Search Documents

By Enid C. Plante

INTRODUCTION To extend our knowledge of the flotation behavior of sulphide minerals, the response of the following minerals to ethyl xanthate as collector was studied by captive bubble and cylinder flotation tests: antimonite (Sb2S3), arsenopyrite (FeAsS), covellite (CuS), marcasite (FeS2), orpiment (As2S3), pyrrhotite (FeS) and tetrahedrite (4CU2S, Sb2S3). Lollingite (FeAs2) was also examined to determine if its behavior could be correlated with that of pyrite or marcasite (FeS2). EXPERIMENTAL METHOD Mineral for Flotation and Contact Tests Mineral was prepared in the manner already described' and its behavior both freshly ground and "oxidized" was studied. Tests in which the mineral was allowed to oxidize for various periods showed that a uniform response to xanthate was reached in two days or less. Oxidation Products The soluble oxidation products from most of the above minerals were measured and their effect on the flotation of the mineral studied. The mineral samples were wet ground to minus-52 mesh and deslimed, and 20 g of this material placed in 200 ml of distilled water of a measured pH value, and C02 free air bubbled through each suspension at a constant rate (about 1 bubble/sec) for 5 days. It has been shown1 that the size of the mineral is unimportant in the rate of formation of oxidation products and that probably the supply of oxygen to the mineral is the rate-determining step. At the end of 5 days the pH value of the supernatant liquid was measured again, the mineral filtered off and the soluble products determined. Methods for estimation of sulphur acids, ferrous and ferric iron and copper have already been described.1 No satisfactory method was found for antimony. Arsenic was estimated as the arsenate.2 FLOTATION OF "UNOXIDIZED" MINERALS WITH ETHYL XANTHATE AS COLLECTOR Fig I to 3, 4, 6, show the effect of alkali and cyanide as depressants for the minerals with 25 mg potassium ethyl xanthate per liter as collector at 35°C. Wark and Cox3 have shown that with ethyl xanthate as collector, galena, pyrite and chalcopyrite show a greater tolerance to cyanide and hydroxyl ions at room temperature than at 35°C. Covellite (Fig I), marcasite (Fig 2) and pyrrhotite (Fig 3) behave similarly. The independence of the curves for pyrrhotite at 35°C with respect to cyanide

Jan 1, 1947

By Fred N. Kissell, Natesa I. Jayaraman

Introduction This paper describes a recent Bureau of Mines research project that resulted in a simple procedure for reducing the dust exposure of longwall shearer operators. This project involved the development and testing of a water spray and passive shield system to hold dust against the face and away from the shearer operators. This system is known as the Shearer- Clearer.

Jan 1, 1981

By John S. Johnson

THE purpose of this article is to describe several types of borehole lining in common use, and especially to offer a relatively new means of reducing the expense of maintaining boreholes where they are subjected to corrosive action of water flowing either inside or outside of their casing. In the Anthracite region of Pennsylvania, boreholes are used for many purposes, the principal ones being: openings between the surface and underground workings through which are passed steam, water and compressed-air lines, ropeways from surface hoists to underground rope haulages, conduits for electric power and signal lines, water-discharge lines from underground pumping stations, and inlets to mine workings for flushing material. LININGS FOR BOREHOLES The inadequacy of steel pipe for use in boreholes has long been recognized. Various substitute materials have been tried, including screw-joint cast-iron pipe (Fig. I). Cast-iron pipe, while very effective as a discharge line for acid water (mine water) being pumped to the surface, is not so effective when serving as a conduit for silt and crushed rock being flushed underground for filling mine voids. Terra cotta pipe (Fig. 2) has been used in boreholes, and lasts a long time if the glazed inner surface of the pipe remains intact. Its installation in a borehole is very difficult and is recommended only where it is certain that there will be no subsidence of the surrounding territory. Accessibility in order properly to join each section of the pipe is essential to a satisfactory job. In large water holes, where it is possible to lower a man into the hole for sealing the joints of the pipe, glazed terra cotta pipe has been used successfully for delivering mine water from pumps in the mines. For large holes used for flushing refuse into mine workings where the surface wash is shallow, standard paving brick have been used to form a tube through the wash to the bedrock. These brick are laid radially, backed by common brick and cobbles laid in cement. It is obvious that the shaft through the wash must be large enough to permit a man to work in it. The flushing material is carried through bare rock from the juncture at bedrock to the openings underground. This plan has been used, particularly where a cast-iron surface line is laid upon the surface to carry the flushing material from the breaker to the hole, and down the hole continuously, with no opening to the air at the top of the hole, thereby eliminating the necessity of an attendant at this point (Fig. 3). Another similar type of borehole lining is constructed of hexagonal pieces of vitrified brick (Fig. 4). This type requires a steel drive pipe through the surface wash large enough to provide a finished tube of the desired size surrounded by a brick wall about 4 in. thick. The special bricks are laid in cement, six to a circle, around a lubricated pipe used as a form, and lowered in sections inside the large drive pipe; the bottom section is seated in a socket drilled in the solid rock, having the same inside

Jan 1, 1941

By J. L. Gregg

A STUDY of copper and silver base alloys was made with the object of finding, if possible, useful alloys subject to dispersion hardening. These studies led to the discovery of several alloys showing considerable dispersion hardening, the most important of which, the alloys of copper with iron, nickel, cobalt and chromium silicides, have since been very ably reported by M. G. Corson.1 This paper is offered as a few notes covering alloys other than those described by Corson and some further data on the silicide alloys.

