Search Documents

[The following discussion, comprising both remarks made at the Chicago meeting and contributions since forwarded to the Secretary, is based upon the following papers, presented at that meeting : "Segregation and its Consequences in Ingots of Steel and Iron," by Alexandre Pourcel, Paris, France. (See p. 105, mans. xxii.) " Microscopic Metallography," by F. Osmond, Paris, France. (See p. 243, Trans. xxii.) " Microstructure of Ingot-Iron in Cast Ingots," by Prof. A. Martens, Berlin, Germany. (See p. 37.) " Microstructure of Steel," by Albert Sauveur, South Chicago, Ill. (See p. -546, Trans. xxii.) "Farther Observations on the Relations Between the Chemical Constitution and Physical Character of Steel," by William R. Webster, Philadelphia, Pa. (See p. 113.) "The Heat-treatment of Steel," by H. M. Howe, Boston. Mass. (See p. 466.) Since all these papers were considered together, no attempt has been made to separate the discussion strictly under the several heads.] William R. Webster, Philadelphia, Pa.: I desire to say that in my first paper (Trans., xxi., 766) the actual ultimates were subtracted from the estimated ultimates, whereas in the paper submitted at this meeting the estimated ultimates are subtracted from the actual, thus giving contrary signs. The latter method corresponds with the direct effect. of low and high finishing-temperatures ; that is, a plus difference indicates low, and a minus difference high, finishing-temperature. I make this explanation to prevent confusion in comparing the two papers. Mr. Sauveur has shown that there is a close relation between the size of the grain and the ultimate strength, and also that the size of the grain depends on the temperature at which the material is finished in rolling, and on the chemical composition of the steel. I have shown that there is a close relation between the chemical

Jan 1, 1894

By R. A. Graham, R. W. Rohde

The effect of hydrostatic pressure upon the austenite start temperature of a commercial Fe-28.4 at. pct Ni-0.5 at. pct C alloy has been determined. For pressures to 20 kbar, the austenite start temperature decreased from its atmospheric pressure value of 380°C at the rate of about 4°C per kbar. These data are analyzed by two different thermodynamic approaches; first, considering the transformation as an isothermal process, and second, considering the transformation as an isentropic process. It was found that both these approaches fit the experimental data equally well. The effect of hydrostatic pressure upon the austenite start temperature is best described by considering the mechanical work done during the transformation as that work obtained by multiplying the applied pressure with the gross volume change of the transformation. It is widely recognized1 that strain has an important effect on the initiation of martensitic transformations.* For example, the martensite start tempera- *In this paper, use of the term martensitic transformation implies the reversal of martensite to austenite as wen as the formation of martensite from austenite. ture, M,, may be increased by plastic deformation. Similarly, plastic deformation is observed to lower the austenite start temperature, A,. The effect of uniaxial stress on the M, of iron-nickel alloys has been studied by Kulin, Cohen, and Averbach.2 They found that the martensite start temperature was significantly changed by stresses well within the elastic region. Moreover, the effect of tensile and compres-sive stresses differed. These effects were explained in terms of the interaction of the applied stress with both the dilational and shear components of the transformation strain. The magnitudes of the influence of uniaxial tension, compression and hydrostatic pressure on Ms were measured in 30 pct Ni 70 pct Fe by Pate1 and Cohen.3 Their thermodynamic calculations and similar calculations by Fisher and Turnbull4 predicted the experimental results when the transformation was assumed to occur isothermally at some fixed driving force. This driving force was assumed to be supplied by a combination of the chemical free energy difference between the austenitic and martensitic phases and the work performed during transformation by the applied stress. More recently, Russell and winchel15 reported the effect of rapidly applied shear stress on the reversal of martensite to austenite in iron-nickel-carbon alloys. They performed a thermodynamic analysis of this transformation based upon the assumption that the re- versal occurred adiabatically. They concluded that the applied shear stress did not significantly interact with the transformation strain and thus did not assist in inducing the reversal. Rather they concluded that the reversal was effected by localized strain heating which resulted from the gross local shear deformation of the experiment. In either the adiabatic or isothermal analysis it is necessary to compute the work performed by the interaction of the applied stress and the transformation strains. In the case of hydrostatic pressure this interaction has been treated by two different methods. In either case the applied pressure is assumed to remain constant during the transformation. In one treatment the applied pressure is assumed to interact directly with the dilatational strain associated with the formation of an individual martensite plate.3'4 This local strain has been measured at atmospheric pressure in iron-nickel alloys by Machlin and Cohen.6 In the above treatment this local strain is assumed invariant with temperature and pressure changes. In the other treatment the applied pressure is assumed to interact with the gross volume change of the transformation.7,8 The usefulness of this latter treatment has been demonstrated by Kaufman, Leyenaar, and Harvey7 who calculated the effects of pressure upon the martensite and austenite start temperatures of Fe-10 at. pct Ni and Fe-25 at. pct Ni alloys. Excellent agreement was obtained between their calculations and their experimental data on an Fe-9.5 at. pct Ni alloy. However, this treatment suffers from the fact that the data required to calculate the volume change of the transformation (i.e., the initial specific volumes, the thermal expansion and compressibility data for both the austenitic and martensitic phases) is, in general, not available for any material except pure iron. Thus the calculations of Kaufman et al.7 were necessarily performed by assuming that the volume change of the martensitic transformation in the iron-nickel alloys was that same volume change occurring during the a-? transformation in pure iron. While this approximation may suffice for very dilute alloys it is likely to be inaccurate in high nickel alloys. We have performed measurements of the effect of hydrostatic pressure to 20 kbar on the A, temperature of an Fe-28.4 at. pct Ni-0.5 at. pct C alloy. The composition is similar to the alloy used by Pate1 and Cohen3 to determine the effect of pressure upon the M, temperature. The present measurements permit calculation of the interaction between the applied pressure and the transformation strain. Additionally, measurements have been made which allow precise determination of the gross volume change of the transformation. The data allow direct comparison between the alternate hypotheses of the interaction between the applied pressure and a dilatational transformation strain characterized by either the formation

