Search Documents

By William Fink

SINCE so many different curves have been published for the solid solubility of zinc in aluminum, it seems desirable to definitely establish the correct curve by two or more independent methods. The curve published in part I1 was based entirely upon X-ray measurements because the other methods employed at that time were not satisfactory. The present paper (the seventeenth of this series on high-purity aluminum alloys) describes the determination of the solid solubility of zinc in aluminum by the measurement of electrical resistivity at temperature and by microscopic examination. Since the publication of our part I in 1932, an investigation of the solubility relations in the aluminum-zinc system has been reported by Schmid and Wassermann2, who obtained their solubility results from lattice-parameter measurements on heat-treated and quenched speci-mens. The diagram that they published is shown in Fig. 1. In this investigation they also found by X-ray measurements that the parameter of the gamma phase changed continuously with zinc content and at such a rate that it would be identical with that of the beta phase at 60 atomic per cent zinc. It was concluded therefore that the beta and gamma phases, from the point of view of structural relationship, are one single phase. They also suggested a gap of immiscibility between 270° and 350° C. The complete boundary in this region could not be deter-mined satisfactorily by the method employed and therefore was not shown in their diagram.

Jan 1, 1936

By Carle Hayward

THIS work was first undertaken in the metallurgical laboratory of the Massachusetts Institute of Technology in 1907 by L. A. Dickinson, E. Phelps, and V. S. Rood, under the author's direction. They attempted to determine the diagram for the system Cu2S-NiS, but several inexplicable results were obtained. The following year, P. H. Mayer with Mr. Dickinson carried, on some experiments with nickel sulphide and found that the molten material slowly lost sulphur until it reached a composition corresponding to the compound Ni3S2, established by Bornemann.1 At this point the composition remained stable. The freezing points of the mixtures gradually fell off with the loss of sulphur. Since the above facts seemed to explain the erratic results obtained in the first experiments, Mr. Mayer with F. Jaeger attempted in 1910 to establish a correct equilibrium diagram for the Cu2S-Ni3S2 series. They prepared pure Cu2S and Ni3S2 and determined the cooling curves for various mixtures. The fusions were made in a platinum resistance furnace and the temperatures were measured with a platinum-iridium thermocouple connected with a Sullivan galvanometer. The curve was established for mixtures containing more than 40 per cent. Cu2S, but they were unable to determine certainly the direction of the curve beyond that point. Nothing further was attempted with this series until the present year, when the work was carried to a successful conclusion with the assistance of A. Butts, Jr., and E. H. Weil. The results of this work are given in the following pages.

Jan 1, 1914

By R. D. Begley, A. W. Khair

Introduction The technique being investigated here uses a physical mine model which consists of a plexiglass room-and-pillar model 11.4 x 11.4 cm (4.5 x 4.5 in.). It is placed at the bottom of a larger plexiglass box 25.4 x 30.5cm (10 x 12 in.). The box is then filled with a model material representing geologic overburden. Sand has been selected because of its deformability under gravitational forces. The mine model is capable of creating a cavity and induces movement on the surface of the model material. This surface disturbance can be measured using a photographic technique called holographic interferometry. This paper discusses results of an investigation of the possibility of generating subsidence criteria using physical mine models and laser holographic interferometry. Problem Statement Subsidence appears to be widespread in two states - Pennsylvania and Illinois - although serious subsidence is found in localized areas of numerous other states (HRB Singer Inc., 1977). The US Bureau of Mines estimates that more than 1618 km2 (400,000 acres) of urban areas are threatened by subsidence. Pennsylvania and West Virginia contain 57% of these threatened areas, with the remainder being spread out over 16 states (Johnson and Miller, 1979). Events of subsidence have been reported in urban areas, including Pennsylvania (Gray et al., 1977) and Illinois (Mahar and Marino, 1981). One location has observed three episodes of subsidence beginning in 1950 (Bruhn et al., 1981). These subsidence events all occurred over abandoned room-and-pillar mines. Some mines have been abandoned more than 50 years (Bauer and Hunt,1981) . Available research does not offer much on the problem related to time dependent subsidence, especially those associated with the failure of remnant coal pillars. The physical modeling technique developed at West Virginia University is capable of measuring both instantaneous and time delayed subsidence. Laser Holographic Interferometry Laser holographic interferometry, or holometry, uses the interference properties of laser light to measure small movements of objects. The object requires only optical access and no surface instrumentation. This technique is closely related to photoelasticity. Both techniques rely on the uniqueness of the light reflected off or through an object in any given state of stress. The entire measurement process is done remotely without any surface instrumentation and without using a camera. The interferogram is constructed and visual observation will yield fringes on all areas that yielded or moved. The displacement represented by one fringe was determined by Wilson et al. (1977) and is given by the relationship: [d ='1(1) 2 cos 8 where d = displacement of one fringe 6 = incident angle of laser light A = wavelength of light (632.8 x 10-9 meters for Helium-Neon lasers)] In summary, holometry is capable of detecting very small movements of objects under study. It is a very sensitive process that requires laser light and vibration free experiments. Experimental Program Lab Facilities The primary components of the facilities were the laser and the optical table. The light source was 50 milli-watt, Helium-Neon laser. The optical table was a granite slab weighing nearly one ton. All experiments were performed on the optical table. It consists of a large table sitting on air cells similar to car innertubes. Six air cells were placed on top of two layers of wood and Styrofoam. Figure 1 is a schematic diagram of the vibration free table. Even with these precautions, the experiments still had to be performed at night to reduce potential traffic related vibrations. Room-and-pillar mine models consisting of three different pillar sizes were constructed out of plexiglass. The models were designed to represent three different extraction ratios. Figure 2 shows the models. The extraction ratios were determined by the tributary loading concept (Peng, 1978). These models were the primary component of a seam extraction simulator. A schematic of this simulation device is shown in Fig. 3.