Jan 1, 1929

By R. W. Vieth, S. A. Bradford

THE orientations of tetragonal tin crystals are commonly examined by either the transmission Laue method or the back-reflection Laue method. The predominant planes and zone axes of the pattern are plotted on a Wulff net and indexed by measuring the angles between planes and directions. The problem of identifying the Laue spots has been approached in several different ways. Nicholas 1 tabulated interplanar angles for ten planes but did not relate the angles to permutation of indices or sign. A table of angles between adjacent planes and of angles between adjacent zones was published by Chandrasekhar and veal.' These tables are very helpful, provided the film shows all the low-order zones that occur within about 20 deg of each other. Frounfelker and Hirthe's compilation3 of angles between the (001) plane and twenty-nine other planes is useful for the indexing, only if the (001) spot can be found on the film. For all but the simplest orientations, however, more information is needed to index the diffraction spots. Standard stereographic projections, such as those published by Bicelli, 4 provide part of the information required. By their nature, these projections show the positions of only a few zone axes. In the tetragonal system many low-order zone axes are not normal to the planes having the same indices. Consequently, planes and directions can have entirely different positions on a stereographic projection. For example, the [011] zone axis is 33 deg from the normal to the (011) plane. The crystallographic orientation usually has to be deduced from a combination of the predominant zone axes and a few low-order planes that appear on the film. In addition to a standard stereographic projection of the planes, a stereographic projection of the directions is needed. Such a projection can be constructed from the angles given in Table I. To provide more information about angles between planes and directions, we have calculated interplanar angles up to (332) and angles between planes and directions up to [332] on an IBM 1620 computer. The angles are differentiated according to permutations of sign and indices. Those doing research on tin single crystals are welcome to request a copy of these tables from the authors.

Jan 1, 1967

By B. W. Frazer

In the numbers of the Engineering and Mining Journal of June 27th and July llth, 1874, there appeared some very complete statistics of the working of some anthracite blast-furnaces belonging to a large establishment in this country, followed by calculations of the heat requirements of the furnaces, similar to those which have been made for European furnaces by Mr. I. Lowthian Bell, Prof. Gruner, Prof. Akerman and others. To the author of these valuable papers, Mr. John A. Church, of New York, the thanks of American iron metallurgists are due for this attempt (the first, to my knowledge at least), to attack systematically and scientifically the problem of economy of fuel in our anthracite blast-furnaces, by applying the formulas obtained from European practice and from the experiments of European metallurgists, to the determination of the amounts and the modes of distribution of the heat production and absorption in our furnaces. In order to facilitate a comparison of the results thus obtained for the anthracite furnaces in question with those obtained for the best types of European coke furnaces, I have reduced 60 the same standad of heat units (the product of the ton and the degree Centigrade), and placed side by side, the calculations of the heat requirements of one of the furnaces of the Clarence works, as given by Mr. Bell, of a furnace at Pouzin, on the banks of the Rhone, given by Prof. Gruner, and of the anthracite furnaces for 1869-73, as given by Mr. Church. Table I shows the different conditions of working of the three furnaces, of which Table II gives the respective heat requirements. I have made this latter table in such a manner as to give for each furnace its heat requirements, both according to the views of Mr. Bell and those of Prof. Gruner. Mr. Bell assumes that all the carbonic acid produced by the decomposition of the carbonate of lime of the charge, is reduced to carbonic oxide by contact with solid carbon ; also, that the carbon of t,he pig iron is a portion of that deposited in the ore in the upper part of the furnace, by the dissociation of carbonic oxide. Prof. Gruner, on the other hand, assumes that all the carbonic acid of the carbonates of the charge escapes unreduced, and that the carbon deposited in the upper part. of the furnace, by the dissociation of carbonic oxide, is again converted into carbonic oxide or

