Search Documents

By R. E. Tate, L. J. Herman

We have had occasion to produce wire of Np-237 in small diameters for use in some chemical experiments. Since the mechanical metallurgy of neptunium has not been investigated extensively, it seems desirable to report our successful extrusion technique. Because of the neptunium activity and its attendant health hazard the experimental work was done in glove boxes and related equipment also used for Pu-239. At room temperature a phase neptunium' is a hard (Dph -355) orthorhombic metal of high density (p = 20.45 g per cu cm). a neptunium transforms2 to tetragonal ß neptunium at about 280°C and this in turn transforms to bcc y neptunium at about 577°C. The y phase melts at about 637°C. A temperature of 340° to 345°C was selected for the extrusion, this temperature being a compromise be- tween a possible advantage of working with the presumably more plastic cubic y phase above 577°C and the risk of having the neptunium react with the alloy steel die to form the low-melting Fe-Np eutectic. A 0.75-in.-long, 0.26-in.-diameter ingot of good-purity* Np-237 was extruded by the direct *C = 230 ppm, Pu = 200 ppm, thirty-five metallic elements below limit of detection by spectrographic methods. process through flat-face orifices to form several sizes of wire ranging from 0.010 to 0.030 in. in diameter. Molybdenum disulfide was used as the die lubricant. The extrusion was done in a vacuum of about 10-4 torr to reduce reaction of the neptunium with atmospheric gases. British workers3 at Harwell have extruded neptunium under similar conditions. The force required to extrude 0.010-in.-diameter wire at the rate of 4 in. per min was 6000 lb, as measured with an electrical load cell. Wire 0.020 in. in diameter was extruded with a force of 4700 lb at a rate of 2 in. per min, and wire 0.030 in. in diameter was extruded with a force of 4000 lb at a rate of 1.3 in. per min. An extrusion constant, c, can be computed from the measured forces, P, for the equation4 P = c log-A/a where A/a is the extrusion ratio or the ratio of the cross-sectional areas of the container and the

Jan 1, 1965

By A. J. Opinsky

ThE superior performance of nonsag tungsten wire in lamps has been ascribed to the large-grained micro-structure that can be developed in it. The orientations of these large grains have been studied several times; most published data1-' appear to be similar to those plotted in Fig. 1. These new data were obtained by X-ray back-reflection Laue technique from all of the large grains occurring in thirteen different wires that had been heated at the lowest possible temperature for the formation of large grains. Here the wire axis is plotted in terms of the principal directions of the cube. Rosi decided that the preferred orientation of the large crystals could be described by a single ideal orientation, (531), being parallel to the wire axis.' Rieck2,3 and Mannerkoski' have essentially confirmed this finding. Opinsky, Orehotsky, and Seigle argued that the data suggest that (211) is parallel to the wire axis instead of a single ideal orientation.5 This {211} contains the (531) ideal orientation and would appear to be a more general case. Ahlborn and Wassermann report that their orientation data stretch from ( 110) through (531) to (311) 8 This is part of the locus of (211). All these investigators have determined the orientations of the large grains by back-reflection Laue techniques. They have all obtained essentially similar results. On the other hand, Swalin and Geisler, who obtained their data by neutron diffraction, indicated that the preferred orientation of the large grains in doped wire is (110) .7 These findings cannot presently be reconciled with the pole density data described in the previous paragraph. Rosi1 and Rieck2 have advanced arguments about how their orientations could occur. Nevertheless, the crystallographic link between the (110) (cold-worked) fiber texture and the preferred orientation of the large grains has remained missing. This link can be provided through the concept of coincidence-type boundaries. Such boundaries separate two grains that have a certain number of common lattice sites. Coincidence relationships that result from rotations about low index directions are given by Brandon et a1 .' What is desired is a calculation of those orientations that bear a coincidence relationship with the (110) fibers of the cold-worked matrix. This situation arises in the following fashion. Heating the tungsten wire for a combination of time and temperature falling short of the formation of the nonsag structure yields a structure that is still fibrous in nature and the preferred orientation remains (110). During grain growth, the growing grain is in contact with these fibers. It is hence possible that the entire process may begin by the passage of a coincidence boundary into a (110) fiber. The calculations were carried out analytically and checked graphically. Following Brandon et a1.,8 coincidence relationships from 1 in 5 to 1 in 19 have been considered. The results of the calculations are given in Fig. 2. Of the coincidences examined, some of those occurring upon rotation about ( 110) come closest to the experimental points in Fig. 1. Nineteen of the twenty-three data points in Fig. 1 can be attributed to the ideal orientations A, B, C, and D in Fig. 2. As determined analytically, three crystals lie within 4 deg of point A, four lie within 21/2 deg of point B, eleven lie within 5 deg of point C, and one lies within 1 deg of point D-a total of nineteen. The off-lying points are near the |110| point of the triangle.

