Search Documents

By George S. Rice

Instantaneous outbursts of gas in underground workings are similar in effect to great blasts of explosives, but without heat effects. Fortunately they occur only in a few localities in exceptional coal fields of the world and under exceptional geologic conditions. Such violent outbursts should not be compared with the ordinary outflows of gas into coal mines or with explosions of gas and dust. The phenomenon is essentially one of gas held in circumscribed areas under very high pressure and as a mining face or heading approaches such a place and the mining excavation sufficiently weakens the natural surrounding dam or shell, this is burst by the pressure just as by the discharge of a mass of explosives. The outbursts, so far as known to the writer, have been confined to coal beds and have not occurred in other mineral deposits. Hence, as discussed later, he believes that it is the relation of the gases to the coal material that is a factor in conjunction with others in producing conditions which permit the phenomena to occur when mining is done. The gases in most instantaneous outbursts have been hydrocarbon gases but in two coal fields they have been definitely found to be chiefly or wholly carbon dioxide. One of these localities in which CO2 outbursts have been frequent and have caused loss of life is in the southern part of the Gard basin, near Alais, in southern France. In 1919, the writer visited the Fontaine mine in this field the day following the occurrence of an outburst by which two men were smothered by carbon dioxide and fine dust. After 24 hr. the CO2 had not been entirely removed by the ventilating current. Occasional outbursts of CO2 have also occurred in other small basins in France, causing accidents, as in Puy-de-Dome. However, mines in the Gard basin, north of those in which CO2 outbursts have occurred, have experienced hydrocarbon gas outbursts. In the Lower Silesian coal field, Germany, there is a group of mines which have been subject to many instantaneous CO2 outbursts, some causing serious accidents, but the greatest disaster occurred recently

Jan 1, 1931

By Alexander N. Mitinsky

UP to a certain limit, the increase of pressure on the diamond-drill increases the rate of progress in drilling. That limit is set by the resistance of the diamonds to compression; and beyond it, the destruction of the stones will involve an. economic loss, both in time and in money. It is, therefore, important to all diamond-drillers to know what is the resistance mentioned. In Europe, operators usually follow an empirical rule, which directs the maintenance of a pressure, on the area-of the bottom of the drilling-tool, of 12 kg. per sq. 4m. For the tools in ordinary use, this is equivalent to 1 kg. per sq. mm. of the diamonds set in the tool So far as I know, American drillers are using pressures as high as 50 to 60 kg. per sq. cm. of the total area of the drill, and the consumption of diamonds (on Denny's authority, 0.2 carats per meter bored) is greater in America than in Europe. But the reason for this difference may be the comparatively larger size of the diamonds commonly used by American drillers. With the assistance of my friend, the late S. Woisslaw, who was the pioneer of diamond-drilling in Russia, I selected from his stock a number of black diamonds, which I subjected in my laboratory to compression-tests. To prepare regular cubes for such tests, as is generally done with other stones, would have been not only costly, but, what is more important, practically useless. I therefore determined, in order to assimilate as nearly as possible the conditions of actual use, to place each sample between a hard plate (corresponding to the rock) and a softer plate (corresponding to the bottom of the tool), into which it would be pressed during the test.

Jan 1, 1906

By Michael Tenebaum, C. C. Brown

In recent years, the importance of slag control in basic open-hearth operations has been universally recognized. To effect such control during the working period of the heat, methods have been developed to measure or estimate slag oxidation and slag basicity. While satisfactory rapid chemical methods have been developed to determine slag oxidation, no completely adequate method of evaluating basicity has yet been provided. The most generally accepted control methods of measuring slag basicity are based on visual cstimates. While considerable benefit may be derived from such estimates, the need for some measurable indication of slag basicity has become increasingly apparent. In a recent paper, Philbrook and Jolly suggested a promising technique for making the basicity determination. Their method consists of measuring the pH of a mixture of powdered open-hearth slag and distilled water. It was found that a relation could be established between the slag basicity and the alkalinity of the water mixture as measured by the hydrogen-ion concentration. The general procedure followed in making the measurements and the considerations involved in constructing the original curves are given in the paper of Philbrook and Jolly and need not be repeated. It is the purpose of this paper to discuss some of the factors considered in applying the pH measurements to actual slag control and to present some of the results of its apphcation. Factors Involved in Measuring pH of Water-slag Mixtures To facilitate the application of the pH control system, it was desirable that no alteration be made in the routine methods of sampling and crushing the furnace slag. Some of the factors considered before establishing a curve to relate slag basicity with the pH reading arc reviewed individually in the following paragraphs. Effect of Cooling Rate Under actual operating conditions there can be considerable variation in the temperature of the piece of slag crushed for the pH determination. To determine whether variations in crushing temperature or in cooling rate would affect the pH reading, a series of four samples was prepared from each of two separate slags. These samples represented conditions far more extreme than would actually be encountered. To obtain these samples, a thick pancake of slag was poured. One piece of this pancake was crushed immediately after it had solidified. Another piece was water-quenched and then crushed. A third piece was allowed to air-cool to room temperature before crushing. The fourth sample was prepared from a chilled slag. This sample was poured onto a heavy inclined steel plate at the

