Search Documents

By Earl S. Greiner, Eric R. Jette

The constitution of the iron-silicon alloys containing from 14 to 33.4 weight per cent silicon has been studied by a number of investigators, whose results have been reviewed in a monograph published by the Engineering Foundation1. In these previous researches, the solubility of silicon in iron was determined by thermal, microscopic or magnetic methods and the compound Fe3Si2 was reported to be stable at temperatures from 0 to approximately 1030' C. This paper describes the results of an X-ray investigation of the solubility of silicon in iron and gives data which prove that the Fe3Si2 phase is unstable below 825" C. In order to obtain the present results on the solubility of silicon in iron, the authors have utilized the lattice constants of the alpha-phase iron-silicon alloys given in a previous publication2, and also some additional data which will subsequently be described. Materials and Methods The alloys used in this investigation are listed in Table 1. They were prepared in 30 or 50-gram ingots by melting specially purified silicon and electrolytic or carbonyl iron in alundum crucibles under a pressure of less than 1 mm. of mercury. The purity of the silicon, electrolytic and carbonyl irons has been given by the authors in previous publications2, 5. The ingots were homogenized in vacuo at approximately 1000" C. for at least 96 hr. and then slowly cooled. The homogenized specimens were ground to powder in a hardened steel mortar. This powder was passed through a 150 or 200-mesh screen and sealed in evacuated quartz, Jena or Pyrex glass tubes and heat-treated as noted in the various tables. Specimens 23A, 24B, 33 and 35 and the specimens heated for one month at 700" C. were quenched by quickly removing the tubes from a horizontal tubular furnace and dropping them into water. The other specimens were quenched by means of a drop-quenching device, which has been described previously3.

Jan 1, 1937

By Charles N. Becker

The practice of drying phosphate in Florida is as old as the industry, which began a little more than half a century ago. The methods, however, have changed considerably. At first, the natural process of exposure to the sun and air was used, later supplemented by wood fires beneath open-air stationary dry kilns and drying towers of various designs. It was not until the early nineties that rotary driers came into use, and at first they were of very small design and fired with wood. As the industry grew and tonnage increased, so likewise grew the number and size of rotary driers, until today the largest installations are 6 ft. up to 7 ft. 6 in. in diameter, and 55 to 60 ft. long, fired with crude oil. The reasons for drying phosphate rock are: (1) to eliminate freight on water in the shipment and (2) to facilitate the good grinding qualities required by the buyers in their acidulation. Phosphate pebbles vary materially in natural characteristics and each property has a direct bearing on the processing. In making comparisons of cost and operating conditions, the following are usually taken into consideration: 1. The hard dense pebbles, which contain very little interior moisture and 6 to 8 per cent total moisture, usually produced from the low-grade deposits. 2. The lighter, porous pebbles, which contain 4 to 5 per cent interior moisture and a total moisture ranging from 9 to 15 per cent. 3. The product of recovery operations using oily reagents, containing from 15 to 25 per cent moisture. 4. The size of the pebbles Usually the plus 5-mesh material is considered as "coarse rock"; the minus 5-mesh plus 24-mesh is "fine rock," and the minute particles below 24 mesh are called "concentrate." 5. The amount of moisture allowed in the dried product. The practice is generally to dry down to 1.5 to 2 per cent moisture. There is, however, an actual range in guarantee of from 1 per cent maximum to 3 per cent maximum.

Jan 1, 1938

By Charles N. Becker

The practice of drying phosphate in Florida is as old as the industry, which began a little more than half a century ago. The methods, however, have changed considerably. At first, the natural process of exposure to the sun and air was used, later supplemented by wood fires beneath open-air stationary dry kilns and drying towers of various designs. It was not until the early nineties that rotary driers came into use, and at first they were of very small design and fired with wood. As the industry grew and tonnage increased, so likewise grew the number and size of rotary driers, until today the largest installations are 6 ft. up to 7 ft. 6 in. in diameter, and 55 to 60 ft. long, fired with crude oil. The reasons for drying phosphate rock are: (1) to eliminate freight on water in the shipment and (2) to facilitate the good grinding qualities required by the buyers in their acidulation. Phosphate pebbles vary materially in natural characteristics and each property has a direct bearing on the processing. In making comparisons of cost and operating conditions, the following are usually taken into consideration: 1. The hard dense pebbles, which contain very little interior moisture and 6 to 8 per cent total moisture, usually produced from the low-grade deposits. 2. The lighter, porous pebbles, which contain 4 to 5 per cent interior moisture and a total moisture ranging from 9 to 15 per cent. 3. The product of recovery operations using oily reagents, containing from 15 to 25 per cent moisture. 4. The size of the pebbles Usually the plus 5-mesh material is considered as "coarse rock"; the minus 5-mesh plus 24-mesh is "fine rock," and the minute particles below 24 mesh are called "concentrate." 5. The amount of moisture allowed in the dried product. The practice is generally to dry down to 1.5 to 2 per cent moisture. There is, however, an actual range in guarantee of from 1 per cent maximum to 3 per cent maximum.