Jan 1, 1968

By E. Miller, J. M. Eldridge, K. L. Komarek

Aclivilies of magnesium in liquid Alg-Si alloys have been delermined between 5 and 60 at. pcl Si, close to the melling point of Mg2Si, by an improved isopieslic melhod. Silicon specinrens, held in alumina crucibles and graplrile conlainevs of special design, were healed in a letrlpevalure gvadient and equilibrated with mag-nesilcrrl rapor in a closed lilanium system. The ther-madynamic Junctions were calculated and compared with the thermodyuamic properties of the other three mg- Gvoup IVB systems. Lattice paramelers of three Mg2X compounds were measured. The bonding in the Mg2X compounds is largely covalent with small and uarying amounts of metallic and ionic conlvibutions. The Mg-Si phase diagram1 has one congruent melting compound, Mg2Si, of essentially stoichiometric composition, two eutectics, and very limited terminal solid solubilities. Little information is available on the thermodynamic properties of this system. The free energy of formation of Mg2Si has been determined by the Knudsen cell technique2 in the range 572" to 680oC, by the transportation method3 between 858" and 950oC, and by the electromotive-force method4 in the range 400o to 600°C. Kubaschewski and villa5 and caulfield6 have measured the heat of formation of Mg2Si. An electromotive-force study of magnesium-rich liquid alloys was recently published by Sryvalin el al.7 The present investigation was undertaken to complete a general survey of the thermodynamic properties of the homologous series of Mg-Group IVB systems, i.e., Mg-Pb,a9,Mg-Sn,10,11 mg-Ge,12and Mg-Si. An isopiestic technique, previously developed for similar measurements on liquid Mg-sn11 and Mg-Ge alloys,12 was modified for the Mg-Si system. Specimens of the nonvolatile component, silicon, were contained in dense alumina crucibles placed inside covered graphite crucibles which were heated in a temperature gradient in an evacuated and sealed titanium reaction tube and equilibrated with magnesium vapor of known vapor pressure. The alumina crucibles prevented contact between the highly corrosive liquid Mg-Si alloys and graphite. The graphite cruci- bles effectively preserved the high-temperature equilibrium composition of the liquid alloys containing highly volatile magnesium on termination of the experiments during the quench to room temperature. EXPERIMENTAL PROCEDURE Silicon of semiconductor-grade purity (E. I. du Pont de Nemours and Co., Brevard, N.C.) and 99.99+ pct Mg (Dominion Magnesium Ltd., Toronto, Canada) were used. Graphite crucibles with press-fitted lids were machined from high-density (1.92 g per cu cm) rods (Basic Carbon Corp., Sanborn, N.Y.) which had a maximum ash content of less than 0.04 pct. The alumina crucibles had a purity of 99.7+ pct (Triangle RR grade, Morganite, Inc., Long Island City, N.Y.). In preliminary runs the liquid alloys were contained in graphite crucibles following the exact procedure developed for the Mg-Ge system.'2 These runs failed due to appreciable reaction between the molten Mg-Si alloys and graphite, and the results have been discarded. The procedure was then modified and the Mg-Si alloys were subsequently held in alumina crucibles. For most of the runs alumina crucibles of known weight and approximately 6.3 mm ID, 12.5 mm height, 1.0 mm wall thickness were loaded with weighed amounts of silicon and encapsuled in tightly covered weighed graphite crucibles 5/16 in. ID, 2 in. helght, 3/32 in. wall thickness). The graphite crucibles were machined from rods which were 85 pct of the theoretical density. These crucibles were therefore sufficiently porous so as to permit magnesium vapor to effuse through the silicon under the experimental conditions of approximately 970O to 1220°C and 1 day equilibration time. However, negligible magnesium was lost from the crucible during the quench due to the slow effusion rate through the pores of the graphite. The inner alumina crucible prevented the liquid alloys from contacting the graphite, and the very tightly fitting graphite crucible lids served to retain any magnesium vaporizing from the alloys inside the crucibles during the quenching step.12 The loaded silicon-alumina-graphite cells were positioned, one above another, on a 16-in.-long titanium thermocouple well and tied securely to the titanium tube with thin molybdenum wires held in grooves around the circumference of the graphite crucibles. A thin (0.005-in.) molybdenum strip prevented contact between the graphite crucibles and the titanium. This assembly was lowered into a titanium reaction tube (la in. ID, 16 in. long, $ in. wall thickness) closed on one end which contained a 11/2-in.-long cylinder of magnesium at the bottom. The inner titanium thermocouple well was positioned eccentrically in the large tube because of the eccentric mounting of the cells on the well. Appropriate modifications of the titanium cap"'12 were made to join the inner and outer titanium

Jan 1, 1968

By L. C. McCabe

THIS paper is a progress report on a study, of the distribution of the banded ingredients (Figs. 1 and 2) in- Illinois screenings and the method of determining their distribution. Proximate analyses and screen tests1 have been reported and a further report on the washability characteristics of the screenings is in preparation. The microscopic study of the screen-ings is not yet far enough advanced to permit a conclusive report on the effect of mining, screening and washing on the distribution of the banded ingredients in the coals of Illinois. However, considerable fundamental data-have been collected as a background for the screenings investigation and for a proposed study of fuels composed of known quantities of vitrain, clarain and fusain, the three common banded ingredients of Illinois coals. These fundamental data and the preliminary information now available from the microscopic study of screenings are broadly indicative of the reaction of the coals to the physical processes affecting them in mining and preparation. Proximate analyses of samples of vitrain, clarain, and fusain from several Illinois mines have been published 2, but those given in Table 1 serve to show the differences that are apparent in proximate analyses. The vitrain samples are consistently low in ash, and the unit-coal value is uniformly lower than in clarain. The average .fuel ratio (F.C./V.M.) of the vitrain samples in the table is 1.57-whereas the clarain average is 1.42. The fusain analyses vary considerably in ash and moisture. In the two samples from this mine the moisture values range from 8.99 to 22.80 and the ash from 4.86 to 16.91 per cent. Fusain has higher fixed carbon than either vitrain or clarain but the percentage is erratic from sample to sample.

