Search Documents

By Louis A. Carapella, William E. Shaw

Magnesium and its alloys have long been characterized as possessing limited capacity for mechanical forming at atmospheric temperatures prior to rupturing despite their outstanding performances in this respect at elevated temperatures. Responsible for this behavior are the fundamental facts that these hexagonal-type metals have comparatively few slip elements at low temperatures for any extensive deformation and that, at high temperatures, additional slip elements become operative, thus enhancing greater plasticity under strain. The transitionai point has been set at 2 25°C by Schmidl for single crystals, and at 250°C by Morel1 and Hanawalt² for extruded magnesium metal. In a recent X-ray investigation on poly-crystalline magnesium-alloy sheets, Barrett and Haller3 have revealed that, below the transitional tempelature, the initial plastic deformation proceeds mostly by a twinning action; that, above such a temperature, the action is mostly by slip. The deep-drawing performance of the magnesium + 1.5 pct alloy sheet† over a wide range of temperatures has been investigated by Weber and Vanden Berg,' and their results are presented in Fig I. It should be noted from this work that a maximum drawability of about 25 pct at room temperature has been obtained on this alloy under the conventional deep-drawing operations. For the same alloy, it is now possible to augment the cold drawability to about 40 pct by a process to be disclosed. Hitherto, this value has been obtained only by deep-drawing the alloy at around 230°C. That greater plastic flow is attainable at atmospheric temperatures on magnesium under certain deformational techniques was discovered by the authors6 in their analyses of plastic-deformational behaviors of pure magnesium. This fact is best illustrated in Fig 2 from the Har-greaves analysis6 performed by the authors under two different modes of loading. For direct test, a separate unstrained specimen was used for each load duration, whereas for the integrated test the same specimen was employed for all the five intermittent loadings so that the load duration was made additive throughout the investigation. The higher plastic flow-rate at room temperature, as designated by the Har-greaves constant S, was obtained by the integrated or intermittent loading procedure. The authors6 in further tests showed that, under such a procedure greater plastic flow was also realized with a progressive increase in deformatione 1 loads. These findings have been applicd

Jan 1, 1947

By William E. Shaw, Louis A. Carapella

Magnesium and its alloys have long been characterized as possessing limited capacity for mechanical forming at atmospheric temperatures prior to rupturing despite their outstanding performances in this respect at elevated temperatures. Responsible for this behavior are the fundamental facts that these hexagonal-type metals have comparatively few slip elements at low temperatures for any extensive deformation and that, at high temperatures, additional slip elements become operative, thus enhancing greater plasticity under strain. The transitionai point has been set at 2 25°C by Schmidl for single crystals, and at 250°C by Morel1 and Hanawalt² for extruded magnesium metal. In a recent X-ray investigation on poly-crystalline magnesium-alloy sheets, Barrett and Haller3 have revealed that, below the transitional tempelature, the initial plastic deformation proceeds mostly by a twinning action; that, above such a temperature, the action is mostly by slip. The deep-drawing performance of the magnesium + 1.5 pct alloy sheet† over a wide range of temperatures has been investigated by Weber and Vanden Berg,' and their results are presented in Fig I. It should be noted from this work that a maximum drawability of about 25 pct at room temperature has been obtained on this alloy under the conventional deep-drawing operations. For the same alloy, it is now possible to augment the cold drawability to about 40 pct by a process to be disclosed. Hitherto, this value has been obtained only by deep-drawing the alloy at around 230°C. That greater plastic flow is attainable at atmospheric temperatures on magnesium under certain deformational techniques was discovered by the authors6 in their analyses of plastic-deformational behaviors of pure magnesium. This fact is best illustrated in Fig 2 from the Har-greaves analysis6 performed by the authors under two different modes of loading. For direct test, a separate unstrained specimen was used for each load duration, whereas for the integrated test the same specimen was employed for all the five intermittent loadings so that the load duration was made additive throughout the investigation. The higher plastic flow-rate at room temperature, as designated by the Har-greaves constant S, was obtained by the integrated or intermittent loading procedure. The authors6 in further tests showed that, under such a procedure greater plastic flow was also realized with a progressive increase in deformatione 1 loads. These findings have been applicd

Jan 1, 1947

By G. R. Wilms

In a recent investigation1 on the properties of chromium, and of Cr-10 wt pct W and Cr-5 wt pct Mo alloys at elevated temperatures, it was found that intercrystalline cavities developed in all of these materials during tensile creep at 950°C, and that the cavities led to intercrystalline fracture. There were some interesting differences, however, between the cavities produced in the pure metal and those in the alloys; these differences, moreover, were associated with a difference in ductility. The relevant conditions of creep testing are specified in the captions to Figs. 1 and 3. Chromium showed the presence of quite large intercrystalline cavities, Fig. 1, and these were more or less randomly distributed around the boundaries. The chromium alloys, on the other hand, showed the presence of both small cavities and cracks at the grain boundaries, Fig. 3; it is apparent that the cracks are formed by the linking together of the small cavities. Moreover, the cavities and

