Search Documents

By C. W. Phillips, R. S. Busk

WITH most cast metals the grain size may vary within wide limits, depending upon the conditions at the moment of freezing. These conditions are subject to control in magnesium-base alloys, by proper melting and superheating techniques, enabling production of quite uniform and fine-grained castings, almost independent of section thickness. However, such variations of grain size as do exist, in common with all metals, are reflected in corresponding changes in mechanical properties. It is the intent of this paper to present data giving the relationship between grain size and mechanical properties. Data are also included on the combined effects of grain size and microporosity. In addition, a short discussion of factors influencing the grain size of sand castings is included. MEASUREMENT OF GRAIN SIZE By grain size is meant the statistical distribution of volumes occupied by the individual crystallites in a metal section. Since this is almost always impossible of direct measurement, several methods of estimating and expressing the size have been evolved. Most exact methods make use of the microscope. This involves study of a single plane cut at random through the metal. What is seen in the microscope are polygons, each the cross section of a grain. The diameters or areas of these polygons are then measured and the grain size is expressed as an average diameter, number of grains per unit area, average area per grain, or, rarely, average volume per grain. Rutherford, Aborn, and Bain3 have discussed extensively the errors involved when using a plane section to estimate volume. They clearly point out that the tendency is to underestimate the true grain size because of the nature of the measurement. The A.S.T.M.. recommends that measurement be made by comparison with a standard chart, by means of Jeffries' planimetric method' or Heyn's intercept method. The Society recommends that the notation be in terms of the number of grains per unit area (as is the grain-size number used for steel) or as an average diameter, expressed in inches or millimeters (as for copper and brass). The method of measurement used for this study was comparison with a standard chart, which has been described by P. F. George.', The chart was constructed by photographing at i00 diameters a uniform specimen with an average grain diameter of 0.003 in. The average diameter of this specimen was determined by numerous measurements, using both the Jeffries and Heyn methods. The other grain sizes were then obtained by appropriate enlargement of the master sample. Careful comparison of the chart method with other methods on identical samples indicates that though the differences be-

Jan 1, 1945

By L. A. Creglow

IN common with many other companies engaged in the mining and processing of ores, research has always been an important activity of the United States Smelting Refining and Mining Company. Much of this research has been carried on at the various plants of the Company by the operating staffs, and over the years has been an essential factor in developing new methods and improving existing methods of operation. In 1917 arrangements were made with the Massachusetts Institute of Technology under which the Company had the exclusive use of one or two small laboratories in the then newly constructed MIT buildings and the use of the metallurgical laboratories, subject of course to the Institute's needs. After about two years this work was temporarily discontinued but was resumed in 1920 under the direction of G. H. Clevenger, consulting metallurgist for the Company, who recently retired. Becoming cramped for space, the laboratory was moved to a location near MIT on Amherst Street, Cambridge, in 1924. Establishment of a general research laboratory in metropolitan Boston naturally followed from the fact that the head office of the Company was located there and that the library facilities available for all types of research were, and are, unsurpassed. The disadvantages in carrying on research at great distances from the operating units of the Company were always apparent, but with widely scattered plants this disadvantage could not he overcome. With

Jan 1, 1948

By Henry Rawdon

Cold-working is generally considered as a process of hardening metals. Diamet-rically opposite statements concerning the applicability of the scratch-hardness method in the testing of cold-worked metals, particularly after severe deformation, which exist in the technical literature led to the study of the results which are summarized in this paper. A series of metals, of which copper, iron and tin are used as illustrations here, were cold rolled to a definite degree without any intermediate annealing and the hardness determined by both the scratch and Brinell methods. The results indicate that the metal hardens rapidly during the initial stages of deformation; however, after a certain stage, which corresponds to a rather definite microstructure, the metal becomes softer and in its final form may be softer than the metal in its initial stage. As part of the study of the scratch-hardness method for metals and alloys in cooperation with one of the technical committees of the American Society for Testing Materials, the authors devoted considerable time to the study of the changes in hardness of metals when cold rolled. Various seemingly contradictory statements in the technical literature concerning the applicability of the scratch-hardness method to such cold-rolled materials were among the principal reasons for the investigation, the results of which are in part presented here. The effect of cold deformation, at least in moderate degrees, on the hardness as measured by the Brinell and other common methods is so well known that further reference is unnecessary. Concerning the scratch hardness of cold-worked metals, Martens and Heyn state' that hardness, whether measured by the ball-pressure method (Kugeldruck) or by the scratch method (Ritzverfahren), will be increased by cold deformation. Jeffries and Archer give a seemingly diametrically opposite view. They state,2 that "the sclerometer (indicating scratch

