Search Documents

By William Fink

THE constitution of the aluminum-cobalt alloys has been the subject of relatively few investigations. Brunck1 analyzed the residue which remained after treating the 17 per cent cobalt alloy with dilute hydrochloric acid. The results of the analyses indicated the existence of a compound Co3Al13. Guillet2 published a liquidus for the aluminum-cobalt system which contained two maxima corresponding to CoAl6 and CoAl2 and two eutectic points at 30 and 74 per cent Co. The most extensive investigation of the system was carried out by Gwyer,3 whose results are summarized in Fig. 1. It will be noted that at the aluminum end there is a suppressed eutectic at 644° C. By extrapolation of the duration of the eutectic arrest to zero, the composition of the compound was placed at Co3Al13. Another thermal arrest was noted at 550° C., which Gwyer attributed to a peritectic reaction. The present investigation of the aluminum end of the aluminum-cobalt system is the eleventh of a series dealing with the constitution of aluminum; rich alloys prepared from electrolytically refined aluminum.4 Preparation of Alloys.-The alloys used in this work were all prepared from electrolytically refined aluminum, the analysis of which is shown in Table 1. In preparing some of the alloys, metallic cobalt (98 to 99 per cent) was used either directly or in the form of an intermediate alloy, the composition of which is given in Table 1. In order to obtain alloys of higher purity, cobalt was introduced into some of the alloys by means of chemically pure cobaltous chloride which was readily reduced by the aluminum. A small electric furnace with nickel-chromium heating elements was used in the preparation of the alloys.

Jan 1, 1932

By D. Roberts

SUMMARY In order to accommodate a new plant in a limestone quarry in the Mendip Hills, it became necessary to excavate a potentially unstable disused face of the quarry. A simple two-dimensional graphical method was used to analyse a failure, which occurred during a period of exceptionally heavy rain in 1968, and the results of this analysis were used in estimating the stability of the proposed excavation. The presence of water in vertical fissures and tension cracks was found to be a dominant factor in determining the stability of these faces. The results of this approximate analysis were used as a guide in deciding upon the final slope design and the purpose of presenting this example is to illustrate how the various factors involved in arriving at this design were weighed to arrive at a compromise between theoretical recommendations and practical considerations. INTRODUCTION The successful outcome of a geological and geochemical survey to prove adequate re- serves of high quality limestone, suitable for producing burnt lime, led to planning for the installation of the necessary plant at Amalgamated Roadstone Corporation's Batts Combe Quarry at Cheddar in Somerset. Topographic and property boundary limits added to restrictions which were likely to be imposed by any forthcoming planning consents and restricted the choice of plant location to one site. The particular site is, in fact, the main floor area of the original quarry which, like many hillside quarries, had been worked with just one face. Before a benching scheme had been introduced on higher ground, the original face had attained a height of 230 ft. and sloped at angles of 58º to 64º. Fig. I shows the present configuration of the disused quarry face and the present working area above. The floor area below the disused face accommodates the existing crushing, conveying, and screening plant. The new facilities for lime burning are to be in addition to the existing main line business of producing roadstone and concrete aggregates and, although a new aggregate production plant would be included in the new installation, no disturbance of current production was to be contemplated.

Jan 1, 1972

By James F. Kemp

In earlier gears, the custom prevailed of regarding the anthracite basins as cases of folding with slight development of faulting. Folding is so pronounced and, in the eastern and western Middle Fields, at times so violent, that the inference was a natural one and led to the widespread impression that practically all the disturbances of the seams could be explained in this way. The cross-sections and maps prepared forty or more years ago for the Second Geological Survey of P ennsylvania, by Mr. Ashburner under Prof. J. P. Lesley, exhibit little else than folds.' So far as I can discover faults fail in the charts, except in one small case in the Henry colliery near Plainsville on the outskirts of Wilkes-Barre. Some years ago, while spending a day or two in Wilkes-Barr, under the guidance of R. V. Norris, I looked over some recent and accurate cross-sections of a numbcr of the large collieries and was deeply impressed with the peculiar behavior of some of the seams and the intervening shales. Thus, a seam might present a small, more or less overturned fold, rising 30 to 50 ft. (9 to 15m.) above its general course, and yet the movement would be taken up in the overlying shales, so as hardly to be noticeable in the seams next above or below. These and similar anomalies, especially when shown with the accuracy of engineer's surveys, possess great scientific and practical interest, bearing as they do, not alone on coal mining, but on theoretical geology and the actual behavior of strata under great compressive stresses. In preparation for the semicentennial meeting of the Institute, an effort was therefore made to secure some of the most interesting sections for presentation to the members. The collection of illustrations here shown is mainly due to Douglas Bunting of the local committee, to whom and to the contributing companies acknowledgments are due. The illustrations are taken from all four of the main basins, but are chiefly from the portions nearest Wilkes-Barre. The first are in the