Jan 1, 1970

By Morton Macartney

FOR many years the developers or owners of worthy mining ventures in need of financing have found it almost impossible to obtain such financing under the conditions existing in most other lines of business. High rates of interest and unfair participation in profits have robbed the developers of much of their holdings, and have resulted in over-capitalization and many other like evils. When the general financial condition of the country is bad, this difficulty increases to a point where many operations must cease and hen are thrown out of employment. In 1.934 this situation had developed to such a point that Congress attempted to aid the mining industry. It first authorized the RFC to make loans to recognized and established corporations, individuals, and partnerships engaged in the business of mining, milling, or smelting of ores in June, 1934, limiting such authority to loans adequately secured, the security to consist of mineral acreage. The requirements of the law were stringent and of the 252 requests for loans received up to June 1, 1935, 35 were authorized.

Jan 1, 1936

By Anthony Anable

HOOVER DAM, rapidly nearing completion in the Black Canyon of the Colorado River at Boulder City, Nev., taxes the superlatives of the vocabulary to describe. For by all odds, it is the largest construction project of its type ever essayed by man and the plants providing the essential materials of construction are also in a class by themselves not only in size but in advanced design, mechanization, and accurate control. Picture, if you will, the great aggregate plant, as it is called, situated about 4 mi. upstream from the site of

Jan 1, 1934

By John E. Young

U.S. Steel Corp.'s Winifrede mine is operated by Lynch District in the mountainous region of eastern Kentucky. This region is characterized by narrow finger ridges and precipitous slopes, which present both an opportunity and challenge in the design and selection of coal-handling facilities for the movement of coal from the section belts to the railrod cars. Lynch District selected diesel-powered locomo¬tives and 100-ton articulated cars capable of negotiating sharp curves. The drop¬bottom mine cars are equipped with longitudinally hinged doors that are auto¬matically opened and closed. Lynch District selected a large-diameter steel-lined borehole for lowering the coal approximately 1000 ft from the seam level to the valley floor railroad load-out point. Taking advantage of gravity, the presized coal is "lowered" vertically approximately 720 ft to existing entries of a previously abandoned mine. The coal is then conveyed horizontally into storage. The coal¬handling facility from the mine-car dump to the railroad load-out point is fully automatic through use of tone control. TV cameras are installed along the facility to continuously monitor the strategic points. The diesel locomotives are either directly operated or remotely radio-controlled, depending on the functions Per¬formed. U.S. Steel Corp.'s Winifrede mine is operated by Lynch District in the mountainous region of eastern Kentucky. This region is characterized by narrow mountain ridges and precipitous slopes which present both an opportunity and challenge in the design and selection of coal-handling facilities for the movement of coal from the section belts to the railroad cars. The narrow finger ridges precluded use of under¬ground haulage and, thereby, presented the opportunity to use high-capacity equipment on the outside bench. The precipitous mountain slopes, steepest at the Wini¬frede seam horizon, presented a challenge to select a solution for lowering the coal approximately 1000 ft from the seam level to the valley floor railroad load-out point. It was evident from the start of planning that these two factors predominated; namely, rail haulage and coal lowering, and solutions to these would determine the final design of the Winifrede mine coal-handling facilities. The Winifrede mine derives its name from the Wini¬frede Seam which comprises the total reserve recov¬erable from this facility. The seam is 5 ft high with a good siltstone bottom and competent shale or sandstone roof. The seam is at an elevation of 2700 ft where the mountain ridges are long and narrow. This configuration of the reserve was ideal for conveyor belt installation to transport the coal from the working face to the outside bench. The preclusion of underground rail haul¬age permitted an opportunity to review the type of locomotive power and to select high-capacity equipment without the limitations associated with underground systems. Since the basic electrical design of the mine was al¬ternating current, with rectification to direct current for shuttle cars required only in the face areas, there was no point in bearing the burden of additional cost of dc trolley installation. And, since the haulage would re¬quire only a few tunnels to negotiate sharp points and to reach the back side of the reserves, diesel power was selected for the haulage locomotives. To provide stability on the almost continuously curv¬ing track and to provide the maximum width of haul¬age equipment, both locomotives and mine cars, stan¬dard railroad gage was chosen to offer the largest choice of equipment. The decision was made to select a standard 45-ton railroad diesel locomotive but to lower the cab height to reduce tunnel excavation requirements. The mine car was the next challenge. Past experience in Lynch operations indicated that drop-bottom cars would be a successful application with the free-flowing coal. The search was for a drop-bottom car within the dimensions of the locomotive to discharge the coal in the shortest time. Numerous types were considered and visits made to various sites to observe cars in operation.