Jan 1, 1924

By M. Marciano, K. Kreider

Silicon carbide coated boron fiber (Borsic) reinforced aluminum composites were made which exhibit strength and modulus values predicted by the rule of mixtures. A successful technique for fabricating these composites consists of plasma spraying of monolayer filament reinforced tapes and subsequent diffusion bonding of these tapes into composites. The elastic properties of the composites were given by the rule of mixtures in reinforced directions. (The modulus parallel to the fibers was 32 x 106 psi for a composite with 50 pct by volume fibers. The other elastic properties for a composite with 50 pct fiber were transverse modulus = 14 to 16 X 10 psi, G = 9.5 x 106psi, and v,, = 0.23. Tensile strengths of over 190,000 psi were measured for the composites with 50 pct fiber and the average strength for these composites was 162,000 psi. These same composites had interlaminar shear strengths of 12 to 15,000 psi. Multidirectionally reinforced composites demonstrated the same reinforcement efficiency in strength and modulus as the uni-directimlly reinforced composites. Comrpessive strengths of composites with 50 pct by volume fiber were found to be greater than 250,000 psi. STRUCTURAL filamentary composite materials are being considered for use where high strength, high modulus, and lightweight materials are required. Metal matrix composites have been considered for use at temperatures ranging from cryogenic (aluminum stainless steel) to 6000°F (plasma sprayed tungsten plus tungsten fiber) and other requirements have been similarly diverse. Metal matrix composites offer high modulus and high strength in unreinforced directions, the ability to be joined by brazing or welding, and greater fracture toughness compared with the more easily fabricated resin matrix composites. This paper deals with the mechanical properties of aluminum boron composites, a system which is being considered for applications where lightweight, high modulus, and high strength are required at temperatures including those above the normal operating temperatures of resin composites. The boron fiber used in this investigation had an average room temperature strength of greater than 400,000 psi, a modulus of 58 x 106 psi, and a density of 0.09 lb per cu in. (2.6 g per cu cm).' The fiber used in the composites had a coating of silicon carbide to retard degrading reactions with the matrix at elevated temperatures. The coated fiber, which is sold commercially as Borsic: has been reported to have excellent resistance to degradation at temperatures up to 600°C in air and in aluminum2 and the same mechanical properties as the standard bare boron fiber. Fabrication of Composites. The composites were diffusion bonded from plasma sprayed monolayer tapes. These tapes were fabricated on a substrate of aluminum alloy foil which is incorporated in the composite matrix. The technique consists of winding a layer of fiber on the foil, and plasma spraying the balance of the matrix alloy over the windings which bonds all of the components together. Advantages of this process include the ability to achieve good fiber spacing, Fig. 1, the formation of a good bond between fiber and matrix (achieved during the plasma spraying), and the adaptability of the process for forming large and complex parts. This is particularly true when used with brazing foil backing which alloys low pressure bonding of the structural shape. PROPERTY EVALUATION TECHNIQUES Tensile test specimens, 5 to 7 in. long with a reduced gage section and ,030 to ,040 in. thick, were cut from composite sheets with a diamond saw. The gage section was .200 in. wide, while the gripped section was .240 in. wide and over 2 in. long in each grip. The standard gage length used was 1 in., however, transverse specimens (i.e., specimens with the fibers oriented 90 deg to the loading axis) were tested without a reduced section. Twelve specimens were also made with a 3-in. gage length but no significant effect of gage length was measured. The tensile test specimens were mounted in a fixture and aligned in friction grips using a 10X microscope. Unbonded foil doublers (0.010-in.-thick aluminum) were used to insure firm gripping with a minimum of damage to the fibers. The test specimens were transferred to the testing machine in a rigid fixture and mounted in the self aligning loading train. Testing was performed using a Tinius Olsen four screw testing machine with a torsion bar LVDT load

