Search Documents

By R. V. Lundquist

Leaching manganese-bearing materials with NaOH to remove caustic-soluble silica has been demonstrated as a method for upgrading manganese. Those materials containing opaline varieties of silica respond most readily. Spent leach liquors are regenerated by treatment with lime to precipitate calcium silicate and to reactivate the NaOH for leaching. ALL of our larger domestic deposits of manganese are very low grade, but estimated tonnages in these deposits are large enough to constitute a potential strategic reserve of manganese for emergency periods, provided these ores can be upgraded sufficiently to meet industrial specifications. Many types of processes have been suggested for upgrading these ores, several have been studied in pilot plants, and a few have attained limited commercial production for special purposes. The hydrometallurgical process to be described below proposes a leaching operation for removing caustic-soluble silica and other gangue minerals and consequently upgrading a manganese ore or flotation concentrate to a commercially acceptable moduct. It is known that some forms of silica and some silicate minerals are soluble in NaOH solutions under suitable conditions. This new process proposes to use NaOH for removing the soluble materials from manganese ores or concentrates and, as a result, upgrade the manganese content. Since spent leach liquors are not efficient leaching agents the liquor must be treated with lime to precipitate calcium silicate and reactivate the NaOH. Experimental Procedure Manganese-ore samples ground to —35 mesh were leached in iron containers into which the ore sample and appropriate NaOH solutions were placed. Flotation concentrates were already ground to —200 mesh. The slurries were then placed on a hot plate or into a pressure digester and stirred continuously during the period of digestion. Where the- digestion was performed at atmospheric pressures, water lost by evaporation was replaced at regular intervals to maintain approximately a constant volume of slurry. In the pressure digester, volume changes were not controlled. After digestion, the slurry was allowed to cool enough for easy handling, but it was filtered hot, 50" to 70°C, on a Buechner filter. Filtration under these conditions was satisfactory. The resulting filter cake was washed and dried. In most instances, a single leach would not produce maximum extraction of silica from the ore sample; consequently, the dried tailing was treated again in the same manner with a fresh solution of NaOH to obtain an additional extraction of silica. This procedure was repeated a number of times to get the maximum extraction of silica. Usually three or at most four stages of leaching were adequate for this purpose. This leaching procedure was used for obtaining the data reported in this paper on the effects of NaOH concentration, pulp dilution, temperature, and time of digestion on the efficiency of extraction of silica from the ore sample. The experimental procedure does not match industrial methods. consequently tests for counter-current leaching were set up. Data from these tests are not yet complete, but in a qualitative way they indicate that thickeners between stages of leaching will be satisfactory and that the quantity of silica in a leach liquor moving forward to a new solid has only a minor effect on the quantity of silica extracted from the new solid. A pilot plant is now being designed for operation in the near future to test and evaluate the merits of this process.

Jan 1, 1954

By R. M. Briney

A RETURN to nonwar conditions characterized the year 1946. The acquisition and forced use, under Government auspices, of low-grade and uneconomic ores, both foreign and domestic, ceased in 1945, but there was some carry-over into the early months of 1946. The world shipping situation delayed the procurement of some foreign ores, but conditions were improving by the end of the year. No actual shortage of any important alloy was experienced, hence the industry was able to make prompt shipment of orders placed. Price levels of ferroalloys, which had remained virtually constant through the war years, were forced upward, with increases on specific products as conditions necessitated. Standard ferroman-ganese and low-carbon ferrochrome were notable exceptions in that their price did not change. No new ferroalloy smelting plants were constructed. The Defense Plant Corp.. sold the works at Ashtabula, Ohio, to the Electro Metallurgical Co. A new type of ferroalloy furnace was described at the Birmingham meeting of the Electrochemical Society. Known as the "Elkem Rotary Furnace" it is distinguished by a rotating shell. The whole furnace, including shell, refrac-