Jan 1, 1945

By Sam Tour

Some years ago, the writer described heat checks or thermal cracks that occur in die-casting dies.' The life of dies was considered in relation to. the casting temperature, the material used for the die and the heat to be absorbed by the die per unit volume of casting made. The mechanism of the action that results in thermal failure of dies was described. In the present paper the writer proposes to describe some additional observations in regard to heat checking, make one or two suggestions as to the method or methods for further attack of the problem, and give the results obtained on some work carried out along these lines. Importance of Heat Checking Heat checks in steel are the source of trouble in many industries besides that of die casting. Every shop where metals are subjected to hot working is searching for improvement and hoping for a cure. The development of a material of sufficient strength to be used as a die and yet devoid of the property of heat checking would be a godsend to many shops and many industries. The need for thorough study and research on the subject is evidenced by the wide variety of hot-working die steels on the market. It is peculiar, but true, that in practically every case the maker of the steel can give concrete evidence to prove his contention that his type of hot-working die steel is as good as or better than any other. A number of steel companies have several hot-working die steels from which choice can be made to fit a particular set of requirements. Possibly to expect one material to be universally the best hot-working die steel is unreasonable. In some hot-working operations, as in drop forging, the die must have great toughness to withstand the stresses developed; in other operations, as in hot piercing or punching, resistance to erosion at high temperatures, possibly defined as strength and hardness at elevated temperatures, is required. In still others, as in die casting, only sufficient hardness to resist scoring between moving surfaces is required, whereas the resistance to sudden changes in temperature must be at a maximum.

Jan 1, 1935

By Sam Tour

Some years ago, the writer described heat checks or thermal cracks that occur in die-casting dies.' The life of dies was considered in relation to. the casting temperature, the material used for the die and the heat to be absorbed by the die per unit volume of casting made. The mechanism of the action that results in thermal failure of dies was described. In the present paper the writer proposes to describe some additional observations in regard to heat checking, make one or two suggestions as to the method or methods for further attack of the problem, and give the results obtained on some work carried out along these lines. Importance of Heat Checking Heat checks in steel are the source of trouble in many industries besides that of die casting. Every shop where metals are subjected to hot working is searching for improvement and hoping for a cure. The development of a material of sufficient strength to be used as a die and yet devoid of the property of heat checking would be a godsend to many shops and many industries. The need for thorough study and research on the subject is evidenced by the wide variety of hot-working die steels on the market. It is peculiar, but true, that in practically every case the maker of the steel can give concrete evidence to prove his contention that his type of hot-working die steel is as good as or better than any other. A number of steel companies have several hot-working die steels from which choice can be made to fit a particular set of requirements. Possibly to expect one material to be universally the best hot-working die steel is unreasonable. In some hot-working operations, as in drop forging, the die must have great toughness to withstand the stresses developed; in other operations, as in hot piercing or punching, resistance to erosion at high temperatures, possibly defined as strength and hardness at elevated temperatures, is required. In still others, as in die casting, only sufficient hardness to resist scoring between moving surfaces is required, whereas the resistance to sudden changes in temperature must be at a maximum.

Jan 1, 1935

By Charles J. Moore

It seems a duty incumbent on the older members of the Institute to set forth in permanent form some of the results of their experience for the benefit of the younger members; this is the principal object of the present paper, which is the result of a recent examination requiring somewhat unusual geologic investigation. History. The London vein mas first discovered by float and occasional outcrops in the year 1873, four years before the great lead carbonate discoveries of Leadville, but the mine was not definitely located and opened until two years later, when the present locations, Mother, Paris, London, and Hard to Beat, were surveyed for patent. Since 1875 the London mine has been worked almost continuously until 1911, when the force was reduced to a few men only. In its early life the ore was assumed to be free-milling gold-quartz, although lead was a constituent of the vein throughout, and much useless expenditure was made in the erection and operation of a free-gold stamp-mill, with plates and tables for saving concentrates. The vein then opened was in the porphyry-limestone contact, a siliceous lead-ore, clearly most amenable to reduction by lead-smelter. The losses due to this process led in time to the close of the mill. For 20 years past, the mine has been worked under lease and the ore shipped to the lead-smelters in Denver or Salida. In January, 1912,I examined the mine to ascertain whether it was advisable to run a cross-cut tunnel some 4,200 ft. in length to intersect the main vein at a depth of 650 ft. below the present lowest workings. Finding a greatly-faulted zone, a close determination of the geological conditions became necessary to the solution of the problem.

Jan 1, 1914

By Perry Harrison

THE increased use of sintering for the beneficiation of iron ores and the reclaiming of flue dust creates a lively interest in sintering costs and, economics. The character of material sintered and geographical location of plants so radically alter sintering costs and economics that it is well to understand at least the basic elements which control such changes. The following cost factors are believed to be roughly approximated for large-scale Dwight-Lloyd 'continuously operated sinter-machine installations located anywhere. PER CRUDE TON Labor, supplies and repairs 0.15 Power 6.5¢ X kw-hr. rate ? Plant overhead and administration 0.05 Depreciation per ton annual capacity 0.05 Fuel: 6 per cent coke breeze or equivalent minimum ? 1 per cent coke breeze additional for each 5 per cent free and combined water in ore or dust ? Ignition distillate at 0.6 gal. per ton ? PER SINTER TON Royalty on Ore 0.10 Royalty on Flue Dust 0.15 PER CRUDE TON "Winter expense"; i. z., the cost of the five months enforced idle . period for plants tied in to Great Lakes transportation season 0.03 Using the foregoing data, it is possible to roughly approximate the cost of efficient sintering at any location for. any ore, viz:

Jan 1, 1932

By M. J. Pool

The partial molar heats of solution in liquid tin of cadmium, silver, tellurium, and zinc have been measured at 655°. 700°, and 750°K by liquid-metal solution calorimetry. Silver, cadmium, and zinc are endothermic at these temperatures while tellurium is exothermic. Only the heat of solution of silver depends on composition while all four elements show a temperature-de pendent heat of solution. The heat of solution of tellurium is constant up to 0.6 g-at. pct, becomes increasingly more exothermic, and reaches a limiting value at 1 g-at. pct Te. The limiting value has been used to calculate the heat of formation of SnTe at 750°K. The heat effects associated with the dissolution of the compounds Ag2 Te, CdTe, and ZnTe in liquid tin were measured at 750°K. These values are cotnOined with the measured hat effects at 750°Kfor silver, cadmium, tellurium, and zinc to detertrline the heats of formation of the telluride compounds. Cadmium lelluride exhibits a heat of dissolution which has a compositional dependence. THERE is a considerable amount of interest in the compounds of tellurium because of their electronic properties. Both cadmium and zinc tellurides are thermoelectric materials and considerable work has been done on their electronic properties but a limited amount of data is available on their ther-modynamic properties. This work was undertaken to elucidate the heat of formation data on cadmium and zinc telluride. Since both cadmium and zinc are in Group II it seemed to be of interest to compare the values obtained for them with the heat of formation of a Group I telluride. Silver telluride was selected for this comparison. In the course of the work it was also possible to determine the heat of formation of tin telluride and therefore to make a comparison of some of the Group I, 11, and lV tellurides with the metallic elements silver, cadmium, and tin being in the same period. There is also a great deal of interest in the energetic changes which occur upon addition of solute elements to a common solvent. This investigation provided an opportunity to study the partial molar heats of solution of silver, cadmium, tellurium, and zinc in liquid tin. The partial molar heats of solution are of theoretical interest because solute-solute interactions are a minimum in dilute solutions and application of solution models is simpli- fied. In order to complete the analysis of solute-solute and solute-solvent interactions the temperature dependence of the partial molar heats of solution was also measured. MATERIALS AND EXPERIMENTAL PROCEDURE All materials were of the highest purity available. The silver, zinc, cadmium, and tellurium were obtained from American Smelting and Refining Co. and were reported to be 99.999 pct pure. The silver telluride, zinc telluride, and cadmium telluride were obtained from Atomergic Chemetals Co., a division of Gallard-Schlesinger Chemical Manufacturing Corp., and were electronic-grade material of 99.999 pct purity. Tin used for the solvent bath and for calibration was obtained from the Vulcan Manufacturing Co. and was reported as being 99.99 pct pure. The liquid-tin solution calorimeter used in this work is similar in principle to the differential twin-type calorimeter described by K1eppa.l Two of three identical calorimeter wells are used together during any set of experiments, one well being active and the other being passive. The wells are positioned 120 deg apart in an aluminum calorimeter block. Each well contains a multijunction thermopile and a Pyrex test tube to hold the liquid metal bath. Forty-eight of the thermopile junctions are distributed over the surface of each calorimeter well adjacent to the test tube and serve to integrate the heat effects occurring. The other forty-eight are next to the aluminum calorimeter block. The thermopiles for the three wells are connected differentially so that any change in temperature at the outer junctions (which will be the same for both wells because of the high conductivity of the aluminum block) will oppose for the two wells and result in no shift of the zero. The electrical output represents the true temperature difference between the two reaction vessels. A reaction occurring in the active well gives a comparison with another body of very similar thermal properties. In this way, any spurious heat effects due to slight temperature drifts within the entire calorimeter block are eliminated. The output of the differential thermopile goes to a dc amplifier with multiple ranges of from * 10 pv to 1 30 mv. The output of the amplifier is then fed into a Leeds and Northrup strip-chart recorder. The adiabatic temperature change is then calculated using the technique of Howlett, Leach, Ticknor, and ever.' The aluminum calorimeter block is contained in a cylindrical furnace with main and control heaters

Jan 1, 1965

By W. N. Lacey, R. H. Olds, B. H. Sage

Samules of liquid and gas were obtained from the primary separator of a well in the Paloma field. The volumetric properties of the samples and of six systematically chosen mixtures of the samples were experimentally determined at 100°, 190°, and 250°F. at pressures up to 5000 lb. per sq. inch. From these data the influence ,of pressure and temperature upon the composition and specific volume of the bubble-point liquid and of the retrograde dew-point gas was established, The formation volumes and gas-oil ratios of the rnixtures investigated were calculated on the basis of the plant-product oil, which is defined as the isobutane and less volatile portion of each mixture. The results are presented in graphical and tabular form. The volumetric behavior of the mixture corresponding to that produced by the well at the time of sampling was determined for 235ºF., the reported reservoir temperature, by graphical interpolation of the experimental data with respect to composition and temperature. The results indicate that the well-production mixture probably existed as a gas at its retrograde dew point under the conditions of temperature and pressure believed to prevail in the producing zone at the time of sampling. The effect upon the phase behavim occasioned by the omission from the well-production mixture of certain components of intermediate molecular weight was investigated. In the first case, all of the isobutane and 11-butane, and substantially all of the iso-pentane, were removed from the mixture of trap samples corresponding to the well production. In the second case, all the propane, isobutane and n-butane, and substantially all of the isopentane, were removed. Both modifications led to considerable increases in the retrograde dew-point Pressure at 235ºF.; an increase of 558 lb. Per sq. in. above that of the unmodified well-production mixture in the first case, and an increase of 1208 lb. Per sq. in. in the second. It was concluded that the material? remaining after the removal of certain components of intermediate molecular weight could not be injected back into the reservoir in the saqe proportion in which they were produced without entailing appreciable loss of liquid material through condensation within the formation. Introduction Under the usual conditions of production practice, petroleum arrives at the surface of the earth in a physical state considerably different from that in which it existed in the underground reservoir. The relative rates of production and the properties of oil and gas measured at surface conditions do not constitute, in general, even a qualitative description of the fluids existing in the reservoir. The estimation of reserves and the attainment of optimum efficiency with regard to rate, quantity, and cost of production require accurate data concerning the physical properties of petroleum throughout large changes in pressure and temperature. Many schemes have been devised for predicting the behavior of propane, as it is encountered in nature? but the experimental work upon which these predictions are based has not, for the most part, been extended to the higher pressures that occur in practice, nor do these methods permit, as yet, the estima-

