Search Documents

By Jean Howard

ALTHOUGH zone melting has found favor in recent years because of its convenience and its faster rate of production of single crystals, the older technique of strain annealing still has a number of advantages. It has been reported1 that the lattice of a crystal prepared in this manner has fewer defects than one grown from the melt and, of course, the control of the external geometry is easier. Also, the diameter of the crystal which can be grown by zone melting has a theoretical limit determined by the surface tension, thermal conductivity, and specific gravity of the material, while the size of that which can be grown in the solid state is limited only by practical considerations. In a program for the study of the structure-sensitive properties of niobium and its alloys it was desirable, for ease of handling, to have available single crystals of large diameter. This requirement dictated the choice of the strain-anneal technique. Induction heating was chosen in the present work in preference to other methods because of its deep penetration of large-diameter sections. A five-turn coil, powered by a motor generator operating at 10,000 cps, is contained in a vacuum chamber. The work is lowered through the coil for both the recrystallization and the crystal-growth steps. Starting with electron-beam melted material, the bars are cold-swaged, recrystallized, strained in a tensile machine, and then subjected to the growth step. Single crystals have been grown under the following conditions: Reduction in area during swaging— 79 to 99 pct, recrystallization temperature—1500o to 1667°C at the rate of 1.25 in. per hr, strain—1.0 to 2.5 pct, growth temperature—1600o to 2400°C at rates from 0.15 to 1.25 in. per hr. Starting grain sizes achieved after the recrystallization step varied from 0.6 to 1.55 mm. The starting grain size was found to be critical; if it is too fine and has any residual cold work, as shown by the presence of a fiberlike texture, a single crystal cannot be grown. Using this technique niobium single crystals have been grown from 0.250 in. diameter and 12 in. long to 1.00 in. diameter and 5 in. long as shown in Fig. 1. The 1-in. crystal is the largest to be reported for a refractory metal as compared to 0.500 in. for molybdenum grown by zone melting.2 As with zone melting, control of orientation is possible by the use of special procedures. Other investigators, see for example Williamson and Smallman,3 have reported that orientation control may be achieved by a bending technique. In the present work the strained rod is partially lowered through the coil to start the growth of the crystal. Then it is removed and bent at a point ahead of the interface between the single and polycrystalline portions. Finally, it is returned to the chamber and growth is continued "around the corner". The amount of bending which can be imparted to the rod is limited by coil geometry which up to now has been 10 deg. However, by repeating the bending and growing operations it should be possible to attain any desired orientation. The perfection of these single-crystal specimens as a function of process variables is being measured by X-ray and metallographic techniques and the results will be reported in a forthcoming paper. This work was partially supported by the Advanced Research Projects Agency.

Jan 1, 1964

By P. R. Kalischer

In the production of alloys by powder metallurgical processes it is often necessary or desirable to include one or more cornponents that tend to form very stable oxides. Included in this group of metals are aluminum, manganese, magnesium, silicon, and a few others. In many cases it is not necessary for the sintered compact to have full density and the other physical characteristics of a cast alloy and in that event no undue precautions need be taken. If, however, it is required that the sintered part be entirely homogeneous, and have maximum density and physical properties, some method must be found to reduce the surface films of oxide, which are always present on the metals, and for the metals mentioned above this is always extremely difficult, if not impossible. since the production of high-density alloys is of particular interest to powder metallurgists, some experiments were undertaken to devise methods of reducing the refractory oxides. For this work, alloys of iron, nickel, and aluminum were chosen because aluminum oxide is one of the most stable oxides and because these alloys in the right compositions form excellent permanent magnets. All of the pertinent properties of the magnets could be accurately and delicately measured by density measuremerits and magnetic tests of sufficient scope to give a complete demagnetization curve. From such a curve the maximum coercive force, residual magnetism, and energy products could be obtained and compared with the same properties for a cast material. Any lack of homogeneity, density, or solid diffusion would be immediately apparent as a decrease in the magnetic properties. Nature and Removal of Surface Barriers The early work of the present investigation was based upon published processes.* In the published information it was claimed that by intimately mixing iron, nickel, and iron-aluminum alloy (50 Per cent Fe, So Per cent Al) powders, compressing such a mixture into the desired shape and size, and then sintering (heating to a temperature below the melting point of the component metals) in hydrogen at 1200°C. or higher, a sound, homogeneous article could be made having the desired physical size, shape, and strength, and good magnetic characteristics. However. this early work showed clearly that something in the powder compress was inhibiting diffusion and the process was almost entirely unworkable. In the initial phase of the investigation samples of iron powder, nickel powder, and iron-aluminum alloy powder were pressed into separate bars and sintered in hydrogen. Both the iron and nickel powders sintered

