Search Documents

T. L. Joseph (University of Minnesota, Minneapolis, Minn.)—Mr. Killian is to be commended for his inquiry as to why a decrease of 15.3 pct in coke consumption was accompanied by a decrease of only 1.9 pct in the CO/CO, ratio of the top gas. Although I encouraged him in his efforts to find a more significant and meaningful carbon-gas ratio, the method, calculations, and conclusions originated entirely with the author. Whether we agree entirely with the assumptions underlying his corrected ratio, I think we can all agree that a better ratio is needed, and that he deserves credit for recognizing the need and for doing something about it. To be most useful, the CO/CO, ratio for the top gas should reflect the way in which the carbon is gasified in the furnace, particularly the degree of oxidation and the extent of heat release. The effect of CO, from the decomposition of the limestone and the effect of the reaction of CO and water vapor in the upper part of the furnace on the quality of top gas should be isolated from the effect of more basic reactions such as ore reduction and solution loss. The reduction of sufficient iron oxide to produce a ton of pig iron and the accompanying changes in the proportions of the carbon gases can be expressed on a mol basis as follows: 16.5FeA + 16.5CO - 33FeO + 16.5CO, [1] 33FeO + 33.0CO = 33Fe + 33CO. [2] The CO, from eq 1 normally escapes from the furnace because it does not react with coke at the temperature of its release. However, as much as 50 pct of the CO, from eq 2 may react with coke because it is released at temperatures above 1000°C: 16.5CO. + 16.5CO2 = 33CO [3] Thus we see that the gasification of 16.5 mols or about 200 lb of C in solution loss will regenerate as much CO as is required for the last stage of reduction. The pronounced effect of reaction 3 on the final proportions of CO and CO, in the gas stream is obvious. It also follows that reaction 3 materially alters the heat release but it cannot be entirely eliminated in Lake ore practice. A previous study indicates that 100 lb of solution loss may be necessary to maintain the reducing power of the gas. A reduction of 100 lb from the normal level of 200 lb would mean that over 1,-000,000 additional Btu are released in the process. The 100 lb of additional carbon which will be burned at the tuyeres will release 437,000 Btu and the absorption of 583,000 Btu by eq 3 would be prevented. One of the chief objectives of sized ore burdens and more uniform distribution of the gas stream is to minimize solution loss by completing reduction higher in the furnace and in turn to release the maximum amount of heat from the carbon charged. It was odd, indeed, to find that the use of sized ore and sinter in the careful tests reported by Dobscha had changed the CO/CO2 ratio very little. The author has stressed the close correlation between his corrected CO/CO, ratio and production. A correlation of fuel consumption and the CO/CO, might be more logical. Fuel consumption on the prepared ore burden decreased 15.3 pct whereas the corrected CO/CO2 ratio decreased 19.0 pct. Although this agreement between the reduction in fuel and the reduction in corrected CO/CO2 ratio is not as close as the correlation with tonnage, it indicates the corrected ratio is superior to the normal ratio which decreased less than 4 pct. Some adjustment should be made for the reaction: CO + H2O = CO2 + H2 —700Btu [41 because there is evidence to indicate that about one half of the hydrogen is formed in the upper 21 ft of

Jan 1, 1953

FOLLOWING the passage of resolutions by a num-ber of the western local sections, which have beer printed in previous issues, the Board of Directors appointed a committee consisting of Messrs. Reynders, DeGolyer, Taylor and Merica, to call on the Director of the Budget, and to bring these resolutions to his attention. In response to a request to the committee Mr. Reynders has addressed the following letter to General Lord. In response to a suggestion made in the course of the conference held between you and President DeGolyer of this Institute at Washington on Oct. 6, I present herewith a brief statement of the reasons that have led the mining engineers and metallurgists of this country to urge upon the Government a policy of increasing support from year to year to the United States Geological Survey and the Bureau of Mines. While these are not the only technical bureaus to which we look for data and guidance in our work of winning and rendering useful the mineral re-sources of the country, they are the ones on which we chiefly rely and the usefulness of which extends over all the industries which are based on mines and mining. In calling this matter to your attention and to that of the departments in which these bureaus are situated, I am acting on behalf of a special committee appointed by the Board of Directors and which includes men in close and intimate contact with the iron, coal, petroleum, metals and metallurgical industries; men well qualified by experience and position to voice the real feeling of these industries. The subject is not a new one to our Board, which has long kept a watchful eye on the work of the two bureaus as would be natural in that the American Institute of Mining Engineers, represents the largest group of technical men and executives and the one of most wide-spread interest in the American mineral industries. With 9000 members and. 27 local chapters scattered among the mining states, the Institute is in a peculiarly favorable position to know and to set out the feeling among mining men and metal-lurgists as to the proper scope of activities of these Federal bureaus, the quality of their work, and the gaps in knowl-edge that most need filling.

