Search Documents

By AIME AIME

THE report of the united. States Steel Corporation for the' year 1928 gives the, following ,figures of raw materials and' finished products . Raw materials, tons :

Jan 1, 1929

By K. M. Kolobova, E. Z. Kurmayev, A. Z. Menshikov, S. A. Nemnonov, V. A. Trapeznikov

The present work represents a review of our intestigations into the X-ray spectra of solids, which have been carried out by us along two lines of upproach: 1) St@ of the electronic structure of high -rnelting compounds of transition metals; 2) stzddy of the interatomic binding forces by the fine structure of absorption spectra under varying temperature and concentration conditions. With this in mind, int>estigations hare been made into the emission and absorption spectra of the K-series of atoms of transition elements in alloys and compounds. In the problem concerned with the electronic structure of high-melting compounds of transition metals, considerable importance is attached to the question of ascertaining the role played by 3d4sp electrons of metal and 2p electrons of metalloid in the formation of chemical bonds and of giving, on the strength of this data, an explanation of the properties which seem to be contradictory at first sight: good conductivity inherent in metals and high brittleness and high-melting characteristics typical of covalent compounds. Over the last few decades this question has attracted the attention of many investigators whose studies were devoted to this type of compound. Many works, both of theoretical1-3 and experimental4- l5 nature , have contributed much to the elucidation of the physical character of the phenomenon referred to. Alongside the investigations in the field of electric resistance, Hall effect, paramagnetic susceptibility, electronic heat capacity, and the temperature of transformation into a superconducting state, we should particularly emphasize the studies on X-ray spectra, which have played a significant role in the development of the zonal theory for high-melting compounds. This fact has become highly evident after the theoretical calculation of the energy spectrum has been made and the density of states curve in Tic, TiN, and Ti0 has been plotted by Ern and Switendick3 who used the method of augmented plane waves. Correlation of the results of the theoretical calculation of the band structure in the compounds listed above with the data obtained by X-ray spectroscopy studies showed that X-ray spectra can be a source of valuable information on the electronic structure of high-melting compounds within a wide range of ener- gies. It is well known that X-ray emission spectra basically give a direct picture of the occupied excited states above the Fermi level of a solid (valence band, conduction band) and that the absorption spectra (region of initial absorption) give a similar picture of states corresponding to the unoccupied levels near the Fermi surface. Full information on the density distribution of electronic states by energies can be obtained by combining the emission and absorption spectra. Such an opportunity arises from investigation

Jan 1, 1970

The figures given here were received through the courtesy of the Bataafsche Petroleum Maatschappij and the Standard-Vacuum. There is an increase in production for the year of approximately 4½ million barrels. In November the average production indicated that during the year 1935 the total production would probably exceed 50 rnillion barrels. To maintain this production, only 106 wells were drilled during the year, mainly in South Sumatra.

Jan 1, 1935

By S. F. Shaw

IT IS generally recognized that the natural gas absorbed in petroleum plays the leading r6le in moving the oil through the sands to the well and supplies the energy that delivers the oil to the surface when the wells are flowing. It is the purpose of this paper to note the amount of oil that could be lifted by this gas if 100 per cent. efficiency were obtained and the efficiencies actually obtained in the use of this gas. An article in MINING AND METALLURGY,' stated that in a Wyoming field, with a pressure of 300 lb. per sq. in., there would be absorbed 65 cu. ft. of gas per barrel, or 1.55 cu. ft. per gal. of oil. The writer does not know if data have been obtained, by experiment, for pressures beyond those indicated in this article, therefore, for the purpose of illustration, he has projected this curve to obtain figures for pressures greater than 300 lb., although probably experiment will show that the extended line is not quite correct.