Jan 1, 1947

By David B. Rushmore

Torches were used by the early Romans for mine-lighting, and these were followed by open lamps or earthen jars filled with tallow or oil, and later by candles. In early coal-mining, explosive gases seldom occurred, and, if they were encountered, the danger of explosion was materially diminished by the absence of any ventilating-system and the consequent insufficient circulation of air to form with the methane an explosive mixture. As the art advanced, the danger of fire-damp became more apparent, and methods for testing the air were resorted to as early as in the fifteenth century. The method of testing consisted in lowering a dog in a basket down the shaft. As soon as he encountered fire-damp he would commence to howl, after which he was withdrawn, and a leafy bush was fastened to the end of the rope and run rapidly up and down the shaft. This so disturbed the accumulation of gas as to cause it to rise out of the shaft. Later this odd method of testing was improved upon through the discovery that a light inserted in a body of fire-damp Gould produce a blue flame. Candles were used for this purpose, and, when fire-damp was thus discovered, brushing or some other primitive method of fanning was resorted to for driving out the gas. In some instances the gas was burned away, regardless of the danger thereby incurred. A man, wearing a well-moistened coat and a mask with glass spectacles, descended in the mine a few hours before each shift. With a long stick, to which was fastened a burning torch or candle, he would crawl on the floor with the stick so raised that the light would sweep the roof and ignite the gas which it encountered. In this position the flame of the explosion would pass over him, after which he would retreat from the gases resulting from the combustion. The occurrence of serious accidents resulted in

Jan 1, 1913

By J. W. Powell, F. H. Spedding

A complete review of the use of chelating agents in the sepa ration of rare earths by ion-exchange is given as well as a concise description of the recent pilot-plant operations of the Ames Laboratory. The two chelating agents which show the greatest promise are ethylenediamine-N,N,N',N'-tetraacetic acid and N'-(2-hydroxyethyl)ethylenediarnine-N,N,N '-triacetic acid. The first successful separations of rare earths by ion exchange were reported in a collection of papers which appeared in the November, 1947, issue of the Journal of the American Chemical Society.1'9 Some of this work was performed at the Ames Laboratory of the A.E.C., the remainder at the Oak Ridge National Laboratory. The processes developed at Oak Ridge, as well as some of the early Arnes methods, employed 5 pct citric acid-ammonium citrate eluant at low pH and were carried out on either H+-state or NH:-state resin beds. These techniques were successful for the separation of small quantities of either naturally occurring or radioactive rare earths and are still used for the isolation of rare-earth activities from fission products. Concentrated citrate is not economical, however, for use in moderate or large-scale rare-earth separations. For this reason, the Ames Laboratory turned its attention to lower concentrations and higher pH's in order to make more effective use of the eluting agent.10-14 Although elutions have been performed successfully over a wide range of conditions, 0.1 pct citrate at a pH of 8.0 is highly recommended for use on H+-state resin beds.15,16 Elu-tion with 0.1 pct citrate in the pH range from 5 to 9 brings about the separation of the constituent rare earths into a series of flat-topped elution bands which progress down the resin bed, head to tail, without actually pulling apart as do the rare-earth peaks which develop when trace quantities are eluted with 0.25M (5 pct) citrate at low pH's. Because of this, elution with 0.1 pct citrate at pH 8.0 do not produce pure rare earths unless sufficient quantities are present to provide developed bands which are at least several inches long on the columns. Although other eluting agents have proved more effective than citrate solutions, articles concerning the use of citric acid for separating rare earths still appear in the literature occasionally. For example, Ketelle and Boyd17 reported some further studies on the separation of rare earths with 5 pct citrate in 1951. They used 270 to 325 mesh Dowex-50 columns at 100°C and a pH of 3.28. vickery18 compared the effectiveness of a number of eluants for the separation of rare earths on NH+4 state Dowex-50 in 1952. He found that citric acid was more efficient than acetic, malic, tartaric, and aminoacetic acids. In 1953, Mayer and Freiling18 reported that citrate was inferior to malate, glycolate, lactate, and EDTA for the resolution of Sm-Eu and Y-Tb mixtures on 250 to 500 mesh, NH+4-state, Dowex-50 at 87°C. pinta20 used 5 pct citrate in the pH range 2.8 to 3.4 to obtain some rare earths for analytical work the same year. Trombe and Loriers21 reported the use of citric acid in their laboratory to separate rare earths in kilogram quantities. Lariers and Quesney22 reported some separations with citrate in 1954. They used 5 pct citrate at pH 2.8 to separate yttrium and the yttrium-group rare earths from the cerium-group rare earths. briers23 used 5 pct citrate at pH 3.2 and 90°C as late as 1956 to isolate thulium in fair purity. For the separation of tracer quantities of rare earths, Mayer and Freiling19 have recommended pH 5.00, 0.24M lactate at 87 °C on 250 to 500 mesh, NH+4-form Dowex-50. Freiling and Bunney24 have also employed lactic acid for the separation of fission-product rare earths. Cunninghame, Size-land, Willis, Eakins, and Mercer25 have reported a 4-hr separation of Y, Eu, Sm, Pm, Nd, and Pr with 1M lactic acid at pH 3.25 on Zeokarb-225 at 87°C. Stewart, et al.,26 reported separation factors for rare earths distributing between Dowex-50 and 0.25M glycolic acid. stewart27 also reported a 30-61 separation of Y, Tm, Er, Tb, and Lu tracers with buffered, 0.25M glycolic acid containing 0.05 pct Aerosol OT. The resin bed was 400-mesh Dowex-50 (X12). The pH of the ammonia-buffered eluant was 3.5. Various aminopolyacetic acids have also been used to obtain varying degrees of separation of the rare earths. In 1951, Fitch and Russell28 investigated iminodiacetic acid (IDA) and nitrilotriacetic