Jan 1, 1972

By ROBERT E. CROCKETT

MAGNETITE mining and milling in New York, New Jersey and Pennsylvania continued to remain comparatively inactive during 1933, owing to the low rate of output of the steel industry and also to unrestricted importation of foreign ores. However, some improvement over conditions existing in 1932 was noticeable, particularly in New Jersey, where one plant, that of the Washington mine of the Alan Wood Mining Co., at Oxford, went on full production in August. At Lyon Mountain, N. Y., the Chateaugay Ore and Iron Co. resumed mining and milling operations in October, on a reduced scale, principally to provide employment during the winter months. The Chateaugay company produces a special low-phosphorus pig iron. During the year they obtained a contract to supply their product for use in the manufacture of the suspension cables of the New. Golden Gate Bridge.

Jan 1, 1934

By K. G. Wikle, J. G. Klein, W. W. Beaver

Consolidation of hydride process, electrolytic, calcium reduced, and comminuted thorium powder, as well as saw chips and lathe turnings, by vacuum hot pressing and by cold pressing-vacuum sintering was studied. The mechanical properties of the consolidated material in the extruded form are compared with those of wrought castings. AT present there little little industrial use for thorium metal, although it has some important though small scale applications in electronic equipment. Despite its high inelting point—about 1750°C —a low modulus of elasticity, 11.4xl0 si at 20°C;' relatively low mechanical properties coupled with a high density, 11.7 g per cu cm; and an unusually high chemical activity with normal atmospheres limit any structural applications. The metal is utilized as an alloying element principally in magnesium. Pure thorium finds utility as electrodes in gaseous discharge lamps such as the high intensity mercury lamp' because its low work function and high electron emissivity provide lower starting potentials and more uniform operating characteristics than other available materials. The metal is also found in photoelectric tubes used for the measurement of the ultraviolet spectrum." Thorium metal has been used in germicidal lamps of the cold cathode type as sputtered coatings on nickel in order to provide a low work function surface and a low starting voltage. Other applications have involved the radioactive properties of thorium for the production of ionized particles." The potential value of thorium is much greater than its present use pattern because of possible utility in the field of nuclear power. Th may be converted through nuclear reaction to a fissionable element U which should be capable of acting similarly to U in the g'eneration of atomic power. Thorium has been reported to be about three times as plentiful as uranium in the earth's crust, placing it in the order of abundance of lead and molybdenum." Thus, it is of interest in augmenting the potential supply of fissionable material for nuclear power. Because of its high melting point, thorium is usually produced as a powder through the calcium reduction of its oxide or thermal reduction of halides by sodium, magnesium, and calcium. It may also be produced in flake form by electrolysis of fused alkali or alkaline earth chloricles and fluorides. Therefore, powder metallurgy assumes importance in the fab- rication of thorium metal shapes. Furthermore, it is rather difficult to obtain pure thorium by melting, as the molten metal reacts readily with graphite as well as oxide, carbide, and nitride refractories. These contaminate the melt with oxides, carbides, and metallic impurities." The current investigation was undertaken to examine the fabrication of thorium by powder metallurgy methods which have been used for the commercial production of beryllium and other metals.' A sparcity of data concerning the comparative cold and hot compaction of thorium powders of different derivation existed. Therefore, all commercially available types were examined along with other experimentally produced thorium powders in order to round out the comparison of consolidated thorium powders with melted reguline metal. Review of the Literature By heating a mixture of ThC1, with potassium, Berzelius made the first thorium metal as an impure powder in 1828. Improvements in the basic process, increasing thorium assay to 99 pct, were made by several investigators including Arsem," Lely and Hamberger10 and Von Bolton." Calcium reduction of Tho, to make powders was investigated by Berger," Huppertz,'" Kroll," and Kuzel and Wedekind.'" A thorium powder produced by this method using a CaC1, fluxing agent assayed 99.7 pct, as reported by Marden and Rentschler.'" Compacted and sintered, this product was found to be ductile, and could be fabricated into wire and sheet. Improvements of the calcium reduction process were made later" wherein CaCl, was eliminated from the reaction, producing metal assaying 99.8 pct Th. Further work by Lilliendah118 howed that a coarser metal could be obtained by the substitution of ThC1, or ThOC1, for oxide with consequent advantage of stability to atmospheric reaction. Reports on the technology of thorium developed in Germany during World War II have been made by Espe."' Thorium powder of 99.5 pct Th was obtained by reduction of the oxide by calcium. Screening to —200 mesh, compacting with about 20 tsi, and sintering in vacuo at 1320" to 1360°C for 3 hr resulted in a porous sinter cake. The sinter cake was sufficiently ductile to be worked into bar, wire, and sheet which could be employed as electrode materials.