Jan 1, 1938

By Charles Becker

THE practice of drying phosphate in Florida is as old as the industry, which began a little more than half a century ago. The methods, however, have changed considerably. At first, the natural process of exposure to the sun and air was used, later supplemented by wood fires beneath open-air stationary dry kilns and drying towers of various designs. It was not until the early nineties that rotary driers came into use, and at first they were of very small design and fired with wood. As the industry grew and tonnage increased, so likewise grew the number and size of rotary driers, until today the largest installations are 6 ft. up to 7 ft. 6 in. in diameter, and 55 to 60 ft. long, fired with crude oil. The reasons for drying phosphate rock are: (1) to eliminate freight on water in the shipment and (2) to facilitate the good grinding qualities required by the buyers in their acidulation. Phosphate pebbles vary materially in natural characteristics and each property has a direct bearing on the processing. In making comparisons of cost and operating conditions, the following are usually taken into consideration: 1. The hard dense pebbles, which contain very little interior moisture and 6 to 8 per cent total moisture, usually produced from the low-grade deposits. 2. The lighter, porous pebbles, which contain 4 to 5 per cent interior moisture and a total moisture ranging from 9 to 15 per cent. 3. The product of recovery operations using oily reagents, containing from 15 to 25 per cent moisture. 4. The size of the pebbles. Usually the plus 5-mesh material is considered as "coarse rock"; the minus 5-mesh plus 24-mesh is "fine rock," and the minute particles below 24 mesh are called "concentrate." 5. The amount of moisture allowed in the dried product. The practice is generally to dry down to 1.5 to 2 per cent moisture. There is, however, an actual range in guarantee of from 1 per cent maximum to 3 per cent maximum.

Jan 1, 1936

By T. L. Joseph

THE invention of the Bessemer converter process in 1856 added great impetus to the manufacture of steel and is one of the outstanding contributions to process metallurgy. Although the process of refining pig iron by passing air through the molten metal bears the name of Henry Bessemer, it should be mentioned in passing that William Kelley of Eddysville, Ky., worked on the process as early as 1847. Kelley was granted a patent on the process in 1857, inasmuch as he was able to prove priority in discovery.1 After considerable litigation in 1865 the respective interests of Kelley and Bessemer were combined. On Sept. 10, 1856, Robert Mushet of England obtained his first patent on the application of manganese to cast steel. Mushet anticipated trouble in purifying iron by passing currents of air through it. His patent specified that steel made in this way often contained flaws and was red short or cold short. Mushet understood the refining of pig iron into steel well enough to realize the difficulties likely to be encountered from oxidation of the iron. Mushet was not only an inventor but he was also an investigator. He understood the principle of selective oxidation which takes place in the converter process, arid he realized therefore that the remedy for over-oxidation was attainable if a suitable metal could be found at a reasonable cost and in sufficient quantities. His first experiments were made in small crucibles holding a few ounces of metal. Later his work was conducted on a larger scale and with complete success. Manganese had been used in making steel a quarter of a century before the converter