Jan 1, 1960

By J. V. Calara, J. D. Miller

The sign of the surface potential for complex non-reactive ionic solids cannot be predicted solely from consideration of the hydration energy of gaseous ions which constitute the ionic lattice. Accurate analysis of these systems must involve the hydration energy of surface ions, which requires knowledge of the crystal structure, the identification of cleavage planes, and the calculation of binding energies of surface ions. Surface binding energies for ionic solids can be determined if the Surface Madelung Constant is known. A computational technique was developed for the calculation of Madelung Constants for infinite lattices which gives excellent agreement with the values calculated by other more complicated methods reported in the literature. Extension of this technique permits the calculation of Surface Madelung Constants and binding energies of surface ions, [Aus], for semi-infinite solids. The hydration free energy of gaseous ions, [AFh], together with the calculated binding energy of surface ions, [Aus], allows calculation of the hydration energy of surface ions,[AGh], as for the case of the ionic solid, MX: [ ]

Jan 1, 1976

By Alan Stanley

THE MacIntyre Development of National Lead Co. is located at Tahawus, N. Y., in the heart of the Adirondack Mountains. Operations involve the mining and concentrating of a titaniferous iron ore to produce ilmenite and magnetite concentrates. A general description of the operation and metallurgy has been given by Frank R. Milliken.' Pigment plant production demands that the MacIntyre mill produce a 44.7 pct TiO, ilmenite concentrate. To achieve the required ilmenite grade and tonnage it is important that the table concentrate grade be closely controlled. Unfortunately, however, the titaniferous orebody which feeds the MacIntyre mill is not uniform. Ore dressing characteristics vary from one end of the orebody to the other, and from • one level to the next. The changeable nature of the mill feed precludes a single adjustment of the equipment for long periods of time. Thus the operators must constantly watch the equipment to insure a uniform concentrate from the fine and coarse tables and Wetherills, or dry magnetic separators. Chemical assaying of mill products requires about 4 hr from the time the sample is taken until assay results are obtained, and this is available only on a two-shift basis. The ore may change rapidly, even several times during a shift, so that assay results lose most of their control value by the time they are reported to the mill operating crew. Members of the crew have therefore tried to evaluate the table and Wetherill concentrate by visual inspection, since through long experience the shift operators, under most circumstances, can gage closely the grade of the mill products. However, there are times when the physical nature of the ore is radically different from normal. Under these conditions visual inspection is of no value, and at such times final ilmenite as low as 43 pct TiO, has been produced and shipped before the assay results have been received. The specific gravity method of assaying for TiO, has been attempted to eliminate the shipping of ilmenite below normal grade as well as to help control day to day and hour to hour mill production. Table I shows the minerals found in the MacIntyre ore along with their average weight proportions and specific gravities. The first two products considered for the specific gravity method were fine and coarse table concentrates. It was reasoned that these products were essentially ilmenite with the higher specific gravity gangue minerals. Since they were always produced the same way, and the desired grade of TiO, was always constant, the specific gravity of these materials would increase or decrease as the amount of ilmenite increased or decreased. Thus for table concentrates which assayed 40 pct TiOz a constant gravity would invariably be obtained, and as the TiO, value changed the specific gravity would change in direct proportion. The third product considered was Wetherill ilmenite. It was assumed that a desired grade of 44.7 pct Ti02 would also always contain the same amount and type of gangue minerals along with the ilmenite, and thus would always have the same specific gravity. As the TiO, value of the ilmenite concentrate changed so would its specific gravity. Dr. Kenneth Vincent, chief metallurgist of the Baroid Division of National Lead Co. at Magnet Grove, Ark., ran specific gravity tests on 17 samples of the desired products. The lowest specific gravity reading assayed the lowest in TiO, and as the specific gravity increased the trend was for the TiO, assay to increase, see Fig. 1. Since these results warranted further investigation, a 500-g capacity Torsion balance and 250 ml Le Chatelier specific gravity bottles were obtained. Shift samples of fine table concentrate, coarse table concentrate, and final ilmenite were tested. Each sample was split and 85 g weighed on the Torsion balance. The Le Chatelier bottle was filled with water to a zero mark. To avoid wetting the neck of the bottle it was found necessary to do this