Jan 1, 1941

By P. R. Kalischer

In the production of alloys by powder metallurgical processes it is often necessary or desirable to include one or more cornponents that tend to form very stable oxides. Included in this group of metals are aluminum, manganese, magnesium, silicon, and a few others. In many cases it is not necessary for the sintered compact to have full density and the other physical characteristics of a cast alloy and in that event no undue precautions need be taken. If, however, it is required that the sintered part be entirely homogeneous, and have maximum density and physical properties, some method must be found to reduce the surface films of oxide, which are always present on the metals, and for the metals mentioned above this is always extremely difficult, if not impossible. since the production of high-density alloys is of particular interest to powder metallurgists, some experiments were undertaken to devise methods of reducing the refractory oxides. For this work, alloys of iron, nickel, and aluminum were chosen because aluminum oxide is one of the most stable oxides and because these alloys in the right compositions form excellent permanent magnets. All of the pertinent properties of the magnets could be accurately and delicately measured by density measuremerits and magnetic tests of sufficient scope to give a complete demagnetization curve. From such a curve the maximum coercive force, residual magnetism, and energy products could be obtained and compared with the same properties for a cast material. Any lack of homogeneity, density, or solid diffusion would be immediately apparent as a decrease in the magnetic properties. Nature and Removal of Surface Barriers The early work of the present investigation was based upon published processes.* In the published information it was claimed that by intimately mixing iron, nickel, and iron-aluminum alloy (50 Per cent Fe, So Per cent Al) powders, compressing such a mixture into the desired shape and size, and then sintering (heating to a temperature below the melting point of the component metals) in hydrogen at 1200°C. or higher, a sound, homogeneous article could be made having the desired physical size, shape, and strength, and good magnetic characteristics. However. this early work showed clearly that something in the powder compress was inhibiting diffusion and the process was almost entirely unworkable. In the initial phase of the investigation samples of iron powder, nickel powder, and iron-aluminum alloy powder were pressed into separate bars and sintered in hydrogen. Both the iron and nickel powders sintered

Jan 1, 1941

By E. T. Dumble

For many years there have been occasional reports of the discovery of gold from a belt of the coast country of Texas which is underlain by deposits belonging to the lower Eocene. For the most part they have been treated as newspaper reports and no examination or record of them has been made. Among such, it may be mentioned that in 1896 there was a flurry over reported gold-discoveries west of Luling and elsewhere in this belt, and in 1903 some prospect-shafts were sunk on the Gon-zales branch of the Galveston, Houston & San Antonio railway, 3 miles below Harwood. During 1912, further discoveries have again brought the matter to our attention, and it may be of interest to record the facts as we have found them. Some years ago specimens were sent me, which were said to have been taken from certain beds on Gazley creek, and concentrated by washing in a rocker. In them were several particles of gold sufficiently large to be visible to the eye. Under the microscope they showed to be, with few exceptions, sharp cornered, and not rounded as is usual with placer-gold. They were not filings, however, but their sharpness seemed rather to be due to a recent freeing from their matrix. One or two grains were rusty, and one copper-hued, but the most of them were tolerably bright. On examining the material of the samples small grains or fragments were found, of a yellowish brown color, which seemed to be of a finely-granular structure—possibly a sandstone. In these fragments I found particles of gold, one of them being large enough to be visible without a lens. Gazley creek empties into the Colorado river just north of Smithville, and for a few miles north of that place its banks show, beneath the deposits of more recent materials, the sands and clays of the Lignitie division of the Eocene, with lignite, shells of iron, etc.

