Search Documents

By Frank Clemens Smith

The occurrence of the tellurides of gold and silver, even in small quantities, is so rare that their metallurgical treatment has engaged little attention. A residence of several months at one of the few mines in North America the product of which consists entirely of such ore, has led me to arrange a method for its economical treatment. The mine referred to is the Huronian, situated a few miles distant from Jackfish Lake, in Ontario, Canada. The plan proposed is for this peculiar case, and is put on record as possibly suggestive and helpful .in any similar instance, should it occur. Since freight-rates from the mine to the nearest railroad-point were extremely high, and for other economical reasons, the method proposed is modified by the use, as far as possible, of the machinery already at the mine, and is so arranged that bullion instead of concentrates would be obtained as a final product. The ore-vein at the Huronian mine varied in width from about 4 feet at the surface to 2 feet and less at the lowest level—125 feet —and dipped southeast about 88. The rock consisted, on both foot- and hanging-walls, of soft, green Huronian slates carrying much highly crystalline but barren pyrite. The ore carried an inconsiderable amount of galena with iron and copper pyrites, argentite, hessite, sylvanite (or petzite), and probably altaite, the telluride of lead. Near the surface the ore showed considerable native gold, but this disappeared with greater depth. Two complete analyses of minerals containing tellurium are here attached, as they establish the presence of two important compounds: I. Analysis of a mineral supposed at the mine to be sylvanite, but agreeing more closely in composition with petzite (Ag, Au)2 Te: Ag = 41.062 Au =23.691 Te =32.007 Pb = 0.071 SiO2= 0.097 Fe = trace 96.928

Jan 1, 1890

By C. N. Kravig

STANDARD raises at Homestake are 150 ft long. Raises of more than 150 ft, driven with the use of a cage and hoist, are considered long raises- some have been driven more than 900 ft. Long raises have eliminated the need for access drifts on each level when transfer and ventilation raises are driven. These timbered cage raises, 7x9 ft in cross section, include a rock compartment and a combination cage, pipe, and manway compartment. To prevent excessive weight on the timbers, 10x10-in. bearing beams are cemented into hitches cut in the rock at 150-ft intervals. The beams also hold back timber movement caused by daily drawing of rock through the rock compartment.

Jan 6, 1957

By Sherwin F. Kelly

THOUGH the Geophysics Commit- tee limited itself to two sessions this year, both of them marked by a high percentage of absentee authors, even this situation failed to dampen the and or of the ebullient geophysicists, who bandied no small amount of good- humoredlv barbed discussion. Hans Lundherg offered some constructive criticism of last year's report by the Geophysics Education Commit- tee, making a plea for more training in field techniques and less insistence on rigorous theoretical training. Carl Heiland pointed out the necessity of making geophysics and geology courses more attractive in order to draw more students into these fields. Exception was taken to this line of reasoning by Father Macelwane and Sherwin F. Kelly who emphasized the necessity for sound basic training if competent geophysicists were to be turned out. This discussion developed apropos of the report of the Geophysics Education Committee, which had been postponed from the Education Division meetings, but was not read as it was available in mimeographed form. Except for this diversion the morning program fol-

Jan 1, 1944

By O. P. Arora, M. Metzger, G. R. Ramagopal

The rates of grain boundary and general corrosion were surveyed by an approximate method. Quantitative differences between their variations with the strength or cupric ion content of the acid yielded large variations in their ratio, highly selective intergranular attack being observed only under specific chemical conditions. The boundary corrosion rate increased with the copper content of the aluminum; this was attributed to an autocatalytic effect similar to the one shown for general corrosion. High- purity aluminum in hydrochloric acid exhibits striking intergranular corrosion and other structure-dependent corrosion phenomena of fundamental interest. The behavior is highly sensitive to the metallurgical and chemical conditions, the significance of many of which has not been established. The features of the intergranular-corrosion phenomenon, first described by Rohrman,l are summarized in the remainder of this paragraph. Strong attack normally occurs only at high-angle grain boundaries.' Usually 15 to 25 pctHCl is used to obtain a high rate, but this has also been obtained with weaker (7 to 15 pct) acid either by adding cupric or ferric ion to the acid3-5 or by passing an anodic current (-0.1 ma per sq cm).2,3,5,6 The two latter corrosion conditions produce strong attack of low-angle boundaries after certain heat treatments 2-4,5,7 The susceptibility of high-angle boundaries is influenced by the grain-boundary segregation of iron atoms; this increases the slow (µ per month) attack in 10 pct HCl8 but diminishes the rapid (mm per month) attack in 20 pct Hc14 (the present and most previous investigations deal with rapid attack). That segregation of elements other than iron affects intergranular corrosion has not been demonstrated, although analysis of data for iron alloys indicated that at least one other element must be considered.9 Intergranular attack occurs over a wide range of purity although it begins to become obscured above several hundred parts per million (ppm) total im- purities by the severe general corrosion which accompanies the higher iron contents and which is associated with the presence of a second phase or an inhomogeneous distribution of the dissolved iron.4,6,10 The variation of intergranular-corrosion rate with heat treatment1'3-6'"10 can be explained in some cases in terms of the distribution of the iron impurity but is not in general adequately understood. The present work dealt with two questions not previously considered in detail. The first proceeded from the view that the extent to which a special behavior is associated with the boundaries is indicated not by the intergranular corrosion rate alone but by the ratio of the intergranular to the general corrosion rate. A comparison of the two rates was therefore made for one lot of aluminum in acids of varying strength and metallic ion content. The second question was the effect of the copper content of the aluminum. For general corrosion, it has long been known that copper ions introduced into the acid by corrosion of the solid solution are reduced on the aluminum as patches of elemental copper which enhance the corrosion rate by providing cathodes of lower hydrogen overvoltage than were originally present.''-'3 Since the copper patches remain themselves unchanged, their action is "catalytic", and since they are products of corrosion, the effect is "autocatalytic." This phenomenon is significant at copper levels much lower than previously suspected, even at those typical of high-purity aluminum, as the authors have shown in a previous paper.l4 The present work shows that copper content affects intergranular corrosion. With polycrystalline specimens, truly quantitative rate measurernents are not readily made for intergranular corrosion or for general corrosion in the presence of rapid intergranular attack, and previous work in this field has tended to be qualitative. The present study made use of a simple procedure which provided fair approximations to the quantitative corrosion rates and fitted the purpose of surveying the behavior over % wide range of conditions and displaying certain large effects. The approximations involved in this work were usually outweighed by the experimental scatter, which tends to be substantial in a system as sensitive as this one. I) EXPERIMENTAL A. Material. The material procured, Table I, represented three low copper (1 to 3 ppm) lots, two of "normal" copper content (21 and 22 ppm), and two

