Search Documents

By W. M. Hirthe, E. H. Greener, D. R. McCann

It has been proposed1'2 that, at low temperatures, point defects are a strengthening factor in inter-metallic compounds whereas, at high temperatures, the deformation is diffusion-controlled and, therefore, an increase in the concentration of point defects tends to soften or increase the plasticity of a compound. More recent investigations, including those of Bloem and Kroger' on PbS, Kramers and smith4 on TiO, and Nadeau5 on LiF, have extended this concept to ionic crystals. Rutile (TiO2) is a tetragonal transition metal oxide which has a defect structure over at least the compositional range. The defect in near-stoichiometric rutile is either an oxygen ion vacancys or a titanium ion interstitial.' This investigation does not contribute to resolving the defect question but either defect would satisfy the results obtained. Six specimens having the same orientation, see Fig., 1, utilized in an independent investigation1' were cut with a diamond saw from a single-crystal boule purchased from the Linde Co. Three specimens were annealed in air at 1200°C for 4 hr and slowly cooled to room temperature in a period of 12 hr. The remaining specimens were reduced in a vacuum of l0 mm Hg at 1200°C for 4 hr and cooled at the same rate in vacuum. The reduced specimens were weighed before and after reduction and, assuming the weight loss to be oxygen, the corresponding oxygen-to-metal ratio is 1.998. All specimens were chemically polished and etched utilizing the techniques described by Hirthe, Adsit, and Brittain." The specimens were embedded in acrylic resin and mounted on a leveling vise in a Kentron micro-hardness tester. A 200-g load was applied to a Knoop indenter with a descent time of 18 sec and a dwell time of 20 sec. Eight indentations were made on a near (171) surface, approximately 3 deg from the (lii) plane, for each orientation of the major axis of the indenter relative to the crystal structure. The dependence of microhardness on orienta-

Jan 1, 1963

By Thomas M. Plouf

Flotation, as we know it today, is a physiochemical method of concentrating finely ground ores. The process involves chemical treatment of an ore pulp to create conditions favorable for the attachment of certain mineral particles to air bubbles which are carried to the surface of the ore pulp for removal. Frother reagents, combined with air and the agitation mechanism, produce the effective bubbles in a flotation cell. A method of analysis is presented to evaluate the effect of frother reductions and additions on a bank of flotation cells, and to economically determine if and to what extent frother reductions and additions are justified. Comparative evaluations of different frother systems, as well as the amount of frother used in a given flotation machine, cannot be made on the frother cost alone. An indepth study must be made to evaluate any given frother as applied to a particular ore body. The recovery of a given mineral is as dependent on the amount of frother as on the type of frother used. An actual case study follows in which the amount of frother required by two different flotation machines was used to make a decision as to which unit performed more efficiently based on costs. This same method may be used to evaluate new frothers as well as to determine if a larger frother addition is advisable.

Jan 11, 1975

By L. de Florez

The successful control of any operation, whether industrial, military, or purely physical, is fundamentally dependent upon the same elements: (I) The securing of accurate and pertinent information concerning the factors involved in the operation; (2) Correct interpretation of their relationship as affecting future results; (3) Efficient means for effecting changes in the factors governing the operation to shape the result. The analogy which exists in the control of operations in these widely differing fields of action is of utmost interest, and in considering the physical control of a process, the realization of its existence permits a clearer conception of the steps required to achieve results and aids in formulating the problems to be met. Let us imagine, for instance, the requirements for successfully conducting a business. It is evident that the first requisite lies in obtaining continuous and reliable information concerning the functioning of its various branches and in detecting, with the least possible delay, any tendency of change in their functions; next, in correctly analyzing this information by comparison with past records, showing the relation of the particular business to general conditions in the trade; and finally, in employing means for counteracting any unfavorable change in general conditions, or compensating for its effects by an appropriate action. Likewise, in military operations, the success in carrying out a plan lies primarily in the maintenance of proper intelligence and communication service, which furnishes information as to the disposition of forces; in correct analysis of the ascertained position, guided by fundamental knowledge of tactics; and finally, on the efficient carrying out of orders and effecting corrective movements. In the physical operation of a process, such as for example in cracking, our information is obtained by pressure and temperature instruments, etc., which permit us to visualize existing conditions under which the operation is being carried out. The information at hand is then analyzed and certain conclusions arrived at as to the results which will be obtained under the observed conditions. If this analysis should indicate, in the

Jan 1, 1928

By L. Edeleanu

Crude petroleum is a mixture of various groups of hydrocarbons and some bodies containing oxygen or sulphur.

