Search Documents

By K. M. Rolls, J. Wulff, D. A. Colling

Solid-solution alloys of the Ta- Ti system containing up to 70 at. pct Ti were melted and fabricated into wire. Steady magnetic-field measurements of cold-worked wires at 4.2°K indicate that the resistive critical field increases smoothly with increasing titanium, reaching a maximum of 93 kG (J = 1 amp per sq cm) for a composition of about 50 at. pct Ti. The composition dependence of the resistive critical field indicates it is largely paramagnetically limited for alloys containing more than 35 at. pct Ti. For cold-worked wires the value of the critical current density, Jc , was found to be insensitive to composition changes for compositions in excess of 20 at. pct Ti. It was observed that Jc could be increased by final-size heat treatment at 400°C without altering the value of- the resistive critical field. Experimental data are used to calculate the electronic specific-heat coefficient and the "upper critical field" for the alloys studied. THE effect and importance of metallurgical structure on superconducting properties have been summarized by Livingston and Schadler.1 Specific work on solid-solution alloys such as Nb-zr2-7 and Nb-Ti5-7 have shown that critical current density (Jc) and superconducting transition temperature are structure-sensitive. Berlincourt et al.6,8,9 in their studies of transition-metal alloys find that Ta-Ti alloys remain superconducting at fields comparable to Nb-Ti alloys. 6,8 Transverse critical current tests of a Ta-10 at. pct Ti alloy10 and longitudinal critical current tests of a Ta-25 at. pct Ti alloy1' indicate that such alloys are capable of carrying high currents at intermediate fields (-40 kG). The work reported in the present paper was undertaken to explore the superconducting properties of further compositions in the Ta-Ti alloy system as well as the structure sensitivity of the superconducting properties. I) EXPERIMENTAL PROCEDURE Alloys were prepared by melting tantalum (Fansteel Metallurgical Corp., 99.96 pct purity) and iodide, crystal bar titanium (Foote Mineral Co., 99.92 pct purity) mixtures in an arc furnace on a water-cooled copper hearth using a tungsten electrode. Melting was accomplished in a purified, gettered argon atmosphere at pressures from 250 to 400 Torr. Each alloy was turned and remelted fourteen times to assure complete mixing of tantalum and titanium. Ex- cessive coring in the cast samples was, nevertheless, observed. This was somewhat reduced by annealing in vacuo at 1000°C for 13 hr. The ingots were then machined to 0.250 in. diam, jacketed in Type 304 stainless-steel tubing, and swaged to 0.140 in. diam. They were then drawn to 0.010-in.-diam wire. Alloys containing up to 70 at. pct Ti were readily cold-drawn to wire in this manner. Later experiments showed that oxygen additions up to -3000 ppm could also be cold-worked into wire. Test samples for superconductivity measurements in the 2-in, air-core Bitter solenoids of the M.I.T. National Magnet Laboratory were prepared from 10-in. lengths of 0.010-in.-diam wire, cleaned of residual wire-drawing lubricant. Current contacts were made by clamping clean copper tubing over both No. 18 current lead wire and the ultrasonically indium-tinned ends of the specimen wire.12 Potential leads of No. 32 copper wire were connected to the specimen by ultrasonic soldering in an indium bath. The potential lead separation was about 4 cm, corresponding to the circumference of the Bakelite rod to which the wire was affixed with half-mil Teflon tape. The final specimen configuration is shown in Fig. 1. Specimens were lowered into a liquid helium bath (4.2oK) in a double solenoid dewar and positioned so that the maximum magnetic field was oriented transverse to the wire axis of the gage section. Measurements were made by passing a current through the specimen at a preset solenoidal magnetic field. The current was increased until a 1-pv potential difference appeared across the gage section (1/4 µv per cm). At low magnetic fields, however, it was not possible to use this criterion because power-dissipation difficul-