Jan 1, 1962

By Vittal S. Bhandary, B. D. Cullity

Swaged iron wire has a cylindrical {001} <110> texture. The texture is also cylindrical after re-crystallization in the absence of a magnetic field, but <111> and <112> components are added to this texture when recrystallization occurs in a field. The mecizanical properties in tension and in torsion are not greatly altered by these changes in texture. AS shown in a previous paper,1 cold-worked wires of the two fcc metals copper and aluminum can be made relatively strong in torsion and weak in tension, or vice versa, by proper control of preferred orientation (texture). The deformation texture can be controlled by selection of the starting texture (texture before deformation), because certain initial orientations are stable during deformation. The present paper reports on similar work performed on bcc iron. In this case it was clear at the outset that there was no hope of controlling the deformation texture, which is one in which <110> directions are aligned parallel to the wire axis. (1t has usually been regarded as a fiber texture, but Leber2 has recently shown that it is a cylindrical texture of the type {001} <110>. In either case, <110> directions are parallel to the wire axis.) There is general agreement on this texture among a large number of investigators, which in itself suggests that the starting texture has no influence on the deformation texture. More direct evidence was produced by Barrett and Levenson,3 who reported that iron single crystals of widely varying initial orientations all had a single <110> texture when cold-worked into wire. Thus <110> is a truly stable end orientation for iron and probably for other bcc metals as well. Under these circumstances attention was directed to the possibility of controlling the recrystallization texture. This texture is normally <110> in iron,4 just like the deformation texture. However, it is conceivable that this texture could be modified by a proper choice of the time, the temperature, and what might loosely be called the "environment" of the recrystallization heat treatment. In the present work the environmental factor studied was a magnetic field. The effect of heating in a magnetic field ("magnetic annealing") on recrystallization texture has been investigated by Smoluchowski and Turner.5 They found that a magnetic field produced certain changes in the recrystallization texture of a cold-rolled Fe-Co alloy. The texture of this material is normally a mixture of three components, and the effect of the field was to increase the amount of one component at the expense of the other two. Smoluchowski and Turner concluded that the effect was due to magnetostriction. With the applied field parallel to the rolling direction, the observed effect was an increase in the amount of the texture component which had <110> parallel to the rolling direction. In the Fe-Co alloy they studied, the magnetostriction is low in the <110> direction and high in the <100> direction. Thus nuclei oriented with <110> parallel to the rolling direction will have less strain energy than those with <100> orientations and will therefore be more likely to grow. In a later paper on the same subject, Sawyer and Smoluchowski6 ascribed the effect to magneto-crystalline anisotropy and made no mention of magnetostriction. In the papers of Smoluchowski et al. the intensity of the magnetic field was not reported but it was presumably large, inasmuch as it was produced by an electromagnet. In the second paper6 it is specifically mentioned that the specimens were magnetically saturated. But if magnetostriction has a selective action on the genesis of stable nuclei during recrystallization, that selectivity must depend only on differences in magneto-strictive strains between different crystal orientations and not on the absolute values of those strains. Thus the saturated state does not necessarily produce the greatest selectivity, because the relative difference in magnetostrictive strains between different crystal directions may be larger for partially magnetized crystals than for fully saturated ones.7 In the present work the specimens were subjected to relatively weak fields (0 to 100 oe) produced by solenoids. MATERIALS AND METHODS Armco ingot iron rod (containing 0.02 pct C and 0.19 pct other impurities) was swaged from 0.25 in. in diam. to 0.05 in., a reduction in area of 96 pct. The mechanical properties in tension and torsion were measured as described previously.&apos; Textures were measured quantitatively with chromium or iron radiation and an X-ray diffractometer,8,1 and

Jan 1, 1962

By John McDonald

THIS report is a continuation of an earlier one with a similar title,1 to which the reader is referred for such details of procedure as do not appear here. A brief summary will be given of the objects and methods of the research at this time. It was pointed out in the previous paper that properties of magnesium alloys, as re-ported by different workers, often differ. This was thought to be due to differences in the preparation of the specimens tested. The ideal way to compare alloys would be to prepare each of them in so many ways that reasonable assurance would exist that the best properties of each alloy had been developed. The alloys would then be com-pared on the basis of these properties. The treatment actually given the alloys of these studies is necessarily a compromise with completeness. Nevertheless, enough treatments have been given so that a con-siderable degree of assurance exists that the properties obtained are representative of the alloy as such, and not merely of the manner in which it was worked and heat-treated.