Jan 1, 1922

By T. S. Lundy, C. J. McHargue

HE diffusion rate of v48 in single crystals of bee vanadium has been determined at temperatures from 1002° to 1888°C. Standard techniques of lathe sectioning were used for specimens annealed above 1500°C while sectioning by grinding was used for specimens annealed at lower temperatures. As will be seen, the lower-temperature data is enhanced on an Arrhenius-type plot relative to values expected by extrapolation of the high-temperature data. Single crystals were obtained from Linde Co. In Table I the analysis supplied by the vendor is compared with an analysis at Oak Ridge National Laboratory of a sample after a diffusion anneal. The isotope v4' was prepared by the Isotopes Division of Oak Ridge National Laboratory. Proton bombardment of a titanium target in the 86-Inch ORNL Cyclotron was followed by a carrier-free chemical separation. Nineteen specimens, 1/2 in. diam and 3/8 in. long, were cut from the as-received vanadium single crystals. Each specimen was machined with the flat face perpendicular to the longitudinal axis. Specimens were polished through 1/0 emery paper and were etched with 25 pct HF-10 pct H2SO4-10 pct HNO3-55 pct H2O. The polishing and etching steps were repeated until a satisfactory surface finish was achieved. The isotope was electroplated onto the specimens from a neutral solution. Counting rates of the deposited layers were approximately 100 counts per sec. At temperatures above 1200°C specimens were annealed in a tantalum resistance furnace under an argon atmosphere. Temperatures were measured with a Pyro micro-optical pyrometer and a Pt-Pt 10 pct Rh thermocouple. At lower temperatures the specimens were sealed in evacuated quartz ampoules and annealed in Kanthal wire-wound horizontal tube furnaces. A severe reaction occurred at 1200°C between the quartz and the vanadium. This

Jan 1, 1965

By Bryan J. Travis, Thomas L. Cook

INTRODUCTION Our growing concern for adequate and secure sources of energy and minerals has stimulated vigorous exploration for new sources, research toward a better understanding of geological processes, and development of new extraction technologies. The need for control, or at least prediction, of subsurface fluid flow is important for many of these technologies for example: primary, secondary and tertiary recovery of oil; ground water and waste management; in-situ fossil energy extraction (oil shale, coal, tar sands); and solution mining of uranium, copper and other minerals. These technologies, especially the last two, are characterized by highly complex systems. A partial list of the physical processes occurring would include flow in porous/fractured media, multi-phase and multi-component flow with heat transport, chemically active fluids and soils, tracers, diffusion and dispersion, fracturing and dissolution. A great deal of understanding of how these processes behave and interact can be obtained from models. MODELS Theoretical models are valuable because they: 1) provide a frame of reference for interpreting results of laboratory and field experiments; 2) once validated by experiments, allow a variety of geometries, injection/production strategies, etc., to be examined (at relatively low cost) for efficiency and stability; 3) can provide guidance to the design of experiments and field operations. Most models are based on the fundamental principles of mass, momentum and energy balance. But from this starting point, many paths can be taken. For example, there is the theory of Payatakes (1973) which concentrates on the microscale dynamics. In this approach, the rock or soil matrix is represented by a complex of characteristic channels (such as periodically constricted smooth tubes). Detail of flow within the characteristic channel is calculated very accurately. A difficulty with this model is that description of a representative channel can require several parameters which may not be easily measured. Also, it is not clear how the channels can be combined practically to model a large scale flow. Another type of model is the "global" one described by Bear (1972). Here, the continuum equations for conservation of mass, momentum and energy are averaged over a distribution of pore channels, resulting in a set of conservation equations in which the small scale structure of the medium is replaced by quantities such as porosity, permeability, dispersion coefficients and tortuosity. This approach allows computation of large scale flows. However, additional constitutive equations are needed which relate averaged quantities such as permeability to observables such as local saturation, particle size distributions, and others. An important difference between models is the way they handle the momentum equation. Payatakes' model solves the full equation. In others, it is replaced by a simpler relation such as Darcy's law (valid for slow flow rates) or by Forchheimer's equation which extends Darcy's law to higher flow rates. These simple relations can nevertheless match a great deal of experimental data (Dullien 1975). The permeability term which appears in Darcy's law and in Forchheimer's expression has been related to other quantities such as porosity and particle surface area. The Kozeny-Carmen equation is a well-known example, valid for some ranges of porosity and particle sizes and for some materials. Several other semi-theoretical, semi-empirical formulations have been devised, none of which are entirely satisfactory. One goal of researchers has been the ability to predict permeability of a porous material from basic measurable quantities such as grain size distributions without recourse to adjustable parameters. This effort has proceeded from consideration of distributions of idealized, non-intersecting channels, to intersecting channels, to consideration of both distributed pore radii and pore neck radii. This last approach has been used successfully to predict permeabilities (ranging over several orders of magnitude) in sandstones (Dullien 1975). Additionally, studies on explicit networks of channels (e.g., Fatt 1956) and percolation theory (e.g., Larson et. al. 1981) have been used to examine interconnectivity effects in porous media with the hope of eventually being able to predict permeability accurately. To be of more than theoretical interest, a model must be compared s controlled laboratory conditions where boundary and initial conditions and relevant material properties can be accurately determined. Also, extraneous forces can be eliminated so that the interactions between processes of interest can be clearly seen and flow models can be vigorously tested. In contrast to the well-defined environment and