Jan 1, 1945

By R. W. Gurry

IN the course of a series of measurements of the rate of diffusion of carbon in austenite at about 960°C. (1760°F.) and 1110°C. (2030°F.), it became necessary to determine carbon concentration when austenite is saturated with graphite, because of indications that the hitherto accepted value of the solubility of graphite in this temperature range is too low. Specimens of carbonyl iron were saturated at temperature in a hydrogen-toluene atmosphere which was in equilibrium with graphite. The carbon content of the steel was measured either by combustion or by the loss of weight after substantially complete decarburization in an atmosphere of hydrogen saturated at room temperature with water vapor. The absence of carbide or graphite as a phase at temperature was demonstrated by microscopic examination of saturated specimens that had been drastically quenched. The mean result of concordant measurements is that gamma iron saturated with respect to graphite contains 1.39 per cent carbon at 957°C. (1755°F.) and 1.89 per cent at 1110°C. (2030°F.). These two values, plotted along with what appears from the literature to be the best value (0.69 per cent) at the iron-graphite eutectoid temperature (738°C. or 1360°F.), yield a curve that is almost linear, and which, continued upward through a short interval, leads to a limiting solubility of 1.98 per cent at the iron-graphite eutectic temperature 1135°C. (2075°F.) instead of the commonly accepted value of about 1.7 per cent. EXPERIMENTAL PROCEDURE The samples of carbonyl iron, with the exception of those for microscopic examination, were cylinders 3.8 cm. long, 0.475 cm. in diameter. They were placed in a graphite holder and suspended in a vertical furnace, the temperature of which was controlled precisely by means of the resistance of the platinum winding.1 In the empty furnace the range of temperature over a distance of 4 cm. at the heat center was 9°C. (16°F.) but at a given location the temperature remained within ±0.5°C. (0.9°F.); it was measured by inserting a platinum-rhodium couple calibrated at the melting point of palladium, 1555°C. Since the presence of the sample probably improved the uniformity of temperature, it was decided to consider the average temperature of the sample to be 3°C. lower than the maximum measured in the empty furnace with the same setting of the controller. Data were obtained in the vicinity of two temperatures, 960°C. (1760°F.) and 1110°C. (2030°F.). The samples for microscopic examination, 2.2 cm. long, 0.475 cm. in diameter, were suspended individually on pure iron wire; for these no temperature correction was applied. The carburizing gas passed into the furnace was dry, oxygen-free hydrogen saturated at room temperature with

Jan 1, 1942

By Mark J. Klein, A. H. Clauer

The Snoek peak induced by solute nitrogen in chromium was studied. A rapid quenching rate is required to maintain nitvogen in solution in sufficient concentrations to be detectable by internal-friction techniques. An expression for the tertninal solubility, c, of nitrogen in weight pevcent is log,,c = -4130/T + 1.05. The diffusion of nitrogen in zhromium determined by internal friction is SNOEK&apos;S theory1 of the stress-induced ordering of interstitial solute elements in the bcc lattice has been used to deduce information on the behavior of interstitials in a number of bcc metals. Under the proper conditions, internal-friction studies of "Snoek peaks" permit a determination of diffu-sivities, solubilities, and precipitation kinetics of interstitial elements. Internal-friction studies of this type have been reviewed by Nowick,&apos; Wert,= Powers and Doyle,4 and others. The behavior of interstitial atoms in Group V-A metals and iron has been rather extensively studied in this way, and results are reasonably self-consistent. However, the study of interstitial elements using internal friction in the Group VI-A metals—tungsten, molybdenum, and chromium—is much less clear. Thus far, internal-friction studies have revealed a peak in tungsten tentatively attributed to carbon5 and a peak in chromium associated with nitrogen. In chromium, Bungardt and Preisendanz6 observed a peak at 180°C for a frequency of -1 cps which they associated with nitrogen. More recently, de Morton7 determined the diffusivity of nitrogen in chromium from studies of a nitrogen peak at 160°c for a frequency of -1 cps and from elastic aftereffect measurements. The objective of this investigation was to study the nitrogen peak in greater detail, to obtain information on the behavior of nitrogen in chromium. This information is of interest because nitrogen is known to have an embrittling effect on chromium. However, efforts to deduce the role played by nitrogen in influencing the mechanical behavior of chromium are handicapped by lack of information on its behavior and distribution in chromium. EXPERIMENTAL PROCEDURES The chromium wires used in these studies were drawn from arc-melted iodide-chromium stock that had been extruded, swaged, and centerless-ground to 0.25 in.-diameter rods. Internal-friction measurements were made in an evacuated torsional pendulum similar to the one described by Kê,8 utilizing wires 0.048 to 0.030 in. in diameter. A series of analyses of the fabricated wires showed that the major impurities were approximately 100 ppm Fe and a combined interstitial content of 50 to 100 ppm C, O, N, and H. A typical interstitial analysis of the wires after processing is 15 ppm C, 2 ppm H, 50 ppm O, and < 5 ppm N. Interstitial concentrations were determined by vacuum-fusion, combustion-conductimetric, and micro-Kjeldahl analyses. In general, vacuum-fusion analysis yielded a lower nitrogen concentration than did micro-Kjeldahl analysis. For consistency, the nitrogen concentrations reported in this investigation were determined by the former method. Heat treatments were carried out by encapsulating the specimens in quartz tubes containing argon. The fabricated wires were annealed at 1150°C for 1 hr to produce uniform recrystallized grain size of about 0.015 mm. Nitrogen and carbon were added to the fabricated wires by encapsulating them in a quartz tube containing ammonia or methane, and annealing them at 1150°C for 48 hr. In some instances, carbon was also introduced by coating the wires with carbon black prior to annealing.

