Search Documents

By Walter Crafts, C. M. Offenhauer

In a previous study of the carbide phase of chromium steels, it was shown that chromium carbide (Cr7C3) is 2 more stable carbide than cementite (Fe3C) at tempering temperatures above about 500°C. in quenched steels containing from about I to 7.5 per cent chromium. Below this temperature the carbide phase was found to consist of cementite in all of the steels examined. In the present investigation it was found that a similar change in the carbide phase takes place in molybdenum and in chromium-molybdenum steels at approximately the same tempering temperatures. The approximate ranges of occurrence of the alloy carbides Cr7C3, Cr4C, and Mo2C have been determined in steels containing up to 5 per cent chromium, I per cent molybdenum and 0.60 per cent carbon. The experimental steels were made in small high-frequency furnaces from Armco ingot iron, low-carbon ferrochromium and calcium molybdate and were poured into 2-in. ingots, which were forged to I-in. round bars. Sections of the bars were heated to the carbide-solution temperature and cooled rapidly to induce austenite transformation at relatively low temperatures. The steels were subject to some segregation, therefore comparatively high temperatures were necessary to dissolve all of the carbides. The microstructure of the quenched specimens was examined to verify the belief that the carbides had been dissolved, and also to determine the nature of the nonmartensitic structure of incompletely hardened steels. Ferrite and pseudo-martensite were present in some of the specimens, but all specimens were quenched at such a rate that pearlite was not formed, in order to ensure the formation of the carbides at temperatures lower than about 500°C. It had been found previously1 that in chromium steels the chromium carbide could be produced by transformation of austenite in the pearlite range above 500°C., and, in order to start the tempering treatment with the carbide present as cementite, the absence of pearlite was considered to be essential. The specimens were tempered for 64 hr. to permit the formation of the stable carbide. After tempering, the specimens were submitted to microscopic and X-ray examination. The carbides were separated either electrolytically in a 5 per cent HCl electrolyte or with an acidified copper-potassium chloride solution. The crystal structure of the carbide phases was determined by the Debye-Scherrer type of X-ray patterns. The X-ray patterns obtained from specimens near the boundaries between two types of carbides were generally weak and diffuse as compared with the other patterns. For this reason, and because the more soluble components may be masked, the boundaries between the phases could not be determined precisely. However, the X-ray analysis of electrolytically separated carbides has given consistently reproducible results

Jan 1, 1943

By Walter Crafts, C. M. Offenhauer

In a previous study of the carbide phase of chromium steels, it was shown that chromium carbide (Cr7C3) is 2 more stable carbide than cementite (Fe3C) at tempering temperatures above about 500°C. in quenched steels containing from about I to 7.5 per cent chromium. Below this temperature the carbide phase was found to consist of cementite in all of the steels examined. In the present investigation it was found that a similar change in the carbide phase takes place in molybdenum and in chromium-molybdenum steels at approximately the same tempering temperatures. The approximate ranges of occurrence of the alloy carbides Cr7C3, Cr4C, and Mo2C have been determined in steels containing up to 5 per cent chromium, I per cent molybdenum and 0.60 per cent carbon. The experimental steels were made in small high-frequency furnaces from Armco ingot iron, low-carbon ferrochromium and calcium molybdate and were poured into 2-in. ingots, which were forged to I-in. round bars. Sections of the bars were heated to the carbide-solution temperature and cooled rapidly to induce austenite transformation at relatively low temperatures. The steels were subject to some segregation, therefore comparatively high temperatures were necessary to dissolve all of the carbides. The microstructure of the quenched specimens was examined to verify the belief that the carbides had been dissolved, and also to determine the nature of the nonmartensitic structure of incompletely hardened steels. Ferrite and pseudo-martensite were present in some of the specimens, but all specimens were quenched at such a rate that pearlite was not formed, in order to ensure the formation of the carbides at temperatures lower than about 500°C. It had been found previously1 that in chromium steels the chromium carbide could be produced by transformation of austenite in the pearlite range above 500°C., and, in order to start the tempering treatment with the carbide present as cementite, the absence of pearlite was considered to be essential. The specimens were tempered for 64 hr. to permit the formation of the stable carbide. After tempering, the specimens were submitted to microscopic and X-ray examination. The carbides were separated either electrolytically in a 5 per cent HCl electrolyte or with an acidified copper-potassium chloride solution. The crystal structure of the carbide phases was determined by the Debye-Scherrer type of X-ray patterns. The X-ray patterns obtained from specimens near the boundaries between two types of carbides were generally weak and diffuse as compared with the other patterns. For this reason, and because the more soluble components may be masked, the boundaries between the phases could not be determined precisely. However, the X-ray analysis of electrolytically separated carbides has given consistently reproducible results

