Search Documents

By H. W. Schadler

The superplastic behavior of low carbon and manganese bearing steels has been evaluated. The results of elevated-temperature stress-strain rate and elongation tests are reported which indicate that high strain rate sensitivity (>0.5) and adequate elongations are achievable in ultrafine-grained steels 1 to 2 p, but at strain rates which are not commercially attractive. It has been demonstrated that the fine grain size is retained after long times and high strains if the temperature is kept within the range of the two-phase (a + ?) field. INTEREST in superplasticity has been stimulated by the desire to: 1) understand the origin of, and mechanisms responsible for, the large uniform elongations observed, and 2) exploit this property for commercial advantage in metal forming operations. Although the Zn-22 wt pct Al alloy presently being studied as a model material1-5 may find application in sheet forming and extrusion, the potential of super-plasticity should best be realized in large tonnage materials, such as steel and aluminum alloys. The degree of superplasticity in low-carbon and manganese-bearing steels has been evaluated. The results of elevated-temperature stress-strain rate and elongation tests on ultrafine grain size material are reported. Avery and Backofen6 and Hart7 have shown that geometrically stable flow leading to extensive uniform elongation in the tension test is associated with high values of the strain rate sensitivity, m, defined: Lozinsky had reported that titanium and zirconium experience permanent deformation if subjected to a constant load and cyclic heating through the temperature range of the phase transformation. Although strain rate sensitivities in excess of about 0.2 had not been reported previously for steel, permanent deformation had been observed11-13 in a wide variety of steels subjected to a constant load and cyclic heating through the temperature range of the a-? phase transformation. Thus by analogy, steel could be expected to exhibit high strain rate sensitivity but only in the a + ? condition. High strain rate sensitivity has been observed at 650°C (a + Fe3C), but not reported as such, by Bailey, Dickenson, and pearson14 in 1931 at a strain rate of about 10-9 per min. It then remained to determine whether high tensile elongations would be observed in a rate-controlled test at constant temperature and at what strain rate strain rate sensitivity values greater than 0.5 would be observed. Since previous experience8 had indicated the importance of fine grain size to realizing high m at reasonable strain rates, it was first necessary to produce an ultrafine grain size and then keep the grains from growing during the test. The results of this investigation show that fine grain size can be readily produced16 and maintained by restricting the temperature of testing to below the ? transus. Further, superplasticity (high m and large uniform elongation) is observed. However, the strain rate range is only marginally useful for commercial forming operations with the finest grain size produced. MATERIAL The material investigated initially was a 1.9 wt pct Mn, 0.42 wt pct C, hot-rolled bar previously used by Low and Turka1015 and available in the laboratory. The 0.500-in. round was cold-rolled to a 0.090-in. flat, annealed for 4 hr at 850°C in argon, air-cooled, and cold-finished to 0.050 in. Subsequently, four additional steels of the compositions given in Table I were investigated to explore the effects of manganese, carbon, and test temperature on the observed stress-strain rate behavior. These steels were melted under argon, cast to 0.75 by 2 by 5 in. slabs, hot-rolled at 850°C, surface-finished to 0.13 in., and cold-finished to 0.050 in. Sheet tensile specimens 0.200 in. x thickness with 1- or 2-in. gage length were cut parallel to the rolling direction. Table I also includes the nominal transformation temperatures for the AISI 1340 and the four experimental steels. EXPERIMENTAL PROCEDURE Production of Fine Grain Size. Ultrafine grain size (1 to 5 p) was considered essential for this studv. Grange16 has described two techniques for producing

Jan 1, 1969

By Jesse Betterton

IN the Parkes process of lead refining, after desilverization has been completed by means of zinc additions, there will remain in the lead from 0.5 to 0.6 per cent zinc. At this stage in the refining practically all impurities are reduced to refined lead specifications except zinc and antimony. All excess of copper and nearly all the arsenic goes out with the silver. Silver remaining should not exceed 0.1 oz. per ton. It thus remains only to remove zinc and antimony to produce refined lead. The older practice was to complete refining by means of oxidation processes in reverberatory furnaces. Essentially this consisted of heating the lead to 1200° to 1300° F. and allowing it to come in contact with a considerable excess of air passing through the furnace, or accom-plish the same result by blowing the lead with steam by means of pipes introduced for that purpose, at the same time allowing air to enter the furnace. Usually some procedure involving alternate oxidation and reduction with fine coal or coke was employed in order to reduce the weight of dross or skim finally removed from the furnace. This practice had many elements of weakness in that the main flow of lead, after the preceding expensive operations had been performed, and the whole refining process nearly completed, was subjected to an operation at a comparatively high temperature, which involved much lead loss if the furnaces were not on bags, and the production of 3 to 5 per cent of the weight of the lead as dross or skim, which had to be resmelted and the lead either refined or produced as antimonial lead. In addition, the operating expense of the process was a considerable item. The, process of dezincing with chlorine was developed as a substitute for the foregoing described oxidation process, and finally resulted in such advantages as nearly equal operating costs, a practical elimination of the lead loss, and the direct production of a very valuable byproduct, zinc chloride, that may be sold as such or retreated for its zinc and chlorine contents, both of which can be reused in the refining processes.