Jan 1, 1936

By H. H. Power, Charles R. Houssiere

THE development of effective and dependable methods for drilling through the so-called "heaving-shale" horizons, particularly in the Gulf Coast area, is believed to comprise a major contribution to drilling technology, and to the task of finding and developing our undiscovered oil pools. Many mechanical remedies have been proposed and are in use in troublesome areas for combating heaving shale. However, in conducting a research program it was concluded that the physical and chemical properties of shales should be investigated, and the effect of added chemicals on such properties determined. As a preliminary step, the effect of chemicals on bentonitic suspensions was determined in accordance with recent contributions in the field of ceramics. The most plausible theoretical explanations for the behavior of the clay minerals involved are offered in the paper that follows. It is hoped that subsequent investigation of actual shale from troublesome wells will be aided by the initial work done on bentonitic suspensions of known composition. INTRODUCTION Formations variously designated as "heaving shale," "sloughing shale" and "caving shale" impede and may even preclude drilling of oil wells, particularly in certain parts of the Gulf Coast. In a previous paper1 it has been stated that the development of effective and dependable methods for drilling through these troublesome beds is believed to comprise a major contribution to drilling technology, and to the task of finding and developing our undiscovered oil pools. Since the attack on the heaving-shale problem by mechanical means was principally a matter of field investigation, it was concluded that a research program should be concerned with the physical and chemical properties of heaving shales, and the effect of added chemicals on such properties. It was realized that a study of shales required an advanced knowledge of the behavior of the individual clay minerals. A thorough review of the literature led the authors to the conclusion that very recent contributions2.3 in the field of ceramics furnished the most plausible theoretical explanations for the behavior of clay minerals. Accordingly, these fundamental ideas will be used in an attempt to explain the behavior of more complex systems whose composition and replaceable ions are known. In order to obtain comparable results it was deemed important to select an easily procurable clay of uniform characteristics. Accordingly, Wyoming bentonite, which is marketed under the name of "Volclay,"* was used for the preliminary investigations. The chemical analysis reported by the distribution is given as follows:

Jan 1, 1941

HENRY G. MARTIN,* Chicago Heights, 111. (written discussion?).-. The object in taking three or more ladle tests is to secure a sample that will show the average composition of the heat, not primarily to investigate the lack of uniformity existing; however, the assumption that the samples are not of uniform composition -remains. In other words, we have three samples of steel of different composition, the par-ticles of which are not subject to extreme comminution so as to mix inti-mately, and yield an average homogeneous sample, if placed in one

Jan 11, 1919

By Lyon F. Terry

INCREASING domestic demand for products, a sharp reduction in exports to Europe, and a rise in imports from South America were the chief features of the economic side of the industry in 1940. As the war progressed it became evident that exports to former European customers were being cut off or drastically reduced, leaving heavy inventories of products in the hands of many American refiners who had anticipated larger demands from the belligerents. Stocks of motor fuel reached burden-some proportions early in the year for the added reason that refining operations were stimulated by heavy demand for heating oils. Excessive tanker rates for Gulf to Eastern Seaboard movements during the first part of 1940 contributed to the accumulation of products on the Gulf Coast, where refinery gasoline prices were forced to extremely low levels by midyear. Tanker rates receded to normal during the summer but have since risen again to the approximate equivalent of pipe-line tariffs from the Mid-Continent.

Jan 1, 1941

The Mineral Industry, Published by McGraw-Hill Book Co, New York, N Y. The Mineral Industry is an annual review of the mineral industry It is a standard and complete reference on the mineral industry for the year covered Through the cooperation of the A I M E its publication in 1933 was made possible Mineral Industry for 1930 contains sections devoted to the production, consumption, trade, market, uses and technology of the following headings: Abrasives, aluminum and bauxite, antimony, arsenic, asbestos (b), asphalt, barium and strontium, chromium (b), coal and coke, cobalt (b), copper, diatomite, fluorspar, gold and silver, graphite, gypsum, iron and steel (b), lead, magnesite, manganese, mica, molybdenum, nickel, petroleum and petroleum products, phosphate rock (b), platinum group metals (b), potash, precious and semiprecious stones (b), quicksilver, radium (b), uranium and vanadium, slate (b), sodium salts, sulfur, pyrite, sulfuric acid, talc and soapstone, tin, titanium and zirconium, tungsten (b), zinc, minor metals, minor nonmetals, ore dressing and coal washing (b). Sections marked (b) have appended a bibliography of recent literature on the subject. Each section is written by an acknowledged expert. Other volumes contain similar material Prices -The Mineral Industry, 1892-1930, vols. 1 to 39. Complete sets of this work, uniformly bound, except vols 25 and 26,