Jan 1, 1943

By S. H. Ash

IN no part of the world other than a small area in Pennsylvania is anthracite mining an industry of major magnitude. As the deposits of anthracite in the United States are limited virtually to Pennsylvania, the difficulties of this industry have been commonly considered a state rather than a national problem. However, there is also national interest in the conservation and wise utilization of all the country's fuel resources and in the control of interstate waterways. The anthracite industry is confronted with a serious problem of water accumulation in many of the mines, a problem that must be solved in the near future if progressively higher mining costs are to be avoided. It cannot be solved by the operating companies without state or Federal aid, or both, owing to the magnitude of the work required, the diversity of interests of the coal and surface ownerships, the hazard to the whole mining community, and interests affected outside the mining region. 'The costs of abating the ever-increasing surface seepage to mine workings and of handling this seepage once it has occurred are beyond the eco¬nomic resources of the operating managements.

Jan 1, 1941

By L. O. Howard

THERE are three active mines in the Chewelah-Colville district, the United Silver Copper near Chewelah, and the Old Dominion and the Chloride Queen near Colville. The Admiral near Valley is also doing development work. The Chewelah district is in the south central part of Stevens County in the Colville Valley. Chewelah, a thriving town of 1600 people, and the scene of operations of the Northwest Magnesite Co., is about the center of the district. It is situated in a farming community on the Spokane-Nelson branch of the Great Northern railway, about 65 miles north of Spokane. Only two or three of the mines in the district have been extensively developed, although many have been prospected. The general elevation of the valley, is about 1600 or 1700 ft., that of the mountain ranges on each side about 3000 to 4000 ft., with gentle slopes and rounded glaciated tops. Prospecting is often difficult because of much glacial debris.

Jan 1, 1925

By Charles H. Jacoby

The solution mining of evaporites has a history of approximately 5,000 years. The insitu leaching of metalliferous ore will have many of the same characteristic problems which have confronted industry for years in the production of evaporite minerals. Basically we will be converting the less soluble forms of valuable metals into their more soluble salts and producing these in much the same manner as, for example, sodium chloride. There are a number of problems which we are faced with that are more complex and complicated and, therefore, will require a higher degree of sophistication than previously employed. One of our most important undertakings will be the clearcut definition of the problems involved. While a great deal of expertise can be drawn from the solution mining of evaporites and the oil industry, problems peculiar to the hydrometallurgical field will need to be solved. One of these is the introduction of permeability into an impermeable rock so as to expose the sought after values of metals which by volume are infinitesimal when compared with sodium chloride, potash or other type water soluble mineralization. After establishing this permeability which will be miniscule when compared to a solution cavity, there will be the maintenance of this permeability. In general, salt deposits are of a somewhat uniform chemical composition and thus their chemistry was relatively simple. Each metalliferous ore body is somewhat unique in its chemistry and will need to be treated accordingly.

Jan 1, 1974

By C. B. Foster, S. I. Freedman, E. M. Jamgochian

Coal-oil mixture (COM) combustion technology is regarded by the US Department of Energy (DOE) as near term and Potentially applicable to existing utility and industrial steam generators and for injection into blast furnaces. From work done previously, it has been established that COM can be burned in existing boilers and blast furnaces. Therefore, the issues being addressed by the current DOE program are: (1) determination of best available technology to achieve environmentally acceptable long-term reliable operation and (2) determination of applications for which COM can be utilized economically. Some of the technological options have begun to be determined by projects already under way. However, many projects are still in the early stages of development.