Jan 1, 1970

By H. C. Miller

THE gas-lift method of flowing oil from wells is the outstanding feature of petroleum technology today. Its forerunner, the air lift, was used successfully first, in the Baku fields of Russia, in 1899, and later in the Gulf Coast fields of Texas and Louisiana and the Kern River field of California. It is still used to a limited extent in certain oil fields. The use of compressed natural gas for lifting oil from wells has supplanted the air-lift method in a measure in those fields where a sufficient quantity of gas accompanies the oil to make the gas lift possible, or where natural gas is plentiful and inexpensive. We find therefore in California, that, natural gas is used at practically every well where a gaseous medium is employed to flow the oil. The use of natural gas has many advantages over that of air. It is possible to recover and save the gasoline from the gas that accompanied the oil to the surface. This gasoline would be wasted if air were used as the lifting medium. Also, certain proportions of air and gas form an explosive mixture that cannot be handled safely by compressors. Another advantage that gas has over air is that gas under pressure is more soluble in oil. Gas in solution in oil reduces the viscosity of the oil that is being produced and causes it to flow more readily through the. tubing and flow lines. The gas lift has made it possible to recover many thousands of barrels of oil from deep wells in California that could not have been produced otherwise. It would not have been economical, had it been mechanically possible to produce such wells as the world's deepest producing oil well (Miley Athen's No. 6, Rosecranz field, California) by any other method of pumping known today. At this well, production is obtained from between 7305 and 7591 ft. and 11 months after completion of the well, production was being maintained on the gas lift it approximately 2000 bbl. a month. The crookedness of the hole, or its diameter and depth will not prevent the successful application of gas-lift pumping when other conditions are favorable.

Jan 1, 1927

By Charles Brush

THE general subject of accurate pyrometry, its great development in recent years, and the importance of its application in arts and manufactures is so ably treated in other papers that this paper will bee confined to a resume of some research work on certain temperature effects in carbon and other steels, some of which appear to, be new. The results of these researches are embodied in several papers presented to' various scientific societies during the last few years, most of them under the general title of Spontaneous Generation of Heat in Recently Hardened Steel.1 Several years ago, when studying the behavior, tinder certain conditions, of specimens of hardened tool steel, I observed that they all spontaneously generated a small quantity of heat, the rate of generation diminishing from day to day for several weeks before generation became imperceptible in the sensitive calorimeter used. In each case the steel had been hardened only a few days prior to its use. It seemed highly probable that the generation of heat was associated with some sort of "seasoning" or incipient annealing process, perhaps accompanied by slight changes of volume, and that it would be most rapid immediately after hardening. I subsequently investigated this curious phenomenon more fully. Twelve ½ in. round bars of tool steel, 5 in. long and with machined surfaces, were hardened by heating to high cherry red in a reducing atmosphere of a gas furnace and quenched in cold water. The bars then had a thin strongly adhering coating of black oxide. They were next stirred in a large quantity of water at room temperature, to acquire that temperature, wiped dry, and oiled with heavy, neutral mineral oil to prevent generation of heat by further surface oxidation, wiped free of excess of oil and placed in the copper cylinder of a heat-insulated box.

Jan 9, 1919

By R. J. Keene

The South Works high-tonnage billet caster was started in late March 1971, with the first heat being successfully cast to completion. Currently, over 31,500 tons per month are being produced. U. S. Steel designed and built this caster with the objective of producing quality-steel billets for critical bar, rod, and wire applications. The essential design parameters were based on studies conducted on the Research Laboratory's pilot caster, also located at South works. 1,2,3)* The caster is a four-strand, straight-mold machine that produces 7.5-inch- square billets at rates exceeding 300 tons per hour. An in-line-reduction mill reduces each strand to either 6-inch-, 5-inch-, or 4-inch-square billets.