Jan 1, 1926

By C. H. Mahoney, A. L. Tarr, P. E. Le Grand

Magnesium, it is now generally realized, differs in some important aspects from most other structural metals, not excepting even its close neighbors, the aluminum-base alloys. This is particularly true with respect to the effects of elevated temperatures on the two light metals when in the molten state. Aluminum, 0' the one hand, should not be raised above its melting point any higher than is absolutely necessary if one is to avoid danger of gas absorption and a tendency toward grain growth in the resultant casting.' Magnesium alloys, in sharp contrast, actually benefit by being heated to temperatures considerably above their melting point, It is a commonly accepted practice to establish the desired fine grain in the industrial magnesium alloys of the aluminum-hearing group by raising the temperature of the melt after the refining treatment to some 250°C (482°F.) above the melting range. To recall briefly the typical practice for magnesium alloys, the molten metal is refined by fluxing at about 730°C. (I350°F.), and after the melt has been covered with a suitable flux, the temperature is raised to between 870°C. (I600°F.) and 930°C. (1700°F.). It is then cooled as quickly as possible to the casting temperature. This superheating, as it is called, results in a fine-grained cast metal structure which has superior mechanical properties, enhanced amenability to 'solution heat-treatment, and better machinability than cast metal that has not been superheated. The minimum temperature of superheating varies to some extent with the composition of the alloys to be treated and usually increases with the percentage of magnesium in alloys containing the same constituent metals.' It should be noted that the grain-refining effect of superheating is markedly apparent only in connection with the alloys containing aluminum as an alloying Constituent—the binary alloy containing 1.5 per cent manganese, for example, is not refined in grain to any noticeable extent by a superheating effort. While the phenomenon of superheating is well known in the magnesium industry, the mechanism of the process has remained a mystery During the superheating cycle something occurs that forces a fine grain upon the solidifying metal. The process has been controlled in an empirical manner, and occasionally, especially on large-scale melts, and for no apparent cause, no grain refinement is obtained from a superheating treatment. Only a few papers of importance have been published on the subject. Of these, one of the most helpful is the paper by Achenbach, Nipper and Piwowarski,3 which gives considerable data concerning the effect of superheating on various properties such as fluidity, shrinkage and hot crack

Jan 1, 1945

By Edward A. Loria

A SERIES of papers on the study of austenite grain A size in cast steels has been published recently.'" These studies show that in the as-cast state, the austenite grains are quite large, for they form as the steel freezes at a very high temperature, but a simple reheating above the critical range produces a new set of austenite grains which, in many instances, is finer than ASTM grain sire No. 8. Furthermore, there is no apparent relationship between as-cast austenite grain size and subsequent grain size produced by heat treatment. The as-cast austenite grain size can be determined easily in plain carbon and low alloy steels which produce a continuous grain boundary f errite envelope in the as-cast structure. In the case of cast steels whose alloy content produces greater hardenability and suppresses the proeutectoid ferrite transforma-

Jan 1, 1952

By James A. Barclay, Ralph C. Kirby

The US minerals posture will be increasingly dominated by three interrelated factors. First, when viewed over the long range, the US supply situation can be expected to steadily deteriorate as demand increases. Domestic high-grade ores have been used up, and other nations compete with the US for world supplies. Second, as environmental awareness becomes more acute, an aroused citizenry is demanding that minerals industries conform their operations to rigorous new standards. Finally, the changing energy situation that confronts the US is forcing an appraisal of energy-use patterns on operations previously guided solely by economic principles and not by national priorities. While future US mineral production and consumption patterns are unclear at this time, it is certain that US demand for minerals will continue to outrun domestic supply. Thus, the US is faced with a challenge of producing more minerals and metals from lower grade resources. Meeting this challenge means a strengthening of US research and development efforts, coupled with their application in the remaining leadtimes available. Some specific examples of how the US Bureau of Mines (USBM) is assisting in the processing of low-grade resources follow.