Jan 1, 1933

By H. C. Chang, N. J. Grant

Creep of very coarse grained, high purity aluminum was studied at 400° to 1100°F with an initial stress range of 50 to 1200 psi. The process of boundary sliding and migration was studied. The driving force of boundary migration under creep conditions is shown to be a combination of strain energy migrationand surface energy. A theory is presented regarding the strainenergyrole the grain boundaries play under creep conditions. From this thetheory intercrystalline failure of commercial alloys can be explained. Also from this theory an optimum grain size should exist for good high temperature properties of high purity materials. IN the investigation of the creep of very coarse grained, high purity aluminum previously reported,' the cyclic nature of the process of grain boundary sliding and migration has been established by microscopic observation of the actual creep process as well as metallographically. It was also substantiated by measuring localized strains across the grain boundaries. In addition, it was shown how extensive subgrain and fold formation may result from boundary sliding and how the slid grain boundary may become sharply wavy as a result of subgrain formation. Since the publication of those results, additional information on the process of grain boundary sliding and migration has been obtained. It is the purpose of this paper to report on the direction and driving force of boundary sliding and migration, the effect of grain size, and the effect of temperature. Finally the effect of decreasing purity (alloys 2s and 3s) on the process of boundary sliding and migration is noted. From these results, an explanation is presented for the intercrystalline failure of alloys under creep conditions. The effects of grain size on the creep properties of impure and high purity materials are discussed in the same light. The experimental procedures and technique have been presented elsewhere.' It is only necessary to state how the 2s and 3s aluminum specimens are prepared. Machined specimens were first annealed at 600°F for about 12 hr. In order to produce a large grain size the specimens were then stretched 3 to 8 pct. The specimens were marked with reference marks, electropolished, annealed at 900°F for 24 hr and at 1150°F for 12 hr, and repolished. The grain size of 2s aluminum produced by this treatment is comparable to that of high purity aluminum in the direction of its width of the specimen, i.e., there are 2 to 4 grains across the width of the specimen. However, the grains of 2s aluminum are 3 to 10 times longer in the direction of the specimen axis. On the other hand, the grain size of coarse grained 3s aluminum ranges from 10 to 20 grains across the width of the specimen due to the treatment just outlined and therefore is much smaller than that of both high purity and 2s aluminum. As in 2s aluminum, the grains are about 3 to 10 times longer in the direction of the specimen axis than in the direction of the width of the specimen. The arrangements of the grains in 2s and 3s aluminum were generally irregular; therefore it was difficult to follow the course of the grain boundaries. Results Method of Presentation: In order to show the arrangement of the grains, especially the direction and positions of the grain boundaries, traces of the grain boundaries on the four surfaces of the specimens were unfolded and mapped out after macroetching. Figs. 1 and 2 show the structural development drawings of specimens P-3 and P-8 respectively. The two flat surfaces (of which the front one faces the microscope) and the round-edged surfaces will be called the "front surface" and "back surface" and

Jan 1, 1954

By Milton H. Fies

THE Alabama Power Co. operates its Gorgas mine in Walker County, Ala., immediately adjacent to its steam plant. The coal mine property consists of some 19,000 acres of fee and mineral ownership lands, and all of the production from the mine-approximately 2500 tons per day-is utilized at the company's adjoining steam plant. The company is presently considering the purchase of additional acreage adjoining its present holdings which acquisition will almost double its reserves. The coal is transported from the mine over a short railroad spur in the company's own equipment, either directly to one of the large plants at Gorgas or to a storage pile. The longest haul is about 1 1/4 miles.

Jan 12, 1950

By Carlton Beal

This paper presents useful charts for conversion of various viscosimeter units into centipoises and graphically summarizes published investigations of the viscosity of air, water and natural gas at high temperatures and pressures. Where possible, charts and correlations were constructed to cover a range of temperature (60°F. to 300°F.) and pressure (14.7 lb. per sq. in. abs. to 8000 lb. per sq. in. gauge) encountered in oil fields. Correlation charts, for the purpose of predicting crude oil viscosity and solubility behavior at oil field temperatures and pressures, were constructed from an analysis and correlation of 1332 viscosity and solubility observations from 953 crude oil samples taken from 747 oil fields. Of these fields, 501 are in the United States, including 75 in California. Of the 1332 observations, 1215 were viscosity values, including 786 of gas-free crude oil, 351 of oil saturated with gas, and 78 under-saturated with gas at pressures above the bubble point. Results show that crude oil viscosity at various reservoir conditions can be predicted with average deviations varying from 24.2 per cent for gas-free crude oil to as little as 2.7 per cent for undersaturated crude oil "above the bubble point." The solubility of crude oil may be predicted from oil gravity and saturation pressure with an average deviation of 22.0 per cent from observed values. In conclusion, it is shown that the viscosity of a gas and gas-saturated crude oil may be predicted within the accuracy of most reservoir computations. Viscosity is a measure of flow resistance; common units are in centipoises (cp.). The object of this report is to present conversion charts and simplified 'correlation charts showing the viscosity behavior of air, water, gas and crude oil and gas-saturated crude oil under oil field temperatures and pressures, which have been known to be as high as 300°F. and 8000 Ib. per sq. in. gauge under subsurface conditions. The viscosity of a liquid or gas is important because it is a measure of its fluidity, or its ability to flow through pipe lines or oil sands. Viscosity of air has become important because it is being used in secondaryl,2 recovery projects. The viscosity of natural gas and water at reservoir conditions is useful because they are almost universally associated and produced with crude oil. The viscosity of gas-saturated crude oil at reservoir pressures and tem peratures is of particular value in making estimates of oil reserves3 and rate of oil recovery from flush pools when production decline data are limited. Instruments Used to MeasuRe Viscosity There are many types of viscosimeters,4 and the instruments most commonly used to measure the atmospheric viscosity of liquids at moderate temperatures and their practical working ranges have been deScribed5,6 in detail. Fig. I and Fig. 2 are viscosity conversion charts which have

