Search Documents

By L. H. Sjodahl, J. B. Conway

of each particle on grain boundary movement is proportional to the area it occupies on the grain boundary and this increases with the square of the particle radius. In contrast to the impression gained by Tiwari the effectiveness of a particle, as a grain boundary obstacle, increases rapidly as the particle size increases. The counterbalancing factor in a dispersion of constant volume (e.g., those considered by Zener) is of course the rapidly diminishing number of particles, a situation which does not exist in thoria dispersed materials where the volume fraction of thoria remains constant. Although it has been assumed that the Zener approach is valid for the sake of the above argument, it is open to the following objections: 1) It assumes that the effect of many small particles along a grain boundary is cumulative and does not take into account the possibility of each small particle being overcome separately. In this case the boundary will not be able to move forward until the largest particle on the boundary has been overcome. This means that the rate controlling factor will be the rate at which a few relatively large particles are overcome with the remaining small particles playing a negligible role. 2) When the dispersion consists of very small particles the interparticle spacing is usually small compared to the grain size and most particles are located away from grain boundaries where they can play no part. The most efficient dispersion, from a purely geometrical viewpoint, is one where the particle spacing is equal to the grain size so that all the particles are on grain boundaries. Tiwari's second point that voids cannot prevent re-crystallization seems to be unfounded as several workes20-23 have shown that voids alone can retard grain boundary movement and recrystallization. To further convince Tiwari, Fig. 17 shows a void in deformed TD Nichrome holding back a recrystallization interface. Tiwari's explanation for the effect of voids on recrystallization, i.e., they reduce local strain energy and hence lower the driving force for recrystallization may be valid in itself but is irrelevant to the present case where even complete recrystallization after ONE of the more recently proposed expressions for describing stress-strain behavior is that due to Voce.1,2 This equation is usually written: s =s8 ?(s8?so)e??/?c [l] where s is the true stress, ? is true strain, cC is a constant called the characteristic strain, s8 is the asymptotic stress approached at high strain values, and so is the threshold stress at which the plastic deformation begins. While this expression has not been universally accepted as yet it does contain certain features which are consistent with experimental stress-strain behavior. In a more recent publication Hsu, Davies, and Royles3 employed the concept of generalized strain proposed by seth4 and identified a method for linearizing the stress-strain plot. In this approach the generalized strain was given by: where 7 is the generalized strain, 1 is the instantaneous length, 1, the datum length, and n is a constant called the "coefficient of strain measure". A value of n was said to exist which would yield the linearity: s —s+ S[.-(tf] [3] In recent studies of both these approaches, it has been found that while the Voce equation and the gen-

Jan 1, 1970

By R. DiBella, H. Biloni, G. F. Bolling

A study of the detailed relationship between solidification substructure and microsegregation in dilute tin alloys has been continued. New observations reveal that depressions form at the solid-liquid interface not only as an initial form of segregation but throughout the range of increasing constitutional supercooling. In order to show the importance of this node formation it proves convenient to make two simplifications. Although substructure changes continuously as constitutional- supercooling increases,&apos; the following discrete stages may be used for discussion: 1) the planar solid-liquid interface; 2) ordered nodes, or depressions at the interface;&apos; 3) two-dimensional or elongated cells;3 4) regular or hexagonal cells;4 5) distorted cells, or hexagonal cells with branches;4 6) dendrites. It is also convenient to ignore observations made near grain boundaries which interact with the cellular substructure.2-4 And, it should be clearly pointed out that all singular depressions at the solid-liquid interface will be called nodes. Heretofore, the term "node" has been used without clear justification to describe both the truly isolated depression and the junction of cell walls appearing in a later stage of segregation. This usage is continued because it seems proved by the observations. Standard systematic growth of tin crystals was undertaken over a broad range of constitutional supercooling using various added solutes. Except for one or two chance observations, this research failed to reveal any appreciable range of growth conditions over which a disordered array of isolated nodes exists. Even though &apos;some finite range of random instability must exist, it is now concluded that stage one passes very rapidly to stage two. Next, after confirming that stage two passes to stage three by the elongation of isolated nodes: a reexamina-tion of stages three, four, and five followed. Standard metallography showed that pockets of higher solute concentration (for ko < 1) became more numerous in cell walls the more severe the growth conditions. These high-concentration regions must arise from depressions; however, in stage three their segregation is not distinguishable from the segregation of the nodes which join cell walls together. It seems, therefore, that the presence of nodes is causal in the formation of new cell walls, and that the mechanism by which stage three passes to stage four is initiated by nodes. If a similar reasoning is followed, the separation of stage four from stage five appears to be just a convenience that has arisen from the decanted interface observations made in the past. The present observations again show that more severe growth conditions relate directly to an increase in the number of nodes in the hexagonal cell walls. These nodes apparently serve as the origin for lines of segregation extending within the body of a cell, and can thus be assumed to represent the earliest form of branching,* as shown here in Fig. 1. The examination of stage six involved decanted-interface structures as in Fig. 2, which are similar to those considered by Rutter and Chalmers,5 Plaskett and winegard,6 and Hellawell and Herbert,7 and where distinct protrusions are each surrounded by a depressed boundary. The corresponding microsegregation behind the interface, but not far enough behind to allow a smearing of the segregation because of diffusion,4 is shown in Fig. 3. Both the shape of the decanted interface and the segregation pattern behind it