Jan 1, 1967

By Harry Seltz

INTERMETALLIC compounds are formed in many binary metal systems. Some compounds are stable to their melting points, and others decompose at lower transition temperatures. Even those of the first class are dis-sociated in the liquid state, as indicated by the continuous for in of their solubility curves at their melting points1. While the lattice structures of some of these compounds have been determined, their thermodynamic properties have not been investigated. In this paper is described the determination of the free energy and heat of formation of the compound CdSb, which is of the first class mentioned above, melting congruently at 455° C. This compound shows a rhombic structure, and the lengths of the edges of the elementary cell containing four molecules are: a =6.52, b = 8.60, c = 4.16 A.2 There are three possible methods of determining the free energy of formation of a compound of this type. The first method, applying the third law of thermodynamics, requires the measurement of its heat capacity preferably to liquid hydrogen temperatures, and a calorimetric determination of its heat of formation. The second method involves the study of the equilibrium of the compound in some gas reaction, such as: CdSb + CO2 = CdO + CO + Sb From the known free energies of formation of CdO, CO2 and CO the free energy of formation of CdSb could be calculated. The third method measures the electromotive force of a galvanic cell in which the cell

Jan 1, 1935

By W. J. Taylor

Every one having practical experience in making heating-gas knows how much room there is for improvement,, in order to avoid not only the production of poor gas, when good gas is most wanted, but also the waste due to burning gas on top of the fuel-bed, and the loss of both time and fuel in cleaning.* The producer which I have recently designed, and with which I am now experimenting with every prospect of success, at the oreroasting kilns at Chester furnace, is intended to remove these difficulties as far as possible, and at the same time to be continuous in operation. I have not had it at work long enough to get beyond the stage of experiment; hence, I will only at this time explain it in a general way, and illustrate it with a drawing, promising a more elaborate paper if it becomes the practical success I anticipate. The features of the producer are : 1st. The round dome-shaped revolving bottom; and 2d. Metallic water-cooled walls in place of the usual brick lining. As shown in the drawing, the bottom has a sleeve, which fits over the air-admission pipe, coming up through the center of the

Jan 1, 1887

By John Gillie

PRioR to the year 1902 electricity was used in the Butte district only for lighting, for the tramming of ores on the surface, and for the electrolytic refining of copper. In that year the Canyon Ferry hydro-electric plant on the Missouri river, with a transmission line to Butte and Anaconda, was completed, and enabled the mining operators to purchase electric current in large quantities at reasonable rates, and its application and use in the various mining operations and reduction works proceeded rapidly. The principal applications of electric current in metal mining may be listed as follows: Compressing air for hoisting. Compreeaing air for rock drills and pneumatic tools. Pumping. Ventilating. Lighting. Tramming. Compressing air for blast furnaces and converters Running shop and miscellaneous motors. Compressed Air for Hoisting. The Anaconda Copper Mining Co. operates 22 mine shafts and plants at Butte. Of these, 15 are large plants and hoists, through which most of its ores are hoisted. In 1912 this company commenced using compressed air in place of steam, in operating a number of its large hoists, and at this date has 10 main hoisting engines and 10 auxiliary hoists driven by compressed air. The compressed air is furnished from a central plant containing six compressors, each having a capacity of 7,500 cu. ft. of free air per minute compressed to 90 lb. pressure in large receivers, and conducted by suitable pipe lines to the various hoists, the air being reheated before passing to the engines. Each of these compressors is driven by a 1,200-h.p. synchronous motor, directly attached to the drive shaft, and takes electric current at 2,200 volts. Two additional compressors are being installed,

