Search Documents

By J. Washburn, R. Drouard, E. R. Parker

Temperature dependence of the rate of recovery in zinc single crystals after a simple shear deformation at low temperature was investigated. Some tentative suggestions regarding the annealed and strain-hardened states of a crystal are discussed. RECOVERY may be defined as the gradual return of the mechanical and physical properties of strain-hardened metal to those characteristic of the annealed material; an increase in temperature increases the rate of recovery. The annealing process in strain-hardened polycrystalline metals is complicated by the inhomogeneity of strain which always exists in aggregates. Polygonization in bent regions of the crystals and growth of new almost strain-free grains starting at points of severe local distortion1-:' make it almost impossible to isolate and study the recovery process. Homogeneously strained single crystals, however, do not polygonize or re-crystallize and hence they can be used advantageously to study recovery. In such crystals strain hardening is completely removed by recovery alone. Since recovery is a process whereby certain lattice disturbances introduced by plastic flow are gradually reduced, a knowledge of the rate and temperature dependence of this process for various conditions of prestrain might be helpful in formulating a model of the strain-hardened state. For simplicity it seemed desirable to limit the type of prestrain to the simplest obtainable, i.e., simple shear strain. In the experiments to be described, recovery was studied by observing changes in the stress-strain curve of prestrained zinc single crystals held for various times at temperatures above that employed for straining. Single crystals were grown from the melt by a modified Bridgeman technique from Horse Head Special zinc 99.99 pct pure, and from spectrographically pure zinc 99.999 pct pure. They were grown as 1 in. diameter spheres and acid-machined' to the final specimen contour. The test section was a cylinder about 1/8 in. high and 3/4 in. in diameter. The conical sections adjacent to the test section were cemented into the grips so the load could be transmitted to the crystal as uniformly as possible. The specimens were oriented so that in testing the maximum shear stress was applied along one of the slip directions, [2110], in the (0001) plane. Details of the production and testing of such specimens have been presented.' Each test was carried out according to the following schedule: 1—The crystal was strained at — 50°C until it reached a maximum shear stress, ,,,. The strain rate was approximately 5 pct per min in all cases. 2—After straining, the crystal was unloaded before the temperature was changed. Unloading required about 3 min. 3—The temperature of the specimen was then increased from — 50°C to the temperature, T, of recovery. This change in temperature was completed in a time of less than 2 min. The specimen remained at temperature, T, for a time, t, which differed for the various specimens. 4—Thereafter the temperature was again reduced to — 50 °C in approximately 3 min. 5—While at —50°C, the stress-strain curve after recovery was obtained. 6—The specimen was then unloaded and annealed for 1 hr at 375 °C in a helium atmosphere to bring about complete recovery. Cooling to room temperature after anneal required 90 min. 7—The same crystal could be re-used for another test because the plastic properties after annealing closely duplicated those of the original crystal. The specimen was immersed during the test in a bath of methyl alcohol which, through a system of tubes, could be pumped through either of two heat exchangers to regulate the temperature; this was accomplished by circulating the liquid through coils immersed in a bath of acetone and dry ice for cooling or in a bath of warm water for heating. Test temperatures were thus maintained constant within ±1°C. The — 50°C temperature was low enough so that no measurable recovery occurred during unloading and reloading. The stress-strain curve continued after recovery along a path below, but approximately parallel to, the path of a curve obtained in an uninterrupted test. Fig. 1 shows some of the results from a specimen of 99.999 pct Zn. The amount of downward displacement of the curve due to recovery was a

Jan 1, 1954

T.B.King (Depaytment of Metallurgy, Massachusetts Institute of Technology)— A valuable contribution of the authors is in the factual information which they have been able to gather; this type of information is quite difficult to obtain. In many respects, however, it would have been better if they had not subsequently embarked on a discussion of the chemistry of the converter process. It seems inconceivable that the authors do not refer to the papers of Schuhmann and his associates14 which have set the thermodynamic foundation for the whole copper smelting operation. In addition, a very useful review on the physical chemistry of copper smelting by Ruddle 5 appeared as long ago as 1953. An examination of this literature would have convinced the authors that there is no cause to be surprised at a correlation between the magnetic content and the silica content of converter slags, though they rightly point out that one should distinguish between the total magnetite content of the slag and the amount of magnetite which may be considered to be in solution. It is not true that the lowest melting converter slag is that corresponding to the eutectic between ferrous oxide and silica. The simplest slag system which can be considered is a three-component system, since both ferric and ferrous iron are present. As Schuhmann, Powell, and Michal have shown, there are lower melting compositions than this eutectic in the ternary system. The most unfortunate impression given by this paper is that the driving force for chemical reaction is determined by the heat of reaction: of course the entropy change must be taken into account. It would have been more correct to list, in Table VI, values for free energies of formation. Nor can it be said that the data in Table VI represent the "best available data." They do not corregtond with any of the recent, acknowledged sources. F. E. Lathe and L. Hodnett(author's reply)— We are pleased that Dr. King finds the factual information in our uawer of some interest. Dr. King suggests that it would have been better if our analysis and discussion of the data had been omitted, largely because our list of references is so. incomplete. If he will carefully read our introduction, he will see that the questionnaire was sent out in the hope of obtaining data which would throw light on certain questions relating to the use of converter refractories. We did not attempt (nor would the AIME have published!) a complete review of the literature on copper converting, as Dr. King has apparently assumed, nor indeed a complete analysis of the data submitted, but tried only to find a sound basis for the choice of refractories, taking into consideration common variations in converter practice. We hope our paper indicates that, by raising the silica content of the converter slag and operating at a higher temperature, the normal circulating load of magnetite can be greatly reduced, and the whole reverberatory-converter operation improved to a major degree, with resultant important savings. Under such operating conditions, chrome-magnesite brick may be expected to stand up better than those of straight magnesite. Regardless of the choice as between these brick types, however, we find the cost of converter refractories to be so low in comparison with other converter costs as to justify operation under the more severe conditions suggested. Valuable as are the papers by Schuhmann and associates and the book by Ruddle, we make no apology for omitting reference to them, nor for using heats of reaction without mention of entropy changes or free energies of formation. Our primary object was to interest the practicing copper metallurgist, with whose language we may claim to be fairly familiar; we think it would have been unwise to include the highly theoretical phases of the subject which Dr. King suggests. The interest shown in our preliminary paper presented at the New York meeting in 1956, and the trends in practice whtat we have observed since that time, suggest that we did not wholly miss the target. In conclusion, we sincerely hope that Professors King and Schuhmann will independently review the data obtained in our questionnaire and submit a paper giving their own recommendations as to the choice of refractories and the particular converter operating conditions which will result in the lowest overall cost of copper smelting and converting.