Jan 1, 1933

By AIME AIME

THE following paragraphs comprise such information as the Secretary has been able to obtain concerning the members and associates whose deaths have been reported. Further particulars or corrections of errors, and biographical data concerning deceased members or associates not already noticed in this way, are solicited. [SECRETARY'S NOTE.-All of these notices have been revised, and some of then have been more or less completely prepared, by me. To those which contain more particularly the expression of my personal feeling, my initials have been appended. The labor of preparing or editing these paragraphs has been in many respects both welcome and interesting, on the one hand, and sorrowful, on the other. In going through the list, I have repeatedly felt like one who, visiting the Morgue, suddenly comes upon the pale face of a dear friend, of whose death lie was not aware ; and, even when this fact was known to me, the work of recording it has brought upon me a flood of recollections, almost preventing the discharge of that official duty. The list for 1907 seems to me to he peculiarly sad, comprising, as it does, so many sudden deaths by violence or accident, so many veterans, removed too soon, and so many young men whose early departure impoverishes the future, even more than the present. Probably, this feeling on my part is largely due to the circumstance that the increased membership of the Institute necessarily in¬volves an increase of the annual death-list. Probably, also, it is connected with the circumstance that during the first years of the history of the Institute-say from 1871 to 1880-it was joined by men of all ages, and that the death-rate is consequently now above the average which would result from the normal annual addition, principally of young men. And finally, I must admit that, as one of the original members of the Institute, and practically connected with it for nearly thirty-seven years as Acting President, President or Secretary, I am peculiarly impressed and depressed by the successive deaths of those who were my associates in the years of its early struggles and triumphs. I do not wish to inflict upon my younger colleagues the melancholy reflections of an increasingly lonesome old man. In fact, my prevailing mood concerning the Institute is not at all melancholy, but triumphant and hopeful. If I may be permitted to preach at all, I would enforce, from the texts given below, a moral which many of them declare so forcibly as to preclude the necessity of expository enforcements-namely, the duty of every one of us, old or young, to give to his brethren, as he goes along, and without waiting for some future occasion for a comprehensive and monumental contribution to technical literature, the results of his observation and experience. When I look at this list of names, my personal sorrow over many of them is drowned in my professional reflection as to each and all-How much has died with

Jan 1, 1908

By Matti J. Saarivirta

Two new precipitation hardening copper-base alloys, Cu-1.5pct Ti-2.5 pct Sn and Cu-1.5 pct Ti-2.5 pct Sn-0.4 pct Cr were developed. High strength and medium conductivity are obtained by solution annealing and subsequent heat treatment. Combination of solution annealing, cold working, and heat treatment increases the strength further. Good elevated temperature strength and ductility makes these alloys superior to copper-beryllium-cobalt alloys. A considerable amount of research work is being done throughout the world to develop new and improved copper-base alloys. In many cases, the object is to develop alloys having a combination of high electrical and thermal conductivities, and high strength. The problem is complicated by the fact that any alloying element added to increase strength, invariably decreases conductivity. Among the few commercial precipitation hardening type copper-base alloys, the Cu-Be-Co alloys are best known. These alloys are used in many applications that require good spring characteristics cornbined with high strength and moderately high electrical conductivity. They can be formed readily after solution annealing, then heat treated to obtain high strength and conductivity. Because of the relatively high cost of the Cu-Be-Co alloys, considerable research has been aimed at developing new lower cost alloys having similar properties. As far as is known today, the binary Cu-Ti alloy is the only one whose properties are