Jan 1, 1982

By T. Sterry Hunt

THE essential principle of this new process, now in operation in Chili and in North Carolina, for the extraction of copper from its ores, is the dissolving of the oxides of copper by a hot solution of protochloride of iron and common salt. In the action which takes place, the protochloride of iron is converted into peroxide, while the oxides of copper are changed into protochloride and dichloride, the latter of which, though insoluble in water, is readily soluble in a hot strong brine. From the solution thus obtained, metallic iron throws down the copper in a metallic state, regenerating the protochloride of iron; which is then ready for the treatment of a fresh portion of oxidized copper ore. In the case of slimy ores, the contact of the bath with the ore is effected by agitation in tubs; but when the ores are granular, lixiviation in large vats is equally efficient and simpler. The hot solutions, charged with chlorides of copper, are digested in tanks with scrap-iron, or better, are made to flow through covered channels containing the scrap-iron, and in their passage lose the whole of their copper; the reaction at the same time evolving so much heat as to keep up the temperature of the liquid. In order to prevent a certain loss of chlorine, which otherwise takes place from the production of some basic ferric chloride in the reaction between the ferrous chloride and the oxides of copper (both protoxide and dinoxide being generally present in calcined ores), a portion of sulphurous fumes from the roasting is made to pass through the regenerated bath before adding it to fresh ore. This has hitherto been effected by injection, with the aid of a jet of steam.

By M. C. Manderson

Abstract-The sharp drop in world phosphate demand that took place in 1975, due to temporarily high prices, now seems to be reversing itself. And prices for both phosphate rock and phosphate fertilizers, which declined dramatically from their 1975 highs, now appear to be bottoming out. This recent price weakness has delayed new mining ventures that had previously been planned for completion by around 1980. While there is ample capacity to supply near-term rock needs, the stage seems to be emerging for a better supply-demand and price environment in the late 1970's and early 1980's.

Jan 1, 1978

By George M. Humphrey

It is indeed a pleasure for me to have this opportunity to discuss with you a subject which I find infinitely interesting and intriguing - namely, world-wide iron ore supply and demand. We will be examining the following: (i) current iron ore production and requirements; (ii) the major ore producing countries; (iii) the seaborne iron ore trade; (iv) ore grades or types; and (v) future requirements. For those who may not be familiar with the iron ore mining industry, it may be useful to know at the outset that our industry has been plagued with overcapacity for the past seven years. The optimism which prompted substantial expansion of productive capacity in the early to mid-1970's has unfortunately proved to have been unfounded. I shall begin by describing where we are today as well as a little about how we got there. In the latter regard, it's not so much that historical knowledge will solve any of the industry's problems or provide clairvoyance with regard to the future. Rather it's a feeling on my part that some knowledge of the past will provide a useful perspective capable of enhancing our analysis of future trends. At the time of writing, the most recent year for which we have definitive world-wide iron ore production and consumption statistics is 1980. In that year the world consumed approximately 859 million metric tons of iron ore to produce approximately 510 million metric tons of primary iron consisting of 502 million tons of pig iron and 8 million tons of sponge iron. Crude steel production for the same period attained a level of 719 million metric tons. Because it is possible in today's world to produce steel without consuming iron ore simply by melting scrap, the key statistic insofar as iron ore demand is concerned is primary iron production. In 1980 the ratio of iron ore consumption to primary iron production was 1.68:1.00. The comparable ratio over the past seven years has varied from 1.63 to 1.87 and averaged 1.72:1.00. All the same, as a practical matter crude steel production and iron ore consumption tend to parallel one another closely, and for the time being a good rule of thumb is that to produce an average ton of crude steel requires 1.20 tons of iron ore. Let's turn our attention now to the regions where the 859 million tons of iron ore necessary to support 1980 world-wide iron and steel production were produced. Not surprisingly, most of the ore was produced in the same region where it was smelted. In round numbers 65% of the world's iron ore production is currently consumed in the same general region as it is produced, while 35% enters the seaborne trade and is transported in ocean vessels to a more remote consuming area. Approximately 85% of the world's seaborne iron ore trade is directed to the Western European and Japanese markets, both of which are almost entirely dependent on off-shore sources for their mammoth iron ore requirements. The following tabulation lists, in order, the twelve leading iron ore producing countries in 1980 as well as their percentages of total and free-world production; in addition their export potentials are presented. As a group these countries accounted in that year for 89% of world-wide production which stood at 871 million tons. Leading World Iron Ore Producing Countries [ ] One will first note that world iron ore production is dominated by the top four producers - namely, the U.S.S.R., Brazil, Australia and the U.S.A. - which together accounted for nearly 60% of total 1980 production. Of these four major producers the U.S.A. and the U.S.S.R. produce almost exclusively for consumption in their own regions, whereas Australia and Brazil produce primarily for the seaborne export trade. In fact Australia and Brazil accounted for about 50% of all seaborne iron ore trade in 1980! It is also interesting to note that Australia, Brazil, the U.S.A. and Canada accounted for nearly 60% of free world iron ore production in 1980. Once again the importance of Australia and Brazil shows itself, with their share alone of free world production reaching 35%. As has already been noted, a significant 35% of the world's iron ore production in the year 1980 was