Jan 1, 1972

By S. E. Bronisz, Dana L. Douglass

a Uranium was deformed by cold rolling, and the effects of this plustic deformation on the microstruc-ture of the metal were observed by the technique of transmission elecbon microscopy. The recrystalli-zation of selected cold-wmked samples was also studied by this method. The samples were prepared for examination by electrolytic thinning in a standard metallographic electrolyte which has not been previously reported as being used in producing thin foils of uranium. The microstructural changes observed in the a uranium were generally similar to those seen by optical microscopy. The changes in the microstructure of a uranium following cold work and recrystallization treatments have been the subjects of several studies employing optical and X-ray techniques.12-19 These studies indicated that twinning was the redominant mode of deformation at room temperature20 and that the regions of high energy associated with the deformation twins were preferred sites for the initiation of recrystallization.15,18, Recently several workers have prepared thin foils of uranium suitable for examination by transmission electron microscopy.'-lo The foils thus prepared have been used to study fission fragment damage; a particular dislocation reaction,' and gas precipitation." At this laboratory the microstructural changes occurring during the cold working and recrystallizing of a uranium samples have been studied by using transmission electron-microscopy techniques. The foils used in this work were electrolytically thinned in a polishing bath not reported previously in the literature as being used for this purpose. EXPERIMENTAL PROCEDURE The uranium used in this investigation was depleted a uranium sheet 4 mils thick. The results of a spectrochemical analysis of this material are shown in Table I. The as-received uranium was cut into strips, 1 in. wide by 5 in. long, and annealed in vacuo at 600°C for 2-1/2 hr. The resulting microstructure consisted of relatively uniform, equiaxed grains having diameters of 10 to 50 p. Cold Working. The cold-worked samples were prepared by rolling several of the annealed uranium strips to various thicknesses. The strips were reduced 3.5 ± 0.5, 6.0 ± 0.6, 10.0 ± 0.5, 19.5 ± 1.0, and 28.5 ± 2.0 pct in thickness. It was not possible to achieve these reductions with a single pass through the rolling mill, so the strips were turned end for end during the rolling procedure. The cold-rolled strips were stored in dry ice until samples from them could be thinned and examined (within 24 hr after rolling). Annealing. The samples used in studying the re-crystallization behavior of a uranium were obtained by annealing sections of the strips which had been reduced 10.0 and 28.5 pct. These samples were sealed in evacuated Pyrex capsules and were annealed in a tube furnace at temperatures from 200" to 600°C and for times from 1/2 to 2 hr, see Table l. Thinning: The samples from the rolling and heat treatments were prepared for examination in the electron microscope by electropolishing in a bath composed of 25 g chromic acid, 133 ml glacial acetic acid, and 25 ml water. This electrolyte has been used and recommended for preparing specimens for optical metallography It was necessary to mask the edges of the sample with a stop-off paint in order to prevent preferential attack in these areas. The paint used was made by dissolving polystyrene in benzene. The electrolytic cell consisted of a cylindrical stainless-steel cathode placed in a beaker containing the electrolyte, with the sample as the anode positioned at the cell axis. The temperature of the electrolyte was held below 15°C by cooling with liquid

Jan 1, 1963

By D. Geoffry Minnes

Nepheline syenite is a silica deficient crystalline rock consisting of albite and microcline feldspars and nepheline, together with varying but small amounts of mafic silicates and other accessory minerals. Nepheline-bearing rocks are widely distributed around the world but only in Canada, Norway, the Union of Soviet Socialist Republics, and the United States are deposits worked commercially. Because of its low melting point and fluxing ability, nepheline syenite was investigated in the early 1900s by many students of glass and ceramics. Although the nepheline syenite deposits in Methuen Township, Ont., Canada, were discovered as early as 1897 it wasn't until 1935 that the first mill was erected to produce nepheline syenite products. In Canada, nepheline syenite deposits are worked by Indusmin Ltd. and International Minerals and Chemical Corp. (Canada) Ltd. who have combined production capacity in excess of 1800 tpd. Between 1935 and 1972 seven million tons valued at $78 million were produced from the Methuen Township deposits. In Norway, the Norsk Nefelin Div. of Elkem Spigerverket has produced nepheline syenite from a deposit on Stjernoy Island in western Finnmark since early 1960. Between 1961 and 1972 the company produced 930,000 mt with an estimated value of $17 million. Nepheline syenite has been under investigation in the Union of Soviet Socialist Republics (USSR) since at least 1928. In 1951 the first commercial alumina works was brought on stream at Volkhov, near Leningrad, utilizing nepheline concentrates from the Kola peninsula as mill feed. Since then two others have been completed and more are planned. Large quantities of portland cement, sodium carbonate, and potassium carbonate are produced in conjunction with the alumina. In the United States, nepheline syenite has been produced for many years from deposits in central Arkansas by the Big Rock Stone and Materials Co. for construction aggregates and, since 1947, for roofing granules by the 3M Co. Chap. 16 on "Feldspar, Nepheline Syenite, and Aplite" in the 3rd ed. of Industrial Minerals and Rocks (Castle, and Gillson, 1960) and Nepheline Syenite Deposits of Southern Ontario (Hewitt, 1960) contain excellent accounts of earlier commercial development of nepheline syenite as a glass and ceramic material. Therefore this chapter deals mostly with the period since 1960 and with matters not previously reported in detail. An English monograph on Nepheline-Syenite and Phonolite (Allen et al., 1968) is a complete current survey of nepheline syenite which, with its very complete list of references. is an excellent source book. End Uses Nepheline syenite from the Canadian and Norwegian producers finds use primarily in the manufacture of glass and ceramics. One producer also makes several grades of nepheline syenite that are useful as extender pigments and fillers in paint, plastics, and rubber. In the Soviet Union nepheline is used in increasing quantities in the manufacture of alumina, alkali carbonates, and portland cement and to a lesser degree it is used in the manufacture of colored container glass.