Jan 1, 1962

By V. H. Wilhelm

Drilling activity in California during 1939 decreased approximately 15 per cent from that of the previous year. New reserve discoveries were the lowest in many years, but extensions, development of deeper sands, and reappraisals, indicated enough new potential to more than equal 1939 withdrawals of about 223,644,000 barrels. On June 1 a new uniform method of allocation was adopted, which had the immediate effect of reducing production, so that approximately 6,000,000 bbl. of crude were withdrawn from storage during the year. Market demand averaged 628,845 bbl. per day as compared with a daily production of 612,945 barrels. The rate of drilling was slow during the first five months because of the unfavorable storage situation. Subsequent to the adoption of the new uniform method of allocation on June 1, drilling was speeded up and continued at a rapid rate throughout the remainder of the year. As a result of prospecting, four new fields were discovered and seven fields were measurably extended. All of the new discoveries were made in the San Joaquin Valley. Statistics of production and development arc given in Fig. 1 and Tables 1 to 3. New Discoveries Coalinga-Northeast.—The Amerada Petroleum Corporation discovered a second Eocene shore-line field north of the Coalinga Nose when it brought in well S.P.L. 7-17 in sec. 17-19-16, flowing 4230 bbl. of 32.4" gravity oil and 14,200,000 cu. ft. of gas at a depth of 8237 ft., from the "Gatchell" sand of Eocene age. This field, 2 miles north of the Coalinga Nose field, is considered to be a separate structure because it has a gas cap and a lower water table. The structure is a broad, gentle anticlinal nose probably separated from the southerly Coalinga Nose field by a shallow syncline. Production is sealed updip by the pinching out of oil sands. The average sand thickness is approximately 200 ft., the top 75 ft. containing mainly gas. The sand has an average permeability of 1000 millidarcys and an average porosity of 25 per cent. The productivc area of the field is estimated to be between 1200 and 1500 acres.

Jan 1, 1940

By V. H. Wilhelm

Drilling activity in California during 1939 decreased approximately 15 per cent from that of the previous year. New reserve discoveries were the lowest in many years, but extensions, development of deeper sands, and reappraisals, indicated enough new potential to more than equal 1939 withdrawals of about 223,644,000 barrels. On June 1 a new uniform method of allocation was adopted, which had the immediate effect of reducing production, so that approximately 6,000,000 bbl. of crude were withdrawn from storage during the year. Market demand averaged 628,845 bbl. per day as compared with a daily production of 612,945 barrels. The rate of drilling was slow during the first five months because of the unfavorable storage situation. Subsequent to the adoption of the new uniform method of allocation on June 1, drilling was speeded up and continued at a rapid rate throughout the remainder of the year. As a result of prospecting, four new fields were discovered and seven fields were measurably extended. All of the new discoveries were made in the San Joaquin Valley. Statistics of production and development arc given in Fig. 1 and Tables 1 to 3. New Discoveries Coalinga-Northeast.—The Amerada Petroleum Corporation discovered a second Eocene shore-line field north of the Coalinga Nose when it brought in well S.P.L. 7-17 in sec. 17-19-16, flowing 4230 bbl. of 32.4" gravity oil and 14,200,000 cu. ft. of gas at a depth of 8237 ft., from the "Gatchell" sand of Eocene age. This field, 2 miles north of the Coalinga Nose field, is considered to be a separate structure because it has a gas cap and a lower water table. The structure is a broad, gentle anticlinal nose probably separated from the southerly Coalinga Nose field by a shallow syncline. Production is sealed updip by the pinching out of oil sands. The average sand thickness is approximately 200 ft., the top 75 ft. containing mainly gas. The sand has an average permeability of 1000 millidarcys and an average porosity of 25 per cent. The productivc area of the field is estimated to be between 1200 and 1500 acres.

Jan 1, 1940

By C. BARING HORIVOOD

(Chattanooga Meeting, October, 1908.) THIS paper is intended, in the light of recent investigations, to call attention to some of the essential features of good practice in sampling and mine-valuation. Mine-sampling may be divided broadly into two classes : (1) development-sampling and computation of ore-reserves; and, (2) stope-sampling and estimation of stope-values. DEVELOPMENT-SAMPLING. It is with development-sampling only that this paper deals-the term development being taken to mean the opening-up of a mine by cross-cuts, drives, connections, etc., preparatory to actual extraction of the ore for milling. In development-sampling the work of the sampler and the consequent estimation of the probable value of the mine or portions of the mine, as the case may be, cannot be verified until a later period, when the ground thus sampled has been exploited; hence, extreme care and accuracy are essential. Moreover, the development-sampler has to foresee and allow for contingencies which may arise when stoping is started. It follows that the sampling, in development-work, demands familiarity with the conditions likely to be encountered later in actual mining. In stopes, on the other hand, sampling is clone under actual working-conditions, and the sampler's valuations are immediately checked by the gold-output, or in some cases by a second sampling of the broken ore. A stope-sampler therefore need not be an experienced miner, though he should possess sound technical training and work accurately. Should he be somewhat inexperienced, be soon has his errors discovered for him, and learns to avoid them. Taking these facts into account, it is obvious that a mining company employing two or more samplers should