Jan 1, 1953

By Alan Stanley

THE MacIntyre Development of National Lead Co. is located at Tahawus, N. Y., in the heart of the Adirondack Mountains. Operations involve the mining and concentrating of a titaniferous iron ore to produce ilmenite and magnetite concentrates. A general description of the operation and metallurgy has been given by Frank R. Milliken.' Pigment plant production demands that the MacIntyre mill produce a 44.7 pct TiO, ilmenite concentrate. To achieve the required ilmenite grade and tonnage it is important that the table concentrate grade be closely controlled. Unfortunately, however, the titaniferous orebody which feeds the MacIntyre mill is not uniform. Ore dressing characteristics vary from one end of the orebody to the other, and from • one level to the next. The changeable nature of the mill feed precludes a single adjustment of the equipment for long periods of time. Thus the operators must constantly watch the equipment to insure a uniform concentrate from the fine and coarse tables and Wetherills, or dry magnetic separators. Chemical assaying of mill products requires about 4 hr from the time the sample is taken until assay results are obtained, and this is available only on a two-shift basis. The ore may change rapidly, even several times during a shift, so that assay results lose most of their control value by the time they are reported to the mill operating crew. Members of the crew have therefore tried to evaluate the table and Wetherill concentrate by visual inspection, since through long experience the shift operators, under most circumstances, can gage closely the grade of the mill products. However, there are times when the physical nature of the ore is radically different from normal. Under these conditions visual inspection is of no value, and at such times final ilmenite as low as 43 pct TiO, has been produced and shipped before the assay results have been received. The specific gravity method of assaying for TiO, has been attempted to eliminate the shipping of ilmenite below normal grade as well as to help control day to day and hour to hour mill production. Table I shows the minerals found in the MacIntyre ore along with their average weight proportions and specific gravities. The first two products considered for the specific gravity method were fine and coarse table concentrates. It was reasoned that these products were essentially ilmenite with the higher specific gravity gangue minerals. Since they were always produced the same way, and the desired grade of TiO, was always constant, the specific gravity of these materials would increase or decrease as the amount of ilmenite increased or decreased. Thus for table concentrates which assayed 40 pct TiOz a constant gravity would invariably be obtained, and as the TiO, value changed the specific gravity would change in direct proportion. The third product considered was Wetherill ilmenite. It was assumed that a desired grade of 44.7 pct Ti02 would also always contain the same amount and type of gangue minerals along with the ilmenite, and thus would always have the same specific gravity. As the TiO, value of the ilmenite concentrate changed so would its specific gravity. Dr. Kenneth Vincent, chief metallurgist of the Baroid Division of National Lead Co. at Magnet Grove, Ark., ran specific gravity tests on 17 samples of the desired products. The lowest specific gravity reading assayed the lowest in TiO, and as the specific gravity increased the trend was for the TiO, assay to increase, see Fig. 1. Since these results warranted further investigation, a 500-g capacity Torsion balance and 250 ml Le Chatelier specific gravity bottles were obtained. Shift samples of fine table concentrate, coarse table concentrate, and final ilmenite were tested. Each sample was split and 85 g weighed on the Torsion balance. The Le Chatelier bottle was filled with water to a zero mark. To avoid wetting the neck of the bottle it was found necessary to do this