Jan 1, 1986

The useful minerals can be subdivided into two large groups. One comprises those which are mined because of their chemical composition. They represent the natural resources of certain materials or of energy (coal). The second group is used not because of their chemical composition but because of certain physical properties or combinations of physical properties. A large number of minerals are mined because of their hardness, their electrical and thermal properties, their color or plasticity. There has been increasing recognition of the value of mineral synthesis during the past 30 years. This is illustrated by the development of improved aircraft spark plugs and chemical porcelain about the time of the first World War. During World War II the impact of crystal chemistry upon ceramics became most pronounced. New ceramic bodies were tailor-made, such as those designed with a high dielectric constant and low power loss, for use in high-voltage, high-frequency communication. In the field of refractories special materials were needed for unusual heat-resisting service in jet and rocket engines, and in the processing of fissionable materials. The synthesis of natural minerals in the laboratory has long been of aid to geologists and mineralogists in their study of the origin of minerals and physico-chemical conditions under which certain minerals were

Jan 1, 1950

By George F. Comstock

IT has been reported recently1 that the hardenability and toughness of forging steels may be improved appreciably by the use of complex deoxidizers containing titanium, aluminum, and vanadium. In the light of these results, an investigation of similar deoxidizers containing various hardening and grain-refining elements was proposed. These deoxidizers included three manganese-silicon-aluminum-titanium al- [ ] loys with and without boron and calcium, three titanium-aluminum ferroalloys with vanadium, molybdenum and zirconium, respectively, an aluminum-zirconium ferro-alloy, and plain ferroboron. Their approximate compositions are given in Table I, and the results obtained so far in the investigation of their effects on steel are presented in the later parts of this paper. METHOD OF USING DEOXIDIZERS The deoxidizers listed in Table I were used in three series of 0.40 per cent carbon steels, which were melted in a small basic-lined induction furnace and cast in the form of I7-lb. ingots about 2.75 in. square. The basic charge for each heat was 10 lb. Armco iron and 6 lb. of clean low-carbon sheet-steel scrap. When melted, this charge was deoxidized with 15 grams of ferrosilicon, then about 500 grams of pig iron was added to give the desired carbon content. After the pig iron was dissolved, nickel [ ] shot and high-carbon ferrochromium were added if required, and additions of 80 per cent high-carbon ferromanganese and 50 per cent ferrosilicon were made to provide the proper amounts of those elements. Aluminum was added to every heat 2 min. after the silicon, for grain-size control and preliminary deoxidation. One minute later the special deoxidizer was added to the clean bare surface of the molten steel, and 2 min. afterward the steel was poured into the ingot mold, using a hot-top and pipe-preventing compound after pouring to decrease the depth of the shrinkage cavity. The special deoxidizers were used mostly in the form of about ½ to ¾ -in. lumps,

Jan 1, 1942

By R. P. Aikman, F. G. Miller, J. M. Podgursky

As part of a larger study of the mechanism of froth flotation of coal, the rates at which coal particles of various size and specific gravity react to froth flotation were investigated. Results of this study show that in flotation: I) recovery rate increases, but selectivity decreases with a decrease in particle size down to 100 mesh, and 2) recovery rate is constant for all sizes between 100M and 325M. n response to the growing demand for low-sulfur coking coal for iron making, the coal industry is continually striving to perfect methods for cleaning coal to acceptable ash and sulfur levels while maintaining maximum product yield. By present standards the industry has adequate processes for cleaning coarse coal, i.e., + 28 mesh, at almost any desired specific gravity. However, in the case of fine coal, i.e., —28 mesh, neither of the two existing processes - froth flotation or hydrocycloning — in its present state of development yields products that are comparable in ash and/or sulfur content to products normally obtained from coarse coal processes. The work outlined in this paper is part of a larger study directed toward maximum exploitation of froth flotation for fine coal processing. The concepts and data presented are now serving as a basis for designing fine-coal circuits in which improved efficiency is obtained by optimum use of froth flotation with other fine-coal processing methods. The paper includes: 1) A discussion of the value of a detailed wash-ability study as a method of assessing the problems associated with fine coal processing, 2) A general discussion of hydrocyclone principles, included to serve as a basis for understanding the mechanism of coal flotation, and 3) A detailed discussion of the mechanism of coal flotation, as well as the research leading to the optimum use of froth flotation in combination with other fine-coal cleaning methods to provide efficient fine-coal processing. Our study of the rates at which coal particles of various size and specific gravity react to flotation shows that in flotation: 1) recovery rate increases but selectivity decreases with a decrease in particle size down to 100 mesh, 2) recovery rate is constant for all sizes between 100 mesh and 325 mesh, and 3) the flotation process effectively rejects only those extremely fine particles which do not contain surface carbon. (Because of this feature, froth flotation is an excellent method for rejecting clays - the only extreme fines in - 325-mesh coal that are always carbon free.) Washability studies of flotation products are used to assess flotation efficiency. These studies show that: 1) the increase in percent sulfur in flotation products above the theoretical sulfur content as defined by the washability study is due almost entirely to flotation of fine high-specific-gravity particles that are part coal and part pyrite, and 2) in a given size range particle floatability decreases with an increase in particle specific gravity. Error curves are explained and are used to compare the mechanisms of coal flotation and hydrocycloning. These comparisons show that hydrocyclone performance is affected primarily by particle mass, i.e., particle specific gravity and size, whereas coal flotation performance is dependent on both the particle mass and the coal surface available for bubble attachment. Since the error curve is a basic tool for rating the efficiency of any coal processing system, it will be useful to quickly review the principles of error curve construction. RATING COAL-PROCESSING EFFICIENCY BY THE ERROR CURVE The organic component of coal is of lower specific gravity than its impurities, and the most effective principle for coal concentration is therefore separation on the basis of specific gravity. However, since there is no sharp dividing line between pure coal and pure ash components, specific gravity must be closely controlled if the product is to have acceptable quality at maximum yields. In turn, the basis for close control in any coal processing system is the reference standard provided by precise laboratory washability studies. In these studies, coal is carefully separated into a series of progressively higher specific gravity fractions to establish a relationship