Jan 11, 1927

By O. B. Ellis, Eric R. Jette, John Chipman

In the study of the chemical reactions orcurring in the open-hearth furnace, it is frequently assumed that a condition of equilibrium between slag and metal is attained. In order to test this assumption it is necessary to have dependable operating data as well as an exact knowledge of the equilibrium state. Considerable progress has already been made in the study of slag-metal equilibria, notably in the earlier work of Hertyl and of Oberhoffer and Schenck2 and in the more recent researches of Krings and Schack-mann3 and of Koerber and Oelsen.4 None of these investigators, however, have employed basic slags comparable to those encountered in basic open-hearth practice, so that up to the present time our only information regarding the equilibria of these slags is based upon observations drawn from steelmaking practice in which there is little assurance that actual equilibrium was attained. The original plan of this investigation was to secure simultaneous slag and metal samples at intervals during the making of an open-hearth heat, recording the heat history in detail and obtaining complete allalyses of slag and metal, then to bring these slag samples into equilibrium with liquid iron in the laboratory induction furnace and thus to determine directly whether or not the observed relationships in the open hearth represent conditions approaching equilibrium. This plan was only partly successful. While slags were obtained from the open hearth under satisfactorily recorded conditions and these were re-melted in the laboratory under equilibrium conditions, changes in slag composition, which accompanied the remelting operation, were so great that the final slag from the induction furnace bore little resemblance to its open-hearth parent and the direct comparison was therefore abnndoned. The results, however, lie within a range of slag composition that is of interest in the making of low-carbon steel. As far as we are aware, they represent the first published laboratory study of equilibria involving slags that contain all the con stituents of basic open-hearth slag. Experimental Heats The first set of measurements on slag-metal equilibrium was made in the Research Laboratories of the American Rolling Mill Co, at Middletown, Ohio. This will be known as series A. The second set was made in the Metallurgical Rescarch Laboratories at Massachusetts Institute of Techology, and will be referred to as series B. Series A.—The induction furnace used has been described. Approximately I kg. of a special ingot iron containing less than

Jan 1, 1941

By John Chipman, Eric R. Jette, O. B. Ellis

In the study of the chemical reactions orcurring in the open-hearth furnace, it is frequently assumed that a condition of equilibrium between slag and metal is attained. In order to test this assumption it is necessary to have dependable operating data as well as an exact knowledge of the equilibrium state. Considerable progress has already been made in the study of slag-metal equilibria, notably in the earlier work of Hertyl and of Oberhoffer and Schenck2 and in the more recent researches of Krings and Schack-mann3 and of Koerber and Oelsen.4 None of these investigators, however, have employed basic slags comparable to those encountered in basic open-hearth practice, so that up to the present time our only information regarding the equilibria of these slags is based upon observations drawn from steelmaking practice in which there is little assurance that actual equilibrium was attained. The original plan of this investigation was to secure simultaneous slag and metal samples at intervals during the making of an open-hearth heat, recording the heat history in detail and obtaining complete allalyses of slag and metal, then to bring these slag samples into equilibrium with liquid iron in the laboratory induction furnace and thus to determine directly whether or not the observed relationships in the open hearth represent conditions approaching equilibrium. This plan was only partly successful. While slags were obtained from the open hearth under satisfactorily recorded conditions and these were re-melted in the laboratory under equilibrium conditions, changes in slag composition, which accompanied the remelting operation, were so great that the final slag from the induction furnace bore little resemblance to its open-hearth parent and the direct comparison was therefore abnndoned. The results, however, lie within a range of slag composition that is of interest in the making of low-carbon steel. As far as we are aware, they represent the first published laboratory study of equilibria involving slags that contain all the con stituents of basic open-hearth slag. Experimental Heats The first set of measurements on slag-metal equilibrium was made in the Research Laboratories of the American Rolling Mill Co, at Middletown, Ohio. This will be known as series A. The second set was made in the Metallurgical Rescarch Laboratories at Massachusetts Institute of Techology, and will be referred to as series B. Series A.—The induction furnace used has been described. Approximately I kg. of a special ingot iron containing less than

Jan 1, 1941

By John Chipman, Eric R. Jette, O. B. Ellis

IN the study of the chemical reactions occurring in the open-hearth furnace, it is frequently assumed that a condition of equilibrium between slag and metal is attained. In order to test this assumption it is necessary to have dependable operating data as well as an exact knowledge of the equilibrium state. Considerable progress has already been made in the study of slag-metal equilibria, notably in the earlier work of Herty1 and of Oberhoffer and Schenck2 and in the more recent researches of Krings and Schackmann3 and of Koerber and Oelsen.4 None of these investigators, however, have employed basic slags comparable to those encountered in basic open-hearth practice, so that up to the present time our only information regarding the equilibria of these slags is based upon observations drawn from steelmaking practice in which there is little assurance that actual equilibrium was attained. The original plan of this investigation was to secure simultaneous slag and metal samples at intervals during the making of an open-hearth heat, recording the heat history in detail and obtaining complete analyses of slag and metal, then to bring these slag samples into equilibrium with liquid iron in the laboratory induction furnace and thus to determine directly whether or not the observed relationships in the open hearth represent conditions approaching equilibrium. This plan was only partly successful. While slags were obtained from the open hearth under satisfactorily recorded conditions and these were remelted in the laboratory under equilibrium conditions, changes in slag composition, which accompanied the remelting operation, were so great that the final slag from the induction furnace bore little resemblance to its open-hearth parent and the direct comparison was therefore abandoned. The results, however, lie within a range of slag composition that is of interest in the making of low-carbon steel. As far as we are aware, they represent the first published laboratory study of equilibria involving slags that contain all the constituents of basic open-hearth slag. EXPERIMENTAL HEATS The first set of measurements on slagmetal equilibrium was made in the Research Laboratories of the American Rolling Mill Co. at Middletown, Ohio. This will be known as series A. The second set was made in the Metallurgical Research Laboratories at Massachusetts Institute of Technology, and will be referred to as series B. Series A.-The induction furnace used has been described.5 Approximately I kg. of a special ingot iron containing less than