Jan 1, 1913

By -1ng. B. Stampa

Introduction The author investigates the technology available for mine flow reversibility by reversing the operation of the main fans. Air bypassing, reversed sense of impeller rotation, and blade angle overturning are indentified as the most important means of achieving the flow reversibility. The axial flow fan is studied in some detail and the important variables of fan capacity, pressure, and efficiency are compared. Although some references to rotor velocity vectors are made (Fig. 1) the subject is not presented in detail in order to stay within the paper's intent. Background Where applicable, the requirements of mine air reversibility are an important part of the overall mining operation and should be given proper attention during mine ventilation design. The need for preventing mine fires in intake shafts is the reason that, for a long time, it has been a requirement in the Eastern European countries to have the feature of flow reversibility built into all main mine ventilators. In West German coal mines, this requirement does not apply since higher priority is given to safety precautions. Some metal and mineral mines in the United States are required to have ventilation currents readily reversible in order to fight underground fires as stipulated by the Title 30, Mineral Resources, and by the mining laws of some states. From an equipment performance standpoint, assuming the validity of other flow technical data, the question of the ventilator flow reversibility is of ten related to the actual scenario of the begining of an emergency. Most of the time, the system operates within half of the design capacity only and assuming that the equivalent mine orifice is stable only a quarter of the design pressure must be produced by the fan in any event. For such an operating point, the effective gradient and energy losses can be disregarded since fire emergencies usually last for only a short period of time. Equipment Comparison Fig. 2 depicts a ventilation arrangement wherein the flow can be reversed through changing the functional position of the dampers (slideplate or blade type). Both axial or radial fans can be applied in this case. For the mine exhaust operation, slide plates (guillotines) I and I11 are opened while plates I1 and IV are closed. The flow thus encounters two reroutings, which due to the reverse ventilation flow cannot be equipped with proper sheet metal deflectors, and therefore large pressure losses result during the air reroute operation. When the intake operation is considered, the dampers I and I11 are closed and the pair I1 and IV is opened. For this arrangement, almost the same flow conditions exist as for the foregoing exhaust mode; however, one additional corner must be applied. Even if a highly efficient ventilator is used in one of the previously described systems, the additional pressure losses resulting from air rerouting plus those encountered between the planes "0" and "00" significantly affect the overall energy requirements. Illustrated in Table 1 are the relative component losses of even flows for evaluation of various detour arrangements. From the aerodynamics standpoint, when these components are being designed, serious consideration must be given to the individual levels of the pressure loss coefficient, 5. Should there be an increase in the sum of the loss coefficients due to the particular component selection such that, for example, the net change is 1.2; the resulting pressure to be produced by the fan can be calculated from:

Jan 1, 1981

By W. I. Duvall, D. E. Stephenson. Discussion by R. G. K. Morrison

R.G.K. Morrison (Chairman, Dept. of Mining Engineering and Applied Geophysics, McGill University, Montreal, Que. Canada) - The authors have introduced a subject, the intensive study of which has awaited scientific developments. These are now such as to justify a thorough review of our thinking on the causes and control of rockbursts. The formulae developed in the paper, the comparison between rockbursts and earthquakes in figure 1 and the energy data relating to explosives serve as an effective foundation. In the paper this writer is quoted as suggesting that energy of the order of 10 x 10 11 ft. lb. may have been released in some of the heaviest rockbursts in the Kolar Gold Field. He now hastens to add that such an estimate has no scientific validity. It arises only from a casual comparison of surface and underground effects of the medium heavy bursts, referred to in the paper and estimated by Jones at 3.0 x 1010 ft.lbs., with those of obviously greater magnitude. In any case, we have the estimate by Jones above, that by a team of seismologists 1 on the Witwatersrand of 10 x 1010 ft.lbs., that by Coates of 3.8 x 10" ft.lbs., also referred to in the paper, that by Blan-chard2 for the catastrophic rockburst at Springhill, N.S., of only 7.4 X 107 ft. lbs., and finally the range covered by Cook, referred to in the paper. It is probable also that data for the heavy rockburst at Merkers3 in the WERRA potash area of Germany are available as it was recorded on seismographs from Moscow to Spain. It is the writer's impression that some standardization is present in the estimates above for 10 x 10 10, 3.8 x 1010 and 7.4 x 107 ft.lbs., respectively. The latter, for Springhill, represents a relatively low order of magnitude. It is obvious that any energy estimate must be related to the local geometry of openings at the time of the event. It is also obvious that any explanation of the causes of rockburst must be capable of providing a wide range of energy. However, we must remember that the energy release is an effect indicating magnitude. The cause lies with the mechanism initiating the primary failure, generating the seismic activity, to which much of the damage is probably due.