Jan 1, 1953

By R. W. Nelson

Methods for determining permeability presented by W. D. Kruger3 in a paper entitled "Determining Areal Permeability Distribution by Calculation" have considerable merit. They can be expected to contribute significantly to analysis of flow in heterogeneous systems. Some rather subtle yet important conditions must be met, however, to assure that the computed permeabilities are correct. The conditions which insure a unique permeability distribution may have been overlooked in the method as proposed and presented in the subject paper. The subtlety of the special requirements may permit good agreement between computed and measured pressures in the reservoir; but the computed permeability may still be in error. The general theory and discussion of the requirements for a unique determination of the permeability distribution are presented elsewhere in more detail.7'8 Accordingly, only major features will be presented here in the notation of Kruger. GENERAL DESCRIPTION OF REQUIREMENTS A brief mention of the route to be followed in showing the special requirements may be helpful. The equation to be solved is a quasilinear, first-order, partial differential equation in the unknown permeability. This equation can be solved through an extension of Lagrange's method by reduction to a system of subsidiary ordinary differential equations. Through consideration of the identity of one of the Lagrange subsidiary differential equations with the stream function, a special interrelationship can be shown. The interrelationship has special significance with respect to the boundary condition. If the boundary function satisfies part of the subsidiary differential equation, no unique solution for the permeability distribution exists. In the physical problem this requirement for uniqueness indicates that the permeability measurements used as a boundary condition can not be along a stream tube. The boundary condition must be along a line, or series of lines, which completely traverse the region and pass through every stream tube.

By J. K. Edgar

For a number of years the production and use of super-purity aluminum (better than 99.99 pct) has been steadily increasing. High-grade lots of. such aluminum show certain outstanding characteristics not found in lower grades containing principally silicon, iron and copper as impurities. One such characteristic is the so-called "self annealing," that is, the re-crystallization of the heavily cold worked metal at room temperature.' Interest therefore is aroused as to the effects of the impurities. It is well known that the amounts of silicon and copper which occur in aluminum of better than 99.95 pct are completely soluble, at least at elevated temperatures (above 200°C). Iron, on the other hand, is known to be fairly insoluble in solid aluminum. Thus, a knowledge of the limits of this solubility would he of considerable use in studying the characteristics of the high purity metal. All investigators have agreed that iron has very low solubility in solid aluminum. Rosenhain, Archbutt and Hanson2 reported traces of an aluminum-iron phase in the "purest samples of aluminum obtainable." Gwyer and Phillips3 reported that an iron constituent was visible under the microscope in metal containing ".0088 per cent iron." Roth4 found that in the solid state the solubility of iron in high purity aluminum was 0.01, 0.01, 0.017 and 0.022 pct at 225, 320, 500 and 600°C respectively. Dix5 working with alloys containing less than 0.03 pct impurities, concluded from microscopic and chemical analyses of eutectic areas that the eutectic composition was close to 1.7 pct iron. Dix placed the eutectic temperature at 65s°C. Archer and Fink,6 using high purity aluminum-iron alloys, found that the hypoeutectic liquidus intersects the eutec-tic horizontal at 1.7 pct. This is in fair agreement with the investigation of the aluminum-iron system by Gwyer and Phillips who placed the eutectic at 1.89 pct iron with a freezing point of 653'C. Preparation and Chemical Analysis oP Alloys Electrolytically refined aluminum (99.991 pct aluminum) and a high purity alumi-num-iron alloy (11.45 Pet iron) were used in the preparation of the alloys for this investigation. To aid in controlling the iron content of the experimental alloys, an alloy of lower iron content was prepared first from these materials. The high purity aluminum was melted and heated to about 700°C in a plumbago crucible coated with alundum cement and the aluminum-iron alloy was then added. The alloy was thoroughly stirred, fluxed and skimmed and then chill-cast into notch bars. The aIlalyses of the three materials are given in Table I. The alloys for the determination of the solid solubility of iron in aluminum were prepared by melting 600 g total of the aluminum plus the required quantity of the aluminum-iron alloy (No. 92531). These