Jan 1, 1909

On the Art of Metallography (Howe Memorial Lecture), by F. F. Lucas; Beneficiation of Iron Ore. Abstract of paper by C. E. Williams followed by Round Table Discussion; A Statistical Analysis of Blast-furnace Data, by R. 8. McCaffery and R. G. Stephenson; Air Discharge of Circular Tuyeres, by R. S. McCaffery and D. E. Krause; Open-hearth Steel Process as a Problem in Chemical Kinetics. by E. R. Jette; Carbon-oxygen Equilibrium in Liquid Iron, by H. C. Vacher and E. H. Hamilton; A Thermodynamic Study of the Phasial Equilibria in the Bystem Iron-carbon (Abstract), by Yap, Chu-Phay; Influence of Dissolved Carbide on the Equilibria of the System Iron-carbon (Abstract), by Yap, Chu-Phay; Inclusions and Their Effect on Impact Strength of Steel, I and 11, by A. B. Kinzel and W. Crafts: Method for Electrolytic Extraction of MnO, MnS, FeS and Si02, Inclusions from Plain Carbon Steels, by G. R. Fitterer; Permanent Growth of Gray Cast Iron, by W. E. Remmers; Some Notes on Blue Brittleness, by L. R. van Wert; Austenite-pearlite Transformation and the Transition Constituents, by A. Sauveur; Age-hardening of Austenite, by F. R. Hensel; Transformational Characteristics of Iron-manganese Alloys, by H. Scott; Composition Limits of the Alpha-gamma Loop in the Iron-tungsten System, by W. P. Sykes; Magnetic Properties Versus AUotropic Transformations of Iron Alloys, by T. D. Yensen and N. A. Ziegler; Dilatometric Study of Chrome-nickel-iron Alloys, by V. N. Krivobok and M. Gensamer; Low-carbon Steel, by H. B. Pulsifer; Bright Annealing of Steels in Hydrogen, by F. C. KeUey; Development of Continuous Gas Carburieing, by R. J. Cowan. Transactions, Institute of Metals Division, 1931. 500 pages. Index. Papers and discussions presented before the Division at Chicago, Sept. 22-26, 1930 and New York, Feb. 16-19, 1931. X-ray MetallograpIhy: X-ray Determination of Alloy Equilibrium Diagrams (Annual Lecture), by A. F. Westgren; Suppressed Constitutional Changes in Alloys. by G. Sachs; Texture of Metals after Cold Deformation; by F. Wever. Theoretical Metallurgy: Studies upon the Widmanatitten Structure. I.—Introduction. The Aluminum-eilver System and the Copper-silicon System; by R. F. Mehl and C. S. Barrett; Studies upon the Widmanstatten Structure, 11.—The Beta Copper-einc Alloys and the Beta Copper-alumnum Alloys, by R. F. Mehl and 0. T. Mareke; Application of X-rays in the Manufacture of Telephone Apparatus, by M. Baeyerts; Thermal Conductivity of Copper Alloys. 11.—Copper-tin Alloys; 111.—Copper-phosphorus Alloys, by Cyril Stanley Smith; Thermodynamic Study of the Equilibria of the Systems Antimony-bismuth and Antimony-lead, by Yap, Chu-Phay. Ganeral: Cemented Tungsten Carbide; a Study of the Action of the Cementing Material, by L. L. Wyman and F. C. Kelley; Influence of Casting Practice on Physical Properties of Die Castings, by C. Pack; Fabrication of the Platinum Metals, by C. S. Sivil; Effect of Certain Alloying Elements on Structure and Hardness of Aluminum Bronze, by 9. F. Hermann and F. T. Sisco. The WorkinG oF Metals: Metal Working in Power Presses, by E. V. Crane; Forming Properties of Thin Sheets of Some Nonferrous Metals, by W. A. Straw, M. D. Helfrick and C. R. Fischrupp; Die Pressing of Braas and Copper Alloys, by J. R. Freeman. Jr.; Plasticity of Copper-sina Alloys at Elevated Temperatures. by A. Morris: Directional Properties in Cold-rolled and Annealed Copper, by A. Phillips and E. 9. Bunn; Effect of Combinations of Strain and Heat Treatment on Properties of Some Age-hardening Copper Alloys by W. C. Ellis and E. E. Schumacher; Constituents of Aluminum-iron-silicon Alloys, by W, L. Fink and K. R. Van Horn; Equilibrium Relations in Aluminum-antimony Alloys of High Purity, by E. H. Dix, Jr., F. KeUer and L. A. Willey; Equilibrium Relations in Aluminum-magnesium Silicide Alloys of High Purity, by E. H. Dix. Jr., F. Keller and R. W. Graham; Constitution of High-purity Aluminum-titanium Alloys, by W. L. Fink, K. R. Van Horn and P. M. Budge; Experiments on Retarding the Age-hardening of Duralumin, by E. H. Dix. Jr. and F. KeUer; Aluminum-silicon-magnesium Casting Alloys, by R. S. Archer and L. W. Kempf; Modulurr of Elasticity of Aluminum Alloys, by R. L. Templin and D. A. Paul; Quenching of Alclad Sheet in Oil, by H. C. Knerr.

