Search Documents

By M. A. Hunter

This paper gives the results of an investigation of the specific resistance and temperature coefficient of the electrical resistance of nickel and its important alloy, monel metal. For most of the pure metals, the temperature coefficient of resistance is approximately 0.004 per degree centigrade at 20" C. Nickel and iron, however, are exceptions. This property is important as it gives us good material for the construction of thermometers and other instruments involving electrical control. A summary of information on this subject has been publishcd by the Bureau of Standards.l The present experiments antedate this publication by several years and as the information obtained is not contained in it, the results of the experiments arc published as additional information. Electrical Properties of Pure Nickel It is generally conceded that the lowest values for electrical resistance are obtained in the purest metal. In the case of nickel, the best material obtainable is electrolytic nickel, which contains approximately 99.80 per cent. nickel, 0.15 per cent. iron, and 0.05 per cent. copper. Any cobalt that may be present is included in the nickel figure. If the elcctrolStic sheet has been deposited without intermission, it is possible to cut a section from the sheet and roll it into wire without melting. By this means a nickel wire may be obtained that is uncontaminated by any of the impurities always taken up by nickel during melting. Two samples of nickel wire obtained from different electrolytic nickels had the follolving electrical resistance and temperature coefficient of electrical resistance: Specific Temp. CofEE. Sample MateRial ReSISTance peR Deg. C. NO. 1 Electrolytic nickel.................... 7.55 0.00550 NO. 2 Electrolytic nickcl ................... 7.60 0.00553 * Rensselacr Polytechnic Institute. Director of Research, Driver-Harris Co. Russell Sage Laboratory, Rensselaer Polyt,ecllnic Institute. 1 U. S. Bureau of Standards, Circular 100 (March, 1921).

Jan 1, 1923

By T. L. Joseph

BLAST furnaces are most efficient thermally when the C02 in the top gas is highest. Oxygen introduced in the air blast is converted to CO in the combustion zones. The extent to which CO, generated in front of the tuyères, is converted later to C02 depends upon the ratio of ore to coke in the charge and the degree to which C02, formed by reduction of iron oxides with CO, reverts to CO by the secondary reaction C + C02 = 2C0. About 300 to 400 lb. of carbon1 per ton of pig iron is normally involved in the solution-loss reaction or direct reduction of FeO with carbon, which produces the same over-all results; that is, lower C02 in the top gas. Riche has recently reported a reduction in fuel consumption at slower rates of blowing on two furnaces in spite of higher heat losses per ton of iron. Lower fuel consumption at slow operating rates was due to more complete reduction of the ore that resulted in higher C02 in the top gas and consequently more efficient use of carbon. Kinney3 has reported substantial savings in fuel as a result of crushing and sizing the ore charge. Improvements in practice brought about by sintering magnetite concentrates, flue dust and fine ores have been due to the establishment of conditions favoring more complete reduction of the ore in the upper part of the furnace. The extent to which oxides and fluctuations in composition in pig iron affect the quality of steel and finished product needs further study. There is evidence that more thorough preheating and reduction of the ore in the upper part of the furnace tend to give a better quality of iron. Bogatzkii4 found from laboratory work that the amount of oxygen enter-