Jan 1, 1968

By A. J. Shaler

The subject of the mechanism of sintering has received much attention in the past few years, particularly since the beginning of the series of AIME seminars in powder metallurgy of which this paper introduces the fourth. In the first of these, F. N. Rhines1 brought together and discussed the available experimental data on the sintering of pure metallic powder, and succeeded in bringing to a sharp focus the attention of workers in this field on the established observations which a satisfactory theory must explain. Several other authors3,5,6 have, in the last few years, studied the phenomena that occur when cold metallic powders, loose or in the form of compacts, are first brought to elevated temperatures. Some workers' in the field of friction have recently studied the adhesion of solid metal surfaces when they are brought into close contact. These researches have indicated that several separate mechanisms operate simultaneously, at least during the first part of the sintering process. Some of them have been called transient mechanisms4 because they are in general not absolutely necessary to sintering. Powders may be so prepared and so treated that these transient phenomena do not take place during subsequent sintering. This does not mean, of course, that their industrial and scientific importance is any less than that of the steady-state phenomena. The latter are changes that go on during sintering no matter how the powders are made or treated; they cannot be divorced from sintering. One way to analyze the process of sintering into its component parts is perhaps to distinguish between these transient and steady-state phenomena. Some of the transient phenomena have been studied in the past few years. Huttig3 has shown that, when the temperature of metallic powder is slowly raised, the following events generally occur in order: (1) physically adsorbed gases are desorbed; (2) there is an atomic rearrangement of the surface, a sort of two-dimensional "surface-reciystallization"; (3) there is a breakdown of chemically adsorbed surface compounds; (4) there is a recrystalliza-tion in the volume of the metal. All these changes are shown by Huttig and his coworkers to be completed fairly rapidly at lower temperatures than those generally used in sintering and are therefore not a part of the mechanism whereby the density of a mass of powder continues to change after long heating at an elevated temperature. But the first and third of these changes release gases in quantities which may or may not help to control the steady-state mechanisms, depending on when the voids become isolated from the outside of the compact. Among the phenomena studied by Steinberg and Wulff,8 there is the effect on sintering of residual stresses arising from the pressing operation. They found that the lateral surfaces of a green compact of iron are under a longitudinal residual tension-stress of the order of magnitude of half the yield-point for solid iron. If the outside surface is in tension, the core must be under longitudinal compression. When the compact is heated, the surface residual stress is thermally relieved first, and the compact therefore initially expands in the direction of its axis. This is a transient phenomenon, if for no other reason than the possibility of sintering unpressed powders, as demonstrated by Delisle,9 Libsch, Volterra and Wulff10 and others.1 The subject of recrystallization is dealt with further in a separate section, in view of its prominent place in sintering literature. It, too. is one of these transient phenomena. Among the steady-state parts there may be distinguished the attraction between particles and its consequences, the spheroidization of voids in the compacts, and the densification or swelling of the compact. There is considerable evidence4,7 showing that cold metallic surfaces, when brought to within a few interatomic distances of one another, are attracted to each other by forces of the order of many thousands of pounds per square inch. A calculation, discussed in greater detail in another section, shows that this force changes but slightly when the temperature of the surfaces approaches the melting point. Actual measurements of forces of adhesion of this magnitude have been made by Bradley12 on some nonmetals, but none has yet been made on cold or hot metals. This force is of sufficient magnitude to cause some plastic deformation in powder compacts, as will be shown below. A second force of steady-state nature is due to the surface tension, which probably has the same origin as the force of attraction between surfaces.164 A paper by Udin, Shaler, and Wulff1,3 gives the results of precise direct measurements of its value for solid copper. The demonstration of the tendency for the surface tension to shrink a pore was long ago given by Gibbs.17 He showed that its effect on a curved surface between two phases is equivalent to a pressure perpendicular to that