By David W. Wisecarver, James F. Reynolds

INTRODUCTION The Department of Energy is cooperating with Snowmass Coal Company near Carbondale, Colorado to introduce the longwall mining method in moderate to steeply pitching coal seams in the United States. This venture is part of a coal mining research program directed toward development, trial, and analysis of mining technique8 to improve production and recovery in the more difficult mining conditions such as thick, multiple, and steeply pitchly seams found in the Western U.S. The project at Snowmass is the first attempt in the United States to operate a longwall in a steep coal seam. Plans are to mine three adjacent, successively downslope panels in the eight foot thick seam which varies in pitch from 27 to 33 degrees. During this work, researchers and mine engineers are expected to obtain answers to many engineering questions relative to panel design and development, selection of face equipment and beet operating techniques and procedures. They are also committed to obtaining hard data on costs, recovery, production, safety, and behavior of underground mine structure as the three panels are mined. This information is essential to future mine engineering and profitable mining of pitching Western coal reserves. Development of the first trial panel was begun in 1979 and completed in June 1981. The longwall mining equipment was then installed in the starting room and retreat mining begun on August 11, 1981. Project duration is expected to be about five years during which over tm million tons of coal will be produced. TRAINING The longwall mining method is new to Snowmass. For years the mine produced coal by room and pillar methods using conventional techniques to mine upslope rooms and Alpine F6A miners to cut entries and rooms on strike. Miners were experienced in room and - pillar mining from other mines. News of the longwall demonstration was received enthusiastically by Snowmass miners. Employee interest in the project was 100%. However, there was minimal longwall experience on site. In fact, most of the work force had not even seen a longwall. Mine and company management were well aware of the immediate need to develop trained longwall face mining crews and maintenance people qualified to work on longwall equipment and also expertise in longwall planning, equipment selection, power distribution design, ventilation requirements and panel development. The first approach to answer this huge deficiency in longwall mining experience was obviously training. Hence a training program directed toward those mining specifics most urgent to the beginning mining phases was initiated in mid-1980. Classroom lectures and hands on training, using instructors from equipment suppliers and available company longwall expertise, was conducted in longwall subjects to include face mining procedures, panel development, operation of equipment, equipment assembly and maintenance, electrical circuitry and controls, ventilation, move of longwall equipment, and safety procedures. At the same time, responsible engineers and foremen were sent on a tour of European pitching longwalls to see first hand how other mines working under similar seam conditions conducted their operations. Development techniques, types of equipment, methods for transport of men and materials, and ground control techniques were discussed with engineers, foremen and officials at each mine. This look at European longwall mining operations gave Snowmass good insight into the unique problems associated with longwall mining on 30' pitch. Mining considerations such as face conveyor/ support system slippage downslope, panel development, maintenance, safety considerations, manpower requirements, and haulage methods were covered with European experts

Jan 1, 1982

MONTANA SECTION W. C. SIDERFIN, Chairman, OSCAR ROHN, Vice-Chairman, E. B. YOUNG, Secretary-Treasurer, 526, Hennesey Building, Butte, Mont. F. W. BACORN, C. D. DEMOND. The semi-annual meeting of the Montana Section was held at the Silver Bow Club, Butte, Montana, on Friday, Nov. 16, at 8 p. m.; this was a postponement of the regular October meeting because of conflict in date with the St. Louis meeting of the Institute. An informal dinner was served to 68 members and guests. After dinner, Chairman W. C. Siderfin called the meeting to order. The minutes of the annual meeting, of Feb. 2, 1917, and the special meeting of May 21, 1917, were read and approved. C. W. Goodale led the discussion with "Notes on the St. Louis Meeting." He was followed by J. H. Warner who spoke on " The Joplin and Miami Districts," and by J. L: Bruce, Alexander Leggatt, N. B. Braly, and E. B. Young, the latter speaking on the work of the War Minerals Committee; and on the Cosden Oil Refinery at West Tuba, Okla. R. H. Sales reviewed briefly the manganese situation. E. N. Norris presented a paper on "Fire Proofing of Mine Shafts by the Anaconda Copper Mining Co." This resulted in interesting discussion by C. L. Berrien, C. E. Nighman, N. B. Braly, W. B. Daly, B. H. Dunshee, and J. J. Carrigan. C. L. Berrien and C. E. Nighman presented their papers on "Fire Extinction by Hydraulic Filling." In view of the late hour, discussion was waived. The executive committee, by unanimous consent, decided to request written discussion of the above papers to be presented at the next meeting, in February. B. B. Thayer spoke interestingly on the work of the Naval Consulting Board, and referred to the arsenic situation. Spencer Miller, also a, member of the Naval Consulting Board, entertained the-meeting with a vivid description of the method of "Coaling Battleships at Sea." Robert Sticht of Tasmania, in a short talk, spoke feelingly of his relations with the United States. At a late hour adjournment ended a most successful and interesting meeting. E. B. YOUNG, Secretary.

Jan 1, 1918

By B. M. Larsen, L. S. Darken

Some years ago we collated all laboratory data then available to us on the distribution at equilibrium of manganese and of sulphur between metal and simple slags, and used the results in setting up an equation, which proved to be in accord with determinations of the distribution ratio of manganese and of sulphur between liquid steel and open-hearth slag, over a wide range of operating conditions. We now present an outline of our calculations and inferences on these two closely related questions, which are of especial importance because of the advisability of conserving manganese wherever possible. In general, our results show that in the open-hearth furnace equilibrium between metal and slag, with respect to both manganese and sulphur, is substantially attained during the finishing period of the heat, or in about a half hour to an hour after any additions were made. This implies that the end result will be identical whether manganese is added as alloy or metal to the liquid steel or as oxide to the slag. The proportion of total manganese retained by the steel is favored: (I) by use of the minimum amount of lime, consistent with other operating limitations, required to give a lime-silica ratio of about 2.4, which usually corresponds to a minimum practical slag volume; (2) by a high concentration in the slag of MnO relative to FeO; (3) by high operating temperature. Absorption of sulphur by the slag from the liquid metal is favored: (I) by large slag volume; (2) by a high concentration of active (or "free") lime and of manganese oxide dissolved in the slag; (3) by low concentration of silica, iron oxide, and phosphate dissolved in the slag. Distribution 02 Manganese between Slag and Metal at Equilibrium On the basis that the distribution of manganese between liquid steel and slag is controlled by the reaction FeO + Mn -& MnO + Fe [A] slag metal slag metal the distribution at equilibrium, at a given temperature, is expressed by the equilibrium constant for this reaction, which is defined as K,, _ aMnO' afe aFeO ' aMn where a is the activity of the molecular species denoted by the subscript. The activity of each of the several components, although it is not known precisely, is approximately equal to the concentration of each component expressed as its mol fraction; that is, as the ratio of the number of mols of the given component to the total number of mols of all the molecular species present in the metal or slag, as the case may be. Moreover, since the activity, or concentration, of iron in the liquid metal is in fact substantially constant, the term afe may be combined with K" to give a new constant K'. Making these changes, 7

