Search Documents

By A. S. Richardson

AIR conditioning, or air cooling, for the improvement of ventilation in the Butte mines has come into increasing use during the past 10 years. In part, the methods practiced have been described in previous publications of the Institute, but some improvements on earlier methods have been made and a number of new features have been developed. This paper is presented as a record of progress made, and for the sake of completeness describes all general features of the work. The need for air conditioning in the ventilation of mines in the district arises from the fact that the temperature of the ground and mine water has shown a very great increase with increase in mining depth, and has now reached a maximum of slightly over 130ºF. The most difficult part of the ventilation problem is the maintenance of temperature and humidity of a satisfactory standard in the working places, especially on the lower levels. Although ordinary ventilation is adequate to maintain good conditions in most of the working places it is subject to a number of limitations at great depth. Most important among these limitations is that with increase in depth the air becomes heated before it reaches the working places, both by compression from increase in atmospheric pressure and by heat transferred to it from rock at high temperature, so that its capacity for lowering temperatures is greatly reduced before it reaches the operating zone. Increasing depth of mining also increases the distance traveled by the air in its passage through the mine, and this causes a corresponding increase in resistance to air flow, so that there is greater difficulty in maintaining even the same volume in circulation. Thus, in the face of a demand that the ventilating system have a very much greater capacity to remove heat from the mine, the tendency is for that capacity to diminish. The only evident alternatives were (I) the opening of additional air shafts to increase the volume of air in circulation, (2) an extension of the existing system that would be subject to the same limitations, or (3) the adoption of an entirely different method such as air cooling. Fortunately for an economic solution of the problem, the mean annual temperature of the surface atmosphere at Butte is about 40°F., with very low relative humidity in summer, so that there is unlimited natural cooling power at a temperature range adaptable to air-conditioning methods. METHODS Two similar methods of air conditioning are used, as necessitated by service requirements and dependent upon the equipment available. In one, which is the more important and has the greater cooling capacity, water is circulated in a closed circuit, and, alternately, first absorbs heat from warm mine air and then dissipates it in the surface atmosphere by cooling at a cooling tower. The second

Jan 1, 1941

By AIME AIME

THE PAPER, "Surface Effects on Assay Beads Caused by Metals of the. Platinum Group," presented by J. L. Byers, before the Institute of. Metals Division at the February meeting of the Institute, is the subject of interesting discussion, an abstract of which follows. The original paper is available at Institute headquarters as a Preprint. Member-What assurance have you that the percentage of metals, as stated, is really an accumulation?

Jan 1, 1932

By AIME AIME

REPUBLIC STEEL'S new iron blast furnace in Alabama, shown on the cover of this issue, is the first to be completed of those authorized by the Government last year when a shortage of scrap became acute. In addition to the furnace, the new equipment includes a new battery of by-product coke ovens, a boiler plant, a generating unit, a 3-mile-long 60-in. water line, a huge gas washer, and precipitators in which the dust from the furnace is washed, separated from the water, and fed back into the furnace as raw material. The new unit is a cylindrical steel giant reaching 130 ft. into the air above the ground level. Because of the high humidity in the deep South, the furnace has been air-conditioned to avoid blowing eighteen tons of water into the furnace daily. Designed by Republic engineers who also had charge of the actual construction, the new furnace incorporates the best in modern blastfurnace practice. Orders to proceed with the construction of the furnace were received Sept. 22, 1941. The engineering crew, which was immediately organized, made more than 1500 drawings. Excavation started the next day, and simultaneously work was begun on demolishing existing buildings and preparing the site. The first concrete was poured Oct. 7 and the first piece of steel swung into place by a giant derrick on Jan. 30, 1942. It began operating May 28. A total of 70,000 cu. yd. of earth was moved and 30,000 cu. yd. of concrete poured.