Jan 1, 1949

By Richard W. Lodge

Mr. H. R. Batcheller, of the class of 1894, Massachusetts Institute of Technology, while experimenting with chlorine gas on a certain lot of roasted concentrates, met with the following difficulties: 1. A poor extraction of the gold. 2. A very large consumption of chlorine gas. 3. Inability to precipitate all of the gold from the solutioil containing the AuC1,. 4. The bullion obtained was very base. These difficulties were the same whether the chlorine was generated from H2SO47 MnO29 and salt, or whether H2SO, and bleaching powder were used. They may be accounted for partly by the presence of some arsenic left in the roasted ore, and partly by the presence of copper in the solution containing the AuCI3. It was therefore suggested to try the effect of bromine on a similar lot of ore. The use of this element is, of course, nothing new, but in the following experiments it seemed to present many advantages over chlorine. The material worked upon consisted of some concentrates containing 2.31 ounces of gold per ton, and 34.26 per cent. of arsenic, which would correspoild to about 74.4 per cent. Of

Jan 1, 1896

By L. Burris, G. A. Bennett, P. A. Nelson

Staznless steels ave rrzuch less seuel-ely attacketl by zinc lapov than by molten zinc systems. To determine the applicubility of stainless steels fov equipment items which would be exposed only to zinc vapor, the corvosion resistance of several stainless steels to zinc vapor was investigated in 500-hr- exposuves at 900° C. Two austenilic stainless steels, Types 304 and 3-17, suffered severe intergranular attack. Loss of nickel from these steels and micro-probe crnalyses indicated the probable formation of low-melting zinc-rich phases. Good vesistance to attack by zinc vapor, as determined by metallo-9-rpaphic excr)rtination and physical testing, Loas exhibited by Type 405 stainless steel, a jevvitic steel. Type 440C stainless steel, a tnartensitic steel, although suffering considevable loss in weight, was not structurally weakened. At Argonne National Laboratory liquid zinc and zinc-rich alloys are being employed as solvent media in pyrometallurgical processes under development for recovering and purifying discharged reactor-fuel materials.' Because of the high solubility of most metals in liquid zinc,' there are few metals which can serve as container materials for liquid zinc at temperatures much above the melting point. The poor corrosion resistance of the common metals and alloys to molten zinc has been discussed by Eldred.3 DeKany, Lavendel, and Burris4 tested some of the less-common alloys of the nonrefractory metals and found that they also have poor resistance to attack by liquid zinc and Zn-Mg solutions. Of the metallic materials, only some of the refractory metals such as tantalum, tungsten, and molybdenum and their alloys have shown resistance to attack by liquid zinc.4-7 In the process-development work at Argonne National Laboratory, tantalum and tungsten vessels have been used to hold liquid-zinc alloys. These vessels are housed in stainless-steel equipment, principally to permit maintenance of an inert atmosphere and operation at various pressures. In this experimental work, it has often been observed that Type 304 stainless steel suffers little attack by zinc vapor at temperatures up to about 800 °C. In contrast, severe attack occurs in areas where zinc condenses as a liquid. The extent of attack by zinc vapor on several stainless steels was investigated because there are possible useful applications of stainless steel for equipment items which would be exposed only to attack by zinc vapor. These applications include, for example, housings around processing equipment as indicated above and vapor lines leading from zinc stillpots or retorts to condensers. EXPERIMENTAL EQUIPMENT AND PROCEDURE The experimental procedure consisted in exposing stainless-steel test coupons to static zinc vapor for 500 hr at a temperature of about 900°C. The apparatus, shown in Fig. 1, consisted of a 12-in.-long closed tantalum tube jacketed in Type 304 stainless steel to prevent oxidation of the tantalum. A Zn-10 wtpct Mg* alloy charge of 293 g in the bottom of the