Jan 1, 1968

By V. B. Kurfman

Grain refinement of Mg-Al melts by carbonaceous additions has been attributed to nucleation by aluminum carbide. The effects of process and alloy variables are interpreted and predicted in terms of the dispersion and chemistry of this phase. The grain coarsening action of Be, Zr, Ti, R.E., chlorination, temperature extremes, and prolonged holding times is described. Measures necessary to insure an adequate dispersion of the catalyst are discussed. CARBON inoculation treatments have become fairly well known and used for grain refinement of magnesium alloys containing Al. Although there is general agreement that a nucleation process occurs, the process is not understood and the inoculants are used in a rather empirical fashion. The treatment is applied to the class of alloys containing 3 to 10 pct Al, i.e., AZ31A to AM100A. Typical methods involve melting, alloying, and adjusting the temperature to 1400° to 1450°F. Then 0.01 to 0.5 pct C as CaC2, C6C16, or lampblack is added by any convenient means, and the melt poured within 10 to 30 min. Investigators generally have been impressed by an assumed similarity of this refinement process to superheat grain refinement, which depends on heating approximately the same alloys to a temperature in the range of 1550" to 1650°F, then pouring promptly after the melt is cooled to the pouring temperature. Various predictions have been made that carbon refinement would replace superheating in commercial practice due to reduced process costs, but this replacement has not fully taken place because of production difficulties and conflicting observations. Davis, Eastwood, and DeHaven1 agree with Nelson2 and wood3 in suggesting that an excess of inoculant may be harmful. Wood however says that overtreat-ment is not a problem in production use of hexa-chlorobenzene inoculation, and Hultgren and Mitchell4 claim no evidence of harm from excess additions. Various grain coarsening reactions are known to occur, including the possibility of overtreatment mentioned above. Trace amounts of Be,2 Zr, and Ti may prevent refinement by either a carbon treatment or a superheat. Occasionally treatment with cl25 may cause coarsening, although the Battelle refinement process&apos; uses a CC14-C12 blend. Grain coarsening also tends to occur on holding at temperatures below 1350°to 1400°F, especially after a superheat treatment, and for this reason Nelson2 stresses the desirability of a refinement method useful at lower temperatures for open pot melting practice. Since a carbon treatment can be made to work at temperatures below 1400°F, it seems desirable to investigate the mechanism of the refinement and the mechanisms of the coarsening reactions in order to establish control conditions for use in commercial production. The identity of the nucleating phase must first be established and then the factors affecting its chemistry and physical dispersion must be determined. THE IDENTITY OF THE NUCLEATING PHASE Davis, Eastwood, and DeHaven suggested that the nucleating phase in this system is Al4c3,1 but Mahoney, Tarr, and LeGrand8 disagree, largely because they found no evidence of the compound in alloys after carbon treatment and because there is no indication that aluminum carbide should be unstable over the temperature range used in the superheat treatment. This latter objection is based on the assumption that both the carbon treatment and the superheat treatment introduce the same nuclei. Electron diffraction studies have been made to identify the nucleating phase. Samples of grain refined A292 have been selectively etched SO that clean surfaces are obtained and so that secondary phases are in relief. Electron diffraction patterns from these surfaces have established that the carbon treatment of A292 introduces into the metal a large number of small, plate-like particles with a structure very similar to Al4C3. In most cases, the plate-like nature of the particles prevented positive identification but in the cases where the identification could be made the particles proved to be AIN A14C3. However, enough variation in lattice constants was observed so that all compositions from pure A14C3 to the 50:50 solid solution A1N.Al4C3 were probably present.14 In A14C3 and especially AlN.Al4C3 the A1 atoms occur in layers within which they have the same hexagonal symmetry and spacing as the Mg atoms in a single basal plane of a magnesium crystal. The solid solution spacing lies between the 3.16 of AIN and the 3.3? for Al4C3, in satisfactory agree-

Jan 1, 1962

By W. C. Knoblaugh

ROTARY kilns are adaptable to many fuels, but this paper deals principally with the use of powdered coal. The observations and conclusions presented are based on rotary kilns used in the manufacture of basic refractories for steel furnaces. Solid fuels are pulverized for two principal reasons: (I) ease of control, and (2) rapidity of combustion. By the use of pulverized coal, the operator can increase or decrease the fuel supply by small increments and with very little time lag between the change of control and the resultant change in the flame. This is extremely important in this type of furnace, as the temperature range for maturing the clinker is very narrow. By fine grinding, it is possible to increase the rate of burning of the coal, thereby liberating great quantities of heat within a small space in a short time. Under given conditions, temperature is a measure of the heat liberated per unit of time. To attain the temperatures of 2950° to 3150°F., which are encountered in the manufacture of various steel-furnace refractories, it is estimated that it is necessary to liberate 125,000 to I75,000 B.t.u. per cubic foot of the burning zone per hour. The manufacture of dolomitic refractories is a ceramic process and, as is true in most such processes, the material must be subjected to a certain critical temperature for a certain length of time in order to complete the reaction. If the time of reaction is reduced, the temperature must be increased; in other words, if the rate at which the material flows through the hot zone of the kiln is increased, the temperature of the hot zone must be increased to compensate for this shorter exposure to the flame. FIRING WITH PULVERIZED COAL Fig. I is a line drawing of a rotary kiln with the attendant equipment indicated in their relative positions. The kiln proper consists of a sloping, refractory-lined steel tube rotating slowly about its longitudinal axis (0.75 r.p.m.), and is countercurrent in operation in that the raw feed is introduced at the stack end and gradually approaches the zone of highest temperature at the lower end, where the fuel is introduced. Before 1930, the usual method of firing a rotary kiln was to store the coal in the pulverized form and then feed from this storage to the kiln as needed. This proved unsatisfactory and dangerous because of dust explosions and the inability to obtain an even feed to the kiln caused by arching of the coal in storage and flooding of the coal feeders. In later years the practice has been to store the raw coal and grind it as it is needed. Such a layout is indicated in Fig. I. The coal is stored in bins, charged from the top and drawn from the bottom into recording scales and then into some type of unit pulverizer. There are a number of good pulverizers on the market, each incorporating features that the manufacturer considers outstanding.