Jan 1, 1982

COMPARED with the equipment used in most industrial processes, the open-hearth furnace has a relatively short life. The most important quality of an open-hearth refractory, therefore, is its rate of failure. This discussion of the physics and chemistry of the individual refractory materials will keep uppermost the question "Why, how, and where does it fail?" CAUSES OF FAILURE The principal causes of failure of open-hearth refractories are, in their order of importance : 1. Reaction with iron oxides. 2. Reaction with slag. 3. Flow and failure under load. 4. Melting. 5. Spalling. 6. Mechanical breakage. Reaction with Iron Oxides and Slag. Reaction with iron oxides and slag is by far the most important cause of failure. Liquid iron oxide comes near to being the "universal solvent" sought for by the alchemists. Among the materials commonly used in the open-hearth furnace, magnesia has the greatest resistance to this liquid and fireclay the least. The relations of iron and oxygen at high temperatures are illustrated in Fig 14-18. The liquid iron oxide that forms wherever iron is in contact with air or combustion gases cannot be given a definite formula. The percentage of oxygen at steelmaking temperatures may range from 21 to 28 (iron 79 to 72), depending upon the temperature and the oxygen pressure and also upon whether or not the liquid is in equilibrium with metallic iron. Oxide mixtures exist not only in the solid and liquid phases but also in the vapor phase, for metallic iron and its oxides have

Jan 1, 1964

COMPARED with the equipment used in most industrial processes, the open-hearth furnace has a relatively short life. The most important quality of an open-hearth refractory, therefore, is its rate of failure. This discussion of the physics and chemistry of the individual refractory materials will keep upper- most the question "Why, how, and where does it fail?" CAUSES OF FAILURE The principal causes of failure of open-hearth refractories are, in their order of importance: 1.Reaction with iron oxides. 2. Reaction with slag. 3. Flow and failure under load. 4. Melting. 5. Spalling. 6. Mechanical breakage. Reaction with Iron Oxides and Slag. Reaction with iron oxides and slag is by far the most important cause of failure. Liquid iron oxide comes near to being the "universal solvent" sought for by the alchemists. Among the materials commonly used in the open-hearth furnace, magnesia has the greatest resistance to this liquid and fireclay the least. The relations of iron and oxygen at high temperatures are illustrated in Fig 14-18. The liquid iron oxide that forms wherever iron is in contact with air or combustion gases cannot be given a definite formula. The percentage of oxygen at steelmaking temperatures may range from 21 to 28 (iron 79 to 72), depending upon the temperature and the oxygen pressure and also upon whether or not the liquid is in equilibrium with metallic iron. Oxide mixtures exist not only in the solid and liquid phases but also in the vapor phase, for metallic iron and its oxides have

Jan 1, 1951

By G. Sachs, L. J. Ebert, W. F. Brown

IT is a generally recognized fact that a steel quenched from the austenitic range and tempered to yield a structure composed of tempered martensite becomes increasingly more ductile with increasing tempering temperature. However, the conventional tensile test fails to yield any value that is sensitive to differences in behavior on tempering among the various low-alloy steels or among different heats of a particular steel. The notched impact bending test, on the other hand, has been recognized for a considerable length of time as capable of revealing differences in impact properties among various steels tempered to the same strength level (i.e., the same tensile strength in a conventional tensile test), However, this test is very complex and its significance has not been clarified up to the present time. Of its three characteristic features-the high speed, the notch, and the bending-the notch has been found by Davidenkov2 to be the most potent embrittling factor. Recent investigations on low-alloy steels3,4,7,8 have shown static notch-bar tensile tests to be more lucid and to evaluate the metal properties in much the same manner as impact tests, In an attempt to analyze the fundamental nature of this test,8 it was found possible to separate the effects of the two basic characteristics of the stress pattern introduced by the presence of a circumferential notch, the stress state and the high initial stress concentration at the notch bottom, The major conclusions drawn from these previous investigations were as follows: I. The magnitude of the triaxiality at fracture depends primarily on the initial notch depth. Its effect is a great reduction in the average ductility (contraction in area at fracture in the notched section) as compared with that observed in uniaxial tension, This triaxial stress state occurs at a point in the interior of the notch specimen, It determines the notch ductility if the notch is mild and/or the metal possesses a considerable ductility. On the contrary, brittle specimens probably fracture on the metal surface (at the notch bottom) at which point biaxial stress state is present, This biaxiality also considerably reduces the ductility of the metal. For small notch ductilities the notch strength and the notch ductility become very sensitive to embrittling factors, This is contrary to the behavior of the ductility values derived from a conventional tensile test, which are comparatively insensitive.