Jan 1, 1936

By R. R. Webster, H. T. Clark

The side-blown converter has been investigated as a possible commercial process for the production of low nitrogen steel. During this work, two converters of 3-ton and 22-ton capacity were operated on a pilot plant basis for a total of 214 heats. The steel made in these converters was low in nitrogen and possessed good cold working properties. Some problems of converter operation remain to be solved. IN plants operating with a high iron capacity, sev-eral different refining methods are used in the conversion of the molten pig iron to steel. These include various ore practices in stationary and tilting open-hearths, the duplex process employing the Bessemer converter and open-hearth, and the Bessemer process. At J&L, a considerable part of the iron produced is handled by the Bessemer process, either alone or in conjunction with duplexing, and therefore an appreciable portion of the steelmaking research effort has centered about the method. This paper covers research work on the development of the side-blow converter for the commercial production of low nitrogen ingots and includes descriptions of the operation of a 3-ton and a 22-ton experimental converter at the Aliquippa Works. The refining of iron to produce steel requires the removal of a large portion of the carbon and silicon and the control of manganese, phosphorus and sulphur which are present in the iron in varying amounts. The first large-scale means of refining iron was the acid Bessemer process which was brought into use almost 100 yr ago. This method, using compressed air as the refining medium, accomplishes substantially complete removal of carbon, manganese and silicon. Phosphorus and sulphur are not affected but, by choice of an iron composition sufficiently low in these elements, a commercial product can be produced. Since the process will handle large tonnages rapidly, operates without external fuel and with a minimum of additional equipment, it quickly became the major tool in the early expansion of the steel industry. Later, the basic open-hearth process, by affording control of phosphorus and sulphur and by consuming the large quantities of steel scrap that were becoming available, forced the acid Bessemer process into a secondary position in the industry. During the past two decades the demand for steel to be used in cold forming and drawing operations has gradually increased. Bessemer steel, because of its work hardening and aging characteristics, is not as suitable for these applications as basic open-hearth steel, consequently the decline of the process was accelerated. More recently, because of changing economic conditions, this long range trend appears to have been arrested or perhaps reversed. Ingot production data for recent years furnishes only an incomplete picture of the importance of the converter in the American steel industry; open-hearth furnaces utilize large tonnages of blown metal for which no published statistics are available. Metallurgical Aspects The fundamental difference between Bessemer and open-hearth steels apparently lies not in the method of manufacture but, rather, in the differences in chemical composition of the two steels. It is further believed that the principal features distinguishing Bessemer from open-hearth steel are the higher nitrogen and phosphorus contents of the former. Evidence supporting this position is supplied by tests on laboratory induction furnace heats that were made to contain varying amounts of phosphorus and nitrogen but were otherwise similar to normal low carbon silicon-killed steels. Fig. 1, 2 and 3, summarizing the test results, are taken from G. H. Enzian's paper titled, "Some Effects of Phosphorus and Nitrogen on the Properties of Low Carbon Steels."' Fig. l indicates that phosphorus has a marked effect on the cold work embrittlement of steel as shown by the work brittleness test of Graham and Work.' In the low nitrogen steels, which as a group have the better cold working properties, the effect of phosphorus variations is the more pronounced.

Jan 1, 1951

By Kim C. Harden

INTRODUCTION The purpose of the following discussion is to present the state of the art of solution mining. Since the economics of a mining method ultimately determines its applicability and viability this presentation shall revolve around the costs of in- situ solution mining. First the assumed physical characteristics of the hypothetical ore body are described, followed by the appropriate operating assumptions. Then after a brief discussion on the type of surface plant to be used, the assumed project time tables and costs for Texas and Wyoming are presented. Finally, the economics of in-situ uranium leaching are analyzed through the use of discounted cash flow rate of return analysis. ORE BODY CHARACTERISTICS The assumption of the ore body characteristics is probably the most variable portion of this discussion. The characteristics that have been used are based mainly on state of the art technology, however, consideration of the most common depths of ore, ore thicknesses, and permeabilities also influenced these assumptions. In addition, it is assumed that these assumptions are equally applicable to Texas and Wyoming. The average grade of the ore is assumed to be .09% U308 with no apparent disequilibrium. The average thickness of ore is 2.29 m (7.5 ft) which results in an average grade-thickness (GT) of .675. The assumed depth to the top of the ore is 121.92 m (400 ft), the ore density is placed at 1.78 gm/cc (18 cu ft/ton), the porosity is estimated to be 28% and the permeability 1 darcy. These assumed ore body characteristics are shown in Table I. In addition, it is specified that the costs to be later discussed are based on a minimum GT cut-off of 0.15. It is more common to use GT cut-offs of 0.30 to 0.50 but GT cut-offs as low as 0.15 in conjunction with a minimum grade of 0.05% U308 have been used in the past with success and is considered state of the art. The ultimate percentage of uranium recovered from the ore is left to the discretion of the reader since the costs and economics are based on pounds recovered by the surface plant. OPERATING AS.SUMPTIONS An annual production rate of 200,000 lbs U308!yr was chosen for this example. In order to maintain this production rate, based on the ore body characterized above, a flow of 4731 liter/min (1250 GPM) with a recovery solution grade averaging .039 gm U308/liter is assumed. A regular 5 spot well field pattern is used with a well spacing of 21.5 m (70.7 ft) between like wells and 15.24 m (50 ft) between unlike wells. This well spacing gives each well an area of influence equal to 232.25 sq m (2500 sq ftl. An excess wells factor of 1.17 is used to estimate additional monitor wells and well field boundary wells. Each production well is expected to yield an average flow rate of 37.85 liter/min (10 GPM). In addition it is assumed that the ore body has a good shape in that it is not tenuous and narrow but has at least an average width of 200 ft. The process chemistry required for this ore body is assumed to be based on the sodium carbonate System- Oxygen is the chosen oxidant. Sodium chloride elution followed by precipitation with hydrogen peroxide makes up the remaining portion of the process. A fluidized up-flow ion exchange system is specified. The operating assumptions are listed in Table II. Restoration of the ore body shall be assumed to be accomplished through the use of ground water flush. Other methods may be considered as having to fall within the costs estimated for a ground water flush in order to be economic. In Texas it is assumed that a high capacity disposal well (200 GPM +I is required and in Wyoming evaporation ponds covering approximately 35 acres are to be used. No specific cost has been given to restoration. Instead only the additional capital investment for restoration equipment is given. Then, one year of restoration operating expense is estimated and included as the operating expense for one year beyond the last pound of U308 produced. It is also assumed that restoration will be pursued in the mined out areas of the ore body contiguous with ongoing production.