Jan 1, 1980

By Ernest R. Lilley

THOSE acquainted with the fundamental differences between the, educational .systems of Great Britain and. the United States would hardly expect .the training of men for the petroleum industry to proceed along the same lines- in the two countries. The youth entering an English university is, except in the case of-the student from some of the British colonies or from foreign countries, almost invariably a product of the English "public school." This is in no sense comparable .with the American public school. It is a private institution, frequently of considerable age and heavily endowed. In many aspects it seems to be comparable with the American preparatory school. Yet to some extent its activities remind one of the first years of the undergraduate: course in the American college. Certainly it takes to-itself many of the social, functions of the American college.

Jan 1, 1931

By M. D. Hassialis

THE object of a technical paper is to communicate new technical knowledge, the paper being the vehicle of communication and the existence of new knowledge its reason for being. It follows that the development of information worthy of communication, the criterion being novelty, is prerequisite to exercising the privilege of communication. The act of communication is achieved when the reader perceives the nature of the new knowledge, i.e., when he understands it. A paper achieving this objective is an acceptable technical paper. Development of new knowledge has as one of its purposes the increase of the existing state of knowledge and the enjoyment of the benefits derived therefrom. Technical knowledge is a collection of facts so ordered as to make apparent, relations existing between the facts. When the interrelations have been exposed the facts have been interpreted or explained Three broad, overlapping categories of technical papers may be recognized: papers consisting of (a) a report of facts, (b) an explanation of facts, or (c) a combination of a report and an interpretation. Ideally a technical paper should belong to one of the last two categories but current practice is to accept papers belonging to any of the three categories. Based on a small sample drawn from the scientific and engineering literature, the relative frequency of the three types is a: b: c:: 20:1:14. If the sample be limited to engineering literature, the ratios become a:c::2:1; type (b) being nonexistent. This large departure from the ideal is a consequent of the

Jan 1, 1948

By Halbert Powers Gillette

In every chemical reaction heat is either developed or absorbed, and this plus or minus heat of formation is as definite in quantity as the weights of the reacting elements. In this paper I shall show that each chemical element and each chemical radical has its own definite heat-valency,—a fact which, so far as I know, has hitherto escaped the attention of investigators, but, I feel sure, will be admitted after the demonstration here given, and may lead to some practical conclusions of value. When Berthelotys " law of maximum work " was found to have so many inexplicable exceptions, the pendulum of a scientific theory swung away from a recognition of the truth underlying that proposition; and this reaction went so far that not only has thermal chemistry been relatively neglected by recent investigators, but it is not uncommon now to find textbooks on physical chemistry which practically ignore all that Thomsen, Berthelot and others have done. To this temporary tendency of thought I attribute the failure to recognize the principles herein announced and explained. Not long ago, while studying tables of the formation-heat of various salts, I noticed that in this respect all potassium salts in solution differ from the corresponding sodium salts by 9.3 cal.1 I found also that similar differences exist between other salts, not only when the basic radical is varied, while the acid radical remains constant, but also when the acid radical is the variable. Thus chlorine salts in solution differ from bromine salts in this respect by 10.9 cal. Upon further study, I found that Thomsen had noted similar constant differences, but, so far as I can ascertain, he appears to have attached no great significance thereto.

Jan 1, 1904

By Willard S. Morse

The purpose of this paper is to record the results obtained in the use of the Russell process at Aspen, Colo., covering a period of fourteen months, from November, 1891, to December, 1892, during which time over 30,000 tons of ore, purchased outright, on sample and assay, were treated. No explanation of results will be attempted, nor will the chemistry of the process be discussed. The plant was designed by C. A. Stetefeldt, of San Francisco, and built by the owners by day-labor. The entire plant is run by water-power, supplied by a flume 3600 feet long, and a pipe-line 2200 feet long, with a head of 170 feet. A Pelton water-wheel, 8 feet in diameter, is used, from which power is transmitted by wire-rope to the main counter-shaft in the mill, a distance of about 250 feet. From the mill to the samplingworks, about 150 feet, power is also transmitted by a wirerope. A Pelton water-wheel, 3 feet in diameter, supplies power to the dynamo for lighting the plant. The works are located adjoining the Santa Fe railroad tracks, and all ore and supplies are unloaded directly from the cars to the works. The sampling-works are provided with crushers and rolls, the latter being used only on samples, and not on the entire ore. The Cornish hand-quartering method is used in sampling ore for purchase. After crushing and sampling, the ore goes to the bedding-floor, where it is made up into mixtures suitable for the mill. The drying-plant consists of four Stetefeldt double shelfdryers, six shelves high, and is provided with dust-chambers and a stack 65 feet high for draft. These dryers are fired with gas