Jan 1, 1960

By Magnus Troilius

SINCE the discussion on steel rails in America has forcibly drawn attention to the value of chemical analysis, if not as a necessary stipulation, at least as a guide to control the usual mechanical tests, some doubt has been thrown upon the accuracy of the analytical results obtained by different chemists. To any one having the least acquaintance with chemistry, it is quite clear that if exactly similar results are to be obtained from the same borings of steel, exactly the same methods must be used by the different analysts. Hence the necessity (if complications are to be avoided) of establishing what I may call standard or normal methods, to be used both by the inspectors and by the chemists at the works. Remembering that the application of chemistry to steelrail inspection is yet in its infancy, it is of great importance to possess a perfect acquaintance with the best methods in use. Being myself a grateful pupil of Professor Eggertz, of the School of Mines in Sweden, it occurred to me, two years ago, that I could not do better than start a laboratory of my own, and engage one of his pupils, Mr. Troilius, for the purpose of analyzing the steel borings from mechanically-tested rails, so that I might thus obtain without delay thoroughly accurate determinations. Moreover, in order to carry on the operations in perfect accordance with the methods used at the steel works in England and Germany, where I had to control the manufacture, I deemed it desirable to allow Mr. Troilius to go through a course of training at these works; and I gladly seize this opportunity of expressing my grateful acknowledgments to several works in England and in Germany for affording every facility for such an exchange of information as mas found necessary in arriving at the best analytical methods to be used.

Jan 1, 1882

By E. T. Turkdogan, W. L. Worrell

The rate of reaction of hydrogen sulfide with ferrous sulfide was studied by measuring the initial rates of sulfidation of iron strips in hydrogen sulfide-hydrogen-argon mixtures at 670°, 800°, and 900" C. The time-dependent surface sulfur activity is derived from the instantaneous rate of sulfidation with the assumption that diffusion in the sulfide layer is in a pseudo-steady state with the gas-sulfide chemical reaction. The rate of sulfur transfer from hydrogen sulfide to the surface of iron sulfide is proportional to the partial pressure of hydrogen sulfide and inversely proportional to the activity of sulfur at the surface of the sulfide layer. The derived rate equation is based on the assumption that most of the surface sites on the chemisorbed layer of iron sulfide are occupied by sulfur atoms and that the slow rate-controlling reaction is the dissociation of hydrogen sulfide on the chemisorbed layer. The experimental results are in reasonable accord with this reaction model. 1 HE slow approach to parabolic growth rate in the sulfidation of iron in hydrogen sulfide-hydrogen mixtures is a manifestation of slow approach to surface equilibrium between the gas and the surface of the sulfide layer. For example, at 800°C and Fig. 7 in Part I, the parabolic growth rate begins after approximately 1 day of sulfidation time. With decreasing temperature and decreasing partial pressure of hydrogen sulfide, the time necessary to reach gas-sulfide surface equilibrium is much longer. These observations are similar to those reported previously by Turkdogan et al.' on the oxidation of iron to wustite in hydrogen-water vapor mixtures. The slow approach to gas-sulfide equilibrium is well-demonstrated by the results in Fig. 1 where the square of the weight gain per unit area, ( g S per sq cmI2, is plotted against time for gas mixtures having PH g//>H = 1.0 with 0, 25, 50, and 67 pct Ar at 800°C. The value of 1.5 X lo-' (g S per sq cm)' corresponds to almost complete sulfidation of the iron strip (- 0.05 cm thick) to iron sulfide. The points fall on S-shaped curves. If the inflection parts of the curves are considered to be linear, thus indicating parabolic growth rate and the establishment of gas-sulfide equilibrium, their slopes would have to be the same for a fixed ratio in the gas mixture. Such is not the case, and the slopes for the "linear" parts of the S-shaped curves are lower than the value when gas-sulfide surface equilibrium is established. The subject matter of this paper is the kinetics of the surface reaction of hydrogen sulfide with iron sulfide during the early stages of sulfidation of an iron strip. EXPERIMENTAL RESULTS The apparatus and materials used were the same as those discussed in Part I. In the present experiments of relatively short duration, a purified iron strip, 5 by 2 by 0.05 cm, which was suspended in the uniform hot zone of a vertical zircon tube, reacted with a flowing gas mixture of hydrogen sulfide-hydrogen-argon. The sample was suspended from a gold chain attached to a calibrated silica spring. The amount of sulfur picked up by the iron, which formed a layer of iron sulfide, was determined by measuring the displacement of a reference point on the silica spring, using a cathetom-eter. In all cases, the degreased sample was first annealed in a stream of oxygen-free dry hydrogen for several hours to remove any impurities such as oxygen, nitrogen, or carbon which might have been present on the surface of the sample.' The rate measurements were carried out at 670°, 800°, and 900° C in hydrogen sulfide-hydrogen-argon mixtures with pH2 s/Ph2 ratios from 4 to 0.1. In a few experiments of short duration no sulfur deposition was observed in gas mixtures with (comments concerning sulfur deposition at high pH s/ph ratios were made in Part I.) Typical examples of the results obtained are shown in Fig. 2 for two temperatures and two gas compositions. With the present experimental technique, reproducible rate data could be obtained only after a uniform