Jan 1, 1946

By P. R. Schmidt, N. J. Themelis

A study zvas made of the deoxidation of copper at 1170°C by injecting a jet of carbon monoxide vertically upwards into the melt. The effects of submersion depth (2 to 20 cm), orifice diameter (& to 5 in.), and gas velocity (100 to 3650 ft per sec) were examined. In the oxygen range 0.1 to 1.0 pct 0, the overall rate was conlrolled by gaseoLcs mass Lransfer. The results were interpreted in terms of a rate coefficient per unit depth which was found to be constant with distance along the jet axis and nearly proportional to the orifice Reynolds number in the range 1000 < NReo < 9100. AS the gas flow rate through an orifice submerged in a liquid is progressively increased, at least three regions of bubble formation may be distinguished. At very low rates, the formation of bubbles is practically a static phenomenon, depending on the orifice diameter, the liquid surface tension, and the densities of the two phases. In this region, the bubble size is constant while the frequency of bubble formation increases with gas flow rate.&apos;-3 At higher flows (500 < NR~, < 2100), the frequency of bubble formation reaches a steady value and the bubble size increases with gas flow rate; when the bubbles issuing from the orifice become so large that they start coalescing to form larger bubbles, the turbulence induced in the liquid by the passage of previous bubbles shatters them into small bubbles of varying size. Finally, for gas velocities in the intermediate and turbulent regions of flow (NR,, > 2100) a tangential separation surface is created around the jet and momentum transfer takes place between it and the surrounding liquid medium. The entrainment of liquid and the resulting deceleration of the gas-liquid dispersion causes the jet to expand forming a characteristic jet cone. The large velocity and density differences between the jet and the liquid result in a high degree of instability and the jet envelope fluctuates rapidly.The characteristic jet cone can be observed by means of time exposure photographs such as those shown in Fig. 1 for an air jet introduced vertically upwards in a water bath. High-speed photography has showns that the gas-liquid dispersion within the cone consists of small bubbles the size of which depends mainly on the jet orifice diameter and Reynolds number. In the laminar region of flow, the following correlation was obtained by Leibson: The results of Liebson et a1.&apos; are plotted in Fig. 2. It can be seen that the region 2000 < NReo c 10,000 is not well-defined experimentally. In the entrance to the fully turbulent region of flow (NR,, = 10,000), the mean bubble diameter decreased to about 0.4 cm and varied only slightly from there on according to the correlation:

Jan 1, 1968

By R. J. Mellen

IN a chloridizing roasting and cyanidation plant treating a manganese-silver ore, certain experiments pointed out the way to an improvement in roasting conditions by a change in the degree of crushing. The following short article is simply a description of the various changes that were necessary throughout the plant and of the results obtained. There is nothing unusual in these changes but they are of some interest in that they constitute a good many of the alterations usually resorted to in increasing production. In the beginning, the changes were brought about by an experiment that was not successful, but which clearly pointed to means of improving the operation, and is an example of the fact that often experimental work may result in failure and still be of value in arriving at correct fundamentals. This experiment also shows how far a metallurgist can get out of line in his deductions, particularly in a field with which he is not thoroughly familiar. The ore at the plant of Compania Minera Kildun y Anexas is crushed through a 13-in. gyratory, a 3-ft. standard Symons cone crusher and a set of 16 by 42in. rolls, the latter in closed circuit with two Tyler 400-mesh screens. The crushed ore is then conveyed to two fine-ore bins. These provide storage and feed for two 6 by 90-ft. kiln roasters, which discharge directly to coolers. The coolers in turn discharge to a 6 by 12-ft. ball mill, where the ore is ground for cyanidation. Laboratory and pilot-plant tests previous to the mill construction had indicated that minus ¼ -in. crushing was satisfactory for roasting, although results did not vary greatly with some coarser or considerably finer crushing. The plant was designed for a capacity of 300 tons per day on this basis. After a few months operation, the initial operating problems were overcome and the anticipated milling rate was reached but the results being obtained were not really good. The plant seemingly did not have much excess capacity in any department but the roasting operation was the most critically limiting factor both as to tonnage and the results obtained. If this could be improved there seemed some possibility of improving the total tonnage rate to some extent. Segregation of the calcine into various screen sizes showed that the coarser sizes ,were not giving the expected recoveries. In all of the laboratory and pilot-plant testing, any limiting conditions as to the percentage of salt used, temperatures, feed rates, etc., had affected the fine material more than it had the coarse, and even in making laboratory tests at this time the mill conditions could not be exactly duplicated. Further laboratory testing indicated that a segregation of the crushed ore into a coarse and fine product for roasting might result in some improvement in roast-

Jan 1, 1945

By P. D. Merica

The remarkable phenomena exhibited by the aluminum alloy known as duralumin were discovered during the years 1903-1911 by A. Wilm1,2 and have been described by him and by others. 3 4 5 6 The unusual feature of this alloy is the fact, as was shown by Wilm, that it can be hardened quite appreciably by quenching from temperatures below its melting point followed by aging at ordinary temperatures, which consists merely f allowing the material to stand at these temperatures. The hardness is not produced by the quenching alone but increases during the period of aging, which may be from one to three days. Cohn3, 5 gives data showing the increase of hardness of duralumin during aging, after quenching in water from about 450° C. Upon annealing, the alloy so hardened by aging is softened exactly as is hardened steel. The composition of this alloy usually varies within the following limits: Copper, 3 to 4.5 per cent.; magnesium, 0.4 to 1.0 per cent.; manganese, 0 to 0.7 per cent.; aluminum, balance; iron (as impurities), 0.4 to 1 per cent.; silicon, 0.3 to 0.6 per cent. Its density is about 2.85. It is used only in the forged or rolled condition. This alloy has been produced for some years commercially and is in demand for the fabrication of parts for which both lightness and strength are required, such as for aircraft. Its tensile strength will average 50,000 to 60,000 lb. per. sq. in. (3515 to 4218, kg. per sq. cm.) after appropriate heat treatment, such as that described by Wilm.