Jan 1, 1950

By D. Turnbull, J. H. Hollomon

THERE is a large body of evidence'" indicating that solidification during the liquid-solid transition is usually induced by heterogeneities present in the liquid. By dispersing liquid metals into small droplets, the impurities responsible for catalyzing solidification are isolated within a small number of these droplets. The effect of the foreign body therefore is restricted to a single drop by this technique. Thus upon cooling below the melting temperature, solidification is initiated by homogeneous nucleation in the majority of the droplets that do not contain impurities. In the case of solidification of liquid metals, the activation energy for nucleation is so great that its rate changes by orders of magnitude for a change in temperature of only several degrees centigrade.' Effectively homogeneous nucleation occurs at a critical temperature upon continuous cooling. Thus by microscopic observation of single particles during cooling, a temperature at which the rate of homogeneous nucleation becomes sensible can be determined.3 since at the temperatures at which nucleation occurs in the absence of impurities the rate of crystal growth is extremely rapid, the temperature at which the entire particle solidifies is very nearly the temperature at which the nucleation of the solidification occurs. Thus for liquids that freeze at high temperatures the onset of nucleation can be established by simply observing the temperature at which the marked heat evolution and increase in brightness of the particle occur. For liquids that freeze at lower temperatures the onset of nucleation can be determined by a rumpling and change in shape of the particle resulting from its solidification. The microscopic technique for observing the solidification of small particles has already been described." In earlier papers the nucleation of solidification of pure metals 5,6 and of alloy systems7 showing complete liquid and solid solubility have been described. In the present paper, the observations are extended to a simple eutectic system (Pb-Sn) where the possibility of the formation of two solid phases exists. Metals for the investigation were obtained from the American Smelting and Refining Co. in the form of pure lead and pure tin, 99.8 and 99.9 pct purity, respectively. An ingot of each of the pure metals was made into shot by heating the metals at a temperature about 50 °C in excess of the melting point and pouring the liquid slowly into a container of water at 15°C. Samples of the shotted pure metals were weighed out to make alloys containing 5, 10, 15, 20, 25, 30, 40, 50, 60, 70, 80, and 90 atomic pct Pb. Samples of each alloy were then melted in separate beakers. Each melt was poured through a pyrex funnel into a cylindrical mold (% in. ID). The casting solidified in 10 to 20 sec. The inside of the mold as well as the funnel through which the metal was poured were coated with graphite to eliminate adherence of the metal. Analyses were performed on some of the compositions and are given in Table I. The compositions also were checked for these samples and for those that were not analyzed by determining the spread between the liquidus and the solidus upon melting the small metal particles. These measurements agreed as well with the nominal compositions as the analyses listed above. Results The results of the supercooling experiments for the several alloys are summarized in Table II and plotted on the constitution diagram in Fig. 1. Data for the pure lead and pure tin were taken from earlier investigations. The values for the maximum supercooling of the several alloys are the average of several determinations on a number of drops of each alloy. The maximum value in any determination was within about 2 pct of the average. For the alloys containing from 20 to 60 atomic pct Sn, inclusive, two marked changes of the surface structure were observed upon cooling. At the higher temperature, after the first appearance of the solid phase it continued to grow slowly at a constant temperature and then stopped. At the lower temperature the alteration of surface structure was abrupt. For the alloys containing from 70 to 95 atomic pct Sn, inclusive, an abrupt change in surface structure was observed at a single critical temperature.

Jan 1, 1952

By V. Pasupathi, R. E. Hummel, J. W. Koger

Specimens of P1 brass were plastically deformed at room temperature to various degrees of deformation and subsequently cooled in order to transform them to low-temperature martensite. Deformation shifts Ms. A, , and the temperature of minimum resistivity to lower temperatures, and also decreases the temperature coefficient of electrical resistivity. These properties change rapidly up to about 15 pct reduction but vary very little with higher deformation. The possible relationships between martensite formed by deformation and the M, temperature of low-temperature martensite are discussed. Evidence is given that deformation martensite delays the formation of low-temperature martensite. BETA' brass undergoes at least two different types of martensitic transformations. One of these transformations (B1- B2) was first observed by Kaminski and ~urdjumov' and occurs when 81 brass with a zinc content between 38 and 42 wt pct (quenched from the single-phase region) is cooled below room temperature. Jollev and Hull' determined the structure of 0" from X-ray and electron-diffraction data as ortho-rhombic. Kunze came to the conclusion that the super-lattice cell of 0" is one-sided face-centered triclinic (pseudomonoclinic). The second martensitic transformation (B1-A1) occurs when the specimens are deformed at or somewhat above room temperature. This type of martensite will be called deformation martensite. Horn-bogen, Segmuller, and Wassermann4 determined the structure of deformation martensite to be bct. (An intermediate phase, az, occurs before the final phase appears.) At deformations higher than 70 pct, a, transforms into a.4 A critical temperature Md exists above which no transformation occurs during deformation and is estimated to be around 400°C in P1 brass.5 This martensite has elastic properties.6 When the sample is stressed, martensitic plates appear; when the stress is released, the plates disappear. The present paper studies the effect of deformation martensite on the formation of low-temperature martensite. The experiments involved samples of 8, brass which were plastically deformed by various amounts and were subsequently cooled below the transformation temperature. EXPERIMENTAL PROCEDURE The 13 brass investigated was made from 99.999 pct pure copper and 99.9999 pct pure zinc and contained 38.8 wt pct Zn. The specimens, consisting of foils 0.1 mm in thickness, were heat-treated at 8'70°C for 15 min in an argon atmosphere and then quenched into ice water. They were then deformed by cold rolling and subsequently cooled at a rate of 1°C per min. The martensitic transformation that occurred during cooling was followed by electrical resistivity measurements. The resistance measurement technique and its accuracy have been described in a previous paper. Because the transformation 81 —-8" occurs below room temperature, the samples were placed in a cryo-stat which contained isopentane as a cooling medium. The isopentane was cooled by liquid nitrogen pumped under pressure through a 15-ft coil of copper tubing which was immersed in the isopentane. The nitrogen flow was regulated by a temperature controller using two thermistors in the cooling medium. The cryogenic liquid could be heated with an immersion heater. The useful temperature range with this device was from +25° to approximately -155~C. EXPERIMENTAL RESULTS Resistivity Measurements. The following abbreviations are used in this paper to label the characteristic temperatures during the martensitic transformation. M, is the starting point of the martensitic transformation and is defined as that temperature where the resistivity vs temperature curve on cooling first deviates from a straight line. Mf is the temperature at which the martensitic transformation is completed. On reheating, the transformation from martensite to the parent phase starts at a temperature A, and ceases at a temperature Af. Fig. 1 presents five different resistivity vs temperature curves corresponding to the transformation of brass from Dl to 8" after different degrees of reduction in thickness. The following observations can be made from these curves. 1) With increasing degree of deformation the Ms temperature is shifted to lower temperatures. This shift ranges up to 35°C compared to the undeformed state. This is also indicated in Fig. 2, where AM, (the shift of Ms, compared to the undeformed state) is plotted vs the degree of deformation. AM, increases rapidly until a reduction of about 15 pct is reached. With higher deformations, no additional increase in AM, was found. 2) With increasing degree of deformation the temperature of minimum resistivity (M) is also shifted to lower temperatures. The shift, attains a maximum of about 61°C compared to the undeformed state. In Fig. 3, AM is plotted as a function of deformation. It can be seen that, as in 1 above, AM increases rapidly and no further shift of M occurs for deformations greater than 15 pct. 3) The temperature coefficient of resistivity, is given by the slopes (dp/dT) of the linear portions of