Jan 1, 1960

By J. L. Martin, W. M. Campbell

A new electric logging method, called displacement logging, often gives a direct indication of the presence of mobile hydrocarbons in hydrocarbon-bearing formations. This method is based on the detection of a bank of connate water which is formed between the invading mud filtrate and virgin formation fluids in these cases. The existence of this phenomenon has beer, verified by laboratory studies and by actual field logs taken in known oil sands. INTRODUCTION During the past decade increasing use has been made of conventional electric logs to determine the amount of oil or gas in formations traversed by a borehole. This determination requires knowledge of several factors, such as true resistivity of the formation, formation factor, and water resistivity. Sometimes all of the factors necessary to make a reliable saturation calculation are not available. Also, the computations and corrections which are necessary in such a study often require the services of an experienced log analyst. It has long been the desire of exploration people to have a logging device which will locate hydrocarbon-bearing formations directly without requiring complex interpretation methods. The displacement log, while not completely fulfilling this desire, appears to be a Step in that direction. Basis for the Device The basis for this device stems from a phenomenon which occurs when mud filtrate invades a formation which contains displaceable hydrocarbons. As the mud filtrate invades the formation, most of the oil or gas is pushed out of the invaded zone, leaving residual oil. However, in addition to displacing most of the oil or gas, the connate water is also swept out, since the originally irreducible water is mobile in the presence of a water phase.1,2,3 Tonsequently, this irreducible water piles up as a bank between the virgin oil zone and the invading filtrate. If the mud filtrate is of higher resistivity than the formation water— as is commonly the case—the resulting annular zone, containing the bank of formation water, will be of lower resistivity than either the virgin oil-bearing formation resistivity or the invaded zone resistivity. This resistivity configuration, going from high to low to high again as the distance from the borehole increases, is found only in those zones which contain displaceable hydrocarbons. A device which would reliably detect this low resistivity zone would give a direct indication of mobile hydrocarbons. Illustrations This phenomenon is illustrated in Fig. 1 and 2. Fig. 1 shows a sketch of a zone containing salty connate water plus displaceable hydrocarbons, along with graphs showing fluid content and electrical resistivity vs distance from the borehole, before invasion occurs. Fig. 2 shows this zone, together with fluid content and resistivity graphs. after invasion by a fresh water mud. The resistivity pattern on moving away from the borehole is high: low: high. The absence of the low zone phenomenon in water zones is illustrated in Fig. 3 and 4. Fig. 3 shows a sketch of a zone containing salty formation water and residual oil, along with graphs showing fluid content and electrical resistivity vs distance from the borehole, before invasion occurs. Fig. 4 shows this water zone, together with fluid content and resistivity graphs, after invasion bv a fresh water mud. In this case the resistivity pattern on moving away from the borehole is high: low since there is no change in water saturation at the head ol

