Search Documents

By E. H. Timmerman, A. F. van Everdingen, J. J. McMahon

The prevent paper contains a method which combines the material balance equation' with the water influx equation' to obtain reliable values for the active oil originally in place and a quantitative evaluation of the cumulative water influx. The method is illustrated by an application to a reservoir without original gas cap. In the absence of an original gas cap. results may be obtained using only field production and pressure data, PVT analyses. and a minimum of subsurface information. CHARACTERISTICS OF RESERVOIR AND RESERVOIR FLUIDS Production in the field under review is obtained from the top of the Wilcox formation of Eocene age, at a depth of approximately 8,100 ft subsea. The structural map, Fig. 1, shows that the accumulation, half elliptical in shape with the long axis in east-west direction, is trapped to the north and on the upthrown side of a normal fault. A number of east-west faults with additional minor faulting in random directions are found in the general area, and seismic information and production performance indicate in this particular case the existence of a second fault a short distance downdip, with a strike more or less parallel to the fault controlling the accumulation. It is estimated that 1,830 acres were originally underlain by oil and that the maximum thickness of the original oil column, about 37 ft, was only slightly greater than the maximum thickness of the oil-bearing sand. Maximum net sand thickness was estimated at approximately 26 ft. From logging and subsurface information the gross sand volume has been placed at 37.400 acre-ft. which reduces to about 27,500 acre-ft after probable non-productive intervals have been deducted. The following table presents laboratory analyse; data for the Wilcox sand cores. Average Average Samples Considered Permeability Porosity All Samples 236 md ..19.9percent Samples with k>l md 256 md 20.5 per cent Samples with k>8 md 275 md 20.9 per cent Interstitial water was estimated at 15 per cent. The initial gas-oil ratio was approximately 900 cu ft/bbl. and the initial shrinkage factor was determined by the laboratory to

Jan 1, 1953

By C. E. Brukl, E. Rudy, St. Windisch

The ternary-alloy system Nb-Mo-C was investigated by means of X-ray, melting point, DTA, and metallo-graphic techniques; a complete phase diagram for temperatures above 1500°C was established. Above 1960°C, niobium monocarbide and the cubic (Bl) high-tenzperature phase in the Mo-C system form an uninterrupted series of solid solutions. The ternary range of the pseudocubic q MoCl-, is very restricted. Dimolyb-denum carbide dissolves up to 44 mol pct Nb2C (2240°C), whereas the maximum solid solubility of MO2C in Nb2C does not exceed 5 mol pct. The order-disorder transformation temperatures in Mo2C and Nb2C are lowered by the mutual metal exchanges. Six invariant (p = const) reactzons occur in the ternary system; three correspond to class 11-type four-phase reactions involving a liquid phase, one to a class I (eutectoid)-type, and two further isotherms are associated with limiting tie lines. The results of the Phase diagram investigation are discussed, and the thermodynamic interpretation identifies the low relative stability of the binary sub-carbides in conjunction with the large stability diflerences between niobium and molybdenum carbides as the cause for the formation of a stable equilibrium between the monocarbide and the metal phase in the ternary reson. Due to their refractoriness, the carbides of the high-melting transition metals have received increased interest in recent years as base materials in composite structures for aerospace applications at high temperatures and for the development of self-bonded cutting tool materials; other novel fields of application include power reactors, where operation at high temperatures becomes essential for attaining high power efficiencies. In these applications, the increased reaction rates at high temperatures require a close consideration of the chemical interactions between the alloy constituents. As a consequence, a detailed knowledge of the phase relationships in the alloy systems is required in order to provide a sound basis for developmental -type work. Partly as a result of the considerable experimental difficulties associated with the investigation of this high-melting alloy class, no complete studies of ternary metal-carbon systems have been performed until recently. Even the high-temperature phase relationships in the binary transition metal-carbon systems have been delineated only during the past few years to a degree of accuracy required for a more detailed study of ternary or higher-order alloys. In recent investigations of binary and ternary systems of refractory transition metals with carbon, boron, and silicon,&apos; alloys from the ternary systems Nb-Mo-C became of interest because of the demonstrated possibility2,3 of obtaining compatible composites based on metal + monocarbide combinations. In the meantime, however, studies in other, but related, ternary metal-carbon systems, such as Ta-W-C, have shown that the solid-state equilibria may change significantly toward higher temperatures (>2000°C), and that extrapolations based on low-temperature equilibrium data are, in general, not very reliable. Although the lower-temperature (<2000°C) phase relationships in the Nb-Mo-C system are similar to those found in Ta-W-C, a cursory thermodynamic analysis of the equilibria indicated4 that complete solid-solution formation between Mo2C and Nb2C should not occur at higher temperatures. The present work was conducted in order to experimentally verify these expectations and, in addition, to provide phase equilibrium data in the melting range of the alloys. In the boundary systems, niobium and molybdenum are known to form a continuous series of solid solutions.576 The continuous solubility was also confirmed by Kornilov and Polyakova,7,8 who also observed a minimum melting point at 22 at. pct Mo and 2345°C. The phase diagram investigations of the Nb-C system by Storms and Krikorian9 and Kimura and Sasaki10 were recently supplemented by Rudy et al.11,12 The system contains a high-melting monocarbide with the B1 structure, Table I, and a subcarbide, Nb2C, which exists in at least two different states of sublattice order at low temperatures47"-&apos;3 and a disordered state above approximately 2500°C.11,12 The melting-point measurements by Rudy et al .11,14 are in close confirmation of the data by Kimura and Sasaki.10 The rather complex phase relationships in the Mo-C system were only recently Clarified.15,18 The system is characterized by three congruently melting, intermediate phases, MozC, ? MoC1-x and a Mol-,, Table I, of which only Mo2C is stable at temperatures below 1650°C. Substoichiometric MozC exists in several states of sublattice order which interconvert in homogeneous phase transitions. Hyperstoichiometric compositions cannot exist in the ordered state. Upon cooling through a critical temperature range, the