Jan 1, 1946

By Carlton Beal

This paper presents useful charts for conversion of various viscosimeter units into centipoises and graphically summarizes published investigations of the viscosity of air, water and natural gas at high temperatures and pressures. Where possible, charts and correlations were constructed to cover a range of temperature (60°F. to 300°F.) and pressure (14.7 lb. per sq. in. abs. to 8000 lb. per sq. in. gauge) encountered in oil fields. Correlation charts, for the purpose of predicting crude oil viscosity and solubility behavior at oil field temperatures and pressures, were constructed from an analysis and correlation of 1332 viscosity and solubility observations from 953 crude oil samples taken from 747 oil fields. Of these fields, 501 are in the United States, including 75 in California. Of the 1332 observations, 1215 were viscosity values, including 786 of gas-free crude oil, 351 of oil saturated with gas, and 78 under-saturated with gas at pressures above the bubble point. Results show that crude oil viscosity at various reservoir conditions can be predicted with average deviations varying from 24.2 per cent for gas-free crude oil to as little as 2.7 per cent for undersaturated crude oil "above the bubble point." The solubility of crude oil may be predicted from oil gravity and saturation pressure with an average deviation of 22.0 per cent from observed values. In conclusion, it is shown that the viscosity of a gas and gas-saturated crude oil may be predicted within the accuracy of most reservoir computations. Viscosity is a measure of flow resistance; common units are in centipoises (cp.). The object of this report is to present conversion charts and simplified 'correlation charts showing the viscosity behavior of air, water, gas and crude oil and gas-saturated crude oil under oil field temperatures and pressures, which have been known to be as high as 300°F. and 8000 Ib. per sq. in. gauge under subsurface conditions. The viscosity of a liquid or gas is important because it is a measure of its fluidity, or its ability to flow through pipe lines or oil sands. Viscosity of air has become important because it is being used in secondaryl,2 recovery projects. The viscosity of natural gas and water at reservoir conditions is useful because they are almost universally associated and produced with crude oil. The viscosity of gas-saturated crude oil at reservoir pressures and tem peratures is of particular value in making estimates of oil reserves3 and rate of oil recovery from flush pools when production decline data are limited. Instruments Used to MeasuRe Viscosity There are many types of viscosimeters,4 and the instruments most commonly used to measure the atmospheric viscosity of liquids at moderate temperatures and their practical working ranges have been deScribed5,6 in detail. Fig. I and Fig. 2 are viscosity conversion charts which have

Jan 1, 1946

By J. A. Herbst, J. L. Sepulveda, J. D. Miller

Abstract-Lead cake, a zinc smelter flue dust residue, consists primarily of lead sulfate. Characteristic properties of lead cake were determined in order to aid the understanding of reaction mechanisms involved in bismuth removal from lead cake by sulfuric acid digestion. Sp gr (specific gravity) measurements, surface area measurements, and photomicrographs revealed that the particles of lead cake are quite porous and seem to consist of an agglomeration of submicron grains (0.4 pm) fused together in a manner similar to cement clinker. Analysis of experimental rate data, which was independent of particle size, indicates that the dissolution reaction involves two distinct, rate limiting steps. The initial stage of reaction appears to be limited mainly by intergranular diffusion of the reactant, hydrogen ion, while the latter stage of reaction appears to be controlled by diffusion of soluble reaction products through the reaction product layer of the individual grains.

Jan 4, 1978

By D. V. Carter, F. M. Hackbusch

Beginning the year 1938, the East and East Central Texas district comprised 48 counties, which is equivalent to the Texas Railroad Commission districts 5 and 6. At the close of the year there were 46 oil and gas fields in this district. Eight other fields, seven oil and one gas, have been abandoned. Exploratory Drilling During the year, 113 exploratory wells were drilled. Nine discoveries were made, five of which proved to be oil fields, three distillate, and one gas. Completions for the district were 2043 oil wells (distillate wells included), 36 gas wells and 163 dry holes. Exclusive of the East Texas field, the Marion County extension of the Rodessa field led the district in the number of completions during the year. Production and Proration All fields in the district produced a total of 182,369,484 bbl. of oil, a decrease of 12.57 per cent compared with the 208,594,453 bbl. produced during 1937. The East Texas field produced 148,189,913 bbl., which was 81.6 per cent of the district's production for 1938. November daily average oil production for the East and East Central district was 469,102 bbl. The estimated cumulative production to Jan. 1, 1939, for this district was 1,753,894,802 bbl. It is estimated that the East and East Central district produced 38.9 per cent of the state's total production for the year, which was 468,781,632 barrels. The decrease in 1938 production, as compared to that of 1937, in this district was partly due to the Saturday and Sunday shutdowns, 71 days for the year, which is equivalent to 19.45 per cent of the year. All fields in this district were affected by shutdowns except the Texas portion of the Rodessa field, which was shut in only during January and February. Certain wells were exempt from these shutdowns because of special pro-