Jan 1, 1957

By D. T. Peters

To better understand the Co-Mo interaction in maraging steels, the precipitate reversion behavior of two alloys closely related to the 18 Ni-250 grade has been studied. The reversion experiment is carried out by aging at a low temperature, T1 (preaging temperature), for some period of time and then aging at a higher temperature, T2, called the reversion tetnperature. Aging and reversion tmzperatures used were in the range 679 to 1050°F. Reversion is marked by an increase in resistivity and a decrease in hardness. It teas found that some reversion took place at all cornbinations of T1 and T2 but that pronounced rei3ersion resulfed for an Fe-18 pct Ni-5 pct Mo-8 pcl Co alloy exposed to preagz'ng' temperatures at or below 850°F. A similar alloy not containing cobalt exhibited no such discontinuity in reversion behazior with TI. The results are interpreted in terms of two types of molybdenum-rich precipitates, one nucleated at dislocations and the other in the matrix. The increased supersaturation resulting from the presence oj- cobalt evidently provides sufficient energy to nucleate the matrix phase. Anotnalies in the temperature dependence of the resistivity decrease and peak hurdness in the Fe-18 pct Ni-5 pct Mo-8 pct Co alloy as a junction of aging temperature noted in an earlier study are explained on this basis. SEVERAL investigatorsl-9 have studied the details of the precipitation-hardening reaction of the maraging steels. The great majority of conclusions have been drawn from transmission electron microscopy. Although much has been learned by this method, alternate techniques which will give information earlier in the aging process are needed for a more complete understanding of the series of precipitation steps probably involved in the aging reaction. Peters and cupp'' have recently shown, by measurements of the kinetics of precipitation, that an 18 pct Ni-Co-Mo maraging steel shows a distinct change in precipitation behavior at aging temperatures below 850°F. The results were interpreted in terms of the existence of two types of precipitates at low aging temperatures. Only one precipitate type is present at higher aging temperatures. The low-temperature precipitate was found to be a particularly effective strengthener. No evidence for the additional low-temperature precipitate was found in the 18 pct Ni-5 pct Mo ternary alloy. The object of this investigation was to study further the characteristics of the two types of precipitates and the interaction between cobalt and molybdenum characterizing this system. Some preliminary experiments indicated a difference in reversion behavior in specimens aged above and below 850°F. This suggested that knowledge of the reversion behavior might shed some light on these two questions. Hardy and Heal11 have defined reversion as the loss of hardness, electrical conductivity, or other properties caused by heating for a very short time at temperatures above the aging temperature. The precipitate reversion referred to in this paper is entirely distinct from "austenite reversion" often referred to in maraging steel literature. This latter phenomenon could more accurately be called the diffusion-controlled formation of austenite. Much has been written about reversion in several of the aluminum-base binary and ternary alloys.'2-16 Two explanations for reversion have been advanced. Based on the classical nucleation theory of Volmer-Weber-Becker-Doring,17 Konobeevski18 suggested that reversion was due to the size of the precipitate particles