Jan 1, 1975

JOHN W. BELL, *Montreal, Quebec, Canada (communication to the Secretary?). The test results in Mr. Taggart's paper will, I am sure, be recognized as a notable contribution, and of great assistance in the study of the performance of the Hardinge mill. I regret, however, being obliged to note that Mr. Taggart still retains. such confidence in the Kick-Stadler method of computing the ?relative mechanical efficiency" of crushing machines. The Rittinger-Kick graph submitted by Mr. Gates and the tests made at McGill University disclosed precisely the same fundamental defect in the Kick-Stadler theory. Consequently, I have been obliged to recalculate in terms of Rittinger surface units the results obtained in the 28 rock-crushing tests cited by Mr. Taggart, in order to find- out what the relative efficiencies really were. In order to show the large discrepancies between the Stadler and Rittinger R. M. R's, the most, efficient result disclosed by each method is represented by the number 100, and the R.. M. E.'s for the other tests have been recalculated on this basis. The results will be found in Table 1. Personally, I look forward to the time when we shall cease to talk about "relative mechanical efficiency" and merely refer to the "efficiency" of a crusher. All that is required to accomplish this is to agree on a standard method for determining the "crushing constant" of a given rock and a standard method for calculating the efficiency. The figures in the fourth column of Table 1 have been derived by assuming a constant of 2,000 for the quartzite crushed in the Yale tests. The Stadler method sometimes indicates changes in efficiency produced by, changes in operating conditions, as I pointed out in a paper describing rock-crushing tests made at McGill University. It is, however, not enough to determine that certain changes increase or decrease efficiency; surely it is equally important to determine the magnitude of these variations. By examination of Mr. Taggart's results, I have been obliged to conclude that the size of feed and amount of reduction greatly influence the Stadler R. M. E. figures, that they are positively misleading. It should be mentioned that since the majority of the tests have been made at the least efficient feed rates, and since, moreover, it is one of the evidently very important factors affecting efficiency, it is possible that different results might be obtained by a high-tonnage feed series, and that

Jan 8, 1917

By Francis H. Crockard

DURING the past five years we have probably witnessed greater technological advances than in any similar period. Industry and science have steadily marched ahead. The makers of iron and steel products have watched with great interest the development of stream-lined trains, faster and safer airplanes, the entirely new science of air-conditioning and the widespread use of stainless steels. Since 1930, we have witnessed the erection of the world's largest suspension bridge, the largest and fastest ocean liner and the spectacular Boulder Dam, while even greater things are planned in these particular fields. Other industries, too, have been moving ahead rapidly. This advance in a few years has been caused primarily by the fierce competition of the depression. Now, more than ever, is the emphasis placed upon quality and service. Makers of southern merchant pig iron have been no exception and have been confronted with increasingly strict chemical specifications and with much greater stress on physical characteristics than ever before. For example, sulfur in the iron must be held very low, competition demanding that it be in the 0.020's and low 0.030's; silicon content must be held within a very narrow range, and definite requirements of phosphorus and manganese are an essential part of the specifications. Physical characteristics are becoming of increasingly greater importance. The introduction of triple-skimmed, slow-cooled iron several years ago was the first step in this direction. Now there are a few customers who buy iron by chemical analysis and physical appearance, having found that the analysis alone is an insufficient guide to their requirements.

Jan 1, 1935

By R. F. Mehl, J. T. Ransom

For many years the Metals Research Laboratory of Carnegie Institute of Technology has been concerned with the statistical nature of the engineering properties of steel from an experimental viewpoint, particularly those properties representing ductility.' In the past three years new work has been directed toward evaluating the statistical nature of the endurance properties. It has been shown that both the fracture curve and the endurance limit in fatigue are markedly statistical in nature. The S-N curve (and the endurance limit) of ferrous materials is often determined with specimens which number as few as ten. The common procedure is to test the first specimen at a stress well above the expected endurance hmit. Each succeeding specimen is then tested at a progressively lower stress, until, after five or six tests, a specimen runs ten million or so cycles without failing. Two or three more specimens are then used to find the highest stress at which failure will not occur; the limiting stress determined in this way is called the endurance limit. It has now been found, however, that the variability in the fracture curve and in the endurance limit in heat-treated alloy forging steels is so great that S-N curves must be drawn on the basis of distribution curves which can be appraised only by statistical methods. Two methods have been adopted in this study: (1) straightforward statistical studies of cycles to fracture of a number of specimens at each of a series of stress levels, and (2) a new abbreviated statistical method, known as "staircase testing."2 The latter corisists in testing a series of specimens, one by one, with the test stress for any given specimen automatically