Jan 1, 1942

By A. S. Richardson

AIR conditioning, or air cooling, for the improvement of ventilation in the Butte mines has come into increasing use during the past 10 years. In part, the methods practiced have been described in previous publications of the Institute, but some improvements on earlier methods have been made and a number of new features have been developed. This paper is presented as a record of progress made, and for the sake of completeness describes all general features of the work. The need for air conditioning in the ventilation of mines in the district arises from the fact that the temperature of the ground and mine water has shown a very great increase with increase in mining depth, and has now reached a maximum of slightly over 130°F. The most difficult part of the ventilation problem is the maintenance of temperature and humidity of a satisfactory standard in the working places, especially on the lower levels. Although ordinary ventilation is adequate to maintain good conditions in most of the working places it is subject to a number of limitations at great depth. Most important among these limitations is that with increase in depth the air becomes heated before it reaches the working places, both by compression from increase in atmospheric pressure and by heat transferred to it from rock at high temperature, so that its capacity for lowering temperatures is greatly reduced before it reaches the operating zone. Increasing depth of mining also increases the distance traveled by the air in its passage through the mine, and this causes a corresponding increase in resistance to air flow, so that there is greater difficulty in maintaining even the same volume in circulation. Thus, in the face of a demand that the ventilating system have a very much greater capacity to remove heat from the mine, the tendency is for that capacity to diminish. The only evident alternatives were (I) the opening of additional air shafts to increase the volume of air in circulation, (2) an extension of the existing system that would be subject to the same limitations, or (3) the adoption of an entirely different method such as air cooling. Fortunately for an economic solution of the problem, the mean annual temperature of the surface atmosphere at Butte is about 40°F., with very low relative humidity in summer, so that there is unlimited natural cooling power at a temperature range adaptable to air-conditioning methods. METHODS Two similar methods of air conditioning are used, as necessitated by service requirements and dependent upon the equipment available. In one, which is the more important and has the greater cooling capacity, water is circulated in a closed circuit, and, alternately, first absorbs heat from warm mine air and then dissipates it in the surface atmosphere by cooling at a cooling tower. The second

Jan 1, 1941

By A.S. Richardson

AIR conditioning, or air cooling, for the improvement of ventilation in the Butte mines has come into increasing use during the past 10 years. In part, the methods practiced have been described in previous publications of the Institute, but some improvements on earlier methods have been made and a number of new features have been developed. This paper is presented as a record of progress made, and for the sake of completeness describes all general features of the work. The need for air conditioning in the ventilation of mines in the district arises from the fact that the temperature of the ground and mine water has shown a very great increase with increase in mining depth, and has now reached a maximum of slightly over 130°F. The most difficult part of the ventilation problem is the maintenance of temperature and humidity of a satisfactory standard in the working places, especially on the lower levels. Although ordinary ventilation is adequate to maintain good conditions in most of the working places it is subject to a number of limitations at great depth. Most important among these limitations is that with increase in depth the air becomes heated before it reaches the working places, both by compression from increase in atmospheric Pressure and by heat transferred to it from rock at high temPerature, so that its capacity for lowering temperatures is greatly reduced before it reaches the operating zone. Increasing depth of mining also increases the distance traveled by the air in its passage through the mine, and this causes a corresponding increase in resistance to air flow, so that there is greater difficulty in maintaining even the same volume in circulation. Thus, in the face of a demand that the ventilating system have a very much greater capacity to remove heat from the mine, the tendency is for that capacity to diminish. The only evident alternatives were (I) the opening of additional air shafts to increase the volume of air in circulation, (2) an extension of the existing system that would be subject to the same limitations, or (3) the adoption of an entirely different method such as air cooling. Fortunately for an economic solution of the problem, the mean annual temperature of the surface atmosphere at Butte is about 40°F., with very low relative humidity in summer, so that there is unlimited natural cooling power at a temperature range adaptable to air-conditioning methods. Methods Two similar methods of air conditioning are used, as necessitated by service requirements and dependent upon the equipment available. In one, which is the more important and has the greater cooling capacity, water is circulated in a closed circuit, and, alternately, first absorbs heat from warm mine air and then dissipates it in the surface atmosphere by cooling at a cooling tower. The second