Jan 1, 1941

By John Wellington Finch

In August, 1927, the writer examined certain copper deposits in New Mexico1 which occur in beds of sandstones and shale, and in connection therewith reviewed the literature upon deposits of this type. Such deposits are known and have been reported upon at various points in Texas, Oklahoma, Arizona, Colorado, Wyoming and Utah, but in New Mexico they have been given more development than elsewhere and apparently occur there more conspicuously than in the other states. Some 25 years ago the writer examined deposits of similar origin in northern Arizona and more recently other deposits in western and southwestern Colorado, and these examinations have led him to realize how widely scattered are the deposits and how generally noncommercial they are. On superficial development, to one without a comprehension of their geologic nature, they are alluring on account of occasional small amounts of high-grade ore and much misplaced capital has been expended upon them. This paper, therefore, aims to present briefly certain theories of genesis, some details of which may possibly be new, and to lead up to practical conclusions which may be useful to other geologists and engineers. A bibliography of the more important literature upon such deposits is given below.2 Coffin's Bulletin upon the Radium, Uranium and Vanadium Deposits of Colorado, published in 1921, is a particularly clear discussion. The most comprehensive recent statement is Butler's.

Jan 1, 1928

By A. L. Bollens, R. H. Johnson

The appraisal of oil wells, now that we have the age-size method of making composite decline curves, and the present worth of successive time units method of valuation, has its greatest remaining uncertainty in the difficulty of extending into the future the price curve and the composite production curve. The point of attack in this paper is the carrying on (or extrapolation) of the production curve. Led by the valuable discovery of Lewis and Beal that the decline curve is nearer the hyperbolic class, y = (x + a)-", than any other form, the current practice is the graphic method. The data are plotted on logarithmic paper and shifted with successive trials until the line becomes straight. This straight line can then be extended into the future. The method was a great help during the period when, for tax purposes, there was need for a quick method even though the errors were large. Now that we seek greater validity in our methods we find the following faults with the current method. 1. Where the shift is great (it exceeds 10 in some cases) the scale cannot be read with the necessary precision so that the resulting data would give a very irregular and inaccurate curve. 2. Where the curve cannot be straightened on logarithmic paper because of sigmoid shape the method has a serious systematic error. We believe the sigmoid curves to be more common than usually supposed, indeed when one considers the number of variable causative factors this is to be expected. We have therefore been seeking a method that is free from these difficulties and yet not so laborious as fitting a curve to the data and the calculation from the formula which, since it involves looking up logarithms, is unduly time-consuming. The method here described has been developed on the basis suggested by Earl Oliver, that the amount of oil produced per month or year for each reduction of production of a barrel of oil per day could be plotted to advantage. A step forward was made by Earl Carpenter in this laboratory, and some of the

Jan 1, 1928

By R. Maddin, A. Lawley

Single crystal Mo-Re alloys (99.99+ purity), grown by electron bombardment floating zone heating, were deformed in tension at temperatures from -196° to +200°C. At -196oC, Mo-6 pet Re and Mo-20 pct Re alloys deform by slip on systems of the type (101) [1ll]. Above-78oC, the operative slip system is of the type (112) [111], (101) [1ll], or (211) [1ll], depending upon orientation. Mo-39 pct Re alloys deform by twinning and slip at all test temperatures with a (112) [111] type twinning system. Critical resolved shear stress for slip and twinning is calculated as a function of composition and temperature, and the mechanical properties compared with those of less Pure polycrystalline alloys. HEXAGONAL close-packed rhenium, c/a = 1.615, is highly soluble in molybdenum. The bee molybdenum-rich solid solution extends to approximately 42 at. pet Re* at 2500°C,' Fig. 1. Recent work on polycrystalline alloys has shown conclusively that the addition of rhenium to molybdenum improves both the fabricability and the low-temperature ductility.2"5 Similar behavior is observed for W-Re and Cr-Re alloys.5 Initially, Geach and Hughes2 found that the Mo-30 pct Re alloy could be cold rolled to approximately 90 pct reduction before the onset of cracking. The remarkable effect of the rhenium was later confirmed by Jaffee et al. 3-5 with an optimum condition of maximum strength combined with maximum ductility at the Mo-35 pet composition. At higher rhenium contents, the ductility was severely impaired due apparently to the presence of brittle tetragonal s phase, Fig. 1. In the Mo-35 pet Re alloy, at least 110 ppm (parts per million) oxygen could be tolerated before cold workability was reduced. By comparison, the corresponding tolerance figure in unalloyed molybdenum is ~ 10 ppm. The effect of rhenium was considered in terms of: 1) a reduction in oxygen solubility in the lattice; 2) a redistribution of intergranular oxide from grain boundary films to isolated spheres; and 3) the promotion of twinning as a further mode of plastic deformation. Paradoxically, twinning is often associated with brittle fracture in iron and the silicon irons.6'7 Work to date has been restricted to are-melted and powder metallurgy polycrystalline material of ~ 99.9 pet purity. The present investigation was initiated for the purpose of determining the mode and crystallography of plastic deformation of a series of bee Mo-Re alloy single crystals over a wide temperature range from -196o to +200°C. Using high-purity zone-melted material (~ 99.99 + pet purity), the specific role of rhenium in the molybdenum lattice may be understood more fully since effects due to grain boundaries and oxide redistribution will be absent. At the same time, the study provides a comparison of single and polycrystalline deformation behavior. EXPERIMENTAL TECHNIQUES A) Preparation and Purity of Single Crystals. Alloys in the form of either are-cast and swaged or sintered and ground bar, 0.120 in. diam, were obtained from the Chase Brass and Copper Co. Alloy single crystals ~ 8-in. long were grown from the