Jan 1, 1980

By John C. Kleiber, George M. Meisel

From time to time since the initial installation of an experimental flotation section in 1940, Permanente Cement Co. has made efforts to beneficiate the low-grade limestone fraction which occurs in its deposits at Permanente, Calif. The encouraging results outlined in this article are the result of Permanente's latest effort. THE PERMANENTE LIMESTONE AND THE REASON FOR ITS BENEFICIATION The Permanente deposit is a sheet of Calera limestone over 700 ft thick lying within the Franciscan sediments of the San Francisco peninsula. Limestone suitable for cement manufacture underlies, overlies, and is interbedded with low-grade limestone and chert. Andesite intrusions are found as a secondary gangue. The limestone is identified as follows:

Jan 3, 1964

By Zay Jeffries

It has been known for centuries that iron and steel could be hardened by cold hammering and that the metal could be restored to the normal condition by heating to a red heat arid cooling, either rapidly or slowly with nearly pure iron, but slowly with steels containing considerable carbon. The art of tempering steels is also very old. When a medium- or high-carbon steel is quenched from a cherry-red heat, the hardness is increased; this hardness can be reduced by heating to various temperatures below the lower thermal critical point,, which is near 700" C. The present paper will not consider these old and well known changes in iron and steel below the thermal critical range but will confine itself to the more unusual changes, some of which have been studied recently. Stromeyer,1 for example, In 1886, reports that both working steel and heat treatment of steel in the blue-heat range arc highly injurious. Recently, however, some metallurgists believe that the straiglltening of warped steel forgings at a blue heat produces a beneficial effect on the metal2 The Engineering Division of the National Research Council has constituted a committee on Physical Changes in Iron and Steel below the Thermal Critical Range, which has the following personnel: K. R. -Abbott, H. C. Boynton, William Campbell, J. V. Emmons, F. B. Foley, H. J. French, H. M. Howe, Zay Jeffries (chairman), F. C. Langenberg, J. A. Mathews, P. D. Merica, A. H. Miller, J. H. Nelson, G. A. Reinhardt, W. E. Ruder, H. F. Wood. This committee is studying several aspects of the physical changes in iron and steel. The results, reported in the literature and obtained by recent experimentation, will be given; this will be followed by a general theoretical discussion of the more important