Jan 1, 1896

Occasionally it is interesting, and sometimes useful, to review the past for early references to our industry, and to learn of the trials and travail passed through before it arrived where it now is - and the results of such a review follow. Some time ago one of our modern playwrights and poets, Arthur Guiterman, turned to coal, with the following result : Afar in the Carboniferous time I grew in Paleozoical slime, A lepidodendron with boughs on my stem And lepidostrobusea grew out of them. My roots in the mud of the ages I spread And up to the heavens I vaunted my head, I throve in the heat of tropical sun, And now I am coal at two dollars a ton.

Jan 1, 1935

By W. P. Ward

I desire ho put on record a fact in relation to the effect of man ganese on pig iron which I have never seen in print, and which may, perhaps, not have been observed by anyone except myself. In 1875, while experimenting on the production of ferroman ganese in a blast furnace, I had burdened the furnace with a charge which I calculated would produce a 15-per cent. spiegel. The fur nace was very hot, having been running for a couple of days on a very light burden, and making a burnt iron, preparatory to the experiment I proposed to make to produce a high grade of spiegel. I calculated that the charge would begin to work in the fur nace in about twelve hoars after it was put on. After the -lapse of that time I commenced to watch the furnace carefully, but found little or no change in the appearance of the metal, although there was a very decided change in the cinder, showing that the man ganese ore had come in work. The iron was quite gray and very tough. The character of the cinder was good for a spiegel cinder, and 1 could not imagine where the manganese was going to, as it (lid not appear to be in either metal or cinder in anything like the quan tity indicated by the charge. The next morning things were still in the same condition. The furnace was very hot, the cinder good, and the iron very gray. I was then sorely puzzled. I had never heard of a gray iron with over 4 or 6 per cent. of manganese, and had no notion that an iron with more manganese could be gray and tough. With great difficulty a piece for chemical test was broken from a pig. Not less than a hundred blows from a heavy sledge were required to break it off, I took the specimen to the shop and directed that some borings from it should be brought to the laboratory, as soon as possible, whither I myself at once repaired to put things in readi ness for a rapid manganese determination. In about half an hour the machinist came in with the iron specimen in one hand and about a dozen blunted and broken steel drills in the other, saying that it mas impossible to drill the iron. There were several little depressions in the iron, which was malleable enough to be indented by the point of the drill, but not a chip had been cut from it. The metal was never subjected to further physical tests. A chip broken from

Jan 1, 1882

By Richard J. Lund

Stock piling-and by that I mean well-organized stock piling on a substantial scale-is almost as old as the hills themselves. It was back in early Biblical times, as recounted in the Book of Genesis, that Joseph was charged by Pharaoh with the responsibility of stock piling food during the seven years of plenty to guard against the seven subsequent years of famine that were revealed by the Pharaoh's dream. And this same policy of storing up food or materials to provide for future anticipated emergencies can be traced repeatedly down through the ages. So our own efforts are anything but new. Our modern concept of stock piling-the purchase and storage of strategic materials to assure supplies needed in time of some future war- stems from our experience in World War I. In 1920, the War Department was charged by Congress with the responsibility of procuring all War Department supplies and mobilizing industry in the event of another war. During the two decades that followed there were many authoritative studies made of our deficient mineral problem, all of which pointed out the urgent necessity of stock piling certain strategic materials as a reserve against future war. One such study, made in 1925 through the combined efforts of the Mining and Metallurgical Society and the AIME, was done at the ex- press request of the War Department. Eight years later another more de-