Jan 1, 1968

By W. A. Oates, J. A. Lambert, P. T. GaIIagher

Monte Carlo methods have been used to compute the arrangements of interstitial atoms dissolved in tetrahedral sites in bcc lattices. It is assumed that the presence of an interstitial atom "blocks " a certain number of neighboring sites and prevents their occupancy. Sites "blocked" by more than one filled site are allowed for. The computed values of. the mean occupation number (defined as the ratio of the total number of sites blocked to the number of solute atoms are used to calculate the configurational entropies of the solutions. These entropies are compared with those resulting from previous theoretical studies of this problem and also with available experin~ental data for the p Zr-H, Nb-H, V-H, and Ta-H systems. Evidence is also given that the "blocking" explanation of low limiting compositions in these systems, rather than this being due to initial limitations on the number of sites available, is probably correct. THE ideal partial configurational entropy of mixing of an interstitial solute in a metal is given by: where p is the number of interstitial sites per metal atom and Xi is the atomic fraction of the interstitial. For the bcc lattice. which we shall be concerned with in this paper, the interstitial positions are shown in Fig. 1. It can be seen that for the tetrahedral sites, p=6. whereas for the octahedral sites, p = 3. Different emphasis has been placed on the relative importance of energy and entropy effects in determining deviations from ideality in interstitial solid solutions. In some cases the same system, e.g., Fe-C, has been described by the contradictory regular and athermal solution models indicating that the enthalpy and entropy functions, derived from equilibrium data, are frequently not accu.rate enough to differentiate between these treatments. However, for certain metal-hydrogen solutions the equilibrium data is available over sufficiently wide ranges of temperature and composition to permit a reasonably accurate determination of the compositional variation of the heats and entropies. Hoch&apos; has attempted to interpret the results of interstitial solid solutions in terms of a regular solution model. In the case of the Ta-H system where 13 = 6, this model entails fitting the experimental relative partial entropies of solution, asH, to the equation: where ASgs is the relative partial excess entropy of solution of hydrogen. Hoch found that the results of Mallett and Koeh1 could be fitted to this equation with an approximately constant value of AF up to XH = 0.25. However, it is apparent from the solubility isotherms in this system which become asymptotic to the composition TaH that, since (Xh /6 - ~Xh ) becomes infinite only at TaH6, it is necessary that AS<&apos; tends to infinity at TaH. In other words, the low saturation composition of TaH, instead of the anticipated TaH,, eliminates the possibility of applying regular solution theory to such systems. Rather large negative excess configurational entropies must exist at higher hydrogen concentrations in order to explain the lower saturation values. To account for these low limiting compositions and excess entropies two distinctly different approaches have been followed. Rees and many others1-l2 have assumed that not all interstitial sites are crystallographically equivalent with respect to the interstitial addition; that is, in Eq. [I] p is less than the value anticipated from geometrical considerations. To describe, say, a bcc metal-hydrogen system with a limiting composition of MH by this approach one would consider that p = 1 in the first instance instead of p = 6.&apos;j3 In some cases, nonintegral values of B have been taken in order to improve the fit with the experimental data over limited ranges of composition. The other approach which has been used to explain the low saturation compositions is to assume that, although all sites are available for occupancy, strong repulsive interactions exist between the neighboring interstitial atoms, and hence occupancy of any site excludes or blocks a certain number of neighboring sites from being occupied. Earliest treatments of this concept considered the exclusion of an integral number, of nearest-neighbor sites from being occupied at all concentrations. In this case, the partial configurational entropy is given by: These early treatments failed to allow for the overlap of the blocked sites which will arise at all but the very lowest concentrations. More recently attempts have been made to calculate the effect of this decrease in the number of blocked sites on the configurational entropy. Using the quasichemical treatment of interstitial solid solutions as given by Lacher and assuming that an infinite repulsive interaction energy existed between the solute atoms. atom obtained an approximate configurational entropy applicable to the blocking with overlap case:

Jan 1, 1970

By P. V. Faragher

A METAL or alloy finds its place in commerce in proportion to its ability to serve certain purposes better and more economically than other materials. While there is some overlapping of the fields of application of the various metals under discussion in this symposium, each one has its uses for which it is especially adapted. While aluminum is the most recent of the metals to enter the field, the development of the industry has been based on its peculiar properties, by virtue of which new uses for non-ferrous metals have been created. There has been substitution of this new metal for other members of the group but there has been a far greater development in entirely new fields. In common with the other non-ferrous metals, aluminum is resistant to atmospheric corrosion. It also withstands the action of many of the common chemical reagents, strongly alkaline substances being the notable exceptions. The outstanding properties on which the application of aluminum is based are its low specific gravity and its ease of fabrication into the forms in which it is used. It is noteworthy that this property of specific lightness is retained in all the commercial aluminum-base alloys. This statement does not apply to aluminum bronze; this is more properly a copper-base alloy, since aluminum enters into its composition to the extent of only about 10 per cent. None of the commercial casting alloys of aluminum has a density exceeding that of the parent metal by more than about 10 per cent., and some are actually lighter. In the so-called "strong alloys" of aluminum in which strengths comparable to that of mild steel are developed by heat treatment, the greatest increase in density is only slightly more than 3 per cent., and one of these, also, is lighter than aluminum. This property of lightness combined with the desirable mechanical properties of the alloys, makes aluminum especially suited for parts of moving assemblies where saving in power, as well as a decrease in stresses resulting from inertia and vibration, are of importance.

Jan 1, 1928

By Donald H. McLaughlin

THE activity and enthusiasm of pioneers still prevail among workers in applied geophysics1.- Within the year, new devices have .been tried out, instruments and technique have been improved and the methods of application to commercial problems have been increased in many ingenious ways. There is still great need for more skillful interpretation of results in terms of geology, but oil the whole geophysical prospecting is making encouraging progress toward finding its proper place and function in engineering and geological practice. Spectacular successes continue to be reported, particularly .from the Gulf Coast, where the race for salt domes has not slackened, and encouraging results have been giined elsewhere in the mapping of structures in the search for oil. In the mining field, however, it can hardly be claimed that the same measure of success has been obtained, for brilliant efforts worthy of wide recognition have been overshadowed to some eatent by the unfortunate outcome of surveys undertaken unwisely without recognition of the limitations of the work. Consequently, hopes were aroused that could not be fulfilled, and it must be admitted in an impartial survey that there are a few regions, chiefly in the far north, where the standing of geophysical prospecting is somewhat doubtful and where the course of public opinion regarding it shows a certain similarity to the history of the market during the past few months. Reliable work, however, is steadily going 011 and it can confidently be expected that the methods will eventually be regarded in many regions as an essential part of the technique of securing geologic data needed for intelligent exploration.