Jan 1, 1962

By D. V. Doane, G. A. Timmons, W. G. Scholz

Molybdenum of high purity can be produced by direct dissociatiott of commercial molyhdenm disulfide in vacuo at 1600° to 1700°C (2910° to 3090°F). The Product is lower in oxygen than commercially available molybdenzdm powder. Analyses of ingots arc-cast from commercial molybdenum powder, hydrogen-re-cluced from animonium molybdate, and from thermally dissociated molybdenum disulfide indicate that the levels of chemical impurities in these ingots are similar. Equipment now in operation will produce 100-lb hatches of powder product. The paper describes development of processing equipment, control of processing varzahles, handling of the product, and evaluatiotl of the melal produced. MOLYBDENITE (molybdenum disulfide) can be decomposed by heat in the absence of oxygen to produce elemental molybdenum and sulfur, which is evolved as a gas. The temperatures required for the dissociation are above 1370°C (2500°F); the sulfur must be continuously withdrawn to permit the reaction to proceed to completion. This is accomplished by continuous evacuation of the thermal dissociation chamber and condensation of the gaseous sulfur in another part of the system. Cognizance of the fact that the dissociation takes place in two steps is important in controlling the process. Basically, the molybdenite dissociation process has two potential advantages as a method of produc- ing pure molybdenum: 1) The materials entering into the process contain little or no oxygen. Since the process is carried out in vacuum at high temperature, the quantities of interstitial oxygen, nitrogen, and hydrogen in the product should be very low. 2) The process is more direct than the commercia1 method of producing high-purity molybdenum. In the conventional process, molybdenite is roasted to molybdic oxide, the oxide is purified first by sublimation, then by conversion to ammonium molybdate, and finally, the molybdate is reduced in a hydrogen atmosphere (usually in two steps) to the metal lic molybdenum powder. This paper presents a description of the stages in scaling-up of the dissociation equipment and an account of attempts to evaluate the molybdenum produced by thermal dissociation, rather than a report of a fundamental study of the dissociation reaction. Since little has been written on the subject, it is appropriate, before detailing the development of the process, to review briefly the research that has been conducted over quite a period of years. LITERATURE SURVEY The first accounts of the possibility of thermal dissociation of the mineral molybdenite were re-

Jan 1, 1962

By H. J. Hager, P. H. Haskell

Fox the past 20 years Alabama has probably led all other coal-producing districts in the proportion of coal prepared by wet washing. All rail mines, with one exception, and a high percentage of truck mines now wash all coal under 3 or 4 in. Most of this coal has been cleaned by jigs, though within the past few years one or more wettable plants have been installed for cleaning some of the coal from practically all the major seams. These tables supplement either single or multicell jigs usually for one of the following purposes: (I) to wash the finer sizes of raw coal, (2) to rewash the finer sizes of washed coal after they leave the jigs, (3) to retreat jig middling products. The main purpose of this paper is to present cleaning data and operating factors involved in the preparation by tables of the finer sizes of raw coal. The specific information and data pertain to the Mary Lee seam of coal as extracted at three of the mines of the Alabama By-Products Corporation, which produces coal for both by-product coke-oven consumption and the general steam market. The Mary Lee seam has long been recognized by coal-preparation authorities as presenting a very difficult ash-reduction problem. Washing characteristics and physical structure of the seam vary widely. Its thickness ranges from 32 in. with no rock parting to l00 in. with from one to three partings. Over the entire field the bed contains bands of bone and rash. These are distributed throughout the seam cross section. A portion of this bone or bony coal occurs as definite bands 1 in. or more thick; however, some bone is interlocked as layers within the coal and consequently breaks into flakes when the coal is broken. This material is relatively high in ash and its specific gravity varies widely. It has been observed that in most cases in the washing of Mary Lee coal from 10 to 18 per cent of the raw coal is within ±0.10 specific gravity of the attempted point of separation. Therefore with the average wet jig, only with extreme difficulty can a low-ash product be obtained without loss of much marketable coal in the refuse. Without entering into the controversial question as to whether modern washing equipment can efficiently handle simultaneously all sizes up to a given maximum, suffice it to state that the comparatively old-type jigs in service at the Alabama By-Products Corporation's mines could not clean the fine sizes satisfactorily. Therefore, in 1931 that company installed six diagonal-deck tables at the Barney mine, which were installed as an addition to a complete plant cleaning all coal below minus 3 in. The primary washed product is shipped as steam coal and another portion may be prepared as washed nut for domestic trade. These tables are washing 9 tons per hour of raw coal sized to ¼ in. to 0. The washed table coal is mixed with the 3 to ¼ -in. jig product to constitute a 3 in. to o steam coal.