Jan 1, 1942

By B. M. Larsen, L. S. Darken

Some years ago we collated all laboratory data then available to us on the distribution at equilibrium of manganese and of sulphur between metal and simple slags, and used the results in setting up an equation, which proved to be in accord with determinations of the distribution ratio of manganese and of sulphur between liquid steel and open-hearth slag, over a wide range of operating conditions. We now present an outline of our calculations and inferences on these two closely related questions, which are of especial importance because of the advisability of conserving manganese wherever possible. In general, our results show that in the open-hearth furnace equilibrium between metal and slag, with respect to both manganese and sulphur, is substantially attained during the finishing period of the heat, or in about a half hour to an hour after any additions were made. This implies that the end result will be identical whether manganese is added as alloy or metal to the liquid steel or as oxide to the slag. The proportion of total manganese retained by the steel is favored: (I) by use of the minimum amount of lime, consistent with other operating limitations, required to give a lime-silica ratio of about 2.4, which usually corresponds to a minimum practical slag volume; (2) by a high concentration in the slag of MnO relative to FeO; (3) by high operating temperature. Absorption of sulphur by the slag from the liquid metal is favored: (I) by large slag volume; (2) by a high concentration of active (or "free") lime and of manganese oxide dissolved in the slag; (3) by low concentration of silica, iron oxide, and phosphate dissolved in the slag. Distribution 02 Manganese between Slag and Metal at Equilibrium On the basis that the distribution of manganese between liquid steel and slag is controlled by the reaction FeO + Mn -& MnO + Fe [A] slag metal slag metal the distribution at equilibrium, at a given temperature, is expressed by the equilibrium constant for this reaction, which is defined as K,, _ aMnO' afe aFeO ' aMn where a is the activity of the molecular species denoted by the subscript. The activity of each of the several components, although it is not known precisely, is approximately equal to the concentration of each component expressed as its mol fraction; that is, as the ratio of the number of mols of the given component to the total number of mols of all the molecular species present in the metal or slag, as the case may be. Moreover, since the activity, or concentration, of iron in the liquid metal is in fact substantially constant, the term afe may be combined with K" to give a new constant K'. Making these changes, 7

Jan 1, 1942

By Klaus Detert

Fifteen and 18 pct Ni maraging steel and several binavy and ternary alloys of the iron-rich corner of the Fe-Co-Ni system have been studied. After annealing in the austenite range, these alloys were deformed slightly by cold rolling and subsequently aged. Compavison of experimental measurements at various processing stages indicates that small degrees of deforn~ation (5 to 10 pct reduction in thickness) do not influence hardness and strength or the aging kinetics. Electrical resistivity and ductility are somewhat redu]ced and the coercive force is substantially lower when compared to identical samples which were not deformed. The results are explained in terms of retained austenite which transforms into martensite with the small amount of deformation. RECENTLY there has been increasing interest in maraging steel for applications in electric power generators requiring a high ratio of power to weight.' Fifteen pct Ni maraging steel has been investigated to evaluate its properties and performance for application as high-strength magnetic rotor steel,' and a thorough investigation of the precipitation and transformation processes in this alloy has been conducted in this laboratory.3 The influence of deformation, which preceded the aging treatment, was also studied. It was found that a small deformation in the order of 5 pct has a rather striking effect in reducing the coercive force. Other interesting effects on the properties caused by such deformation have led to the more detailed studies reported herein. EXPERIMENTAL METHOD The methods used to produce the samples from 15 pct Ni maraging steel have been described elsewhere.3 The general procedure of hot forging and cold rolling to sheet has been followed. The composition is included in Table I which also contains the composition of the 18 pct Ni maraging steel grade 250 studied. More data about the material and the processing of the 18 pct Ni maraging steel have been recently reported.4 The experimental alloys of binary and ternary Fe-Ni-Co alloys were made by levitation melting in an argon atmosphere and casting into rod-shaped ingots 7 mm thick weighing 20 g. From these ingots 25-mm-long rods were machined to study the phase transformation by a dilatometer. These rods were then cold-rolled to strips, 2.4 mm thick. Annealing for austenitizing was done in tube furnaces in an argon or helium atmosphere followed by cooling in the water-cooled portion of the tube. Aging was done in a salt bath containing a neutral blend of Alkali nitrates and nitrites. Vickers hardness was measured using a load of 50 kg for 15 sec. Tensile tests were carried out on a hard beam tensile tester at a strain rate of 5 X lo-' per sec using flat samples with a gage length of 37.5 mm and a cross section of 1.25 by 6.25 mm. Estimated sensitivity was 5 K x strain and 0.35 kg per sq mm stress. Magnetic saturation was determined on small cylindrical samples, 2.5 mm in length and diameter, by measuring the force exerted by the gradient of a magnetic field of 1000 oe per cm in a mean field of 11,500 oe. The measured values could be reproduced within *1 pct. Coercive force was measured by a precision-type magnetic field probe in a magnetic coil as described by Foerster.5 The magnetizing field was 1300 oe. The samples were 5 cm long, 1 cm wide, and 2.4 mm thick. he coercive force was measured to within +0.1 oe. Electrical resistivity was measured by using a potentiometer on flat strips with a gage length of 100 mm and a cross section of 2.5 by 0.5 mm. The accuracy of the measurement was 0.1 pct but the reproducibility of the measured specific resistivity among different samples was in the order of 1 pct. The method used to prepare the samples for electron transmission has been reported elsewhere.3 RESULTS Fig. 1 shows the influence of deformation after annealing on the resistivity, hardness, and coercivity. The samples were annealed for 30 min at 1000"C,