Jan 1, 1969

By Leslie W. Austen

ROTARY kiln operators will agree that some of the most severe conditions a refractory must stand occur in the hot zone of a kiln burning Portland cement, dead burn dolomite, magnesite, peri-clase, and similar materials. Frequently the operator is faced with factors beyond his control which drastically shorten the life of refractories. Shutdown due to mechanical failure can be serious if the period is of sufficiently long duration to cause the dropping of coating or the loosening of the lining. A change in slurry can affect the coating and cause ring buildup. A change in type of fuel and its effect upon the flame can cause a shift in location of the hottest zone. Weekend shutdowns or any other interruption can cause the operator trouble and may damage the refractories, since stopping and starting a rotary kiln is certainly more difficult than stopping and starting a motor. Some operators have tried to set an estimate of damage for each shutdown in equivalent days of running time. Conditions affecting the refractory may be roughly grouped in four classes: chemical attack, mechanical stress, thermal shock, and abrasion. Chemical Attack: The drive to obtain maximum production through a kiln demands maximum operating temperatures, temperatures which are limited more by the ringing up or melting of the clinker. This can cause interface temperatures at the junction of coating and refractory which require the use of a basic kiln block to withstand the chemical attack. Chemical changes take place within the refractory itself, especially in chemically bonded or unburned kiln blocks. These changes cause the formation of the ceramic or burned bond. Migrating liquids or fluxes from the kiln charge have an effect within the refractory and lead to mineral or glass formation. The alkalies, sodium and potassium, migrate into the refractory as silicates, chlorides, sulphates or other salts. They may move under capillary action or may be caused to move by volatilization with condensation in the cooler portion. Mechanical Stress: Concentrated stress may be caused by several factors or combinations thereof. I—The rings of refractories must be kept tight and rigid within the kiln, and this alone demands considerable force to hold the blocks in place. So that the force will not be concentrated, the blocks should fit the circle as perfectly as possible, with the faces in contact overall. 2—As the kiln is heated, thermal expansion takes place at the hot end of the kiln block. Since this disturbs the plane face it too can cause a concentrated stress at the two ends of the block, and shearing stress can be set up within the brick itself because of the difference in expansion between the two ends. 3—If a lining becomes loose and moves in the shell very severe stress can be set up, and as the kiln rotates this load changes and gives the effect of repeated loading. Permanent expansion of the refractory can also cause severe loading. 4—Not least important, flexing of the kiln is frequently the cause of concentrated stresses. Thermal Shock: Thermal shock, the result of heating and cooling too rapidly, occurs on starting and stopping or when a large patch of coating drops, exposing the bricks. Again, its destructive effect is often the result of phase change, liquid to solid or the reverse; dense refractories loaded with glass-forming impurities are particularly susceptible. Thermal shock is a. problem with refractories set in the wall or roof of a stationary furnace, and becomes even more serious in a rotary kiln, the tendency to spa11 being magnified with movement and concentration of stress. Uniform rate of feed and loading insures both better coating and a more uniform stress. Abrasion: If the refractories do not take a coating, abrasion can become a most destructive factor. Movement of the lining in shell or movement of loose blocks causes abrasion, which is also most destructive if the refractories do not take a coating. An analysis of the problem of basic lining for the hot zone reveals, therefore, a number of desirable characteristics: high refractoriness, basic chemical reaction, resistance to spalling, good strength at all stages, ability to take coating, true sizing, volume stability, and abrasion resistance. Increased demand