Jan 1, 1941

By V. R. Thompson, R. C. Westgren

In a recent paper,1 the solid-solution strengthening of tungsten and tantalum in a portion of the W-T;-MO-C~ alloy system was described. Additions of tantalum and columbium to tungsten led to significant strengthening, and the introduction of dispersions into these alloys was suggested as a means of further increasing strength. Dispersion strengthening of columbium and molybdenum alloys has been studied extensively.2-4 The approach used to dispersion-strengthen molybdenum alloys appeared equally suitable for tungsten alloys, and, therefore, a brief study was undertaken to determine to what extent the introduction of carbide dispersions would strengthen a solid-solution tungsten-base alloy. A base composition of tungsten and 10 to 12 pet Cb was selected; previous work1 had shown that the tensile strength of this solid-solution alloy was 50,000 psi at 3000°F. For the study of the effects of small additions of

Jan 1, 1964

By Ralph Hultgren, Bernard York, David W. Mitchell

It is a well-known fact that magnesium-alloy castings are apt to be coarse grained if the melt is not superheated several hundred degrees above the melting point before casting. (The casting temperature varies according to the shape of the mold. A typical casting temperature is perhaps 1400°F.) British practice is to heat to 900°C. (1650°F.) for 15 min., cool rapidly to casting temperature, and cast.' In Germany superheating is carried out at 850' to 900°C. (1560° to I650°F.) depending on the amount of scrap used. It is stated that further refinement will be obtained by prolonging the period of superheating or by increasing the superheat temperature to 950°C. (I740°F.).2 In the United States superheating is carried out at 1600' to 1700°F. (871' to 927°C.), perhaps even higher in some places. It is stated that superheating effects are found as low as 1500°F. (816°C.), but several hours are required.3 These commercial treatments lead to grain sizes in sand castings that may vary from 4 to 8 grains per sq. mm.! in heavy sections and from 60 to IOO in 1/2-in. sections to perhaps 380 in thin sections. It is also generally known that the refining effect of superheating is lost if the melt is held for some time at lower temperatures before casting. Aside from these very qualitative statements, there is little to be found in the literature as to the effect of temperature and time of superheat on the final grain size. Because of the uncertainty of these factors, the Office of Production Research and Development of the War Production Board placed a research contract with the University of California, supervised by the War Metallurgy Committee. This research, which was done under the "Restricted" Project NRC-550, is the basis of this paper, which has been released for publication by the O.P.R.D. The material studied was an alloy prepared from carbothermic magnesium. The temperatures required for grain refinement proved to be widely different from those used in practice, as described in the statements in the first paragraph. This difference is attributed to the fact that the magnesium in the specimens was of carbothermic origin instead of the electrolytic magnesium in common use. Materials and Methods The magnesium alloy studied was one of the most popular sand-casting alloys, with a nominal composition of 9 Per cent aluminum, 2 per cent zinc, and 0.1 per cent (minimum) manganese and the balance magnesium. This is designated

Jan 1, 1945

By D. A. Belforti, M. P. Lepie

Spectroscopically pure copper was melted on sapphire plaques in a zydrogen atmosphere. The surface tension of the liquid metal was determined using the sessile drop technique. Measurements were made by direct observation with the aid of a specially const,mcted telescope. The value obtained, 1268 dynes per cm, is compared to that found in the literature. THERE is at this time considerable interest in the use of ceramics for vacuum tubes. The crystalline material is superior to the more conventional glass in mechanical strength, chemical inertness, dielectric properties, ability to withstand high temperatures, and so forth. However, ceramics are much more difficult to seal hermetically with metals than are the glasses. For this reason an investigation was undertaken to determine the wetting and adhesion of metals to ceramics. The sessile drop technique offers a convenient means at elevated temperatures for measuring liquid surface tension, wetting angle, density, spread- ing coefficient, and work of adhesion. Thus, from the contour of a drop of liquid at rest on a solid surface one can obtain a quantitative evaluation of the degree to which the two substances will bond. To this end a special apparatus was constructed so that various molten metals could be observed. Standardization of the apparatus was done initially by measuring the surface tension of copper since this is well documented in the metallurgy literature. Although there are many methods available for the measurement of surface energy,'+ the sessile drop technique has been used most extensively for molten metals and ceramics.5"' Fig. 1 illustrates the dimensions to be measured. From these values, the surface tension of the liquid can be obtained using the Bashforth and bdams' equation and tables.