Jan 1, 1914

By O. J. C. Runnals

The intermetallic compounds NpAl2, NpAl3, and NpAl have been prepared, and examined by X-ray diffraction methods. The compounds are isostructural with the corresponding U-Al compounds. NpAl3 is face-centered cubic with a = 7.785A and has the MgCu2 structure. NpAl is simple cubic with a = 4.2624 and has the AuCU3 structure. NpAl4 is body-centered orthorhombic with a = 4.428, b = 6.268, and c = 13.71A. The published description for the atomic positions in UAl, applies also to NpAl4 THE U-Al system has been examined by Gordon and Kaufmann.1 They identified the following intermetallic compounds: UAI2, UAl3, and a third, tentatively identified as UAl5. A structure analysis of the latter compound by Borie2 proved that the formula UAl4 was more consistent with the X-ray data. The crystal structures of UAl2 and UA have been reported by Rundle and Wilson.3 UAl2 was found to be isostructural with MgCu. The atomic positions in the simple cubic UA1, cell were found similar to those in the AuCu3 structure. Three analogous compounds exist in the binary system Np-Al. X-ray data for the compounds NpAl2, NpAl3, and NpAl4 are reported below. The neptunium used in the investigation was supplied through the courtesy of the Argonne National Laboratory as neptunium (V) nitrate. It was stated to have a radioactive content of 99.25 pct Np237. The impurity limits had been established by a spectrographic analysis given in Table I. Any titanium, boron, or bismuth impurity should be effectively removed during the fluorination of NpO2 to NpF4, and sodium, lithium, magnesium or strontium during the alloying procedure. The oxalate ignition technique, described by Westrum for the preparation of finely-divided reactive PuO2, was used.The neptunium (V) nitrate solution, containing 100 mg Np, was evaporated to dryness on oxalic acid crystals. The resulting oxalate was calcined to NpO, by heating in platinum at 650°C for 2 hr. An equimolar mixture of anhydrous hydrogen fluoride and purified hydrogen was passed over the NpO2 for 2 hr at 500°C. According to Fried and Davidson" the above fluorination conditions should produce the purple-black fluoride, NpF3 However, the light-green product showed only NpF4 lines on an X-ray diffraction pattern and contained only an estimated 5 pct of finely dispersed black NpF3 particles on microscopic examination. NpAl3: An intimate mixture of 50 mg of neptunium fluoride and aluminum powder (99.99 pct pure, —28 to $60 mesh) was heated to 900°C in a BeO crucible in vacuum by a tungsten coil for 2 hr, to allow the following reaction to proceed: NPF4 + 7Al + NpAl, + 4AlF. [1] The formation and sublimation of aluminum mono-fluoride in this system was verified from an X-ray diffraction analysis of the sublimate. The diffraction pattern was similar to one obtained in the aluminum reduction of UF4 to UF3,6 showing both Al and AlF3 lines. The resulting alloy was sintered at 1100°C for 1 hr. A powdered specimen of the crystalline product was sealed in a thin-walled quartz capillary for X-ray examination. The photograph was taken on a 14.32 cm General Electric powder diffraction camera, using filtered copper radiation. The films were calibrated in terms of a NaCl standard pattern. The wavelengths used in the calculations were 1.5418A for Cu K and 1.5405A for Cu K The powder diffraction pattern showed that NpAl is simple cubic with a = 4.262 % 0.005A, and is isostructural with UA13 where a = 4.27A1 or a =

Jan 1, 1954

By A. M. Gaudin

This year the American Institute of Mining, Metallurgical and Petroleum Engineers has chosen to give me its Robert H. Richards Award, a distinction which is widely regarded as the highest honor in the field of mineral engineering. I am deeply moved by this tribute, which suggests not only regard for my service to the profession but also the affectionate esteem of my fellow mineral engineers. You have made me happy at the prospect of the permanent association of my name with that of Robert Hallowell Richards and of the distinguished recipients of the award, Arthur Fay Taggart, Frank R. Milliken, John F. Myers, Edward William Englemann, C. Harry Benedict, Edward W. Davis and Arthur W. Fahrenwald. I wish to thank you all for an honor so generously bestowed. Professor Richards is known to us all as a legendary figure, and we can read about him in the Richards Memorial Volume of our Transactions. Some of us have even had the good fortune of knowing him. I count myself among those lucky few. In its intangible attributes the Award recalls those things for which Professor Richards stood: for Science in Art, for thoroughness, for meticulous accuracy, for bold imaginativeness, most of all for professional integrity. Now, as in his day, these attributes are central to an engineer's creed. They are appropriately needed in a formulation of a definition of the mineral engineering profession.

Jan 6, 1957

By M. W. BERNEWITZ

ALL live producers and manufacturers of metals and alloys are investigating new uses for their products. The tin and tin-plate industry is no exception. One-third of all the new tin mined and refined is consumed in making tin plate. Several billions of cans are each year made from tin plate for the preservation of nearly 200 kinds of food. There are more than 500 tin-plate mills or individual stacks in the United States, which country makes more tin plate than all other countries combined and exports large quantities. As much as 1,800,000 tons of till plate has been made in a year in this country, and 28.000 tons of tin has been used in this period for this purpose. In sonic years a third of the till is so consumed; in 1933 it was half of the supply.