Jan 1, 1956

By Jaakko Kajamaa

Neutron diffraction was applied to determine sheet textures by the transmission method. Cold-rolled and recrystallized copper sheets were investigated. The amount of cube texture was determined for three compositions, in which the phosphorus content was, respectively, 0, 0.005, and 0.03 wt pct. The heat treatment was in every case 8 sec at 650°C. In the two latter cases the cube texture was prevented. In addition a comparison with the X-ray diffraction transmission method was made with the 96 pct cold-rolled copper sheet. Outer parts of both (111) pole figures can be considered to be rather identical. This is seen from the fact that the intensity ratio ITD/120" was 0.45 for neutron diffraction and 0.40 for X-ray diffraction. Differences between the methods were discussed in detail. Features peculiar to neutron and X-ray diffraction in texture studies were listed and compared. In this work neutron diffraction was applied to determine sheet textures. Specifically, it was desired to ascertain whether this method can be used to reveal differences when compared to other methods. In addition, the amount of the cube texture in copper sheets was determined as a function of phosphorus content. Previous applications of neutron diffraction to texture problems include the following: nickel wires,' wire of some bcc metals,' and uranium bars.3 In the neutron diffraction technique the greatest difference is in the sample—its method of production and its volume. A sample needs no treatment and its volume is roughly 105 times larger than the volume of an X-ray diffraction sample. The cold-rolled sheet was investigated both by neutron diffraction and by X-ray diffraction, because it is expected that, due to large number of defects, possible differences in the results of the two methods would be revealed. It is a well-known fact that X-ray lines show broadening when cold-worked. Analysis has shown that this is based chiefly on small crystalline size, micro-stresses, and/or faults.4'5 Neutrons are sensitive to the above-mentioned disturbing factors as well, but circumstances in diffraction are different from the X-ray case. Because the sample represents a larger volume, the result is an average over that volume. In addition, it can be assumed that the sample has preserved its original structure, because it needs no special preparation. The particular limitation of neutrons is the relatively low neutron intensity available from nuclear reactors. This decreases the resolution as compared to the X-ray diffraction methods. Furthermore, absorption mainly reduces diffracted X-ray intensity, while multiple scattering effects, i.e., secondary extinction, disturb neutron diffraction. SO neutrons and X-rays behave in a different way when interacting with matter. As in other structural investigations, one can utilize this difference in texture studies as well. One cold-rolled and three recrystallization textures in copper sheets were investigated by neutron diffraction. The samples were produced at the Outokumpu copper factory to the specifications shown in Table I. The paper is divided into five parts. The first deals with the theory of the measurement. In the second, experimental procedures are described. Results are presented in the third part. Both cold-rolled and re-crystallized samples are studied. Discussion is in the fourth part, and finally in the fifth part some conclusions are drawn. 1) THEORETICAL CONSIDERATIONS Properties peculiar to neutron diffraction are the following: a) the scattering length varies greatly between one element and another; b) many of the elements do not absorb neutrons appreciably. In this connection it is of primary interest to know the interaction of neutrons with lattice imperfections. As with X-rays this problem leads to diffraction analysis of deformed and recrystallized metals. From the physical point of view the main difference is that neutrons are scattered by nuclei (magnetic scattering is not considered here), whereas X-rays are scattered by electrons. The features peculiar to neutron and X-ray diffraction methods in texture studies are listed in Table 11. Pole figures are an important tool in performing structural analysis of deformed or recrystallized metal. Present texture research technology requires pole figures which are as precise as possible. The choice between these two methods depends on the technical information which is required. The X-ray diffraction transmission technique may give results which are not necessarily representative of the average physical state of the sample. Although foil samples normally contain enough crystallites for diffraction, they may not necessarily represent the whole structure. An example of this problem is the frequently observed difference between the "surface" and the "inside" texture of a sample. The production of foil samples may disturb the original structure of the parent material. The selection and orientation of the foil from the sample is quite arbitrary. Normally, a highly deformed piece of metal has several texture components. Different components are deformed in a slightly different manner. This is a re-

Jan 1, 1969

By AIME AIME

Council.* PRESIDENT OF THE COUNCIL. ROBERT Wm. HUNT CHICAGO, ILL. (Term expires February, 1907.) VICE-PRESIDENTS OF THE COUNCIL. WILLIAM P. BLAKE TUCSON, ARIZ. THOMAS F. COLE DULUTH, MINN. IRVING A. STEARNS WILKES-BARRE, PA. (Term expires February, 1907.) HENRY M . HOWE NEW YORK, N. Y. J. B. GRANT DENVER, COLO. JAMES D. HAGUE NEW YORK, N. Y. (Term expires February, 1909.) COUNCILORS. F. L. GRAMMER BALTIMORE, MD. JOSEPH HARTSHORNE POTTSTOWN, PA. CHARLES H. SNOW NEW YORK, N. Y. (Term expires February, 1907.) A. A. BLOW WASHINGTON, D. C. FRANK LYMAN NEW YORK, N. Y. T. A. RICKARD SAN FRANCISCO, CAL. (Term expires February, 1908.) THEODORE DWIGHT NEW YORK, N. Y. WALTER WOOD PHILADELPHIA, PA. WM. FLEET ROBERTSON VICTORIA, B. C., CAN. (Term expires February, 1903.) SECRETARY OF THE COUNCIL. R. W. RAYMOND, No. 99 John Street NEW YORK, N. Y. (Term expires February, 1907.) ASSISTANT SECRETARY AND EDITOR. JOSEPH STRUTHERS NEW YORK, N. Y.