Jan 1, 1969

By George F. Learning

TOTAL DIRECT IMPACT The uranium mining industry's principal economic impacts on the Texas economy are the result of three flows of money from the industry into the remainder of the state's economy. These three are: (1) money paid to individuals (personal income) ; (2) money paid to other businesses (business income); and (3) money paid to state and local governments (government revenues). As these direct payments from the uranium industry to various other sectors of the Texas economy subsequently circulate and recirculate within the state, the indirect effects of uranium mining's direct impacts multiply to reach amounts significantly higher than the direct income flows alone. Over the past decade, the uranium mining industry has substantially increased its role as a provider of jobs, personal income, business income, and government revenues in Texas. The growth has come almost exclusively in a largely rural, seven-county area that lies within the triangle formed by the Laredo, San Antonio, and Corpus Christi metropolitan areas. The uranium mining industry, in fact, has been the major dynamic element in this rural area despite relative stagnation in most of the region's other basic economic sectors. Over the three years from 1976 to 1978, the South Texas uranium mining industry directly contributed a total of $115 million to the economy of the seven- county region in which it operated and $164 million to the economy of the entire state of Texas. In 1979 alone, the total direct contribution of the industry to the Texas economy had climbed to $124 million in personal, business, and government income. PERSONAL INCOME IMPACT In the period from 1976 through 1978, the South Texas uranium mining industry provided an average of $12.5 million in personal income each year directly to residents of Atascosa, Bee, Duval , Karnes, Live Oak, McMullen, and Webb counties -- the seven Texas' counties that make up the South Texas Uranium Belt. A1 though 84 percent of this resulted from the employment of area residents in uranium industry jobs, some amounts were also provided by the payment of rents and royalties to land owners for the use of their land and mineral rights in uranium mining operations. In 1979, the uranium industry provided approximately $38 million to residents of the Uranium Belt and the rest of Texas. This was more than double the average of $16.1 million provided to Texas residents during the 1976 to 1978 period. The full importance of the uranium industry as a source of personal income, however, should not be reckoned merely by the amount of wages and salaries that it pays directly to its own employees, nor by its rent and royalty payments paid directly to land and mineral rights owners living in Texas. The added payments that the industry makes directly to other Texas businesses and state and local governments in Texas are themselves converted into personal income as those business firms and government units in turn pay their employees. All of the direct income payments made by the uranium industry circulate and recirculate within the state's economy, multiplying their impact as they go, until they eventually all leak out of the state as federal taxes or as payments to individuals or businesses located outside of Texas. The combined circulation and recirculation of the direct personal, business, and government income that was provided by the-uranium industry in Texas during 1976, 1977, and 1978 resulted in an average annual amount of indirect personal income of more than $83 mill ion. This alone was $20 mill ion more than the industry's average annual sales during the same years. The total of combined direct and indirect personal income contributed to the Texas economy by the uranium mining industry in that same three-year period thus averaged almost $100 million annually. In 1979, the amount of indirect personal income contributed to the Texas economy by the circulation of uranium mining's direct contributions had risen to about $196 million, more than double the average of the previous three years. The combined direct and in- direct personal income impact in 1979 thus amounted to $234 million. BUSINESS INCOME IMPACT The income provided directly to other Texas business firms through the purchase of needed goods and services by the uranium industry has been twice as big as the industry's payrolls. In 1976, 1977, and 1978, the South Texas uranium industry spent an average of almost $36 million each year to buy both goods and services from other Texas businesses. By 1979, this direct contribution to the Texas economy had swollen to $76 million. The biggest share of the uranium industry's payments to other businesses have gone to contracting firms, including both construction firms and those providing specialized mining services. In the past four years, about 40 percent of the direct payments made by Texas uranium producers to other Texas firms have been to contractors. Texas wholesale and retail firms have also shared in the business sales provided by the South Texas uranium mining industry. Over the past four years, Texas wholesale and retail trade businesses have accounted for about 34 percent of the uranium mining industry's purchases from other Texas businesses. Public utilities firms have received another six per- cent, while Texas manufacturers and transportation firms have accounted for about five percent each. The other sectors of the state's economy, including other mineral industries, agriculture, finance, insurance, real estate, and services, have accounted

Jan 1, 1980

By W. F. Carew, F. A. Crossley

The stress for rupture in 500 hr at 1000° F has been reported to be about 13,000 psi higher for Widmanstitten than for equiaxed microstructures for the Ti-7A1-3Mo alloy.1,2 Also, limited data indicated Widmanstatten and equiaxed micro-structures to have approximately the same creep resistance at 1000°F.' Recently, data have been obtained which show Widmanstatten structures to be significantly more creep resistant than equiaxed structures at 1000°F, see Fig. 1. These data represent several ingots and several heat treatments of the solution treat and age type. The thermal history and tensile properties corresponding to the creep data are given in Table I. The creep data were taken from creep-rupture tests. The associ- ated rupture data are given in Table 11. It may be noted that total creep deformations are considerably greater for equiaxed structures. Previous evaluations of stability indicated that all of the structures tested are stable with respect to exposure to stress at elevated temperature.1,2 For a minimum creep rate of 10-4 in. per in. per hr the difference in stress levels is indicated to be about 17,000 psi. Holden,et found an irreversible contraction upon heating three a-ß titanium alloys in the equiaxed condition above their ß-transus temperatures. The alloys were: Ti-6Al-4V, Ti-155 A (5Al-1.3Cr-1.5Fe-1.2Mo), and C-130 AM (44-4Mn). The net contractions in length between the original equiaxed and the final Widmanstatten structures measured at room temperature were: 0.4, 0.4, and 0.7 pct, respectively. The greater creep and rupture resistance of the WidmanstStten structure of the Ti-7Al-3Mo alloy may be associated with the phenomenon