Jan 1, 1963

By M. M. Fine

THE problem of producing a uniform, medium-fine sand for glass-furnace feed has been of interest to the glass-container industry for many years. In the present investigation of the problem, conducted by the Bureau of Mines in cooperation with the Owens-Illinois Glass Co., Alton, Ill., a satisfactory method of producing such sand was developed. The investigation involved continuous-grinding studies of glass sand with flint and porcelain pebbles, steel balls and rods, and a simultaneous study of classification. The most satisfactory procedure consisted of grinding in a pebble or ball mill followed by a double classification: hydraulic classification to separate the oversize for return to the grinding unit and mechanical classification to remove fines and impurities from the ground sand. The proper application of this flowsheet usually yielded a graded sand containing less iron than the feed even when grinding was done in a steel-lined ball mill. The amount of sand ground into the so-called "dusting" sizes was, in all cases, less than 10 pct. Experiments were made which showed that this very fine sand could be beneficiated to a usable material. Background The advantages in utilizing a uniform, medium-fine sand as a feed for glass furnaces has motivated a considerable amount of research on the ,problem of producing such sand by glass producers and others. For the glass producer, the faster melting rate of such a graded sand offers the possibilities of reduced fuel costs and increased furnace capacity. In addition, there is the likelihood of improving the quality of the melt and thereby reducing the number of seeds (air bubbles) and stones (unrnelted grains) in the finished ware. Although the melting rate of a glass batch depends on other factors in addition to the grain size of the sand, there is experimental evidence to show that grain size influences the melting rate considerably. Potts, Brookover, and Burch' found that when the raw materials (sand, soda ash, and limestone) were always matched in- size, there was a great decrease in the melting time as the grain size of the materials was decreased. They found, too, that when the grain sizes of the soda ash and Limestone were held constant at 40 to 60 mesh, the minimum melting time occurred when 40 to 60 mesh sand was used. The increase in melting time with decrease in grain size beyond 40 to 60 mesh was due, they postulated, to accelerated demixing or separation of batch during melting as the grain size of the sand decreased in relation to the grain size of the other materials. An earlier investigatora found that the highest rate of melting and purifying ordinary glass was obtained when medium-size sand (0.385 to 0.120 mm, correspondingly roughly to 40 to 120 mesh) was used. Although batches containing smaller-size sand were found to fuse more rapidly, the time required to remove air bubbles from such melts actually increased the total duration of the process. Coarsegrained sand, it was stated, increased greatly the times of both melting and purifying. Although the laboratory data are difficult to confirm on a plant scale, observations by the Owens-Illinois Glass Co. indicate a higher furnace capacity of better-quality ware when a medium-fine sand is used in the batch. During the recent war, the glass producer was inclined to overlook a considerable variation in raw materials in the interest of higher production. For instance, table I shows the wide range in the amounts of various screen fractions in sand supplied by one producer to the Terre Haute plant of Owens-Illinois. The sand, from the northern Illinois St. Peter sandstone, represented material used by that plant over a period of a few years during the war. Since the war, the glass industry has insisted on

Jan 1, 1951

By M. M. Fine

THE problem of producing a uniform, medium-fine sand for glass-furnace feed has been of interest to the glass-container industry for many years. In the present investigation of the problem, conducted by the Bureau of Mines in cooperation with the Owens-Illinois Glass Co., Alton, Ill., a satisfactory method of producing such sand was developed. The investigation involved continuous-grinding studies of glass sand with flint and porcelain pebbles, steel balls and rods, and a simultaneous study of classification. The most satisfactory procedure consisted of grinding in a pebble or ball mill followed by a double classification: hydraulic classification to separate the oversize for return to the grinding unit and mechanical classification to remove fines and impurities from the ground sand. The proper application of this flowsheet usually yielded a graded sand containing less iron than the feed even when grinding was done in a steel-lined ball mill. The amount of sand ground into the so-called "dusting" sizes was, in all cases, less than 10 pct. Experiments were made which showed that this very fine sand could be beneficiated to a usable material. Background The advantages in utilizing a uniform, medium-fine sand as a feed for glass furnaces has motivated a considerable amount of research on the ,problem of producing such sand by glass producers and others. For the glass producer, the faster melting rate of such a graded sand offers the possibilities of reduced fuel costs and increased furnace capacity. In addition, there is the likelihood of improving the quality of the melt and thereby reducing the number of seeds (air bubbles) and stones (unrnelted grains) in the finished ware. Although the melting rate of a glass batch depends on other factors in addition to the grain size of the sand, there is experimental evidence to show that grain size influences the melting rate considerably. Potts, Brookover, and Burch' found that when the raw materials (sand, soda ash, and limestone) were always matched in- size, there was a great decrease in the melting time as the grain size of the materials was decreased. They found, too, that when the grain sizes of the soda ash and Limestone were held constant at 40 to 60 mesh, the minimum melting time occurred when 40 to 60 mesh sand was used. The increase in melting time with decrease in grain size beyond 40 to 60 mesh was due, they postulated, to accelerated demixing or separation of batch during melting as the grain size of the sand decreased in relation to the grain size of the other materials. An earlier investigatora found that the highest rate of melting and purifying ordinary glass was obtained when medium-size sand (0.385 to 0.120 mm, correspondingly roughly to 40 to 120 mesh) was used. Although batches containing smaller-size sand were found to fuse more rapidly, the time required to remove air bubbles from such melts actually increased the total duration of the process. Coarsegrained sand, it was stated, increased greatly the times of both melting and purifying. Although the laboratory data are difficult to confirm on a plant scale, observations by the Owens-Illinois Glass Co. indicate a higher furnace capacity of better-quality ware when a medium-fine sand is used in the batch. During the recent war, the glass producer was inclined to overlook a considerable variation in raw materials in the interest of higher production. For instance, table I shows the wide range in the amounts of various screen fractions in sand supplied by one producer to the Terre Haute plant of Owens-Illinois. The sand, from the northern Illinois St. Peter sandstone, represented material used by that plant over a period of a few years during the war. Since the war, the glass industry has insisted on