Mar 1, 1906

THE paper on "Cross-cuts in Coal Mining," by J. J. Rutledge (published in MINING AND METAL-LURGY, February, 1927, p. 64) was brought up for discussion at the annual meeting, where the follow-ing comments were made T. D. Thomas (Lehigh Coal & Navigation Co., Lansford, Pa.) : This question has caused me a lot of worry, not in the particular district in which I am, but throughout other districts. There are always several angles to consider. If you are in a hurry to push development work, you might increase the distance between cross-cuts from 60 to 350 ft., but if you have a 40-ft. chain pillar every 60 ft. it will cut down your entry driving a whole lot. Looking at it from the ventilation angle, I agree that too many cross-cuts in entries are bad things. You have a tremendous amount of leakage, and I have seen currents starting out with 45,000 cu. ft., and after passing about 30 or 40 cross-cuts the current has dwindled down to about 18,000 or 15;000 cu. ft. The result is that the question of putting in auxiliary fans is raised. That involves several points into which I do not want to go too far, but I am in favor of not getting in too many cross-cuts, putting them in only where they are necessary: I think the state mining laws are wrong in a number of places on that, and that when you finish with a cross-cut it should be in the room. It should be well sealed on an entry. There are several ways of tightening up the cross-cuts so as not to have the great amount of leakage and wastage of: air that we now have. 'I prefer tile stopping; other people prefer cement or brick, but there is a big fac-tor to all mines, saving the mine. I checked up on the number of fans in the anthracite region and found there are 651. That was derived from the state report of 1921, and it enabled me to compute from the power the weight of the air. In the anthracite region of Pennsylvania we put in 9 tons of air to every ton of coal we get out. Tracing that back again and taking the Government's figures which they made some time ago, I found but 20 per cent of the air got to the faces where it was actually needed. That is a tremendous big loss and shows a possibility for saving, money for the various coal companies. Chairman Rice: I think what Mr. Thomas refers to was an investigation by R. Y. Williams, of the Bureau of Mines in Illinois, where a study was made of 100 typical mines, and, speaking off-hand, my recollection is that we found as little as 15 per cent of air reached the faces in one of the mines and another was as much as 50. That seems to be a reflection on the type of stoppings and general ventilation scheme.

Jan 3, 1927

By A. F. Taggart

This paper describes the result of a series of experiments run in the laboratory of the School of Mines, Columbia University, during the winter of 1927-28. It shows that the several operating adjustments of a pneumatic table produce effects in the action of a given coal that may be grouped into two classes, viz.: stroke length, speed and rocker-arm angle, which affect longitudinal travel; air supply and table slope (transverse and longitudinal), which determine transverse travel. The magnitude of the effect of the different adjustments varies. Some of the adjustments affect stratification of the bed, both as respects size and specific gravity of the bed components, as well as direction of travel. Operation of a pneumatic table is fundamentally different from that of a wet table in that the former exerts, through the air supplied, a force on the particles upward away from the deck which is lacking on the wet table while, on the other hand, it lacks the positive control over cross travel that is supplied by the wash and feed water. Apparatus The pneumatic table used is shown in Fig. 1. Deck A is 20 by 12 in. and consists of nainsook supported on slats that register with the riffles. Fig. 2 is a photomicrograph of the nainsook used. It shows that the cotton threads average about 0.13 mm. dia. and the apertures about 0.17 mm. The deck carries 12 riffles consisting of wooden strips, 3/16 in. wide and 1/4 in. high, laid parallel to the feed side of the table. The riffles terminate along a line starting on the feed side at a point 11 in, from the mechanism end and running to the corner formed by the coal side and slate end. Taper starts from a line that runs parallel to their terminal line through the junction of the upper riffle with the mechanism end. The height at the terminal line is about 1/32 in. The deck with its supporting slats is carried on a framework consisting of rails A, sloping end rails B, and adjustable metal strips C, which latter permit variation in transverse slope. This frame is enclosed at the edges by means of heavy canvas, indicated in the sketch by wavy lines, which makes a flexible conduit between the deck and the stationary air chamber,

Jan 1, 1930

By Henry N. McCarl

[The Construction Materials section contains the following Chapters: Aggregates Cement and Cement Raw Materials Crushed Stone Dimension and Cut Stone Lightweight Aggregates Gypsum and Anhydrite Sand and Gravel Insulating Materials-Thermal and Sound Slag Roofing Granules] Mineral aggregates are those natural and manufactured industrial mineral and rock materials that provide bulk and strength in portland cement concrete, bituminous concrete mixes, and plaster or stucco surfaces. They may also provide special characteristics such as thermal and acoustical insulation, weight, surface textures, abrasion resistance, and impermeability to various concrete products and mixes. Most aggregates are relatively inexpensive materials, but despite their low unit value, the tonnages consumed each year in the United States and throughout the" world make mineral aggregates by far the leading industrial mineral and rock materials both in terms of volume (tonnage) produced and value consumed. The major use of mineral aggregates is in concrete. The low cost, high bulk aggregates tend to keep concrete construction costs at levels competitive with other building materials. Other major uses of aggregates include highway and railroad base or ballast materials, graded fill, and various industrial uses such as metallurgical and chemical fluxes and raw materials-these latter uses are often considered nonaggregate uses of mineral aggregate materials. The per-ton value of mineral aggregate materials at the production plant in 1980 and 1981 varied from $2 to $5 for most sand and gravel and crushed stone, $3 to $6 for air-cooled slag, $7 to $20 for expanded slag and expanded clay or shale aggregate, to as much as $165 to $320 for expanded perlite or vermiculite. The expanded lightweight aggregates have been dramatically affected by increasing fuel costs. It is ironic that the specialized aggregates used as insulating materials to conserve energy cost so much more to produce due to the high proportion of energy consumed in their production. The first four parts of "Construction Materials" deal with the utilization of four major mineral aggregate types: Crushed Stone, Lightweight Aggregates, Sand and Gravel, and Slag. While the focus will be on the use of these industrial minerals and rocks, there will also be some coverage of sources, mining and production, especially in those cases where they are not discussed in the Commodity section of this book.