Jan 1, 1922

By Zay Jeffries

It has been known for centuries that iron and steel could be hardened by cold hammering and that the metal could be restored to the normal condition by heating to a red heat arid cooling, either rapidly or slowly with nearly pure iron, but slowly with steels containing considerable carbon. The art of tempering steels is also very old. When a medium- or high-carbon steel is quenched from a cherry-red heat, the hardness is increased; this hardness can be reduced by heating to various temperatures below the lower thermal critical point,, which is near 700" C. The present paper will not consider these old and well known changes in iron and steel below the thermal critical range but will confine itself to the more unusual changes, some of which have been studied recently. Stromeyer,1 for example, In 1886, reports that both working steel and heat treatment of steel in the blue-heat range arc highly injurious. Recently, however, some metallurgists believe that the straiglltening of warped steel forgings at a blue heat produces a beneficial effect on the metal2 The Engineering Division of the National Research Council has constituted a committee on Physical Changes in Iron and Steel below the Thermal Critical Range, which has the following personnel: K. R. -Abbott, H. C. Boynton, William Campbell, J. V. Emmons, F. B. Foley, H. J. French, H. M. Howe, Zay Jeffries (chairman), F. C. Langenberg, J. A. Mathews, P. D. Merica, A. H. Miller, J. H. Nelson, G. A. Reinhardt, W. E. Ruder, H. F. Wood. This committee is studying several aspects of the physical changes in iron and steel. The results, reported in the literature and obtained by recent experimentation, will be given; this will be followed by a general theoretical discussion of the more important

Jan 1, 1922

By AIME AIME

COUNCIL.* PRESIDENT OF THE COUNCIL. D. W. BRUNTON DENVER, COLO. (Term expires February, 1910.) . VICE-PRESIDENTS OF THE COUNCIL. J. PARKE CHANNING NEW TORE, N. Y. FREDERICK W. DENTON PAINESDALE, MICH. JOHN B. FARISH DENVER, COLO. (Term expires February, 1910.) W. C. RALSTON SAN FRANCISCO, CAL. IV. L. SAUNDERS NEW TORE, N. Y. H. V. WIINCHELL ST. PAUL, MINN. (Term expires February, 1911.)

May 1, 1909

By AIME AIME

COUNCIL PRESIDENT OF THE COUNCIL. D. W. BRUNTON DENVER, COLO. (Term expires February, 1911.) VICE-PRESIDENTS OF THE COUNCIL. W. C. RALSTON SAN FRANCISCO, CAL. W. L. SAUNDERS NEW YORK, N. Y. H. V. WINCHELL ST. PAUL, MINN. (Term expires February, 1911.) BENJAMIN B. LAWRENCE NEW YORK, N. Y. JOSEPH W. RICHARDS SOUTH BETHLEHEM, PA. ALBERT SAUVEUR CAMBRIDGE, MASS. (Term expires February, 1912.)

Mar 1, 1910

By AIME AIME

. COUNCIL.* PRESIDENT OF THE COUNCIL. D. W. BRUNTON DENVER, COLO. (Term expires February, 1911.) VICE-PRESIDENTS OF THE COUNCIL. W. C. RALSTON SAN FRANCISCO, CAL. W. L. SAUNDERS : NEW YORK, N. Y. H. V. WINCHELL ST. PAUL, MINN. (Term expires February, 1911.) BENJAMIN B. LAWRENCE NEW YORK, N. Y. JOSEPH W. RICHARDS SOUTH BETHLEHEM, PA. ALBERT SAUVEUR CAMBRIDGE, MASS. (Term expires February, 1912.)

Apr 1, 1910

By AIME AIME

COUNCIL.* PRESIDENT OF THE COUNCIL. D. W. BRUNTON DENVER, COLO. (Term expires February, 1910.) VICE-PRESIDENTS OF THE COUNCIL. J. PARKE CHANNING NEW YORK, N. Y. FREDERICK W. DENTON PAINESDALE, MICH. JOHN B. FARISH DENVER, COLO. (Term expires February, 1910.) W. C. RALSTON SAN FRANCISCO, CAL. W. L. SAUNDERS NEW YORK, N. Y. H. V. WINCHELL ST. PAUL, MINN. (Term expires February, 1911.)