Jan 1, 1930

By C. W. Vaupell

The Huitzuco mines lie in north central Guerrero, Mexico; production has been about 90,000 flasks of quicksilver since 1873. Near-surface ores fill extinct mud geysers and the deep deposits are chambered veins, stock-works in brecciated blocks, and replacements in limestone. The epigenetic minerals livingstonite, stibnite and sulphur occur in limestone, gypsum and dolomite through a developed vertical range of 260 meters. The deepest workings expose an increased amount of stibnite, which probably indicates that the lower limit of mercury mineralization is being approached. A resurgence of heat and water formed geysers over an extended area after the period of mercury mineralization. Mud geysers, which are situated, in the outcrops, contain the secondary mercury minerals, cinnabar and barccnite in the gravel and mud filling the vents. A 150-ton flotation plant is in operation concentrating stope fills that assay 3.0 kg. of mercury per ton. In one open stope, which is more than one hectare in area and 60 m. high, 150,000 tons are available. Introduction The Huitzuco mercury mines are of interest because of the unusual occurrence of ore in extinct geyser vents and the presence of several rare mercury minerals. Some of the deposits have typical characteristics of the telethermal zone and there is a gradation towards typical epithermal mineralization in depth. Halse,1 Villarel1o,2 Mactear3 and Merri114 have described the geology and the early operations in the district, and Bar-cena5 and Mallet6 have described the rare mercury minerals, livingstonite and barcenite, found at Huitzuco. Location The village of Huitzuco lies in the north central part of the State of (Guerrero, Mexico, 27 km. (16.7 miles) east of Iguala, which is the largest and most important town in the area. Iguala is served by the Mexican National Railways and also by the Mexico City-Acapulco highway. The highway is surfaced from Mexico City to Iguala, a distance of 200 km. (124 miles) by road, and there is a fairly good, level, dirt road from Iguala to Huitzuco. The elevation above sea level is about 1000 m. (3280 ft.). The climate is warm and very dry except during the rainy season, from June to

Jan 1, 1941

By C. W. Vaupell

The Huitzuco mines lie in north central Guerrero, Mexico; production has been about 90,000 flasks of quicksilver since 1873. Near-surface ores fill extinct mud geysers and the deep deposits are chambered veins, stock-works in brecciated blocks, and replacements in limestone. The epigenetic minerals livingstonite, stibnite and sulphur occur in limestone, gypsum and dolomite through a developed vertical range of 260 meters. The deepest workings expose an increased amount of stibnite, which probably indicates that the lower limit of mercury mineralization is being approached. A resurgence of heat and water formed geysers over an extended area after the period of mercury mineralization. Mud geysers, which are situated, in the outcrops, contain the secondary mercury minerals, cinnabar and barccnite in the gravel and mud filling the vents. A 150-ton flotation plant is in operation concentrating stope fills that assay 3.0 kg. of mercury per ton. In one open stope, which is more than one hectare in area and 60 m. high, 150,000 tons are available. Introduction The Huitzuco mercury mines are of interest because of the unusual occurrence of ore in extinct geyser vents and the presence of several rare mercury minerals. Some of the deposits have typical characteristics of the telethermal zone and there is a gradation towards typical epithermal mineralization in depth. Halse,1 Villarel1o,2 Mactear3 and Merri114 have described the geology and the early operations in the district, and Bar-cena5 and Mallet6 have described the rare mercury minerals, livingstonite and barcenite, found at Huitzuco. Location The village of Huitzuco lies in the north central part of the State of (Guerrero, Mexico, 27 km. (16.7 miles) east of Iguala, which is the largest and most important town in the area. Iguala is served by the Mexican National Railways and also by the Mexico City-Acapulco highway. The highway is surfaced from Mexico City to Iguala, a distance of 200 km. (124 miles) by road, and there is a fairly good, level, dirt road from Iguala to Huitzuco. The elevation above sea level is about 1000 m. (3280 ft.). The climate is warm and very dry except during the rainy season, from June to

Jan 1, 1941

By J. Th. G. Overbeek, R. Schumann, P. L. De Bruyn

THE technique of concentrating valuable minerals from lean ores by flotation depends upon the creation of a finite contact angle at the three-phase contact, mineral-water-air. If the mineral is completely wetted by the water phase, contact angle zero, there is no tendency for air bubbles to attach themselves to the mineral. However, when the contact angle is finite, the surface free energy of the system, water-air bubble-mineral particle, can be diminished by contact between the bubble and the particle, and if not too heavy the mineral will be levitated in the froth. With a few exceptions, all clean minerals are completely wetted by pure water. Thus the art of flotation consists in adding substances to the water to make a finite contact angle with the mineral to be floated, but to leave the other minerals with a zero contact angle. The contact angle concept and experimental measurements of contact angles have played important roles in flotation research for several decades.1-3 Nevertheless, there remain unanswered some basic questions as to the scientific significance of the contact angle and the nature of the processes by which flotation reagents affect contact angles.