Jan 1, 1953

By Leslie W. Austen

ROTARY kiln operators will agree that some of the most severe conditions a refractory must stand occur in the hot zone of a kiln burning Portland cement, dead burn dolomite, magnesite, peri-clase, and similar materials. Frequently the operator is faced with factors beyond his control which drastically shorten the life of refractories. Shutdown due to mechanical failure can be serious if the period is of sufficiently long duration to cause the dropping of coating or the loosening of the lining. A change in slurry can affect the coating and cause ring buildup. A change in type of fuel and its effect upon the flame can cause a shift in location of the hottest zone. Weekend shutdowns or any other interruption can cause the operator trouble and may damage the refractories, since stopping and starting a rotary kiln is certainly more difficult than stopping and starting a motor. Some operators have tried to set an estimate of damage for each shutdown in equivalent days of running time. Conditions affecting the refractory may be roughly grouped in four classes: chemical attack, mechanical stress, thermal shock, and abrasion. Chemical Attack: The drive to obtain maximum production through a kiln demands maximum operating temperatures, temperatures which are limited more by the ringing up or melting of the clinker. This can cause interface temperatures at the junction of coating and refractory which require the use of a basic kiln block to withstand the chemical attack. Chemical changes take place within the refractory itself, especially in chemically bonded or unburned kiln blocks. These changes cause the formation of the ceramic or burned bond. Migrating liquids or fluxes from the kiln charge have an effect within the refractory and lead to mineral or glass formation. The alkalies, sodium and potassium, migrate into the refractory as silicates, chlorides, sulphates or other salts. They may move under capillary action or may be caused to move by volatilization with condensation in the cooler portion. Mechanical Stress: Concentrated stress may be caused by several factors or combinations thereof. I—The rings of refractories must be kept tight and rigid within the kiln, and this alone demands considerable force to hold the blocks in place. So that the force will not be concentrated, the blocks should fit the circle as perfectly as possible, with the faces in contact overall. 2—As the kiln is heated, thermal expansion takes place at the hot end of the kiln block. Since this disturbs the plane face it too can cause a concentrated stress at the two ends of the block, and shearing stress can be set up within the brick itself because of the difference in expansion between the two ends. 3—If a lining becomes loose and moves in the shell very severe stress can be set up, and as the kiln rotates this load changes and gives the effect of repeated loading. Permanent expansion of the refractory can also cause severe loading. 4—Not least important, flexing of the kiln is frequently the cause of concentrated stresses. Thermal Shock: Thermal shock, the result of heating and cooling too rapidly, occurs on starting and stopping or when a large patch of coating drops, exposing the bricks. Again, its destructive effect is often the result of phase change, liquid to solid or the reverse; dense refractories loaded with glass-forming impurities are particularly susceptible. Thermal shock is a. problem with refractories set in the wall or roof of a stationary furnace, and becomes even more serious in a rotary kiln, the tendency to spa11 being magnified with movement and concentration of stress. Uniform rate of feed and loading insures both better coating and a more uniform stress. Abrasion: If the refractories do not take a coating, abrasion can become a most destructive factor. Movement of the lining in shell or movement of loose blocks causes abrasion, which is also most destructive if the refractories do not take a coating. An analysis of the problem of basic lining for the hot zone reveals, therefore, a number of desirable characteristics: high refractoriness, basic chemical reaction, resistance to spalling, good strength at all stages, ability to take coating, true sizing, volume stability, and abrasion resistance. Increased demand

Jan 1, 1953

By AIME AIME

Do you Possess, or Can you Obtain; and Will you Give, or Sell, to the Institute Library Early Volumes of the following Proceedings and Journals? American Chemical Society. American Foundrymen's Association. Australian Mining Standard. Chemical Society of London. Deutsche Chemische Gesellschaft. The Foundry. New Zealand Mines Record. Queensland Government Mining Journal. La Revue Universelle des Mines.

Jan 9, 1907

By W. C. Winegard, C. J. Beinjessner

PREVIOUS investigations 1,2 of Fe3P described by pearson3 and schubert4 show that Fe3P has a bct unit cell having four Fe3P tetrahedra centered around each lattice point. The space group is 14, No. 82, and all atoms occupy general positions 8(g). The cell dimensions3 are: a = 9.090, c = 4.446 kX, with an axial ratio of c/o = 0.4891. We have measured the lattice parameters of Fe3P, using a Fe as an internal temperature standard, at 23°, 414°, and 678°C and computed the thermal expansion over this temperature range. The Fe,P was prepared by melting under vacuum (after flushing with argon) a commercially pure iron and "ferrophosphor" in a high-frequency induction furnace. Part of the ingot was crushed for X-ray examination and for chemical analysis. X-ray diffraction and light microscopy indicated iron phosphide (Fe3P) present as the major constituent and a small amount (about 5 pct) of a Fe. Chemical analysis showed 0.05 wt pct Si, 0.008 wt pct N, 0.018 wt pet C, and less than 0.02 wt pct each of other metallic elements. X-ray diffraction powder patterns were obtained from a mixture of iron and Fe3P sealed in an evacuated quartz capsule using a Unicam high-temperature

Jan 1, 1968

By C. H. Jr. Herty

The results of a study of the open-hearth process from the physicochemical view-point are given. This study includes experimentation in small laboratory furnaces and in standard 100-ton furnaces. The behavior of manganese, carbon, and phosphorus are quantitatively explained. The action of "residual" manganese is discussed with reference to its relation to iron oxide dissolved in the metal. The solubility of CO in steel and its relation to dissolved FeO and carbon is given. The equation for phosphorus elimination has been tested out on a 200-ton furnace and the results are given in the text. THE effect of temperature and slag composition on the elimination of metalloids in the basic open-hearth process has been qualitatively understood since the early days of steel making. The quantitative effect has, however, only recently been brought to attention. The effect of slag composition has received more attention than that of temperature, primarily because the range of finishing temperatures in the basic open-hearth process is small compared to the large variations found in the composition of the slag at different periods during the process, and to the variations occurring with the use of raw materials of different degrees of impurity. The effect of slag composition on the elimination of metalloids has been studied by Styri1 from the thermochemical standpoint. This method is open to serious errors, in that thermochemical data at 2900° F. are very inaccurate and in many cases completely lacking. Feild2 has calculated equilibrium constants from the rate at which the metalloids are eliminated. The effect of slag viscosity on rate of elimination will affect the constants calculated by this method. Whitely,3 Colcough4 and others have used slag compositions as the basis for calculation of constants by which the extent of elimination may be calculated.