Jan 6, 1975

By J. G. Eberhort

ThE literature of surface phenomena shows that, except for most of the rare-earth elements, surface tensions have now been determined for almost every liquid metal. The situation for liquid metal oxides is, in contrast, characterized by a great scarcity of surface-tension data. A surface-tension correlation between these two classes of substances has been found which provides a means of estimating unknown liquid-oxide surface tensions from the corresponding known liquid-metal surface tension. Lf the surface tension of the liquid metal is a(M) and that of the liquid metal oxide is o(M,Oy), then oxides of all stoichiometries can be brought into one correlation if is plotted against with the surface tensions taken at the respective melting points. The available data is displayed in this fashion in Fig. 1 where the relationship between the surface tensions of the two classes of liquids is found to be The correlation in Fig. 1 is based on data found for nine liquid metal oxides and the corre- sponding liquid metals In cases where several sur-face-tension determinations were available on the same substance, higher values were generally favored over lower ones because they usually indicate greater Sample purity. All of the metal-metal oxide pairs are in good agreement with Eq. [I] except for B-Bz03. The reason for the departure of this pair from the correlation is not understood. To estimate the surface tension of other liquid metal oxides the corresponding liquid-metal surface tension must be found. A nearly complete bibliography of the surface tension of liauid elements is available in the 46th edition of the Handbook of Chemistry and physics. Some additional references on metals are included here for convenience Se,26Sr,'?ThanduZ5). It is also possible to estimate the surface tension of a solid metal oxide or metal from the corresponding liquid-state data. As a liquid material is cooled through its melting point the surface tension increases abruptly by an amount Ao. bondi' has estimated that the maximum value of Aa at the melting point is Ao = Ahf/A [2] where Alzf is the heat of fusion per atom and A is the area per atom in the interface. Thus with heat of fusion and crystallographic data the surface tension of a solid at the melting point can be estimated as o + Ao.

Jan 1, 1967

By Ronald K. Linde

Metastable Ag-Cu solid solutions at two compositions beyond the maximum limits of solubility obtainable by quenching from the solid state were obtained by rapid quenching from the liquid state. The process of transformation of the metastable solid solutions into the equilibrium phases was studied by means of X-ray diffraction intensity measurements and electrical-resistance measurements; metallographic examination was also performed. Results are compared with those for an alloy quenched from the solid state at a composition which exists as a solid solution at elevated temperatures. Activation energies for the trans-formation were computed to be 33,600 * 2500 and 33,100 * 2000 cal per g mole for the 60.1 and 75.0 at. pct Ag;Cu compositions, respectively THE kinetics of precipitation in supersaturated solid solutions obtained by quenching from high temperature has been thoroughly studied in many alloys, and detailed investigations of the early stages of nucleation and subsequent growth of the equilibrium phases have been carried out. All of these studies have been made on alloys quenched from the solid state, however, and it is the purpose of this paper to present some of the results on the kinetics of transformation of metastable solid solutions in Ag-Cu binary alloys whose compositions lie outside of the solid-state limits of solubility. Limits of solubility in the solid state can be increased by rapid quenching from the liquid state. This was first demonstrated by Falkenhagen and Hofmann, who obtained appreciable increases in solubility limits of the elements of the first transition series in aluminum by rapid cooling of liquid alloys through contact with a copper mold maintained at liquid nitrogen temperature.' The same basic idea of cooling a liquid alloy by conduction onto a substrate rather than by convection of a gas or liquid (conventional quenching) has been recently revived and extended to very high rates of cooling by Duwez and his collaborators. The new technique was first applied to Ag-Cu alloys because the existence of a eutectic in this system is not predicted by the Hume-Rothery rules of alloy phase formation. Rapid quenching from the liquid state resulted in metastable solid solutions at all concentrations. The kinetics of decomposition of these metastable solid solutions containing 60.1 at. pct Ag;Cu (eutectic composition) and 75.0 at. pct Ag;Cu is the subject of the present paper. EXPERIMENTAL TECHNIQUES Alloys were made in 10- to 20-g heats using silver of purity 99.99 pet and copper of purity >99.999 pct. Components were weighed accurately to 0.1 mg and melted by induction heating in an alumina crucible under an atmosphere of hydrogen. Weight losses amounted to less than 0.02 ~ct in all cases. Rapid cooling from the liquid state was achieved in an apparatus of the type described by Pietrokowsky. 3 In this technique a freely falling drop of molten alloy is caught between a stationary anvil and a fast moving piston, both anvil and piston being lined with copper. The resulting foils were approximately circular (about 2 cm in diam) and from about 50 to 150 u in thickness, depending on the pressure driving the piston. Metallographic samples were prepared for polishing by edge-mounting foils in Quickmount. The mostef-fective etching procedure was found to be: 10 parts NH4OH (concentrated), 1 part H2O2 (30 pct), 5 parts H2O, swab for 5 to 10 sec. The transformation of the metastable alloys to equilibrium was followed by X-ray diffraction and electrical-resistivity measurements. The peak intensity and the integrated intensity of suitable Bragg reflections of the metastable and stable solid solutions were studied with a Norelco dif-fractometer, using nickel-filtered copper KO radiation. The peaks were step-scanned at intervals of 0.05 deg. Using either a Kelvin bridge or a null circuit with a Leeds and Northrup K-2 potentiometer, the changes in electrical resistance due to phase transformation were measured for specimens cut into strips about 20 mm long and 4 mm wide. All resistivity measurements were carried out at liquid-nitrogen temperature. The isothermal heat treatment was accomplished by sealing the samples in argon-filled aluminum containers with stainless-steel O-rings. Containers were then suspended in wax baths with temperatures in the

