Search Documents

By John A. Church

Jan 1, 1880

By A. J. Lyon

THE stability and permanence of any structural material used in aircraft are of paramount importance. The spontaneous hardening, or age-hardening; which takes place in some of the aluminum alloys under ordinary conditions of temperature and atmosphere, is accompanied by an increase in tensile strength and proportional limit and a decrease in elongation or ductility. Within the last few years the introduction of a number of strong and ductile casting alloys led to a study by the Materiel Division, Air Corps, of the permanence of the physical properties in several of these alloys. It has been found that even though some alloys have good properties directly after casting or heat treatment, they are not satisfactory for stressed parts that require a combination of strength and ductility. It has also led to the conclusion that all alloys that can be hardened by artificial aging-heating in a temperature range below 170° C. (340° F.)-will harden spontaneously if allowed to stand for a sufficient length of time. It follows that, in aircraft work where the factors of safety are limited on account of the necessity of keeping the weight of the structures as low as possible consistent with their safe operation, the properties of the alloys in the stable or final condition should be used as a basis for design rather than the properties obtained on the material directly after casting. The work of Wilm in Germany, Hanson and Gayler at the National Physical Laboratory in England, and Merica, Jeffries, and others in the United States, has shown that the spontaneous hardening is characteristic to a greater or less extent in all aluminum-base alloys in which the solubility in the solid state of the alloying constituents decreases with the temperature. It has been shown that, by heating to a temperature as near as possible to the melting point of the material and soaking at that temperature for a sufficient length of time and then quenching or cooling rapidly, a maximum amount of the soluble constituents can be retained in solution and the condition of maximum hardening effect upon aging can be obtained. Also, in ordinary sand and chill castings, without heat treatment, a sufficient amount of the alloying constituents is held in solution to cause important changes in the final physical properties.

Jan 1, 1928

By AIME AIME

INSTITUTE HEADQUARTERS, Hotel Statler. On Monday evening, Oct. 28, 1912, the visiting members and guests were informally received by the Local Committee at the Headquarters of the Institute at. the Hotel Statler. The evening was very pleasantly spent in renewing old acquaintances and friendships and in forming new ones. The first session, held Tuesday morning, Oct. 29, 1912, in the impressive Assembly-Room of the hotel, was called to order by David T. Croxton, Chairman of the Local Committee. Mr. Croxton introduced the Hon. Newton D. Baker, Mayor of Cleveland, who extended a cordial welcome to the members and guests present. James F. Kemp, President of the Institute, who subsequently presided at the meeting, responded in behalf of the Institute.

Nov 1, 1912

By AIME AIME

THE Charleston Section of the A. I. M. E. held a joint meeting with the National Coal Association and the American Society of Mechanical Engineers on May 6 and 7, at which 94 members and guests were registered. Mechanical operation of coal mines was the subject discussed. First on the program was a paper entitled "Rock Dusting in the Coal Mines of West Virginia," by R. M. Lambie, chief of the Department of Mines, and Gordon MacVean. It appears in full in the current issue of MINING AND METALLURGY, p. 290. J. E. Jones of the Old Ben Coal Corp. opened this discussion by describing the method of rock dusting employed in the mines of that company, giving many interesting details, incidentally referring to the use of rock dust in fighting mine fires. He described one case where a number of troughs was brought to within 150 ft. of the fire, and rock dust had been thrown in its direction. After each trough had been thrown the party advanced a few feet, where another trough was discharged. About 10 ft. were gained on each advance, until the party found they had advanced completely over the fire.