Jan 2, 1926

By Howard Martens, Pol Duwez

IN two papers published in 1949, alloys of chromium with the refractory metals tungsten, molybdenum, tantalum, and columbium were investigated in view of their possible use as high temperature resisting materials. For the Cr-Ta system, a partial phase diagram was presented and the only intermediate phase was identified at Ta2Cr3. A phase of the same composition was also observed in the Cb-Cr system. The X-ray diffraction data presented in these papers, however, were insufficient for crystal structure determination. It is shown in the present study that the only intermediate phase in both the Ta-Cr and the Cb-Cr systems corresponds to the ideal stoichiometric ratio TaCr2, or CbCr2. Both structures are cubic, MgCu, type. At high temperature, however, TaCr2 has a hexagonal MgZn, type structure, which can be retained at room temperature by fast cooling. The alloys were prepared by melting in a helium arc furnace on a water-cooled plate. The design of the furnace was essentially the same as that described in ref. 3. Some alloys were also obtained by sintering compacts made of the mixed powders pressed at 80,000 psi. The sintering was carried on for 4 hr at 1375°C. The tantalum and columbium powders were supplied by Fansteel Metallurgical Corp., North Chicago, 111. The tantalum powder was the reagent grade, with a particle size smaller than 400 mesh and a total impurity content less than 0.1 pct. The columbium powder was smaller than 325 mesh and contained approximately 0.1 pct C and traces of Fe, Ti, and Zr. The electrolytic chromium powder from Charles Hardy, Inc., New York, was smaller than 300 mesh and contained about 0.1 pct Na, 0.05 pct Ca, and traces of Cu, Al, Mg, Si, and Co. Powder diffraction patterns were obtained with a 14.32 cm camera, using copper Ka radiation filtered through nickel foil. The powder pattern of the TaCr2 alloy obtained by sintering at 1375'C was different from that obtained on the same alloy rapidly cooled from the melt. Contrary to this result, the powder pattern of CbCr2 was the same, whether the alloy was made by sintering at 1375°C or by melting, and was similar to that of the TaCr, sintered. It was also found that the structure of the TaCr2 specimen obtained by melting was retained after heating for 4 hr at 1590°C, but transformed into the structure found in the sintered specimen after heating for 4 hr at 1375°C. Hence, the structural change of TaCr2, appears to be a reversible polymorphic transformation. CbCr2 and ToCr2 Structure, Low Temperature Form By using large scale Hull-Davey charts, the powder pattern of CbCr, and of the low temperature form of TaCr2 were readily interpreted on the basis of a face-centered cubic lattice with a parameter of approximately 6.95 kX. The indices of the reflections together with the values of sin' 0 are given in Tables I and 11. From this list of observed reflections, it appears that the (200), (600), (024), (046), and (028) reflections are missing. The lack of (h00) reflections for h 4n indicates a four-fold screw axis. The missing (Okl) spectra for k + 1 An indicate the existence of a diamond glide d. The combination of these symmetry elements can be found in the O— Fd3m space group, which is therefore the most probable one. After having determined the approximate density of TaCr, by the immersion method, the number of molecules per unit cell was calculated and found to be nearly eight. This information, added to the fact that the most probable space group is O leads to the consideration of a structure of the MgCu2 type, in which the atoms have the following positions: 8 magnesium in a and 16 copper in d. On the basis of this structure, intensities were computed by means of the usual formula: 1 cos'20 I a sin2 cos where F is the structure factor; 8, the Bragg angle: and p, the multiplicity factor. As shown in Tables I

Jan 1, 1953

By D. S. Jacobus

The boiler here referred to was of the water-tube type, having 2535 square feet of heating-surface, which the makers held to be capable of generating 325 horse-power of steam; this being understood to mean that 325 times 30 pounds of water would be evap-

Jan 1, 1889

By Edward V. D’Invilliers

In connection with some recent professional work in the coalfields of Western Pennsylvania, with special reference to results of coking operations, I was asked to compile a statement giving the estimated cost of mining coal and manufacturing coke at two hypothetical plants of 500 ovens each, giving the relative yield of coal in coke at each plant; and, upon the average number of working days in each of the past five years, from 1899 to 1903, together with average selling price of coke at the ovens, to prepare an estimate of the relative commercial returns in each district. What seemed at first sight to be a comparatively simple proposition, involving only the ordinary elements of mining and coking costs, became complicated by the lack of standard published records of mining costs and sales, which would be applicable to the subject at issue. Upon searching through the usual channels of Government publicatious and the files of our technical societies and mining periodicals, I was surprised to note the absence of fundamental factors that would approximately meet the case in point. The very elaborate and interesting statistics annually published by the National Government' do not supply the required data for the following reasons:—1. Being reported by arbitrary districts, the average values are too general to be applied to special fields. 2. The value of coal charged to the ovens is apparently based upon the regional average value of the coal if sold in the market, and not upon the cost of production. 3. Some plants only use the slack (a by-