Mar 1, 1909

By L. J. Cabri

The calculation of metallurgical balances for precious metals is very dependent on a precise mineralogical understanding of the distribution of each element. Determination whether the precious metals occur as dilute solid solutions in major minerals is not always easy because of the relatively high levels of detection (9200-500 ppm) of the precious metals by the most common methods of in-situ analysis (e.g. electron microprobe). Particle Induced X-ray Emission (PIXE) analysis of sulfides from Izok Lake, N.W.T., Canada and from the Hilton mine, Mount Isa, Australia with a proton beam (proton microprobe) confirms solid solution of Ag in chalcopyrite from both deposits. In addition, chalcopyrite and sphalerite from Izok Lake both contain indium.

Jan 1, 1984

By AIME AIME

PRESIDENT OF THE COUNCIL. D. W. BRUNTON DENVER, COLO. (Term expires February, 1911.) VICE-PRESIDENTS OF THE COUNCIL. W. C. RALSTON SAN FRANCISCO, CAL. W. L. SAUNDERS NEW YORK, N. Y. H. V. WINCHELL MINNEAPOLIS, MINN. (Term expires February, 1911.) BENJAMIN B. LAWRENCE NEW YORK, N. Y. JOSEPH W. RICHARDS SOUTH BETHLEHEM, PA. ALBERT SAUVEUR CAMBRIDGE, MASS. (Term expires February, 1912.)

Nov 1, 1910

By AIME AIME

COUNCIL.* PRESIDENT OF THE COUNCIL. D. W. BRUNTON DENVER, COLO. (Term expires February, 1910.) VICE-PRESIDENTS OF THE COUNCIL. J. PARKE CHANNING NEW YORK, N. Y. FREDERICK W. DENTON PAINESDALE, MICH. JOHN B. FARISH DENVER, COLO. (Term expires February, 1910.) W. C. RALSTON..: SAN FRANCISCO, CAL. W. L. SAUNDERS NEW YORK, N. Y. H. V. WINCHELL ST. PAUL, MINN. (Term expires February, 1911.)

Jun 1, 1909

Jan 1, 1969

By Matti J. Saarivirta

Two new precipitation hardening copper-base alloys, Cu-1.5pct Ti-2.5 pct Sn and Cu-1.5 pct Ti-2.5 pct Sn-0.4 pct Cr were developed. High strength and medium conductivity are obtained by solution annealing and subsequent heat treatment. Combination of solution annealing, cold working, and heat treatment increases the strength further. Good elevated temperature strength and ductility makes these alloys superior to copper-beryllium-cobalt alloys. A considerable amount of research work is being done throughout the world to develop new and improved copper-base alloys. In many cases, the object is to develop alloys having a combination of high electrical and thermal conductivities, and high strength. The problem is complicated by the fact that any alloying element added to increase strength, invariably decreases conductivity. Among the few commercial precipitation hardening type copper-base alloys, the Cu-Be-Co alloys are best known. These alloys are used in many applications that require good spring characteristics cornbined with high strength and moderately high electrical conductivity. They can be formed readily after solution annealing, then heat treated to obtain high strength and conductivity. Because of the relatively high cost of the Cu-Be-Co alloys, considerable research has been aimed at developing new lower cost alloys having similar properties. As far as is known today, the binary Cu-Ti alloy is the only one whose properties are

Jan 1, 1962

By Colman Goldberg

IT is customary to plot crystallographic planes or axes on a Wulff stereographic net which is ruled with parallels of latitude and meridians of longitude. If a single crystal is placed at the center of a sphere, the coordinates of a crystallographic plane or axis are the coordinates of the point where the axis intersects the sphere. The standard (HKL) projection is the projection for which the sphere is rotated so that the (HKL) pole is at the center of the projection. Schiebold and Sachs' and many others have published standard projections for the more important planes of a cubic crystal. With Tables I and 11, it is possible to plot any plane (HKL) of a cubic crystal on a standard (001) projection if the absolute values of the individual H, K, and L are nine or less, which is almost always the case. Using the methods outlined by Barrett,' the standard (001) projection can be rotated so that any arbitrary plane is at the center of the projection. The tables are believed to be important for two reasons: 1—The heretofore published standard projections usually are not of the proper size to fit the stereographic nets available. With these tables a standard projection can be made which will be of exactly the proper size for the available stereographic net. 2—With the tables, planes that do not appear on the previously published standard projections can be easily plotted. For these reasons, the tables are especially useful in the study of optical reflections from etched surfaces and can also be used to make a standard projection for the axis which is normal to the macroscopic surface. (This axis can be found by X-ray or optical methods.) Then if the crystal is etched, the effect of the etchant can readily be determined by comparing the latitude and longitude of the reflecting planes (as determined with an optical goniometer) with the standard projection that has been prepared. Use of the Tables Fig. 1 shows the meridians and parallel which have been designated as zero longitude and latitude. The tables themselves are self-explanatory. The