Jan 1, 1950

By J. D. Kalasky

Continuous mining has revolutionized the coal industry but intensified the problems of earlier mechanization. From the installation of the first miner, it was recognized that face ventilation would be one of these problems. To establish an efficient work cycle for the equipment being used, conventional mechanized mining provides four or more development faces. Continuous mining, relying on a single machine, requires only one face, although more than one can be driven alternately by the same machine. In gaseous areas mined by the older methods, the intermittent rate of exposure allows time for the face to bleed off or be cleared, and the width obtained with conventional units makes it possible to hang a brattice line almost to the face. Continuous mining increases the ventilation hazards; there is no margin of time, and very limited space. For all practical purposes, continuous miners available today can be grouped into two major types, rippers and borers. The two can be further classified, respectively, as flexible and rigid. Both types have been in operation in U. S. coal mines for the past five to ten years in a number of seams, under various conditions ranging from slightly gaseous to very gaseous. Common methods of face ventilation utilizing jute or plastic brattice material for line curtains, stoppings, and checks have so far met with success. Air volumes to operating sections are greater than for conventional mining, and specific instructions have been given to section crews stressing the precautions needed in dealing with a steady rate of gas emission and the importance of maintaining reasonably air-tight brattice to direct a good steady flow toward the face at all times. Operators of continuous miners, as well as the foreman on each section, are equipped with an approved safety lamp for gas testing. When the miner is in steady operation, tests for gas at the face are made at 15 to 30-min intervals, depending on the

Jan 1, 1960

By H. C. Miller

The gas-lift method of flowing oil from wells is the outstanding feature of petroleum technology today. Its forerunner, the air-lift, was used successfully first, in the Baku fields of Russia, in 1899, and later in the Gulf Coast fields of Texas and Louisiana and the Kern River field of California. It is still used to a limited extent in certain oil fields. The use of compressed natural gas for lifting oil from wells has supplanted the air-lift method in a measure in those fields where a sufficient quantity of gas accompanies the oil to make the gas-lift possible, or where natural gas is plentiful and inexpensive. We find, therefore, in California, that natural gas is used at practically every well where a gaseous medium is employed to flow the oil. The use of natural gas has many advantages over that of air. It is possible to recover and save the gasoline from the gas that accompanies the oil to the surface. This gasoline would be wasted if air were used as the lifting medium. Also, certain proportions of air and gas form an explosive mixture that cannot be handled safely by compressors. Another advantage that gas has over air is that gas under pressure is more soluble in oil. Gas in solution in oil reduces the viscosity of the oil that is being produced and causes it to flow more readily through the tubing and flow lines. The gas-lift has made it possible to recover many thousands of barrels of oil from deep wells in California that could not have been produced otherwise. It would not have been economical, had it been mechanically possible, to produce such wells as the world's deepest producing oil well (Miley Athen's No. 6, Rosecrans field, California) by any other method of pumping known today. At this well, production is obtained from between 7305 and 7591 ft. and 11 months after completion of the well, production was being maintained on the gas-lift at approximately 2000 bbl. a month. The crookedness of the hole, or its diameter and depth will not prevent the successful application of gas-lift pumping when other conditions are favorable.