Jan 1, 1965

By R. A. Hadfield

It seems a specially fitting opportunity to present a paper on the alloys of iron and aluminum at the New York meeting of this Institute, owing to the fact that America has, more than any other country, originated and developed the manufacture of cheap aluminum. The Cowles, Castner, and Hall systems have all originated in the ever-busy brain of our cousin across the water. The problem of cheaply producing this valuable metal has been a difficult one, but to the writer it seems that the more arduous the task the greater the delight with which our American friend attempts to overcome the difficulties surrounding it, and the more vim he throws into the work. Another and equally striking proof of this is to be found in the recent appearance of the already wellknown remarkable work, The Mefallurgy of Steel, by Mr. H. M. Howe, of the Institute of Technology, Boston, Mass. It is to be hopel that this Institute will not be slow to recognize by some special mark its appreciation of this signally valuable and original work. The writer has been led to describe the following experiments, believing that so far no full and exact report has yet been presented to this Institute as to the effect of aluminum alloyed or combined with the metal iron. It has been a special object to make the material as far as possible a true alloy or combination of aluminum and iron, with as small quantities as possible of other disturbing ingredients, such as silicon, manganese, etc. In the material described in these experiments, the total amounts of other elements present (sulphur and phosphorus being disregarded as present in such small quantities) do not exceed about 0.5 per cent. Such material may therefore be probably taken as fairly illustrative of the effect of the metal aluminum upon iron. Since completing the experiments the writer

Jan 1, 1891

By E. J. Bonet, P. B. Crawford

It is fairly common practice to reinject water into the aquifer near the oil-water interface in water-drive reservoirs. There have been many studies of aquifer behavior without reinjection,l-5 but apparently no analytical studies have been made to indicate performance when injection wells are present in the aquifer. The diffusivity equation may be used to describe the pressure behavior in an aquifer. When sources are present it can be written as A general solution of Eq. 1 may be obtained as the sum of two solutions. One is a general solution of the homogeneous equation, obtained by dropping the source term in Eq. 1 and still satisfying the required boundary conditions. Another is a general solution of Eq. 1 satisfying homogeneous boundary conditions.1° The first solution, which corresponds to the aquifer without reinjection, has been given quantitative and qualitative treatment in the literature.l-5,8,9 The latter solution will be treated here. Solutions with variable injection rates are obtained by superimposing solutions with constant rates, so we have considered only the latter. Five cases have been treated here: 1. A linear aquifer of finite width and extent. Water is injected into the aquifer at point xo, yo at constant rate. The pressure along the line x = 0 is maintained at zero pressure. (See Fig. 1.) Equations showing the pressure distribution, rates, velocity and cumulative influx have been developed. Certain numerical results are shown. 2. A linear aquifer of finite width and extent. Water is injected into the aquifer at point xo, yo at constant rate. The rate of production along the oil-water water contact is maintained constant. Equations showing the pressure distribution inside the aquifer are presented. 3. A linear aquifer of finite width and extent. Constant pressures are maintained at opposite ends of the aquifer. Water is injected at constant rates at point xo, yo. Equations showing the pressure distribution are shown. 4. A linear aquifer of finite width and infinite extent. The pressure is maintained constant at the oil-water contact. Water is injected at a constant rate at point xo, YO. 5. A linear aquifer of finite width and finite extent. The pressure at the oil-water contact is maintained constant. Water is injected at constant rate per unit length along a line x,. The Linear Aquifer The linear closed aquifer, performing at constant terminal pressure was selected as the first case to be analyzed. The development of the equations is based on uniform injection per unit of thickness, and gravity effects are neglected. In practical application this condition is probably most closely achieved when the