Jan 1, 1935

By AIME AIME

At the Annual Meeting of the Institute, February, 1908, the following amendments to the Constitution were proposed for action at a future business meeting (see Trans., XXXIX, xxvii) To Art. II. After the first sentence of this Article, add the following sentence « These classes may be subdivided by the Council, according to profession, length of membership, nationality, or other conditions not inconsistent with the provisions of this article." To Art. III. In the first line, substitute " fifteen " for "ten " dollars. At the Annual Meeting of February, 1909, action upon these amendments was postponed to the next business meeting (see Bulletin No. 27, March, 1909, p. xiv). Of these two amendments, the first has been withdrawn, as unnecessary-the subdivision thereby authorized being already practicable without such amendment. The second amendment will be acted upon at the next Annual Meeting, February 15, 1910, and the Secretary has been instructed to call the attention of members to the subject in such a way as to secure a general vote upon it. A special circular, now being prepared by the Secretary, will shortly be sent to all members. Year Book of the Institute. The Year Book of the Institute for 1910 is sent to all members and associates with this issue of the Bulletin. In addition to the lists of members enrolled Jan. 1, 1910, and arranged both alphabetically and geographically, this annual contains lists of officers, council, corporation, past officers, meetings, and notices concerning publications; also the constitution and by-laws of the Institute, and blank forms for proposal of mem-

Jan 1, 1910

By RAY J. CORFIELD

IN a previous paper, "Electric Shovel Operation at Utah Copper Mine," which was read before the Western Division of the American Mining Congress, the problem of electrifying a fleet of steam shovels was described. This paper deals with the electrification of the haulage system which, when completed, will make the mining operation completely electric, with the exception of drilling operations which will continue to be performed by air. The general layout of the haulage system involves the use of heavy curves in addition to heavy grades of between 4 and 5 per cent. In a mining operation of this kind no trackage can be called permanent; this complicates the overhead construction somewhat and makes it necessary to design special forms of trolley construction, some of which will be described in detail below.

Jan 1, 1929

By W. A. Wall, R. L. Kidd

IN present-day flotation practice, grinding of the flotation feed is carried to extremely fine sizes, 70 to 80 per cent minus 200 mesh being customary. The greatest flotation losses occur in the coarsest and finest sizes, but the losses in the very fine sizes are, of course, much the more important because of the large proportion of fines in the feed. These losses are particularly high in zinc ores so a study of the effect of size on the flotation of sphalerite has been made. The mineral used in these experi¬ments was a pure sphalerite, especially free from copper, from the Joplin district in Missouri. The sizes coarser than 200 mesh were separated by screening, the sized mineral then being deslimed on a Wilfley table. The sizes finer than 200 mesh were obtained by water elutriation as described by H. R. Bradford (M. S. Thesis, University of Utah, 1932) ; particles finer than 6.5 microns could not be obtained with the apparatus used.

Jan 1, 1933

By E. Northcott, F. N. Oberg

By electrostatic separation, course Florida pebble phosphate, too lou-grade to find a ready market, can be upgraded to a satisfactory saleable product. Pebble running from 60 pct bone phosphate of time may be upgraded to 73 to 77 pct BPL depending on the mineralogical. structure of the pebble and the nature of the silica innpurity. High-grade concentrates from Florida pebble phosphate deposits have long been recovered by wet methods. When work was begun in the field, only the coarse pebble (generally +1 mm) was re- covered. In the 1920's a froth flotation process was developed to separate quartz from the finer phosphate fractions, but this method proved unsatisfactory for treating the intermediate fraction (—1 mm +35 mesh). Consequently various other processes were adapted, including agglomerate tabling and spiral separation of reagentized feed. Today the three processes are used—washing and screening for coarse pebble, tabling or spiraling for intermediate sizes, and flotation for —35 mesh material.