Jan 1, 1926

By F. W. Schremp, J. W. Chittum, T. S. Arczynski

This paper describes a laboratory study of causes of external casing corrosion and the test work that led to the use of oxygen scavengers to prevent this attack. External casing failures are classified as water-line, casing-casing, collar and body failures. A corrosion mechanism based on principles of differential oxygen availability is developed that is consistent with facts known about each kind of failure. The field use of oxygen scavengers is depicted as a direct result of the laboratory study. A part of the paper is devoted to reporting on the field use of hydra-zine to control external casing corrosion. Results of field measurements made over a period of several years are presented as evidence of the efectiveness of the hydrazine treatment. The first conclusion reached is that the use of hydrazine materially reduces the cathodic protection requirements for treated wells. This result is interpreted to mean that a reduction is taking place in the amount of corrosion on the casing. Results indicate also that hydrazine shows its greatest usefulness within the first 12 to 18 months after a well is completed when pitting corrosion is likely to be most active. INTRODUCTION According to surveys sponsored by the National Association of Corrosion Engineers,' the cost of repairing casing leaks caused by external corrosion may exceed $4 million per year. In addition, well damage and lost production resulting from casing leaks probably costs the petroleum industry an additional $5 to $6 million per year. Concern about the cost of external casing corrosion led to an extensive laboratory study of factors causing this external corrosion and to the development of a new approach to its prevention. This paper presents a discussion of various causes of external casing corrosion, details of laboratory studies and the results of the field use of an oxygen scavenger in well cementing fluids to prevent the external corrosion of oil-string casing. Measurements on test wells over a period of several years show that cathodic-protection current requirements are greatly reduced when hydrazine is used in cementing mud. Reduction of current requirements can be interpreted to mean that removal of oxygen by hydrazine has greatly suppressed corrosion cells on the external surface of the casing and thereby, has reduced corrosion. To date, hydrazine has been used by the Standard Oil Co. of California in more than 200 well completions. KINDS OF CASING FAILURES A survey of a large number of casing leaks disclosed four types of external casing failures — water-line, casing-casing, collar and body failures. These types are identified largely by their location on the casing. Water-line failures are found just below the surface of water or mud in the casing annulus. Casing-casing failures occur on the oil string just below the shoe of the surface string. Collar failures are found in the threaded ends of casing joints where they are screwed into casing collars. Body failures may occur at any point on the body of a casing joint. Ex- amples of each kind of failure have some of the general characteristics that are shown in Fig. 1. Water-line failures usually result in the circumferential severance of an oil-string casing. The corrosive action causing a water-line failure usually is sharply defined and is limited to a short length of the casing. Casing-casing failures usually are accompanied by pitting corrosion distributed around the oil-string casing for distances up to 100-ft below the shoe of the surface string. Casing-casing failures may also sever the casing. Collar failures seem to start on the first thread at the bottom of recesses between collar and casing joint. Corrosion proceeds across the threads by what appears to be a normal pitting mechanism. Both casing and collar are severely attacked. Body failures are the result of highly localized pitting at any point on a casing wall. Besides the pit that perforates a casing, a large number of other pits usually are found along one side of the casing joint. The pits occasionally are filled with corrosion products consisting largely of oxides and sulfides.' Frequently, the mill scale is largely intact on the rest of the casing. Examination of a casing failure does not always reveal the cause of the failure. Frequently, the necessary details are destroyed when the failure occurs. For example, formation water flowing through a perforation at high velocity may enlarge the hole and destroy any remaining evidence of the cause of the failure. One way to obtain undistorted information about a failure is to study the nature of other pits on the casing in the vicinity of the failure. A study of such pits frequently suggests that they are characteristic of an attack resulting from the differential availability of molecular oxygen.

By M. R. Geer

Coal washing assumed an important role in the mining industry of the Pacific Northwest long before washing practice became firmly established in the Appalachian field. A Scaife washer was operated in the state of Washington in 1887; and by 1927, the fist year for which complete statistics were compiled, nearly a third of the state's coal production was washed, in comparison with only about 5 pct for the country as a whole. Mechanical preparation was adopted in Alaska in 1922 in a plant constructed by the United States Navy at Chickaloon to provide bunker coal for naval forces operating in northern waters. Many of the coal beds mined in Washington and Alaska contained more impurities than those mined elsewhere, and this circumstance contributed to the early interest in mechanical cleaning. A much more important factor, however, was the inclination of the coal beds. With steeply pitching beds, hand sorting by the miner at the face is impossible; consequently, all material must be loaded and dealt with on the surface, just as is now proving the case with mechanical mining of flat beds. Thus "full-seam" mining afforded the same stimulus to the early development of coal washing in the Northwest that - it is providing under mechanization in the rest of the country today.