Jan 1, 1940

By T. D. Yensen

I. INTRODUCTION IT is safe to say that of all the different materials that go to make up electrical machinery, iron is the most important. Upon its -magnetic and electrical quality depends not only the efficiency of the machine but, to a very large extent, the cost. Aside from the mechanical strength, there are three characteristics of iron that are of importance in this connection, viz., magnetic hysteresis, electrical resistance, and magnetic permeability. In the homopolar machine, where the magnetic flux is unidirectional, permeability is the only important factor, but in all other machines the flux is reversed in one or more parts and causes losses due to hysteresis and eddy currents. The eddy-current loss depends largely upon the electrical resistance of the iron; the higher the resistance the lower the loss, under otherwise identical conditions. These hysteresis and eddy-current losses cause heating of the machine, and as they depend upon the magnetic density in the iron, this density must be regulated so that the heating shall not be excessive. If the hysteresis and eddy-current Josses and the permeability of the magnetic circuit will permit an increase in the magnetic density, or, in other words, a decrease in the amount of iron, this in turn will mean a decrease in the amount of copper needed, with a consequent decrease in the copper loss. It is thus seen that; indirectly as well as directly, the above characteristics have an important bearing on both the efficiency and the cost of electrical machinery. In general, it may be said that iron for electrical machinery should have the following characteristics: (1) low hysteresis loss, (2) high electrical resistance, and (3) high permeability. These are the characteristics that investigators have been striving to attain since electrical machinery first came into use.

Jan 2, 1916

By Walter Harvey Weed

The enrichment of mineral-veins as a result of the migration of material from an upper oxidized or disintegrated part of a vein to a lower level, where it is redeposited, is now, I believe, quite generally accepted as one explanation of the occurrence of bonanzas in gold- and silver-veins, as well as that of bodies of high-grade ores in cupriferous deposits.* Vogt has called attention† to the fact that there are numerous examples of such rich shoots which are " of exclusively primary character, and dependent upon the laws which governed the original ore-deposition." To this I would add that there are also other examples which are neither of primary origin nor due to descending waters, but. result from a reopening of the veins and their penetration by ascending heated waters whose metallic contents are deposited by reaction with the primary pyrite (and possibly other minerals), forming "secondary" enrichments. My studies of the copper-veins of Butte, Montana, show: That the veins there are of several ages and systems; that the older primary quartz-pyrite veins were reopened by later movements, correlated with a period of volcanic activity; and that they were penetrated by hot alkaline waters carrying copper and arsenic in solution, which was deposited presumably by reaction with the pyrite of the original vein. The enormous development of the Butte deposits, attendant upon the extraction of nearly 10,000 tons of ore a day, has revealed many facts concerning the nature and distribution of the ores. Enargite, the copper sulpharsenate, formerly a relatively rare mineral, is now found to be the chief ore of some veins,

Jan 1, 1903

By G. P. Airey, R. F. Mehl, T. A. Hughes

The coarsening of cementite particles in a ferrite matrix has been studied in a series of steels with 0.15 pct C only and 0.15 pct C plus 1 pct Ni, Mn, and Cr, respectively. Two initial states were employed: quenched nartensite, and quenched and cold-rolled martensite. A series of tempering temperatures between 500&apos; and 700" and tempering times of up to 190 hr were used. The structures were studied by replica and transmission electron microscopy. Particle size distribution curves were determined. From the average size value coarsening curves were obtained. These were plotted in accordance with the Wagner analysis assuming diffusion control. A discussion of the significance of the results is given. L HE reactions occuring upon the tempering of martensite have long engaged the attention of metallurgists. The latter stages, when cementite particles coarsen in a ferrite matrix, have been studied both qualitatively and quantitatively. Studies of such coarsening processes have recently been spurred by the publication of the Lifshitz-Wagner theory1, and the extension of this to the a Fe-Fe3C system by Oriani3 and by Li, Blakely, and einold. Following Wagner the coarsening process is often designated as "Ostwald Ripening". The only quantitative data on the rate of coarsening, except for the work of Hyam and uttin,&apos; in the a Fe-Fe3C system are those of Bannyh, Modin, and odin&apos; for a commercial eutectoid steel and those of Heckel and ereorio" using a pure eutectoid steel. The data of Bannyh, Modin, and Modin have been employed by 0riani3 to derive the a Fe-FeE interface energy. The reaction is one of the most important ones in steel and is worthy of detailed study. This is the purpose of the present study. Laboratory heats were prepared; these were steels with approximately 0.15 pct C, selected so that the num ber of carbide particles would be relatively small and thus so that the overlapping diffusion fluxes would be minimized, presumably a desirable circumstance.&apos;-3 In addition to Fe-C alloys, comparable heats containing 1 pct of Ni, Mn, and Cr, respectively, were included with a view of appraising the effect of alloying elements. This report includes an account of the micro-structures observed, primarily with the electron microscope, and of kinetic data and their interpretation. MATERIALS AND TREATMENT The alloys were prepared from electrolytic iron ("Plastiron") and high-purity graphite; these were melted in a zirconia crucible using a vacuum furnace. The alloy steels were made by adding electrolytic nickel, electrolytic manganese, and "vacuum grade" chromium, respectively, under a partial pressure of argon. Each melt was poured into a mold within the vacuum furnace and cooled in the mold. The ingots were 2 in. in diam. and 8 to 10 in. long. The analysis of the alloys is given in Table I. These ingots were hot-rolled to strip 0.1 in. thick, then cold-rolled to 0.05 in. and each alloy split into two batches. One batch was austenitized at 1200 for 1 min, quenched in cold brine, then cold-rolled to 0.02 in.; samples given this treatment are hereinafter designated as "worked". The other batch was cold-rolled to 0.025 in., austenitized at 1200" for 1 min, and quenched in cold brine; such samples are hereinafter designated as "quenched". These two batches were then tempered, as below. The purpose of the treatment given the first batch was to provide an initial structure of cold-worked martensite, with the expectation that the additional defect structure created by cold work would encourage a higher rate of nucleation of cementite on tempering and hence a more uniform distribution of cementite particles. Individual specimens were sealed in evacuated quartz or Pyrex tubes, then tempered in a muffle furnace. The temperature control was better than 3&apos;C at 700. Tempering treatments wer: performed at 400°, 500°, 550°, 600°, 65o°, and 700C for time periods between 15 min and 190 hr. PREPARATION OF SPECIMENS Specimens for optical and replicalelectron microscopy were mounted, polished conventionally, and etched with 2 pct nital. For electron microscopy, single-stage "formvar" replicas were made, dry-stripped and rotary-shadowed with chromium at an angle of 30 deg. Carbide extraction replicas were prepared from electropolished specimens usirig the method described by Smith and uttin.&apos; Thin foils for electron transmission microscopy were prepared by chemical thinning in an H202-HF bath prior to electropolishing in a chromium trioxide-acetic acid solution. The most