Jan 6, 1919

By Thomas T., Read

THE education of adolescents to perform the duties and assume the responsibilities of maturity has been a characteristic of human society since the dawn of history. In the beginning the members of the immediate family performed this function, and in modern life they still have an important part in it. Possibly religion was the first field in which education began to be functional; young people were sent for instruction to a teacher who had a broader and deeper knowledge of the subject than was possessed by the family. It does not seem necessary for our purpose to attempt to determine how, when, or where instruction in the practical arts first&apos; began to become functional, and the brief outline which follows must suffice. The discovery and utilization of mineral substances to improve and maintain the conditions of human living is a practical art, which must have had an almost accidental origin and have been developed by empirical experiments. We do not know, nor would it be useful to try to fancy, how men first learned that they could make use .of mineral substances to their benefit, but how- ever that knowledge was initially gained it was certainly trans mitted through instruction in the family. At first such activities must have been merely a .minor part of the making of a-living, but in time those who excelled found it better to devote them-

Jan 1, 1941

By S. A. Bradford

Internal-oxide precipitates in decarburized a iron alloys were studied by microscopic and X-ray methods. Diffusion of oxygen is primarily trans-granular, although large amounts of manganese or PhosPhorus cause preferred grain boundary dimsion at temperatures below 1450OF. Transgvanular internal oxidation follows the parabolic rate law with an apparent activation energy of 60 kcal per g-atom for decarburized rimmed steel and around 50 kcal per g-atom for higher alloy contents. The internal oxide is (Fe,Mn)0. Evidence was found for a miscibility gap in the FeO-MnO system. UNTIL very recently, the internal oxidation of metals was studied primarily as a scientific curiosity or, in a few cases, as a means of strengthening alloys by precipitation hardening. However, with the recent development of low-carbon enameling sheet steel, internal oxidation has become a problem of practical importance to the steel industry. For example, in 1961 it was reported1 that internal oxidation of steel can occur during decar-burization by open-coil annealing and will reduce the notch ductility of the sheet unless the process is carefully controlled. The present study was therefore undertaken to learn more about the rates and mechanism of oxygen diffusion and oxide formation in iron alloys. BACKGROUND The process of internal oxidation has been well-defined in the literature:&apos;,&apos; oxygen dissolves in an alloy, diffuses inward from the surface of the metal, and reacts to form a precipitate with the alloying element that will provide the most stable oxide. he growth of the finely divided so-called subscale, i.e., the internal-oxidation zone, depends on the diffusion rates of both the oxygen and the reactive element.4 Investigators have generally found that increasing the temperature increases the size of the oxide particles, the rate of subscale growth, and the tendency to transgranular diffusion. With very few exceptions, the square of the thickness of the internal oxide layer is directly proportional to the reaction time. Given two conditions easily satisfied for iron systems— a) an oxygen solubility much less than the concentration of the alloying metal and b) an oxygen-diffusion rate to the oxide boundary much faster than that of the alloying element—then the general expression developed by Rhines and co-workers5 for the parabolic growth rate of the internal-oxide zone can be simplified to the following form: where Co and CM are, respectively, the solubility of oxygen and the concentration of the alloying element, DO is the diffusion coefficient of oxygen, O/M is the weight ratio of oxygen to metal in the precipitated oxide, and x is the thickness of the internal-oxide zone after an annealing time t. Both the oxygen solubility and diffusion coefficient can be approximately expressed as functions of temperature by Arrhenius-type equations: in which H and Q are, respectively, the heat of solution and the activation energy of diffusion. Consequently, the apparent activation energies calculated from Arrhenius plots are the sum of the heat of solution of oxygen in iron and the activation energy for diffusion of oxygen. The data, if not the interpretation, of Schenck et al.8 bear out the fact that oxygen diffuses in the atomic form. The general rate law for atomic diffusion is: the reaction rate being proportional to the square root of the pressure at low pressures. Benard and Moreau8 studied both the surface oxidation of Fe-Ni alloys and the gradual penetration of oxygen into the metal. They observed that oxide particles first form along grain boundaries and then grow to form continuous films that eventually envelop the grains. The parabolic rate law does not usually apply in these cases, especially at the higher temperatures. The oxide formed is wustite which gradually transforms into Fe3O4 and finally into Kennedy and coauthors8 examined Fe-Ni alloys with 26, 75, and 84 pct Ni oxidized at 800°C and

Jan 1, 1964

By J. H. Henderson, L. A. Wilson, R. L. Gergins, R. J. Wygal, D. W. Reed

This paper presents a method of predicting the production history of an underground combustion recovery process. A rigorous solution of the thermodynamics and hydrodynamics involved is beyond the scope of this report. However, a practical scheme to appraise combustion recovery performance has been Worked out. By prudent assumptions, regarding the attainment of steady-state conditions, a trial-and-error solution, which satisfies both material balance and three-phase relative permeability requirements has been evolved and tested. As a combustion zone moves through a formation the interstitial water, the water of combustion and a portion of the oil wil1 be vaporized. These vapors will move downstream to a cooler region of the formation where they will condense. Part of the remaining oil will be displaced by the imposed gas drive and what remains behind will be consumed as fuel. The fluids will distribute themselves downstrean? in a manner which will satisfy the three-phase relative permeability characteristics of the formation. Three distinct zones will exist ahead of the combustion zone: (I) a zone termed a water bank which contains three mobile phases, oil, water and gas; (2) a region containing two mobile phases, oil and gas, called the oil bank; and (3) a zone having the fluid saturution distribution which existed prior to combustion. The mobile water will impose a water flood on the oil in the region containing three flowing phases. The process can be visualized as a simultaneous water .flood and combustion-supported gas drive. It is possible to estimate the saturation distributions in the water bank and oil bank as well as the production history for any combustion temperuture if the porosity, three-phase relative permeability characteristics, oil viscosity and initial saturations are known. This has been done for injection pressures ranging from I to 100 atm, oil viscosities of 10 to 1,000 cp and porosities from 20 to 40 per cent. Several of these calculations have been checked in the laboratory, with the result indicating rather good agreement between the predicted and observed production histories. The analytical and experimental techniques are described and the comparison of predicted and observed performance presented. INTRODUCTION Considerable research by the oil industry during the past 10 years has been directed toward the thermal recovery of crude oil. Of all schemes considered, the one receiving the most attention is in situ combustion. This is a process in which part of the oil is actually burned within the reservoir rock. The uniqueness of the process lies in its potential. Theoretically, this potential generates from the following: (1) it may open the door to vast reserves previously not economically producible, (2) it may induce increased production rates where low rates are now realized and (3) it may give high over-all recovery efficiency. The general idea of the process has received considerable attention in the literature &apos;-&apos; and the following brief description is intended for orientation only. In situ combustion can be visualized by considering a linear system, one end of which represents the injection well and the other the producing well. The formation at the inlet end is raised to ignition temperature by placing a gas or electric heater at the face of the formation or by the ignition of thermite, charcoal or similar material. While heating, the water and part of the oil in the heated region is vaporized and moved out into the reservoir by the injection of gas containing oxygen. In addition, part of the oil is displaced as liquid by the imposed gas drive. The oil not displaced is modified to an immobile, coke-like material (hereafter referred to as coke) by the high temperatures existing immediately ahead of the combustion zone. This coke is used as fuel, and the combustion front advances through the formation at a temperature which is probably in excess of 800°F. As the combustion front advancek it will drive ahead all interstitial oil not rendered immobile and all interstitial water plus the water formed by the combustion of hydrogen. As a result the sand behind the combustion zone is freed of all oil and water. Although the general description of the process has been outlined in the literature, there has been no consideration of the behavior of the fluids moving downstream from the combustion front. It is the purpose of this paper to present a technique