Jan 1, 1959

By S. C. Das. Gupta, B. S. Lement

isothermal formation of martensite occurs in the range of —65o to —197oC and is always preceded by some athermal transformation. By rapid cooling the isothermal, but not the athermal, component of transformation can be suppressed. Stabilization against isothermal transformation can be induced by cycling from below M. to room temperature. A LTHOUGH the transformation of austenite to XV martensite is generally believed to occur only on cooling, recent evidence indicates that this reaction can also occur at constant temperature. Isothermal formation of martensite was observed in tool steel by Fletcher, Averbach, and Cohen.'. They found that the hardening reaction that occurs during the quenching of a plain carbon or low carbon alloy tool steel does not stop immediately when room temperature is reached; instead austenite continues S. C. DAS GUPTA is Research Fellow, Department of Metallurgy, University of Notre Dame, Notre Dame, Ind. B. S. LEMENT, Associate Member AIME, is on the Research Staff, Department of Metallurgy, Massachusetts Institute of Technology, Cambridge, Mass. Discussion on this paper, TP 3123E, may be sent, 2 copies, to AIME by Dec. 1, 1951. Manuscript, April 16, 1951. Detroit Meeting, October 1951. This paper represents part of a thesis by S. C. Das Gupta submitted in partial fulfillment of requirements for the degree of Doctor of Philosophy in Metallurgy to the University of Notre Dame. to transform at room temperature although at a decreasing rate. Since only a small amount of austenite transforms in this fashion, isothermal formation of martensite was considered to be merely a "tailing off" effect of the main hardening reaction. Another point of view was advanced by Kurd-jumov and Maksimova"' * who reported that the austenite-martensite reaction could be suppressed by rapid cooling of a 6 pct Mn-0.6 pct C steel in liquid nitrogen and that as much as 25 pct martensite could be formed by reheating to and holding at subzero temperatures above that of liquid nitrogen. These investigators came to the conclusion that martensite is thermally nucleated at certain special regions in the austenite and subsequently grows to observable dimensions. Isothermal transformation of austenite to martensite was cited by Fisher, Hollomon, and Turnbull" as evidence supporting another nucleation and growth theory of martensite formation. According

Jan 1, 1952

F. E. BACHMAN, Port Henry, N. Y. (written discussion*).-Experi-ments with titaniferous ores found in Essex County, New York, made by the MacIntyre Iron Co. in 1914, showed' that titaniferous concentrates are reduced in the furnace with no greater, and probably with less, expenditure of heat, and consequently of fuel, than non-titaniferous mag-netites; and as a greater proportion of their oxygen is removed by carbon monoxide than is the case with non-titaniferous magnetites, a lower fuel consumption for the reduction of iron may be expected. After the furnace was blown out at the end of the experiment, the formation in the hearth was found to be abnormal. The brickwork was replaced, entirely around the furnace, by a layer which at -the tuyere circle was made up of cinder, fine carbon, and coke; the coke, however, gradually disappeared toward the bottom, being replaced by cinder and graphite. The usual salamander of graphite and iron was missing. The material left in the hearth seemed to be cinder that had not drained from the last cast; its composition, though, would indicate that it was in the furnace previous to the taking off of the titaniferous ore. At first, this material was thought to be blast-furnace cinder mixed with less iron and graphite than is normal; but an examination showed it to be made up of cinder with small masses of iron and graphite. There were also patches of a steel-gray material having a metallic luster; a microscope showed these patches to be made up of black metallic crystals interlacing white crystals.

Jan 11, 1919

By W. W. Odell

THE sulfur content of coal is perhaps more important in the manufacture of illuminating gas than in any other coal-using industry. Whether the gas is made by the distillation of coal in retorts or ovens or by steaming incandescent coal or coke in the water-gas process, a portion of the sulfur present in the fuel always passes into the crude gas. Practically all the sulfur that remains in the finished gas is transformed into sulfur dioxide (SO2) when the gas is burned. Sulfur dioxide is a pungent suffocating gas and, if present in the air in any perceptible amount, is deleterious to health and comfort and damaging to house furnishings. So universally is this recognized that laws regulating the amount of sulfur that may be permitted to remain in the gas are very generally in force. The capacity of a plant to purify gas frequently limits the selection of coal for gas making. This condition may arise from different causes. Some plants were originally designed to handle a certain grade of low-sulfur gas coal, and very little leeway was allowed for growth or for the use of inferior coals. Other plants, when built, had ample capacity to purify gas from relatively higher sulfur coals, but their output has grown so rapidly that their purifying capacity is now limited and only- the low-sulfur coals can be handled. There is a great quantity of coal in the United States that would satisfy the requirements of the gas manufacturer, were it not for the high sulfur content. The coals containing less than 1 per cent. sulfur are becoming scarcer year by year and, in time, the gas industry will probably be compelled to use coals that are now considered out of the question.