Jan 1, 1983

By Henry Howe

(New York Meeting, February, 1913.) THE transformation which steel undergoes in glow cooling, from the condition of austenite when above the transformation range into that of pearlite plus either ferrite or cementite below that range, is subject to great lag. This transformation is essentially the pearlitizing of the austenite. Indeed the hardening of steel is due to this lag, which is made so great by extremely rapid cooling that a very large part of the transformation itself is restrained, so that the rapid cooling catches the metal in an only partly transformed state, that of martensite, and under favorable conditions even in an almost wholly untransformed state, as in the cases of Maurer's austenitic manganese steel. Hadfield's austenitic manganese steel, 25 per cent. nickel steel, and other austenitic alloy steels, are austenitic even after slow cooling. It has long been known that this- lag increases (1) with the rapidity of cooling, (2) with the presence of certain retarding elements, notably manganese and nickel, and (3) with the temperature from which cooling starts. The present inquiry touches the last. of these influences, but incidentally it throws light on the first also. This influence of higher heating in increasing lag manifests itself in different ways which, though they may at first seem unrelated, are in fact but different, aspects of one and the same thing. Thus, among heatings to different high temperatures, all of them above the transformation range, the higher the temperature to which the steel is heated (1) the lower is the temperature it which the transformation occurs in cooling slowly down, (2) the shorter is the time occupied in the actual cooling from above the transformation range to the room temperature under given external conditions, whether of slow or

Jan 3, 1913

By D. E. Stephenson. Discussion by R. G. K. Morrison, L. Obert

R. G. K. Morrison (Chairman, Dept. of Mining Engineering and Applied Geophysics, McGill University, Montreal, Que., Canada) - The discing of drill core has been a recognized pressure phenomenon for many years but only recently has an interest been taken in the mechanism involved. The work of Jaeger and Cook is referred to in the text. The authors have now advanced the study to establish, within certain loading limitations, a direct relationship between axial and radial stress at failure. This is an important contribution. In mines generally, where pressure conditions result in the spalling of openings, the faces of drifts and crosscuts, on scaling, usually show a concavity with respect to the opening very similar to the face of the drill hole after the separation of the stub. The same holds for shaft sinks. This suggests a similarity between the mechanism of the discing of core and that of the spalling of an opening, under pressure, to develop a more stable outline. The latter, commonly regarded as shear, is the most conspicuous type of failure observed in

Jan 1, 1967

F. AT. FARMER*, New York (written discussion?)- The paper presents many phases of the welding art concerning which there are very divergent views. In many cases, the wide differences of opinion are based on the results of mechanical tests, but an examination of the mechanical test data discloses a wide variation in character of the tests made and in the details of procedure, so that it is frequently not only difficult to analyze and check the basis of the conclusions but impossible to correlate various groups of test results. It would seem, therefore, that the technique of testing welds is one of the phases of the welding art that should be studied and standardized in order that the results of mechanical tests made by different people may be strictly comparable and have the same significance to all. The vital difference between testing a specimen of steel that includes a welded joint and testing an ordinary specimen is the non-homogeneity of the weld specimen. The weld specimen has at its center a section composed of material that usually has physical, chemical, and metallurgical characteristics distinctly different from the adjoining metal. Furthermore, the section of added metal is more or less irregular and the ratio of added metal to original metal in the section is quite variable. Consequently the details of procedure and of recording data should be more minutely prescribed than in the testing of ordinary specimens. A conspicuous example f a mechanical test that requires standardization is the cold bending test, a standard test for mild steel. With the usual method, the specimen is bent around. a pin of prescribed diameter and, as all specifications usually require bending to 180° without fracture, the manner of applying the load is immaterial because the specimen is ultimately completely wrapped around the pin. But a specimen containing a welded joint at the center will usually not withstand bending to 180° because of the much lower ductility of the deposited metal in the weld. It is therefore obvious that the farther apart the points of support are the greater will be the angle attained before cracking occurs, simply because most of the bending will take place in the original metal. It is therefore highly desirable that there be prescribed a standard test that fixes exactly the distance between the supports, the curvature of the surface of supports, and the relation between this curvature, that of the loading surface, and the thickness of the specimen.