By H. I. Aaronson, C. Laird

Although the past results of X-ray experiments indicate that the broad faces of 0&apos; plates are coherent with their matrix, dislocations lying in arrays have frequently been observed at these boundaries by transmission electron microscopy. Critical experiments employing the latter technique have been carried out in order to determine the origin of these dislocations. It is concluded that 8&apos; plates are essentially coherent with the matrix at their broad faces throughout the aging temperature/time envelope studied. Virtually all of the dislocation arrays observed are deduced to have been formed by plastic deformation accompanying transformation. The proportion of dislocations arising from convexity of the plates is shown to be negligible by comparison with that from plastic deformation. At the higher aging temperatures, a[001] dislocations appeared in moderate numbers. These dislocations were traced directly, however, to the ledgewise dissolution of 0&apos; occasioned by the formation nearby of 0 crystals. On the other hand, since there is a parametric difference normal to the broad faces of the ?&apos; plates, mismatch dislocations do form at their edges. A previous conclusion that these dislocations have Burgers vectors of type a[001] was confirmed directly. The edges of 0&apos; plates were observed to develop octagonal shapes when growing, but circular shapes during dissolution. 1 HIS paper presents the results of an investigation of the interfacial structures of plates of the transitional phase, 8&apos;, formed in an A1-4 pct Cu alloy. In a companion paper, Part 11, the effects of these structures upon the migration kinetics of a:?f boundaries are reported. This work is pa.rt of a general program designed to establish the basis of precipitate morphology. The present authors in Al-Ag,1 and whitton2 previously in U-C alloys, have used transmission electron microscopy to examine directly the vander Merwe3-6 networks of dislocations anticipated7 to compensate the small amount of lattice misfit normally founda at the broad faces of Widmanstatten plates. Since the broad faces of 0&apos; plates are considered to be perfectly coherent with the corresponding habit planes in the a matrix,&apos; no dislocations should be present at these faces. Many reports have been published, however, giving evidence to the contrary.10-18 The primary objective of this investigation was therefore to ascertain the nature of these dislocation structures. An attempt to do this is described in the first three sections of this paper. Inspection of the matching of the a and 8 &apos; lattices at the orientations of the 0:0&apos; boundary corresponding to the edges of 0&apos; plates raises the possibility that these edges may be made up of rather closely spaced edge- type misfit dislocations oriented so as to be sessile with respect to the lengthening or shortening of the plates. Since this structure should severely inhibit migration of the plate edges (Ref. 7, Part II), a situation not originally anticipated,&apos; an experimental determination of the interfacial structure of the edges of 8&apos; plates was clearly in order, and is reported in Section III. Those aspects of the experimental procedure applicable to both Parts I and I1 are presented in the next section. Specific procedures applicable to individual aspects of each investigation, and also the relevant surveys of the literature, are then individually reported in the appropriate sections. I) GENERAL EXPERIMENTAL PROCEDURE The material used in both parts of these studies was the same as that of a previous investigation:" strips of A1-3.93 pct Cu, 0.009 in. thick, prepared as before, solution-annealed at 548°C for 6 hr, and quenched. Details of subsequent aging, and in some cases deformation treatments, are given in the Experimental Procedure sections of the individual parts of both papers. Specimens of the heat-treated strips were electro-thinned as beforeLg and examined in a Philips EM 200 microscope equipped with a goniometer stage. A commercial hot stage, of the grid-heater type and capable of * 30-deg tilt about one axis in the plane of the specimen, was also used for kinetic studies. The usual precaution of calibrating for the additional heat supplied by the electron beam was taken.19 A 16-mm cine cam-I era mounted outside the viewing window was frequently used to record the transformations. Conventional selected-area diffraction and dark-field viewing techniques were used to identify the precipitates in the foils. Normal bright-field images corresponding to two-beam diffracting conditions or dark-field images were employed to characterize the dislocations observed at the interfaces of the precipitates. The application of these techniques to the study of an interphase boundary, and the interpretation of the images,20&apos;21 has been fully described in a previous paper.&apos;

Jan 1, 1969

By Hugh Neill, O&apos

In previous papers,&apos; the author has reported the results of experiments on the straining in tension of a single-crystal test piece, about 0.6 in. long, of vacuum-melted electrolytic iron containing 1.8 per cent. of silicon. The crystal was originally in the "as cast" condition, and was stressed slowly along a tetragonal axis so that slipping along conjugate gliding planes finally transformed the original cylindrical portion into a pair of fracture wedges. One of these fracture wedges was sectioned along the stress axis in a plane at right angles to the edge of the wedge. A metallographic study of this plane of section led to the conclusion that slip had taken place in the (111) direction along (112) planes making a V shape with the stress axis. The present paper describes the results of scratch-hardness tests conducted on the same section, in order to determine the distribution of strain hardness therein, followed by annealing, and considers the resulting variations in hardness. These observations supplement those made by Krivobok2 on similar material reduced 25 per cent. by hammering (i. e., by impact) in the cold. In order to investigate ageing effects, two small crystals of the same alloy were also tested. The Specimens Employed The principal specimen, A, was prepared for the metallographic examination leading to the determination of the slip planes of the crystal. Therefore the work described in this paper was conducted on metal which had been repeatedly etched and had been allowed to rest for about 30 months after straining. It consisted of a section of the fracture wedge and contiguous unstrained head of the test piece taken along a tetragonal axis parallel to the direction of stressing, the plane of section originally being not far removed from the (011). Several subsequent grindings