Jan 1, 1949

By Norman Weiss

IF we were to measure progress this year in terms of large new mills and discoveries of fundamental significance we should certainly be disappointed. Outside of the uranium field there was little of a spectacular nature. San Manuel and Reserve completed their first year of operation; Erie approached readiness; the Toquepala project in southern Peru broke ground and gained speed. Important mill enlargements occurred at Inspiration, Anaconda, Ray, and Climax Molybdenum. A 3000-ton copper concentrator was completed at Pima, near Tucson. The Republic Mill of Marquette Iron Mining Co. started up in April. Abroad, the great developments in the African Copper Belt can be likened to the rapid growth of the porphyry coppers in this country. Fundamental research was confined nearly entirely to iron ore flotation and recovery of metal values from leach solutions, particularly uranium. The large number of review articles this year reflected a desire to take stock and consolidate past gains before taking the next bold steps. Undoubtedly a shortage of competent young engineers and technicians is stunting the natural growth of theoretical investigation in the field of minerals beneficiation, as well as the conversion of ideas into action. We find our small stock of talented young scientists concentrated in a few centers of erudition because there are not enough to diffuse through the industry. It is safe to say that among mine administrators and managers there is more interest in the education, training, and welfare of the young engineer than ever before.

Jan 2, 1957

W. H. Blauvelt, New York, N. Y.—One thought lias been running through my mind during the wholc of this meeting and that is that the scientific and the practical men must recognize very clearly their interdependence. The value of scientific classification of coal is going to be of the very greatest importance to the users, the practical men. Is not the scientific investigation and the great amount of work that is being done in a measure at least lost to the world? Therefore the scientific investigations and the practical needs of the users should bo brought as close together, and the work should be done as closely together, as possible; that is, the scientific man should know what the practical man needs, and the practical man should not feel that the scientific man is merely a theorist. Scientific investigation is going to have a great effeet and be of great valuc to the practical man who is trying to solve his problems. In the subject which I discussed' for instance, we must look to the scientific man to tell us why coal cokes in one way and not In another and why certain coals will do certain things and others, which appear on the surfacc to be generally similar, do not act in the same way. Need or Physical Data on Coal H. J. Rose, Pittsburgh, Pa.—There is a subject which is a sort of hobby of mine; that is, the need for what might be called critical tables of constants for coal. The chemist has big volumes giving constants, such as the density, solubility, specific heat, thermal conductivity and all other physical and chemical data that have been determined for chemical compounds. Data arc also available on many common materials, for example, the density, hardness, modulus of rupture or maximum crushing strength of swamp white oak as compared with some other wood. In fact, physical data for practically cvery hype of wood commercially produced in the world can he found. In the same way the metallurgical man has handbooks giving the properties of alloys, etc., but we havc very little tabulated information about coal. Our principal reference works are the volumes published by the U. S. Bureau of Mines on the proximatc and ultimate analysis and calorific values of coals of the United States. That is 3 pioncer work of enormous value, but we have reached the point where we need more diversified information. Mr. Fulweiler raised the question of the relative strength of the different coals and cokes. Dr. Campbell and Dr. Ashley wanted to have some information on the resistance of coal to air slacking. It was brought out in the discussion that we want to know something about the coking properties of coal. There are any number of physical tests that we need, such as the thermal conductivity of certain coals, the coefficient of expansion, or the coefficient of friction; or other constants. A smattering of such information is scattered through the literature; for instance, a research worker in Wales will report a coefficient of expansion on Wclsh coals and one in South Africa will report something else for one or two kinds of African coals, hut it is difficult to find the information that is needed on our own coals. Would it not be worth while to consider collecting reliable critical