Jan 1, 1946

By D. S. Sanders, E. W. Witcomb

FLOTATION tests, from which the flowsheet for the concentrator was determined, were made in a pilot mill at Chuquicamata and later comparative testing of full size flotation cells was done at the Andes Copper Mining Co. concentrator in Potrerillos. The principal sulphide copper mineral is chalcocite with varying amounts of covellite, enargite, and chalcopyrite. The oxidized portion is principally antlerite, a green basic copper sulphate. The gangue minerals include quartz, sericite, pyrite, feldspars and kaolin. Chuquicamata pit ores have proved to be hard grinding. The results of the flotation and metallurgical work prove that good extraction and concentrate grade can be obtained under a rather wide range of conditions. Metallurgy In general the metallurgy of the ore requires a fairly close control of the grind to the primary rougher flotation and of the regrind of the primary rougher concentrate before cleaning. Regrinding is necessary to reduce the insoluble content of the final concentrate since a large part of the middling combinations are between the copper and silica minerals. The alkalinity of the pulps can vary between wide limits and control of the percent solids gives the desired grind. Alkalinity Control Arroyo Salado water is supplied to the concentrator head tanks. It contains about 5000 ppm of salts but test work shows no deleterious effect. Actually this water permits a decrease of as much as 1 lb of lime per ton of ore as compared to San Pedro water, which is used for leaching oxide ore. About one quarter of the water flow through the concentrator will be new water from the reservoir. The remainder will be reclaimed from the thickeners. For primary grinding and rougher flotation, new and reclaimed water are combined in the head tanks. To avoid erratic results, only new water is used in the regrind system. Milk of lime is added to the rod mill feed chute to obtain the maximum benefit of mixing with the ore. This protects the equipment from corrosion due to entrained acids and soluble copper salts. Lime consumption is 3 to 5 lb per ton of ore. Grinding and Flotation The six bin gates over each belt feeder are opened in controlled combination and sequence to keep a live bed of ore in the bin to prevent arching and to obtain mixing. The milk of lime added ahead of the rod mill is regulated to suit rougher flotation requirements. The primary promoter reagent, Aerofloat 238, is added to the 10-mesh discharge of the rod mill as it is laundered to the ball mill scoop box. The classifier overflow is regulated to produce a grind of about 12 to 15 pct +65 mesh and 60 pct -200 mesh. A secondary promoter Z-4 (aml zanthate) and the pine oil frother are added in the overflow launder where a pH of 10 to 11 is maintained. Comparatively heavy beds of froth on the

Jan 1, 1952

By B. Ramaswami

INTERNAL oxidation occurs readily in silver due to the rapid diffusion of oxygen in silver.' It has a marked effect on creep in polycrystalline silver2 and raises the critical resolved shear stress in single crystals of silver.3 However, the effect of oxygen on the work-hardening parameters of silver is not known. It is the aim of this paper to describe the effect of internal oxidation on the work-hardening characteristics of single crystals of silver and an Ag-0.1 at. pct A1 alloy. The materials used were: 99.99 pct Ag from Handy and Harman and 99.993+ pct A1 from Alcoa. Single crystals, 6 mm by 6 mm in cross section of silver and Ag-0.1 at. pct A1 of mo.5 orientation, i.e., the orientation with the Schmidt factor m = 0.5. were grown by the Chalmers technique.4 One set of specimens, referred to herein as oxidized specimens, was annealed at 940°C for 24 hr in a muffle furnace, in air, and furnace-cooled to room temperature. Another set of specimens, referred to as nonoxidized specimens, was annealed in oxygen-free helium at 940°C for 24 hr and furnace-cooled over a period of 7 hr to room temperature. The annealed single crystals were tested at room temperature in a floor-model Instron testing machine. The results are presented in Figs. 1 and 2. A