Jan 1, 1931

By P. V. Martin

Shortly after the middle of the nineteenth century, the invention of the regenerative open-hearth furnace and the development of the Bessemer process stimulated a rate of steel production whose magnitude created an unprecedented demand for pig iron. Revolutionary improvements in furnace design, auxiliary equipment, and operating technique enabled the blast furnace to keep abreast of the constantly increasing requirements of the steel mill. The development of improved blowing equipment, more adequate facilities for material handling, and particularly the general use of anthracitc and coke to replace the physically weaker charcoal, led to a rapid expansion in both the height and volume of furnaces. Beyond a doubt, however, the greatest single factor in blast-furnace improvement at this time was the use of the higher blast temperatures made available by the replacement of the recuperative iron pipe stoves by the regenerative Cowper brick stove. The increased blast temperature not only resulted in greater output but also reduced fuel consumption . far more than could be explained by the additional heat content of the blast. The progress of iron manufacturing was thus largely mechanical and thermal. Little attention was given the chemistry of the process until the publication of the investigations of Sir Lowthian Bell.1 Bell's painstaking experiments and investigations gave to the blast-furnace man his first real scientific conception of blast-furnace chemistry. Bell's recognition of the dual function of the carbon, the technical importance of reversible reactions and chemical equilibria, and his conception of the degree of oxidation of the carbon as shown by the analysis of the outgoing gases as a criterion of furnace efficiency, laid the foundation upon which has since been erected the structure of blast-furnace theory. Prominent among those availing themselves of Bell's data as .a basis of further study was M. L. Gruner,2 professor of the French School of Mines. His "Blast Furnace Phenomena," published in 1870, presented

Jan 1, 1940

By P. V. Martin

Shortly after the middle of the nineteenth century, the invention of the regenerative open-hearth furnace and the development of the Bessemer process stimulated a rate of steel production whose magnitude created an unprecedented demand for pig iron. Revolutionary improvements in furnace design, auxiliary equipment, and operating technique enabled the blast furnace to keep abreast of the constantly increasing requirements of the steel mill. The development of improved blowing equipment, more adequate facilities for material handling, and particularly the general use of anthracitc and coke to replace the physically weaker charcoal, led to a rapid expansion in both the height and volume of furnaces. Beyond a doubt, however, the greatest single factor in blast-furnace improvement at this time was the use of the higher blast temperatures made available by the replacement of the recuperative iron pipe stoves by the regenerative Cowper brick stove. The increased blast temperature not only resulted in greater output but also reduced fuel consumption . far more than could be explained by the additional heat content of the blast. The progress of iron manufacturing was thus largely mechanical and thermal. Little attention was given the chemistry of the process until the publication of the investigations of Sir Lowthian Bell.1 Bell's painstaking experiments and investigations gave to the blast-furnace man his first real scientific conception of blast-furnace chemistry. Bell's recognition of the dual function of the carbon, the technical importance of reversible reactions and chemical equilibria, and his conception of the degree of oxidation of the carbon as shown by the analysis of the outgoing gases as a criterion of furnace efficiency, laid the foundation upon which has since been erected the structure of blast-furnace theory. Prominent among those availing themselves of Bell's data as .a basis of further study was M. L. Gruner,2 professor of the French School of Mines. His "Blast Furnace Phenomena," published in 1870, presented