Jan 1, 1915

By William E. Bonini, Eugene A. Hickok

IN the course of an investigation directed toward expanding ground-water facilities in Essex and Morris counties, New Jersey, the Board of Water Commissioners of the city of East Orange authorized a seismic-refraction survey1 for the purpose of delineating bedrock topography below unconsolidated overburden. Results of the survey were highly satisfactory and led to the preparation of a comparatively detailed bedrock contour map. Knowledge of the bedrock depth and configuration was an important aid in selection of sites for test drilling. The portion of the East Orange Water Reserve under consideration is in the flood plain of the Passaic River about 10 miles west of Newark, N. J. The flood plain is about 175 ft above mean sea level and is bordered by low hills rising to elevations of approximately 250 ft. The bedrock underlying the Water Reserve consists of sandstone and shale of the Triassic Brunswick formation and is covered everywhere by deposits of unconsolidated glacial outwash sand and gravel, lacustrine clay, and recent river silt as much as 150 ft thick. Yield of wells in the sandstone and shale averages 100 to 200 gpm. Since production wells constructed in the sand and gravel aquifer in the buried river valley shown on the contour map (Fig. 1) yield 300 to 1400 gpm, it was proposed to locate additional production wells in this buried valley, where the yields per well would be maximum.

Jan 4, 1958

By George K. Burgess, Robert A. Hadfield

1. Introduction.—The methods of production of sound steel ingots have been described in several papers read recently before this Institute. It was thought by Director Stratton, of the U. S. Bureau of Standards, and ourselves to be of sufficient interest and importance, as a further contribution to this subject, to compare the properties of rails rolled in one mill according to American practice, from several types of ingot of substantially the same chemical composition but cast by several processes; and to compare in considerable detail the properties of an ingot manufactured by the Hadfield special-feeding process and one of the usual type for rolling into rails. We are greatly indebted to F. W. Wood, President of the Maryland Steel CO., who made this investigation possible by kindly placing his rail mill at our disposal; and he and his associates at Sparrows Point did everything possible to make the experiment a success, including the execution of several of the tests and analyses. 2. Classification and Manufacture of Ingots.—Of the ingots used in this investigation, eight were made in Sheffield and furnished by Sir Robert Hadfield, and one was made and furnished by an American steel company,l as a comparison ingot, and was supposed to represent the usual type of ingot from which rails are made. The characteristics of the ingots are given in Table I. Ingots 1, 2, 3, and 4 were cast large end up and fed by the Hadfield method in the usual manner with charcoal and blast continued until the molten steel has set on the top of the head, say varying from 20 to 40 min. To ingots 1, 2, and 4 was added 0.1 per cent. aluminum, and to the nickel-chrome ingot, No. 3, 0.125 per cent. For sake of comparison, there were also included two ingots, Nos. 8 and 9, cast with the small end up and fed by

Jan 1, 1915

By E. B. Burwell, R. H. Nesbitt

Designed by army engineers, the NX borehole camera provides the most economical method of subsurface exploration so far devised. Continuous cylindrical color photographs now reveal minor flaws in foundation bedrock not always disclosed by borehole samples. A unique projector transforms the photographs into true-to-scale images of three dimensions. ANEW milestone in the progress of photography and subsurface exploration was reached when the Chief of Army Engineers announced the development of the NX borehole camera. In obtaining continuous undistorted cylindrical color pictures of dry or water-filled borings the device surpasses all other cameras designed for photographing interior surfaces of pipes, wells, and conduits. The usefulness of the camera and the unique projector that comes with it are at once apparent. To the geological, mining, and civil engineer alike it signifies the end of guesswork with respect to underground conditions that have eluded identification by conventional core-drilling methods. To the medical profession it may well signal new progress in photo optics which could result in cylindrical color photographs supplementing the X-ray and existing photographic methods used in exploratory surgery. The pilot model of the camera has more than paid for itself as a result of its success in bringing to the surface at two dams information previously obtainable only by costly drilling of mansized boreholes for subsurface on-the-spot examination. Such bores cost as much as $200 per lineal foot as against $10 per ft for the conventional 3-in. or NX exploratory core borings from which the present invention derives its name. The NX camera can now photograph completely the interior surface of these borings. Research and development for the first camera and projection equipment were conducted by Engineering Research Associates, Division of Remington Rand, Inc., under the technical supervision of the Geology and Geophysics Branch, Office of the Chief of Army Engineers in Washington, in accordance with plans and specifications furnished by this branch. Subsequent modifications of the camera-lowering device, transporting equipment, and special field tools were made in the Corps of Engineers' Ohio River Division Laboratories in Cincinnati. The background of this development is interesting. Among the more difficult foundation problems involved in construction of concrete dams are those resulting from bedrock imperfections that escape disclosure by conventional exploration methods. Often these imperfections are of sufficient magnitude to introduce costly changes, especially when their presence is discovered only after foundation excavation is well in progress. Bedrock flaws most frequently camouflaged may be ruptures resulting from the enormous stresses to which rocks have been subjected, or they may be planes or zones of weakness related to chemical alteration and underground erosion. Obviously, detailed information on their location, dimensions, and structure is important, as these factors can affect the stability of a dam and the security of life and property downstream. Their discovery and appraisal entail extensive subsurface exploration. At present the most economical exploratory tool available to geologists and engineers is the small-diameter diamond core drill by means of which cores of the foundation bedrock are recovered for examination and testing. All too often, however, these samples fail to disclose minor foundation flaws that may be of major importance before a structure is completed. As a result, the small-diameter drillings are supplemented generally by more reliable but much more costly shafts, tunnels, or large-diameter calyx drill holes that permit the investigator to examine the foundation rocks in place. It was to reduce the number and cost of these expensive and time-consuming investigations, as well as to obtain more complete information on rock structure from the smaller borings, that the NX borehole camera was developed. That it has been eminently satisfactory in accomplishing that purpose is demonstrated by its success most recently at the Folsom dam, under construction on the American River, 23