Jan 1, 1968

By M. K. Barnett

[ ] ENGINEERING research consists, broadly speaking, in the investigation of the effect of the variations in a number of factors on some property of a product or characteristic of a process. The unambiguous description of the product or process requires that the property or characteristic be expressible in quantitative terms. For the purpose of practical control, it is likewise desirable that the independently variable factors governing the product or process be quantities, although this ideal goal is not always attained. Maximum efficiency-i.e., the attainment of the maximum amount of reliable, useful information relating to the influence of the factors on the property of the product or characteristic of the process, for the least expense-is an important requirement for the satisfactory operation of a research organization. Obviously, a necessary condition for the attainment of maximum efficiency is an adequate knowledge of the specialized field in which the experimental research lies. While necessary, this condition is not sufficient. Proper attention must also be given to the general principles of experimental design together with the modem methods for the analysis and evaluation of experimental data. The present discussion is confined to a single design, the so-called "factorial" design. This design is of special interest in that it attains its goal, maximum efficiency, by directly departing from the

Jan 1, 1947

By Merlon C. Flemings, Theodoulos Z. Kattamis

Examination was made of the distribution of tnanganese and nickel in colutrrnar dendrites of a cast low-alloy steel; more limited work was corzducted on chromium. Corresponding "segregrction ratios" were calculnted and shown to be relntivelv insensitive to cooling rate (&apos;&apos;segregation ratio" is defined (Is the ratio of maximum to minimum concentrations within a volume whose dimensions are the order of the dendrite-arm spacing). Isoconcentratiorl curves were determined by the electron micropvobe and by rt7etallografihic studies on specimens subjected to isothermal-transformation treatments. From construction of isoconcentration curves, morphology of columnar dendrites is descvibed as intermediate between Perfect rodlike and sheetlike morphologies. The study is extended to equiaxed dendrites and it is shown that the strcture of these dendrites is sittlilar in many respects to that of columnar dendrites. On the basis of tlze sheetlike morphology of dendrites, a simple model is pvoposed for calculation of honzogenization kinetics. Results of trzatllevlatical analysis brcsed on this utzodel are given. This analysis relates residual segregation to time at homogenization temperature; it is in agreement with experiment. Calculations are given which show that even for relatively rapidly cooled material (of 1-ine dendrite-artn spacing) treatmets at 1200°C or above are necessary to achieve slgxificant Izomogenization of elenlents other than carbon itz reasonable time (e.g., rnangclnese, nickel). Conlplete homogenization of carbon is obtnined at much lowev tenlperatures (below 870°C). IN dendritic solidification of castings and ingots, solute redistribution during freezing results in mi-crosegregation of most alloy elements. The micro-segregation is such that minimum solute concentrations occur at the center of dendrite arms and maximum concentrations occur between dendrite arms. Residual segregation after subsequent therma1 processing (homogenization) depends on maximum and minimum initial concentration, on the detailed geometry of the isoconcentration surfaces within interdendritic regions, on the diffusion coefficient of the solute, and on time of thermal processing. The objective of this work was to determine, for a low-alloy steel, maximum and minimum concentrations, and the geometry of isoconcentration surfaces, primarily in order to permit calculation of homogenization kinetics. Most of the work reported was conducted on Samples from a unidirectionally solidified, fully columnar ingot. This type of ingot is made by extracting heat during solidification from one face; techniques for accomplishing this have been discussed.&apos; Samples were taken at several locations, up to 5.75 in. from the mold chill face; the bulk of the work was performed on samples at 5.75 in. Alloy cast was, nominally, 0.4 pct C, 1.8 pct Ni, 0.8 pct Cr, 0.7 pct Mn, 0.25 pct Mo, 0.3 pct Si, and the balance iron. Brief study was also made on samples from an ingot which solidified with equiaxed grain structure. SAMPLE PREPARATION AND ANALYSIS Samples for electron-microprobe analysis were incorporated in mounts that included pieces of electrolytic nickel, chromium, and manganese, in order to normalize the intensities of these solutes in the specimens; also, a piece of electrolytic iron was included to measure the background. All specimens were polished in the usual metallographic manner. After the microprobe traces were made, the path was revealed by etching the specimens with picral. All microprobe analyses were made by point counting, integrating for 30 sec. The distance between points was fixed from 2 to 10 p, according to the precision desired in each case, the fineness of the structure, and the concentration gradient existing in a given area. (The distance was chosen 2 to 5 p near the maximum-concentration regions and 5 to 10 p near the minimum concentration.) The "take-off" angle for the A.R.L.-Model No. 21000 microprobe employed was 52.5 deg. Samples for metallographic analysis of isoconcentration curves were prepared by austenitizing at 1540°F for 20 min, quenching to the nose of the TTT curves (1200°F), heat treating isothermally at this temperature for a given time 0, and then quenching to room temperature. Due to concentration gradients existing in a dendritic structure, no transformation will take place for a given time 0 of isothermal heat treatment in the regions where the a.lloy concentration is higher than a given limit. Thus, the dendrite appears limited by an isoconcentration curve and can be made to appear to grow by varying the time of isothermal heat treatment.