Jan 5, 1954

By M. R. Tek, K. H. Coats, D. L. Katz

A large number of boundary value problems encountcred in unsteady-state heat transfer, fluid flow through porous media, neutron diffusion and mass transfer involve the solution of a linear, parabolic partial differential equation commonly refcrred to as the diffusivity equation, where U is the dependent potential variable. K is the diffusivity (hydraulic, thermal, neutron, etc.) and 1 is the time variablc. Solutions to Eq. I are available in the literature for a wide variety of initial and houndary conditions. The great majority of these solutions are ohtained for geometric boundaries corresponding to linear. cylindrical or spherical flow models. A typical engineering application where the solution to Eq. 1 is required is the calculation of underground water encroachment across the boundaries of oil or natural gas reservoirs, In this particular area of application, the reservoir boundary is invariably approximated by circular geometry. However. the areal shape of many reservoirs can be better approximated by elliptic rather than circular boundaries. Thus the need for a general method of solving the diffusivity equation in elliptic coordinates arises in this problem as well as in other engineering applications involving elliptic boundaries. The solution to the diffusivity equation usually in volves the Error Function for the linear flow model, Bessel functions for the radial flow model and trigonometric or Legendre functions for the spherical flow model. It is well known that the general solution to the diffusivity equation in elliptic coordinates involves Mathieu functions. The significance of Mathieu functions in the analytical treatment of the diffusivity equation in elliptic coordinates is discussed in the literature However, these references do not providc analytical solutions useful in practical engineering problems. The objectives of this papcr are the development of the equations describing the unsteady-state liquid flow through a porous medium with an elliptic inner boun- dary, the development of a numerical method of solving these equations and, finally, a comparison of the water encroachment quantities calculated from the elliptic flow equation with those calculated from the radial flow equation. While the specific problem treated in this paper relates to unsteady-state liquid flow through a porous medium, the basic equations and computational techniques devcloped will apply equally well to problems occurring in the other areas of engincering interest mentioned previously. The solution given here is limited to a single case in which thc outer boundary encloses an area 100 times that of the inner boundary. DESCRIPTION OF THE FLOW MODEL Fig. 1 shows the flow model upon which the calcu lations presented in this paper are based. The inncr and outer houndaries of the flow model are represented by two confocal ellipses with major and minor axes, respectively, equal to 2a1, 2b1, and 2a, and 26,. The height of the elliptic cylinder flow model is denoted by 17. The following assumptions are employed in the development 01 the equations governing the unsteady-state liquid flow through the described flow model. 1. Uniform porosity and permeability throughout the flow model

Discussion of the paper of John H. Hall, presented at the New York. Meeting, October, 1913, and printed in Bulletin No. 79, July, 1913, pp. 1247 to 1256. WILLIAM &apos;R. WEBSTER, Philadelphia, Pa.:-I would like to call ,attention to the fact that the results of the ordinary tension and bend tests do not always give us the information we want even if we figure out the amount of work done. You want a bending test of sufficient width and full thickness. In the case of eyebars, for instance, I have had experience with a 10- by 1-in. eyebar which gave perfectly good results in a full-size test of the finished bar. The 10- by 1.5-in. and 10- by 1.75-in. eyebars from the same heats-of steel were absolutely worthless in full-size tests. The narrow bending tests from all these bars gave good results. Bat after going into the matter fully, we found that if pieces about 3 in. wide and full thickness were used for the. cold bending tests, the heavier material would not stand this test, but failed. That is, in order to check the quality of the rolled bar you should have a wide piece of full thickness for cold bending, as the narrow pieces give misleading results. J. E. JOHNSON, JR., New York, N. Y. :-I would like to ask if there have been any tests made to compare the results of Charpy tests with the true dynamic test similar .to the Wohler test, except that the piece is subjected to a tensile or compressive stress and to alternating stresses in addition, at the same time. This seems to me to approach more nearly than any other test to the conditions of actual service. where the piece is under a fixed initial stress plus a highly variable and often alternating stress. Some tests were made on this plan in England within a year or two. The test piece was Subjected to either a tensile or compressive stress of known amount and simultaneously to alternating stresses in addition. Such a. test as this gives information which we cannot get by a tensile test or even from the tensile strength multiplied by an. elongation. Such tests, however, are exceedingly tedious and require long periods of time in order to obtain valuable results. If material could be subjected to these dynamic tests and the same material to the. Charpy shock test, and if some reasonable qualitative relation could be established between the results of the two tests, then we could assume that the shock test, which is so simple and easy to make, was a measurably accurate test of the dynamic qualities of the material. At present it does not seem