Jan 1, 1969

By I. Fatt

The chromalographic effect refers to the separation of constituents in a moving fluid phase which occurs when the phase is passed over a stationary phase, either solid or liquid, or large areal extent. In performing chemical analyses, the large surface contact areal is provided in the case of gas-solid chromatography by-passing the gas over a porous solid and for gas-liquid chronla tog rap hy by-passing the gas over a porous solid which has been coated with a nonvolatile liquid. The porous medium is usually placed in a cylindrical tube, although it may be a relatively flat sheet as in paper chroma-tography. According to one theory,&apos; the separation results from the difference in time spent by various components in the stationary phahe. A gaseous component which is conlpletely insoluble in the stationary phase, or is not adsorbed on the solid, proceeds unimpeded through the column. The versatility and power of the various types of chromatogruphy for the analysis of complex mixtures are evident from their widespread use in performing chemical analyses and from the large number of symposia, books, and papers devoted to the subject in recent years. Associated developments are the application of chromatography to the determination of heats of solution, heats of adsorption, solubilities orK-values, etc. Gas-liquicl chromatography analyses may be characterized by the manner in which the samples are introduced and displaced from the column&apos;. The three techniques used are known as (1) frontal analysis, (3) displacement analysis, and (3) elution analysis. The frontal analysis is performed by displacing an inert gas from the column by a continuous stream of the sample. As indicated in Fig. l(A), all but the first fraction leaving the column represent mixtures rather than pure components. The displacement analysis is conducted by filling the column with a sample, then displacing it with a more strongly adsorbed or absorbed vapor. The resulting chro-matogram is illustrated by Fig. 1(B). Finally, in the elution analysis a small sample of the mixture to be analyzed is introduced as a "plug" into a Rowing stream of carrier gas to give an elution-type chromato-gram. Fig. l(C). The three techniques may be used to provide models to which Row patterns in other physical situations may be compared. PURPOSE OF THE INVESTIGATION The purpose of this investigation was to determine whether natural reservoir rocks, when coated with crude oil, provided sufficient surface areas to give rise to a chromato-graphic separation of light hydrocarbon constituents. The tests were conducted with the light hydrocar-bons in the gaseous state. SANDS TESTED Two sands of widely different permeabilities have been studied: (1) Ventura core (16 md), and (2) Torpedo sandstone core (578 md).Table 1 gives a description of the cores that were tested. With the exception of one frontal-type flow arrangement which was performed on Core 3, the tests were of theelution-type in which a methane-propane mixture was eluted through the core by means of helium. The Ventura core, when impregnated with a weathered crude from the same field, became so impermeable to gas flow that it was necessary to conduct the tests on the granulated cores (Cores 2 and 3).