Jan 1, 1965

By H. David Swain

On Bougainville Island in Papua New Guinea, Bougainville Copper Ltd. (BCL) has successfully applied electronic data processing (EDP) techniques to pit operations and mine planning. Though the EDP program is not complete, BCL has realized significant improvements in short and long range mine planning, and equipment and manpower utilization. About 80% of BCL&apos;s 4000 employees are Papua New Guinea nationals, and most have little education or training. The operational characteristics of the computer equipment, however, have been quickly adapted by users with low educational standards.

Jan 3, 1979

Jan 1, 1970

Jan 1, 1963

By John Howe Hall

The recently announced run of three years, nine months and eleven days made by a crucible steel melting furnace of the Columbia Tool Steel Co., which is claimed as a world&apos;s record, brings forcibly to our attention the great improvements that have been made in the design, construction and operation of the Siemens regenerative crucible melting furnace since its introduction in this country. Credit for this advance should be given to the furnace designer, the manufacturer of refractories, and the operators, of the furnaces, whose persistent efforts and intelligent co-operation in attacking the problem have resulted so satisfactorily. There are three factors that determine the life of a crucible furnace, or any other furnace for that matter: Design, nature of refractories, and conditions of operation (including the nature of steel melted); and to some extent these factors are interdependent. Thus, for instance, if a crucible furnace is to be operated single turn and allowed to cool off considerably at night, in order to save fuel, the use of clay-brick melting holes may be advisable, since silica brick is not well adapted to endure repeated heating and cooling. But the total life of a clay-brick melting hole is necessarily short. Again, if local conditions such as danger of flood make necessary the building of the furnace largely above ground, so that the radiation of heat is promoted, the cooling down of the furnace over the week ends, when no steel is melted, will be considerable—and the contraction of the furnace that results tends to wrack it to pieces. The character of the metal being melted affects the life of the furnace to a great extent. Low-carbon steels and steels made from iron and charcoal require higher temperatures and much longer melting time than high-carbon steel or steel made largely from scrap; the life of the furnace will be shorter, and the number of heats melted will be much less, when such materials are melted. The figures available, showing the life of furnaces, are for this reason especially not strictly comparative, since the variations in the steel melted undoubtedly affect the life to a greater or less extent. Probably, however, the method of handling is as important a factor

Jan 1, 1914

By Hal M. Scrugham

UNITED States Steel Co.&apos;s Tennessee Coal & Iron Div. Wenonah mines present definite materials handling problems arising from the natural features of the operation. Trackless equipment went a long way toward supplying the answers-but at the same time gave birth to several new posers. Machines-trackless or otherwise-require maintenance and Wenonah&apos;s experience may do much to add to the body of information already available on this type of equipment. Let&apos;s look at the mines themselves. Ore is of sedimentary origin, extending over an area of several square miles. A thickness from 8 to 14 ft is mined. Bed dip varies from the horizontal to 20 pct in local rolls. Practice is to mine across the dip at 14 pct or less. A parting forms a smooth footwall in some of the mines while in others the footwall must be blasted smooth. Ore weighs 215 lb per cu ft in place and is extremely abrasive.