Jan 5, 1927

By D. Harker, E. Epremian

The constitution of the nickel-tungsten system has been studied by a number of investigators, the most recent of which are Ellinger and Sykes.1 On the basis of metallography, electrical resistivity and hardness measurements and some X ray diffraction work, they constructed a consitution diagram (Fig 1). Ellinger and Sykes report a0 for the alpha face-centered cubic phase (nickel saturated with tungsten) as 3.66?.‡ The gamma phase (tungsten saturated with nickel) is given as body-centered cubic, but no value of a. is recorded. At 43 pct tungsten by weight (approximately 20 at. pct) a beta phase is reported, but structure and lattice parameter are not known. Primarily on the basis of metallographic evidence, they conclude that beta is a new phase and rule out the possibility of formation of a superlattice since they- observe a new phase in the microstructure. Grube and Schlecht2 report an ordering reaction in a system similar to the Ni-W (Ni-Mo) and Harker3 has shown that NirMo forms a superlattice upon the pre-existing face-centered cubic lattice of the alpha phase. Elliniger arid Sykes observed a change in the diffraction pattern of a 4.3 pct W alloy upon aging and attributed it to the formation of a new phase. Thus, there appears to be some question as to the character of the beta phase reported by Ellinger and Sykes. The purpose of the present work is to determine precisely the structure and nature of the beta phase in the Ni-w system of X ray diffraction methods. Experimental Procedure One inch diameter ingots of 43.66 pct, 40.15 pct and 34.06 pct .tungsten by weight (19.8, 17.6 and 14.1 at. pct respectively) were melted and cast under vacuum from electrolytic nickel and pure wire filament grade tungsten. The ingots were soaked for 16 hr at 1300°C in a hydrogen atmosphere furnace, then swaged at this temperature and finally drawn to 0.020 in. diam wire. Some of the bar stock was retained in 1/2 in. diam rod for hardness and metallographic studies. Wire samples for diffraction work were sealed in evacuated quartz tubes and subjected to the various solution and aging heat treatments in a hydrogen furnace. X ray photograms were taken in a Debeye-Slierrer camera using copper K radiation filtered by nickel foil. Results X RAY DIFFRACTION The lattice parameters of the alpha and gamma phases at saturation were determined by an X ray photogram of the 19.8 at. pct W alloy after solution heat treatment at a temperature well within the alpha-gamma range above the peritectoid temperature (17 hr at 1150°C—oil quenched). The alpha phase was found to be face-centeted cubic with a. of 3.594 ± 0.001?, while the gamma phase was determined as body-centered cubic with a. of 3.158 ± 0.001?. Exactly the same phases and parameters were ohtained with the 17.6 at. pct W alloy for the same solution heat treatment. Thorough analysis was made of an X ray photogram of a 19.8 at. pct alloy sample in the quenched and aged condition (solution treated 1T hr at

Jan 1, 1950

By Robert W. Edwards

The Morris mine, operated by the Inland Steel Co., is located about 5 miles west of Ishpeming, Mich., near the west end of the Marquette Range. The ore, a soft hematite, is mined by sublevel caving and stoping. A considerable amount of surface water flows down through the cave into the ore or percolates down along footwall dikes in the iron formation. Because of this water, the broken ore cannot be stored in the raises and must be scraped from the sub directly into the tram cars. Efficient tramming, therefore, requires close coordination between the scraping and loading operations. In the past this has been hampered by the lack of a suitable means of communication between the mining contracts and the drawpoints on the tramming levels. Among the devices that have been tried unsuccessfully are flashing lights, air whistles, and electric buzzers.

Nov 1, 1955

By William P. Mason

FoR reasons unnecessary to enter into here, I was called upon to contradict the statement that " closed metallic vessels, partly filled with water and heated, do not become shattered by violent explosion, but simply rupture by over-pressure;" and the following experimental results were obtained in support of my position : A piece of drawn brass tubing (telescope-tubing) 1 1/2 inches in diameter and 15 inches long was closed at both ends by screwing on heavy caps of bronze. Before closing the second end the vessel was half filled with river water, the cap was then screwed on, and the closed vessel was supported upon two iron anvils, and heated in the interval between the supports by a large Bunsen lamp. The resulting explosion (which was doe to over-pressure only and not to any more occult cause) was exceedingly violent. No small damage was done to the room in which the experiment was undertaken; and the noise was like that of a cannon. Those of the pieces which could be recovered are shown in Fig. 1. Upon examining the wreck, it was noticed that one of the heavy bronze end-caps had preserved its circular section and still contained that portion of the barrel of the tube which had been screwed into it, while the other end-cap contained no portion of the tube, and was moreover sprung into a shape more or less elliptical, as if from excessive lateral strain. It was also observed that the large pieces of the shattered boiler predominated towards the end which had been closed by the un-sprung end-cap. The reasonable explanation, in view of the facts, was, that over-pressure had caused the boiler to yield through the screw-threads at A B, Fig. 2, and the righthand end-cap had blown off, thus leaving the boiler half filled with water, greatly super-heated for the new (atmospheric) pressure to which it was suddenly reduced; that this water had consequently sprung instantly into steam with dynamite effect, shattering the tube and springing the remaining end-cap. The large pieces would be expected at the open end of the boiler, as at that point the "tamping "would have been that of the atmosphere only. This explanation assumes a rupture to have been caused by gradually increased pres-