Jan 5, 1919

By J. H. Smith, H. W. Paxton

ALTHOUGH many structural and kinetic investigations have been made for alloys of iron and nickel, only meager data exist from thermodynamic investigations. The purpose of this note is to estimate the free energy of the Fe-Ni solid solutions from thermodynamic data available for ternary alloys containing iron and nickel. The lack of a description of the thermodynamic behavior for the Fe-Ni system has required the structural and kinetic analyses of the system to assume some form of solution behavior, usually regular, e.g., the mar-tensite transformation analysis of Kaufman and Cohen, 1 consistent with the limited thermodynamic data. Indications that this system could exhibit ideal solution departures might have been suggested by the large deviations from additivity rules observed in the density and lattice-parameter measurements of Jette and Foote2 who interpreted this in terms of possible solute-solvent interactions. Later Turkdogan et al. 3 and more recently Ward and wright 4 found a minimum in the graphite solubility in liquid Fe-Ni solutions near the concentration of FeNi3 with deviations from linearity persisting at all concentrations. This was interpreted by Ward and wright4 to indicate negative heats of solution and was suggestive of short-range ordering. The infinitely dilute activity coefficient of carbon (?oC) was also observed by smith5 to pass through a maximum near the FeNi3 concentration in Fe-Ni solid solutions. Recent investigations of the liquid solutions over the entire concentration range by Zellars et a1.' and Speiser et a1.," using vapor-pressure determinations, revealed both negative departures from Raoult's law and a nonregular solution behavior. The solid alloys have been studied by Oriani 8 and Kubaschew-ski and von Goldbeck6 employing gaseous H2/H2O equilibria with Fe and FeO. Both investigations were in substantial agreement, indicating very small departures from ideality. However, Oriani observed the formation of Fe3O4 (instead of FeO) at XFe= 0.441 which severed the equilibrium and precluded experimental investigation of the nickel-rich alloys. Heat-capacity and heat-content measurements have been evaluated by Montgomery10 and found generally unsatisfactory for gleaning thermodynamic information. This is due to the unknown final states of the alloys caused by the interference of the martensite transformation on cooling iron-rich concentrations and superlattice formation, magnetic transformation, and the varied heat treatments used by investigators of nickel-rich concentrations. As an alternative to the experimental difficulties, indirect estimates of the solid-solution behavior have been made by Fleischer and Elliott11 and Smith et a1.12 From their measurements of the solubility of Fe-Ni alloys in liquid lead, Fleischer and Elliott calculated the nickel activity (aNi) (and integrated for aFe) by assuming: 1) liquid lead has no solubility in solid Fe-Ni alloys, 2) Henry's law is obeyed throughout the liquid lead-rich phase (0— 12 at. pct Nil, and 3) Henry's law constant is independent of relative iron and nickel concentrations. The estimate of Smith et a1.12 was obtained

Jan 1, 1964

NEW MEMBERS The following list comprises the names of those persons who became members during the period of June 10, 1917, to July 10, 1917. BANKS, LEON MAXWELL Agent 3. Supt., Grant Leasing Co. Metcalf Ariz. BEAUCHAMP, HENRY CLAY : Mine Operator, Sisson, Siskiyou Co., Cal. BOCKING, CHARLES, Asst. Mgr., Butte & Superior ,Mining Co., Rialto Bldg., Butte, Mont. BEYER, HERMAN E., Chief Engr., Condenser Dept., Ingersoll-Rand Co., 11 Broadway, New York, N. Y. BLACK, HERBERT F 1512 Oliver Bldg., Pittsburgh, Pa. BRENNAN, PATRICK J., Gen'l. Supt., Elkhorn Division, Consolidation Coal Co., Jenkins, Ky. BUTNER, DANIEL W., Chem. & Supt., Underground Min., Spanish American Iron Co., Daiquiri, Santiago de Cuba, Cuba. CARLTON, DAVE P Nevada-Douglas Cons. Copper Co., Ludwig, Nev. DE AROZENA, JOE Min. Engr., 321 Preusser St., San Angelo, Texas. DICKIE, CHARLES HERBERT, Pres., Georgia River Min. Co., Duncan, Vancouver Island, B. C., Canada. DOBBINS, WALTER Mill Foreman, Chino Copper Co., Hurley, New Mexico. DRURY, CHARLES W., Asst. Professor of Met., Queen's University, Kingston Out. Canada.