Jan 1, 1930

The Library of the above-named Societies is open from 9 A.M. to 9 P.M. on all week-days, except holidays, from September 1 to June 30, and from 9 A.M. to 6 P.M.. during July and August. The Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information-will receive special attention. The Library is prepared to furnish references and copies of articles on mining and metallurgical subjects; to determine the existence of mining-maps, and to furnish general information as to the geology and mineral resources of all countries: All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape. The members of the Institute. can be of service to the Library by forwarding copies of mining-reports, maps privately issued, and similar material, which will he classified, indexed, and made available to other members. Suggestions for additions to the Library, either by purchase or personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will use the Library freely, and assurance is given that most careful service will be rendered to them.

Jan 5, 1913

By R. I. Jaffee, J. G. Dunleavy, W. Hodge, H. R. Ogden

Jan 1, 1949

By R. M. Goldhoff, J. W. Spretnak, R. Speiser

IT has been observed by Grange and Garvey' that the homogenization of boron-treated steels could lead to complete elimination of the hardenability effect caused by boron. The experimental conditions leading to this conclusion involved the heating of steel specimens with and without boron at 2350°F for 24 hr. To prevent oxidation and decarburization, the specimens were encapsulated under vacuum in silica tubes. This observation of permanent deterioration of boron effect was noted in both a 0.63 pct plain carbon steel and a 0.25 pct C low alloy steel, both of which had been treated with ferroboron and homogenized at 2350°F for 24 hr. In another series of boron-treated steels which had been homogenized for shorter times, the effect was to reduce, but not completely eliminate, the boron effect. Under these circumstances, it was presumed that longer heating times would cause permanent deterioration of the boron effect in this series of steels also. Since the characteristic grain boundary constituent could not be formed in any of these steels after homogenization, it was concluded that possibly boron was being converted into an ineffective form through chemical combination resulting from prolonged heating at high temperatures. Assuming the validity of this observation, a series of experiments to establish the relationship between temperature of homogenization and kinetics of deterioration was contemplated. Initially an attempt was made to reproduce the results just described. For this purpose commercial lots of AISI 8640 and AISI 86B40 steels were used. The analyses of these steels appear in Table I. Hardenability evaluation was on the basis of the hardness of normalized sections. Grange and Garvey' pointed out that these steels are air hardening to some extent and such a technique can be used. For these tests the specimens were held for 20 min in a salt bath at 1600°F and then cooled in still air. Several evacuated silica capsules containing pairs of the test steels were made up and heated for 24 hr at 2350°F. A number of failures occurred among these capsules, but evaluation of the specimens successfully treated indicated a complete deterioration of the boron effect. However, examination of the surface of the treated specimens showed that some reaction, probably with the silica tube, had taken place, since none of the specimens was bright. One further test was made at 2350°F for 12 hr, using a pair of specimens wrapped in tantalum foil prior to encapsulation. These specimens appeared bright after treatment, and their hardenability evaluation showed that no deterioration had taken place. Since these steels are extremely sensitive to de-boronization at high temperatures and particularly at long times of holding, the experimental observations raised some doubt as to the real occurrence of the permanent deterioration effect. To resolve this question an experiment was undertaken in which the high temperature portion of the treatment was completed in vacuum. For this purpose a molybdenum wound resistance furnace capable of maintaining good vacuum was used. All the pertinent accessories to this furnace were machined from molybdenum stock in order to withstand the high temperature involved in the experiment. With this equipment a temperature of 2400 °F was obtained and held under a pressure of 5x10-" mm Hg for 24 hr. A specimen of each of the two test steels was suspended in the furnace and both were heated simultaneously. Temperature was measured with a standardized Pt—Pt-13 pct Rh thermocouple, whose millivoltage at 2400°F was extrapolated from the standardization equation, good up to 2200°F. The complete evaluation of these specimens is shown in Table 11. The hardness values attained by each steel after normalizing, both before and after the prolonged high temperature treatment, remain the same. A microscopic study of the decomposition products present in the microstructures of specimens at various points in the heat treatment correlated with the hardness values observed. It seems that no permanent loss of boron hardenability effect occurs, at least in these Grainal-treated steels, when deboronization is circumvented. Acknowledgments This work was conducted under the sponsorship of the Aeronautical Research Laboratory, Wright Air Development Center, under Contract No. AF 18(600)-94, and their support and permission to publish is gratefully acknowledged. A note of thanks is also extended to the Republic Steel Corp. for supplying the materials used in the work. References ' R. A. Grange and T. M. Garvey: Factors Affecting the Harden-ability of Boron Treated Steels. Tro.ns. ASM, 1946, vol. 37, p. 136.