Jan 1, 1928

By M. E. Wadsworth, T. L. MacKay

Sintered UO, samples were leached in sulfuric acid solutions of various concentrations. A pressurized system was used so that it was possible to investigate the kinetics of the reaction to 270°C with oxygen overpressures as high as 900 psi. The rate was observed to be a function of the concentration of hydrogen ions and directly proportional to the partial pressure of oxygen. Evidences are presented which indicate that a UO2 surface site reacts with a molecule of water to form a hydroxyl complex which in turn can dissociate with the characteristics of a weak acid. A rate determining step has been proposed which involves the reaction between an oxygen molecule and the hydroxyl complex on the surface of UO,. ThE 2 principal methods for uranium dissolution are carbonate and acid leaching. The sulfuric acid leach is the more popular and is used for the treatment of the majority of the ores of Africa, Canada, and the United States. Low recoveries in basic leach circuits led investigators at the University of British columbia1 to study leaching of uranium ores in pressurized vessels. Early in the study of dissolution of uranium it was found that only uranium in the hexava-lent state could be leached in acid or basic circuits. Therefore, the use of oxygen over-pressure in an autoclave offered an interesting approach to solving the low recovery problems of carbonate leaching. UO, was used in this study because it could be obtained in high purity and also because it is representative of the most refractory of the primary uranium minerals. A pressurized system was used to provide a means whereby important temperature and pressure parameters could be varied for the evaluation of the kinetic processes. The mechanism for the dissolution of UO2 should be similar for any of the uraninite type minerals. At the present all of the kinetic studies that have been conducted have been in carbonate media. Peters and Halpern2 carried out a kinetic study of the leaching of pitchblende. Their specimens were pitchblende ores selected on the basis of high grade and homogeneity. Pearson and wadsworth3 conducted a kinetic study of the dissolution of UO2 in carbonate solutions with results very similar to those obtained by Peters and Halpern. EXPERIMENTAL The UO2 as received* was found by spectroscopic *Mallinckrodt reagent, supplied by the Atomic Energy Commission. analysis to have a purity of 99.94 pct 0.03. It was ground in a mechanical agate mortar and screened through a 400-mesh sieve. Thin flat disks of UO2 were prepared by pressing the sized powder in a specially constructed die at a total pressure of approximately 25 tons per sq in. The pressed disks were approximately 0.25 cm thick, 1.6 cm diam, and 3.5 g in weight. As pressed, the samples were approximately 65 pct of theoretical density. It was essential that a binder such as poly-vinyl alcohol be added before pressing to prevent formation of cracks when fired. It was found by trial and error that pressed disks sintered close to 1870°C in a hydrogen atmosphere, reach densities between 91 and 91.5 pct of the theoretical density. At this density the samples had no measurable porosity based upon a 2-hr emersion in boiling water. An X-ray examination of these sintered UO2 disks showed them to be identical with the original UO2 received. Reaction of UO2 with the alundum furnace core was prevented by placing molybdenum between the samples and the core according to the method of Corwin and Eyerly.4 Leaching studies were carried out in a specially designed autoclave, the details of which have been presented e1sewhere.6 The main features of the equipment as applied to a kinetic study are: 1) solution samples may be removed during the course of a single run; and 2) temperature and agitation are carefully controlled. Two-ml samples removed from the autoclave during the course of a run were analyzed for U3O8 content with a Beckman model DK-2 spectrophotometer by the method of

Jan 1, 1959

By C. F. Nagel

THIS paper is written primarily for those who are familiar with the processes mentioned but who desire a further insight into some of the fundamental principles. It does not give a complete description of the various practices employed in the working of aluminum and its alloys, but presents a few illustrations of the essential respects in which aluminum differs from other common metals, and emphasizes the controlling factors of the processes under consideration. HEAT TREATING Certain aluminum alloys are capable of having their mechanical properties greatly altered by a heat-treatment process. The degree of this improvement may be illustrated by some typical properties of duralumin (Table 1). It is essential that the material be in the wrought condition in order to obtain maximum heat-treatment effects. [ ] In the case of duralumin, the process consists of heating the metal to a prescribed temperature and then quenching it. Immediately after quenching, the material is relatively soft though not as soft as in the annealed state. If allowed to stand at room temperature, the material changes, increasing in hardness and strength without loss of elongation, but at the expense of the plasticity. This action is very rapid at first, gradually diminishing in intensity and to all practical purposes being completed in about four days. This process of hardening is termed

Jan 1, 1928

By C. F. Nagel

This paper is written primarily for those who are familiar with the processes mentioned but who desire a further insight into some of the fundamental principles. It does not give a complete description of the various practices employed in the working of aluminum and its alloys, but presents a few illustrations of the essential respects in which aluminum differs from other common metals, and emphasizes the controlling factors of the processes under consideration. Heat Treating Certain aluminum alloys are capable of having their mechanical properties greatly altered by a heat-treatment process. The degree of this irnprovement may be illustrated by some typical properties of dura-lurnin (Table 1). It is essential that the material be in the wrought condition in order to obtain rnaximum heat-treatment effects. In the case of duralumin, the process consists of heating the metal to a prescribed temperature and then quenching it. Immediately after quenching, the material is relatively soft though not as soft as in the annealed state. If allowed to stand at room temperature, the material changes, increasing in hardness and strength without loss of elongation, but at the expense of the plasticity. This action is very rapid at first, gradually diminishing in intensity and to all practical purposes being completed in about four days. This process of hardening is termed