By Frank Foote, E. R. Jette

Precision lattice-constant measurements have been widely used in the study of cubic solid solutions but as yet have been rarely applied to noncubic solid solutions. (See, however, references I and 2.) With the high precision at present attainable in the measurement of lattice constants, the X-ray method should be readily applicable to noncubic solid solutions. In the work reported here, hexagonal close-packed magnesium was used as the solvent and either lead, bismuth or gold as the solute. In the magnesium-lead and magnesium-bismuth systems the a and c lattice constants were determined as a function of composition, densities were calculated from these lattice-constant data, these theoretical densities were compared with those directly measured and the solid solubility limit was determined on quenched specimens over a considerable range of temperature. In the magnesium-gold system, the solid solubility is very small but we have obtained an indirect check on the solubility limit previously reported. Materials and Preparation oF the Alloys The magnesium used was obtained from the Aluminum Company of America and was 99.987 per cent pure. Impurities as reported On the label were: Fe, Al, 0&apos;004 per cent; Si, 0.009 per cent; Zn, trace; Cu, Pb, nil. The bismuth was Merck&apos;s analytical grade, minimum purity 99.95 per cent. Maximum impurities as listed on the label were: Fe, 0.008 per cent; Pb, 0.010 per cent; Ag, 0.010 per cent; Cu, 0.005 per cent; Sn, 0.003 per cent; Sb, 0.00; As, 0.000; S, 0.01 per cent. The gold was purified by double precipitation with sulphur dioxide. The lattice constants of these three metals have been previously reported.3 The lead used was test lead, silver free and with a maximum of 0.10 per cent heavy metal impurities. The lattice constant 01 this lead has been measured and found to be 4.94057 ± 0.00016 at 25°C. The alloys were prepared by melting together weighed amounts of the constituent metals in magnesia-lined alundum crucibles under an atmosphere of hydrogen purified by passing over magnesium heated to 500°C. The magnesia lining prevented contamination 01 the alloys with aluminum. Vacuum melting could not be used because of the volatility of magnesium. A high-frequency induction furnace was used for the melting operation and the stirring action of the current resulted in thorough mixing of the constituents. The melts were allowed to freeze in the crucible, the ingots obtained weighed about 10 grams. An extremely thin white film formed on the surface of the melts, sometimes covering only a part of the exposed surface. The ingots were filed clean, placed in small iror crucibles with close-fitting lids and indi. vidually sealed into Pyrex glass tubes Before sealing off, the tubes were alter

Jan 1, 1941

By Frank Foote, E. R. Jette

Precision lattice-constant measurements have been widely used in the study of cubic solid solutions but as yet have been rarely applied to noncubic solid solutions. (See, however, references I and 2.) With the high precision at present attainable in the measurement of lattice constants, the X-ray method should be readily applicable to noncubic solid solutions. In the work reported here, hexagonal close-packed magnesium was used as the solvent and either lead, bismuth or gold as the solute. In the magnesium-lead and magnesium-bismuth systems the a and c lattice constants were determined as a function of composition, densities were calculated from these lattice-constant data, these theoretical densities were compared with those directly measured and the solid solubility limit was determined on quenched specimens over a considerable range of temperature. In the magnesium-gold system, the solid solubility is very small but we have obtained an indirect check on the solubility limit previously reported. Materials and Preparation oF the Alloys The magnesium used was obtained from the Aluminum Company of America and was 99.987 per cent pure. Impurities as reported On the label were: Fe, Al, 0&apos;004 per cent; Si, 0.009 per cent; Zn, trace; Cu, Pb, nil. The bismuth was Merck&apos;s analytical grade, minimum purity 99.95 per cent. Maximum impurities as listed on the label were: Fe, 0.008 per cent; Pb, 0.010 per cent; Ag, 0.010 per cent; Cu, 0.005 per cent; Sn, 0.003 per cent; Sb, 0.00; As, 0.000; S, 0.01 per cent. The gold was purified by double precipitation with sulphur dioxide. The lattice constants of these three metals have been previously reported.3 The lead used was test lead, silver free and with a maximum of 0.10 per cent heavy metal impurities. The lattice constant 01 this lead has been measured and found to be 4.94057 ± 0.00016 at 25°C. The alloys were prepared by melting together weighed amounts of the constituent metals in magnesia-lined alundum crucibles under an atmosphere of hydrogen purified by passing over magnesium heated to 500°C. The magnesia lining prevented contamination 01 the alloys with aluminum. Vacuum melting could not be used because of the volatility of magnesium. A high-frequency induction furnace was used for the melting operation and the stirring action of the current resulted in thorough mixing of the constituents. The melts were allowed to freeze in the crucible, the ingots obtained weighed about 10 grams. An extremely thin white film formed on the surface of the melts, sometimes covering only a part of the exposed surface. The ingots were filed clean, placed in small iror crucibles with close-fitting lids and indi. vidually sealed into Pyrex glass tubes Before sealing off, the tubes were alter

Jan 1, 1941

By Arthur Wade

During the year 1938, there was some drilling in Queensland, New South Wales and Victoria, as follows: Queens1and.—At Hutton Creek, lat. (approx.) 25° 45&apos; S.; long (approx.) 149°, drilling was done by Drillers limited (subsidiary Oil Search) to a depth of 4688 ft., to the Lower Permian(?). There were small gas showings. The hole mas abandoned. At Mt. Bassett, lat (approx.) 26" 20&apos; S.; long. (approx.) 149", Roma Blocks Oil Co. No Liability drilled to a depth of 4033 ft. The hole bottomed in granite. There were small showings of&apos; oil and gas above bedrock in what may be Permian but is not yet determined. The company intends to run a formation tester. New South Wales.—At Kulnura, lat. (approx.) 33" S., long (approx.) 151°, the Kamilaroi Oil Company Ltd. (subsidiary of Oil Search Ltd.) drilled to a depth of 6293 ft. The Permian, probably Upper Marine Series, was reached. Drilling is to continue. Victoria.—At Romawi, lat. (approx) 37" 50&apos; S., long. (approx.) 147" 45&apos;, a dry hole 3246 ft. deep bottomed in the Jurassic and was abandoned. It was drilled by the Governments of the Commonwealth and the State of Victoria. At Lakes Entrance, 1st. (approx.) 37" 50&apos; S.; long. (approx) 748", a small showing of&apos; oil (a few pints a day) was obtained from a well drilled 1275 It., to the Upper Oligocene-Glaucnnitc series, by the Austral Oil Drilling Syndicate, No Liability. Future Drilling Preparations is are being made by companies fur further test drilling in 1939, and the Governments of the Common wealth and the State of Victoria are continuing test holes for information only in the Gippsland district of Victoria. In Papua and New Guinea, no test drilling was done in 1938, but several companies are carrying on geological investigation and it is expected that, some test holes will be drilled during 1939.