Jan 9, 1919

By Max W. Bowen, A. J. Weinig

The important part that dissolved oxygen plays in the cyanide treatment of gold and silver ores is commonly recognized by most metallurgists and mill men. But heretofore there has been no simple method on which the mill man could rely for determining the amount of oxygen in the various mill solutions. A few methods are adaptable to the laboratory, such as the gasometric1 determination by actually measuring the oxygen, Winkler's2 iodometric method, and Schutzenberger's3 method, which depends on the reducing action of sodium hyposulfite on a blue solution of indigo carmine; but these are not readily adaptable to the needs of the mill man and cannot be applied to cyanide solutions without modification. The gasometric method is the most accurate but it takes too long to complete a determination. White's4 method (a colorimetric method that depends on the degree of coloration imparted to a solution of pyro-gallic acid in the presence of caustic soda) although much more rapid than any of the methods named, often gives misleading results on account of grading of colors of different solutions, which nearly always contain various kinds of salts. The method herein described was devised for the use of the mill man, the aim being to develop a simple, practical, accurate method. It is a modification of the Schutzenberger method and depends on the reducing

Jan 1, 1925

By Scott Turner

MY YEAR OF SERVICE as president of the A.I.M.E. came at a time when the mineral industry had suffered severely because of disturbed economic conditions throughout the world. The Institute, an integral part of this industry, had been similarly affected. Its membership and revenues decreased; it was confronted by problems of retrenchment at a time when its vigorous operation was especially important to its members, of some moment to the mining industry, and of value to the nation. Throughout the last year, the recession of activity in our industry continued with slight abatement. Your Board accordingly exercised such economy within the Institute as was possible without impairment of essential functions. It endeavored to aid in sustaining the morale of members, their sense of professional unity, and their interest in maintaining research and the interchange of scientific and technologic data upon which the progress of our industry depends. Effort was made to assist in the difficult task of finding employment for needy members; our endeavors have met with some success.

Jan 1, 1933

By C. K. Donoho

SILICON is used in almost all commercial steels; up to about 0.20 pct in killed wrought steels and 0.50 pct in steel castings. Above about 0.50 pct in wrought steels and 0.70 pct in cast steels, silicon is considered an alloy. As an alloy, silicon is useful for several purposes: (I) for its effect on magnetic properties of parts for electrical apparatus; (2) for increasing the yield strength of carbon and low-alloy steels without too much sacrifice of ductility and weldability; (3) for adding hardness and toughness to spring and chisel steels; (4) for adding resistance to scaling and carburization to heat-resistant steels; and (5) for its graphitizing effect in graphitic steels. In acid electric steels for casting we are principally interested in the effect listed second; i.e., increase of strength with minimum sacrifice of ductility.

Jan 1, 1947

By Dick Whittington, W. R. Taylor

GENERAL In mid-1974, a representative of ARCO Petroleum Company walked into our Austin offices and asked for a permit for ARCO's first Clay West Mine site. This was the first in situ uranium mining permit issued in the United States. That initial permit, issued in January 1975, was for three acres. The four years since have been characterized by growth and change. Today there are 16 permits approved for approximately 1,540 production acres issued to five companies at eight sites in four counties. There are approximately seven additional permit applications being processed or on the verge of being submitted for an estimated 2,000 additional acres of production. As a rough gauge of the financial scope of this activity, at the typical 40 production wells per acre and an estimated $2,000/well, operators hale installed or committed $122 million for production wells. This does not account for the exploration and development wells installed to delineate the ore or the cost of processing facilities for extracting the uranium. HISTORY OF URANIUM MINING IN TEXAS Information I have concerning early in situ uranium mining activities is "sketchy" but the apparent first on-site test of in situ uranium mining was conducted between 1967 and 1971 at the Dueterstat site, north of Yorktown in Gonzales County, by City Service. Others ran tests at the Bruni site in Webb County and the Burns and Clay West sites in Live Oak County in the mid-70's. During this period, Texas Water Quality Board personnel in the central and district offices maintained a general surveillance of these various test activities. Regulation of in situ uranium mining was formalized with the issuance of a permit in January 1975 with the advent of ARCO's initial production scale (3 acre) effort in the Clay West area at the Moser mine site. Since 1975, the accelerating rate of mining and exploration activity is noticeable. There were 16 exploratory rigs operating early in 1977. This year, the rig count is averaging 46--a 287% increase. HISTORY OF LEGISLATION Paralleling this mining activity was state and federal legislation which subjected in situ mining to environmental regulation. The following is a brief chronology of the legislation that is directly or indirectly related to uranium mining. As most of you know, disposal wells are an integral part of most in situ uranium mines operating in Texas. They are used both during production and during aquifer restoration following production. The wells are regulated by the Texas Injection Well Act, enacted in 1961 by the Texas Legislature. In 1967, the Water Quality Act established the Texas Water Quality Board, and provided for the regulation of water quality by the so-called permit system. In 1969, the Solid Waste Act was enacted by the Texas Legislature. The legislation provides for control of wastes from manufacturing, mining, and agriculture. This Act regulated uranium surface mining activities until 1975 when the Texas Surface and Mining Reclamation Act placed responsibility with the Railroad Commission for uranium open-pit mining and surface mining of coal and lignite. In 1972, the Federal Water Pollution Control Act (Public Law 92-500) was passed. This legislation forms the legal base for the NPDES (National Pollutant Discharge Elimination System) and the subsequent point source effluent guidelines and standards. The November 6, 1975 issue of the Federal Register published interim final rules for Best Practical Treatment levels for effluent discharges from ore mining and dressing operations. Litigation was immediately initiated by eleven companies against these proposed rules, and they are currently being reconsidered for reissuance in 1979. In 1974, the Federal Safe Drinking Water Act (Public Law 93-523) was enacted. A part of this legislation is the Underground Injection Congrol Program. The regulations implementing this program have undergone various public hearings and it is expected that they will be published in the Federal Register before the end of 1978. In 1975, the Texas Surface Mining and Reclamation Act (Senate Bill 55), providing for the Railroad Commission's authority to require reclamation of surface mines, was passed. In 1977, an amendment to Senate Bill 55 was introduced that proposed to place regulation of in situ mining of coal, lignite, and