Jan 1, 1953

BURKE BAKER, Philadelphia, Pa. (written discussion*).-The small briquetting plant of the American Briquet Co., at 25th Street and Washington Ave., Philadelphia, was built primarily as a demonstration plant. Its output per hour is 4 tons of 2-oz. briquets, which have been retailed in the, vicinity during the year the plant has been in operation. They have proved very acceptable for use in ranges, heaters and grates in-home, and in steam heating plants in apartment houses and hotels. They have not been sold for power purposes, although satisfactory tests have been made in. this field. Anthracite silt is used and is shipped direct from breaker or washery, the only preparation it receives being the removal f excess moisture by means of a Ruggles-Coles rotary dryer. Care is taken, however, to purchase silt containing less than 18 per cent. ash. The method is covered by U. S. Patent No. 941454, issued to Chas. E. Hite, and is known as the "emulsion process." The binder, which is the, basis of the patent, is composed. of 0.5 per cent. cornstarch or wheat flour; 1 per cent. asphaltum or hydrolene, and 6.5 per cent. water, on the weight of coal dust. It is prepared in a tank equipped with paddle agitators and heated by steam jets. The starch and water are first made into a paste by being brought to the boiling point with live steam; the melted asphaltum is then introduced and thoroughly beaten into the paste by the agitators. This rapid stirring breaks. the hot asphaltum into minute particles which are distributed through the paste, producing a smooth chemical emulsion. This emulsion, when dried, is not soluble in water. The binder is mixed with the dry coal dust in a horizontal paddle mixer, 8 per cent. binder to the weight of coal being used. The resultant plastic mass is then discharged into the press, which is of the simple roll type. Since the binder is a liquid and is not sticky or gummy until

Jan 3, 1918

By CYRIL W., William Campbell, Henry M. Howe

THIS paper gives the results of an investigation of the behavior of the argentiferous cobalt-nickel arsenides of Temiskaming, Ontario, in roasting, made in the metallurgical laboratories of the School of Mines, of Columbia University in the City of New York. The ore was kindly given by the owners of the La Rose and Trethewey properties at Cobalt, Ontario, and Mr. E. J. Hall, Tutor in Assaying in Columbia University, has helped us much. I. OBJECT OF THE INVESTIGATION. The object of the investigation was to learn:- 1. The temperature at which the arsenic is most rapidly expelled; 2. The thoroughness with which it is expelled by prolonged roasting at this temperature; 3. The effect of adding charcoal (a) near the end of the roast and (b) at the beginning of the roast. II. NATURE OF THE ORE. The important ores mined in the Temiskaming deposits are native silver-with small amounts of dyscrasite (Ag6 Sb), argentite (Ag2S), pyrargyrite (Ag3SbS3)-smaltite (CoAs2), chloanthite (NiAs2) and niccolite (NiAs). Mispickel (FeAsS) and cobaltite (CoAsS) also occur in smaller quantities. The average composition of the ore shipped from this district for the first six months of 1905 -was: silver, from 4.1 to 4.8 per cent.; cobalt, from 6.9 to 8.2 per cent ; nickel, from 3 to 4.7 per cent ; and arsenic, from 30.9 to 34.6 per cent. The ore which we treated consists chiefly of smaltite ; In our laboratory-work