Jan 1, 1967

By John Hall

THE recently announced run of three years, nine months and eleven days made by a. crucible steel melting furnace of the Columbia Tool Steel Co., which is claimed as a. world's record, brings forcibly to our attention the great improvements that have been made in the design, construction and operation of the Siemen's regenerative crucible- melting furnace since its introduction in this country. Credit for this advance should be given to the furnace designer, the manufacturer of refractories, and the operators of the furnaces, whose persistent efforts and intelligent co-operation in attacking the problem have resulted so satisfactorily. There are three factors that determine the life of a crucible furnace, or any other furnace for that matter : Design, nature of refractories and conditions of operation; (including the nature of steel melted) and to some extent these factors are interdependent. Thus, for instance, if a crucible furnace is to lie operated single turn and allowed to cool off considerably at night, in order to save fuel, the use of clay-brick melting holes may be advisable, since silica brick is not well adapted to endure rep eated heating and cooling. But the total life of a clay-brick melting hole is necessarily short. Again, if local conditions such as danger of flood make necessary the building of the furnace largely above ground, so that the radiation of beat is promoted, the cooling down of the furnace over the week ends, when no steel is melted, will be considerable-and the contraction of the furnace that results tends to wrack it to pieces. The character of the metal being melted affects the life of the furnace to a great extent. Low-carbon steels and steels made from iron and charcoal require higher temperatures and much longer melting tune than high-carbon steel or steel made largely from scrap; the life of the furnace will be shorter, and the number of heats melted will be much less, when such materials are melted.

Jan 9, 1913

By A. C. Backeberg

There is no South African code for the design of reinforced concrete headframes, and all those erected have been designed on a uniform basis which, up to the present, has tended to be conservative. With certain exceptions designs have generally conformed with British Standard Code of Practice C.P. 114. In the design of reinforced concrete headframes the following loads are taken into account:

Jan 11, 1961

By S. T. Yuster

An analysis has been made of the factors responsible for tilted fluid contacts in petroleum reservoirs. The factors are static and dynamic with the former being controlled by those variables responsible for the capillary rise of fluids, and the latter include rate of formation tilt and hydraulic circulation. The explanation that rate of formation tilt may be responsible for tilted contacts appears untenable. The role of some of these factors in the migration, fractionation. accumulation and possibly the prospecting for oil is indicated. INTRODUCTION While it is generally considered that the segregation of gas, oil, and water in a petroleum reservoir results in approximately horizontal planes separating these phases. there are factor; which modify this simplified picture to a very great extent. Some of these factors are static. and the departure of the fluid interfaces from horizontal may represent a static equlibriun. Some of these factors may be dynamic and the interface positions may be non-equilibrium and represent a steady .state condition. Of course combinations of these two situations may also exist. The reasons most commonly given for this behavior are hydraulic circulation of fluids, change in character of the formation, and a rate of tilt of the formations more rapid than the rate at which the fluids may re-establish an equilibrium. Russell's Principles of Petroleum Geology' contains an extensive discussion of tilted fluid interfaces and their importance in the migration and accumulation of petroleum. Russell cites examples of tilted water tables at Lance Creek, Wyo.; Rock River, Wyo.: Cut Bank. Mont.; Cushing, Okla.: and Graham; Okla. Also given was the Wasson Field of West Texas which has saucer shaped oil-water and gas-oil interfaces with the saucer being deeper in the case of the oil-water contact. The Bradford Field in Pennsylvania has a tilted water table. San Ardo. Coalinga None and some other California field.; have tilled contacts. A recent paper by King Hubbert discuses the effect of hydraulic circulation of the water underlying the oil in a given stratun and it- implications in the accumulation of and drilling for the oil. The foregoing would indicate that tilted fluid interfaces are not uncommon and that it would be of importance to underbtand the forces which are responsible. Further. it would be of interest to examine certain idealized models of situations which may cause tilting with the thought in mind of deriving relatinnships between the important variables. These relationships may only hold exactly for the model* assumed but the results may apply semi-quantitatively to actual formations and at least indicate trends. The discussion will be divided into the effect of static factors and the effect of dynamic factors. STATIC FACTORS It has already been mentioned that one reason given for tilted contacts is a variation in formation properties. Specifically this is a change in the pore size of the formation capilaries. If the internal surface of the reservoir is preferetially wet by water, capillarity will cause the water 10 rise to a greater extent above the free water table in a small capillary than in a large one. Consequently the water-oil contact will be higher in the lower permeability sands than in the higher permeability sand.;. The free water table may be defined as the position the oil-water interface would take if capillarity were absent. Since the phenomenon is the capillary rise of water in an oil environment, a derivation of this shold give a relationship between the variables. Fig. 1 is an idealized model of the situation with a uniform bore circular capillary ubstitttting for the tortuous non.circular formation pore. The upward force.; on the column of water will be equated to the forces downward to give the equilibrium situation. forces upward = force downward where r is the radius of the capillary in ceritimetera. a is the interfacial ten4on oil-water in dynes per centimeter, 0 is the

Jan 1, 1953

By G. P. Sewell

Callow-Type flotation cells, with various modifications, have been employed at the Hayden concentrator since 1917. Other flotation machines, such as matless-air and mechanically agitated types, which have been tested in competition, have failed to handle tonnages or give metallurgical results equal to the modified Callow-type cells on the Ray ores. The original type consisted of wide, deep launders with a relatively flat bottom constructed of porous concrete, through which the air was introduced into the flotation pulp. These cells were constructed to handle the tailings from the gravity concentrating process and no special attention was given to pre- conditioning the pulp ahead of flotation.