Jan 1, 1955

By Cyril Wells, Robert F. Mehl

THE practical importance of a knowledge of the rates of diffusion of carbon and of alloying elements in steel has often been pointed out 1,13 This importance ties chiefly, though by no means only, in the study of carburizing and in the study of reactions involved in the eutectoid inversion in steel The present paper is one of a series in which the rates of diffusion of carbon and of alloying elements in y-Fe and their mutual effects are measured with precision The present paper reports the results of meas¬urements of diffusion coefficients D of manganese in -y-Fe over wide ranges of temperature, and concentration, and of the effect of carbon and impurities and of grain size upon these diffusion coefficients [$] Data on the rate of diffusion of manganese in y-Fe have been reported by Fry2 and by Paschke and Hauttmann 3 Claussen4 calculated the diffusion coefficient D from Fry's data as 3 X 10-10 sq cm per sec at 960°, which will be shown to be incorrect by many orders of magnitude Paschke and Hauttmann gave a rough value of 9 6 X 10-8 sq cm per sec at 1400° Neither of these workers considered the variation of D with concentration and with temperature, and neither studied the effect of carbon METHOD AND MATERIALS Method -The method employed is identical with that used earlier 5 Owing to the volatility of manganese and the consequent loss of manganese from the outer surfaces of the welded diffusion bars, these surfaces were discarded The diffusion anneals were performed in argon, except one (test 18) in which hydrogen was employed for purposes noted below The temperatures reported are accurate to about 3° and constant within I°C , the diffusion times are reported to the nearest half hour The specimens were furnace-cooled after the diffusion anneal at about 2° per min Layers, usually 0 004 in thick, parallel to the welded interface, were machined from the specimens after the diffusion anneal and analyzed for manganese to 0 01 per cent Mn, the distances of these layers from the interface was measured to ±0 0002 in The concentration-penetration curves obtained were analyzed by both the Grube and the Matano solutions e The D values calculated by these two methods do not differ appreciably 5 The Grube solution was used except in tests in which the effect of concentration upon D was greater than 50 per cent, in such cases the Matano method, which explicitly provides for the variation of D with concentration,1 is the more reliable In general, the number of layers machined from the zones of variable composition were large enough to permit the use of the average layer composition as that of the center of the layer In 3 of the 30 tests, however, this is not justified, and the D values