Jan 1, 1893

By J. N. Ong, J. P. Ratledge, J. H. Boyce

SINCE German operators opened the Tsumeb mine in the early 1900's, continuous operation has been interrupted only by enforced shutdowns during two world wars and the depression of the 1930's. Original metallurgical practice was blast furnace smelting. This was applicable only to low zinc ore, leaving large tonnages of high zinc ore to be stockpiled on the surface. A gravity concentrator using tables, buddles, and jigs operated for several years, but differential flotation of the ore did not get beyond the experimental stage. When the property was put up for sale by the South African Custodian of Enemy Property there was an estimated 434,000 tons of ore on surface dumps. The dump material, assaying 4.48 pct Cu, 15.8 pct Pb, and 10.9 pct Zn, had become highly oxidized during a stay of many years on the surface. But these dump ores had to be used in evaluating possible metallurgy because the shaft became flooded after the 1940 shutdown and underground ore was unavailable. Many companies examined Tsumeb but quickly lost enthusiasm because of the formidable metallurgical problems presented by the dump ore. However, on the basis of extensive test work, the present company decided that differential flotation would be successful and purchased the property after competitive bidding. Geology and Mineral Association is Complex The Tsumeb mine lies near the northern boundary of South West Africa at an altitude of 4200 ft. The village of Tsumeb is 335 air miles northeast of Wal-vis Bay, territorial port of entry. The orebody is a hydrothermal replacement deposit associated with an irregular intrusion of aplite cutting folded pre-Cambrian dolomite beds. In plan the deposit is a lens of 250x600 ft maximum dimensions. In section the orebody dips 55" south from the surface to 2000 ft, below which there is a reversal in dip to 75" north. Mineralization is localized in the aplite and in the adjoining brecciated dolomite. In the upper levels the ore is largely confined to a single lens, but below the 1890 level massive sulphide ore forms north and south lenses that partially enclose a pipelike body of medium to low grade disseminated ore, part of which is of too poor a grade to mine. Drilling below the 24th, or bottom level, has disclosed that a high percentage of the mineralization from the 3000 to 3300-ft horizons is comprised of copper and lead oxides. The deep oxidation may be local, since it appears due to circulating waters in a major fault cutting the orebody. Tsumeb ranks as one of the highest grade base metal deposits in the world. It is geologically and mineralogically famous for 41 copper, lead, zinc, vanadium, and germanium ore minerals, but its complex mineral assemblage is not attractive to metallurgists. In addition, there is a gradual change in oxidation intensity from the upper levels to the lowest level now operating, which is the 24th. This is well illustrated by the copper minerals. In the upper levels malachite and azurite are predominant, in the intermediate levels chalcocite, and in the lower levels tennantite. Throughout the mine there are sufficient heavy metal soluble salts to activate zinc, and large amounts of depressants are required even for so-called clean sulphide ores. When the same sulphide ore is exposed to prolonged oxidation aboveground, as was the case with the dump ores, reagent requirements become fantastic. Plant Construction First staff members arrived at Tsumeb in March 1947, and by May essential services had been restored and mine unwatering began. In 2 1/2 months company employees built a temporary jig and sorting plant for treating existing dumps to provide a saleable product during high metal prices. Meanwhile, concentrator design and construction was contracted to a South African firm, with subcon-