Jan 1, 1959

By J. M. Smith, D. Kunii

Effective thermal conductivities of sandstones filled with stagnant fluids were measured using a steady-state technique. Data were obtained for seven sandstone samples, taken from four different locations and ranging in permeability from 18 to 590 md. The measurements with gases (helium, nitrogen, air and carbon dioxide) covered a pressure range from 0.039 psia to 400 psig. Data were taken for four liquids — n-heptane, methyl alcohol, 79.8 weight per cent glycerol-water solution and pure water at atmospheric pressure. The experimental results were used to evaluate the theoretical equations for predicting stagnant conductivities developed earlier 4 The low-pressure measurements permitted evaluation of the consolidation parameter bpDp/ks (necessary to utilize the theory) for the various types of sandstones. Using these characteristic values, the tbeoretical equations correlated well with the experimental conductivity data for the several fluids and rock samples. INTRODUCTION An aspect of heat transfer in solid-fluid systems of considerable current interest is the effective thermal conductivity of porous media. The stimulus for study of the subject arises from the need for sound procedures for designing thermal methods of petroleum production. The general system occurs when there exists a flow of fluid through the pores of the solid material. However, a logical starting point in developing a theory for predicting the effective thermal conductivity in the general system is to attack the special case when the porous solid is filled with stagnant fluid. Since the flow rates anticipated in thermal production processes are very low, such stagnant conductivities k,O are also of practical significance. Kunii and Smith4 recently reviewed the existing data for stagnant conductivities and proposed a theory for heat transfer in porous rocks. This leads to equations for predicting the stagnant conductivity as a function of the properties of the fluid and solid phases. The existing experimental information1-3,5,7,8 covered a range of porosities and agreed well with the theory. However, the available data were insufficient to examine critically the effects of two important properties on koe, — the thermal conductivity of the fluid and the pressure. The objectives of the present study are twofold: (1) to measure the effect on koe of (a) the pressure for gases, and (L) the thermal conductivity of the fluid kg for bloth gases and liquids; and (2) to determine for rocks of different porosities and permeabilities the apparent solid conductivity ks and the consolidation parameter bpDp/ks required in applying the theoletical equations. Measurements extrapolated to zero pressure are helpful in evaluating ks and the consolidation parameter. However, the extrapolations must be based upon data obtained at low pressures because in small pores the molecular conductivity of the fluid may be unusually depressed. This occurs when the mean free path of the molecules is of the same order of magnitude as the pore diameter, that is, in small-diameter pores at low pressures. The phenomenon has been studied recently by Schotte6in beds of unconsolidated fine particles. With particles in the size range of 45 to 200 microns, a significant reduction of kg with pressure was found even at absolute pressures greater than 1 atm. In the sandstones employed in the present investigation, pore diameters lower than those experienced by Schotte are likely, so that the effect would presumably be greater. SCOPE OF MEASUREMENTS Stagnant conductivities were measured for four types of sandstones using a total of seven samples. The characteristics of the samples, including porosity and permeability values, are given in Table

By P. D. Zemany, G. W. Sear, B. W. Roberts

Vanadium metal is embrittled by hydrogen at a temperature as low as 250°C when held in the presence of manganese metal and water vapor in a rough vacuum. It is established that the property changes are caused by the catalytic decomposition of water vapor at the vanadium surface and the diffusion into and solution in the vanadium of the resultant hydrogen. It is found that manganese is a necessary component of the catalyst. The manganese is transported in the vapor phase by an unknown molecule. A deuterium tracer experiment demonstates the role of water vapor in the embrittle-ment process. VANADIUM metal foils were observed to become embrittled' at a temperature of about 300 °C when held in the presence of manganese metal and a small amount of moist air, This paper describes the investigation to find the embrittling agent and an understanding of the relatively low temperature reactions that are involved. Experimental The vanadium metal foil used was prepared by cold-rolling and pack-rolling 32 mil sheet" in a series of steps down to 1 mil foil. The original observation was confirmed by sealing vanadium foils of 3 x 10 sq cm into individual Pyrex tubes with manganese powder† and a con- trol tube containing only the vanadium foil. These tubes were evacuated to 10 -5 mm Hg without baking and sealed. After heat treatment for 200 hr at 300°C, the control foil showed no change in duetility, whereas the foil contained in the manganese— containing tube was embrittled. The visual appearance of each was unchanged. A series of Pyrex sample tubes, about 2.5 cm diam and 25 cm long, were prepared, each containing a 3 x 10 sq cm piece of foil and 5 g manganese powder at the lower end of the tube. By reducing the time of anneal and the temperature of these samples, it was found that embrittlement could be created at 250°C in a time as short as 1 hr. Since the vanadium metal used here has been drastically cold-worked by rolling, it is assumed that it contains a maximum number of dislocations. To check the possible necessity of dislocations in this low temperature reaction, a vanadium foil sample was annealed in Vycor for 2 hr at 800°C to re crystallize and reduce the dislocation concentration. Metallographic examination showed grains which were not visible before annealing. The embrittlement procedure was carried out at 300°C and 3 hr. Upon checking the foil no embrittlement was observed. Further experiments demonstrated that about 6 hr at 300°C are required to create embrittlement in the foil. This delay in the onset of embrittlement in the vanadium foil suggests but does not prove that dislocation channels play a role in the embrittlement phenomena. If manganese metal is necessary for this low temperature embrittlement, do other elements in the transition metals group yield the same result? To check this qualitatively, a group of elements of similar atomic radii were obtained and sealed as before into Pyrex tubes with a sheet of vanadium foil. These tubes were annealed at 250°C for 6 hr and included (with radii)-2 A1 (1.4A), As (1.25A), Be (1.2A), Co (1.25A), Cr (1.45A), Cu (1.25A), Fe (1.25A), Ga (1.2A), Ge (1.25L%), Mn (1.3A), Ni (1.25A), Si (1.2A), Ti (1.45A), Zn (1.3A), air, H,O, 10 cm Hg of dry hydrogen, and MnO, powder. Upon testing the above sample foils for brittleness, only the manganese-containing tube yielded a brittle foil. Manganese Transport—To eliminate contact of manganese metal powder and vanadium foil, sample tubes were prepared with fritted glass barriers. The embrittlement reaction was still found to occur. Thus, the mode of transfer of manganese is certainly vapor transport. A vanadium foil was embrittled by this mechanism in an evacuated Pyrex tube for 8 hr at 300°C. By means of X-ray fluorescence analysis,' the amount of manganese added to the surface was established at 5 ±2 x 10 -6 g per sq cm. Since the average rate of manganese deposition is known, an effective average pressure of an assumed carrier compound can be computed. ___ P = M/T v2p mkT