Jan 1, 1957

By Michael S. Roscoe

In order to more accurately predict longwall surface subsidence over the Pittsburgh No. 8 Coal in Eastern Ohio, North American Coal Corporation's Quarto Mining Company undertook or participated in several subsidence studies. Due to the changing roof geology and rapid variations in the amount of cover two separate areas were investigated at two different mines to determine the subsidence response if any to these changes. Data generated from these studies were compared with NCB derived,data for accuracy and then used to predict subsidence under houses, gas lines and other critical man made structures. The following report summarizes the results of these studies as well as the subsidence case histories of gas lines, transmission towers, houses and water wells. Problems that were encountered during both phases of this process (investigation and subsequent application) are also included.

By L. R. Ingersoll, James Fisher, Harry Vivian

The copper mines of the Keweenaw Peninsula in northern Michigan have long been of interest in connection with deep earth-temperature measurements. The extraordinary low geothermal gradient of l° F. in 223.7 ft. announced by Agassiz1 as a result of measurements dating from 1886, although later2 stated as in error, served to focus attention on this region as one offering, because of the great depth of the mines, unusual opportunity along this line. Lane,3 Van Orstrand4 and others have made valuable contributions to this study. Fresh opportunities afforded by the constant deepening of the mines, improvements in the accuracy and reliability of temperature-measuring instruments together with increasing knowledge of the heat conductivities and specific heats of the rocks, led the Michigan College of Mining and Technology in cooperation with some of the mining companies to renew work on this problem. It is planned eventually to complete a survey which will make use of the favorable opportunities for deep rock-temperature measurements presented in these mines. This survey should include the determination of a depth-temperature gradient in both conglomerate and arnygdaloid mines, and also the variations in temperature at the same depth in different geological formations. The first problem has a direct bearing on the question of providing equipment for necessary ventilation with increased depth. The second may show that a relation exists between the natural rock temperature and the mineral content of the formation. The measurements in all cases are to be guided by heat conduction considerations, to the end that they may represent as closely as possible

Jan 1, 1934

By AIME AIME

PURSUANT to a recommendation made by the Section delegates at their conference at the Annual Meeting of the A.I.M.E. last February, the Directors, at their meeting on March 15, 1944, appointed a committee charged with the duty of investigating the present status of licensing and registration of engineers, and to make a report on the whole subject for the information of the mining fraternity. The committee consisted of E. W. Ellis, chairman, H. D. Keiser, Henry T. Mudd, J. J. Croston, and Simon Strauss. Messrs. Keiser and Strauss were unable to assist in the work of the committee, and Mr. Mudd was forced to resign in July, his place being taken by A. F. Greaves-Walker. Able assistance was given the committee by T. Keith Legare, executive secretary of the National Council of State Boards of Engineering Examiners, and by Ed. ward Larson, executive secretary of the National Society of Professional Engineers. The accompanying somewhat condensed version of the report of Mr. Ellis's committee, dated Oct. 15, 1944, is confined to facts rather than to recommendations. The "Model Law" to which reference is made was first drafted by repre¬sentatives of six national engineering societies in 1911. It has since been amended many times, the latest version dated June 1943 is recommended to the State Licensing Boards as a pattern for formulating or amending state laws. A copy of the "Model Law" in pamphlet form will be sent to any member on request from A.I.M.E. headquarters while the supply lasts. The report:

Jan 1, 1945

By Reginald S. Dean

Manganous oxide is readily soluble in concentrated ammonia solutions containing ammonium salts. Lixiviants of ammonia and ammonium carbamate permit ready extraction of manganese from reduced ores and the manganese in such solutions may be precipitated by heating to transform the carbamate to carbonate. THE widespread occurrence of manganese in low grade oxide and carbonate ores not amenable to mechanical concentration has led to extensive investigations of hydrometallurgical methods for producing a pure manganese compound suitable for further treatment. Manganese carbonate is the preferable compound. This product when fully crystalline and of not too fine crystal size is easily filtrable and stable in air. It can be converted to other compounds such as the oxides by heating in air or can be reacted with acids for producing salts. A useful hydrometallurgical process must produce relatively concentrated solutions that can be purified easily, reagents must be cyclically used, and heat requirements must be small. Neither the ammonium sulphate nor sulphur dioxide leaching processes that have been tested extensively fulfill these requirements. Other heretofore proposed processes have obvious limitations and have not been tried on a large scale. The present process is based on the discovery by the writer of a new group of aqueous manganese-ammonia complex solutions highly concentrated in ammonia, which permit rapid solution of manganous oxide to concentrations of 80 to 100 g Mn per liter and from which a fully crystalline, easily filtrable manganese carbonate is precipitated by the addition of carbon dioxide and partial ammonia removal. Although the process may be carried out with many ammonium salts, commercial advantages dictate the use of ammonium carbamate, which is obtained when CO2 is passed into concentrated aqueous solutions of ammonia. If the carbamate is used, the only reagents, ammonia and CO2, are volatile and may therefore be recovered from solutions and residues by heating, thus eliminating washing and extensive evaporation. Impurities are controlled easily as most metal oxides are either insoluble in the lixiviant or fail to precipitate with the manganese carbonate. Others are controlled by sulphide addition. The process has been tested extensively on a small scale on a wide variety of ores, including Three Kids, Artillery Peak, Cuyuna, and Chamberlain, as repre-

Jan 1, 1953

By Reginald S. Dean

Manganous oxide is readily soluble in concentrated ammonia solutions containing ammonium salts. Lixiviants of ammonia and ammonium carbamate permit ready extraction of manganese from reduced ores and the manganese in such solutions may be precipitated by heating to transform the carbamate to carbonate. THE widespread occurrence of manganese in low grade oxide and carbonate ores not amenable to mechanical concentration has led to extensive investigations of hydrometallurgical methods for producing a pure manganese compound suitable for further treatment. Manganese carbonate is the preferable compound. This product when fully crystalline and of not too fine crystal size is easily filtrable and stable in air. It can be converted to other compounds such as the oxides by heating in air or can be reacted with acids for producing salts. A useful hydrometallurgical process must produce relatively concentrated solutions that can be purified easily, reagents must be cyclically used, and heat requirements must be small. Neither the ammonium sulphate nor sulphur dioxide leaching processes that have been tested extensively fulfill these requirements. Other heretofore proposed processes have obvious limitations and have not been tried on a large scale. The present process is based on the discovery by the writer of a new group of aqueous manganese-ammonia complex solutions highly concentrated in ammonia, which permit rapid solution of manganous oxide to concentrations of 80 to 100 g Mn per liter and from which a fully crystalline, easily filtrable manganese carbonate is precipitated by the addition of carbon dioxide and partial ammonia removal. Although the process may be carried out with many ammonium salts, commercial advantages dictate the use of ammonium carbamate, which is obtained when CO2 is passed into concentrated aqueous solutions of ammonia. If the carbamate is used, the only reagents, ammonia and CO2, are volatile and may therefore be recovered from solutions and residues by heating, thus eliminating washing and extensive evaporation. Impurities are controlled easily as most metal oxides are either insoluble in the lixiviant or fail to precipitate with the manganese carbonate. Others are controlled by sulphide addition. The process has been tested extensively on a small scale on a wide variety of ores, including Three Kids, Artillery Peak, Cuyuna, and Chamberlain, as repre-

