Search Documents

By Gilbert Soler

PRODUCERS of alloy steels recognize the importance of chemical composition in rela-tion to the hot-working properties and the typical surface defects found in their prod-uct. Each analysis of steel has its own peculiar characteristics. Under conditions of standard mill practice each analysis is susceptible to certain types of defects. Mill practice must be varied to obtain the best combination of surface and internal quality in the product. Chemical composition influences the cast structure and crystallization character-istics of the ingot. It also determines the rate of heating and cooling, the plastic hot-working range, and the phase structure of the steel at various temperatures as well as the tendency toward scale formation and decarburization, This paper endeavors to emphasize the manner in which chemical composition affects the various properties of steel, and to indicate the relative impor-tance of these factors in relation to the hot-working properties and surface charac-teristics of killed steel. The influence of chemical composition may be outlined as follows: I. Effect on the cast structure of steel, including: A. State of deoxidation, and type of inclusions. B. Gas content of steel. C. Freezing point and melting point of steel.

Jan 1, 1940

By Sylvan Cromer

The need for a clear understanding of the physical nature of the flow of gas-liquid mixtures in vertical pipes is ever becoming more apparent. This type of flow is encountered when gas and oil are produced from a well; when water is removed from gas wells with siphon lines and when liquids are elevated by means of air or gas lift. Although a number of investigator1-7 have published data on the flow of gas-liquid mixtures, in only a few cases has the experimental setup been devised to permit visual study. In the fields of heat transmission, such as the boiling of liquids and the study of the critical phenomena of the hydrocarbons, researchers have been able to throw additional light on heretofore unexplainable happenings through actual observation in glass apparatus. This investigation was therefore undertaken in order to obtain qualitative as well as quantitative results for air-water flow. Experimental Apparatus and Procedure The flow column used in these tests was made of standard 2-in. pipe and was approximately 98 ft. in height. Pyrex observation sections 2 ft. long having the same internal diameter as the wrought-iron pipe were placed at 14-ft. intervals in the column. The bottom of the tube was cut off square and terminated in the mixing chamber. No perforated nipple or footpiece of any kind was used. To the top of the column was fastened a semicircular return bend having a 4-ft. radius. The flow column was supported by a standard cable-tool drilling derrick (Fig. 1) into which were built observation platforms at each Pyrex section.

Jan 1, 1940

By Sylvan Cromer

The need for a clear understanding of the physical nature of the flow of gas-liquid mixtures in vertical pipes is ever becoming more apparent. This type of flow is encountered when gas and oil are produced from a well; when water is removed from gas wells with siphon lines and when liquids are elevated by means of air or gas lift. Although a number of investigator1-7 have published data on the flow of gas-liquid mixtures, in only a few cases has the experimental setup been devised to permit visual study. In the fields of heat transmission, such as the boiling of liquids and the study of the critical phenomena of the hydrocarbons, researchers have been able to throw additional light on heretofore unexplainable happenings through actual observation in glass apparatus. This investigation was therefore undertaken in order to obtain qualitative as well as quantitative results for air-water flow. Experimental Apparatus and Procedure The flow column used in these tests was made of standard 2-in. pipe and was approximately 98 ft. in height. Pyrex observation sections 2 ft. long having the same internal diameter as the wrought-iron pipe were placed at 14-ft. intervals in the column. The bottom of the tube was cut off square and terminated in the mixing chamber. No perforated nipple or footpiece of any kind was used. To the top of the column was fastened a semicircular return bend having a 4-ft. radius. The flow column was supported by a standard cable-tool drilling derrick (Fig. 1) into which were built observation platforms at each Pyrex section.