Jan 1, 1943

By A. S. Richardson

AIR conditioning, or air cooling, for the improvement of ventilation in the Butte mines has come into increasing use during the past 10 years. In part, the methods practiced have been described in previous publications of the Institute, but some improvements on earlier methods have been made and a number of new features have been developed. This paper is presented as a record of progress made, and for the sake of completeness describes all general features of the work. The need for air conditioning in the ventilation of mines in the district arises from the fact that the temperature of the ground and mine water has shown a very great increase with increase in mining depth, and has now reached a maximum of slightly over 130°F. The most difficult part of the ventilation problem is the maintenance of temperature and humidity of a satisfactory standard in the working places, especially on the lower levels. Although ordinary ventilation is adequate to maintain good conditions in most of the working places it is subject to a number of limitations at great depth. Most important among these limitations is that with increase in depth the air becomes heated before it reaches the working places, both by compression from increase in atmospheric Pressure and by heat transferred to it from rock at high temPerature, so that its capacity for lowering temperatures is greatly reduced before it reaches the operating zone. Increasing depth of mining also increases the distance traveled by the air in its passage through the mine, and this causes a corresponding increase in resistance to air flow, so that there is greater difficulty in maintaining even the same volume in circulation. Thus, in the face of a demand that the ventilating system have a very much greater capacity to remove heat from the mine, the tendency is for that capacity to diminish. The only evident alternatives were (I) the opening of additional air shafts to increase the volume of air in circulation, (2) an extension of the existing system that would be subject to the same limitations, or (3) the adoption of an entirely different method such as air cooling. Fortunately for an economic solution of the problem, the mean annual temperature of the surface atmosphere at Butte is about 40°F., with very low relative humidity in summer, so that there is unlimited natural cooling power at a temperature range adaptable to air-conditioning methods. Methods Two similar methods of air conditioning are used, as necessitated by service requirements and dependent upon the equipment available. In one, which is the more important and has the greater cooling capacity, water is circulated in a closed circuit, and, alternately, first absorbs heat from warm mine air and then dissipates it in the surface atmosphere by cooling at a cooling tower. The second

Jan 1, 1943

By A. M. Kivari

OPERATIONS at the cement plant of the Permanente Corporation, in the hills about 45 miles south of San Francisco and 12 miles west of San Jose, are interesting to the members because of the adoption of modern hydrometallurgical methods for handling and beneficiating raw materials Closed-circuit grinding, classification, hydroseparation, flotation, agitation, and thickening are familiar terms at this cement plant These methods make it possible to process refractory limestone into suitable materials for the manufacture of modern cements Construction of the plant, haying originally a design capacity of 7000 bbl of cement per clay, was started in June 1939, and the first clinker was ground on the following Christmas Day At present the capacity is about 12,000 bbl of finished cement per 24 hr , most of the production being low-heat cement † About 3130 tons of limestone, 620 tons of clay and 100 tons of gypsum are required daily for this output Occasionally iron oxide is added to the clay to obtain the desired composition This, together with the gypsum, is purchased from outside sources Up to the present time, the corporation has produced low-heat, normal, moderate¬ heat, moderate-sulphate-resisting, high-early-strength, oil-well, modified-oil-well, and plastic cements Most of the present production is for Shasta Dam, near Redding, Calif , the told demand being 5,800,000 bbl of cement Following are sonic of the cement requirements of the Shasta D [im] specifications [ ] The average specific surface in the bin s sampled shill be not less Ulan 1800 sq cm per gram and no individual sample less thin 1600 sq centimeters Compressive strength The average compressive strength in pounds per square inch of three mortar cubes composed of one part cement and 2 75 parts fine testing sand, by weight, shall be equal to or greater thin the following