GEO. F. COMSTOCK,* Niagara Falls, N. Y. (written discussion?).-This interesting paper throws additional light on a question about which differences of opinion have apparently existed in the past, and the writer would like to record in this connection the agreement of his experience with that of Primrose and Prof. Smart in regard to the effect of quenching on the properties of gun-metal bronze. The writer&apos;s results have been published, so that there is no need for a detailed report, here, but his in-vestigations resulted in showing that both gun metal and manganese bronze are ruined by quenching in water from a red heat, apparently because they cannot stand the strains produced by the sudden cooling. The lines, mentioned by Prof. Smart, in a polished and etched section of the quenched metal have also been noticed by the writer, who however has not found them any different in quenched specimens than in annealed specimens. Since they appear only after etching, it would seem most probable that they are merely grain boundaries in most cases, though Prof. Smart&apos;s idea that they are indications of strains is by no means impossible. Fig. 1 shows how these lines appeared on the author&apos;s speci-mens of annealed gun metal, etched with ammonia and hydrogen per-oxide, and magnified 100 diameters.

Jan 11, 1919

By M. J. Pearse

The processing of fine particles inevitably produces slimes. These present a dewatering problem, for which gravity thickening provides a partial or preliminary solution. The paper shows the effects of practical factors in carrying out laboratory sizing tests for thickeners. Several methods of determining thickener unit area have been compared for a lightly coagulated phosphate slurry and a highly flocculated kaolin slurry. Practical techniques of mixing and flocculant addition have significant effects on batch settling data. Pulp temperature and cylinder dimensions are very important. Errors in sizing thickeners for highly flocculated slurries by the standard methods are discussed. Such methods are suitable for less compressible slurries, however. Rules of thumb for flocculant selection are given.

Jan 1, 1980

By D. G. Westlake, E. S. Fisher

The habit planes for zirconium hydride precipitation in crystals of a zirconium have been determined at various hydrogen concentrations. The (10 • 0)planes are the predominant habit planes; some (10 • 5) and (10 -1) planes were observed after charging conditions which pevmitted formation of a surface layer of hydride. No platelets zrlere observed parallel to any of the twinning planes. Mechanisms for em-brittlement due to hydride precipitation are discussed. LANGERON and Lehr1 found, in 1956, that zirconium hydride precipitates in zirconium in platelets lying parallel to (10.0) slip planes. In 1960, Kunz and Bibbz reported observing the platelets in three different families of twinning planes, (10.2) {11.1), and {11.2), but never in the slip planes. The present study was undertaken to ascertain the cause of these seemingly contradictory results. EXPERIMENTAL Two specimens of iodide zirconium were used in the experiments. Specimen I was a single crystal, while specimen II contained three grains. Grain growth was accomplished by the technique of Lange-ron and Lehr. Three faces were ground on specimen I; the first was 2 deg from the (00.1) basal plane, a second was 2 deg from the (10.0) prism plane, and a third was 4 deg from the (12.0) plane. One face was ground on specimen II such that the poles of the surfaces of crystals A, B, and C were as shown in Fig. 1. After the faces were ground on 600 grit silicon carbide paper, they were chemically polished by dipping in a solution of 8 parts hydrofluoric acid, 50 parts nitric acid, and 50 parts water. This removed all cold worked metal from the surface. The samples were charged to various levels of hydrogen content by heating in hydrogen gas which had been purified by reaction with uranium powder. The various charging conditions are shown in Table I. Specimen I was heated to the reaction temperature at the indicated hydrogen pressure and allowed to react until essentially all the hydrogen was used up. Then the temperature was raised for homogenization. Specimen II was charged by making periodic addi-

Jan 1, 1962

By W. V. Green

The creep-rupture behavior of commercial powder-metallurgy tungsten rod is reported for temperatures of 2250°, 2500°, 2700°, and 2800°C, stresses up to 7000 psi, and times up to 4 hr. The temperature dependence and the stress dependence of creep rates are evaluated. Rupture time is fitted to the Larson-Miller parameter and compared to lower-temperature and higher stress results reported by pugh.4 THE tensile strength of single-crystal wire1 and of polycrystalline wire2 have been measured by Goucher. More recently Bechtold3 and pugh4 have studied the mechanical properties of tungsten rod between room temperature and 1200°C. Since tungsten has the highest melting point of all metals, it should retain useful strength to very high temperatures, and should find many applications in missiles, rockets, and so forth. Therefore, the mechanical usefulness of polycrystalline tungsten rod was investigated in the 2250" to 2800°C temperature range by short-time creep-rupture tests. MATERIALS TESTED Creep specimens were machined from 1/2-in. round commercial tungsten rod which was manufactured from powder by cold pressing, sintering, and hot swaging. Purity reported by the vendor was 99.95 pct W. Spectrochemical analyses showed "traces" (less than 0.01 pct) of silicon, iron, and titanium, and "faint traces" (less than 0.001 pct) of calcium and manganese. Carbon content was 30 ppm and nitrogen content was 70 to 110 ppm. No oxygen analysis was obtained. Room-temperature stress-strain tests on the as-received tungsten gave badly scattered results. Threaded end specimens broke at the threads. When these specimens were retested using shoulder grips, the specimens broke at the shoulders. No fractures occurred in the gage lengths. The fracture stresses were: 127,000; 137,000; and 154,000 psi for three specimens which fractured at the shoulders. The microstructure of the as-received tungsten rod is shown in Fig. 1. SPECIMENS USED Fig. 2 shows the two types of creep specimens tested. The threaded-end type specimen, which was used in most tests, had a 3/4-in. gage length and 1/4-in. gage diam. The cone-end specimen, which was used primarily to investigate the effects of a smaller gage diameter and the practicability of the modified grips and specimen, had a 3/4-in. gage length and a 1/8-in. gage diam. In both cases, the gage length terminated at 0.005-in. high shoulders which served as fiducial marks for optical strain measurements. Surface finish on the gage length was 16 µ-in. rms. Creep rates and rupture times were not significantly different for the two types of specimens and were not affected by electropolishing the specimens before testing. TESTING PROCEDURE The constant-load creep-testing machine used has been described by Smith, Olson, and Brown.5 In it the specimen is held vertically by grips of similar material and on the axis of a cylindrical tungsten or tantalum heater-tube. The specimen is loaded by means of the specimen grips, a pull rod (which is sealed to the chamber lid by a vacuum-tight bellows), a mechanical lever system, and hanging dead weights. Both specimen and grips are heated by radiation from the heater-tube, which is heated by its own electrical resistance. An optical system views the incandescent specimen through slits in the radiation shielding and heater-tube. The optical system projects an enlarged image of the specimen gage length on a ground-glass screen. Periodic gage-length measurements are made on this image with two cathetometers. Thorium oxide coatings on the specimen threads or conical end surfaces completely prevented diffusion-welding of specimens to grips, and were used