Jan 1, 1949

By W. H. Basssett

THE amount of oxygen present in refined copper bears an important relation to the effects of various impurities on physical properties of copper, as well as the effects of reducing gases at higher temperatures. It seems fitting at this time, when the effects of reducing gases on copper are being discussed, to describe methods that have proved satisfactory for the determination of oxygen and sulfur, and to present some results obtained by investigation of these methods in the authors' laboratory. The procedure for the determination of sulfur is closely interrelated with that for oxygen and has, therefore, been included. It was first proposed by Hamper that oxides in copper could be accurately determined by the loss in weight sustained by finely divided copper when reduced at red heat in pure hydrogen, or by the weight of water produced. Hampe's method was later modified by Archbutt,2 who established the accuracy of the method and demonstrated that equally accurate results were obtained by noting the loss in weight or by weighing the water formed. The determination of oxygen by heating in carbon monoxide has been proposed by West.3 In our hands this method has given slightly lower results than obtained by heating in hydrogen.

Jan 2, 1926

By M. ROWE, H. E. Gilliland, L. BARNES

The authors of this paper are to be commended for a clear exposition of a timely subject. However, some important conclusions, in addition to those presented in the paper, can be drawn from the results of their elaborate and rather complete numerical computations. First of all, the major part of the calculations presented in the paper are for semi-infinite slabs of oil shale (the authors designate this as Model I) and a question must be posed — Are these elaborate computations needed to arrive at realistic estimates of the shale oil displaced. Consider the model of Lauwerier* that corresponds to the authors Model I if thermal conduction parallel to the fracture be neglected. If one also neglects the finite (but relatively small) heat capacity of the material in the fracture, it is easily shown from Lauwerier's solution that the cumulative oil production would be:

Jan 1, 1969

By W. Crafts, J. L. Lamont

Electrolytic extraction of carbides from quenched and tempered steel and their examination under the electron microscope were found to be helpful in understanding the mechanism of secondary hardening in alloy steels1 and the same technique has been applied to isothermally transformed steels. A preliminary survey of the utility of the method has indicated that it has promising possibilities for investigating the characteristics of pearlite and bainite. The examination of a few carbon and chromium steels has suggested that pearlite is formed with carbides of two varieties representing the lamellar and nonlamellar forms and that bainite appears to form with a structure analogous to, but significantly different from, martensite. Procedure The method used for examining the carbides was similar to that described previously.1 The chromium steels used in the investigation were made from an Armco iron base in an induction furnace and were not treated with grain-refining deoxidizers. The composition of the steels is given in Table 1. Three-inch square ingots were forged and rolled to 1/8-in. thick sheet for use in the isothermal studies. After rolling, the sheets were sandblasted to remove the rolling scale. Specimens approximately 3/4-in. wide and l1/2-in. long were prepared from the 1/8-in. sheet. They were heated in a salt "bath at 2100°F (1150°C) for 1/2 hour, transferred to other salt baths at 1300°F (704°C), 1000°F (538°C), 800°F (426°C), or 600°F (315°C), held for various periods up to 100 hr and finally quenched in water. After quenching, the specimens were cut in half, one half being submitted to microscopic examination and the other half being used for the electrolytic extraction. The isothermally transformed specimens were submitted to examination under the light microscope to determine the degree of transformation and type of structure and were photographed at 2000 X. Carbide residues were obtained by electrolyzing in 10 pet hydrochloric acid and collecting the residue in glycerine to minimize attack by the acid. As pointed out in the earlier paper, the carbides are attacked to some degree during electrolysis. This attack is relatively minor on the coarser carbides but may be quite severe on the fine bainitic carbides. The residues were washed free of the glycerine with water and alcohol. The alcohol was removed by repeated washings of amyl acetate, and the amyl acetate suspensions were transferred to stoppered vials. Debye-Sherrer X ray diffraction patterns of the residues were prepared using a chromium target. A selection based on the microstructure and X ray data was then made of samples considered most illustrative of the progress of transformation. Electrolytically extracted residues from these samples were submitted to examination by W. D. Forgeng and A. C. Jenkins on the electron microscope at the Research Laboratories of The Linde Air Products Co. and electron micrographs were made at X 5000 and enlarged to 25,000 X. The micrographs obtained with both the light and the electron microscopes are mounted side by side in the accompanying figures. Although no effort was made to establish the T-T-T diagram for the chromium steels, the times for holding in the salt bath were adjusted with the intention of making the samples represent different stages in the transformation at temperatures of 600, 800, 1000, and 1300°F. The degrees of transformation and results of X ray examination are shown in Tables 2—4. The carbide designations refer to orthorhombic or trigonal carbide types and are not meant to imply that the compositions are exactly as indicated. X ray Diffraction Data The occurrence of Fe3C and Cr7C3 in these steels was found to be consistent with published data on comparable chromium steels. Steels A and B with relatively low ratios of carbon to chromium contained Cr7C3 in the pearlitic structures and FeuC in the