Jan 1, 1965

By Eugene Guccione

FOREWORD-In an interview published in the May 1975 issue of MINING ENGINEERING, one of the world's most respected scientists, nuclear physicist Hans Bethe discussed the reliability of nuclear power plants and their unmatched safety record. The Nobel laureate also refuted the anti-nuclear lobby's claims that nuclear plants emit harmful radioactive effluents. When asked whether the US has sufficient uranium resources, Dr. Bethe replied that "it depends on the time of introduction of the commercial and advanced breeder reactors which, in effect, can generate more nuclear fuel than they consume." The United States has enough U3O8 to last until the breeders can take over in 1995, said Dr. Bethe. But lie warned that extensive environmental damage would be caused if "environmentalists" succeed in delaying the development of the breeder. Any such delays, he noted, would vastly increase the demand for U3O8 in conventional reactors; this, in turn, would impose an immense burden on the US uranium mining industry, which would then have no alternative but to mine the low-grade Chattanooga deposits.

Jan 4, 1977

By C. H. Gerould

I would like to take a moment to consider our polystyrene-silica replica technique, which was developed at the Dow Chemical Co. and which was mentioned in the paper just given by Mr. Thielsch. He stated that he feared that our replica technique would cause difficulty due to deformation of the metal as a result of the application of pressure during the molding process. We at the Dow have never had any reason to suspect that any deformation of the metal was occurring during the molding process. Our procedure has been to heat the polystyrene to a temperature of 160°C. before applying any pressure, at which temperature the polystyrene is a viscous liquid. By so doing the pressure of the polystyrene against the metal is essentially hydraulic and is therefore applied equally in all directions, which we feel should not cause deformation. Our work using this replica technique has brought forth several indications that deformation of the specimen is negligible. These indications are: I. Direct comparisons have been made between the light and electron microscopes when studying a specific spot on a metal surface. These "same spot" studies were obtained by first taking micrographs at high magnification, with a light microscope, of a specific structure that could be readily recog-

Jan 1, 1947

By Glenn B. Southward

The V system of mining used at the Norton mine of West Virginia Coal & Coke Co. was designed as a modified long wall with face conveyors, for use under roof conditions that would not permit regular long-wall methods. This mine is in the Lower Kittanning seam, which averages about 6 ft. in height. There is from 20 to 30 ft. of slate and shale immediately over the coal and above this is a bed of sandstone 40 ft. or more thick; the total cover will vary from 50 to 250 ft. In the room-and-pillar workings, the top in the rooms and headings is generally good but it is

Jan 1, 1924

Discussion of the paper of DWIGHT T. FARNHAM, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 93, September, 1914, pp. 2357 to 2364. DAVID T. DAY, Washington, D. C.-Do you know anything about the character of that clay as to organic matter? H. RIES, Ithaca, N. Y.-No; it is a dark brownish clay, sandy in its nature. The brownish coloring is probably due to organic matter. Some lignite is also present. DONALD W. Ross.*-I have worked at the plant under consideration. I have not seen Mr. Farnham's paper; but in answering the question as to the organic matter, I might say there is practically no organic material scattered through the shale. There are, however, several layers of carbonaceous shale and rather low-grade coal interbedded with the formation. There are two very serious drawbacks-one which threatens to shut down the plant and another which merely means the expenditure of money. The first is taking care of the sediment from the washing away of the overburden. The government is doing extensive work at different points about Lake Washington with a view to creating a fresh-water harbor for Seattle. I understand that they keep at the Denny-Renton people to keep the channel of Cedar River clear. The Denny-Renton Co. can hardly help filling up the channel so long as they continue their hydraulic work, so this is probably one of their most serious problems. The other is this: There is a large percentage of what I should call micaceous shale or sandstone-a sandstone which contains a large amount of light-colored mica. Of course only a limited amount of this can be used in the manufacture of paving brick. As they shoot down the bank after the overburden of gravel and loam is washed away, these large boulders of micaceous sandstone come down. The strata have apparently been crushed where the clay pit is located so that the exact formation cannot be readily determined. These pieces of sandstone, 5 or 6 ft. in diameter, have to be blasted and removed from the shale. They bother both in the open pit and in the tunnel mining. In the tunnel mining of the shale blocks frequently cover the holes in the roof of the tunnel through which the shale is loaded into cars.