Jan 1, 1956

By E. J. Fasiska, H. Wagenblast

The dilalion of a ivon by interslilial carbon was measured by two independent techniques —dilatometric mesurements at 719 c and X-ray measurments of the urlil cell parameters a1 room temperature after quenching. The relative expansion per increase in cavbon content by both methods is (2.9 + 0.3) x 10-3 pev at. pcl C nrzd is temperature- independent within experimental error. This corresponds to (6.3 5 0.6) cu cm per g-atom for the partial gram-atomic volume of carbon in a iron-only slightly smaller than the atomic volume for iron in the same temperature vange. THE only previous quantitative study of the dilational effect of carbon dissolved in a iron was performed in 1934 by Burns1 which, at the time, generated some discussion of possible sources of experimental error.2 For a system of such widespread importance, we felt that a new investigation was merited. Both X-ray diffraction and dilation measurements were used to determine the expansion of the a iron lattice by dissolved carbon, avoiding as much as possible any previous experimental problems and deficiencies. The dilation method at solution temperature offers not only measurements which are free of residual strain but also, in conjunction with the room-temperature X-ray measurements, a method to detect any large temperature dependence of the partial gram-atomic volume of carbon. To insure that quenching strains did not affect the room-temperature X-ray measurements, wire specimens of constant carbon content but different diameter were examined for such an effect. SPECIMEN PREPARATION The material used for both experimental techniques was "Ferrovac E" iron received in the form of 19-mm-diam rod and stated as having the following impurity contents: C, Cr, Cu, Mn, P, and V, each in the range of 10 to 50 ppm; Co, O, Mo, S, and Si, 60 to 100 ppm; W, 200 ppm; Ni, 230 ppm; N, 4 ppm. The stock material was cold-swaged to 0.71 mm diam for the Debye-Scherrer X-ray camera specimens and portions were cold-rolled from 6.3 mm diam to 0.79- and 0.25-mm sheet for X-ray diffractometer and dilation measurements. The wires were annealed in wet hydrogen for 6 hr at 840°C and 15 hr at 720°C, and then quenched into 0°C water. A chemical analysis for carbon after this treatment gave 0.0046 + 0.0014 at. pct C. Three portions of these wires were subsequently held at 719°C in three different hydrogen + methane mixtures and then quenched, resulting in carbon concentrations of 0.0283, 0.0598, and 0.1067 at. pct C by chemical analysis. After carburizing, the wires were swaged to 0.48 mm and electroplated with silver to prevent carbon loss during subsequent heat treatment. The final heat treatment consisted of holding the wires at 72 1°C for 5 min in a He-2 pct H mixture followed by quenching into 0°C brine. The wires were held at room temperature for a few minutes to remove the silver plating using a phosphoric acid-hydrogen peroxide solution, and then stored in liquid nitrogen until the measurements were made. EXPERIMENTAL TECHNIQUE A) Dilation Measurement. The dilatometer consisted of a gas-atmosphere vertical tube furnace modified so that length changes of a ribbon-shaped specimen could be measured externally. This was done by installing a gas-tight mercury seal at the top of the furnace as shown schematically in Fig. 1. The specimen (21.0 cm long, 1.27 cm wide, and 0.25 mm thick) was suspended in the center of the furnace by 3-mm-diam quartz rods with the upper one passing through the cap of the mercury seal. Above the cap, the upper quartz rod was coupled to a lever exerting a load of about 25 g (-12 lb per sq in.) on the specimen and having a 10 times mechanical magnification. The vertical position of a marker at the other end of the beam was read with a traveling microscope with a precision of 0.01 mm. The temperature gradient of the furnace was meas-

Jan 1, 1968

By W. N. Logan

WHAT is mineral wool? This question is frequently asked by those unacquainted with its manufacture. The word "mineral" suggests that it is of mineral origin; the word "wool" suggests that it is of animal origin; but the only similarities it has to wool are its fibrous character and its white fleecyness. Mineral wool is a fiber produced by melting rock to a glasslike condition and blowing the glass into fine white, wool-like threads. A -number of the products fabricated from-mineral wool are used for some form of insulation, but mineral wool is adaptable to many other uses. It is used in the manufacture-of pipe covering designed to with; stand the high temperatures produced in steam pipes. In a similar form of insulation it is used to cover boilers and furnaces. It is used in ,the fabrication of upholstery tow for sofas and car seats: In acoustics it has many uses, such as acoustifibroblock, which is used in floors to destroy sound and vibration, and acoustic mat, which is used under carpets to destroy sound. In the insulation of houses, loose wool and granulated wool are used beneath attic floors and between the studding in frame buildings to prevent the escape of heat in winter and the entrance of heat in summer. Mineral wool is used also in fabrication of linofelt, which is a quilted form of insulation; in fibrofelt, which is an insulating board; in the fabrication of lith, which is an insulating block; in anti-fibroblock ,which is used in insulation and refrigeration; in flexfelt; in loose wool; in pressed block; in heavy oiled wool; in dark oiled block; and for many other purposes. The materials used in the manufacture of mineral wool are of two kinds. The first is a rock which contains silt, clay and silica, with smaller amounts of lime and magnesia. The second is a more highly calcareous rock which may carry a small amount of magnesia. The latter is used as flux to assist in the melting of the former. The relative proportion of the alumina-iron-silica content to the lime-magnesia content is normally as fifty to fifty but a considerable range is possible.