Jan 8, 1917

By Henry M. Howe

The transformation which steel undergoes in slow cooling, from the condition of austenite whelk above the transformation rage into that of pearlite plus either ferrite or cementite below that range, is subject to great lag. This transformation is essentially the pearlitizing of the austenite. Indeed the hardenillg of steel is due to this lag, which is made so great by extremely rapid cooling that a very large part of the transformation itself is restrained, so that the rapid cooling catches the metal in an only partly transformed state, that of martensite, and under favorable contditions even in an almost wholly untransformed state, as in the cases of Maurer's austenitic manganese steel. Hadfield's austemtic. manganese steel, 25 per cent. nickel steel, and other anstenitic alloy steels, arc austenitic even after slow cooling. It has long been known that this lag increases (1) with the rapidity of cooling, (2) with the presence of certain retarding elements, notably manganese and nickel, and (3) with the temperature from which cooling starts. The present inquiry touches the last of these influences, but incidentally it throws light on the first also. This influence of higher heating ill increasing lag manifests itself in different ways which, though they may at first seem unrelated, are in fact hut different aspects of one and the same thing. Thus, among heatings to different high temperatures, all of them above the transformation range: the higher the temperature to which the steel is heated (1) the lower is the temperature at which the transformation occurs in cooling slowly down, (2) the shorter is the time occupied in the actual cooling from above the transformation range to the room Temperature under given external conditions, Whether of slow or

Jan 1, 1914

[ ] Granville S. Borden (Mining Taxation, P. 1049) has written two other published articles on the subject, Taxation and Mineral Resources, and An Income Tax Program for Mineral Producers. Both articles appeared in Mining Engineering. He is presently employed by Standard Oil Co. of California as a special tax counsel. He holds an LL. B and an LL. M from George Washington University and a Bachelor of Science in Mining from the University of California. He has been chairman of the Taxation Committee of the Minerals Economics div. of the AIME. Borden fishes, plays golf, prospects, and performs mineral analysis as hobbies. [ ] Charles C. Towle (co-author, Uranium Deposits of the Grants District, New Mexico, P. 1037) graduated from the Colorado School of Mines with a degree in Geological Engineering. He was a member of Sigma Nu; Theta Tau, an honorary professional society; Blue Key, honorary social society; the glee club and quartet, and a member of the student council. He has been a mucker, driller, flotation operator and mill shift boss for the Clear Creek-Gilpin Co., Idaho Springs, Colo.; Geologist, chief engineer, and chief geologist for Patino Mines & Enterprises Consolidated, Inc., Bolivia; appraisal engineer and part-time geology student, Denver; office geologist for Geology Dept., special Engineering div., Sea Level Canal Studies, Panama Canal; and geologist, div. of Raw Materials, USAEC, Grand Junction, Colo. He is currently chief of the Denver Exploration Branch, div. of Raw Materials, USAEC, Denver. Towle was at one time a tournament golfer, playing three and four times a week. While working in South America he played in numerous tournaments. Today, although playing only occa sionally, he shoots in the low eighties.

Jan 1, 1952

By DR. RICHARD RATHBUN

(Washington Meeting, May, 1965.) THE remarks of Dr. Rathbun in his address of welcome render it unnecessary that I dwell either upon the history or aims of the National Museum, and enable me to proceed at once with a brief descriptive outline of the Department for which I am responsible, and this with particular reference to that division devoted to applied geology. The amount of geological material brought together prior to 1876, under the various Congressional acts quoted, was, though valuable, comparatively small. It consisted mainly of the collections made by Professor J. D. Dana and his assistants during the Wilkes Exploring Expedition; by the various geologists accompanying the surveys of the Pacific railroads in 1854-55; the Surveys West of the 100th Meridian under the direction of the Engineering Corps of the Army; the United States geological surveys under direction of Dr. F. V. Hayden ; and the various Land Office surveys. Prior to 1873 there were no paid assistants to care for these collections. They were studied, if studied at all, by " collabrators," so-called, several of whom had offices and even sleeping apartments in the Smithsonian Institution. In the list of these collaborators are found such names as Conrad, Cope, Gabb, Leidy, Lesquereux, Meek, and Newberry. The building now occupied by the National Museum was designed primarily to make room for the great mass of material secured in 1876 at the close of the Centennial Exposition in Philadelphia. As completed in 1880, it afforded opportunity for expansion and incidental organization on much more practical basis than had previously existed. This found expression in the creation of numerous departments with salaried officials to take charge of the various collections. With the appointment of Dr. George W. Hawes to the position of Curator of Geology and Mineralogy, in 1881, and Dr.