Jan 1, 1950

By Frank Firmstone

(Ottawa Meeting, October, 1889. Substituted for the briefer note on the same subject. pre sented at the meeting and subsequently distributed in preliminary pamphlet edition.) Prof. H. Hoefer's theory of blasting was published in the Oesterr. Zeitschrift, xxviii., 1880, and xxix., 1881; and Part 111. in Nos. 15, 16 and 17, xxx., 1882, and subsequent numbers of that

Jan 1, 1890

Jan 1, 1879

THE Institute met on Wednesday evening, May 22d, in the parlor of the Stanton House, Dr. T. Sterry Hunt, President, in the chair. The President delivered an introductory address on the Brown Hematite Deposits of the Great Valley, after which the following papers were read and discussed : Note on the Result of an Experiment with the Wheeler Process of Combining Iron and Steel in the Head of a Rail, by W. E. C. Coxe, of Reading, Pa. On the Jenks Corundum Mine, Macon County, N. C., by Dr. R. W. Raymond, of New York City. On Wednesday afternoon, previous to the opening session, the members who had already arrived in Chattanooga, were taken by the Local Committee to the works of the Roane Iron Company, and Chattanooga Iron Company, and then to the top of Lookout Mountain, where, at the request of the members present, Dr. Hunt described the geological and geographical features of the Chattanooga region, with the magnificent panorama spread out before them as a map. On Thursday morning an excursion was made by steamboat down the Tennessee River as far as Shellmound. Here cars were taken to the coal mines of the Dade Coal Company, where the members were courteously received by Mr. E. B. Wells, the Superintendent. After a trip through the mines the party partook of a collation provided by the company. South Pittsburgh, on the Tennessee River, was next visited, where the Southern States Coal, Iron and Land Company have a large blast-furnace plant in the course of erection. After conducting the party through the works, shops, etc., Mr. James Bowron, the manager, entertained the members with graceful hospitality at dinner. The second session was held on Thursday evening for the transaction of business. The President, Dr. T. Sterry Hunt, appointed Messrs. W. E. C. Coxe, R. H. Richards, and F. J. Slade, scrutineers, to examine the ballots for officers for the ensuing year.

Jan 1, 1879

By A. S. Richardson

THE design of mine airways receives, in general, very little engineering treatment. To a large extent this is, of course, due to the fact that information upon which to base calculations is seldom available in definite form. In many mines the extent of the workable deposits may not be known at the time an air course is planned, and the length of service is indeterminable. Volume of air required for ventilation may also increase with extension of the life of a property, and natural obstacles, such as heavy ground, often place limitations upon the size of opening that can be maintained. Perhaps a majority of the shafts used in ventilation of metal mines were originally intended as hoisting shafts, and many of the tunnels and cross-cuts similarly used, were also designed as haulage ways or for other operating purposes. Even when a shaft is sunk solely for ventilation, custom usually dictates a size and shape consistent with the type commonly used for ordinary operations, because experience has demonstrated it can be excavated and maintained. In fact it may not be very far wrong to say most ventilation openings were never made with any consideration as to economic design for such use. When an air course is required to pass air between different parts of mine workings under a fixed pressure, the size of opening required for a given volume of flow, is, of course, determined by the resistance factor of the air course. It is then impossible to proportion the opening with reference to economics of power consumption, and this paper is limited to the design of openings where ventilation pressure or power consumption may be varied for economic advantage.

Jan 2, 1926