Jan 1, 1968

By Donald Warren, J. F. Libsch

HIS investigation originated as a result of a pre-vious experimental study' of the magnetic properties of Fe-Co alloys fabricated by the powder metallurgy technique. Densities of powder compacts prepared for the magnetics investigation varied from 7.45 to 7.70 g per cu cm or from 93 to 95 pct of the experimental value of 8.08 g per cu cm for a fused alloy of the same composition.' While this range of density is considered sufficiently high for most applications, the highest possible density is to be desired for maximum magnetic properties. By applying a technique similar to the one described above to a pure electrolytic iron powder, Rostoker³ was able to achieve a density of 7.895 g per cu cm, which is the highest density ever reported for sintered iron. While Rostoker's work involved the sintering of an elemental powder rather than a mixture, it was believed that higher densities should also have been obtained for alloys using the above technique because of the recoining operation and the high sintering temperature. Consequently, it was decided to investigate the various factors affecting the density of this alloy with the idea that such a study might lead to higher densities and, as a result, powder alloys having magnetic properties identical with those of the fused alloys. It was believed that the principal reason that near-theoretical densities for the powdered alloy were not obtained was the interference of gases with the normal sintering mechanism. When present during the sintering operation, gases can exert several harmful effects: they can remain on the particle surface and interfere with surface diffusion and plastic flow; they can be released and, under certain conditions, expand the void spaces through gas pressure; or they can remain trapped in the pores and exert a hydrostatic pressure that retards elimination of the pores. Jones,4 Rhines,5 Goetzel," and others have given the effect of gases in the sintering of powder compacts an extensive treatment. Among the more important sources of gases in the sintering process are dissolved gases, adsorbed gases, air entrapped during pressing, and gaseous products of chemical reactions. During sintering adsorbed gases are partly released at a relatively low temperature, while those gases entrapped during pressing cannot escape until their pressure is increased sufficiently through increasing temperature to expand the interpartjcle openings. The remaining adsorbed gases, gaseous reduction products, and dissolved gases produce a similar effect at the higher temperatures. If, in the sintering process, gas evolution occurs after the interpore channels have been sealed, an exaggerated expansion of the void spaces results. This is particularly true if the temperature is high enough for extensive plastic flow. In his fabrication of powder bars from tantalum, Balke7 had to consider the effect of adsorbed hydrogen and provide for its escape during sintering by limiting the compacting pressure to a maximum of 50 tons per sq in. The effect of gases entrapped during pressing was first noted by Trzebiatowski8 when he found that gold and silver powders decrease in density with increasing sintering temperature if pressed at 200 tsi, while they exhibit the usual increase when pressed at 40 tsi. Recent investigators9-11 have also noted that entrapped gases have an effect on the expansion of copper compacts during sintering. Proper provision for the escape of gaseous products of reduction must be made in order to avoid deleterious effects. Myers" states that in the sintering of electrolytic tantalum powder, the temperature was gradually raised to 2600°F with a pause at 2000°F to permit reduction of the oxides. Experimental Details For the present study, 50 pct Co-50 pct Fe compacts in the form of circular disks 1½ in. in diam and 0.15 in. thick were fabricated by the pressing and sintering of a mixture of the elemental powders. It was decided to follow the sintering process by means of liquid permeability measurements, because it was thought that such measurements might serve as a measure of relative pore sizes, as well as a possible indication of the point at which most of the interpore channels become sealed. However, since the permeability as measured by the flow of a liquid, such as ethylene glycol, does not give an absolute indication of the point where the pores have become isolated, a method for determining the percentage of pores connected to the surface was set up. As an additional cross check on the permeability measurements, metallographic methods were used to study the relative pore size. Finally, the property of ultimate interest, the density, was measured. Raw Materials: The powders used consisted of an annealed, 99.9 pct pure, —150 mesh grade of electrolytic iron powder, and a 98 pct pure, —200 mesh grade of reduced and comminuted cobalt powder. The cobalt powder was not further processed either by hydrogen reduction or annealing. The screen analyses for the iron and cobalt powders are given in Table I, while the chemical analyses for each type of powder are listed in Table 11. Table 111 gives the hydrogen loss measurements for the powders according to the M.P.A. Standard Method and for a higher temperature as well. Preparation of Compacts: Equal amounts of the elemental powders were mixed by rotation for 1 hr and then pressed into compacts approximately 0.15