Jan 1, 1932

By S. S. Marsden, S. A. Khan

Externally generated foam was injected continuously into short porous media. Both flow rate and pressure drop were measured. Liquid saturation was determined by electrical conductivity. Foam yuality I, expressed as the ratio of gas volume to total volume, was varied from 0.70 to 0.96. As measured with a modified fann VG Meter, apparent viscosity of this foam µa decreases with increasing shear rate but usually falls within the range of 50 to 500 cp. At a given shear rate, µa increases almost linearly with I-. When measured with a Bendix Ultraviscoson, kinematic pa is independent of V but absolute pa increases with T from about 3 to 8 cp. The effective permeability -apparent viscosity ratio ke/µa decreases almost linearly with V for porous media of high permeability, but the rate of decrease becomes less for tighter ones. The relative permeability-apparent viscosity ratio kr/µa us V data does not fall on a single line. The kr/µa ratio increases with liquid saturation in the porous medium and with surfactant concentration. Estimates of pa for foam in porous media vary from 30 to 100 cp. INTRODUCTION Although research on the development of a foam-drive, oil recovery process has been going on for almost a decade, most of the significant publications have appeared within the last several years. This illustrates well the rate at which interest in this process is accelerating. Bond and Holbrook 1 were the first to describe the use of foam to improve oil recovery in their patent of 1958. They proposed that an aqueous foaming agent slug be injected into the formation and that this be followed by gas to produce a foam in situ. Fried 2 studied the injection of foam into porous media which had already been subjected to conventional gas or water drives and found that gas could be used to drive a foam bank which would, in turn, displace additional oil in the form of an oil bank. He attributed the increased oil recovery to the high effective viscosity of foam flowing in porous media. His microscopic observations showed the importance of foam generation and regeneration within the porous medium. By injecting both air and aqueous surfactant solution, Bernard3 generated foams within the porous medium in which oil displacement was being studied. In a separate empirical test, he also measured the dynamic foaming characteristics of the same surfactants in water and/or oil. With some exceptions and for the seyen surfactants studied, there seems to be a qualitative relationship between the efficiency of liquid rlisplacrment and the dynamic foaming testtsed. This relationship was not consistent enough to eliminate the necessity of actual foam flood tests in porous media for surfactant selection. In a study basic to gas storage in aquifers, Bennett4 described the displacement of brine by foam in consolidated porous media. Among other things, he stated that the ability of a surfactant solution to foam is more important than the stability of its foam. The presence of a foam bank between the displacing air and the displaced brine improved both breakthrough and ultimate recovery. In a continuation of this work Kolb5 attributed the great reduction in surfactant solution production rate as displacement by air progressed to a decrease in relative permeability to gas. These several effects reported by both Bennett and Kolb can all be attributed to the high apparent viscosity of foam which was obviously flowing in the porous media. Bernard and Holm6 observed that gas permeability in the presence of foam was much less than in the absence of foam when both were measured at the same gas saturations. This reduction in permeability was proportionately greater for more permeable sands and sandstones than for the less permeable. Viscosities of the surfactant solution and air were used for their calculations rather than apparent foam viscosities. The foam stability increased with decreasing permeability, which was probably due to the natural regenerative properties of porous media, and the permeability reduction increased

Jan 1, 1967

By C. E. MacQuigg

BY and large the education of the engineer has been conservative and the reasons for this are obvious. Quite properly it has been a tradition of engineering education that facts and not fancies must be adhered to. Without a doubt, those men who formed the mold of our engineering philosophy as much as it is possible for such molds to be established-rightly held the highest standards of intellectual honesty. Fortunately, it was unthinkable to them to temporize with untried theories and naturally the men whom they trained as engineering educators carry this philosophy in turn to their students, thus handing down the tradition of stability.

Jan 1, 1943

By Michael Hoch, Seong Kwan Rhee

The ternary system Zr-Cr-0 was investigated at 1200°, 1500°, and 1700°C. The isotherms at these temperatures were determined by metallographic and X-ray diffraction analysis of carefully selected alloys. AS a part of a series of investigations1-4 of the ternary and quaternary phase diagrams on refractory metals and their compounds, the ternary system Zr-Cr-O was investigated at 1200°, 1500°, and 1'700°C. The binary diagrams Zr-Cr, Zr-O, and Cr-0 as reported by Hansen5 and Levin et a1.' and the existence of a ternary coompound ZrsCrsO (q-carbide structure a. = 11.96A) provided a good base for this investigation of the Zr-Cr-O phase diagram. MATERIALS The materials used and their suppliers were: Zirconium powder, 99.4 pct pure, Charles Hardy, New York; Zirconium dioxide, Fairmount Chemical Co., Newark, N.J.; Chromium powder, 99.85 pct pure, Fairmount Chemical Co., Newark, N.J.; Chromium sesquioxide, 99.86 pct pure, J. T. Baker Chemical Co., Pillipsburg, N.J. Though the materials used were not "hyperpure", the impurities present do not affect the results (lattice parameters, phase boundaries) within the experimental accuracy. EQUIPMENT AND PROCEDURE The detailed procedures and equipment used for this investigation were similar to those described elsewherel' "ith the exception that in this study an induction-heated argon-atmosphere furnace was used. The latter furnace was used to prevent the vaporization of chromium metal in samples in the higher temperature range (above 1200°C). The tungsten crucible was induct ion-heated in a vertical quartz tube filled with argon gas. The quartz tube was 1-1/2 in. in diameter and 10 in. long; it was connected at the top and bottom to water-cooled copper plates. The argon gas of a purity 99.995 pct was further purified by being passed through zirconium metal chips which were maintained at 800°C in a silica tube 1 in. in diameter and 30 in. in length. The furnace was flushed with argon gas for an hour before starting heating; during heating, a slight (3 cm oil) overpressure of argon was maintained in the system. Power was supplied by a 20-kw Ther-Monic Induction Generator. The samples rested on a tungsten-wire basket; the wire basket was connected to a tungsten wire which passed through the tungsten crucible lid, and entered the system on top through a Wilson-type seal. By pulling on the wire, the sample was removed from the crucible and dropped to the water-cooled copper base of the furnace. Because of the presence of argon gas, the cooling of the sample was even more rapid than in the vacuum furnace.' EXPERIMENTAL RESULTS AND DISCUSSION 1) Isothermal Section at 1200°C. The compositions investigated have been numbered within the phase diagram, Fig. 1, and all the pertinent information about the samples can be found in Table I. This table lists the composition of the samples, the phases present in the room-temperature diffraction patterns, the phases detectable in the microstruc-ture, and calculated lattice parameters of the a-zirconium phase. The shapes of the various phase