Jan 1, 1941

By Charles C. Russell, Glenn C. South

A primary factor in the selection of coals for making coke at high temperatures is the amount of pressure the coal will exert upon the oven walls when carbonized in modem by-product ovens.l-3 This factor has become increasingly important in recent years because of demands for increased throughput and higher coke yields. As a result of the increasing necessity for assessing coals in regard to their carbonization pressures, more and more research work is being directed toward developing labora-tory-scale tests for predicting carbonization pressures and for showing how blends of coking coals may be modified to eliminate pressures liable to damage coke-oven walls. The specific reasons have never been defined as to why some blends of coking coals develop dangerous carbonization pressures and others do not, therefore specific procedures to eliminate dangerous pressures could not be prescribed. It is true that the major processes occurring during carbonization have been described by many writers,4 and there is a general agreement on the ideas of the changes that occur as coal is transformed into coke. However, there is little evidence relating the processes occurring during carbonization to the pressure developed and the available evidence is very incomplete and often contradictory. This deficiency arises in part from the fact that the fundamental causes of pressure development have not been defined, at least from experimental data, and in turn this is the result of the lack of satisfactory testing equipment for studying the problem. Operating experience has shown several ways of reducing or eliminating dangerous pressures,5 but probably none of these ways is applicable to all blends of coking coals, and such empirical methods often lead to production of inferior coke. They are trial-and-error methods, not designed to remedy specific causes of pressure development. The number of laboratory-scale testing devices designed to estimate the carbonization pressures that result when coals are carbonized in commercial ovens is probably well over a hundred.6 Few of these instruments have remained in use for any length of time, either because the predictions were not sufficiently accurate or, more often, because too many exceptions were found. Often testing devices are operated without any attempt at duplication of conditions in commercial ovens and erroneous and contradictory results are frequently obtained. Therefore, it has seemed desirable to study the properties of coal itself and to determine any relationships between the properties of the coal and the carbonization pressures developed. Relationship between Properties of Coal and Carbonization Pressure Attempts to determine relationships between various properties of coal and carbonization pressures, for the most parti have been indirect because no satisfactory and reliable laboratory testing device has

Jan 1, 1944

By Glenn C. South, Charles C. Russell

A primary factor in the selection of coals for making coke at high temperatures is the amount of pressure the coal will exert upon the oven walls when carbonized in modem by-product ovens.l-3 This factor has become increasingly important in recent years because of demands for increased throughput and higher coke yields. As a result of the increasing necessity for assessing coals in regard to their carbonization pressures, more and more research work is being directed toward developing labora-tory-scale tests for predicting carbonization pressures and for showing how blends of coking coals may be modified to eliminate pressures liable to damage coke-oven walls. The specific reasons have never been defined as to why some blends of coking coals develop dangerous carbonization pressures and others do not, therefore specific procedures to eliminate dangerous pressures could not be prescribed. It is true that the major processes occurring during carbonization have been described by many writers,4 and there is a general agreement on the ideas of the changes that occur as coal is transformed into coke. However, there is little evidence relating the processes occurring during carbonization to the pressure developed and the available evidence is very incomplete and often contradictory. This deficiency arises in part from the fact that the fundamental causes of pressure development have not been defined, at least from experimental data, and in turn this is the result of the lack of satisfactory testing equipment for studying the problem. Operating experience has shown several ways of reducing or eliminating dangerous pressures,5 but probably none of these ways is applicable to all blends of coking coals, and such empirical methods often lead to production of inferior coke. They are trial-and-error methods, not designed to remedy specific causes of pressure development. The number of laboratory-scale testing devices designed to estimate the carbonization pressures that result when coals are carbonized in commercial ovens is probably well over a hundred.6 Few of these instruments have remained in use for any length of time, either because the predictions were not sufficiently accurate or, more often, because too many exceptions were found. Often testing devices are operated without any attempt at duplication of conditions in commercial ovens and erroneous and contradictory results are frequently obtained. Therefore, it has seemed desirable to study the properties of coal itself and to determine any relationships between the properties of the coal and the carbonization pressures developed. Relationship between Properties of Coal and Carbonization Pressure Attempts to determine relationships between various properties of coal and carbonization pressures, for the most parti have been indirect because no satisfactory and reliable laboratory testing device has

Jan 1, 1944

By H. T. Lundberg, J. H. Ratcliffe

In airborne gravity surveys effects of acceleration and irregular movements of the aircraft must be balanced out or overcome. The gradient of vertical gravity is recorded, therefore, by using two masses instead of one. As the amplitude variations are infinitesimal and difficult to measure accurately, at present it is enough to determine whether variation of gradient during flight is positive or negative. The positive portions of the pattern can then be indicated and contoured. Even with these simplifications, the source of energy must be exceptionally stable. General Principles: In the conventional gravi-meter the weight of a standard mass is determined at a number of selected points within the survey area. In most systems weight is determined by comparing the gravity pull with extension or torque