Jan 1, 1940

By Edgar Stansfield

ONE of the most striking features of the coal series passing from peat through brown coal, lignite, etc., up to anthracite is the gradual reduction of moisture content with the increased coalification of the original plant material. Thus drained peat from a bog may contain 90 per cent water, brown coal contain 50 per cent, lignite 30 per cent, while a bituminous coal may contain only 1 per cent moisture. Moisture, therefore, is one of the important factors to be considered in coal classification, especially with the lower rank coals. With bituminous and higher rank coals the moisture content is less satisfactory for classification; it may even pass a minimum value and then increase with increasing rank to anthracite and superanthracite. Coal in an undisturbed seam contains moisture which is an integral part of the coal, but it may also be wet with free, underground water percolating through the seam. Only the former must be considered in evaluating the moisture content of the coal for classification purposes; this will be called the "true moisture" of the coal. When the seam is mined and sampled the sample taken may show the true moisture; on the contrary, it may contain in addition free mine water or, especially in dry, well ventilated mines, it may contain less than the true moisture. Coal contains unstable organic compounds which may decompose, with the production of moisture, when the coal is exposed to air at ordinary temperatures, or is heated with or without exposure to air. The potential moisture of a coal therefore is higher than its actual moisture. The lower the rank of the coal, the greater its instability, as a rule, and the greater the care necessary to avoid oxidation or decomposition in any investigation of moisture content. The majority of coal workers have preferred, on account of the difficulty in evaluating the true moisture of a coal, and for other reasons, to classify coals by analyses calculated to the dry-coal basis. A number of workers familiar with lower rank coals have recently insisted that the classification of such coals can be satisfactory only if analyses on the moist-coal basis are employed. The moisture-holding capacity of coal is therefore intimately connected with coal classification, and in this paper a procedure is outlined for determining the true moisture of a coal.

Jan 1, 1932

By A. D. Wilkinson

A CROSS-SECTION of the converter aisle through one of the converters and reverberatories is shown in Fig. 5. The aisle is 280 ft. long by 60, ft. wide by 681 ft. to the roof trusse, which have a 63-ft. span and are us )ported by steel columns spaced at 2b-ft. centers. Two 80-ton electric trails, supplied by the Welman Smith .Owen Engineering Co., with 20-ton auxiliary lifts, serve this building. Matte shells and converter-slag shells are dumped into heavily con¬structed flat-bottom bins located on the south side of the converter aisle and 1.0 ft. above the floor. The material is broken by ball and by hand, shoveled off into ladles for unloading on to the reverberatory charge floor, and charged into the furnace as previously mentioned.

Jan 1, 1934

By K. C. Gilbart, Edgar Stansfield

One of the most striking features of the coal series passing from peat through brown coal, lignite, etc., up to anthracite is the gradual reduction of moisture content with the increased coalification of the original plant material. Thus drained peat from a bog may contain 90 per cent water, brown coal contain 50 per cent, lignite 30 per cent, while a bituminous coal may contain only 1 per cent moisture. Moisture, therefore, is one of the important factors to be considered in coal classification, especially with the lower rank coals. With bituminous and higher rank coals the moisture content is less satisfactory for classification; it may even pass a minimum value and then increase with increasing rank to anthracite and superanthracite. Coal in an undisturbed seam contains moisture which is an integral part of the coal, but it may also be wet with free, underground water percolating through the seam. Only the former must be considered in evaluating the moisture content of the coal for classification purposes; this will be called the "true moisture" of the coal. When the seam is mined and sampled the sample taken may show the true moisture; on the contrary, it may contain in addition free mine water or, especially in dry, well ventilated mines, it may contain less than the true moisture. Coal contains unstable organic compounds which may decompose, with the production of moisture, when the coal is exposed to air at ordinary temperatures, or is heated with or without exposure to air. The potential moisture of a coal therefore is higher than its actual moisture. The lower the rank of the coal, the greater its instability, as a rule, and the greater the care necessary to avoid oxidation or decomposition in any investigation of moisture content. The majority of coal workers have preferred, on account of the difficulty in evaluating the true moisture of a coal, and for other reasons, to classify coals by analyses calculated to the dry-coal basis. A number of workers familiar with lower rank coals have recently insisted that the classification of such coals can be satisfactory only if analyses on the moist-coal basis are employed. The moisture-holding capacity of coal is therefore intimately connected with coal classification, and in this paper a procedure is outlined for determining the true moisture of a coal,