Jan 1, 1953

By COURTNEY DE KALB

IRON ore is the cause of the present trouble in Morocco. At least three nations are interested in the outcome and private syndicates have been active. The iron deposits are found in that mountainous northern coast line known as the Rif. This is an uplift that has been cut through, by the northward drainage, representing an ancient land surface. Erosion has produced .a fiordlike coast, which circum- stance has aided contraband' traffic to the tribes dominated by Abd-el-Krim, the chief of the clan of the Beni Urriaguel, near the center of 'the north coast, opposite Alhucemas. The iron deposits are extensive in the territory of the Beni Urriaguel. They were "located," if such a term is permissible, many years ago. The first arrangements, through direct contracts with the tribal chieftains, have been reinforced by compliance with the subsequent code under the Spanish protectorate in 1914. Under those terms, the location had to be made through the Arbitral Commission sitting in Paris. These locations, or "denouncements," were made by the I-louse of Mannesmann, of Hamburg.

Jan 1, 1925

By A. C. Rubel

WHAT does management expect of W and from an engineer? First and foremost, it expects that he should become, and therefore should fit himself in every way to be, a part of management so that he may assume as much and as many of the responsibilities of management as his ability and the opportunities of the job permit. Let me make clear at the start that the profession of pure, technical engineering offers but limited opportunities at the top levels because of the inherent organization of engineering work. The line of succession to top jobs may be likened to a cone with a broad base and an extremely sharp point. Consider any oil company, large or small, or any operating function of that company, and you will find few top engineering jobs in the organization. This is true by the nature of the work handled. There will be a few district engineers depending on the spread of operations, a chief petroleum and production engineer, perhaps a few research engineers, possibly some technical executive assistants, and that is usually all. The road to these jobs is a long one and the competition is tough. The larger the organization the greater the opportunity, but always the ratio of engineers to top engineering jobs is only a small one.

Jan 1, 1947

By Mäkinen, Eero

OUTOKUMPU, a large copper mine in eastern Finland, has the distinction of being one of the few important mines in the world discovered by a geologist the late Otto Triistedt, of the Geological Sur- vey of Finland, having found the out- clop in 1910 by tracing glacial ore boulders, some of which had been carried as far as fifty kilometres. As the mine had no connection with either railways or waterways and the possibilities of transport were poor, the owners first tried the Hybinette hydrometallurgical process to extract the copper. The raw ore was finely crushed, treated by a sulphatizing roast. and then leached. The resulting solution was electrolyzed, using lead anodes. This experimental plant, having a capacity of 10,000 tons (all Ions are metric tons in this paper) of raw ore and producing 300 to LEO0 tons of electrolytic copper annually, was built in 1913 and run until dis-

Jan 1, 1938

By H. R. Wheeler

CREATION of a "committee on promotion of student interest in coal mining" has an encouraging implication for the coal industry. It is indicative that mining men, both in the field and in the educational centers, realize that the problems of the industry require the best talent available. Young men are being invited into coal on the premise that it needs them, that it offers opportunity for creative work and the realization of their objectives. In initiating a movement which purports to meet the objectives of any young man who spends four or five years of his life in college, the industry does so with a full realization of its obligations.

Jan 1, 1940