition of cement slurry at these same points.

Jan 1, 1981

By E. S. Wheeler, M. W. Murphy

A LARGE part of the molybdenum produced in Colorado is converted and consumed in the Eastern States. As the raw materials and the power needed for the conversion of the Colorado concentrate are also accessible in the Eastern States, the conversion plant has been installed some 1500 miles east of where the ore is mined and milled. When concentrate was first produced at Climax in 1918, a custom smelter converted the product into ferromolybdenum. By 1924, the Company had decided to produce calcium molybdate and rented a building and installed equipment for that purpose at Langeloth, near Burgettstown, Pa., about thirty miles west of Pittsburgh. For the first few years the plant was a simple one of small capacity. A small hand-rabbled roaster was used, the product of which was made iota calcium molybdate by a conventional method; then an eight hearth mechanically rabbled roaster was installed to increase and speed up production. The output was considerably less than a million pounds of contained molybdenum annually until 1928, when a small part of the produc-

Jan 1, 1946

By V. S. Gupt, W. H. Somerton

Rock may undergo great changes in physical properties when heated to high temperatures and then cooled, The temperature and intensity of reactions causing rock alterntiorl.s can he controlled by introducing certain chemicals during heat treament. Three typical outcrop sandsone samples were saturuted with common salt solutions, then heated to several maximum temperatures. After cooling, it was found that per-rrreuhilities had increased much more for salt-saturated samples than for samples not saturated with salt but heated to the same temperatures. This was only true, however. for samples heated above the melting points of the particrrlar salts. Potassium chloritle was particularly effective with Bandera sandstone. Samples saturated with potassium chlorirlr. solution and heated to 900C showed an 11-fold increa.se in perrrieahility. Samples without potasrirdrn chloritle but heated to the .same temperature. showed only a 2.7-jold incresre in permecahility. In application, it seems possible that injecting chemicalc into the formations from a wellbore followed by applying intensive borehole heating might promote reactions which would greatly improve permeability of the formalions. INTRODUCTION Great changes in the physical properties of rocks which have been heated to temperatures in the range of 600 to 800C have been reported earlier. Permeability increases of 50 per cent, and equivalent decreases in sonic velocity and breaking strength have been observed. Although there might be some suppression of certain reactions responsiblc for these changes when rock samples are heated under simulated reservoir pressure conditions. recent work has shown that these are more than offset by the increased importance of other reactions at high pressures. The reactions considered responsible for alteration of rock properties by heating include differential thermal expansion. dehydration, phase changes and dissociation of mineral constituents. Ceramists have long known that temperatures at which reactions occur can be raised or lowered by the presence of certain impurities in the sys. tcnl. Thus the possibility exists that by saturating rocks with appropriate solutions. desired reactions might be accelerated and unwanted reactions might be suppressec! when the rock is heated. Purpose of the present work was to investigate the effects of several common salts on the thermal alteration of sandstones. Types of reactions which might occur are reviewed and the findings of a number of thernlochemical alteration tests are presented. THEKMOCHEMICAL ALTERATION OF SANDSTONE MINERALS The most abundant constituent of most sandstones is quartz. Quartz can exist in at least eight different forms, but in the temperature range of immediate interest (to 900C) only two forms are of importance—alpha quartz below 573C and beta quartz above this temperature. Although the alpha-beta inversion of quartz is very important in thermal alteration of rocks. it is not particularly important here because the inversion temperature cannot be changed significantly by the presence of impurities or by the application of pressure. The transition temperature of quartz to tridynlite is 867C. but the transition is very sluggish. Tridymite is considered to be a metastable transition phase between two stable phases: quartz?cristobalite. However. the transition temperature for tridymite to cristobalite is 1,470C.4 The quartz-tridymite-cristobalite transition can be accelerated substantially by the presence of fluxing agents. Finely divided calcium, magnesium and titanium oxides accelerate the conversion while A12O may retard it. A Mixture of NaCl and CsCl reduces the temperature for cristobalite formation by as much as 420°C. Feldspars constitute the second most important mineral in sandstones. The melting points of feldspars range between 1,000 and 1,700°C depending upon the variety. No information available indicated any important role of fluxing agents in the thermal alteration of this group of minerals. Carbonate minerals are subject to dissociation at temperatures within the range of the present investigation. The dissociation of magnesite can start at a temperature of 373°C, but the reaction is sluggish and might not occur untll a temperature of 500°C or ,higher is reached. Dolomite dissociates in two stages at 500°C and 890°C, whereas calcite dissociation temperature is about 885C. Because CO2 is released in the dissociation of carbonates, ail such reactions are somewhat dependent upon CO2 partial pressure. In the absence of CO: in the surrounding atmosphere, the dissociation of calcite starts at 500°C.However. when 1 atm of CO surrounds the sample, the dissociation does not start until 900C. The other carbonates are apparently much less sensitive to a change in partial pressure of CO2. The aragonite calcite transformation can occur an!. where within the temperature range of 357 to 488°C. depending upon the presence of impurities such as barium. strontium. lead and perhaps zinc. The differential thermal analysis (DTA) curves of both magnesitc and dolomite vary with the presence of 'impuritics. The presence of iron in particular seems to affect the magnesitc DTA curve

Jan 1, 1966