Jan 1, 1951

CONTENTS PAGE. WHITE, DAVID.-Environmental Conditions of Deposition of Coal. Discussed by E. C. Jeffrey, George H. Ashley, Reinhardt Thiessen, S. W. Parr, David B. Reger, Wilbur A. Nelson, James F. Kemp, E. S. Moore, Homer G. Turner, David White, A. C. Noé, W. A. I. M. van Waterschoot van der Gracht 2 THIESSEN, REINHARDT.-The Constitution of Coal. Discussed by Edward C. Jeffrey, Reinhardt Thiessen, Ralph H. Sweetser, David White 12 TURNER, HOMER G.-Microscopical Structure of Anthracite. Discussed by E. S. Moore, Edward C. Jeffrey, Reinhardt Thiessen, H. J. Rose, James F. Kemp, David White, Clarence A. Seyler, A. C. Noé 14 JEFFREY, EDWARD C.-Coal in Relation to Coke. Discussed by H. J. Rose, David White, E. S. Sinkinson, S. W. Parr, James F. Kemp, Edward C. Jeffrey, Reinhardt Thiessen, Chas. R. Fettke 17 FRANCIS, W., and WHEELER, R. V.-The Resolution of Coal by Oxidation. Discussed by Edward C. Jeffrey, S. W. Parr, E. S. Sinkinson, Reinhardt Thiessen, David White 23 TIDESWELL, F. V., and WHEELER, R. V.-The Constitution of Coal. Discussed by David White, A. C. Fieldner 24 JOLLY, J., and WHEELER, R. V.-Organic Sulfur Compounds in Coal. Discussed by S. W. Parr 25 SINNATT, F. S.-Selective Combustion in Coal. Discussed by J. D. Davis, A. C. Fieldner, Geo. S. Rice, W. M. Grant, H. J. Rose, S. W. Parr, David White 25 COBB, JOHN W.-Nitrogenous Constituents of Coal. Discussed by S. W. Parr, H. J. Rose, Reinhardt Thiessen 28 PARR, S. W., and HOBART, F. B.-Coal and Oxygen. Discussed by J. D. Davis, W. T. Thorm, Jr., S. W. Parr, H. J. Rose, A. C. Fieldner, F. F. Jorgensen, David White, W. M. Grant 30 FIELDNER, A. C., and DAVIS, J. D.-Modern Views of Chemistry of Coals of Different Ranks as Conglomerates. Discussed by S. W. Parr, David White, Reinhardt Thiessen, A. C. Fieldner, Clarence A. Seyler 32 EBY, J. BRIAN.-Contact Metamorphism of Some Colorado Coals. Discussed by Geo. C. McFarlane, W. T. Thom, Jr 35 WHITE, DAVID.-Progressive Regional Carbonization of Coals. Discussed by A. C. Fieldner, Homer G. Turner, W. A. J. M. van Waterschoot van der Gracht, A. C. Noé 37 THOM, W. T., JR.-Moisture as a Component of the Volatile Matter of Coal. Discussed by A. C. Fieldner, S. W. Parr, Clarence A. Seyler, W. T. Thom, Jr., R. D. Hall 39

Jan 7, 1925

By E. S. Greiner

STUDY of the plasticity of germanium or other semiconductor crystals affords unusual opportunities to extend our knowledge of deformation mechanisms. Crystals are available having extraordinary perfection and very high purity. They deform by slip on the systems {111} <110>,1-3 as do crystals of the simple face-centered-cubic structure. Dislocations generated in them during slip are easily revealed in the form of etch pits on either (111) or (100) surfaces.4,5 This fact alone makes possible more detailed studies of mechanisms than is usually the case with metals but, even further, the effect of deformation on their electrical conductivity is very large compared with metals. This comes about not only because the mobility of the charge carriers is reduced, as in deformed metals, but also because the number of these carriers is greatly altered. This latter effect seems closely related to the formation of both line and point imperfections during deformation and thus provides a needed tool for the study of the kinds and distributions of these imperfections. Other investigators have deformed germanium at elevated temperatures by bending,1, 6-8 compres-sion,6, 0,10 tension,2,3,6,11,12 torsion,23 and indentation." Wang and Alexander" have also reported successful indentation at room temperature. Dislocation etch pits consequent to deformation have been observed and studied.7,8,10,18,14,20 The experiments to be de- scribed here include principally the compression and the subsequent annealing of germanium with concomitant studies of etch pits, microstructures, and electrical properties. Both single crystals and heavily twinned specimens were used. Some indentation studies are included. Experimental Methods Plastic compression was effected in the apparatus shown schematically in Fig. 1. It consists of two tantalum platens contained in a helium atmosphere and so arranged that pressure can be applied by a hydraulic press. The specimen between the platens is heated by the surrounding furnace. The specimen is usually a small crystal cube about 0.30 in. on an edge. A control specimen is always inserted so, that it is subject to the same thermal cycle as the one being deformed. This serves to detect any impurity contamination that might accompany the thermal treatment. For high temperature work, where such impurity contamination often occurs, the specimens were first plated with gold whenever subsequent electrical properties were to be determined. This method" is effective in preventing significant contamination of germanium up to temperatures at least as high as 750°C, as evidenced by the constancy of the electrical conductivities of control specimens subjected to the same heat treatments. The total range of temperature used for deformation was from 375°C, the lowest at which significant flow was observed, up to 900°C. Microscopic examination was made after mechanical and chemical polishing and etching. Dislocation pits were revealed with CP-4 etchant by the tech-