Jan 1, 1941

By D. M. McFarland

IN mining, quarrying, and construction, drilling and blasting have an important influence on the operations that follow. If the fragmentation of material being disrupted is inadequate, loading and transportation equipment will not operate at or near full capacity. Any operator faced with this difficulty should not be satisfied until he is convinced by a careful study of his methods of drilling and blasting that no improvement can be made. Rock in a certain quarry in Ohio seemed to defy any grade of explosive or means of detonation that the explosives industry had to offer. The average result of a blast was that a great part of the burden would be pushed out from the face in a number of large sections that would jokingly be referred to as "boxcars." These were no credit to the explosives man and a costly problem for the quarry company. Such blocks retard shovel operation as they have to be uncovered and subjected to secondary drilling and blasting which, if extensive, is an expensive operation. It was an attempt to improve the fragmentation obtained in primary blasts that led to the development of milli-second-delay electric blasting caps. The reasoning that prompted the trial was that even with wide spacing of the drill holes it seemed that the burden was separated too quickly from the face by the cutting action of the explosives from hole to hole. If the time of firing of the holes could be regulated so that

Jan 1, 1948

By T. W. Turk, S. A. Sass

The engineering design features of the Mercur Gold Project crushing, grinding, carbon-in-leach, bullion, reagent, and tailings disposal areas will be discussed in this paper. It presents a project overview and flowsheet along with selected design alternatives. During the engineering phase, major equipment and other features were selected to optimize design within site location and environmental constraints. The project team organization and procedures were adopted to accommodate multiple optimization studies while maintaining a tight engineering schedule.

Jan 1, 1985

By AIME AIME

THE official opening at the 134th general meeting of the Institute was held on Oct. 6, but it was prefaced by two round table conferences on Oct. 5. The open-hearth group held the fourth of their semi-annual conferences at the William Penn Hotel, devoting the morning session to discussing a paper by R. L. Cain on the "Manufacture of Forging Steel by the Open-hearth Process," and the afternoon to discussing P. H. Shaeffer's paper on the open-hearth charge. At the Bureau of Mines, a round table conference on the combustibility of coke was held on Tuesday morning, and the afternoon was devoted to a similar conference on the testing of coke. The formal opening session of the meeting assembled in the Music Hall of Carnegie Institute at 10.30 a. m. Graham Bright, chairman of the Pittsburgh Section; called the meeting to order and presided. President Taylor welcomed the visiting members and guests to his home city and reviewed briefly the advancement of mining in the past half century during which, for ex- ample, the coal output had increased from 53,280,000 tons to 523,357,000 tons per year. He emphasized the important part Pennsylvania played in mining and brought out the principal changes that had taken place in methods. In part, his remarks were as follows: The centennial year, 1876, found the coal business of. this country, as a whole, producing 53,280,000 tons, of which amount the bituminous mines of this State yielded 24 per cent. In 1925, this country produced 523,357,000 tons of coal, of which Pennsylvania produced 24 per cent.