Jan 1, 1967

By John Birkinbine

The experience of the past five years has furnished opportunities to study and to partially explain the operation and some of the causes of the short blast of Warwick Furnace at Pottstown, Pennsylvania, as described in the paper read at the Lake Superior Meeting, in August, 1880.* The many inquiries concerning the details of furnace operation which followed the publication of the paper, and the expressed desire of furnace managers to be informed as to future operations of this plant, have encouraged the preparation of the following data. To make the record continuous, and add to the value of both contributions, the present paper commences where the review of a short blast of Warwick Furnace ended, and includes the data of another short blast of two months, and a subsequent continuous campaign of nearly five years, which, by comparison, we shall designate as "the long blast." Frequent visits to the plant in the five years, during which its operation could be studied, and correspondence with the manager, Mr. Edgar S. Cook, have given a knowledge as to general features and details, and the courtesy of the officers of the Company which has given free access to the books of record permits the presentation of data which it is believed will be welcomed by furnace managers. Interest will undoubtedly be increased by the remarkable results which Mr. Cook has achieved chiefly with anthracite coal in a furnace whose details of construction will scarcely be generally admitted as embodying advanced ideas, its height being but 55 feet, with a bosh diameter of 15 feet 6 inches, its bosh-slope comparatively flat, its crucible smaller than the average, and the heat of the blast never reaching 1000' Fahrenheit. At present writing the credit of the best anthracite blast-furnace practice recorded in our Transactions is conceded to be that pursued by Mr. Fackenthal, at the Durham furnace, and Mr. Cook, at War-

Jan 1, 1886

By A. J. Shaler, H. Udin, J. Wulff

In the study of the sintering of meta powders, we have come to the conclusion in this laboratory that further progress requires a more basic understanding of the operating mechanisms. This is emphasized in detail by Shaler. He has shown that a knowledge of the exact value of the surface tension is imperative for a solution of the kinetics of sintering. This force plays a principal role in causing the density of compacts to increase.2 Furthermore, a knowledge of the surface tension of solids is also applicable to other aspects of physical metallurgy. C. S. Smith3 points out the relation between surface and interfacial tension and their function in determining the microstructure and resulting properties of polycrystal-line and polyphase alloys. This paper describes one group of results of an experimental program designed for the study of the surface tension in solid metals. As a by-product of this work, considerable information has been obtained on the rate and nature of the flow of a metal at temperatures approaching the melting point and under extremely low stresses, a field of mechanical behavior heretofore scarcely touched by metallurgists. The importance of this additional information to students of powder metallurgy need not be stressed. Theoretical Considerations Interfacial tension arises from the condition that an excess of energy exists at the interface between two phases. Gibbs proves that this energy is a partial function of the interfacial area; thus: ?F/?s = ? where ?F/?s is the rate of change of free energy of the system with changing surface area, at constant temperature, pressure and composition, and ? is the interfacial tension, or interfacial free energy per unit area. If one of the phases is the pure liquid or solid, and the other the vapor of the substance, ? may properly be termed "surface tension," and is a characteristic of the solid or liquid. The attempt of a body to lower its free energy by decreasing its surface gives rise to a force in the surface which is numerically equal in terms of unit length to the free energy per unit area of the surface. Thus ? may be expressed either in erg-cm-² or in dyne-cm-1. Similarly, surface tension may be determined either by a thermo-dynamic measurement of the surface energy or by a mechanical measurement of the surface force. We have chosen the latter approach. Tammann and Boehme4 determined the surface tension of gold by measuring the amount of shrinkage or extension of thin weighted foil at various temperatures and interpolating to zero strain. The method is of questionable accuracy because of the tendency of foil to form minute tears when heated under tension. Their assumption of F = 2W?, where W is the width of the foil, is unsound, as the foil can decrease its surface area by transverse as well as by longitudinal shrinkage. Although their experimentation was meticulous, the paper does not include details of the sample configuration required for recalculating ? on a correct basis, even if such a calculation were possible. In the experimental procedure chosen here, a series of small weights of increasing magnitude are suspended from a series of line copper wires of uniform cross-section. This array is brought to a temperature at which creep is appreciable under extremely small stress. If the weight overbalances the contracting force of surface tension, the wire stretches; otherwise, it shrinks. The magnitude of the strain is determined by the amount of unbalance, so a plot of strain vs. load should cross the zero strain axis at w = F?. If balance is visualized as a thermodynamic equilibrium, the critical load is readily calculated. At constant temperature, an infinitesimal change in surface energy should be equal to the work done on or by the weight: ds = wdl [A] For a cylinder, s = 2pr2 + 2prl [2] If the volume remains constant, r = vV/pl [31 s = 2vpl+2V/l [4] ds = vpv/l - 2V/l²) dl [5] Substituting [5] into [I] gives for the equilibrium load, w = ?(z/rV- 2V/12) [6] and, again expressing V in terms of r and l, w = pr?(1 - 2r/l [7] Here the end-effect term, 2r/l, is neglected for thin wires in subsequent work. Eq 7 can be confirmed by means of a stress analysis. If the x-axis is chosen along the wire, then the stress is 2pr? - w pr² pr2 [8] A cylinder of diameter dis equivalent to a sphere of radius r, insofar as radial surface tension effects are concerned.³ Thus xv = 2?/d = ?/r = sz [9] For the case of zero strain in the x direction, the strain will also be zero in the y and z directions. Since the wire is under hydrostatic stress, Eq 8 and 9 are