Jan 1, 1952

By Lee Hillard Meltzer, Ralph E. Davis

INTRODUCTION During the past few years emphasis has been placed upon methods of estimating the future expectancy of gas production from natural gas fields. Before technical methods were applied, the production expectancy over future years was based upon the knowledge of gas well behavior, learned through long experience and embedded in the "know-how" of men long in the gas producing business. It is doubtful that a technical study of future expectancy of a gas field or a group of fields was ever prepared for the preliminary planning of a natural gas pipe line system built prior to about five years ago. The decline in well production capacity was naturally recognized by all familiar with the business since its earliest beginnings more than 75 years ago. In 1953, the Bureau of Mines published Monograph Number 7, "Back-Pressure Data on Natural Gas Wells and Their Application to Production Practices," which gave to the industry the first technical analysis of the decline in production of individual gas wells. This method affords a means of estimating the future production in relation to decline in reservoir pressure. The demand for technical determination of expectancy of future gas productivity from fields or a group of fields led technical men to the application of the knowledge of well behavior to the problems. The decline in a well's ability to produce as pressures declined could be estimated by the use of the curve known as the "back-pressure potential curve" as developed by the Bureau of Mines. A field containing few, or even numerous, wells could be analyzed on the basis of the sum of potentials of all wells. In most studies of this nature, the problem is to estimate the rate of production that can be expected, not only from present wells but also, from wells that will in the future have to be drilled into the reservoir being studied. The "back-pressure potential" method requires that the following data be known or estimated: (1) Proved gas reserves. (2) Current shut-in pressures and rate at which shut-in pressures change with production. (3) Back pressure potential data on wells in the source of supply. (4) Ultimate number of wells which will supply gas, and their potential. (5) Limitations on productivity such as line pressures against which the wells will produce, friction drop in the producing string, and so forth. It is evident that the resulting estimate of gas available in each year for a future of say, 20 years, contains many uncertainties. While the method may have considerable merit for a field that is fully developed, it cannot be completely dependable in fields that are only partially developed. In such cases, some of the data upon which it is based can only be estimated or assumed. In the study of this problem during the past few years, a method has been developed which we believe has great merit, especially when applied to fields subject to substantial future drilling, and when applied to the study of fields which, on the average, appear to have characteristics similar, in general, to the average of the fields used in the development of the "yardstick" outlined herein. From an analysis of the production history of 49 reservoirs which are depleted, or nearly depleted, a curve has been constructed which shows the average performance of the reservoirs during the declining stages of production. When properly applied, this "average performance curve" can be used to determine the stage of depletion at which a reservoir or group of reservoirs will no longer be able to yield a given percentage of the original reserves. "AVAILABILITY" AND "AVAILABILITY STUDIES" The rate at which. a reservoir will yield its gas depends basically upon physical factors, such as the thickness and permeability of the sand, the effect of water drive, if any, and other conditions, and upon economic factors, such as the number of wells drilled. Within the ranges set by the physical conditions, a rate of delivery tends finally to become established. The rate (or range of rates) represents a balance between the interests of the operator, who desires the maximum return from his property and of the pipe line owner, who desires to maintain a firm supply for his market. This balance, which is influenced by the terms of the contract, determines the capacity which will be developed by the operator, and the time and rate at which the decline in production is permitted to occur. Thus the "availability" of gas

Jan 1, 1953

By W. L. Fink, L. A. Willey

DURING the war there was introduced a new higher strength aircraft alloy designated 75S.1,2.3 The properties of this alloy assure extensive applications in both military and commercial aircraft. It is therefore important to understand its limitations as well as advantages. The properties of 75S alloy in the heat-treated tempers, like those of many other aluminum alloys, are affected by the rate of quenching. In general, low quenching rates tend to cause low strengths and to adversely affect the resistance to corrosion. Commercial quenching procedures are usually sufficiently rapid to permit the development of maximum properties. However, in the center of heavy sections, such as large rolled and extruded shapes, the quenching rates may not be rapid enough to develop maximum strength or resistance to corrosion. The investigations of 75S alloy described herein reveal the most critical range of temperature and the effects of quenching sheet and extrusions at different rates through that temperature range, on the tensile properties and resistance to corrosion. PROCEDURE Preparation of Specimens Sheet specimens (3 in. by 9 in.) were prepared from a commercial lot of 75S "as rolled" sheet (0.064 in. thick). The composition° was as follows: Weight Percentage Cu Mn Mg Zn Cr Al with Normal Impurities 1.64 0.16 2.58 5.66 0.27 Remainder The specimens employed for the determination of the time-temperature relations during quenching of sheet were prepared by the following procedure: the hot junction of a 28-ga. iron-constantan thermoelement (asbestos insulated) was brazed to a thin strip of aluminum which was in turn brazed into the end of a 3/16 in. i.d. by ¼ -in. o.d. by 30 in. long aluminum protection tube. Before brazing, the tube was flattened to 0.064 in. thickness over the junction and adjacent lead wires for a distance of 1 ½ in. The flattened end of the tube was fitted into a slot cut from one edge to the center of the 3 in. by 9 in. by 0.064 in. sheet and brazed into place. The brazed joint was dressed to the thickness of the sheet and the entire specimen buffed to approximately the brightness of "as rolled" material. Because of the brazing operations required, these specimens were prepared using 3S alloy. For the investigation of quenching rates in heavy sections, there were used 75S extrusions which had compositions similar to that of the sheet. The specimens consisted of 14 in. lengths of ¾ in., 2 in., 3 in. and 4 in. diam cylindrical rods and a roughly rectangular extruded section which was approximately 4 in. by 7 ½ in. Thermocouples were peened into the bottoms of 1/8 in. diam wells drilled into one end and parallel to the axis to a depth of