Jan 1, 1926

By D. R. Parrish, F. F. Craig

In some respects, forward combustion (alias: fie-flooding, underground combustion, in-situ combustion, dry combustion) is an efficient oil recovery method. For example, its displacement efficiency (as much as 95 percent in reservoirs with high porosity and high oil saturation) is good. In its use of heat, however, forward combustion is grossly inefficient. Most of the heat generated during forward combustion is wasted. About one-fifth of the heat is picked up by the incoming air and re-used (regenerated); the remainder is left behind the combustion zone and ultimately is lost. Compressed air is expensive, and heat generated from compressed air via underground combustion is too valuable to be thrown away. Improvement is needed. Since the early 1950's, improvements in forward combustion by addition of water injection have been discussed, particularly in the patent literature, with increasing frequency.'-'' These concepts are based on the fact that relatively inexpensive water can be used to pick up much of the heat that is ordinarily wasted during forward combustion, and transport it forward to a more useful place, thereby reducing the amount of air required to move a heat front through the reservoir. Several approaches have been proposed. Merriam and Squires1 taught that a combustible (fuel) gas should be injected along with the air and water. This, however, would give at least a tendency toward reverse combustion instead of forward combustion, and would reduce the velocity of the heat bank, defeating the primary purpose of the water injection. Pelzer2 described primarily a batchwise method of forward combustion and water flooding. He advocated burning part way through a reservoir with forward combustion, then switching from air to water injection alone to push the heat toward the producing wells. Though possible, this method has serious disadvantages, the major one being that, by the time water injection is started, much of the heat has been irretrievably lost to the overlying and underlying formations. We have described what is considered a practical Combination Of Forward Combustion And Water-flooding (COFCAW).3,4 Air and water are injected simultaneously (or alternately) after a small heat bank has been formed by forward combustion. Some of the injected fluid fills up the region behind the heat bank; the rest enters the heat bank. Upon encountering heated rock, the water is converted into steam, which then flows ahead of the combustion zone and displaces much of the oil in place. Only enough air is injected to provide heat for vaporization of the water and to compensate for reservoir heat losses. Since the size of the heat bank is minimized, heat losses also are minimized. Because of more efficient oil displacement ahead of the combustion zone, fuel consumption is reduced. Too, unlike a forward combustion zone that cannot move until all fuel at a point has been consumed, COFCAW leaves some

Jan 1, 1970

By H. M. Howe, A. G. Levy

§ 1 Introduction.—This paper gives the results of our micro-graphic determinations of the position of Ae3 in a series of 14 hypo-eutectoid steels of varying carbon content, one of them very rich in phosphorus, and of SEe for one hyper-eutectoid steel. We have proceeded chiefly by noting the temperature at which the reabsorption of the pro-eutectoid element is found to be complete after a 30-min. holding, but in part also by noting the temperature at which its precipitation begins. Observations on these same steels by Messrs. Burgess, Crowe, and Rawdon, of the United States Bureau of Standards, are given in a paper1 issued simultaneously with this, while in a third paper2 one of us compares these data with those of earlier observers. These three papers are treated as one whole by numbering their sections, tables, and illustrations continuously, and by setting the folding plates of micrographs at the end of the last paper. The Composition of the Steels Experimented On is given in Table I. § 2. Notalion and Definitions.—Following Osmond's development of Tschernoff's notation, in which " Ac3 " is the upper limit of the hypo-eutectoid part of the transformation range as observed in heating up, and " Ar3 " is that same limit as observed in cooling down, and following the usual custom of calling the upper limit of the hyper-eutectoid part of that range " SE," we may go farther and call this latter limit " SEc" when observed in heating up and " SEr " when observed in cooling down. Further, we may call the equilibrium position of these lines, i. e., the position which they would have in pure iron-carbon alloys if all

Jan 1, 1914

By AIME AIME

THE fall meeting of the Petroleum Division, held at Tulsa, Okla., on Oct. 11 to 14, devoted two days to technical sessions and two to field excursions. A representative attendance of 250 to 300 engineers and operating officials engaged in oil production marked the sessions and paid close attention throughout to a notable series of highly technical papers. Restricted as the program was to consideration of production problems only, the time proved too short for discussion or even the presentation of the 20 papers submitted. Much informing and pertinent discussion none the less took place, and the sentiment was general to the effect that the meeting was one of the best ever held by the Division. The meetings were held in the auditorium of the Municipal building and local arrangements were well looked after by the Mid-Continent Section of the Institute and the Oil and Gas Association. The combination of the three organizations served to bring together engineers and operators most usefully. F. Julius Fohs, chairman of the Division, presided at the sessions on Monday. Tuesday morning John M. Lovejoy of the local section took over this responsibility in the absence of T. E. Swigart, who was detained in California. The afternoon session was presided over by A. G. Heggam of the Oil and Gas Association and the Tuesday evening banquet by W. C. Franklin of the same organization.