Jan 1, 1950

By J. V. Emmons

THE processes of hardening and tempering steel tools within the past 15 or 20 years have been so developed that the forward strides of the industry can scarcely be followed by the average observer. No small part of the credit for this phenomenal advancement is due to the improved methods of measuring the high temperatures necessary. Pyrometry has made possible the discovery and use of the many special alloy steels the wonderful properties of which are revolutionizing the industrial world. So sensitive are these steels to changes of temperature that often a variation of only 10° F. at a critical point of the heat treatment will cause the failure of the tool. In the tool-manufacturing industry today, accurate control of the many heating operations is imperative. The principal processes in the manufacture of tools that require accurate high-temperature measurements are annealing, carburizing, hardening, tempering, and laboratory research. Several other operations, such as forging and straightening, use rougher and correspondingly less accurate methods. These operations are usually performed in the following approximate ranges of temperature: DEGREES F. DEGREES F. Annealing 1000 to 1700 Tempering 200 to 1200 Carburizing 1400 to 1000 Forging 1400 to 1800 Hardening 1400 to 2500 Straightening 300 to 1300 Laboratory research covers the entire range. Annealing and carburizing are usually done in muffle or semi-muffle furnaces, heated with coal, coke, oil, gas, or electricity. Many of them are of large size, holding several tons of steel at one charge. Both indicating and recording pyrometers are used. The recording instruments are generally of the thermoelectric type, while for the indicating, both optical and thermoelectric are used.

Jan 9, 1919

By H. E. Nold

ThE raw materials of the ceramic industry are mostly clays. This raw material is ground, water is added and the mixture pugged into a moist, plastic, rather stiff mass. From this mass the desired units of manufacture are made (bricks, hollow building tile, sewer pipe, etc.). These units are dried; then placed in kilns and heated until the desired degree of vitrification is obtained. For firing ceramic ware, two distinct types of kilns are used; namely, periodic and continuous tunnel. Periodic Kilns Periodic kilns are those ordinarily seen in a brick plant. They are either round or rectangular. The raw, dried, formed ware is piled or set in the kilns to depths frequently exceeding 10 ft. The kiln is heated until the ware is matured, then gradually cooled sufficiently to allow men to remove the ware; then the cycle is repeated. The time duration of the cycle may be more than two weeks. In order that heat can be distributed uniformly throughout the pile or setting, the units are placed so as to leave open spaces or flues throughout the pile for the passage of the hot gases. Each kiln is provided with a number of fireboxes (usually 10 or 12) spaced equally in the outside wall. The fireboxes may be equipped with flat or inclined grate bars or they may have no grates at all (dead bottom). Down-draft kilns are most used. In these the hot gaseous products of combustion from the fireboxes are deflected upward by bag walls just inside the fire zone. From the top of the kiln the gases are drawn down through the setting, off through holes in the kiln bottom, and conducted to a stack or stacks. In up-draft kilns the fireboxes are usually set somewhat lower. The hot gases are drawn inward and upward through the ware and pass off from the top. Up-draft kilns find their greatest use in the firing of common brick. In either case the problem is to maintain, as nearly as possible,

Jan 1, 1934

Discussion of the paper of W. C. PHALEN, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 93, September, 1914, pp. 2249 to 2265. DAVID T. DAY, Washington, D. C.-Consider the United States broadly and the distribution of the salt industry. Think of the old solar-evaporation process up in New York State, then of the more recent processes in Michigan and Kansas and Louisiana, where the rock salt furnishes a large industry, then of the solar-evaporation process at Salt Lake, then turn to the crucial place in the United States, where there is an embarrassment of salt, and that is California. I am not forgetting' the immense body of salt east of that in the Virgin River country of Utah; but in California the situation is interesting. There are very large quantities of salt in the Searles Marsh region; again, in Southern California, at the southern end of Death Valley, there are two or three mountains of salt which have been explored recently, where the salt is sufficiently pure to be used at once. There is also a large deposit of gypsum, and it would be possible there, by extremely cheap means, to produce an amount of salt sufficient to furnish the United States' greatest needs. The principal reason that capital has been deterred from developing such a large mass is not the fact that solar evaporation produces a great deal of salt around San Francisco, but the fact that if potash salt is to be produced in connection with the salt in the borax region a, great deal of ordinary salt must be disposed of. It cannot be dumped, for it would get back into the brine again; the first rains would bring that salt back into solution again. It must be sold, given away, or hauled to a distance, which would mean a considerable freight charge. The salt will be going begging. E. G. SPILSBURY, New York, N. Y.-The remark of Dr. Day's regarding the likelihood of the production of a large amount of waste salt brings to my mind the condition that obtains in Germany in all of the potash fields. In Germany salt is a government monopoly. In the development of the potash deposits, it becomes a grave question as to how much salt they may be allowed to extract and bring to the surface.