Nov 1, 1955

By P. W. George

THE rapid increase in cost of discovering new orebodies by churn drilling in the Tri-State district has led to some attempts to lessen the expense by using geophysical methods. Electrical prospecting was tried three or four years ago, but no successful results were recorded. In 1926, the Federal Mining and Smelting Co. engaged the North American Exploration Co., of Houston, Texas, to make some tests with the torsion, balance. At first, it was thought that the most favorable conditions for discovery of ore deposits with the torsion balance would be in locations where the ore was known to occur at rather shallow depths, FIG. 1.-CROSS-SECTION OF DUENWEG LEASE. therefore the first trial was made at Duenweg, east of Joplin, where some zinc ore had been developed at a depth of 130 ft. The gravity gradients at 61 stations on a tract of about seventeen acres indicated plainly one large zone of maximum gravity and a smaller narrow zone of minimum gravity. Fourteen churn-drill holes, half of which struck .ore, show that all the ore found was located outside the zones of maximum and minimum gravity. In the zone of maximum, gravity the limestone beds were closest to the surface, and the first chert beds encountered were at the greatest depth. The results (shown in Table 1) indicated that the gravity of the limestone was greater than the gravity of the fractured chert together with its orebodies, and probably also greater than the bouldery soil and clay on top of the limestone. A cross-section of the Duenweg lease is shown in Fig. 1.

Jan 1, 1928

By P. W. George

THE rapid increase in cost of discovering new orebodies by churn drilling in the Tri-State district has led to some attempts to lessen the expense by using geophysical methods. Electrical prospecting was tried three or four years ago, but no successful results were recorded. In 1926, the Federal Mining and Smelting Co. engaged the North American Exploration Co., of Houston, Texas, to make some tests with the torsion balance. At first, it was thought that the most favorable conditions for discovery of ore deposits with the torsion balance would be in locations where the ore was known to occur at rather shallow depths, FIG. 1.-CROSS-SECTION OF DUENWEG LEASE. therefore the first trial was made at Duenweg, east of Joplin, where some zinc ore had been developed at a depth of 130 ft. The gravity gradients at 61 stations on a tract of about seventeen acres indicated plainly one large zone of maximum gravity and a smaller narrow zone of minimum gravity. Fourteen churn-drill holes, half of which struck ore, show that all the ore found was located outside the zones of maximum and minimum gravity. In the zone of maximum gravity the limestone beds were closest to the surface, and the first chert beds encountered were at the greatest depth. The results (shown in Table 1) indicated that the gravity of the, limestone was greater than the gravity of the fractured chert together with its orebodies, and probably also greater than the bouldery soil and clay on top of the limestone. A cross-section of the Duenweg lease is shown in Fig. 1.

Jan 1, 1928

By Francis P. Sinn

LOW prices have made 1938 a difficult year for the zinc industry of the world. Particularly in the United States, output had to be radically curtailed to bring production into line with consumption. Despite these unfavorable conditions, some additional plant construction is contemplated. In Jugoslavia, through co-operation with the Government, Trepca Mines is lo build a zinc plant to produce 10,000 metric tons annually, the plant to be ready for operation in July, 1941). Cerro de Pasco is proceeding with its plans for an electrolytic plant in Peru. A pilot plant, to be ready next summer, is under construction. In eastern Canada an electrolytic plant is planned in Quebec to treat concentrates from Yoranda and other mines but no defi-

Jan 1, 1939

By Joseph E. Pogue

The petroleum industry has been involved in Lore collective planning than any other American industry, with the exception of the railroads and utilities, and therefore is of interest as a case study in the experimental attempts to regulate the economic consequences of free competition. Planning is of course an integral part of effective management, hence at the outset a distinction must be clearly drawn between competitive planning and collective planning. By competitive planning is meant the aggregate of plans drawn up and prosecuted by the competing units occupying a field of enterprise; by collective planning is meant a collusion of plans, either originating among some or all competitors, or else imposed upon them, whether accepted or resisted, by some superior authority, usually the state. The prevailing popular concept of "planning" as applied to industry appears to be a program of conduct superimposed upon an industry unwilling or incapable of achieving a socially and economically desirable result under free competition. In this brief and tentative analysis of the subject, competitive planning is left to one side and attention is focussed upon the matter of collective planning as defined above. A basic functional difference between the two categories of planning is that in the case of competitive planning the individual plans are small, numerous, and tend to offset one another when in error; whereas in the case of collective planning, the separate plans are larger in scope, fewer in number, and tend to escape the incidence of the principle of compensation. In viewing the evolution of collective planning in the petroleum industry we find that during the past 20 years there have developed four more or less well defined collective plans and that at the present time the industry is deeply involved in a collective planning trend pointing toward further varieties. The four plans, which are to some degree transitional, may be conveniently named from the chief incidents that led to their formulations. The first collective plan was the program of control developed during the World War and hence called the war plan. The second plan was one originating within the industry in the period between the war and the inflation of the late twenties and called the inventory