Jan 6, 1953

By Fredrick C. Kruger

Introduction This surprisingly little-known group of minerals, the nonmetallics, so-called for their lack of metallic luster, is the largest group of the mineral kingdom, and cinstitutes perhaps 75 percent of all mineral species. For the most part, these minerals are compounds of the common acids, oxides, hydroxides, and two elements, carbon and sulfur. The list of the non- metallic minerals, therefore, is very long. It includes the borates, carbonates, chlorides, fluorides, nitrates, phosphates, silicates, sulfates, and less commonly, arsenates, chromates, molybdates, suliides, tungstates, and vanadates, the latter groups, and many of the oxides, being sought principally for their metal content. Those nonmetallics used commercially are generally called the industrial minerals, although in addition this term also includes a considerable group of rocks. The list of industrial minerals and rocks is continually growing as new uses are found, and it now numbers over 300 commodities. The industrial minerals industry has developed since about 1920. There- fore, the development has been fast, and it has been more or less parallel with the development of the art of minerals beneficiation. General Discussion of the Group This group is so heterogeneous that it has defied logical, or widely accepted, classification, whether by origin, composition, or end use, and perhaps for this reason the industrial minerals generally have received short shrift in both teaching and research. Except for those involved with asbestos, cement, fertilizers, gypsum, salt, sand and gravel, few large companies have deigned to enter the field, and consequently most industrial minerals have been developed for the most part by the small operators or entrepreneurs. Yet surprisingly, except for one war year, the nonmetallics have always surpassed the metals in value and tonnage (Fig. 1). One main characteristic that most of the nonmetallics have in common is direct sensitivity to labor and transportation. In other words they are characterized by large bulk and low-unit value, and hence have what might be termed a "place value".

Jan 1, 1971

By H. R. Thresh, A. F. Crawley

THIS paper reports the results of viscosity measurements on cadmium and indium undertaken as part of a continuing program of liquid metals research at the Mines Branch, Department of Energy, Mines and Resources, Ottawa, Canada. For several years this work has continued with support from the Canadian Zinc and Lead Research Committee and the International Lead and Zinc Research Organization. In the literature, existing viscosity data for cadmium are conflicting and for indium are scarce. To achieve reliable viscosity values, further work was deemed desirable. Viscosities were measured using an absolute technique applied to an oscillating closed right cylinder of liquid metal. The apparatus, constructed in this laboratory, and the techniques involved in its use have been described in an earlier paper.&apos; In calculating viscosity coefficients from the experimental data. Roscoe&apos;s2 mathematical analysis was used. Because accurate viscosity determinations are dependent on accurate density data, and since the available data in the literature are conflicting, the densities of liquid cadmium and indium were also determined in this laboratory by a pycnometric technique. This increased the control exercised over all the variables contributing to the accuracy of viscosity measurements. For both density and viscosity determinations, cadmium and indium of 99.999 pct purity were used. These materials were obtained from Cominco Ltd. In order to suppress excessive evaporation losses and help prevent oxidation, a technique developed in measuring the viscosity of zinc&apos; was used for cadmium. This involved maintaining an atmosphere of purified hydrogen in the viscosimeter during the rela- tively long periods while the experimental temperature was changed and stabilized between individual determinations of the logarithmic decrement. Then, immediately prior to a decrement measurement. the viscosimeter was rapidly evacuated to a pressure of about 2 X 10-6 torr. On the other hand. with indium. no difficulties arise from vaporization or oxidation. In this case. therefore. the apparatus was held under a constant vacuum of about 2 x 10-6 torr. When all sources of random and systematic error have been evaluated, the technique is considered to yield data accurate within 10.5 pct. The viscosity of cadmium was measured to a maximum temperature of 451.8°C and that of indium to 346.5°C. These temperatures are. respectively. 130° and 190°C above the melting points. Two separate runs were made on indium. The results are given in Table I and, when plotted. yield the smooth curves evident in Figs. 1 and 2. Values of A and C to fit the well-known Andrade1 equation were determined by a regression analysis. The equation is: where n = coefficient of viscosity. i = specific volume. T = temperature in °K Despite its empirical nature. Andrade&apos;s equation has been shown by many workers to describe accurately the temperature dependence of viscosity. During the current research program, this equation has been found to fit the data precisely for all the metals and alloys that have been studied.5,6 The A and C&apos; values for cadmium and indium are given in Table 11. Comparing the magnitude of the present data with those of previous workers,7-10 as has been done in Fig. 1, it is evident that the results of Fisher and Phillips10 deviate markedly from the rest. With the exception of one point from Gering and Sauerwald,7 all other data agree within ±2.5 pct. However, the agreement between the present results and the work of Menz and sauerwald9 is especially good over the entire experimental temperature range. Such agreement may be expected since Menz and Sauerwald&apos;s