Jan 1, 1947

By AIME AIME

THE MODEL LAW previously referred to', in these columns several times, prepared by Engineering Council, to be o ered in any state where legislation is introduced for licensing engineers, is given in abstract below. , Mining engineers throughout the country should watch legislation of this sort and see that the draft prepared by Engineering Council is in the hands of any state legislative committee which proposes to frame a licensing law. So far as this office is informed, the mining engineers are a unit against licensing, but if we must be licensed the most innocuous law that has been submitted is the draft prepared by Engineering Council. ABSTRACT OF MODEL LAW -FOR REGISTRATION OF PROFESSIONAL ENGINEERS, ARCHITECTS, AND LAND SURVEYORS

Jan 1, 1920

By Raymond Ladoo

THE milling of talc, as is the case of many non-metallic minerals, until recently, has not received adequate technical consideration, for the talc industry has become of importance only within the last decade. At first, talc was used only in the massive form, for foot warmers, griddles, and so on, and milling methods were unnecessary. As the demand for ground talc increased, producers adopted the machinery used in the milling of flour; in fact, many talc mills were rebuilt flour mills. Improvement has been slow, but today several types of grinding and separating machinery are in use; many of them, however, are still inadequate and inefficient. To determine the best methods of milling talc, it is necessary to understand the essential properties a talc must possess to fit it for a particular use. For toilet purposes, whiteness, freedom from lime and grit, fineness of grain, and good "slip" are essential. As a paper filler or coating, the talc must be white, have a good slip, be free from grit and iron, uniform, and fine grained; freedom from lime is a disputed point. Fibrous talc is supposed to be superior to massive on account of the interlocking of grains in the paper, thus increasing its strength; this point, though, is in doubt. In general, talc for the paper industry need not be of as high quality or as fine grained as that used for toilet purposes. Talc is usually bought by sample, for which reason it is difficult to state the essential properties for use in paint, rubber, roofing, and so on. The adoption of standard screen tests and standard grades by producers is necessary before an accurate basis for manufacturing or selling standards can be established. Off-color tales might be utilized, as in Germany and-Austria, by the establishment of standard grades of colored tales.

Jan 1, 1921

By Jack M. Swales

Kermac Potash Co., the newest American entry in a rapidly expanding industry, has come on the scene with notable variations in conventional shaft-sinking and mining techniques. Located in the famed potash producing district east of Carlsbad, N. Mex., Kermac started up its mine in November, 1965, to supply ore to the company's 500,000-tpy potash crystallization refinery. In so doing, the company (1) drilled the first large diameter mine shaft in the potash industry and (2) has employed new continuous miners especially adapted for use in thin potash beds. REACHING THE ORE ZONE In its initial mine planning, Kermac, a partnership owned jointly by Kerr-McGee Corp. and the National Farmers Union Development Corp., considered it imperative that the shafts be sunk and equipped as soon as possible and that the mine be developed sufficiently to insure a constant ore feed to the mill when the unit was placed on stream. After examining the alternative sinking techniques available to it, the company decided to accept a proposal by Big Hole Drillers, Inc., to drill the shaft from the surface through various formations of sandstones, siltstone, shales, anhydrite, limestones, dolomite and salts to the potash ore zone.

Jan 12, 1966

By Mark J. Klein

The behavior of nitrogen in Cr-0.12 at. pct Y was studied in specimens of varying interstitial concentration and thermal history. It was found that soluble nitrogen can be introduced into this alloy by increasing the concentrations of either oxygen or nitrogen. For low nitrogen concentrations the nitrogen in solution is low relative to that in unalloyed chromium. However, the nitrogen in solution increases with increasing nitrogen concentration, approaching that in unalloyed chromium. When the alloy is supersaturated with nitrogen, the nitrogen precipitates readily from solution as a chromium nitride. The stress -induced relaxation of nitrogen is influenced by internal oxidation or internal nitrification of this alloy. THE addition of small concentrations of reactive elements such as yttrium have been found to enhance the low-temperature ductility of chromium.&apos; However, the mechanism by which the ductility is increased is not known. It has been suggested that this effect is caused by a drastic reduction in the concentration of nitrogen retained in solution and therefore a decrease in the number of dislocations locked by nitrogen, a factor that has been associated with an increase in ductility.1,2 However, a change in the type of interstitial precipitate induced by yttrium could also contribute to enhanced ductility of the alloy, since chromium nitride precipitates appear to be embrittling.&apos; In this regard, it has been shown that yttrium scavenges nitrogen in chromium to form YN,4 thus reducing the embrittling chromium nitride phase. However, the change in nitrogen solubility induced by yttrium and the partition of nitrogen between chromium and yttrium nitrides are not known. The object of this investigation is to study the effect of yttrium on the behavior of nitrogen in chromium to obtain information relevant to the mechanism by which scavengers enhance the ductility of chromium. EXPERIMENTAL PROCEDURES The experimental procedures used in this investigation have been described in detail elsewhere.5,6 Wires of Cr-0.12 at. pct Y, 15 cm in length and 1 mm in diam, were drawn from rods 0.6 cm in diam supplied by the General Electric Co. The grain size of the wires after recrystallization at 1150°C was somewhat nonuniform, varying from 0.006 to 0.06 mm in diam. The interstitial analysis for the wires in ppm by weight was about 160 0, 80 N, 12 C, and <2 H. Heat treatments were carried out after encapsulation of the specimens in quartz tubes containing argon. Changes in interstitial concentrations, or interstitial "loading" as it is termed in this study, were generally accomplished by annealing in oxygen, ammonia or methane at 1150°C. The internal friction was measured using a conventional torsional pendulum enclosed in an evacuated chamber. Electrical-resistivity measurements were made at liquid-nitrogen temperature.