Jan 1, 1970

By S. J. McCarroll

Fig. 1—The belt shown at right carries filter cake to mixing station over calciner. Crude ore conveyors appear in right background. THE Three Kids mine, some six miles east of Henderson, Nev., is in a typical southwest desert area, with high dry summer heat and cool to cold winter seasons. The manganese deposit was located during World War I.&apos; During this period 15,000 to 20,000 tons of ore assaying up to 41 pct manganese were shipped. Interest in the deposit was not revived until the middle thirties, when experiments on the ore were initiated. Test work indicated possible recovery of only 70 pct by flotation, but in 1941 additional work was done at the Boulder City pilot plant of the U. S. Bureau of Mines and also by M. A. Hanna Co. As a result, the Manganese Ore Co. was formed and a plant utilizing the SO2 process was constructed. Numerous operation difficulties ensued, and the plant. was closed when the manganese situation in the country eased. In 1949 Hewitt S. West initiated negotiations to acquire the plant. In 1951 Manganese, Inc., was formed and contract entered into with the General Services Administration to supply 27 million units of metallurgical grade manganese in the form of nodules to the national stockpile. A second contract was made to upgrade 285,000 tons of stockpile ore. Test work was undertaken by the Southwestern Engineering Co. and likewise by the Boulder City pilot plant at the U. S. Bureau of Mines. Results obtained indicated the commercial feasibility of the flotation process. Construction of the plant, which is shown in Figs. 1 and 2, was started in June 1951, and operations on a break-in basis began in September 1952. Apart from the usual starting difficulties two major disasters caused serious setbacks, one a kiln failure in February 1953, and the other a fire that destroyed the flotation building in June of the same year. The nodulizing section of the plant resumed operation in November, and the flotation section in January 1954. The ore minerals are chiefly wad,* with minor amounts of psilomelane, and occur in sedimentary beds of volcanic tuff. The ore is overlain with beds of gypsum which outcrop or may be covered with surface gravel. Intermediate beds of red and white tuff occur frequently with lenses of red and green jasper and stringers of gypsum and calcite. Small amounts of iron are present; lead content averages about 1.0 pct and minute amounts of copper and zinc are found. Barite, celestite, and bentonite are present. Since these are made up of minute asicular crystals, moisture content is very high, averaging about 18 pct. Ore reserves have been estimated at 3 million tons averaging 18 pct Mn2 and up to 5 million tons after grade is dropped to 10 pct Mn. A good part of the orebody was stripped of overburden by the previous operating company . Approximately 50 pct of the ore, representing more than 60 pct of the manganese, can be mined by open-cut methods. A system for underground min- . ing has not yet been decided on. Open-cut mining with benches of 20 ft has proved satisfactory. Although the ore is soft and appears dry and dusty it has a certain resilience, probably due to the porosity and moisture which makes drilling and fragmentation difficult. Wagon drills have been abandoned in favor of the Joy 225-A rotary drill which will put down a 43/4 -in. hole at the rate of 2 ft per min. Holes are spaced in a pattern with 8 to 9-ft centers. Forty percent powder has been used, but better breaking to 2-ft size is obtained with low velocity bag powder of 30 pct strength. Loading is done with one 21/2-yd shovel, and cleanup follows with one D-7 bulldozer. The ore is hauled with Euclid trucks about 1000 ft from the pit to a blending pile, where the daily mine production is spread in layers by bulldozing until approximately one month&apos;s mill feed is accumulated. A new pile is then started and mill feed is drawn from the first pile by one 13/4-yd shovel and Euclid trucks, with a haul of approximately 500 ft. Mining is performed by an independent contractor with engineering and supervision by the company staff. Early test work indicated that the manganese could be floated with soap, a wetting agent, and fuel oil to give a recovery of better than 75 pct with a grade of 43 pct Mn. The concentrate when nodulized with coke would upgrade to 46 pct Mn or over, and the lead volatilized to 0.6 pct residual.

Jan 1, 1955

By R. J. Watson, A. H. Juch

About half a million sucker-rod pumps are installed in oil wells in the U. S. alone. In Venezuela, too, the system is widely used; some 5,000, or 90 percent, of Cia. Shell de Venezuela&apos;s wells produce a total of 400,000 BOPD by this method. Most of the crude pumped is viscous, gassy and contains relatively small amounts of free water. API gravities vary from 90 to 16O; dead oil viscosities vary from 10 to 10,000 cp at the pump; and GOR&apos;s range from 100 to 2,000 cu ft/bbl. Pumps are set at depths ranging from a few hundred to 6,000 ft; the average setting depth is about 2,500 ft. From the literature, it appears that although recent years have seen significant progress toward understanding the rod pumping system as a whole, relatively little attention has been paid to those key items, the sucker-rod pump and the subsurface gas separator or gas anchor. Perhaps because of proration in the U. S., pump manufacturers have seemingly concerned themselves more with the durability of their product, achieved mainly through robust design and metallurgical know-how, than with its working efficiency. In 1963, CSV commenced a major rehabilitation and expansion of its heavy oil fields along the Bolivar Coast. The advent of the more efficient gravel-packed completion and of large-scale thermal recovery (mainly steam soak) operations resulted in well potentials *Now with B. I. P. M., The Hague, The Netherlands. greater than pump capacities. Hence, an urgent need arose to improve over-all pump efficiencies and to attack those special problems related to the production of both the extremely viscous and the hot, steam-laden crudes that formed an increasing proportion of the total stream. There followed a detailed investigation and testing program, carried out in close cooperation with a major pump manufacturer. This culminated in the introduction to the oil industry of a new line of sucker-rod pumps. Early Investigations and Experiments Field Tests Extensive field tests were carried out in three primary Bolivar Coast wells with an in-situ dead oil viscosity ranging from 400 to 6,000 cp. In these installations provision was made to (1) monitor bottom-hole pressures below, in and above the pump by means of pressure transducers, and record casing- and tubing-head pressures continuously; (2) measure accurately the annulus gas, as well as measure the tubing gas and liquid production from the well; (3) take special PVT samples of the well fluid; (4) measure power consumption of the prime mover; and (5) measure the rod loads at the polished rod. A typical test installation is illustrated in Fig. 1. It was established from the pressure transducers that with viscous oils, there is considerable flow resistance across the pump and gas anchor assembly. Pressure surges were observed over each pump cycle,