Jan 12, 1913

By W. J. Kroll

Jan 1, 1960

By G. P. Marino

The "conductivity ", Kr, of a spherical void in a linear temperature gradient due to radiation is calculated by integration of the general expression for diffuse radiation between two gray surfaces of arbitrary orientation. The spherical geometry allows an exact evaluation of the phenomenon without resorting to up-proximate expressions for the radiant heat flux. The resulting expression for Kr is three quarters of the approximate value obtained by Loeb. IN the determination of the thermal conductivity of porous materials such as sintered UO2 and ThO2 fuel pellets, the magnitude of the thermal conductivity in the pores due to radiative heat transfer across the pore, Kr, may be important in assessing the total conductivity of the pellets. Loeb&apos; has calculated Kr for various pore geometries by approximating the net flux of heat between two surfaces of temperature difference AT as 4eT~AT and obtained: K,=4yoet3odp [1] where a is the Stefan-Boltzmann constant, E is the emissivity of the radiating surface, To is the average absolute temperature of the region across which radiation occurs, dp is the largest dimension of the gap in the direction of heat flow, and y is a geometric factor. That is: y = 1 for laminar pores and cylindrical pores with axes parallel to the heat flow direction, y = 2/3 for spherical pores, y = /4 for cylindrical pores with axes perpendicular to heat flow direction. It was the purpose of this work to obtain an exact expression for K, in spherical pores by integration of the general expression for the net heat transfer between two incremental areas on the surface of a spherical pore. This procedure yields a value of Kr 3/4 of that obtained by Loeb. I) CALCULATION OF Kr Fig. 1 illustrates the general geometry which defines the problem. The total emissive power for a gray body is given by: E = EoT4 [2] where E is the radiated energy per unit area of the radiation surface per unit time, T is the absolute temperature, o is the Stefan-Boltzmann constant (o = 5.67 X lo- &apos;&apos; watt per sq cm-"K1), and E is the emissivity of the surface. Although Eq. [2] gives the exact expression for the total emissive power of any gray body, all practical problems involve the net exchange of thermal radiation between a body and surrounding bodies. The two major considerations in the solution of such problems are a) shape and relative position of the surfaces and b) the emissivities of the surfaces. In this work it shall be assumed that all incremental areas on a pore have the same emissivity and, further, that little or no reflection occurs (i.e., the radiation hitting a surface is either absorbed or transmitted). Thus, the solution of the stated problem requires only that consideration a be satisfied. Consider two incremental surface areas dA 1 and dA2 of the same material in a general orientation to one another. Let dAl be at temperature TI and dAz be at T2. Fig. 2 illustrates the geometrical parameters involved. That is, 71, is the normal of dA, n2 the normal of dA2, r the line connecting the centers of each area, 81 the angle between nl and r, and Q2 the angle between 7,2 and r. Using Eq. [2] and the Lambert cosine law of diffuse radiation it is easily shown that:293 WdAf- dA, = ecr T*------^fpi------" dAidA2 [ 3a 1 and

Jan 1, 1970

By John Chipman

Published data on the equilibria of carbon in binary Fe-C austenite with H2-CH4 and CO2-CO gas mixtures are used to obtain the constants of an equation repre -senting the activity coefficient of carbon throughout the stable austenite range of temperatutre mid compositiotl. Calculated values for the solubility of graphite are found to be in agreement with the best-published direct observations. Its heat of solution is 10,680 calper g-atom. The free energy of formation of cementite is culculated from the equilibrium compositions of austenite and of gas. Its entropy and heat of formation are also obtained. BASIC knowledge of the high-temperature properties and treatment of steels is contained in the Fe-C diagram and its extensions for the effects of alloying elements. The application of thermodynamics to the Fe-C system, with addition of alloying elements, can serve to simplify and systematize this knowledge. The points of beginning are the binary fee solution, austenite, concerning which our information is reasonably complete, and the binary carbide, cementite. Further studies must include the other phases of the binary system, a and liquid, and for these an accurate knowledge of the ? phase boundaries is essential. These studies should provide a firm base for systematic study of the effects of alloying elements on all phases of the system, their transformations, and precipitation phenomena. With the aid of the simplifying thermodynamic concepts of activity coefficients and interaction parameters it is to be hoped that the results of these studies will be amenable to computer solution thus making the information on multicomponent systems more readily available than would be possible in multidimensional diagrams. Studies of the thermodynamic properties of austenite have utilized equilibrium measurements on the reactions:

Jan 1, 1968

By T. R. Cass, M. R. Achter

A technique for measuring the creep and rupture strength of nickel specimens bonded by sintered oxide layers has been developed for the investigation of the role of grain-boundary oxide in the oxidation strengthening of nickel during creep at 817 °C. Prom the inverse dependence of the rate of bonding on the thickness of the starting oxide, it is suggested that the rate of diffusion of Ni++ through NiO is the controlling process at the start of sintering. Cornparisons of the creep and rupture strength and of the microstructure of sintered couples with conventionul creep specimens suggest rupture in nickel is prevented by load-bearikzg, ikltergranular layers of oxide. A number of recent investigations have shown that at high temperature and low stress the creep-rupture strength of nickel and nickel-base alloys may be much greater in air than in an inert gas or vacuum.&apos;-7 For example, at 817°C and 2500 psi, nickep failed in vacuum in 48 hr but not in air after 4000 hr, and a Ni-Cr-A1 alloy5 at 1038°C and 3000 psi failed in vacuum in 4 hr but not in air after 731 hr. Fig. 1 is a typical creep curve in air for materials experiencing this pronounced environmental strengthening. A common feature of these curves is the entry into a third stage of accelerating creep, concurrent with the for-

Jan 1, 1962