Jan 1, 1907

By F. George, W. Tice, M. Salkind

It was found that Al-A13Ni could be readily cold rolled perpendicular to but not parallel to the whiskers. Reductions of more than 98 pct were achieved without cracking by rolling perpendicular to the whiskers, whereas extensive edge cracking was noted after only 15 pct reduction when rolling parallel to the whiskers. The longitudinal and transverse tensile strengths were nearly doubled, and the longitudinal yield strength more than tripled by cold rolling 50 pct in a direction perpendicular to the whiskers. The whiskers exhibited some waviness (elastic bending) as a result of cold rolling, but at very high reductions (greater than 75 pct) whisker fracture and misalignment became significant. A fine dislocation substructure in the matrix consisting of cells attached to the whiskers was pro -duced by cold rolling. Most of- the substructure was readily removed by a 1-hr anneal at 500°C. Cold rolling was found to substantially reduce the thermal stability of the microstructure at 610°C but did not affect the stability at 500°C. FIBER and whisker reinforced composite materials promise significant improvements in properties over conventional materials. Before they find wide use, however, it will be necessary to understand the response of these highly anisotropic materials to common metalworking processes. Most of the nonmetal-lic fiber reinforced materials have very low elongations (a few pct or less) in the direction of fiber alignment. Thus, metalworking techniques such as rolling and forging would not be as broadly applicable to these materials. This investigation was initiated to determine how a composite system consisting of Al3Ni whisker reinforced aluminum responded to rolling, what changes in the microstructure occurred, and the effect of deformation on the mechanical properties. The composite material studied was produced by unidirectional solidification of the A1-Al3Ni eutectic alloy'-7 and consisted of 10 pct by volume of aligned whiskers of Alai in a matrix of aluminum. It should be pointed out that this system is not representative of all composite materials, and the results will therefore not be universally applicable. The A1-Al3Ni system is characterized by: 1) A strong fiber-matrix interfacial bond 2) A ductile matrix 3) A sufficiently low fiber content to allow significant plastic flow between fibers 4) Strong, completely elastic whiskers (tensile strength 400,000 psi, elastic modulus = 20 X 106 psi.1 These factors allow the material to be readily rolled perpendicular to the fibers. If the fiber-matrix bond were not strong, such a weak interface could fail during rolling. A measure of the ability of a composite to be rolled in the transverse direction can be obtained from noting the transverse tensile behavior. In the case of Al-Al3Ni,2 there is considerable ductility (15 to 30 pct). In the case of boron filament reinforced aluminum, for example, the transverse elongation is less than 1 pct,8 and the material could probably not be cold rolled as readily in that direction. EXPERIMENTAL PROCEDURE 3-in. diam ingots of A1-A13Ni eutectic were unidi-rectionally solidified in graphite crucibles. The starting materials consisted of 99.99+ pct pure nickel and aluminum, and the pure eutectic ingots were made with 6.2 wt pct Ni. The unidirectional solidification process (described in detail elsewhere1-3) consists of preparing a master heat of eutectic composition, remelting, and withdrawing the ingot vertically downward through the heat source at a controlled rate so that plane front solidification proceeds upward at a constant velocity. The resulting microstructure consists of 10 pct by volume of whiskers of very high aspect (length to diameter) ratio. The fiber lengths have not been measured because of the difficulty of detecting fiber ends9 but exceeds 104. There is some possibility that the fibers may be continuous within one grain. Flat sheet specimens 2¾ in. sq and approximately 0.2 in. thick containing whiskers parallel to the plane of the sheet and to one edge were used for this study. A1-A13Ni exhibits either a rod-like (high solidification rates) or a blade-like (low solidification rates) whisker morphology,1,3 and both types were studied. Rolling was accomplished using a two-high rolling mill at a speed of approximately 10 fpm. The rolling direction was either parallel to or perpendicular to the direction of growth (direction of whisker alignment). Reductions of from 0.002 to 0.03 in. per pass were used with the most common value being 0.005 in. per pass. Cold rolling of Al-Al3Ni to more than 98 pct reduction in thickness was accomplished with no intermediate anneals. In addition. a series of speci-mens was cold rolled 97 pct with a 1-hr, 500°C anneal in air after each 50 pet reduction. Tensile testing was accomplished using a Tinius-lsen four screw testing machine. Flat sheet specimens + in. wide and between 2 and 2; in. long with the thickness dependent upon rolling reduction, were used. The gage section was in. wide and 1 in. long. Strain was measured using a clip-on LVDT extensome-

Jan 1, 1970