Jan 1, 1959

A High-speed Dilatometer and the Transformational Behavior of Six Steels in Cooling. By Arthur L. Christenson, Edward C. Nelson and Clarence E. Jackson. (With discussion).................................606 Dilatometric Studies of the Graphitization of Cast Iron. By N. A. Ziegler. With discussion) 627 An Interferometer Type of Dilatometer and Some Typical Results. By- L. '4. WIlley and W. L. Fink. (With discussion).........................642 The meeting was held in the Pine Room of the Statler Hotel, Cleveland, Ohio, on Tuesday afternoon, October 17, 1944. The chairmen were F. M. Walters, Jr. and Howard Scott. Introduction F. M. Walters, Jr.—The principal advantages of the dilatometric method perhaps are two, as compared with the method of thermal analysis. One is that the dilatometric method can be applied with a large variety of rates of heating and cooling, whereas thermal analysis—that is, the study of the transformational characteristics by means of heat evolution—is limited to the rates of heating and cooling that reveal the evolution of heat. The dilatometer can be used for the study Of reactions at zero rates of heating and cooling; that is, isothermal reactions. As you will hear this afternoon, the rates have been pushed up as far as 500°C. a second. The other advantage is that the dilatometric method shows that a two-phase region is a two-phase region, whereas the thermal analysis merely reveals the temperature at which the rates of heat evolution are greatest.

Jan 1, 1945

By Scott Turner

AS IN OTHER lines of engineering, progress in mining was influenced during 1931 by the world-wide economic depression. Low-metal prices ? resulted in active efforts to reduce production costs of base-metal mines. Probably the chief factors in reducing costs were the greater efficiency of labor, due to better relations between management and workmen, to the scarcity of jobs, reduced wages in most base-metal mines, and to lower overhead expenses secured by drastic economies. The use of mechanical equipment continued to increase, due to more efficient designs and a better practical understanding of the applicability of such equipment to requirements. With one exception, there were no startling innovations in stoping methods, but there was notable progress in the better adaptation of mining methods. In the United States, no large new base-metal or silver mines came into production during the year. At a number of mines, output was curtailed, and operations were discontinued at several important producers. On the other hand world-wide interest in gold was stimulated, as evidenced by increased output from producing mines, the reopening of some old properties, and intensive prospecting for new deposits. Mining methods at several gold mines in the United States and Canada were modified or changed to obtain a higher extraction of ore or to meet the need for additional support of the mine workings at depth. Permanent record of improvements in mining practices has been made during the year by the Federal Government; the industry thus has available for its use more detailed information than ever before. This work was done through cooperation of the mining companies and their representatives with the United States Bureau of Mines, whereby many papers descriptive of practices and costs at individual mines have been published. The Bureau's program of describing methods and costs at the more important mines (those producing in excess of $100,000 annually) is nearly completed, but papers will be issued concerning such additional mines as may possess particular interest because of novel methods, exceptional conditions or operating results, and others to supplement reports already issued. In this way, an interesting record of the results of changing conditions, or innovations in methods, will be made available.