Jan 1, 1960

By E. R. Buchanan, R. E. Reed-Hill, F. W. Caldwell

Poly crystalline zirconium tensile specimens containing a sizable fraction of grains unfavorably oriented for slip were deformed at 77°K to strains as high as 9 pct. The contributions of the various twinning modes to the observed strain were deter~nlned quantitatively using measured twin volume fractions and Schrnid orientation factors. The results indicate that at very small strains twinning can account for almost all of the observed strain. At higher strains slip becomes the dominant means of deformation. The most significant form of twinning was {1121}. PLASTIC deformation in polycrystalline aggregates is poorly understood even today. This is primarily because slip cannot be easily observed or studied in the interior of a metal. On the other hand, twinning can be discerned inside a specimen after deformation. Twinning studies can therefore often yield quantitative information about polycrystalline deformation not otherwise obtainable. This investigation uses the above aspect of twinning in determining the contributions of twinning to the strain during tensile deformation at a cryogenic temperature (77°K). Polycrystalline zirconium was used as the object of study. There are several reasons why this information should be of value. In contrast to many metals, both the strength and ductility of zirconium increase with a corresponding decrease in temperature. This may be related to the fact that twinning becomes more profuse and complex with decreasing temperature. Secondly, it has been discovered that certain room-temperature properties of zirconium can be greatly improved by about 1 pct prestrain at 77°K. These include an increase in tensile elongation in critical directions by over 50 pctl and a large mechanical hysteresis effect.2 Both effects are believed to be related to twins formed by prestraining: plastic twin-boundary movements accounting for the increased ductility, and anelastic twin-boundary movements for the internal friction. Thirdly, hexagonal metals which twin primarily on only the (1012) mode (such as beryllium, zinc, and magnesium), unlike zirconium, are very limited in ductility at cryogenic temperatures. Therefore, the significance of the various types of twinning in zirconium at cryogenic temperatures is of more than academic interest. Three twinning mechanism-s have beenobserved in quantity at WOK, {1012), {1121), and {1122). Each must be considered as a unique deformation mechanism because of their markedly different twinning shears and basically different angles between twinning and basal planes, as shown in Table I. It is therefore necessary to separately consider the role of each of these twins during plastic deformation at 77°K. Fortunately, each twin possesses unique morphological features which makes its identification possible on a properly prepared metallographic section. The use of the polarized microscope3 can also greatly aid in identification of the various forms of twins. EXPERIMENTAL PROCEDURE Arc-melted sponge zirconium plate, previously describedY4 was machined into 1/8 by 1 1/4 in. threaded-end, round tensile test specimens. These specimens were deformed to the desired strains in a liquid-nitrogen cryostat mounted in an Instron testing machine. The tensile axis was the transverse plate direction. This specimen direction resulted in large numbers of grains in orientations unfavorable for deformation by prism or basal slip. Deformed specimens were sectioned, mounted in epoxy cold-mount resin, ground on metallographic papers, electropolished, and anodized to provide surfaces sensitive to polarized light. Standard quantitative metallographic procedures5

Jan 1, 1965

By R. I. Jaffee, F. C. Holden, H. R. Ogden

The effects of grain size and shape on alloys of titanium with nitrogen and aluminum have been determined. Increasing a grain size decreases strength and hardness and increases impact resistance. Quenching from the ß field produces subgrain markings delineating a plates in Ti-N alloys but not in Ti-AI alloys. This suggests a precipitation from the high nitrogen alloys. ALPHA titanium alloys are single-phase alloys with the hexagonal-close-packed structure of a titanium. If these alloys are worked and annealed within the a field, equiaxed structures result in which strength is derived from the solid solution of the alloying elements present. Strain hardening can be used to increase further the strength of a titanium alloys. This is the only other mode of strengthening the a type of alloy. Quenching from the ß field has been noted by many investigators to have little effect on the strength of iodide titanium and on commercial titanium. Ti-A1 alloys were found to be little different in hardness, whether annealed in the a field or quenched from the ß field.&apos; These facts illustrate a characteristic of a titanium alloys: they are insensitive to heat treatments from the ß field. Underlying this heat-treatment insensitivity are the facts that the a-ß field is generally narrow in a titanium alloys, the transformation-temperature range increases with a-stabilizing content, and the a solubilities of the alloying elements are greater than the ß solubilities. When quenching is done from the ß field, there is no supersaturation of the alloying elements in the acicular transformation structure produced. Welds in a titanium alloys generally are ductile, because no transformation hardening occurs during cooling.1,2 Other desirable features of a alloys are: no thermal-stability problem, excellent toughness, and retention of strength at elevated temperatures better than a-ß or ß alloys of comparable room-temperature strength. The prime factors governing the properties of a titanium alloys are the amount and kind of solute present. This can change the a phase from a soft, tough material into a hard, brittle material with no apparent change in microstructure. Moreover, brit-tleness can exist over a wider alloy-content range, without change of phase, than in most other metals. The solutes for a titanium may be divided into interstitial and substitutional types. Oxygen and nitrogen dissolve interstitially in rather large amounts, extending well through the brittle range, and the transformation-temverature ranges are raised in the process.:&apos; , carbon has a maximum interstitial solubility of about 0.5 pct at the peritectoid temperature, while at lower temperatures the solubility decreases to about 0.2 pct.3,5 Substitutional a solutes include aluminum and tin. Aluminum has a high a solubility of 25 pct Al, and increases the transformation-temperature range markedly.6,7 Tin has a high a solubility of about 20 pct, but has a relatively innocuous effect on the transformation-temperature range.&apos; The choice between interstitial and substitutional solutes generally has been conceded to the substitutional solutes because of a belief that they do not have as adverse an effect on ductility and notch toughness. However, a recent investigation8 on the effect of hydrogen on titanium has shown that this element, which is not under compositional control, has a powerful detrimental effect on notch toughness. Hydrogen was shown to form a hydride which is practically insoluble (about 0.002 pct) in a titanium at room temperature, although the solubility at the eutectoid temperature of about 300°C is relatively high, about 0.16 pct. Limited data were presented on the effect of hydrogen on a alloys, where the same impairment of toughness as in unalloyed titanium is found. The work reported here describes the effects of interstitial and substitutional solutes on 1—the mechanical properties of high purity titanium free of titanium hydride and 2—the influence of structural variables on these properties. Nitrogen was selected as an example of an interstitial solute with high solubility and aluminum as a substitutional solute with high solubility. All compositions were well within the ductile range, since it was not intended to study the brittleness problem here, but to study only the factors influencing optimum mechanical properties. Procedures The alloys were prepared from iodide titanium as 1/2 Ib ingots double melted to insure homogeneity.