Jan 1, 1939

By D. V. Carter, F. M. Hackbusch

Beginning the year 1938, the East and East Central Texas district comprised 48 counties, which is equivalent to the Texas Railroad Commission districts 5 and 6. At the close of the year there were 46 oil and gas fields in this district. Eight other fields, seven oil and one gas, have been abandoned. Exploratory Drilling During the year, 113 exploratory wells were drilled. Nine discoveries were made, five of which proved to be oil fields, three distillate, and one gas. Completions for the district were 2043 oil wells (distillate wells included), 36 gas wells and 163 dry holes. Exclusive of the East Texas field, the Marion County extension of the Rodessa field led the district in the number of completions during the year. Production and Proration All fields in the district produced a total of 182,369,484 bbl. of oil, a decrease of 12.57 per cent compared with the 208,594,453 bbl. produced during 1937. The East Texas field produced 148,189,913 bbl., which was 81.6 per cent of the district's production for 1938. November daily average oil production for the East and East Central district was 469,102 bbl. The estimated cumulative production to Jan. 1, 1939, for this district was 1,753,894,802 bbl. It is estimated that the East and East Central district produced 38.9 per cent of the state's total production for the year, which was 468,781,632 barrels. The decrease in 1938 production, as compared to that of 1937, in this district was partly due to the Saturday and Sunday shutdowns, 71 days for the year, which is equivalent to 19.45 per cent of the year. All fields in this district were affected by shutdowns except the Texas portion of the Rodessa field, which was shut in only during January and February. Certain wells were exempt from these shutdowns because of special pro-

Jan 1, 1939

By Paul D. Merica, W. A. Mudge

ONE of the most prominent features of our present-day industrial development is the ever-increasing demand put upon materials of construction Engineering ingenuity, within the past 25 years, has been unusually active, and in some fields at least engineers frankly say that engineering design has progressed as far as the limitations imposed by the properties of the present materials of construction will permit. Consequently, they are today demanding improvement in their working materials and seeking new ones, through the aid of which the present limitations of design may be overcome The activity of this search is evident in all fields, but it is particularly so in that of structural materials required to be resistant to corrosion The corrosion resistance of metals and alloys is never absolute and all-inclusive, a particular alloy will withstand some corrosive conditions well and fall utterly under others Furthermore, other properties, physical and mechanical, required in conjunction with corrosion resistance vary considerably for different commercial applications One wants a soft, ductile sheet metal resistant to atmospheric corrosion, another, a high-strength alloy resistant to sulfuric acid The last decade has witnessed active and definite progress in the development of high-strength, corrosion-resisting alloys In June, 1924, a symposium by the American Society for Testing Materials, on Corrosion-Resistant, Heat-resistant and Electrical-resistance Alloys, disclosed no less. than 60 commercial alloys the properties of which were described as being suitable for industrial service where corrosion resistance

Jan 1, 1935

By Emma Smith, R. W. Guard

INVESTIGATION of the nickel-rich end of the Ni-Zr system has been prompted by an interest in the effect of small amounts of zirconium in high temperature alloys. Hansenl presents a hypothetical diagram based on the work of Allibone and Sykes,2 who investigated the system up to 44 atomic pct (55 wt pct) Zr by metallographic means. Since the alloys they used were melted in Alundum crucibles they were probably contaminated with appreciable amounts of aluminum. They found two compounds which they called Ni3Zr and Ni4Zr. Hayes, Roberson, and Paasche3 identified a compound NiZr (50 atomic pct Zr) with a melting point of 1470°C. Such a high melting compound is not compatible with the observation of Allibone and Sykes2 hat a eutectic is formed near 50 atomic pct. The alloys containing up to 60 atomic pct Zr were melted in an inert atmosphere in a noncon-sumable electrode arc furnace. Analysis of most of the alloys indicated negligible loss of zirconium. The alloys were examined in the as-cast condition and also after annealing for 6 hr at 1175°C (or 1000°C for the alloys between 25 atomic pct and 45 atomic pct). Metallographic specimens were etched using mixtures of HF-HNO3-H2O or acetic acid- HN0,-H,O. The specimens for the solidus determinations were wrapped in molybdenum foil and sealed in evacuated quartz tubes. Specimens to be heated above 1300°C were enclosed in zirconia tubes inside the quartz to prevent reaction with molybdenum. The solidus determinations were carried out by heating the specimens at various temperatures for a few minutes and then examining the interior structure metallographically to determine at what temperature melting began. The 150 mesh powders for X-ray analysis were annealed in an evacuated quartz tube for 2 hr at 540 °C to remove cold work. Alloys with 22.5 atomic pct Zr and 44.4 atomic pct Zr required annealing at 700 °C for complete recovery. The grains of both of these alloys were soft and rather ductile. Both Debye-Scherrer film patterns and spectrometer traces were made for each alloy using filtered copper radiation. Results and Discussion The presence of a substantial amount of second phase in an alloy with 1.1 atomic pct Zr indicated that the solid solubility of zirconium in nickel is somewhat less than 1 atomic pct. The a0 value for the face-centered-cubic matrix in the same alloy was equal to that of pure nickel, so that the solubility must be very small. This observation is as expected from the large atom size difference. Annealed specimens of alloys with 15.0, 16.7, 22.5, 28.6, 44.4, and 59.4 atomic pct Zr showed. micro-structures that were essentially single phase. When