Jan 1, 1905

ANDES, lying south of Chuquicamata and north of Braden on the western slope of Chile's cordillera, can best be described as a big well-managed copper-mining enterprise without any peculiarly outstanding features. In point of copper produced, since output started in 1927, it ranks fifth among the Porphyries, being exceeded only by its two Chilean contemporaries and by Utah Copper and Morenci in the United States. Even so, there is little to distinguish it from other properties. It does not have the phenomenally rich ore (better than 2 per cent copper) that characterizes Braden; and it is not in the same class as Chuquicamata whose ore has the excellent tenor of around 1.7 per cent, nor has it Chuqui's immense tonnage of proven ore reserves and potential ore resources. One might say the operations are standard in that there are no basic or radical departures from established practice. A letter from New York supplying me with sundry pertinent facts for which I had asked, makes this comment regarding the answer to one inquiry: "omitted because it is the ordinary equipment found in any well-run mine." The substance of that remark applies generally to the other operations, plants, and facilities. One interesting fact that helps explain this situation should not be overlooked. Until the "new" Morenci in 1942, Andes was the last of the Porphyry copper mines to come into production. It did not do much pioneering because other companies had, of necessity, charted the way in many particulars. The company was organized by the Anaconda Copper interests in 1916 to take over a, group of claims held under option by William Braden who, a few years earlier, had interested

Jan 1, 1957

By H. R. Page, A. E. Jr Lee

From the inception of zinc retorting on a commercial scale in the United States in 1890,' the retort employed has undergone wide variations in its composition and manufacture, facilitating in part equally remarkable improvements in furnace capacities. The early day hand made clay retort was charged with carbonates or silicates or with coarse dead roasted concentrates mixed with a large proportion of charge fuel resulting in a relatively low zinc burden and fired 24 hr in direct coal fired furnaces. Its modern counterpart is fabricated in hydraulic presses from clay mixtures containing sizeable amounts of either silicon carbide or silica flour, charged with sintered flotation concentrates to more than three times the early day zinc burden and fired 24 to 48 hr in gas fired furnaces. This paper does not attempt to describe in detail the early day clay retort practice as it is well outlined in treatises by Ingalls,2 Lodin,3 Liehig,4 Hofman5 and others. A brief review of clay retort practice is presented together with a description of the major developments since 1912. Clay Retorts The Belgian type retort, both in the circular and elliptical forms, has been used almost exclusively. Typical dimensions of press made clay retorts around 1910 are shown in Table 1. Variations in these dimensions were used at different plants according to local conditions to a maximum inside diameter of 9 in. and inside length of 54 in. However, the effective heat penetration in a 24 hr firing cycle and the tendency of the retort to bend limited the retort size. Use of the elliptical vessel was an attempt to present a stronger cross-section resisting the tendency to bend and to increase the burden without increasing the depth of heat penetration. One exception to the 48-54 in. length was the 60 in. retort used as early as 1905 at Palmerton by means of supporting the last 12 in. at the butt end with a specially designed furnace back-wall. This backwall construction with the 60 in. retort had been developed and used at Bethlehem by G. G. Con-vers and A. B. DeSaulles. An attempt was made at Blende, Colo. to use even larger retorts of the Rhenish type based on European practice and requiring much higher furnace temperatures. Satisfactory plastic clays capable of withstanding these temperatures were not available, and the plant never operated successfully. PREPARATION OF BATCH Composition of the clay retort by weight was 40 to 50 pct raw clay and the balance "grog." Generally speaking the mix consisted of 7 parts plastic clay to 9 parts grog by volume. Principal source of the clay used was the Cheltenham vein—sometimes referred to as "St. Louis city clay." A typical analysis was A12O3-31.0 pct, SiO2-50.0 pct, Fe2O3-2.5 pct, MgO-0.3 pct, CaO-1.5 pct and loss on ignition 14.0 pct. At the smelter the clay was weathered whenever possible and then crushed to 0.08 in. or finer. Grog consisted of calcined adobies, cleaned retort scrap and cleaned refuse fire brick such as old furnace brick, blast furnace linings, and others. Saggers from ceramic plants and calcined flint clay were later used. The grog materials were ground to 0.12 m. or finer. Occasionally coke dust up to 10 pct of the mix was substituted for a part of the grog following European practice.² Particle size of the grog has a major influence on the retort properties—the larger the grain, the better can the retort withstand thermal shocks, resist bending at furnace temperatures and resist corrosion from slag; the smaller the grain, the lower the loss of zinc vapor through the retort walls. Grog forms the skeleton of the retort, and the clay shrinks around its grains to act as a binder. In the drying process, the grog has a stabilizing effect on the drying rate, decreasing shrinkage and giving up previously absorbed water to the surrounding clay to minimize the danger of cracking or checking.² Grog and clay were mixed through a horizontal pug mill with 10 to 20 pct water added, depending on whether the retort was to be formed by hand or mechanically, more water being required for the hand process. The batch or "mud" extruded from the pug mill was cut in convenient lengths for handling, stacked in piles or in special rooms, covered with wet burlap and allowed to "rot" or age from 1 to 8 weeks to increase plasticity. HAND MOLDING If the retort was to be molded by hand, the mud was repugged after the rotting period and given to the molders. Their molds consisted of 3 sheet iron or wood cylinders, each one third the retort length and defining the outer shape of the retort. Beginning with the bottom section, mud was placed in the form and tamped with a rammer