Jan 1, 1926

By AIME AIME

APROXIMATELY one third of the world's iron ore is mined in the United States; and about 80 per cent of this third is mined in the Lake Superior ore region, and about 60 per cent in Minnesota. The Lake Superior iron ore region covers a vast area in the vicinity of Lake Superior that contained in early geological times large areas of iron-bearing sediments, which today form metamorphosed iron-bearing rocks, such as jasper, chert, taconite, and slates. Concentration of the iron content chiefly through solution and resultant removal of silica produced the ore bodies we find today in rock folds as on the Menominee range, at dike or impervious wall intersections such as on the Gogebic range, and blanket-type enriched ore bodies ly¬ing on or within the ore formation, such as occur on the Mesabi and in steeply pitching ore lenses elsewhere. In many places, folding and subsequent erosion of the tops of the folded areas has resulted in steep dips in the ore formation and contained ore bodies. The upper eroded edges are mostly buried under glacial over-burden. The slightly dipping Mesabi formation is the principal exception as to steeply dipping ore bodies.

Jan 1, 1941

By C. H. Benedict

Largest and most important of the milling plants under construction during the year is the Morenci plant of the Phelps Dodge Corp., in Arizona, where plans are being rushed for production in 1942. Grate mills will be used for fine-grinding, and in the pilot plant, classifiers of the spiral type have the preference for the closed- circuit work. The flotation units will be chiefly of the pneumatic type, with some mechanical units as auxiliaries. The Fagergren, Pan American, and Agitair machines were left in the competition as the year closed. If the absence of European markets for finished products has dislocated the mining industry, fortunately the lack of raw materials required in the beneficiation of ores has not been serious. except possibly as to the inability to import flint grinding pebbles. Some of the less important gold mines still use pebbles for grinding as is also the practice in the comminution of nonmetallics used in various industries. T the Calumet & Hecla in the Lake A Superior copper district pebbles have been used exclusively in open- circuit grinding in the Hardinge mills treating the

Jan 1, 1941

By E. L. Oliver

IN OFFERING a few comments and suggestions on trends in mining practice, and the methods and tools of tomorrow's mining, perhaps it will be appropriate to start with the subject of education. Charles Kettering, one of the best-known scientists and experimentalists in the automotive industry once said, in effect, that tech- 111ca1 schools have to be carefid not to teach a lot of hard and fast rules that may have been true once, but aren't so any more, or won't be presently. Possibly the mining school of the future will concern itself less with what has happened and more with what is going to happen. It will be built about or around problems. Such a school will be judged, not by the number of its students but by the quality of its improvements. To such a school the industry will send for men to solve particular problems. The industry will doubtless at some time sup- port such a school financially though a lot of hard work will be required to organize miners to undertake such financing, primarily because the mining industry, other than that concerned with iron and steel, is too loosely knit. Each company tends to its own knitting too closely for its own good. Wouldn't it be splendid if the mining industry would finance a "problem school" as suggested by Mr. Kettering and others.

Jan 1, 1939

By Haley, D. F.

WHEN operations were first started at Climax in 1917 by the Climax Molybdenum Co., they were pioneering in the molybdenum industry for little was known relative to the uses of molybdenum or the metallurgy of molybdenite concentration. Concentration of molybdenite is relatively simple today but in 1916, when the Climax deposit first attracted attention, it presented serious difficulties. Little was known, in fact, even about the assaying of such low-grade molybdenum ores. Mine samples were sent to at least a dozen of the best laboratories in the United States and average values reported varied from 0.4 per cent to 1.0 per cent MOS2. Owing to the wide variations in MoS2 content obtained from reliable chemists, the actual value of the ore was most uncertain. This variation occurred repeat¬edly over a period of six months in 1917. It was finally decided, as a last resort, to cut several tons of sample from the tunnel and have a mill test made, using the recovered MoS2 per ton as the grade of the ore, for a small error in the assaying of the concentrate would not materially affect the results. These mill tests were made by the General Engineering Co. (Callow) at Salt Lake City. The results proved an ore of commercial grade and indicated the flotation process for the best metallurgy. Based upon these tests, the decision was made to build a 200-ton flotation plant. At this time, the art of flotation was