Jan 1, 1964

By R. W. Brauchli

During the last few years the compila-tion of formation logs from rotary well cuttings has become common practice among petroleum geologists. This meth-od has undoubtedly furnished a great amount of information valuable for both scientific and commercial purposes. How-ever, in spite of its great usefulness it has certain drawbacks, principally in the contamination of cuttings by cavings. In extreme cases this contamination can reach such proportions that it is next to impossible to draw conclusions with any degree of certainty as to the nature of the formations penetrated by the drill. This difficulty was frequently encoun-tered during the development of the Okla-homa City Field. In many cases where Wilcox sand-the most prolific sand of this field-was drilled, the samples con-sisted almost entirely of shale cavings with only traces of sand. In order to obtain more reliable knowl-edge of the formations encountered while drilling it is therefore necessary to resort to more coring, and above all to improve our present methods of coring. With this in mind a study has been made of the results of coring in the Oklahoma City Field, and the present article is mainly confined to a statistical analysis of the relation between recovery, diameter of cores and drill pipe, length of cores and a few other factors. Most of the coring in the Oklahoma City Field was done during the early part of, the development. A total of around 18,000 feet or 0.3 per cent of the total footage drilled before February, 1932, has been cored, and about 80 per bent of the cores were taken in the Simpson formation at a depth below 6,000 feet.

Jan 1, 1933

"The richest hill on earth" had its start as a placer gold camp in 1864. The gold was quickly worked out but then silver was discovered in the copper ores in Butte Hill. After ten years as a silver camp, rich copper ore was found in 1881 and the future of Butte was assured. In the early 1960's, the Anaconda Company began the shift from underground mining at Butte to open pit mining of the enormous, low-grade copper deposit surrounding the old high-grade veins which had been worked for over eighty years. Their first primary crusher was a 66 in. by 84 in. (168 m by 2. 13 m) jaw crusher. The pit was expanded at such a rate, however, that its location became endangered. Additionally, the new Clyde Weed concentrator had been built at Butte; and in 1969 construction of a new gyratory installation was started. The primary crusher at the Clyde Weed concentrator is one of the most unusual primary crushers ever put into operation. At times, the ore from the Berkeley pit contains large amounts of timber, pipe, rails, and so forth left in the ore body from the old underground mining operations; and the crusher installation had to be designed so this tramp material could be readily removed ahead of the crusher. Ore is delivered by 100- and 150-ton trucks to two side-by-side dump pockets, each with a capacity of 400 tons. Originally, a hydraulic grapple was installed on the dividing wall between the dump pockets; but it was found that oversize boulders large enough to block the discharge opening at the bottom of each hopper were rapidly covered with other material, and the grapple was unable to reach and remove the large boulders causing the blockage. In addition, the grapple was located in a quite vulnerable position; and it sustained damage from being struck by rock dumped from the trucks. Oversize boulders are now blasted. Underneath each pocket is a vibrating grizzly feeder with the grizzly bars set at 4 in. (102 mm). These feeder-grizzlies are 84 in. (2. 13 m) wide and 32 .ft (9. 75 m) long, with grizzly sections 16 ft (4. 88 m) long. Approximately 75% of the ore passes through the grizzlies and grizzly oversize then drops onto two parallel 6 ft (1. 83 m) wide picking belts. The belts are 3 in. (76 mm) thick and rest on idlers supported by air- filled rubber shock absorbers. At the side of each picking belt is a hydraulic grapple which is used to remove timbers too large to be removed by hand. At times, four men are used to remove timber and tramp iron. Timbers are dropped onto a transverse belt conveyor which discharges into a truck stationed outside the primary crusher building,