Jan 1, 1958

By Victor Formanek, Paul Chataignon, Maurice Rey

IT is found when floating oxidized lead ores by sulphidization, that the presence of calcium salts in the water, is usually detrimental and lowers the recovery. This effect is particularly marked in dry countries such as North Africa, where the waters often carry large amounts of calcium sulphate and where the ore may even contain gypsum. The effect of calcium salts is readily visible. Whereas in their absence cerussite is quickly stained brown and then black by sodium sulphide, in their presence the mineral remains very light in color. A similar effect is produced when barium sulphide is used as a sulphidizing agent instead of sodium sulphide. Magnesium salts have little or no effect and even tend to reduce the detrimental effect of calcium salts. A study of this phenomenon indicates that it is due to the precipitation of calcium or barium carbonate in contact with the mineral simultaneously with the formation of lead sulphide. The chemical reactions can be interpreted as: PbCO3 + Na2S = PbS + Na2CO3 CaSO4 + Na2CO3 = CaCO3 + Na2 SO4 They might also be written: PbCO3 + S = + Ca++ = PbS + CaCO3 The precipitation of calcium carbonate can be followed by the lowering of the pH with which it is accompanied. Magnesium carbonate is more soluble than calcium carbonate and usually does not precipitate under the conditions prevailing. It is interesting to note that calcium salts have no effect on anglesite (lead sulphate) because calcium sulphate is soluble, but barium salts hinder the sulphidization of anglesite because of the precipitation of barium sulphate. Remedies When calcium sulphate is present in large amounts, the softening of the water with soda ash is usually too expensive to be considered, but the precipitation of the objectionable calcium carbonate can be prevented in two different ways. One is the use of sodium hydrosulphide instead of sodium sulphide. This salt gives a lower pH than sodium sulphide and does not bring about the immediate precipitation of the calcium which remains in solution as calcium bicarbonate. The other procedure is to add ammonium salts such as the sulphate or chloride which have the property of increasing markedly the solubility of calcium carbonate. Ammonium salts have other effects such as cutting down conditioning time and accelerating flotation. They should be added to the flotation cells rather than to the ball mills. Table I. Effect of Sodium Hydrosulphide and/or Ammonium Sulphate on the Flotation of Two Oxidized Lead Ores Mibladen Ore4 La Plagne Ored Con- Tall- Con- Tail-centrate ing centrate ing Reagents Pb, Pct Pb, Pct Pb, Pct Pb, Pot Without addition of CaSO, NaS 56.0 0.68 43.4 0.65 NaSH 56.2 0.60 40.4 0.50 Na2S + (NH4)2SO4d 54.6 0.56 NaSH + (NH4)2SO4d 43.0 0.66 With addition of 40 lb/ton CaSO4 Na2S 39.4 3.85 34.0 3.21 NaSH 49.1 0.70 49.6 0.88 Na2S + (NH4)2SO4d 53.9 0.85 NaSH + (NH4)2SO4d 51.0 0.45 41.1 0.78 In table I are given the results of representative tests on two different oxidized ores. They show that the strongly detrimental effects of calcium sulphate can be offset by the two procedures outlined above. Sodium hydrosulphide is now used regularly on a mill scale on certain ores. Tests are being carried out with ammonium salts. It should be noted that malachite is subject to influences similar to cerussite. One final word of caution—when the ore is rich in primary slime, which is flocculated by the calcium salts, it may be indispensable to remove these by washing or precipitation with sodium carbonate instead of keeping them in solution by the above methods. Acknowledgment We wish to thank Socibtk Miniere & Metallurgique de Penarroya and Minerais et Metaux, for permission to publish these results.