Jan 1, 1965

By N. J. Grant, D. S. Bloom

An investigation of the Cr-Mo-Ni ternary system and attendant binaries has been completed. Some changes in the binary diagrams are shown to be necessary. The 1250°C section of the ternary and the liquidus surface have been delineated. A system of invariant reactions existing above 1250°C has been suggested. BECAUSE chromium, molybdenum, and nickel are important not only as bases for alloying systems but also as major alloying additions for other refractory metals, a study of the phase diagrams is of great interest and importance. In addition there are interesting features of theoretical value, a number of which are of prime consideration in this work. The major aim was to determine the ternary phase diagram of these metals at and above 1250°C, with sufficient attention given to lower temperatures to permit an understanding of the conditions existing at 1250°C and above. To understand ternary systems it is essential that accurate information concerning the binary systems be available, which in turn presupposes thorough knowledge of the constituent elements. On the basis of this investigation not only were significant inaccuracies indicated in the binary systems but much consideration had to be given to one of the elements, that is, chromium. The observation has been made that chromium undergoes a crystal transformation at a temperature near its melting point. Much of the experimental data leading to the detection of this transformation and the effects of this hypothesis on the form of the Cr-Ni phase diagram have already been reported' . and will not be repeated here. The experimental methods employed in the investigation have also been covered.'-" he purity of the molybdenum utilized in this work showed by qualitative spectrographic analysis that chromium, copper, iron, silicon, and tungsten were present in quantities of 0.1 to 0.001 wt pct. During the course of the investigation more than 100 melts were made, weighing from 150 to 200 grams each. Each of these melts was sectioned for chemical analysis and for specimens for examination in the as-cast and various heat-treated conditions by X-ray and metallographic means. All X-ray diffraction patterns reproduced here were made using chromium Ka radiation although iron and copper targets were used on occasions during the investigation. Experimental Results Mo-Ni-System: The most recent comprehensive investigation of the Mo-Ni system was made by Ellinger' in 1942; the diagram as shown in the American Society for Metals Handbook is based on his work. The work done on the system in this investigation substantiated the general form of the diagram although some differences were observed. These are indicated by a comparison of Ellinger's diagram and Fig. 1, the latter showing the results of pertinent thermal analyses made in this research. It can be seen in Fig. 1 that the eutectic composition is

Jan 1, 1955

By F. McIntosh Galbraith

This paper describes the use of the magnetometer, under geological direction, in exploration of the Sudbury nickel district. The writer's experience at Falconbridge has led him to the belief that only through detailed work, and by careful correlation of both geological and geophysical results, can geophysical prospecting methods be applied successfully to mining exploration problems. It is hoped that the basic technique described in the paper will be found to have general application. Introduction Within the past 20 years, geophysical methods of prospecting have become solidly established in the field of petroleum exploration. They have not, however, been similarly adopted by the mining industry, although mining is a far older craft and should be the more advanced in its technique. While, therefore, it is almost a routine matter to have geophysical surveys performed in a new area being tested for oil, a new metal-mining district is usually teeming with prospectors and promoters long before the technical man appears on the scene. Even then, only the more primitive engineering methods are customary in the early stages of exploration. Three factors are chiefly responsible for this situation, The first is the difference between oil pools and ore deposits in their geological modes of occurrence. While most of the known metallic ore bodies have been found outcropping at the surface, petroleum deposits are characteristically buried. This does not mean that all ore deposits outcrop, but neither does it mean that we should rely on "wildcatting" to discover blind ore bodies. The second factor is the relative scale of metallic lodes and accumulations of petroleum. In areal extent, a metal-bearing vein deposit is typically a much smaller geological feature than an oil pool. Presenting a narrower target, it requires closer shooting to score a direct hit. And finally, there is the need, in mining work, for close correlation of the known local geology with geophysical observations. This becomes of increasing importance as the size of the objective diminishes. A geophysical disturbance on a large enough scale will be detected under almost any circumstances and by almost any technique; without benefit of geology, however, the significance of a local anomaly may easily be misread. Campaign at Sudbury In the Sudbury nickel district of Canada, new deposits of nickel and copper have been discovered recently by magnetic methods, under geological supervision. A campaign of exploration, designed to encompass the district eventually, was set in motion in the spring of 1935. After six years, a new and important Ore body has been discovered and its continuity established to 1000 ft. in depth; several areas have been eliminated; and a number of possibilities remain to be tested. This has been accomplished with the expenditure of less than $$I50,000-—including the cost of all diamond drilling. The responsibility for carrying out this campaign was entrusted by the company to its Geological Department, and the under