Jan 4, 1915

By Daniel C. McLean

Copper concentrates produced by many operations in the United States and South America contain chalcocite (79.9% Cu) as a major component, yet the grades of these concentrates rarely exceed 25 to 28% Cu. Mineralogical studies made by E.P. Cadwell indicated that the low grades were caused by dilution by pyrite rimmed with secondary chalcocite. Laboratory and plant tests proved that concentrates could be significantly upgraded by using a simple, low cost cyanide leaching technique to dissolve the rims and reject the pyrite. The many advantages of this new procedure are cited and the process steps and a typical flowsheet are described.

Jan 1, 1984

By Edwin Ludlow

I DEEPLY appreciate the honor which has been conferred upon me by my election to the presidency of this Institute, as I feel that it is the highest honor a mining engineer can receive, and I also feel that I am especially fortunate in being called to take the presidency in the year following Mr. Hoover, as I may be enabled in that way to carry on the work which he has initiated. The constructive work that Mr. Hoover has inaugurated has been of inestimable benefit in bringing not only this Institute but the entire engineering profession into a place in the public esteem to a degree which it had never before occupied.. This work Mr. Hoover will now carry on in the broader field of the Federated American Engineering Societies, of which he is president. Through that organization the engineers of this country, in all branches of the profession, will be welded into one compact body reaching from the Atlantic to the Pacific, making the united engineering profession a power for maintaining American . . ideals and standards throughout the land.,

Jan 1, 1921

By Ossi E. Palasvirta

The authors are to be congratulated for their interesting article, which thoroughly illustrates the variables inherent in filtration of taconite concentrate. The work and the conclusions based thereon largely parallel the test work done by the writer at the Pilotac plant* and the experience gained with a commercial size agitating disk filter in the same plant. At Pilotac, however, a thorough study was also made of the effect of depolarizing (demagnetizing) the filter feed, and it is the purpose of this discussion to comment on the merits of depolarization of the magnetite concentrate prior to filtering. The work at Pilotac was done in three phases: 1) preliminary laboratory testing with a circular filter leaf of 0.047 sq ft, followed by 2) plant testing using a 4-ft diam, single-disk agitating filter that was purchased on the basis of the pilot tests on the 4-ft model. In the laboratory tests depolarization was achieved by slowly withdrawin4 batches of thickened concentrate from a coil producing an alternating field of about 300 oersteds. In plant tests the standard Pilotac procedure1 was employed, wherein the pulp falls freely through the depolarizing coil.

Jan 5, 1958

By Robert M. Jimeson, James M. Grout

The competitive market potential for solvent-refined coal is estimated and the market advantages are enumerated. Markets are possible in combustion, railroad locomotion, and carbon electrodes. The combustion characteristics are consistent with expected air pollution restrictions on the emission of sulfur and particulate matter. A market potential of sufficient size exists to support the initiation of solvent refining in the United States. The market analysis should help fuel producers determine the advisability of their undertaking solvent refining of coal.

Jan 1, 1972

By William E. Horst, John H. Bassarear

A technique is described which simplifies the standard procedure for measuring the Bond work index of a specific ore and illustrates how to overcome the strict requirements regarding feed size distribution normally encountered in operating plants. Actual results obtained from various process streams in a copper concentrator are presented and the grindability data are discussed in relation to the observed plant performance. This type of information can be used to gain a better understanding of plant behavior and to assist in the evaluation of plant modifications and process control studies.

Jan 1, 1977