Jan 1, 1955

By AIME AIME

SOME 65 members of the Institute, including most of the Local Section delegates and several Directors and officers, were on hand for the Annual Business Meeting of the Institute held in the Engineering Societies Building on Monday, Feb. 21, at 4:30 p.m., immediately following the second session of the Local Section Delegates Conference. President Mathewson presided. The meeting was largely taken up with the presentation of committee re- ports, discussion of which was invited. F. E. Wormser presented the report of the Admissions Committee ; Philip Kraft, Papers and Publications Com-

Jan 1, 1944

By W. A. Backofen, G. Y. Chin, W. F. Hosford

The ductile fracturing process was studied in single-crystal and poly cvystalline aluminum deformed in tension over a temperature range from 295° to 4.2°K. At temperatures as low as 77°K, the fracture of "inclusion-free" material, including zone-refined aluminum, was by rupture (-100 pct RA). At 4.2 OK, fracture was brought on by adia-batic shear. Metallographic examination did not disclose any voids or slip-band microcracks, thus negating for inherently ductile metals any mechanism of void nucleation by vacancy condensation or of cracking due to dislocation pile-ups. In Izigh-purity aluminum not treated to be inclusion-free, fracture at temperatures as low as 45°K was of the double-cup type and a result of void formation. The reduction-of-area decreased as temperature was lowered, corresponding to the earlier appearance of voids. Such behavior was rationalized in terms of a larger increase, with decreasing temperature, in the .flow stress relative to the strength of the inclusion-matrix interface. Evidence for low-temperature adiabatic shear was found in discontinuous flow at 4.2"K, in the transition to a localized shear fracture at low temperatures, and in the suppression of shear fracture with an elastically hard pulling device. A simple analysis for the initiation of adiabatic shew permitted a general correlation of the various contributing factors. It has been pointed out that the duration of shear depends upon effective mass and elastic stiffness of the deformation system. IT has long been recognized that fracture* may Throughout this paper, the term "fracture" is taken to mean any process that results in the separation of a material into two (or more) parts. Thus rupture as it may be encountered in a tension test leading to 100 pct reduction-of-area is included in this category. occur in a ductile mode, and that the process can be of great practical as well as general interest. Much information about ductile fracture has also been accumulated over this period, but only recently has an understanding of mechanism begun to appear. Ludwik,&apos; in 1926, first reported fracture in a tensile specimen starting with a central crack in the necked section. Since then, other studies have disclosed that such cracks may form by the coalescence of voids nucleated in this region where hydrostatic tension is highest.2-4 Rogers and Crussard et al.&apos; have emphasized void formation and reori-entation along localized shear bands as a mode of crack propagation. pines6 has considered the tensile rod as a bundle of fibers joined by weak interfaces, which subsequently separate to allow individual fiber contraction. The notion of cavity growth and coalescence by purely plastic processes was discussed by Cottrell: who added that the tensile reduction-of-area ought not to be sensitive to temperature. On the other hand, it has been observed that the reduction-of-area is greatly increased if tests are carried out at high temperaturesa or under high hydrostatic pressure.&apos; Fracturing anisotropy in wrought products lends support to the idea of void formation from preexisting flaws strongly aligned by earlier processing.&apos;&apos;-l2 There is evidence that many voids result from the fracturing of inclusions or separation at the inclusion-matrix interface Another possibility is that voids grow out of pore volume produced in the initial solidification and never fully removed in later working. In general, a structure 3f particles, pores, and weak interfaces can be expected, at least in materials of engineering interest. Vacancy condensation has been suggested as an alternative mechanism of void formation for materials considered to be inclusion-free.13 Yet experience has shown that tensile reduction-of-area increases with purity, to the extreme of rupture as so often observed in single crystals. Adiabatic shear has an important bearing on ductile fracture. It occurs when the decrease of flow stress, as a result of local temperature rise from heat generated during straining, becomes larger than the increase due to strain and strain-rate hardening. As demonstrated by experiments on punching of plates,14 a large temperature rise may be brought about by rapid straining. Adiabatic flow as a result of the high strain rate reached in an ordinary tensile specimen just prior to separation may account for the cone formation in cup-and-cone fracture;14 evidence of such local heating has been presented.15 For geometrical reasons, however, pure sliding along the conical surfaces is unlikely, and separation under tensile forces is probably an important accompanying feature of the shear.7 In deformation processing operations, a high shear-strain rate may exist at boundaries between plas-

Jan 1, 1964