Jan 1, 1978

By R. F. Rolsten

The preparation of pure metals by the thermal decomposition of volatile halides was developed byde boer' and van Arkel.2 This has proved to be a useful technique for the refining of columbium,the mechanical and physical properties of which are seriously altered by such interstitial contaminants as oxygen, nitrogen, hydrogen, and carbon. The conventional deposition surface of a resis-tively heated metal filament was replaced, Fig. I, with an indirectly heated clear quartz surface. The impure columbium (feed) was contained in the annular space between the Vycor deposition bulb and the perforated molybdenum retaining cylinder. The head assembly was attached to the deposition bulb by fusing the Vycor at "A". This unit was then connected to a vacuum system composed of a three-turn glass coil to eliminate fracture due to vibration or expansion, a McLeod gage, a cold trap, a two-stage mercury diffusion pump, and a mechanical pump. The entire system was cold outgassed, and the 10 to 20 g of iodine in the auxiliary bulb (reservoir) was held in dry ice to prevent excessive loss of iodine. The columbium was hot outgassed at 800" to 825oC with the pressure maintained at l0-5 to 10-6 mm Hg for 48 hr and cooled under vacuum to 200° to 240oC. Iodine was sublimed from the reservoir and collected in the deposition bulb. The feed material temperature was adjusted to give the desired iodide vapor pressure and the finger temperature of 1000" C was independently attained and measured with a platinum-platinum 10 pct Rh thermocouple located in the center of the nichrome wire helical heating element, "F." The system was attended until temperature equilibrium was established, whence it operated without attention. This is a definite ad- vantage over the conventional "hot-wire" technique which required either constant attention or automatic control. In operation, the iodine vapor originally introduced into the vessel reacted with the crude metal to form a columbium iodide. This iodide vapor diffused to the hot deposition surface where it thermally decomposed, depositing columbium and releasing iodine. This liberated iodine then diffused back to the crude columbium where iodide was formed again. Thus, by repetition of this process, the iodine carried pure columbium from the crude material to the filament, where it deposited. The success of the "iodide" process in producing ductile metals depends on preventing the transfer of oxygen, nitrogen, hydrogen, and carbon from the feed material to the deposit. In many cases relatively minor quantities of these interstitial contaminants impair the ductility of metals. The material produced by the iodide process has such exceptional ductility that it is frequently and mistakenly assumed that iodide metal is always of very high purity. This assumption is not necessarily true since a number of metallic impurities can also be transferred. In the present investigation, the temperature of the feed material was adjusted to iodinate selectively and the deposition temperature adjusted to decompose the iodides selectively. By this technique, some metals present in the feed material were prevented from codepositing with the columbium. It is quite important to have the feed material symmetrically located around the deposition surface in order to obtain a uniform deposit at the maximum rate. For example, Runnalls and pidgeon3 observed that, when the base of a titanium filament was about 1 cm from the feed material, deposition was rapid on that section close to the feed, but that the rate decreased with distance from the feed so that a

Jan 1, 1960

By E. C. Patton

Jan 1, 1947

By E. C. Patton

Jan 1, 1947

By C. E. Wood, E. P. Barrett, T. L. Joseph

The invention of the Bessemer converter process in 1856 added great impetus to the manufacture of steel and is one of the outstanding contributions to process metallurgy. Although the process of refining pig iron by passing air through the molten metal bears the name of Henry Bessemer, it should be mentioned in passing that William Kelley of Eddysville, Ky., worked on the process as early as 1847. Kelley was granted a patent on the process in 1857, inasmuch as he was able to prove priority in discovery.' After considerable litigation in 1865 the respective interests of Kelley and Bessemer were combined. On Sept. 10, 1856, Robert Mushet of England obtained his first patent on the application of manganese to cast steel. Mushet anticipated trouble in purifying iron by passing currents of air through it: His patent specified that steel made in this way often contained flaws and was red short or cold short. Mushet understood the refining of pig iron into steel well enough to realize the difficulties likely to be cncountered from oxidation of the iron. Mushet was not only an inventor; he was also an investigator. He understood the principle of selective oxidation which takes place in the converter process, and he realized therefore that the remedy for over-oxidation was attainable if a suitable metal could be found at a reasonable cost and in sufficient quantities. His first experiments were made in small crucibles holding a few ounces of metal. Later his work was conducted on a larger scale and with complete success. Manganese had been used in making steel a quarter of a century before the converter

Jan 1, 1927