Jan 1, 1960

By A. R. Gregory, M. R. J. Wyllie

The literature reveals that scant attention has been paid to the systematic experimental determination of the formation factors of unconsolidated porous media. No experiments appear to have been made on the effect of increasing cementation on the formation factor of an initially unconsolidated porous medium. Measurements have accordingly been made of formation factors as a function of porosity for aggregates of spheres in the porobity range 12-56 per cent and of cubes, cylinders, discs and triangular prisms in the porosity range 30-45 per cent. The results are examined in the light of the theoretical equations of Clerk Maxwell. Fricke and Slawinski. Aggregates of unconsolidated spheres and beach sands have been artificially cemented with silica and the formation factor-porosity relationships determined. A theory is outlined which seeks to explain the results obtained and which postulates that formation factor and porosity data for consolidated sandatones may be used to determine the original porosity of the unconsolidated sands from which the consolidated sandstones were derived. It follows also that for consolidated sandstones F' = C where F is formation factor, fractional porosity and C and k are constants. INTRODUCTION All schemes of electric log interpretation implicitly or explicitly require the use of formation resistivity factors or? as they are now generally called. formation factors. 'The originator both of the concept of formation factor and of the use of formation factor data in electric log interpretation was Archie.' More recently it has been suggested that formation factors are of value in describing fluid flow in porous media. A full discussion of this problem together with adequate reference.: has been given by Wyllie and Spangler.' In spite of the theoretical and practical importance of the subject, there appear to be remarkably few basic formation factor data in the petroleum literature. A wider search reveals that this situation is nut confined to the literature of the to industry. at various times over the last century, attempts have been made to compute the theoretical relationship between the formation factor and porosity of simple systems of unconsolidated particle.. However. the formulae derived are not all identical and the experimental evidence adduced in support of each i; not wholly convincitng. Most of the experimental work has been carried out on system. of unconsolidated spheres, although some attention has been given to systems of spheroids and cylinder. Other simple shapes have received neither theoretical nor experimental investigation. The writers feel that a better understanding of the formation factors of complex systems of practical importance requires a firm foundation of reliable experimental data applicable to simple systems. Accordingly, they have reviewed the relevant literature and have determined experimentally the relationship between the formation factor and porosity of unconsolidated aggregates of particles of regular geometrical shapes. Some experiments have also been carried out to investigate the effect of cementation on the formation factor-porosity relationship. PREVIOUS WORK Although the term formation factor was not used. the relationship between the resistivity of a solution containing dielectric solids and the resistivity of a similar solution not containing solids is an old and important problem. The formation factor of a system of dispersed spheres as a function of porosity was considered by Clerk Maxwell. Maxwell arrived theoretically at the following expression: where F is formation factor and fractional porosity. Lord Rayleigh' also examined the problem of the formation factor of systems of spheres and cylinders and concluded that for spheres Clerk Maxwell'.; expression gave a value of F whirl]. at low porosities particularly, was too small. However,

Jan 1, 1953

By William R. Webster

In view of the great interest now taken in the tests of castiron and details of foundry practice, with the number of investigators at work, and recent improvements in the methods of research, it would seem that the time is ripe to attempt the solution of some of the many problems with which iron founders have to contend. Recent papers and discussions on these subjects* have opened up s large field for investigation, and have emphasized the importance of many considerations generally overlooked. With the view of promoting a comprehensive and systematic discussion, I have attempted to tabulate, in conveilient form, some of the most important points for investigation, on the general plan suggested, with such good results, by our former President, H. M. Howe, for the discussion on the Physics of Steel, at the Virginia Beach meeting, last year. This table can, no doubt, be modified or enlarged to advantage, and put in shape to serve as a guide or reminder to all who are interested in this line of work. Suggested Lines for Discussion and Investigation. I.—Correspondence between chemical composition and melting point, fluidity, shrinkage, fracture, chill, micro-structure, and other physical properties. II.—Influence of: I. Cupola mixture, use of steel and other scrap, oxidized or clean material, 2. Manner of melting, flux, etc., 3. Casting temperature, A. Fracture. 4. Manner of handling melted metal and B. Micro-structure. method of casting, C. Physical properties. 5. Size and form of casting, D. Shrinkage. 6. Kind of mould, green sand (under dif- on 1 E. Chill. ferent conditions of ramming, amount F. Residual stress. of moisture, and skin-dried), dry sand, G. Condition and quan loam, and chills, tity of carbon and 7. Rate and mode of cooling castings, other elements. 8. Manner and temperature of heating for annealing, 9. Additions of nickel or aluminum,