Jan 1, 1970

G. W. TRAER (author&apos;s reply to discussion*).-Prof. Parr&apos;s discussion develops two points, upon which it seems desirable to comment. First, as to putting through a large enough tonnage to secure economic operation. At each manipulation of each oven 1500 1b. (680 kg.) of coal will be charged and the resultant coke discharged from a like amount of coal. . Sixteen slabs will be discharged at each manipulation, each approximately 5 ½ in. by 11 in. by 6 ft. (14 cm. by 28 cm. by 1.8 m.). The operating schedule of a commercial plant, based upon our observations and calculations, indicates a "through put" of at least 12 tons of coal per day for each oven. We have made these figures conservatively and feel confident of materially exceeding them in a fully developed operating system. Our oven plant, with containers, will not cost as much as high-temperature plants of the same capacity. They do not require container equipment; but this is much more than offset by the cost of the great basal heat regenerative flues. Our operating requirements are quite susceptible to the application of mechanical devices and we believe our labor cost will be well within the necessary limit. Second, as to Fig. 1 in my paper, showing the specific gravity&apos; of the tar. It Was not intended to show that the specific- gravity of -the tar rises With decreasing heat, since of course the contrary is the fact. One of the curves shows the relation between temperature and specific gravity and the other the relation between temperature and- yield. Our consulting engineer prepared the chart according to his customary method for showing two dimensions.

Jan 1, 1919

By C. Gatlin, N. E. Garner, A. Podio

Experimental data from single chisel blows on Leuders limestone are presented. A pressure chamber, similar in design to well known microbit drilling chambers, was utilized to impose variorcs stress states on the sample. Confining pressure of zero to 10,000 psi and borehole pressures from zero to 5,000 psi have been used in the studies. Pore pressure was zero and the rock samples dry in all instances. Force-displacement records and visual examination of the craters indicate that the mode of failure depends on both confining and borehole pressure in certain ranges, ranging from brittle, through a transition, to near plastic. The mode of failure is reflected in the observed blow force and energy data, as well as the shape of force-penetration curves. INTRODUCTION A previous paper&apos; presented initial data from the project on which this paper is the second report. While the first paper dealt with impact studies on synthetic rocks, the literature cited there is also pertinent to this paper, but will not be listed again in order to avoid needless repetition. This paper presents experimental data from single chisel impacts on limestone at certain simulated wellbore stress states. Specific variables investigated were combinations of borehole and confining pressure, crater geometry, a narrow range of impact velocity and the forces required to drive the chisel into the specimens under the varying conditions. EXPERIMENTAL PROCEDURE The same basic apparatus described in our earlier paper, except for the pressure vessel, was used in this study. Fig. 1 shows the complete experimental system. Fig. 2 shows details of the pressure cell, which is quite similar to the well known microbit drilling chamber. The confining (overburden) pressure system provides independent pressure control over the sample except for two, 21/4 in. diameter areas located on the sample ends. These two areas provide a pore pressure entrance on the bottom and a striking surface on the top where borehole pressure can be controlled. The ends are isolated from the confining pressure by O-ring seals. The borehole and pore pressures are related through the striking surface; they will be the same unless a seal is deposited on the borehole surface, either a mud cake or some other impermeable membrane. In these studies pore pressure control was not used, as the rocks were dry and unsaturated in all cases. Rock samples were prepared from 4-in. cubes as illustrated by Fig. 3. The circular disks of adhesive vinyl plastic protected the impact surface from the resin coating (Scotchcast No. 2) and were removed just prior to each test. This procedure insured a fresh uncontaminated surface for the impact. Fig. 4 shows the dimensions and loading of the sample, including the concentrations around the "borehole" periphery (O-ring seal). The rock used in this study was Leuders limestone, of Permian age (Leonard), quarried near Leuders, Tex. Geologically, Leuders limestone is a light gray, fossili-ferous limestone (oolitic foraminifera1 biosporite). Its fossil content is 80 to 90 per cent and consists primarily of calcitornellid, ostracods, pelecypods and oolites with the remaining part intraclasts. There are hematite or limo-nite rims on some of the intraclasts. The porosity is approximately 20 per cent, but the permeability is less than 1 md. There is no apparent orientation in the structure. Triaxial tests have been conducted to determine the variation of the physical properties of Leuders limestone in three orthogonal directions&apos;, and it is known to be unusually isotropic and uniform. Physical parameters for this rock are: uniaxial compressive strength = 9,700 psi; F = 32 and C = 2,700 psi; where + and C are Coulomb equation values (t = C+u tan +). Impact tests were run under the combinations of confining and borehole pressures shown in Table 1. Samples were dry with atmospheric pore pressure in all cases. Tests, in which elevated borehole pressures were applied, used a single layer of household Saran-Wrap to prevent horehole fluid invasion into the sample. This proved to be simple and reliable. The blunt wedge used in all the tests was 0.75 in. long and had an included angle of 60" with a 0.05-in. flat. In addition, a sharp 60" wedge was used for all confining pressures at zero borehole pressure. The chipper speed