By R. S. Sandhu, L. E. Baker, W. Y. Shieh

The finite element method of analysis was introduced by Clough.1 Within a short period, it has developed into a powerful solution technique in structural and continuum mechanics. It has been used to solve boundary value problems in two and three-dimensional elasticity.2-5 Anisotropy and heterogeneity of materials were allowed for at the earliest stages. 1,4 Its application has been extended to allow for cracks,5 creep and viscoelasticity, 6,7 incremental construction,6-8 nonlinear elasticity3,9 effect of joints in rock,10 and to materials with different behavior in tension and compression.7 Because of its versatility, the finite element method has found increasing application in the field of rock mechanics. In fact, several of the more significant developments have been motivated by problems in this field. Elasto-plastic material behavior based on the incremental or rate-type theory of plasticity rather than the deformation theory was considered by Reyes and Deere11 A material law based on a generalization 12 of the Mohr-Coulomb criterion was used. In this chapter, the formulation of material laws developed by Reyes and Deere 11 is used. An efficient analysis procedure, incorporating recent developments in finite element analysis, is developed for plane-strain conditions. To demonstrate its effectiveness, the procedure is applied to three cases, one for which an exact solution is available, another for which field observations had been made, and a third one for which a parallel study was made, using an accepted limit-equilibrium method.

Jan 1, 1970

By Robert A. Stansbury

Keeping development ahead of retreat mining is a problem which occurs nearly everywhere longwall mining is used in the United States. As improved equipment technology has allowed the application of longwall mining to more difficult mining conditions, and with higher retreat rates, the problem has become more critical. Many factors determine development speed, including roof and floor conditions, mining heights, seam heights, and the number of entries. In an effort to maximize the rate of development and production from development sections, U. S. Steel's Gary District has used five entry, three entry, four entry and is planning two entry development panels at its different mines. With the introduction of various types of shield supports, it is now possible to utilize longwall mining in higher coal over 3 meters (10 feet), lower coal under one meter, in difficult roof conditions, and with soft floor. Improved shearers of 300 KW (400 HP) and more make cutting heights over 3 meters (10 feet) possible, and off pan shearers and improved Gleithobel plows make cutting less than 1 meter (40 inches) seam height possible. Longwall mining under these conditions puts an added strain on the ability to develop panels as fast as they are retreated. Poor roof conditions require a substantial amount of additional roof support to ensure that roof control in the head and tall entries will not hinder longwall retreat. The additional measures of longer bolts, resin bolts, point anchor resin bolts, roof mats, roof trusses, steel or wood cross bars, and roof grouting all place an additional burden on man power, installation time, and cost on the mining cycle. Additional roof bolting on development can cut the potential mining rate in half, and any roof falls cause significant delays to mining. Timbers and cribs can restrict ventilation and require more entries. Soft floor conditions can greatly impede development through tramming difficulties with shuttle cars and roof bolters, time required for cleaning and repairing roadways, and maintenance difficulties on equipment. High coal sometimes requires rib support to be Installed during the mining cycle, further cutting the mining rate. Mining low seams requires that roof or floor be mined in the head and tail entries as well as the track or tractor roadway entry to provide clearance of the longwall equipment. Mining this rock slows down the mining rate because of the extra material being mined and the extra wear and tear on equipment. To a large degree these conditions effecting development speed cannot be controlled.

Jan 1, 1981

By Bradley Stoughton

The regular, bottom-blown Bessemer converter of the present day is a modification of previous forms, and most of the latest proposed modifications of it are merely returns to former types which Ressemer discarded. That he tried almost every conceivable method of blowing iron, with tuyeres at almost every possible position or angle, is well known; and it is to be supposed that he was familiar with the advantages of each type, since he finally settled on that form which has not been improved upon hitherto, for the purposes for which converters will generally be used. Modifications have been tried along two lines: In the arrangement of tuyeres, and in the manner of carrying out the process with tuyeres still blowing vertically upward through the bath. While they have all failed in general competition with the regular modern type of vessel, some of them have found special fields in which they have held their own. The most notable example is in the steel-casting industry, and especially in that part of it concerned with the manufacture of castings which require very hot or very fluid metal, or supply a demand of constantly varying physical or chemical requirements. In this industry the small converters occupy a field between that of the crucible-process and that of the open-hearth process, arid have won a place for themselves in France, England, America, Russia and other countries, which they bid fair to retain until either a new method is discovered of producing cheaply very hot, fluid steel, or the open-hearth process is so improved that very hot steel may be made with it at lower cost of repairs to lining arid roof.

Jan 1, 1903