Jan 1, 1950

By C. R. Schumacher, W. H. Moyer

Cornwall, Pa. magnetite ore, containing recoverable sulfides in the form of chalcopyrite and pyrite, has been mined continuously since 1742 1 Beneficiation of the ore was begun in 1905, at the Lebanon concentrator located six miles from the mine. At first, only magnetite was recovered, using Grondal magnetic separators. In 1907, copper minerals were recovered by means of Wilfley tables. Copper flotation, attempted as early as 1912, was finally successful in 1919. In 1940, flotation of the cobalt- bearing pyrite was begun, and Cornwall ore became the major domestic source of cobait for many years. In 1916, the Bethlehem Steel Corp. began to purchase interests in the Cornwall mine and Lebanon concentrator properties, and by 1926 had acquired complete ownership. Metallurgical practice at the old Lebanon concentrator was good, but by today's standards the plant was outdated. The flowsheet was complex, due both to the mineral content of the ore and to the low capacities of much of the equipment. As the flowsheet developed, buildings were added and the plant was spread over a relatively large area, with resulting high manpower requirements. Another disadvantage was the six-mile rail haul from the mine to the Lebanon concentrator.

Jan 3, 1966

By C. H. Herty

The results of a study of the open-hearth process from the physicochemical viewpoint are given. This study includes experimentation in small laboratory furnaces and in standard 100-ton furnaces. The behavior of manganese, carbon and phosphorus are quantitatively explained. The action of "residual" manganese is discussed with reference to its relation to iron oxide dissolved in the metal. The solubility of CO in steel and its relation to dissolved FeO and carbon is given. The equation for phosphorus elimination has been tested out on a 200-ton furnace and the results are given in the text. The effect of temperature and slag composition on the elimination of metalloids in the basic open-hearth process has been qualitatively understood since the early days of steel making. The quantitative effect has, however, only recently been brought to attention. The effect of slag composition has received more attention than that of temperature, primarily because the range of finishing temperatures in the basic open-hearth process is small compared to the large variations found in the composition of the slag at different periods during the process, and to the variations occurring with the use of raw materials of different degrees of impurity. The effect of slag composition on the elimination of metalloids has been studied by Styril from the thermochemical standpoint. This method is open to serious errors, in that thermochemical data at 2900' F. are very inaccurate and in many cases completely lacking. Feild2 has calculated equilibrium constants from the rate at which the metalloids are eliminated. The effect of slag viscosity on rate of elimination will affect the constants calculated by this method. Whitely,a Colcough4 and others have used slag compositions as the basis for calculation of constants by which the extent of elimination may be calculated.

Jan 1, 1926

Body Hoists A complete new line of hydraulic dump truck body hoists and bodies featuring many outstanding design improvements has just been announced by St Paul Hydraulic Hoist Fourteen models of this new hoist are available in a selection of capacities from 6 to 25 tons The new body hoist features low standard mounting height, advanced lifting point, new low operating oil pres [ ] sures, a new Uniflex subframe, friction-free roller bearing drive mechanism, including pump and power takeoff, to insure quiet operation and long trouble-free life A stress-eliminating design feature of the new hoists absorbs dumping shocks and permits use of a new principle in hoist design a flexible subframe which ends tendency of rigid hoists to crack or bend when flexed Circle No. 1 Combination Drill A new combination drill offering all three methods rotary, auger, and percussion drilling on the same rig is the revolutionary feature of the latest drill rig designed by Mobile Drilling Inc The B-36 drill is larger, more powerful and versatile than previous models built by this company This new drill has a hydraulic feed of approximately 8000 lb pressure The hydraulic feed cylinder is located directly over the rotary turn table The carriage of the drill is of tubular construction The drill mast, also of tubular construction, nests in the tube members of the drill carriage for cross-country travel with a maximum overall height of 10 ft The drill mast telescopes together with the feed cylinder hydraulically to an operating height of 16 ft The drill can be furnished with an auxiliary cat head, sand reel, and special high pressure water pump The B-36 maximum depth for auger drilling without water is approximately 150 ft, depth for rotary drilling with water is in excess of 300 ft Circle No 2

Jan 1, 1952

By Richard Henry Lee

Since the economies in the blast furnace resulting from enriching iron ores are so great, much attention has been paid during the past few years to the various methods of concentrating lean ores, and, as the concentrated ore is usually of extreme fineness, various methods of agglomeration and sintering, of more or less value, have been put into operation. The resulting agglomerated concentrates are generally obtained in the form of briquettes or nodules. The briquettes naturally divide themselves into two classes: (1) those made by the mixture of some binding agent, and then formed into briquettes under great pressure; and (2) those made by sintering the concentrates, the latter either being formed into bricks before exposure to heat or the sintered mass broken into fragments afterward. Of the first class I will not speak, as they are not used on an extensive scale in this country. The second class of briquettes, or those made by sintering, are simply masses of melted or fused silicate and oxide of iron mingled with more or less silicates of aluminum, lime, and magnesia. The fact that the material in a briquette is sintered is proof positive that there are no pores in the material. There are, however, quite a number of holes of greater or less diameter through the gubstance of the briquette. They are not pores in the common acceptance of that term as applied to ores by furnacemen, as the ides of the holes and channels are fused. In reality the material is simply mill cinder. It is practically untouched by the gases in the upper part of the furnace, and the iron has to be reduced by solid carbon in the boshes and hearth. Briquettes sometimes show a little saving in fuel in the furnace over an ore mixture of large lumps, but that saving is made simply because, owing to the numerous holes and channels through the mass, the briquette is practically composed of numerous small or fine lumps, and, as is well known, the finer the