Large equipment for quarrying and for the various stages of crushing and grinding are the trend for new and existing operations. Included are large size haulage units, fast drilling equipment, impact crushers and large mills capable of high tonnage rates for metallic and nonmetallic minerals. In grinding, large-size mills continue as the choice in industries where grinding constitutes a major portion of the processing. Typical is a 10 x 34 ft two-compartment mill in closed circuit with an 18-ft diam air separator for cement. Other cement mill sizes are in the order of 12 x 36 ft, 2500 hp; 10 x 37 ft ball and rod (wet), 1400 hp; 13 x 36 ft, 3000 hp; 13 x 40 ft (wet), 3000 hp. Several installations of combination ball and rod mills have been made, and one of the largest is 12 x 45 ft. In connection with the wet grinding of raw materials, the DSM 270-degree screen has been installed in several cement plants with the intention of producing a material finer than 50 mesh. In ore processing, large autogenous mills (121/2 x 20 ft) are being installed.

Jan 2, 1964

By John Birkinbine

Much has been contributed to the Transactions of the Institute concerning the construction and operation of American blast-furnares ; but the following compilation is offered as possibly furnishing additional information upon the general features, dimensions, locations, capacities, etc., of the blast-furnaces of the United States; while, incidentally, the ores upon which they rely are noted in a general way. The paper is presented chiefly as a compilation, and the figures given are selections from most reliable sources, or averages calculated from official statistics, placed for convenient reference, with a view of assisting those who consult the Transactions in determining the present relative merits and importance of various sections of the country. The scope of the paper has been restricted to as few topics as possible, and all the details of special plants, or notable outputs have been ignored. While every effort has been made to give correct figures and data, the changes which are constantly taking place in the iron-producing industry, will, undoubtedly, by the time the paper is in print, develop some errors. It is difficult to determine which of the blast-furnace plants of the country should or should not be considered as upon the active list. A number which have not been in operation for years are still reported as active, some of which will scarcely be put in blast again, and others are handicapped so that they can only operate in times of abnormal profits. It is therefore scarcely probable that there are over 600 blast-furnaces in the United States which can properly be considered as active; but so many considerations affect the various plants, that, it being impossible to determine the exact number, I have relied upon the annual reports presented to the American Iron and Steel Association. Concerning the number of plants which could be stricken from the list, the Secretary of this Association says: "In January last (1885) we enumerated 669 furnaces, which included many stacks which had not been in blast for a very long time, and others which could not be operated except during short periods of exceedingly high prices for pig iron. We have gone over this list very carefully and have eliminated 10 anthracite, 19 bituminous, vol. xiv.—36