Jan 1, 1946

By F. McIntosh Galbraith

This paper describes the use of the magnetometer, under geological direction, in exploration of the Sudbury nickel district. The writer's experience at Falconbridge has led him to the belief that only through detailed work, and by careful correlation of both geological and geophysical results, can geophysical prospecting methods be applied successfully to mining exploration problems. It is hoped that the basic technique described in the paper will be found to have general application. Introduction Within the past 20 years, geophysical methods of prospecting have become solidly established in the field of petroleum exploration. They have not, however, been similarly adopted by the mining industry, although mining is a far older craft and should be the more advanced in its technique. While, therefore, it is almost a routine matter to have geophysical surveys performed in a new area being tested for oil, a new metal-mining district is usually teeming with prospectors and promoters long before the technical man appears on the scene. Even then, only the more primitive engineering methods are customary in the early stages of exploration. Three factors are chiefly responsible for this situation, The first is the difference between oil pools and ore deposits in their geological modes of occurrence. While most of the known metallic ore bodies have been found outcropping at the surface, petroleum deposits are characteristically buried. This does not mean that all ore deposits outcrop, but neither does it mean that we should rely on "wildcatting" to discover blind ore bodies. The second factor is the relative scale of metallic lodes and accumulations of petroleum. In areal extent, a metal-bearing vein deposit is typically a much smaller geological feature than an oil pool. Presenting a narrower target, it requires closer shooting to score a direct hit. And finally, there is the need, in mining work, for close correlation of the known local geology with geophysical observations. This becomes of increasing importance as the size of the objective diminishes. A geophysical disturbance on a large enough scale will be detected under almost any circumstances and by almost any technique; without benefit of geology, however, the significance of a local anomaly may easily be misread. Campaign at Sudbury In the Sudbury nickel district of Canada, new deposits of nickel and copper have been discovered recently by magnetic methods, under geological supervision. A campaign of exploration, designed to encompass the district eventually, was set in motion in the spring of 1935. After six years, a new and important Ore body has been discovered and its continuity established to 1000 ft. in depth; several areas have been eliminated; and a number of possibilities remain to be tested. This has been accomplished with the expenditure of less than $$I50,000-—including the cost of all diamond drilling. The responsibility for carrying out this campaign was entrusted by the company to its Geological Department, and the under

Jan 1, 1946

By B. L. Sackett

LEAD smelting has been an important industry in Utah for many years. The first lead smelting was done, over 60 years ago, at the Rollins mine in Beaver County, by burning heaps consisting of alternate layers of wood and high-grade carbonate ore. The lead thus obtained was. molded into bullets. With the development of. the mines, the problem of cheaper handling of the ore became important. The only outlet for this ore was Swansea or the Atlantic Coast but to ship to either cost $150 per ton or more for treatment and handling. From 1864 to 1871, experimenting was done with blast, Scotch hearth, and reverberatory furnaces, with the blast furnace surviving as, the standard plant. The first crude furnaces were circular or hexagonal in shape, and were made of adobe and stone, which quickly burned out. They were small, about 2 1/2 ft. in diameter, and smelted from 3 to 10 tons. in 24 hr. The metal had to be tapped from the bottom of the crucible, necessitating a shut down of the furnace during this process. This pro¬cedure caused salamanders to form around the tap hole when the furnace was started again, which frequently resulted in freezing. The campaign lasted until a tap of bullion was made. The first successful plant of the crude stone type was operated in 1870. From 1870 to 1872, there was a smelter building craze in the state. During that period, about 20 furnaces were built, chiefly near the mines, and their operation was limited and sporadic. The work was then placed in the hands of trained metallurgists, who standardized on the rectangular form of furnace. In 1871, Daggett, at the Winnamuck mine in Bingham, installed water-jackets around the smelting zone of the furnaces. These furnaces were circular; the diameter at the tuyere line was 3 ft. 6 in. and at the charge floor 5 ft. 3 in. The height from tuyere line to charge floor was 14 ft., height of tuyere line above top of crucible was 3 ft. 8 in. Fur-

Jan 8, 1925

By M. C. Manderson

The sharp drop in world phosphate demand that took place in 1975 due to temporarily high prices, now seems to be reversing itself. And prices for both phosphate rock and phosphate fertilizers, which declined dramatically from their 1975 highs, now appear to be bottoming out. This recent price weakness has delayed new mining ventures that had been planned for completion by around 1980. While there is ample capacity to supply near-term rock needs, the stage seems to be emerging for a better supply-demand and price environment in the late 1970's and early 1980's.