Jan 4, 1915

By H. E. Nold

THE raw materials of the ceramic industry are mostly clays. This raw material is ground, water is added and the mixture pugged into a moist, plastic, rather stiff mass. From this mass the desired units of manufacture are made (bricks, hollow building tile, sewer pipe, etc.). These units are dried; then placed in kilns and heated until the desired degree of vitrification is obtained.1 For firing ceramic ware, two distinct types of kilns are used; namely, periodic and continuous tunnel. PERIODIC KILNS Periodic kilns are those ordinarily seen in a brick plant. They are either round or rectangular. The raw, dried, formed ware is piled or set in the kilns to depths frequently exceeding 10 ft. The kiln is heated until the ware is matured, then gradually cooled sufficiently to allow men to remove the ware; then the cycle is repeated. The time duration of the cycle may be more than two weeks. In order that heat can be distributed uniformly throughout the pile or setting, the units are placed so as to leave open spaces or flues through-out the pile for the passage of the hot gases. Each kiln is provided with a number of fireboxes (usually 10 or 12) spaced equally in the outside wall. The fireboxes may be equipped with flat or inclined grate bars or they may have no grates at all (dead bottom). Down-draft kilns are most used. In these the hot gaseous products of combustion from the fireboxes are deflected upward by bag walls just inside the fire zone. From the top of the kiln the gases are drawn down through the setting, off through holes in the kiln bottom, and conducted to a stack or stacks. In up-draft kilns the fireboxes are usually set somewhat lower. The hot gases are drawn inward and upward through the ware and pass off from the top. Up-draft kilns find their greatest use in the firing of common brick. In either case the problem is to maintain, as nearly as possible,

Jan 1, 1933

By M. D. Banus, M. B. Bever, A. K. Jena

Measurements of the heat effects on addition of various solid phases of InSb to a solution calorimeter have confirmed the existence of a new high-pressure plzase InSbQII), which was jormed at 37 kbar and 623°K. The heats of formation of InSbQ), InSbfl), and InSb(111) have been measured and the heats of transjormation of InSb(1) to InSb(1l) and InSb(Iii) and of 'InSb(ll) to InSb(iiI) at atmospheric pressure and 78°K have been determined independently. Other thermodynamic properties of these phases, the phase boundary InSb(i)/InSb(ll), and the relative positions of the triple points are calculated. The pressure-Dolume term is shown to be more critical than the internal energy difference in making the phase InSbQ) less stable than InSb(II) at high pressures. Observations on partially transformed specimens suggest that the transformation of' metastable InSb (III) takes place in the two steps InSb(lll) — InSbQI) and InSbQI) — InSb(l). The compound InSb can exist as several phases depending on the temperature and pressure. The phase InSb(I), which is a semiconductor having the zinc-blende structure, transforms into the phase InSb(11) at a pressure of about 23 kbar and room temperature.'-3 The phase InSb(II) has the 6 tin structure,4-6 is metallic, and becomes a superconductor below 2.lok7 An orthorhombic phase of InSb has been reported to occur above a pressure of approximately 30 kbar at room temperature.' This phase is also a superconductor below about 3.4k9 The phase InSb(I1) is retained at atmospheric pressure if it is quenched to 78°K under pressure,6,7 but tends to transform at higher temperatures and does so explosively above approximately 210ok,7 A value of the heat of transformation of InSb(1) to InSb(II) at 210°K and atmospheric pressure has been reported.' A concurrent publication'0 reports evidence for a new solid phase InSb(III), which was formed by annealing InSb above 58 1°K at 37 kbar, above 560°K at 52 kbar, and above 473°K at 65 kbar. Specimens of InSb(II1) had a superconducting transition temperature of 4.lo ± 0.1oK. X-ray diffraction patterns also indicated the presence of a new phase. In this communication, thermodynamic properties of the phases InSb(I), InSb(II), and InSb(II1) are reported and discussed. The phase boundary InSb(I)/InSb(II) and the relative positions of the triple points are calculated. 1) EXPERIMENTAL 1.1) Preparation of Specimens. Specimens of the high-pressure phases of InSb were prepared in a belt-type high-pressure chamber by a tichnique described in detail elsewhere.'' Charges of 0.6 to 0.8 g of Cominco semiconductor grade InSb were used. The temperatures were measured with a chromel-alumel thermocouple, the hot junction of which was within 0.5 mm of the specimen. The specimens were heated under a pressure of 37 kbar for 1 hr at 723°K (which is well above the liquidus) and quenched to room temperature. One set was annealed at 523°K and another set at 623°K for 20 to 24 hr. These annealing temperatures were chosen because 523°K was below and 623°K was above the temperature of the transformation of InSb(II) to InSb(1Tl) at 37 kbar.10 The specimens were then cooled to 125°K by passing liquid nitrogen through the jacket of the belt die before the