Jan 1, 1932

By AIME

PROBABLY no greater world traveler has ever been Chairman of one of the Institute's Divisions than Henry Frederick Hebley. To begin with, he was born almost as far away as possible-in Christchurch, New Zealand, Dec. 15, 1893. There he grew up, studying mechanical engineering at the local Seddon Memorial Technical College. Then he went over to Sydney, Australia, for a bit of work before sailing for the U.S.A. in 1915. After a few months as draftsman in a San Francisco office he moved over to Clarkdale, Ariz., in the engineering department of the United Verde copper smelter, which had just gone into operation. But the war was on, and Henry thought he belonged in France with the Canadian Engineers, the United States still remaining aloof from the conflict, and that was the last the copper industry saw of him. After almost two years in France he was wounded, convalesced in England and Canada, and then went back to his native New Zealand to design concrete factory buildings. But soon the United States called again, and this time he landed in Salt Lake City with the Oregon Short Line R.R. Co. Then to Chicago in 1920. where he really got into the coal industry for good, working for the Allen K Garcia Co. on the design and operation of coal mines, beneficiation plants, and combustion equipment; and joining the Institute.

Jan 1, 1946

The income of the Institute is derived from dues, subscriptions to MINING AND METALLURGY and sale of publications. These sources are fortunately supplemented by the interest from invested funds now amounting to over $500,000, a considerable portion constituting endowments for especial purposes. Aside from the medal funds the principal endowments are the James Douglas Fund for support of the Library, the Rocky Mountain Fund and the Seeley W. Mudd Memorial Fund. The income from the two last named is available for the support of research and a variety of other purposes. It is allocated by the Board of Directors upon recommendation of standing committees in each case. An active effort is being made to increase the endowments of the Institute, it being felt that unusual opportunities exist for research and public and professional service through the organization and at a minimum of expense. J. V. W. Reynders is chairman of the Endowment Committee.

Jan 1, 1923

By C. D. Thurmond

Jan 1, 1968

By C. E. Corson

Discussion of the Paper by C. E. Corson, which was presented at the London Meeting, July, 1906. (See Bi-Monthly Bulletin, No. 11, September, pp. 725 to 742.) ALBERT SAUVEUR, Cambridge, Mass. (communication to the Secretary*) :-On close examination I think it will be found that the evidence by which Mr. Corson claims to have shown the inaccuracy of a statement I made a few years ago, is far from convincing. This statement is:- "Hot work, as such, has no influence upon the structure of the metal. Indirectly, however, by retarding crystallization until a lower temperature is reached, it may influence its structure most decidedly ; but the same results could be accomplished by heat-treatment alone, i.e., by reheating the unworked metal to the temperature from which the unworked piece was allowed to cool undisturbedly." The Metallographist, vol. ii., p. 267 (under the head of "Changes of Structure Brought About by Work"). Of the two pieces of steel tested by Mr. Corson, one was worked and finished at a " cherry red " and ' the other reheated to a cherry red, and the assumption was made that, in both cases the temperature was about 715° C., although no pyrometric device was used to record it. The possibility of considerable difference in temperature alone is so great as to invalidate Mr. Corson's inferences. The apparent temperature, moreover, is so close to the critical point of the steel as to render any conclusion very hazardous. -It is not at all evident that the annealed piece was reheated past its critical point, in which case reheating would have had practically no effect. Nor is it evident that the piece forged and finished at a cherry red was not actually below the critical point, which, by definition, I have called cold worked. Mr. Corson's explanation that " Under proper reheating, on the other hand, the steel becomes a solid solution from which crystals of approximate homogeneity and uniform size may separate" will not be readily understood.

Jan 1, 1907

By O. B. Bucklen, J. P. Matoney, P. G. Meikle, R. L. Terry

INTRODUCTION The trend in the coal industry for many years has been to make every- thing "bigger and faster." This also holds true for loading and storage facilities. Where once a 1 million st per yr (910,000 mt/yr) mine was rare, 3-5 million st per yr (2,730,000-4,550,000 mt/yr) mines are not uncommon today in the bituminous industry. This great increase in production, made possible through mechanization, requires greatly improved loading facilities just to get the coal away from the mine. Also, there is a trend to- ward combining production from more than one mine and cleaning it in a single preparation plant. In addition to increased loading capacity, this frequently necessitates raw-coal storage and blending facilities. The development of the unit train with its attendant economics has contributed more than any other factor to the widespread construction of storage and high-speed loading facilities. In the export market, the construction of ever larger coal colliers has added to the need for faster and larger loading facilities. In this climate of rapidly changing technology, any written ac-

Jan 1, 1979