Jan 1, 1932

By H. Jehn

Like some other Pt-group metals palladium shows a low but considerable solid solubility of oxygen, which was found already from oxidation studies. The oxygen solid solubility of palladium in equilibrium with gaseous oxygen has been investigated at 900 - 1300 °C in oxygen (665 mbar) and air by gassing and analyzing polycrystalline samples. The 0-concentrations range from 40 to 90 ppm and decrease with rising temperature. The isobaric solubility can be represented by the least-squares fit log c0 = 0.5 log p02- 0.32 + 920/T (c0 in wt. ppm, p02 in mbar, T in K). The thermodynamic data of the exothermic solution reaction are calculated to ?H°= -17.6 kJ?mol-1 and ?S° -76.5 J?mol ? K-1. The behaviour of palladium in an oxygen atmosphere is characterized by the simultaneous reactions of the solution of oxygen in the metal and the formation and evaporation of volatile oxides besides the pure metal evaporation.

Jan 1, 1984

Between July 10 and August 15, 1918, the Secretary of United Engineering Society, of Engineering Foundation, and of Engineering Council visited 17 cities which are headquarters for large numbers of engineers. His mission was to tell men in all branches of the profession about "Centralized Activities of National Engineering Societies." Stops were made at Denver, Salt Lake City, Reno, San Francisco, Sacramento, Portland, Seattle, Spokane, Anaconda, Butte, Duluth,

Jan 10, 1918

By C. W. Spencer, J. T. Smith

GRAIN-BOUNDARY surfaces are penetrated by a liquid phase when the liquid-solid interfacial tension is less than one-half the tension of the grain-boundary surfaces. Grain growth may occur in the presence of this liquid phase. burke1 reports that grain growth of this nature has been observed in two-phase ceramic systems. He suggests that the presence of a grain-boundary liquid may accelerate or decelerate the

Jan 1, 1963

By P. C. Hodges

WHILE there is very little romance connected with the operation of a stone quarry, yet to those who have participated in the growth and development of a business that has been a pioneer in its field and that FIG. 1.-LOCATION OF PROPERTY OF MARBLE CLIFF QUARRIES COMPANY. has been in continual operation two-thirds of a century there is bound to be a background of experience, which if properly capitalized, brings progress as well as satisfaction in its accomplishment.

Jan 1, 1936

By Edward C. J. Urban

The nature of certain pernicious dusts commonly encountered in the removal of iron ore from the underground mines of the Lake Superior district is recognized, and appropriate measures for the protection of individuals subjected to these dusts have been applied in most mines for more than 10 years. Undoubtedly the principal concern has been demanded by dusts that contain as a constituent silicon dioxide in its free or uncombined state, the mineral we all know as quartz or chert. Investigators1 agree that among the factors that determine injurious exposure are: the composition of the dust, the concentration suspended at the breathing level and the duration of the exposure. We have on hand data that describe the experience of several underground iron-ore mines in the Upper Peninsula of Michigan and Wisconsin in regard to these factors, which in a large measure also reflect the general experience of the other mines of the area. We believe that a discussion of these data will indicate the effectiveness of the dust-control methods that have been considered good practice and that have been employed over a long period of time. A silicosis-prevention program was ini- tiated by the iron mines of the Upper Peninsula in 1934 and records of mine dustiness are available from that date to the present time. For dust conditions previous to 1934 the results of observations conducted in other industries can be utilized together with local information pertaining to the development and initial application of rock-drilling equipment. Development of Rock DriI,I.s Thc earliest percussion rock drill that later had any industrial use was patented in this country in 1851.2 This machine was later modified and improved in many respects but its Piston-Type design remained standard for drilling equipment in most mines for the next 63 years.3 The piston drill was operated either by air or by steam. It employed a solid drill steel, fastened directly to the reciprocating piston. The drilling was done dry except in holes directed at an angle below the horizontal. For these water was manually injected into the hole and the pumping action of the rod expelled the sludge. The dry cuttings from drillings inclined above the horizontal fell from the hole by their own weight. A development of major importance from the standpoint of dust generation and control occurred with the invention by J. G. Leyner of a hammer-type rock drill that embodied the essential feature of a drill steel with a hollow core. His patent was secured in 1897. The machine was a radical departure in drilling method. The steel was held loosely in a chuck while