Jan 1, 1958

By F. G. Tryon

This paper treats only of the practicability of introducing a standard classification into the records of production and distribution of coal which we try to keep in the Bureau of Mines. From the point of view of gathering and analyzing statistics, the requirements of a satisfactory classification are that it shall be so definite as to eliminate the factor of arbitrary judgment, that it shall be reasonably simple and, finally, and most important, that it shall be understandable to the trade. In other words, to be woven in the statistical record it must be adapted to the raw material which flows in from the 7000-odd mines that produce the coal. The success of any scheme of classification, from the point of view of use, will depend largely on the degree to which it utilizes the accumulated experience of the trade and employs as far as may be possible the accepted trade designations. The experience of the Tidewater Coal Exchange during the war would be an excellent point of departure for a use classification of the coals of the Eastern Appalachians. Although the exchange long since passed out of existence, coal is still quoted and sold by the old pool numbers, and they have shown rather extraordinary vitality. Some years ago, in the Geological Survey, the experiment was tried of getting operators to classify their own coal by offering them a list of standard designations on the annual statistical questionnaire. The results were more amusing than informative. What with the confusion in terminology and the natural temptation to put one&apos;s best foot foremost, there was a general tendency to grade up the quality. Floods of semi-bituminous coal flowed in from many sources, millions of tons from districts where not a pound of that quality has ever been produced. The producers of semianthracite in Arkansas almost without exception would report their product as anthracite and their neighbors in the little Paris field, producing a fine blocky house coal averaging about 17 per cent, volatile, would say, "Our coal isn&apos;t anthracite; it&apos;s a semianthracite." Finally we discontinued the publication of those data as being more misleading than helpful.

Jan 1, 1930

By M. C. Fuerstenau, A. M. Gaudin

A homogeneous suspension is viewed by X-rays. The radiation density seen, affords a measure of the extra absorption due to the solids contained. This radiation density, at a predetermined depth, varies with time. The chart of this relationship gives the desired determination. s it is frequently necessary to know the distribu-rt tion of particle sizes in various products used in industrial applications, a number of means have been devised for these determinations. Some of them include direct microscopic measurement, screening of product, extraction of samples from a settling slurry, air and liquid elutriation, adsorption of gases and liquids, and light absorption. The absorption of light as a means for particle size analysis has been known and employed for some time. X-ray absorption has not received the attention that light has enjoyed primarily because of the complex and costly instrumentation involved with X-rays. In 1954, Brown and Skrebowskil suggested the use of X-rays for this type of determination but did not supplement their suggestion with experiment. In 1958, the authors conducted size analysis experiments on suspensions of quartz with the Trans-viewer: an X-ray unit specifically adapted for sedimentation research, and Rossa conducted experiments in a similar manner in 1959 with a stable gamma emitter, AmZ4l, on suspensions of uranium oxide. To illustrate the applicability of X-ray absorption for analyzing particle size distributions, an essentially mono-energetic and well collimated X-ray beam was used as a source. The beam was made mono-energetic by placing a zirconium filter before the counting window together with feeding the pulses from the proportional counter into a reverter, a device capable of discriminating against pulses of various heights. The sketch in Fig. 1 shows the collimation arrangement in more detail. As shown, the X-ray beam was collimated by inserting a 3/8-in. ID pipe into one of the ports of the X-ray tube and further by two small steel plates with slits 3/32-in. wide and 1/2-in. long placed in front of the window of the Geiger-Mueller (G-M) tube. One of the plates was located 1/2 in. and the other 2 1/2 in. from the window of the counter; both plates were contained in an aluminum holder mounted on the box containing the G-M tube. This type and degree of collimation should eliminate any intensity due to scattered radiation; the transmitted intensity would then be solely a functior. of the absorption by the suspension at that level. Experimentally, homogeneous suspensions of finely ground quartz were prepared, Daxad (a sulfo-nated compound made from wood) was added as dis-persant, and the transmitted X-ray intensity measured as a function of time at a fixed depth in the suspension. In more detail, the experimental procedure involved the following: 1) measuring the transmitted X-ray intensity through the Daxad solution at a predetermined position or settling depth in the absence of solids, 2) placing a known amount of dry solids into the vessel and agitating thoroughly, 3) measuring the transmitted X-ray intensity at time zero (i.e., immediately upon cessation of stirring), and 4) measuring the transmitted X-ray intensity as a function of time (a 10-sec counting interval being chosen and counting being started 5 sec before the desired time). Since a linear relationship exists between percentage solid in a slurry and the logarithm of transmitted intensity for a homogeneous material, the cumu-

Jan 1, 1961

Map

Jan 1, 1957