Jan 1, 1970

By C Woodward

AT the Belmont mine of the Anaconda Copper Min-ing Co., Butte, Mont., a new double-drum electric main hoist and a single-drum electric auxiliary hoist have recently been placed in operation to meet the demand for greater hoisting depths, and to replace a steam-driven hoist which was inefficient and inade-quate for the new conditions. The ease of operation, safety, and efficient consumption of power of the main hoist all tend toward improved hoisting conditions. It consists of a 2150 hp. d. c. motor, directly connected to a shaft carrying two drums equipped with clutches and brakes. The auxiliary hoist consists of a 1000 hp. d. c. motor directly con-nected to a single drum provided with the necessary brakes. Fig. 1 shows the general arrangement of the complete installation, with idler towers and head-frame. The headframe is built of Bethlehem H and G rolled sections, equipped with two 12-ft. dia. cast steel sheaves for the main hoisting ropes. The sheaves are mounted 129 ft., 6 in. above the collar of the shaft; and above them trolleys are provided for their removal or repairs. Between the headframe and the hoist machinery are two idler towers for supporting the ropes on 3-ft. man-ganese steel idlers provided with roller bearings which fleet on a fixed shaft. As a city street is between- the mine headframe, and hoists, it is necessary to protect the thoroughfare from drippings of the preservative compound used on the ropes which pass over the street. For this purpose, at the point where the hoisting ropes cross the street ,a bridge of trusses, supported on columns and roofed with corrugated iron, is provided from property line to property line. Since one of the idler, towers is set close to the street, a part of the structure is built in-tegral with the street covering. The general design of idler tower as well as the covering over the street is shown at A in Fig. 1.

Jan 9, 1927

By J. Chipman, H. A. Wriedt

DURING the past twenty years, a considerable background of knowledge has been built up on the chemical behavior of oxygen in liquid iron. Little is known regarding oxygen in liquid nickel or the effect of nickel as an alloying element on the behavior of oxygen in liquid steel. The solubility of oxygen in liquid iron was determined by Fetters and Chipman&apos; and, more precisely, by Taylor and Chipman.&apos; The Ni-NiO eutectic was placed by Merica and Waltenberg"&apos; * at 1438°C and 0.24 pct 0, and this point has been confirmed by others." O It was reported by von Bohlen und Halbach and LeitgebelT that nickel and its oxide are miscible in all proportions at 1600°C, but this report is discredited by observations of others. The melting point of NiO according to von Wartenberg and ReuschV s 1990°C. Approximate values of oxygen solubility at several temperatures were reported by Hensel and Sc0tt.O The data of Krupowski and Balickil0 are inconsistent with those of Hensel and Scott and indicate a solubility less than half that found in the present study. For oxygen solubility in Fe-Ni alloys under pure iron oxide-nickel oxide slags, only the scattered data of von Bohlen und Halbach and LeitgebelT are avail- able. The careful work of Bardenheuer and Brauns" involved silica-saturated slags. The equilibrium between Fe-Ni alloys and iron oxide-nickel oxide slags was studied by zur Strassenu and by Jander and Senf,u but no oxygen analyses were reported. Oxygen in Pure Nickel Apparatus and Nlethod: Samples were taken with a "Taylor sampler" from a bath of molten electrolytic nickel held under an air atmosphere in a magnesia-lined 30 lb induction furnace. Saturation of the melt with oxygen was effected partly by the addition of chemically pure black nickel oxide and partly by the air atmosphere. Samples were taken only when there was a clearly visible oxide phase present. To avoid contamination of this oxide phase, the silica-sheathed Pt—Pt-10 pct Rh thermocouples, by means of which temperatures were measured, were immersed in the melt for the minimum time consistent with accurate reading. Samples and temperature readings were taken only after the furnace had been

Jan 1, 1956

By J. C. METCALF

MORE than 80 per cent. of the iron produced in the United States and over 30 per cent. of the world&apos;s annual production is obtained in the Lake Superior district. Though iron ore was discovered on the Marquette range in 1844, the poor transportation facilities retarded the development of this region for many years. The structure of the Lake Superior basin is essentially an east-west synclinorium with steep dips on the south side of the lake and considerably flatter ones on the north and west. The Upper Huronian series, which -is the iron-bearing one of the formation, on the south side of the lake dips north from 55&apos; to 80°, and on the north side dips south from 8" to 200. The series has been subjected to local folding and faulting, which have influenced the development of the mining systems used.