Jan 1, 1949

THE refining period of an open-hearth heat blends imperceptibly into the finishing period, during which final adjustments are made in slag composition, in bath action and temperature, and in composition of the steel, in order to prepare it for casting into ingots. Operations must be governed by the consideration that alterations in the character of the heat during the finishing period must be held to a minimum. In a broad sense, the finishing and deoxidation period of a heat may be said to begin when the action of the last ore addition has ceased, and to end when the teeming of the ingots is completed. INGOT STRUCTURES A survey of the relative advantages and disadvantages of different types of ingot structure is required because deoxidation treatments during the finishing period control the amount of gas evolved during solidification and consequently determine the type of ingot structure. Four classes of ingots are recognized, depending upon the degree of deoxidation to which the steel has been subjected. These types are killed, semikilled, capped, and rimmed; typical examples of their structures are represented by ingots 1, 2, 5, and 7, respectively, of Fig 9-1. The actual ingots from which these cross sections were sketched were all poured to the same height (indicated by the dotted lines) in the same type and size of bottle-top molds. The eight drawings of the figure represent selected types of ingot structure in a continuous series from "dead killed" to "wild," resulting from variations in the total quantity of gas evolved, from none at all to copious amounts, during solidification of the steel in the mold. Killed and semikilled steels are adjacent at the "quiescent" end of the ingot structure series where only small amounts of gas are evolved. The term "quiescent" describes the action of the molten metal during and subsequent to the teeming of killed and semikilled steels. Capped and rimmed steels are adjacent at the

Jan 1, 1951

By C. G. Dunn, P. K. Koh

The primary recrystallization textures of 11 single crystals cold rolled 70 pct were determined. The effect of crystal orientation on recrystallization behavior was investigated also and found to be large. An exception was found to the relationship that strong components of the recrystolliza-tion texture are rotated from the cold rolled texture by 30° about <110> axes, but generally this relationship was found to hold quite well. Evidence supporting oriented nucleotion was found and discussed in terms of probable active slip systems and <110> edge dislocations. THE present paper is one of a series&apos;.&apos; on recrys-tallization phenomena in cold rolled 31/4 Si-Fe single crystals and is mainly concerned with the textures produced on recrystallizing from stable end orientations. Data for the cold rolled textures of the crystals used have been reported by Koh and Dunn." Their results showed that the sharpness of the cold rolled textures varied throughout the range of stable end orientations and that the tendency to re-crystallize was related to the sharpness of the cold rolled texture, wherein the rate of recrystallization increased and the size of recrystallization grains decreased with decreasing sharpness of the cold rolled texture. In the project under consideration the cold rolled crystals involved a range of initial orientations that, together with those studied earlier,&apos; provide information on several points. The first point is whether the recrystallization texture from a (111) [112] cold rolled texture, a stable end orientation that can be approached from different directions, correlates in any way with the initial orientation before cold rolling, or whether the recrystallization texture is entirely determined by the observable features of the cold rolled texture. The second point involves a preliminary study to see if the main components of the recrystallization textures correlate with the most probable active slip systems. The third point is to determine what effect departure from slip on one slip system has on the tendency to recrystallize. Experimental Procedure Nine specimens from a previous investigation and two additional ones from thicker stock (lot D) but of similar composition to the others were used in the present work. The latter two crystals, like the nine, were cold rolled to a reduction in thickness of 70 pct and the amount of widening was determined. Depending on their primary recrystallization behavior, the cold rolled crystals were given short or long anneals at temperatures of 980°C or higher. Table I summarizes the data on initial orientations, the textures obtained by cold rolling, and the anneals given to provide samples for the present work. Fine grained specimens were thinned to 0.002 in. thickness and placed in an integrating specimen holder. Chart recordings using a transmission X-ray method and MoKa radiation were obtained for diffraction from (110) planes. This method,&apos;,3 which gives data for all of the pole figure except a central region of 30" radius, proved sufficient to give generally five, and sometimes six, of the six possible pole concentration areas of any one component of the texture. These data, therefore, were generally adequate for a positive identification of each component present. The first texture obtained for specimen B-2 was poorly defined because of too coarse a grain structure and therefore too few crystals in each component for satisfactory X-ray reflections. The same

Jan 1, 1957