Jan 1, 1886

By G. A. Croes, N. Schwarz

This paper reports the results of a series of model displacement experiments carried out for measuring the efficiency of the water-drive process. This series forms a continuation and extension of that described by Engel-herts and Klinkenberg. Detailed information has been obtained on the influence of the oil/water viscosity ratio. The results are represented in the form of a diagram from which both the oil recovery and the water/oil ratio can be easily read off as a function of the total production (oil plus water) for all values of the viscosity ratio M between I and 500. These resu1ts are viewed in the light of the two existing theories on water flooding, viz. that of Buckley and Leverett and that of Dietz. It is shown that if the Buckley-Leverett theory applies, the relation between the relative permeability ratio and saturation, which plays a major role in this theory, (.an be calculated with a high degree of accuracy from the results of the model experiments. Dietz&apos;s theory is found to be in agreement with the experimental results in a certain range of circumstances. A discussion of the physical background of the Buckley- Leverett and Dietz theories makes it clear why the latter fails to agree with some of the experimental results. INTRODUCTION For an economical exploitation of oil fields both a rational control of natural (primary) recovery processes and a proper application of artificial (secondary) recovery methods are essential. These require detailed information upon the dependence of the relevant flow processes on the variables by which they are governed. Three methods are available for obtaining this information: (1) (statistical) analysis of actual field data; (2) appropriately scaled model experiments; and (3) mathematical analysis of the physical problem. If sufficient data were available, the first method would, in principle, be the most reliable one, although it has the drawback that the basic relationships between the variables involved are to a large extent obscured by the natural inhomogeneities of most reservoirs. The most profitable procedure seems to be: (a) determining the fundamental relations for idealized reservoirs by methods (2) and (3); (b) checking the consistency of the results obtained by these two methods; and (c) establishing the range of applicability of these methods to actual reservoirs by comparison with the data accumulated under (1). In this paper items (a) and (b) are dealt with for the case of homogeneous loose sands initially saturated

Jan 1, 1956

By D. J. DeLazaro, W. Rostoker, R. E. Riley, M. Hansen

KNOWLEDGE of the isothermal transformation behavior and the TTT chart method of graphically summarizing such information has been of invaluable aid to the ferrous metallurgist in understanding and developing heat treatments intended to provide specific mechanical properties. It is to be expected that similar lines of study directed to titanium-base alloys will be as profitable. This paper summarizes, on conventional TTT charts, the isothermal transformation products and pertinent reaction rate data for binary alloys of titanium containing 1, 3, 5, 7, 9, and 11 pct Mo, respectively. The results so presented were derived from metal-lographic examination. Some X-ray diffraction work was done to clarify certain points of question. Ti-Mo System To the authors&apos; k.nowledge, TTT charts have only been used to describe the reaction rates of eutectoidal decompositions. It would seem that the kinetics of decomposition of any unstable solid solution might be conveniently described in this manner. The equilibrium diagram of the Ti-Mo system&apos; is shown in Fig. 1. The similarity with the Fe-Ni system will be recognized. Additions of molybdenum serve to stabilize the /3 phase to increasingly lower temperatures. The solubility of molybdenum in the a phase is restricted to less than 1 pct at 600°C. Under normal conditions. a homogeneous ,8 structure quenched to a, temperature in the a f & field will reject a of invariant composition. The rate at which this occurs depends on the degree of undercooling and the degree of supersaturation of /3. The structural character of the rejected phase may also be expected to be related to the undercooling. Materials and Experimental Methods A sponge titanium was used which has a nominal impurity content as reported in Table I. The nominal composition of the molybdenum used is also included. The alloys were prepared in 150 g melts by arc melting in an evacuated water-cooled copper crucible of the type reported in an earlier paper.&apos; The pancake-type ingots were forged to 1/4x1/4 in. bars and homogenized for 24 hr at 1000°C in evacuated Vycor bulbs. Specimens Vi in. thick were cut from these bars for heat treatment. The heat treatment cycles followed an invariant procedure. The specimens were soaked at 1000°C for 20 min under a helium protective atmosphere prior to quenching into a lead bath held at a temperature corresponding to a chosen degree of undercooling. After a prescribed period of time at this temperature, the specimen was removed and water quenched. A series of specimens so treated for progressively longer periods served to establish the times for initiation and completion of the decomposition of the /3 phase at a particular temperature. Although heat treatment of unprotected specimens in a lead bath does permit surface contamination by lead diffusion, this method is necessary to insure sufficiently rapid quenching rates. As long as the bath treatments were of less than 1 hr duration. the contaminated surface was not unduly deep and could be removed without excessive grinding. Metal-lographically, the contaminated zone could be readily distinguished from the pure binary alloy. Transformation Characteristics of Ti-Mo Alloys Metallographic examination showed that a supersaturated p phase may decompose by one of two processes. Alloys containing 1 to 9 pct Mo, when quenched in water from the homogeneous /3 field,