Jan 1, 1939

By Arthur Wade

During the year 1938, there was some drilling in Queensland, New South Wales and Victoria, as follows: Queens1and.—At Hutton Creek, lat. (approx.) 25° 45&apos; S.; long (approx.) 149°, drilling was done by Drillers limited (subsidiary Oil Search) to a depth of 4688 ft., to the Lower Permian(?). There were small gas showings. The hole mas abandoned. At Mt. Bassett, lat (approx.) 26" 20&apos; S.; long. (approx.) 149", Roma Blocks Oil Co. No Liability drilled to a depth of 4033 ft. The hole bottomed in granite. There were small showings of&apos; oil and gas above bedrock in what may be Permian but is not yet determined. The company intends to run a formation tester. New South Wales.—At Kulnura, lat. (approx.) 33" S., long (approx.) 151°, the Kamilaroi Oil Company Ltd. (subsidiary of Oil Search Ltd.) drilled to a depth of 6293 ft. The Permian, probably Upper Marine Series, was reached. Drilling is to continue. Victoria.—At Romawi, lat. (approx) 37" 50&apos; S., long. (approx.) 147" 45&apos;, a dry hole 3246 ft. deep bottomed in the Jurassic and was abandoned. It was drilled by the Governments of the Commonwealth and the State of Victoria. At Lakes Entrance, 1st. (approx.) 37" 50&apos; S.; long. (approx) 748", a small showing of&apos; oil (a few pints a day) was obtained from a well drilled 1275 It., to the Upper Oligocene-Glaucnnitc series, by the Austral Oil Drilling Syndicate, No Liability. Future Drilling Preparations is are being made by companies fur further test drilling in 1939, and the Governments of the Common wealth and the State of Victoria are continuing test holes for information only in the Gippsland district of Victoria. In Papua and New Guinea, no test drilling was done in 1938, but several companies are carrying on geological investigation and it is expected that, some test holes will be drilled during 1939.

Jan 1, 1939

By A. U. Seybolt

DURING the course of an investigation of hot corrosion of nickel-base superalloys (combination oxidation-sulfidation attack at high temperature), it was considered possible that sulfur might gain entrance to the alloy in part, at least, by diffusion through the scale. Cr203 is nearly always observed as a prominent component of the oxide scale, and hence some experiments were carried out to examine the tracer diffusion of sulfur through Cr203 at 1000° C in the upper temperature range experienced by jet engine blades and vanes. Some hot-pressed Cr203 discs of quite high density were available from an earlier investigation1 on the rate of crf3 migration through Cr203. The Cr203 was 99.3 pct pure and contained -0.06 pct Fe as the largest metallic impurity. Additional data is given in Ref. 1. In this earlier work it was found that the rate of cation diffusion was independent of the atmosphere of thermal equilibration when using nitrogen, argon, or air, and also that the electrical conductivity of the hot-pressed Cr203 compacts was likewise independent of atmosphere in this range, thus indicating that the de-

Jan 1, 1969

By Robert H. Richards

In the latter part of December a batch of amalgam was retorted and the tin in the retort uncovered while at a low red heat, and allowed to cool slowly to a temperature more suitable for ladling into moulds. It was then ladled and made what appeared to be nice, white, malleable block tin. On February 15th our attention is called to the fact that the tin is brittle, and on examination we find that the molecular condition of the pigs has changed to the extent of one-half its material. The change shows itself by an enlargement appearing on the surface something like crystallization, and comes in spots. The condition of the metal in these spots is very peculiar. It has changed from a malleable metal to a brittle one, with a structure somewhat resembling stibnite, and a color very considerably darker gray than tin. The analyses of the two parts of this tin pig showed the following results: Mercury. Tin. Specific Gravity. Crystalline part,.....2.62 97.24 6.175 Malleable part,.....2.38 97.50 7.387