Jan 1, 1968

By John H. Smith

Because of increased pressure from federal and state regulatory agencies, most acid flows will require some sort of treatment prior to being discharged to receiving streams. In many industries, the volumes of liquors are large and their acid content varied. Development of a waste treatment process minimizing equipment cost and utilizing land efficiently is mandatory. Methods of acid neutralization with lime have been known for years, however, the volume and characteristics of the resultant precipitated solids can create a disposal problem. Also, when standard lime treatment is used, the settling characteristic of the precipitated solids is normally slow. In some instances, the necessity of added dissolved solids removal, such as iron, needing aeration, add to the problem of concentrating neutralized solids.

Jan 12, 1972

By Robert A. Rapp

The standard molar free energy of formation of MOO,was determined between 750o to 1050o C in galvanic cell measurements involving the solid electrolyte Zr0.85 Ca0.15 O1.85. Use of the reference electrodes Fe + FexO and Ni + NiO Provided two independent determinations of FoMoo2. The data may be represented by the equation FMoO2 = -137,500 +40.0T(°K) which is in good agreement with previous CO/CO, gas equilibrium measurements of Gleiser and Chipman. The standard molar free energy of formation of molybdenum dioxide has recently been reported over a large range of high temperatures from the calorimetric experiments of King, Weller, and christensen.' Gleiser and chipman2 have also recently determined ?FmoO2 from 926o to 1068oC in CO/CO2 gas equilibrium measurements. Earlier gas equilibrium studies have been made and reviewed by Gokcen.' Over the temperature range studied by Gleiser and Chipman their values for ?FoMoO2 differed from the calorimetric data by about 700 cal. This investigation was undertaken to resolve this difference and thereby establish the two phase mixture of Mo + MOO, as an electrode of well-known oxygen potential for galvanic cell applications at very high temperatures. The galvanic cell technique involving the Zr,.,, Ca,0.15 01.85 solid electrolyte was introduced for the

Jan 1, 1963

Jan 1, 1957

By Charles R. Fettke

The permeability of an oil or gas sand is its capacity for transmitting fluids, either liquids or gases, under pressure. The permeability of a sand depends upon the size and shape of the openings in it and the extent to which these communicate with one another, as well as upon the ratio of their volume to the total volume of the sand. The apparatus employed and the method of procedure used by the authors in conducting the permeability tests have been described in a previous pub1ication.l For the tests described here 1/2-in. cubes were used. They were set in the lower end of a 1-in. union, inserted in a square hole cut in a hard rubber stopper which fitted into the lower end of the union. In the tests with air, volumes were measured with a wet American gas meter of 100 cu. ft. capacity. In those with water, distilled water at room temperature was employed, unless otherwise noted. DescRiption of Sands Tested The tests described in this paper were performed upon 18 samples representing typical oil and gas sands from 7 localities in northwestern Pennsylvania. For purposes of identification, the cores from which the samples came have been designated by capital letters, the sequence of the samples in the cores by numerals, and the individual cubes by small letters. All cubes from the same samples came from adjacent portions parallel to the bedding. Core A of the Bradford sand came from the north central part of the Bradford field, from an area where water-flooding operations have proved highly successful. Core B of the same sand was obtained from the southern part of the field. This core contained a so-called "loose streak," 7.5 ft. thick, in the middle portion of which B2 is a representative sample. The "loose streak" has given trouble in water-flooding but responded favorably to an air-drive, using a pressure of 300 lb. The natural production was increased approximately five times over a period of three years in which the air-drive was in operation. Core C, also of the Brad-