Jul 1, 1905

By Edward A. Loria

Vanadium is one of the materials being considered for use in fast-breeder nuclear reactors. It is a good heat conductor and nearly transparent to radiation, properties regarded as ideal for nuclear fuel containers. The problem has been the metal lacks ductility needed for forming. In our program at Reno Laboratory the effects of the U.S. Bureau of Mines (previous affiliation) the effects of oxygen, nitrogen, and carbon have been reported21,22 nd most recently the effects of boron and boron with carbon.23 The continuing study by the Ames Laboratory of the effects of hydrogen, the most subtle and fugitive element in its relationship to structure and properties, is commendable. The solubility of oxygen, nitrogen, and hydrogen in vanadium (and other bcc metals as well) is related to material purity. With the available limit on metal purity and the interaction (clustering) of hydrogen with the other interstitial and substitutional elements present in their base metal, would the authors comment on the tolerance of hydrogen in relation to oxy- gen that will avoid intergranular fracture and above what content or how seriously harmful in oxygen at various carbon levels? Understanding the true effects of hydrogen (and other interstitial impurities) in vanadium depends on knowledge of the amount present under various conditions and its distribution between various possible positions. Significant amounts of hydrogen may be in "thermo-dynamic" solution, but not as individual atoms in interstitial positions. It may be in grain boundaries, in subgrain boundaries, in vacancies, or in dislocations. Some of the hydrogen may be paired or in complexes with impurities in substitutional solid solution in vanadium. This makes the analysis of the effect of hydrogen vastly more difficult. It should not be expected that hydrogen in grain boundaries will affect slip in the same manner as hydrogen in interstitial positions, nor will the complexes react to heat treatment the same way as hydrogen in dislocations. It is gratifying that the authors have quoted results from two of our inestiations,' but neglected one2' which applied the Petch theory to electrorefined vanadium of high purity and analyzed the effects of oxygen, nitrogen, and carbon on the ai and ky values obtained by the extrapolation and grain size methods. Details can be found in the paper. Briefly, we obtained a ui value of 10,300 psi (t = 5150 psi) at 273°K. The metal also exhibited profuse twinning with high ductility at 123" and 77°K. Nitrogen was more effective than oxygen in increasing ui, the increase being about twice as much for the same impurity level. Carbon additions resulted in only minimal changes in Ui. The corresponding ky increased as oxygen and nitrogen increased, with nitrogen being more effective. Carbon additions resulted in little change. Although the difference in yield strength of vanadium was explained on the basis of the Cottrell-Bilby model of the tearing away of dislocations from the impurity atoms,

Jan 1, 1970

By Marc Lemieux

Computer pit design techniques generally make use of models in which the deposit is represented by a regular array of data. Using a regular system, the number of data points required to represent the air, waste and mineralization in a large deposit become excessive. The number of blocks used to describe the deposit is dependent upon the block size. The quality of the pit wall slope design also is dependent upon the block size used and the method of defining the slope. The error associated with reserve calculations becomes greater with increasing block size. A deposit model consisting of variable sized air and mineralized blocks has been developed at the University of British Columbia and improved upon at Climax for pit design work. The method permits put- ting the entire model in core for rapid data processing. This permits the use of a versatile cone generation technique which allows close adherence to variable slope constraints in all directions. The conical shape is approximated by rectangles on each level which equal the area of the ideal conical intersection. The shape of the intersection may vary from approximately circular to elipsoidal. The approximate cone shape is controlled by the slope constraints applicable at the point of intersection on the bench. The overall modeling technique greatly assists the pit design engineer in developing a high quality pit design.

Jan 1, 1977

R. M. Raymond, New York, N. Y.—The filling and drawing down of the overhead material was done at considerable depth, which is not the usual method in which it starts at the surface.. R. J. Mechin.— It is a little more than 1000 ft. at El Bordo. The vein above had been caved practically to the surface and some of the ore had been excavated, using underhand and overhand square-set methods. This was far enough away from the shaft to prevent any bad effects. When the sill floor was taken out, to insure the old cave material following down well, we put chutes in the square sets for several weeks until we were sure that the material from above was moving down; on each level above, several crosscuts were driven into the old fill by which we could see the material coming down and thus be sure it was following the first. We had to dynamite it very little because it was dry and dusty. The only trouble was that timber starting from the old square sets would get across the chute and hang up. R.. M. Raymond.—HOW many floors did you operate at once? R.. J. Mechin.—We would operate one floor through the whole length and prepare for the second. F. W. SperR, Houghton, Mich.—Could you have worked it in steps? R.. J. Mechin.—Yes; but working it all on one floor was much better for ventilation. The passage between steps would tend to become heavy and blocked and, as the passages from the mining floor down are usually filled with ore, there would be no way for the air to pass up. By means of doors and fans, air was driven to the extreme end of the orebody through the stope and up the other end; but it could have been worked in steps. F. W. SpeRR.—D the following-up material ever become so heavy that you could see weight on the caps before you had to take out the posts?

Jan 1, 1927