Jan 1, 1896

By K. D. Jacob, W. L. Hill

THE bulk of natural phosphates is comprised of calcium phosphates, which are usually apatites;1 calcium aluminum phosphates such as pseudowavellite;2 and aluminum phosphates, which occur in extensive deposits, notably on Grand Connetable Island.3 Nearly all deposits of current commercial value are apatite, often with admixed material of other classes. In the trade coarsely crystalline material, mainly fluorapatite of igneous origin, moves as apatite, whereas the fine-grained material of sedimentary origin is marketed as phosphate rock. The latter classification includes the phosphate shales in western North America. Although several genetic varieties of phosphate rock are recognized,4 most known reserves are of marine origin. Calcium phosphate is concentrated from Florida land pebble and Florida hard rock deposits and from Tennessee brown rock deposits. Phosphate Rock as a Fluorine Carrier: More than two decades ago Reynolds and Jacob surveyed the fluorine content of commercial phosphate rock from various parts of the world.3,5 Later these samples were reanalyzed by a new and more reliable method of determining flourine.6,7 The revised results with interim additions of new samples, published a few years ago in a brief summary,' are shown in Figs. 1-3. Through the points representing the respective varieties of rock medial straight lines are drawn. In some instances the lines are well defined by the points; in others, where scattering renders the position of the best line uncertain, the greater weight is given points near the end of the covered range. Wherever distinct varieties are not recognized among regional deposits the custom is to identify the sample with the geographical location of the deposit.

Jan 10, 1954

By W. J. Sharwood

Discussion of the paper of W. J. SHARWOOD, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 104, August, 1915, pp. 1671 to 1675. FREDERIC P. DEWEY, Washington, D. C. (communication to the Secretary*).-Even if the data given should be considered sufficient to support properly the empirical rule as stated, this rule would be of extremely limited application in miscellaneous assaying. Tile fixed conditions must include equality of gold and silver where mixed beads are concerned, owing to the wide variation in the specific gravity of gold and silver. Also, the fixed conditions must include the presence of the sane amounts of other base metals besides lead. Such an agreement is .often lacking even in the beads from two fusions of the salve ore. In practical work it is sufficiently general to be called universal that cupellation beads are not pure precious metal. An apparent loss in cupellation is an algebraic sum and in many cupellations the gains exceed the losses, especially with large beads where tile gains lie so completely in the judgment of the cupeller. For several years I have been engaged in an investigation into the conditions affecting the accuracy of gold-bullion assaying, and have just completed an examination of cupels which included the assaying of 10,000 used cupels. The grand result of the cupel work is an emphatic warning against drawing rigid conclusions regarding cupellation. It is so easy to say "If all other conditions remain the Same," but it is extremely difficult, and in practical work impossible, to maintain equal conditions. Cupel absorptions, which constitute such a large proportion of cupellation losses, and in many cases the only loss, may vary considerably in different parts of the same row of cupels, even in carefully regulated work.

Jan 12, 1915

By Henry Fay

LAWRENCE ADDICKS, New York, N. Y., (communication to the Secretary *).-There are two points regarding gun erosion on which I want to say a few words: The first is about the analogy to hardening of wire by drawing and the second the possible role played by thermal conductivity of the metal. The ductile metals do not necessarily become brittle when cold-worked as it is possible to draw copper from 3. in. in diameter soft rod down to the finest hair wire without annealing. This results, as stated in the paper, informing a hardened core with a very hard skin. The electrical conductivity is depressed some 3 per cent. and the tensile strength nearly tripled. A soft copper wire 0.08 in. in diameter and 6 in. long may be twisted 150 or more turns before the wire will snap under torsion. A hard-drawn wire will break after perhaps a dozen twists, the skin breaking down at one spot. Just wiping the wire with a cloth clamp with dilute nitric acid has a remarkable effect in increasing the number of twists without appreciably lowering the tensile strength, showing the skin to be very thin. On the other hand, pickling the rod, from which the wire is to be drawn, in dilute nitric acid also greatly increases the number of twists which can be applied to the resulting wire. This indicates that the copper oxide scale produced when the wire bar is rolled hot is more or less rolled into the rod and may have much to do with the skin effect. We also know that if the conditions of drawing are not correct, the heat of deformation in the die may produce quite an annealing effect. The application of this analogy to what occurs in a gun to produce the effects noted offers some difficulty. The second point is that as the temperature of the surface of the gun bore has undoubtedly a great deal to do with the amount of erosion, one natural remedy would be to conduct the heat away fast enough to keep this temperature within desired limits. This brings up the question of the thermal conductivity of the metal of which the gun is made. We know that the conductivity of pure metals is greatly altered by alloying and that the alloy is usually, though not always, lower in conductivity than the metal before alloying. This is interesting when it is considered that the high-nickel and manganese-steel alloys show greater erosion as stated. Would it not be instructive to study the question from the point of view of heat conducted away from the eroded surface?