Jan 1, 1951

By Maurice Rey, Victor Formanek, Paul Chataignon

IT is found when floating oxidized lead ores by sulphidization, that the presence of calcium salts in the water, is usually detrimental and lowers the recovery. This effect is particularly marked in dry countries such as North Africa, where the waters often carry large amounts of calcium sulphate and where the ore may even contain gypsum. The effect of calcium salts is readily visible. Whereas in their absence cerussite is quickly stained brown and then black by sodium sulphide, in their presence the mineral remains very light in color. A similar effect is produced when barium sulphide is used as a sulphidizing agent instead of sodium sulphide. Magnesium salts have little or no effect and even tend to reduce the detrimental effect of calcium salts. A study of this phenomenon indicates that it is due to the precipitation of calcium or barium carbonate in contact with the mineral simultaneously with the formation of lead sulphide. The chemical reactions can be interpreted as: PbCO3 + Na2S = PbS + Na2CO3 CaSO4 + Na2CO3 = CaCO3 + Na2 SO4 They might also be written: PbCO3 + S = + Ca++ = PbS + CaCO3 The precipitation of calcium carbonate can be followed by the lowering of the pH with which it is accompanied. Magnesium carbonate is more soluble than calcium carbonate and usually does not precipitate under the conditions prevailing. It is interesting to note that calcium salts have no effect on anglesite (lead sulphate) because calcium sulphate is soluble, but barium salts hinder the sulphidization of anglesite because of the precipitation of barium sulphate. Remedies When calcium sulphate is present in large amounts, the softening of the water with soda ash is usually too expensive to be considered, but the precipitation of the objectionable calcium carbonate can be prevented in two different ways. One is the use of sodium hydrosulphide instead of sodium sulphide. This salt gives a lower pH than sodium sulphide and does not bring about the immediate precipitation of the calcium which remains in solution as calcium bicarbonate. The other procedure is to add ammonium salts such as the sulphate or chloride which have the property of increasing markedly the solubility of calcium carbonate. Ammonium salts have other effects such as cutting down conditioning time and accelerating flotation. They should be added to the flotation cells rather than to the ball mills. Table I. Effect of Sodium Hydrosulphide and/or Ammonium Sulphate on the Flotation of Two Oxidized Lead Ores Mibladen Ore4 La Plagne Ored Con- Tall- Con- Tail-centrate ing centrate ing Reagents Pb, Pct Pb, Pct Pb, Pct Pb, Pot Without addition of CaSO, NaS 56.0 0.68 43.4 0.65 NaSH 56.2 0.60 40.4 0.50 Na2S + (NH4)2SO4d 54.6 0.56 NaSH + (NH4)2SO4d 43.0 0.66 With addition of 40 lb/ton CaSO4 Na2S 39.4 3.85 34.0 3.21 NaSH 49.1 0.70 49.6 0.88 Na2S + (NH4)2SO4d 53.9 0.85 NaSH + (NH4)2SO4d 51.0 0.45 41.1 0.78 In table I are given the results of representative tests on two different oxidized ores. They show that the strongly detrimental effects of calcium sulphate can be offset by the two procedures outlined above. Sodium hydrosulphide is now used regularly on a mill scale on certain ores. Tests are being carried out with ammonium salts. It should be noted that malachite is subject to influences similar to cerussite. One final word of caution—when the ore is rich in primary slime, which is flocculated by the calcium salts, it may be indispensable to remove these by washing or precipitation with sodium carbonate instead of keeping them in solution by the above methods. Acknowledgment We wish to thank Socibtk Miniere & Metallurgique de Penarroya and Minerais et Metaux, for permission to publish these results.

Jan 1, 1951

By H. A. Wilhelm, P. Chiotti, G. A. Tracy

A summary of analytical, X-ray, thermal, and metallographic data obtained in the study of the Mg-U system is presented. No intermetallic compounds are formed by these two elements, and their mutual solubility is limited at temperatures up to 1255°C. The compositions of the liquids which coexist at 1135°C under a pressure of 3 atm are 0.14*0.05 wt pet U in magnesium, and 0.004 wt pet Mg in uranium. The solubility of uranium in magnesium decreases to 0.0510.03 wt pet at 675OC, and to about 0.0005 wt pet at 650°C. Due to the reactivity of both uranium and magnesium toward crucible materials, the choice of a suitable crucible presented a problem. Crucibles made from high purity magnesia to which 10 wt pet MgF2 was added to reduce porosity proved to be satisfactory. Some observations made with the use of other crucibles are given. THIS investigation was made to establish the phase diagram for the Mg-U system. Ahmann,' formerly of the Ames Laboratory, did some work on the system. He used several methods in an attempt to prepare Mg-U alloys. One of the methods involved the reduction of UF, with a large excess of magnesium. In these experiments, the magnesium wet the surface of the uranium, but there was no evidence for compound formation. The maximum solubility of magnesium in uranium was indicated to be 0.01 wt pet. In another set of experiments, uranium chips as well as uranium powder were heated in contact with molten magnesium in a graphite crucible for periods of time up to 48 hr. A reaction layer was found at the Mg-U interface in several instances. X-ray analysis of the layer material showed the presence of UC and some additional unidentified lines which were interpreted as indicating the possibility of an intermetallic compound of uranium and magnesium. These studies indicated the maximum content of magnesium in uranium to be 0.043 wt pet. One sample of magnesium which had been heated at 1025°C in contact with excess uranium was found by chemical analysis to contain 0.275 wt pet U. Rules, based on empirical or semi theoretical considerations, which attempt to predict the alloying behavior of metals have been presented in the literature. Although these rules are not infallible, they nevertheless serve as useful guides. Using them, several generalizations can be made concerning the Mg-U system. According to Hume-Rothery's' atomic

Jan 1, 1957