Jan 1, 1914

By C. Law McCabe, R. G. Hudson

The Knudsen cell has been employed to determine the free energy of formation of Mn7Cs in the temperature range 800" to 950°C. A value of 66,440 cal was found for hH°o for a-manganese. Measurements of the pressure of manganese over a mixed carbide, (Fe,Mn),C, points to a power relationship between aun7cs and N.4,. RECENTLY Kuo and Perssonl have reported that the carbide of manganese which is in equilibrium with graphite at temperatures up to 1100° C is Mn7Ca. There are no published data on the thermo-dynamic properties of this compound. In order to determine the stability of Mn7Ca, it appeared that, by obtaining the pressure of manganese above 8-manganese and also above Mn,C, in equilibrium with graphite, the free energy of formation of Mn7Ca from 8-manganese and graphite could be obtained. In addition, the vapor pressure of manganese, reported by Kelley From data of Bauer and Brunner,' is subject to some uncertainty and further determinations of the vapor pressure of manganese seemed warranted. In this investigation of the pressure of manganese vapor above pure manganese and also above the carbide of manganese in equilibrium with graphite the apparatus used is the Knudsen orifice cell. The same apparatus, experimental procedure, and method of calculating the pressure was used in this investigation as in one previously reported.~ Care was taken to insure that the cells were at constant weight before using them in a run. The manganese charged in the cell was CP grade powder, carbon free, obtained from the Fisher Scientific Co. A spectroscopic analysis of the manganese after appreciable amounts of it had vaporized from the Knudsen cell showed that no element was present in sufficient quantities to contribute to a weighable weight loss or to decrease the vapor pressure of manganese to any appreciable extent. The spectro-graphic analysis was 0.002 pct Cu, 0.05 pct Fe, 0.002 pct Pb, and 0.002 pct Ni. 8-manganesea is the allo-tropic form of manganese which was present in the cell at temperatures used in this investigation. The manganese carbide, Mn,Ca, was made in the following way: In a closed graphite cell manganese powder was added to graphite powder, which was made from graphite rods for spectrographic use. The manganese powder was the same as that described previously; 5 pct excess graphite was added over that required for the formation of Mn7C,. The mixture was heated in a closed graphite cell for approximately 20 hr at 1350°K under vacuum. X-ray analysis revealed that there was no manganese present after this treatment, but that the lines due to Mn,C, were present. In order to prove that there was no volatile carbide of manganese which was effusing out of the cell, the following experiment was performed: A graphite effusion cell containing graphite power, in excess of that to form Mn,C, of a desired amount, was brought to constant weight on heating at 1228°K. The required amount of manganese was accurately weighed and then added to the graphite effusion cell. The cell was placed in a vacuum at 1228°K for one week, which was the time calculated for the manganese to have effused completely, assuming instantaneous formation of Mn,C8. The cell was then weighed again. This experiment was carried out on two different occasions and both times the weight loss of the cell came within 1 pct of the weight of manganese originally charged minus the weight of manganese left in the cell, as determined by chemical analysis. These data are summarized in Table I. This agreement is considered to be within experimental error and is taken as proof that no carbide of manganese is volatile in this temperature range. It was established, by X-ray analysis, that Mn,C, formed before appreciable amounts of manganese vaporized from the metal powder which was charged. The identification of the carbide of manganese which was present in the Knudsen cell in equilibrium with graphite and manganese vapor was carried out by Kehsin Kuo at the University of Uppsala. He established that the authors' sample, which was submitted to him for analysis, contained the phase

Jan 1, 1958

By Richard Lee

SINCE the economics in the blast furnace resulting from enriching iron ores are so great, much attention, has been paid during the past few years to the various methods of concentrating lean ores, and, as the concentrated ore is usually of extreme fineness, various methods . of agglomeration and sintering, of more or less value, have been put 'into operation. The resulting agglomerated concentrates are generally obtained in the form of briquettes or nodules. The briquettes naturally divide themselves into two classes: (1) those made by the mixture of some binding agent, and then formed into briquettes under great pressure; and (2) those made by sintering the concentrates, the latter either being formed into bricks before exposure to heat or the sintered mass broken into fragments afterward. Of the first class I will not speak, as they are not used on an extensive scale in this country. The second class of briquettes, or those made by sintering, are simply masses of melted or fused silicate and oxide of iron mingled with more or less silicates of aluminum, lime, and magnesia. The fact that the material in a briquette is sintered is proof positive that there are no pores in the material. There are, however, quite a number of holes of greater or less diameter through the substance of the briquette. They are not pores in the common acceptance of that term as applied to ores by furnacemen, as the sides of the holes and channels are fused. In reality the material is simply mill cinder. It is practically untouched by the gases in the upper part of the furnace, and the iron has to be reduced by solid carbon in the boshes and hearth. Briquettes sometimes show a little saving in fuel in the furnace over an ore mixture of large lumps, but that saving is made simply because, owing to the numerous holes and channels through the mass, the briquette is practically composed of numerous small or fine lumps, and, as is well known, the finer the

Jan 10, 1913