Jan 3, 1917

By M. E. Wadsworth, G. W. Warren

INTRODUCTION Hydrometallurgical processes for the extraction of metal values can be divided into two broad categories: (a) Processes involving the treatment of high grade material (e.g. finely divided mineral concentrates); and (b) processes which treat lower grade material (ores, waste dumps, etc.). This discussion will be directed primarily toward the first category, but in either case a fundamental knowledge of the intrinsic kinetics and thermodynamics is necessary to understand the behavior of the system. The bulk of research efforts in the last decade along these lines has been aimed at the recovery of copper (1-8). However much information has also been reported on uranium (9, 10) , zinc (11) , cobalt and nickel (12, 13). More comprehensive reviews on these areas are also available (14). As discussed by Sepulveda and Herbst (15, 16) one of the most difficult problems facing process designers is the acquisition and scale-up of reliable information concerning the intrinsic kinetics of leaching systems. The scale-up or modeling of these multiparticle systems is far more complex than that of homogeneous ones. This is due to the numerous rate determining steps which are possible with heterogeneous reactions and the broad distribution of properties of a multiparticle feed such as particle size and mineralogical composition (16). In addition, other factors must also be considered such as interactions between particles, the anisotropic nature of individual particles, the effect of solution chemistry, and electrochemical phenomena. All of these factors must be taken into account, often simultaneously. The thrust of this paper will be to more closely examine how the factors mentioned above can be treated. Some elementary examples of

Jan 1, 1980

By H. R. Froning, R. O. Leach

In wertability alteration flooding, a chemical agent is rnoved through a reservoir by the flood water to increase oil recovery by decreasing the degree of wetting of the rock by the oil. Substantial amounts of the chemical may be lost during movement through the reservoir. The extent of the loss, and therefore the economics of the process, depends in some cases on factors which are difficult to reproduce in the laboratory. Therefore, a short-duration, low-cost field test method is needed to permit evaluation of chemical requirements under actual field conditions. This paper describes a small scale rest conducted at a single well for measuring chemical requirements, thereby giving a more reliable evaluation of this important factor in the applicability and economics of the process. In the rest a small wafer slug containing the chemical agent and a nonadsorbed tracer is displaced into the reservoir by a known volume of wafer. The well is then placed on producrion. Chemical loss per barrel of pore volume contacted is calculated from [he fractional recoveries of the agent tested and the nonadsorbed tracer. The method has been used to determine within the actual reservoirs the chemical requirements for both a sandstone and a dolomite reservoir. Several chemical agents are potentially available for wettability alteration flooding, although none is universally applicable. For some applications of the method, chemical costs per barrel of additional oil recovered can be substantially less than one dollar. INTRODUCTION Wettability alteration flooding provides a means of increasing oil recovery from reservoirs by decreasing the degree of wetting of the rock by the oil and increasing the displacement efficiency of the flood water. Earlier studies demonstrated a relationship between oil recovery during waterflooding and the degree of wetting of a rock surface by an oil. The application of wettability alteration flooding to the Harrisburg field of Nebraska provided a field test' of this recovery process. Subsequently, additional laboratory and field tests have developed additional procedures for evaluating wettability alteration flooding, and have indicated where the process may be applicable. Applicability of this process to specific reservoirs is determined by a progression of tests to determine sus- ceptibility of the reservoir to alteration of its wettability, to indicate the degree of recovery improvement and to estimate the amount of chemical required to process the reservoir. The economics of applying improved oil recovery processes depends not only upon the degree of improvement in oil recovery achievable by the process but also upon the process costs and the timing of the income and the investment. Emphasis in this paper is on the expenditure aspects of the process. The work reported in this paper indicates that the chemical investments required for wettability alteration flooding are substantial. For evaluating the economics of a potential flooding application it is imperative that a sound estimate of the chemical requirements be made for the reservoir. Generally, true reservoir conditions are not adequately simulated in laboratory chemical propagation tests. Because of wide well spacings, many years might be required to obtain chemical propagation data from conventional pilots or inter-well tests. Consequently, n short-duration, low-cost method is needed to determine chemical requirements in the field. The potential applicability of wettability alteration flooding is discussed, as well as the economics of wettability alteration with respect to the inherent and imposed restrictions on the timing of income and investments. DETERMINATION OF CHEMICAL REQUIREMENTS In the process of moving a chemical bank through reservoir rock, some of the chemical agent lags too far behind the flood front to be effective or is otherwise lost to the reservoir system. The extent to which these losses occur overshadows the reductions in chemical concentration due to diffusion and to mixing with the reservoir fluids. Experience indicates that almost without exception, chemicals which induce a wetting change undergo either sorption reactions or chemical reactions with mineral constituents of the pore surfaces. Other reactions may occur between the added chemical and the reservoir oil and water. Even in limiting consideration to reactions of the relatively inexpensive inorganic salts, bases and acids, the reactions may be exceedingly complex. Reservoir pore surfaces consist of more than silica in sandstone reservoirs, and more than calcite or dolomite in carbonate reservoirs. Many mineral species are present, each exhibiting specific tendencies to react with an injected chemical. The reactions which occur can consume enough of the agent to have an important effect on economics. These reactions can cause a change in pH of the chemical bank, or may remove some of the active chemical by precipitation, adsorption or reaction to form a new chemical which may or may not be effective in