Jan 1, 1953

By D. R. Pratt, R. W. Hanks

The method of Caldwell and Babbitt for detennining Bingham plastic rheological constants from engineering pipe flow data has been erroneously used in many previous applications. A reanalysis of extensive pipe flow data from the literature is performed. Critical Reynolds numbers corresponding to the laminar-turbulent transition calculated from these data are found to agree with theoretically calculated values for the entire flow range studied. Similar agreement is found for the authors&apos; own data&apos; for flow of 10 slurries between parallel plates. The Bingham plastic model is shown to be a reliable representation of the flow of non-Newtonian slurries provided it is properly applied. If the Hedstrom number He = pD2 t0/?2 > 104, then the linear approximation method of Caldwell and Babbitt is invalid for pipe flow data obtained in systems of ordinary engineering interest, and the complete nonlinear form of the pipe flow Bingham plastic equation must be used in determining rheological parameters. INTRODUCTION Many materials of engineering interest must be handled and transported as slurries or suspensions of insoluble particulate matter in a Newtonian liquid. These suspensions frequently exhibit non-Newtonian rheological behavior which is reasonably well described by the simple Bingham plastic rheological equation1 Using this particular equation to describe the laminar flow characteristics of slurries was discussed at length by Caldwell and Babbitt2-4 who considered the flow of various clay slurries and sewage sludges. The model has since been used by many others.5-7 More recently the problem of predicting the laminar turbulent transition Reynolds number for Bingham plastic fluids has been treated8 for the case of flow in pipes. This paper points out errors which have existed in the analysis of Bingham plastic flow since the work of Caldwell and Babbitt2-4 and presents a reanalysis of the laminar turbulent transition calculatiod for Bingham plastic flow in pipes. In addition, new data obtained for flow of Bingham plastic slurries between parallel plates, both in laminar flow and in the laminar turbulent transition region, will be presented and compared with the theoretical analysis of laminar turbulent transition for flow between parallel plates. THEORETICAL ANALYSIS PIPE FLOW The mathematical analysisl-4 of laminar flow of a Bingham plastic fluid leads to the following equation. where q = <v>/R is a pseudoshear rate, rw is the wall shear stress Eo = r0/rw, r0 is the yield stress and 1 is the coefficient of rigidity or plastic viscosity from Eq. 1. Caldwell and Babbitt2-4 recognized that the quartic term in Eq. 2 was small compared to the other terms whenever 5, « 1, and that for large values of 7, a plot of Eq. 2 becomes linear. The slope of such a plot with rw as ordinate is 4? and the intercept is (4/3) ro. This approximation is illustrated schematically in Fig. 1. The shaded region between the true curve and the straight-line approximation near the origin represents the contribution of the quartic term. In principle, therefore,

By Charles G. Yale

(San Francisco Meeting, October, 1911.) A FEW years ago somebody connected with one of those self-constituted bodies of unofficial character, like a Chamber of Commerce, Board of Trade, or State Development Board, started a catch-phrase referring to California as " The Land of Sunshine, Fruit, and Flowers," and the railroad magazines and folders keep it steadily in use, working day and night. Yet it altogether ignores the substance which brought the State into the Union, which peopled it, and which made it famous through-out the world. You ladies and gentlemen who have come from what we here call "the East," have in your own States, no matter which one, sunshine, fruit, and flowers. But your Eastern States, having these things as we do, have not the gold that we do. Therefore, the old designation of "The Golden State," applied to California, should be revived, as being the most distinctive term. It is worthy of remembrance, too, that during the dark days of the civil war this State handed over $172,000,000 in yellow gold, and saved the credit of the nation. Gold-mining has been carried on in California since " The days of old, The days of gold, The days of 49," and it still continues. Since that historic year, and up to the end of 1910, the State has produced, in gold alone, $1,530,214,468. Since 1792 the entire United States production of gold has been $8,261,573,500, so that the single State of California has, in that period, produced within $201,144,564 of one-half of all the gold from Alaska, Arizona, Colorado, Idaho, Montana, Nevada, New Mexico, Oregon, South Dakota, Utah, Washington, and the Southern and scattering States. In other words, all the other 25 gold-producing States of the United States combined

Mar 1, 1912

By WILKES BARRE

AS PREVIOUSLY announced, the semi-centennial meeting of the Institute is to be held at Wilkes-Barre, Pa., on Sept. 12, 13, 14, and 15. An interesting program of technical sessions and excursions is now being prepared by the Local Committee. At the time of going to press the program had not been completed in sufficient detail to permit its being pub¬lished in this number. The detailed program will be published in the September MINING AND METALLURGY, which will be printed in time to be distributed before the Wilkes-Barre Meeting. It may be said in advance, however, that the Com¬mittee has progressed so far in its work that we are assured of one of the -most notable meetings the Insti¬tute has held and that members will miss a rare .treat if they do not attend. The many trips and excursions, as well as the banquet, will be -given to the members as a compliment from the members of the Local Com¬mittee. . . The paper by Howard Eavenson on the Lynch Plant of -the United States Coal and Coke Co. will be illustrated by lantern slides and moving pictures. One of the most appropriate discussions will be that opened by Prof. J. F. Kemp on the Stratigraphy of the Anthracite Region; this also will be amply illustrated.

Jan 1, 1921