Jan 1, 1979

By R. Q. Shotts

Data are presented which show that fractions of varying densities from the same coals are oxidized at different rates by nitric acid. From oxidation data, the approximate quantity of "bright" and "dull" components may be calculated. Definite relationships between oxidation rate and rank are shown for density fractions from at least two bituminous coals. IN 1945, the Alabama State Mine Experiment Station initiated a program on the determination of fusain in certain coals of the state.1 Because of the lack of equipment and personnel necessary for microscopic examination, the chemical method2 was used exclusively. During studies of the distribution of fusain in fractions of various sizes and densities on a medium volatile coal, the author noted a higher rate of oxidation of the nonfusain part of the coal in the lower density fractions and the difference in rate became more marked the shorter the oxidation period used. Since durain and other "dull" components of coal have been reported3,4,5 to have higher densities than vitrain and the bright components, it appeared probable that the observed differences in rates of oxidation in the different density fractions were due to variations in petro-graphic composition. Such effects have been noticed by other workers.2,3 In order to obtain further evidence on this point, several Alabama coals of different rank have been separated into three or more fractions on the basis of density and their rates of oxidation determined, using the procedure specified for the determination of fusain, except that measurements were made at short time intervals as well as for the longer periods specified in the regular procedure. Significant differences in the rates of oxidation of the nonfusain part of the various fractions have been observed, and it is believed that studies of this type may make possible the identification of individual petrographic components or lead to methods for their semiquan-titative estimation. Properties of the Coals: Analyses and some properties of the whole coals studied are given in table I. The range in rank of the coals is not the widest possible within the state, but samples of the low volatile coals that occur in thin beds in the northeastern part of the state, were unavailable. The Clements bed is not, at present, considered workable. The coal is of medium volatile rank, quite friable, and very strongly swelling. Analyses of different size fractions show that the larger sizes are of higher rank than the smaller ones. Material passing the No. 50 sieve (all sieve sizes refer to the U. S. Standard Series) is close to high volatile A in rank, except for the size passing a No. 200 sieve, in which fusain is partially concentrated. Because of the variation in rank of the sizes of Clements coal, oxidation studies were made of two widely different size ranges. The + 1-in. material was crushed on rolls to about 1/8 in. and separated into five fractions by float-and-sink treatment in a benzene-carbon tetrachloride mixture. The — No. 4 + No. 8 and the — No. 4 + No. 50 size ranges tested overlap but the latter size was studied last with the expectation that it would include more oxidizable material than the first size. This proved not to be the case. Yields and properties of the specific gravity fractions oxidized are shown in table II. Milldale bed coal probably represents, as nearly as it is possible to do so, the "average" coal of the state. The material passing a No. 4 sieve was the only size range oxidized. It was divided into four specific gravity fractions. As in every case the heaviest fraction, which was essentially rock, was discarded. The Black Creek is the most extensive in area of

Jan 1, 1951

By R. Q. Shotts

Data are presented which show that fractions of varying densities from the same coals are oxidized at different rates by nitric acid. From oxidation data, the approximate quantity of "bright" and "dull" components may be calculated. Definite relationships between oxidation rate and rank are shown for density fractions from at least two bituminous coals. IN 1945, the Alabama State Mine Experiment Station initiated a program on the determination of fusain in certain coals of the state.1 Because of the lack of equipment and personnel necessary for microscopic examination, the chemical method2 was used exclusively. During studies of the distribution of fusain in fractions of various sizes and densities on a medium volatile coal, the author noted a higher rate of oxidation of the nonfusain part of the coal in the lower density fractions and the difference in rate became more marked the shorter the oxidation period used. Since durain and other "dull" components of coal have been reported3,4,5 to have higher densities than vitrain and the bright components, it appeared probable that the observed differences in rates of oxidation in the different density fractions were due to variations in petro-graphic composition. Such effects have been noticed by other workers.2,3 In order to obtain further evidence on this point, several Alabama coals of different rank have been separated into three or more fractions on the basis of density and their rates of oxidation determined, using the procedure specified for the determination of fusain, except that measurements were made at short time intervals as well as for the longer periods specified in the regular procedure. Significant differences in the rates of oxidation of the nonfusain part of the various fractions have been observed, and it is believed that studies of this type may make possible the identification of individual petrographic components or lead to methods for their semiquan-titative estimation. Properties of the Coals: Analyses and some properties of the whole coals studied are given in table I. The range in rank of the coals is not the widest possible within the state, but samples of the low volatile coals that occur in thin beds in the northeastern part of the state, were unavailable. The Clements bed is not, at present, considered workable. The coal is of medium volatile rank, quite friable, and very strongly swelling. Analyses of different size fractions show that the larger sizes are of higher rank than the smaller ones. Material passing the No. 50 sieve (all sieve sizes refer to the U. S. Standard Series) is close to high volatile A in rank, except for the size passing a No. 200 sieve, in which fusain is partially concentrated. Because of the variation in rank of the sizes of Clements coal, oxidation studies were made of two widely different size ranges. The + 1-in. material was crushed on rolls to about 1/8 in. and separated into five fractions by float-and-sink treatment in a benzene-carbon tetrachloride mixture. The — No. 4 + No. 8 and the — No. 4 + No. 50 size ranges tested overlap but the latter size was studied last with the expectation that it would include more oxidizable material than the first size. This proved not to be the case. Yields and properties of the specific gravity fractions oxidized are shown in table II. Milldale bed coal probably represents, as nearly as it is possible to do so, the "average" coal of the state. The material passing a No. 4 sieve was the only size range oxidized. It was divided into four specific gravity fractions. As in every case the heaviest fraction, which was essentially rock, was discarded. The Black Creek is the most extensive in area of

Jan 1, 1951