By F. R. Wadleigh

It is generally realized and very often admitted by both producers and consumers of coal that there is great need for a revision of existing commercial classifications, and this will involve, of course, determination of a standard classification and a constant revision of marketing practices as they are affected by coal classification. I recently sent out some 200 letters to producers and consumers with a request for their views on the subject of commercial classification. Nearly all of the replies from both sides were that there was needed some change in the present method. There were three or four dissenting voices but the great majority of opinion was in favor of the formulation of some standard commercial classification. The classifications in commercial use today can best be described as a hodgepodge. They are made upon different bases, have different names and have different ways. There are, for instance, about 11 single bases of classifications as used commercially and some 17 or 18 combination bases. Then there were the Tidewater Pool Exchanges. The classification which they put in force is still used in the tidewater markets and has several different bases of its own. It will be considerable of an undertaking to bring about a change in marketing methods as affected by coal classification but it is well worth doing and I think the committee which has been appointed under the auspices of the American Society for Testing Materials realizes the importance of the subject and is on the way to at least bring about some provision for adjusting matters. By way of starting, each member of the Committee on Commercial Classification has been assigned to a general market district and each member is now engaged in collecting the commercial market practice data for submission at the next meeting of the Committee. About a year ago I made up a list of the commercial classifications in the different markets and the total was 171. The 11 single bases I found used in commercial practice were:

Jan 1, 1930

By John E. Latz

QUICKSAND far below the surface, stopped two attempts by the Potash Co. of America to sink a third shaft to a potash bed that lies 1000 ft below the southern New Mexico desert. Virtually all methods of grouting were employed in the two failures without any indication of consolidation of the flowing sand. Sinking the South Shaft at the Carlsbad potash mine seemed an almost insurmountable task, until freezing was employed as a final resort. This process that proved to be the answer may be defined as "the sinking of a shaft by freezing, consists of the formation, in the water-bearing strata, of a large block of frozen ground in which it is possible to sink a shaft without danger of an influx of water, providing the ice-wall between the water outside and the shaft itself is strong enough to resist the hydrostatic pressure." Freezing Method Used Extensively in Europe Successful frozen ground shaft sinking projects had been completed in Europe, and Russel G. Haworth, resident manager of the Potash Co. of America, went abroad in search of the know-how needed for the New Mexico undertaking. The freezing process, with a history of two failures at the time, was first successfully employed by Poetsch in 1885 at the Houssu Collieries near Haine St. Pierre, Belgium. Poetsch contracted to sink the remaining 64 ft of an uncompleted shaft through water laden strata from a depth of 190 ft to a depth of 254 ft. This work was in progress until 1887. The freezing and sinking consumed more than two years. As a result of early failures, the process was not favorably received until soon after the turn of the century. The accurate prediction of success in a given application was made possible by the concerted effort and study of a group of European engineers. Means of accurate deviation measurement and control were devised, the nature and properties of frozen water laden soil (the ice wall) were investigated, a thorough and rational basis of refrigeration load calculation developed, and concurrently the efficiency and dependability of refrigeration machinery was greatly advanced. Numerous shafts in Germany, Belgium, France, and England today testify to the reliability and economical surety of the freezing method. Applied to the South Shaft, which is circular in cross-section and 15-ft diam, the freezing method consisted of drilling holes 350-ft deep, through the water bearing strata into impervious ground-the freeze hole pattern being concentric with the shaft and 31-ft diam. The holes were cased with pipe closed on the bottom end. Smaller tubes were placed inside these casings and connected to a header supplying chilled brine from a refrigeration plant. The brine descended in the tubing to the bottom of the hole and ascended through the annular space between the two pipes to the top of the casing; flowed into the return header and back to the refrigeration plant. Under these conditions, each of the freeze hole casings became surrounded by a cylinder of ice

Jan 1, 1952