Jan 1, 1883

By D. H. Shaffer, W. F. Harris, W. M. Hickam, M. H. Loeffler

Experiments have been performed on the quantitative addition to niobium of enriched isotopes 018 and 017 at the 0.1 - 40 micro-gram level and their subsequent recovery. A measured quantity of molecular oxygen of known isotopic concentration is added to niobium metal by oxidation. Recovery of the enriched isotopes as carbon monoxide is by the vacuum fusion technique. Quantitative determinations of the enriched isotopes are made in standard volumes at constant temperature using accurately calibrated micromanometers and the mass spectrometer as pressure measuring instruments. THE presence of low concentrations of nonmetallic impurities in metals can often adversely affect the physical properties of the metal. The increase in hardness and the embrittlement of refractory metals due to oxygen is well known. In metallurgical studies dealing with the diffusion rates or the effect of oxygen on the physical properties of refractory metals, it is often necessary to add small quantities of oxygen to the metal and later recover the total quantity present. It is desirable, therefore, to establish the accuracy with which microgram quantities of oxygen can be added to niobium and recovered by vacuum fusion. The successful addition of microgram quantities of oxygen to metals by the usual manometric techniques and the subsequent recovery by vacuum fusion is difficult because of the uncertainty in the accurate determination of the quantity of oxygen originally present in the metal and because of the chance of contamination by atmospheric oxygen. In order to minimize these uncertainties earlier workers have added quantities of O16 at levels much higher than the oxygen concentrations that are of interest.&apos;-3 In order to eliminate the uncertainty associated with the O16 additions to metals at low microgram levels, experiments have been performed on the quantitative addition of oxygen highly enriched in O17 and O18 at the 0.1 to 40 pg level to niobium and the subsequent quantitative recovery of the isotopes by vacuum fusion. Since the natural abundance of O17 is 0.04 pct and of 0" is 0.2 pct this enriched oxygen provides a uniqueness from interference not achieved in earlier work.&apos;-= A measured quantity of molecular oxygen of known isotopic concentration is diffused into the metal. Recovery of the isotopes in the form of carbon monoxide is by vacuum fusion. The total quantity of gas is determined in standard volumes at constant tempera- ture using accurately calibrated Consolidated Electrodynamics micromanometers and the mass spectrometer for pressure measurements. The molecular and isotopic composition is determined mass spectrometrically. APPARATUS A schematic of the oxygen addition apparatus is shown in Fig. 1. Take-offs are provided for the attachment of the isotope container and for sample bulbs which are used to transfer samples to the mass spectrometer. Metal valves are used throughout the system including the sample bulbs in order to achieve a vacuum of 10"6 mm Hg. Evacuation is accomplished with a 3-stage oil-diffusion pump backed by a mechanical pump. A liquid nitrogen trap is used to remove condensables and to prevent oil vapor from entering the system. A micromano-meter is used for pressure measurements. The furnace assembly is shown in Fig. 2. It consists of a quartz tube joined to the apparatus through a 40/W joint with Apiezon W low-pressure wax. The furnace cap, also a 40/W pyrex joint, is provided with a pyrex hook. The sample is suspended from this hook with a platinum wire. The total volume of the furnace section is 435 ml. All volumes were determined by expanding a known volume of gas at a known pressure into the evacuated system and re-measuring the pressure. Both the micromanometer used on the oxygen addition system and the micromanometer used on the mass spectrometer were compared to a precision

Jan 1, 1961

THE primary interest in the subject of this chapter lies in the fact that various heats of steel made to the same chemical specification do not always have the same properties. The properties considered here, of course, are those inherent in the ingot immediately after solidification and not qualities imparted by variations in subsequent mechanical or thermal treatment. The expression "made to the same chemical specification" is used because some of the variations in properties are due to variations in chemical analysis within the specified ranges of those elements commonly specified and determined. Other variations in properties are due to variations in those constituents of steel (elements or compounds) that are not ordinarily included among the elements specified, thus not a part of the specified "composition." The term "constitution" is used to include not only the specified composition but also the nature and distribution of every element or compound contained in the steel entering the ingot mold ; also included are items such as aluminum oxides and nitrides, presence of soluble gases, and dispersion of nonmetallic particles. When it is considered that the constitution of steel is determined by the addition or absorption into the bath of all such constituents from whatever source, it follows that constitution is of necessity the final result of steelmaking practice. It is the agency through which steelmaking practice operates to control the properties of the steel. The term steelmaking practice is here used in the broad sense, meaning the control of all the materials entering the steel and of the conditions under which the process is carried out. Steelmaking practice, thus defined, establishes the chemical system within which the reactions between components must proceed in obedience to the laws of chemistry. Thus the chemical constitution of the steel is established and, through constitution, the properties of the metal are established. In the preceding chapters it has been shown how the constitu-

Jan 1, 1964

By G. Birkbeck, T. C. Wells

Pearlite morphology in three commercially produced, low-carbon steels has been studied using optical and electron microscopy. A reduction in the cooling rate from 600° to 6°C per hr increased the interlamellar spacing but had little effect on pearlite content. The form of the lamellae was also assessed in terms of a new parameter, the ratio of lamellae length to interhmellar spacing. The variation of this parameter with cooling rate depended on steel composition. For each steel, it would appear that an optimum cooling rate exists at which lamellar pearlite can be produced to the greatest extent, though not necessarily the same extent in different steels. PeARLITE morphology depends principally on steel composition, prior austenite grain size, and either cooling rate or isothermal transformation temperature. Alloying with manganese,&apos;" fine grain size,374 and slow cooling rates reduce the likelihood that a well-developed lamellar structure will be produced. Instead, imperfect structures usually consisting of partly globular carbides are formed in a ferrite matrix. Such structures have been described as granular.1,2,5 degenerate,6 or semi4-pearlite. Manganese additions also progressively lower the eutectoid temperature and the carbon concentration at the eutectoid so so that, for a given carbon content. the pearlite fraction is increased as manganese is added. While the effects of manganese are understood in a general way, quantitative studies of pearlite morphology have been carried out mainly on steels of eutectoid composition;9 little quantitative data is available for low-carbon steels. Certain anomalies exist in the behavior of steels containing -1.5 pct Mn, however. The pearlite morphology in niobium-treated steel differs from that which is generally accepted as typical of low-carbon/manganese steels in that a reasonably well developed lamellar structure is sometimes observed. In the present work, the effects of changes in cooling rate from 600° to 6°C per hr on the pearlite morphology in three commercially produced, low-carbon steels have been studied by both optical and electron microscopy. I) MATERIALS The steels were of the following types: 1) 0.1 pct C, 0.4 pct Mn steel (En 2, a composition similar to specification SAE 1010); 2) niobium-treated, 0.2 pct C, 1 1/2 pct Mn steel (BS 968:1962); 3) silicon-killed 0.2 pct C, 1 1/2 pct Mn steel (En 144, a composition similar to SAE 1320). The chemical analysis for each steel is given in Table I. To facilitate the comparison of pearlite morphology in the three steels, steels 1 and 3 (which were obtained as 1/2-in. plate and 1-in.-diam bar, respectively) were hot-rolled in the laboratory to $ in. thickness, finishing at around 850°C. The BS 968:1962 was received as 1/8-in. plate finished at 885°C and was not further worked. Specimens from each steel were heat-treated in vacuo at 950°C for 1 hr and cooled at rates of 600°, 60°, and 6°C per hr. 11) EXPERIMENTAL Pearlite contents were determined by point counting (500 points) on longitudinal sections mechanically polished and etched in 2 pct nital. Pearlite morphology is usually considered in terms of interlamellar spacing. For pearlite colonies randomly distributed in space and having a true, constant interlamellar spacing So Pellissier et al.9 determined the distribution curve for the apparent spacings of the lamellae on a random section plane. The areal fraction fs of the pearlite colonies occupied by apparent spacings up to a limiting value S is given by:

Jan 1, 1969

By W. M. McKewan

Magnetite pellets were reduced in flowing hydrogen at pressures up to 40 atm over a temperature range of 350° to 500°C. The rate of weight loss of oxygen per unit area of the reaction surface was found to be constant with time at each temperature and pressure. The reaction rate was found to be directly proportional to hydrogen pressure up to 1 atm and to approach a maximum rate at high pressures. The results can be explained by considering the reaction surface to be sparsely occupied by adsorbed hydrogen at low pressures and saturated at high pressures. PREVIOUS investigation1,2 have shown that the reduction of iron oxides in hydrogen is controlled at the reaction interface. Under fixed conditions of temperature, hydrogen pressure, and gas composition, the reduction rate is constant with time, per unit surface area of residual oxide, and is directly proportional to the hydrogen pressure up to one atmosphere. The reduction rate of a sphere of iron oxide can be described3 by the following equation which takes into account the changing reaction surface area: where ro and do are the initial radius and density of the sphere; t is time; R is the fractional reduction; and R, is the reduction rate constant with units mass per area per time. The quantityis actually the fractional thickness of the reduced layer in terms of fractional reduction R. It was found in a previous investigation2 of the reduction of magnetite pellets in H2-H,O-N, mixtures, that the reaction rate was directly proportional to the hydrogen partial pressure up to 1 atm at a constant ratio of water vapor to hydrogen. Water vapor poisoned the oxide surface by an oxidizing reaction and markedly slowed the reduction. The enthalpy of activation was found to be + 13,600 cal per mole. It was also found that the magnetite reduced to meta-stable wüstite before proceeding to iron metal. The following equation was derived from absolute reaction-rate theory4,8 to expfain the experimental data: where Ro is the reduction rate in mg cm-2 min-&apos;; KO contains the conversion units; Ph2 and PH2O are the hydrogen and water vapor partial pressures in atmospheres; Ke is the equilibrium constant for the Fe,O,/FeO equilibrium; Kp is the equilibrium constant for the poisoning reaction of water vapor; L is the total number of active sites; k and h are Boltzmann&apos;s and Planck&apos;s constants; and AF is the free energy of activation. Tenenbaum zind Joseph5 studied the reduction of iron ore by hydrogen at pressures over 1 atm. They showed that increasing the hydrogen pressure materially increased the rate of reduction. This is in accordance with the work of Diepschlag,6 who found that the rate of reduction of iron ores by either carbon monoxide or hydrogen was much greater at higher pressures. He used pressures as high as 7 atm. In order to further understand the mechanism of the reduction of iron oxide by hydrogen it was decided to study the effect of increasing the hydrogen pressure on rebduction rates of magnetite pellets. EXPERIMENTAL PROCEDURE The dense magnetite pellets used in these experiments were made in the following manner. Reagent-grade ferric oxide was moistened with water and hand-rolled into spherical pellets. The pellets were heated slowly to 550°C in an atmosphere of 10 pct H2-90 pct CO, and held for 1 hr. They were then heated slowly to 1370°C in an atmosphere of 2 pct H2-98 pct CO, then cooled slowly in the same atmosphere. The sintered pellets were crystalline magnetite with an apparent density of about 4.9 gm per cm3. They were about 0.9 cm in diam. The porosity of the pellets, which was discontinuous in nature, was akrout 6 pct. The pellets were suspended from a quartz spring balance in a vertical tube furnace. The equipment is shown in Fig. 1. Essentially the furnace consists of a 12-in. OD stainless steel outer shell and a 3-in. ID inconel inner shell. The kanthal wound 22 in. long, 1 1/2, in. ID alumina reaction tube is inside the inconel inner shell. Prepurified hydrogen sweeps the reaction tube to remove the water vapor formed during the reaction. The hydrogen is static in the rest of the furnace. The sample is placed at the bottom of the furnace in a nickel wire mesh basket suspended by nickel wire from the quartz spring. The furnace is then sealed, evacuated, and refilled with argon several times to remove all traces of oxygen. It is then evacuated, filled with

Jan 1, 1962