Jan 1, 1967

By S. G. Valentine

BLAST-FURNACE blowing engines are broadly of two main types: either steam- or gas-driven reciprocating engines, or turbine-driven rotary engines. Some results of experience with a furnace blown by an engine of the latter type may be of sufficient general interest to relate. The first engine of this type was installed at Oxford Furnace, New Jersey, before the writer&apos;s connection with this plant, in March, 1910. This furnace uses chiefly New Jersey magnetites and had been in blast seven months on its old engines when the turbo blower was started. It was 80 ft. high by 17 ft. 6 in. bosh and 11 ft. hearth diameter. It is of interest to see from the records what happened when the turbo engine was put to work. But of course, as the old blowing equipment was rather antiquated, consisting of two I. P. Morris engines with air cylinders 72 by 72 in., in good running order, however, it is evident that the comparison between their work and that of the turbo blower cannot be interpreted as being between machines that were respectively of equal excellence as representatives of their types. Still the results were gratifying and -interesting. The records show that, with the old engines blowing 13,630 cu. ft: of air per minute, measured by piston displacement, the furnace was working up about 480 tons of stock per 24 hr. and producing an average of 132 tons per day and a maximum of 166 tons. The rotary blowing engine installed was a General Electric Co. machine, the driving end being a Curtis steam turbine and the air end a six-stage rotary compressor, all running at about 1,500 to 1,600 rev. per minute, and having a capacity of 25,000 cu. ft. of air per minute up to 25 lb. pressure, and equipped with an automatic constant-volume variable-speed governor. After running this blower, for a period equal to that covered above by the old engines, at an average rate of 15,000 cu. ft. of air per minute, the furnace worked up an average of about 592 tons of material and produced an average of 170 tons per day. Thus, on an apparent increase of 10 per cent. in the air volume there was an increase of about 23.5 per cent. in the materials worked up and of about 28.8 per cent. in the product. For the first calendar month&apos;s operation of the turbo blower, on an average of 15,040 cu. ft of air per minute, there is

Jan 2, 1914

By J. H. Kittel

THE properties of the metal molybdenum have been the subject of recent investigations1,2 = which have included studies of the changes that occur in the metal when it is annealed after having been cold worked. Most of the data which have been reported have pertained to only one aspect of annealing, that is, the conditions under which recrys-tallization has been observecl. The process of recovery which may precede recrystallization docs not appear to have been investigated, and it is the purpose of this note to report observations on the recovery process in cold-worked molybdenum as determined by changes ill the thermoelectric power which occur as the metal is annealed. The measurements were made on commercially pure molybdenum wires which, after annealing at 1035°C in dried hydrogen for 1 hr, were swaged to give a series of reductions up to a maximum of 84.5 pct. The variously cold-worked wires were then annea1c.d in dried hydrogen for periods of 16 hr at progrc:ssively highel. temperatures from 200" to 1000 c with a final annealing treatment of 70 hr at. 1100°C. After each annealing treatment the ther.ma1 emf&apos;s were determined against a length of original unwo~,ked material that had received the initial hydrogen anrit,aling treatment. The difference in temperature between the hot and cold junctions was maintained at about 75&apos;C. and. the thermal emf&apos;s were measured with a potentiometer that could be read. to 0.01 microvolt. Fig. 1 shows the thermoelectric power. (dE/dT) in microvolts per C between annclalcd and cold-worked molybdenum as a function of the degree of cold work. The effect of annealing is shown in Fig. 2. The general shape of the curves in both figures is similar to results which have been obtained for copper." It was observed that after annealing at temperatures as low as 200°C recovery was well under way. The rapid changes irt thermoelectric power observed near 900 C are probably associated with recrystallization, since such a relation has been observed with copper. Beyond 900°C the thermal emf&apos;s changed in polarity. indicating that from this point or1 the specimens were more highly annealed than the standard. Annealing treatments could not be given at temperatures higher than 1100°C due to limitations of the furnace, and it is evident that, since equilibrium values of thermoelectric powers were far from having been attained, temperatures considerably higher are required to fully anneal molybdenum. References Robert M. Parke: Molybdenum, A New High-Temperature Material. Metal Progress (1951) 60, pp. 81-96. * R. A. Long, K. C. Dike, and H. R. Bear: Some Properties of High-Purity Sintered Wrought Molybdenum Metal at Temperatures up to 2400 °F. NACA TN 2319 (March 1951): G. W. Brindley: A Thern-io-Electric Study of the Cold-Rolling and Heat-Treatment of Copper, Report of a Conference on the Strength of Solids. Physical Society, London (1948) pp. 95-106.

Jan 1, 1953