Jan 1, 1935

By M. Van Hecke, Y. Berube, L. M. de Smecht

Nitrogen solubilities in water at 100, 200, and 400 psi, in the temperature range 100 to 175C, were determined using an automated system involving flash evaporation and gas chromatography. Rates of gas transfer into a standard laboratory auto-clave were measured by the same technique. The rates at which a gas can dissolve into such a reactor were found to be close to the rates of oxygen consumption observed during the oxidation of several mineral sulfides, indicating that gas transfer might be a rate-limiting step in autoclave leaching.

Jan 1, 1977

By J. E. Crawshaw, Francis B. Foley

In the first report1 disks of steel of known composition and history were exposed, under carefully prescribed conditions, to impacts of explosion products resulting from the explosion of 50-gm. charges of explosives having well-determined rates of detonation, or to impacts of a weight of known mass, falling through measured distances. There were available at the Bureau of Mines Experiment Station five explosives, having rates of detonation of 5716, 4470, 3190, 2296, and 1523 meters per second. It being desired to continue this exposure downward, and no explosives with a lesser rate of detonation being at hand, resort was had to the impact of a falling weight, the differences in the velocity of impact being attained by varying the height from which the weight was allowed to fall. It was expected by this means to demonstrate experimentally that the development of Neumann bands was determined by the suddenness of the deformation of the metal in which they were produced. But while progressive deformations were obtained with the explosive charges, the falling-weight method failed because the tup was progressively deformed, also the disks were so flattened as to be unfit for metallographic examination. A return, therefore, has been made to the use of explosives as the source of energy, an air-gap being interposed between the charge of explosive and the disk, as the effect diminishes as the function of the distance between the charge and the object on which the products of its explosion, or the shock wave from its detonation, impinge. The details of the arrangement of the tests by the air-gap method were the same as those described by Foley and Howell,2 except that after the system had been set up and the desired apparent specific gravity for the explosive attained by tamping it, the small lead block, with the steel disk adhering

Jan 1, 1926

By S. Arthur Krom

(Wilkes-Barre meeting, June, 1911.) RECENT experiments indicate that the usual type of concentrating-table is not only poorly adapted to produce the desired results, but also is based upon an incorrect principle, namely, the use of riffles to perform the work of stratifying the various minerals. We have heard a good deal about riffles for concentrating-tables; exhaustive experiments have been made to discover the proper form of riffle, or to prove the superiority this or that form; disputes and patent-litigation have arisen over the matter of riffles, and thus many have been led to believe that the riffle is the saving-device upon which the process of concentration depends. In the present paper it is proposed to show that the riffle is greatly overrated as to the part it performs in the concentration of minerals, and that, in the near future, it may possibly be eliminated entirely from that process. The experiments in question have shown that the troublesome riffle can be considered of secondary importance at the most, and should be so classed in the construction of a concentrating-table built upon the right lines. The action of any form of riffle on a concentrating-table is such as to upset and retard the process of settling and stratifying the various minerals on the table-deck. From the deck of a riffled table no concentrates can be delivered until the deck is "bedded," that is, until a sufficient amount of metallic values have been fed to the table to spread over a large portion of the deck, forming a substratum of the heavier minerals. This substratum must be maintained by the feed within quite narrow limits, and directly proportional to the rate of discharge from the table, in order that the bed shall not be lost. On the other hand, the riffles having a very lim-

Jul 1, 1911