Jan 1, 1931

By Bjorn N. P. Paulsson

A number of granitic rock specimens have been studied from the Stripa mine site in connection with a large-scale geomechanics research program. The purpose of the program was to evaluate and develop field and laboratory techniques for rock mass characterization and to determine design parameters for storage of nuclear waste. In this paper a minicomputer-based technique for studying dynamic rock properties in the laboratory is described, together with results from the tests. The specimens were tested under different uniaxial and saturation conditions. Specimens from a field-heated rock mass were also tested to determine if temperatures typical of those encountered with nuclear waste would introduce additional fracturing. Both Vp and Vs increased with stress for both saturated and dry specimens. Both Vp and Vs were higher for saturated specimens at all stress levels compared with the dry. The velocities increased linearly or near linearly with saturation. The test results on the previously heated samples indicate that attenuation is more sensitive to thermally-induced microfracturing than velocities. Analysis of the attenuation values with stress show that rock heated to 200°C is damaged, and that the damage is in form of low-aspect ratio fractures.

Jan 1, 1984

By C. E. Jackson, E. C. Nelson, A. L. Christenson

Much information regarding the transfornlatio~lal characteristics of a steel as it cools in a known manner from the austenitic state can be obtained from dilatometric studies. This method has received more arid more attention because of its great flexibility, accuracy, and ease of interpretation. 'The method is entirely applicable to any rate of heating and cooling although the experumental procrdures for high rates of cooling have offered some difficulties. This paper presents a description of equipment employing cooling rates up to 500 °C. per secorld and the results of dilatometric observations on six commercial steels are included. French and Klopsch1 studied the cooling transformations of a serirs OF carbon steel, using the thermal arrest method. This was followed by the systematic investigatiol1 of Esser and co-workers on the effect of carhon2 and other alloying additions. in which the transforlnation temperature\ were determined by magnetic induction measurements indicated by a string galranoineter. Emphasis was placed on determining Ar' trailsformations and the critical cooling rates for these steels. The maglietic measurements wrere used in an effort to obtain more accurate data at higher cooling rates. Measurements of thermal arrest were made also to check the validity of the magnetic indications, and good correlation was found between the two, although Esser's,Ar' temperature measurements on iron-carbon alloys were about 200°F. lower than the measurements made by Fresnch and Klopsch. A notable contril~ution by Esser was the introduction gas quenching. wever and Rose4 used a moving-coil galranometcr in the study of the .Ar and Ar" of iron-carbon alloys by the thermal arrest method and obtained somewhat lover Ar" temperatures than those observed by Esser below I per cent carbon and considerably higher ahove. They concluded that the cooling rate had little influcncc on the Ar" temperatures above 0.4 per cent carbon, although Esser had observed a decrease in the -4r" temperature with increasing cooling rate with similar steels. Digges determined the .Ar" temperature4 for a scries of high-purity iron-carbon alloys, and close agreement with his results was obtained by Greninger. The thermal arrest method. together with metallographic observation used in both these studies, represents the latest investigations of this type. Any investigation by thermal analyses is dependent on the heat of reaction and the specific heat of the

Jan 1, 1945

By John V. Beall

When the mineral seekers came, they brought romance, excitement and, too often, transitory riches. It has been so for uncounted centuries. While the rich ore lasted, living was high and money flowed-mostly out of town. The whole creation was like a circus. The headframe went up like the center pole of the big top. The reduction works was an ingenious affair; an opportunity for self-expression by the mining engineer on the job. When the high grade gave out or the bottom dropped out of the market, the whole show folded. Machinery was scavenged for the next location. About all that was left were the raw footings, like giantsteps on the hillside; and the headframe above the silent diggings. Mostly, the people went away too. Arizona Territory was like that at the turn of the century. It can still happen. But, in copper, the age-old pattern has been disrupted. From Mineral Park in the northwest to Chino in the east and Cananea in the South, a growing number of companies have emerged-large, stable, productive. Southwest copper is truly a mighty industry, accounting for one fifth of world new copper production. In this period of scientific development, changes are fast, often dramatic. But even mining engineers, or possibly more so because they have an intimate knowledge of the industry, fail to appreciate the evolutionary changes that have shaped Southwest copper into what it is today.

Jan 10, 1965