Jan 1, 1921

By Klaus Schwerdtfeger

Activities of lead in Pt-Pb and Pd-Pb melts in the temperature range of 800° to 1200°C have been detev-mined from electromotive-. force measurements 202th the cells Both systems display strong negative deviations from Raoult&apos;s law. The data obtained with cell [1] were combined with available data on the activity of PbO in silica-satuvaterl PbO-SbO2 melts to calculate the standard free cnergy of formation 01- liquid PbO. FREE energies of formation of oxides and activities of components in metal and oxide melts can be determined with galvanic cells consisting of a metal phase, an electrolyte containing the oxide of one of the components of the metal phase, and an oxygen electrode. This technique has been used previously to measure the standard free energy of formation of solid sio2, 1 and activities in Fe-si, CO-si,2 Ni-Si,2 and CaO-P2O5 3 melts. The present paper reports activities in Pt-Pb and Pd-Pb melts as measured with the same experimental technique. EXPERIMENTAL METHOD General Considerations. The following cells were used: Pbl (PbO-SiO2)liquid, SiO2 Pt-Pb 1 (PbO-SiOz)liquid, SiO2solidO2 [2] Pd-Pb (PbO-SiOz)liquid, SiO2solid O2 [3] Liquid alloy and&apos; oxide melt were contained together in a silica glass crucible of essentially the same design as described previously.1&apos;2 The PbO-SiO2 melts are ionic conductors.&apos; During the experiment, the silica glass crystalizes in a layer adjacent to the electrolyte. The electrolyte equilibrates with solid silica and hence attains the composition of the Si02-liquidus curve in the system PbO-SiO2 at any particular temperature. Molybdenum wires were used to establish contact with the liquid metal. The oxygen electrode, which reaches the surface of the PbO-SiO, electrolyte from above, consists of a platinum wire inserted into a ceramic tube and provided with a 2-mm-diam platinum bead at its end. Gas of known oxygen partial pressure (pure oxygen of 1 atm: air, or N2 with 1.04 pct 0,) is blown through the ceramic tube onto the surface of the electrolyte. The cell reaction is Pb (metal) + 1/2O2 (gas) = PbO (electrolyte) [4] No oxidation of platinum or palladium ("displacement reaction") occurs. This is to be expected from the noble character of platinum and palladium, but was also shown experimentally, as described in the next section. The galvanic electromotive force of the cell is given by where AG is the change in free energy for Reaction [4], E(=2) is the number of electrical equivalents necessary to form 1 mole of PbO, and F is the Faraday constant. Formula [5] is valid only if no junction potential exists within the electrolyte. Junction potentials occur only when the compositions of the electrolyte are markedly different at the electrodes. Such differences are negligible in the PbO-SiO, electrolyte, as shown in the next section. Since molybdenum contact leads are used, appropriate corrections were made on the measured electromotive forces to account for the thermoelectric effect of the Mo-Pt couple. The thermoelec-tromotive forces were measured separately with a Mo-Pt couple, and were found to vary linearly from 19 mv at 740°C to 40 mv at 1310°C with molybdenum being positive and platinum negative (cold junction at 25°C). Extrapolation of these values to higher temperatures yields values which are in satisfactory agreement with those obtained previously in the temperature range 1440° to 1630°c.1,2 The change in free energy for Reaction [4] is expressed as where chemical potentials of the species. The value of constant for a given temperature because the slag composition is fixed. Inserting [6] into [5] and using appropriate expressions for upb and uO2 the relation

Jan 1, 1967

By R. P. Smith

Iron-carbon alloys containing a single-phase austenite region and a two-phase azcstenite + cementite region at the desired temperature were prepared by partial carburization of iron or partial decarburization of carburized iron. Each sample was held at a fixed temperature until equilibrium was achieved. Analysis of the austenite for carbon then gave the solubility of cementite in austenite. Solubility measzcrements were made for the temperature range 734° to 1012°C. These values together with other data give 7560 cal for the mean heat of solution of cementite in austenite, and 0.765 pct C for the eutectoid composition of austenite. They also indicate that graphite is the stable phase at all temperatures between the eutectoid and eutectic temperature. Measurements of the solubility of cementite in austenite at 927oand 1011 "C, using a method based on the equilibration of iron with boro-cementites, are reported. The solubility of cementite in austenite (?-iron) has been computed by Darken and Gurry1 from the observed solubility of graphite in austenite, and the thermodynamic properties of pure iron and of iron-carbon alloys. They have shown that the solubility of cementite is greater than that of graphite in the temperature range between the eutectoid and eutectic, and thus that cementite is metastable with respect to graphite and austenite saturated therewith. Since their computation is not in accord with the earlier experimental work of Mehl and wells,&apos; the present direct determination of the solubility of cementite in austenite was undertaken. EXPERIMENTAL PROCEDURE Each iron rod about 1/2 in. O.D. by 4 in. was first carburized at a temperature and with a H2-CH4 gas mixture such that the carbon content would be greater than that corresponding to the solubility of cementite in austenite at the desired (lower) temperature; sufficient carburizing time was allowed that the carbon content became substantially uniform, as illustrated by Curve A, Fig. 1. The sample was then partially decarburized with a hydrogen-water vapor mixture, giving a carbon distribution as schematically illustrated by Curve B. The sample was then held in a helium atmosphere at the temperature at which the solubility was to be determined until the decarburized portion of the sample came to equilibrium with that containing cementite. Curve C of Fig. 1 represents schematically the final carbon distribution; the horizontal portion corresponds to the carbon content of austenite saturated with cementite. To bring the sample to room temperature without change in the carbon distribution and in machinable condition, it was first quenched in a salt pot at 480°C, then in water at room temperature. Successive layers were machined from the center 2 in. of the sample and analyzed for carbon by the usual

Jan 1, 1960