Jan 1, 1979

By J. D. Defilippi, E. M. Gilbert, K. G. Brickner

FCC chromium-manganese-nitrogen (Cr-Mn-N) steels differ from most other fcc materials in that these steels undergo a ductile-to-brittle transition. Transformation to martensite is considered to be responsible for this behavior in some metastable Cr-Mn-N steels. However, very stable Cr-Mn-N steels also exhibit a ductile-to-brittle transition. The results of this study indicate that deformation faulting is the probable cause of the brittle behavior of stable Cr-Mn-N steels. Deformation faulting accounts for the ductile behavior of these steels in a tension test at -320°F and brittle behavior in an impact test at -320°F. Deformation faulting also accounts for the toPological features observed on the fracture surfaces of impact specimens of these steels. FACE- centered- cubic chromium-manganese-nitrogen (Cr-Mn-N) steels differ from most other fcc materials in that these steels undergo a ductile-to-brittle transition. Many Cr-Mn-N steels transform to martensite during deformation,l-5 and several investigatorsl-3 have suggested that the brittle behavior of these steels is caused by martensite formation. However, very stable Cr-Mn-N steels also exhibit brittle behavior. Schaller and Zackeyl reported that a very stable Cr-Mn-N steel (less than 3 pct martensite formed at -320°F) exhibited a transition temperature higher than that for steels in which large volume fractions of martensite formed during testing. The explanation given by Schaller and Zackey for this observation was that in the very stable steel the martensite, because of its higher interstitial content, was more brittle than that formed in their other steels. This explanation was questioned by Tisinai and samans4 and Baldwin.6 Moreover, because the toughness of stainless martensite at cryogenic temperatures is generally very low, this explanation does not account for Thompson's7 observation that small additions of nickel (1 to 3 pct) greatly improve the toughness of high nitrogen (0.35 pct) Cr-Mn-N steels. The present paper summarizes the results of an investigation of the low-temperature brittleness in very stable Cr-Mn-N steels. The importance of the mode of deformation on the toughness of these steels is discussed. Table I. Compositions of the Steels Invertigated, Pet Steel C Mn P S Si Ni Cr N - A 0.09 14.70 0.018 0.011 0.47 0.22 18.40 0.54 B 0.12 14.90 0.001 0.008 0.48 0.14 17.80 0.38 C 0.12 14.95 0.004 0.005 0.62 3.95 18.43 0.38 MATERIALS AND EXPERIMENTAL WORK The compositions of the steels investigated are shown in Table I. Steels A and B had compositions within the limits of a proprietary Cr-Mn-N stainless steel,* whereas Steel C was similar in composition to the proprietary steel except for its 3.95 pct Ni content. All steels were hot-rolled to 1/2-in. thick plate. The plates were subsequently annealed for 1 hr at 2000°F and water-quenched. Standard longitudinal and transverse Charpy V-notch impact specimens were machined from the annealed plates. Duplicate longitudinal and transverse impact specimens were tested at 212", 80°, 32", 0°, -100°,-160°,-200°,-256", and -320°F. Longitudinal tension-test specimens were also machined from the plates and tested at a crosshead speed of 0.05 in. per min at the aforementioned temperatures. The fractured impact and tension-test specimens of all three steels were examined to determine whether martensite had formed during testing. Magnetic, X-ray, electron-diffraction, and electron-microscopy techniques were used to detect the presence of martensite in the highly deformed areas of these specimens. Metallographic examination of highly deformed areas of impact and tension-test specimens revealed the presence of dark-etching bands, such as those shown in Fig. 1. These bands were observed only in deformed samples and were thought to be associated with the low-temperature brittleness of the Cr-Mn-N steels. Accordingly, a sample 1 in. wide by 3 in. long was cut from the 1/2-in.-thick plate of Steel C. This sample was surface-ground to a in. and then cold-rolled 60 pct at -320°F. Thin foils were prepared from the cold-rolled sample and examined in a JEM electron microscope. Brightfield, dark-field, and selected-area diffraction techniques were used to determine the cause of the dark-etching bands. Fractographic experiments were also performed. Impact specimens Of Steels A, B, and C were broken at -320oF, and the fracture surfaces of these specimens were immediately shadowed with carbon. The carbon replicas were examined in a Siemens electron microscope, and attempts were made to correlate the topological features of the fracture surfaces with the deformation mechanisms that could be occurring during an impact test of these steels.

Jan 1, 1970

By T. Sterry Hunt

THE essential principle of this new process, now in operation in Chili and in North Carolina, for the extraction of copper from its ores, is the dissolving of the oxides of copper by a hot solution of protochloride of iron and common salt. In the action which takes place, the protochloride of iron is converted into peroxide, while the oxides of copper are changed into protochloride and dichloride, the latter of which, though insoluble in water, is readily soluble in a hot strong brine. From the solution thus obtained, metallic iron throws down the copper in a metallic state, regenerating the protochloride of iron; which is then ready for the treatment of a fresh portion of oxidized copper ore. In the case of slimy ores, the contact of the bath with the ore is effected by agitation in tubs ; but when the ores are granular, lixiviation in large vats is equally efficient and simpler. The hot solutions, charged with chlorides of copper, are digested in tanks with scrap-iron, or better, are made to flow through covered channels containing the scrap-iron, and in their passage lose the whole of their copper; the reaction at the same time evolving so much heat as to keep up the temperature of the liquid. In order to prevent a certain loss of chlorine, which otherwise takes place from the production of some basic ferric chloride in the reaction between the ferrous chloride and the oxides of copper (both protoxide and dinoxide being generally present in calcined ores), a portion of sulphurous fumes from the roasting is made to pass through the regenerated bath before adding it to fresh ore. This has hitherto been effected by injection, with the aid of a jet of steam.

Jan 1, 1873