Jan 1, 1946

Philip Argall, Denver, Colo. (communication to the Secretary) : Mr. Rickard expresses regret that I have not given more extracts " from the fresh leaves of nature's open book." The quotations used by me in argument were all from nature's open book, and by authorities recognized in the scientific world as being able to decipher nature's unwritten pages, if not lay bare her inmost secrets. The study of -nature should be preceded by a knowledge of her laws. Natural science is but the summary of the observations of the past or an organized and accurate knowledge of the order in which things have been observed to happen. One who ignores the 'knowledge of the past or despises that of the present and approaches nature's open book with a virgin mind but too often finds her

Jan 1, 1895

By O. M. TUPPER

REQUIRING a finer ground clay than that obtainable with a dry pan or hammer mill, the Clay Corporation of California installed a five-roller, low- side Raymond impact mill at its Lincoln plant in 1925 and since then has been economically grinding fire clay with a moisture content as high as 15 per cent. This was one of the first, if not the first, of this type of mill to be used in the grinding of clay on the Pacific coast. The pulverizer consists of a die-ring, lying in a horizontal plane, enclosed in a sheet-iron housing. A vertical shaft supports a spider from which five rolls are suspended in such a way as to always have them bearing on the die-ring. The vertical mill shaft is driven by means of beveled gear and pinion from a horizontal shaft which is connected by belt with a 60-hp. motor with suitable pulleys to give a speed of 175 r.p.m. A large fan which has a speed of 1100 r.p.m. and is belt connected to a 40-hp. motor is connected to the mill housing. The discharge end of the fan is in turn connected to a cyclone dust collector.

Jan 1, 1929

By A. E. Nehrenberg

IN an earlier publication' it was shown that the.. shape assumed by a volume of growing austenite is inherited from the prior structure. The matrix grains of pearlitic microstructures are equiaxed, and austenite grows in an equiaxed manner in these prior structures. Martensite and bainite, on the other hand, have an acicular grain structure, and the austenite produced in such structures grows in an acicular manner. In the discussion of this paper' it was pointed out that in cold-rolled tempered martensite, austenite grows in an equiaxed, rather than an acicular manner. The results of an experiment carried out to arrive at an understanding of this behavior are illustrated by the micrographs. Fig. 1 shows the acicular microstructure produced by heating tempered martensite to a temperature within the Ac1-Ac3 range, 1350°F. When tempered martensite is cold rolled, then heated to the same temperature, the equiaxed structure shown in Fig. 2 is produced. A sample of cold-rolled tempered martensite heated at 1350°F just long enough for the formation of a small amount of austenite is shown by Fig. 3 to have an equiaxed (recrystallized) ferrite grain structure. The small particles of. austenite which formed at 1350°F in the equiaxed ferrite matrix are likewise equiaxed. Thus, the equiaxed growth of austenite in cold-worked tempered martensite is not a contradiction of the principles described in the previous paper, for the growth pattern reflects the matrix grain structure existing at the time of austenite formation. References A. E. Nehrenberg: The Growth of Austenite as Related to Prior structure. Trans. AIME (1950) 188, pp. 162-174; Journal of Metals (January 1950). 2 J. R. Vilella and R. A. Grange: Discussion of ref. 1. Trans. AIME (1950) 188, pp. 1378-1381; Journal of Metals (November 1950).

Jan 1, 1953