Jan 1, 1940

By James T. Wood

Stratigraphy, structure and closure of the Paloma field are discussed, with some details regarding the present state of development. The Paloma anticline, a large dome modified by faults, is the largest single closed dome in the southern San Joaquin valley without surface outcrop or topographic expression. It owes its discovery to geophysics. Of nine wells drilled to the Stevens sand, seven are productive. The ultimate productive area may approximate 3000 acres when the limits of the field are determined. Introduction The Paloma field derives its name from the Paloma school, ½ mile north of what is now the center of the field. The field is 17 miles southwest of Bakers-field, in the south central part of the San Joaquin Valley (Fig. I). The present developed area and its expected extensions are in townships 31 and 32S., R.26E. It is the most southerly of several fields that produce from the Stevens sand zone. The first well to produce condensate was a joint test drilled by the Western Gulf Oil Co. and The Texas Co. near the center of sec. 3, T.32S., R.26E., well No. 54-3. This well was completed on Aug. 31, 1939, at a depth of 10,178 ft. The initial production was 2280 bbl. a day of condensate and 14,750,000 cu. ft. of gas (½-hr. gauge) through a ?-in. bean. Prior to the drilling of this well, the Ohio Oil Co. discovered and developed a small gas field, which embraces a part of three townships about their common corner but lies chiefly in secs. 31 and 32, T.31S., R.26E. The first well was completed on July I, 1934, at a plugged depth of 5239 ft. after having been drilled to 7957 ft, production was found in a 59-ft. zone IIO ft. below the Fourth Mya bed, within the Sari Joaquin clays. Until recently this field was known as the Buena Vista gas field. It is now carried by the Division of Oil and Gas as the Paloma gas field. Production within the Paloma gas field is derived from six wells, producing from several different zones in the interval from 4177 to 5548 feet. Geology Stratigraphy The sediments penetrated by wells in the Paloma held range in age from Recent to Upper Miocene. The entire section, which exceeds 10,000 ft. in thickness, conforms generally to the standard section of the south central San Joaquin Valley. The producing zone, sometimes called the Paloma sand, is the approximate equivalent of the Stevens sand zone of the Ten Section, Canal, Coles Levee and other fields. The stratigraphic section is shown in Table I. Paloma Producing Zone* (Stevens Sand Zone, Upper Miocene) .-The Paloma producing zone (Fig. 2), frequently referred to as the Paloma sand, is encountered at depths ranging from 9950 to 10,300 ft. In general, it is a massive, firm to hard, not too well sorted, fine to medium fine sand. It is interbedded with thin, hard, calcareous sand shells of similar texture and cherty

Jan 1, 1942

By James T. Wood

Stratigraphy, structure and closure of the Paloma field are discussed, with some details regarding the present state of development. The Paloma anticline, a large dome modified by faults, is the largest single closed dome in the southern San Joaquin valley without surface outcrop or topographic expression. It owes its discovery to geophysics. Of nine wells drilled to the Stevens sand, seven are productive. The ultimate productive area may approximate 3000 acres when the limits of the field are determined. Introduction The Paloma field derives its name from the Paloma school, ½ mile north of what is now the center of the field. The field is 17 miles southwest of Bakers-field, in the south central part of the San Joaquin Valley (Fig. I). The present developed area and its expected extensions are in townships 31 and 32S., R.26E. It is the most southerly of several fields that produce from the Stevens sand zone. The first well to produce condensate was a joint test drilled by the Western Gulf Oil Co. and The Texas Co. near the center of sec. 3, T.32S., R.26E., well No. 54-3. This well was completed on Aug. 31, 1939, at a depth of 10,178 ft. The initial production was 2280 bbl. a day of condensate and 14,750,000 cu. ft. of gas (½-hr. gauge) through a ?-in. bean. Prior to the drilling of this well, the Ohio Oil Co. discovered and developed a small gas field, which embraces a part of three townships about their common corner but lies chiefly in secs. 31 and 32, T.31S., R.26E. The first well was completed on July I, 1934, at a plugged depth of 5239 ft. after having been drilled to 7957 ft, production was found in a 59-ft. zone IIO ft. below the Fourth Mya bed, within the Sari Joaquin clays. Until recently this field was known as the Buena Vista gas field. It is now carried by the Division of Oil and Gas as the Paloma gas field. Production within the Paloma gas field is derived from six wells, producing from several different zones in the interval from 4177 to 5548 feet. Geology Stratigraphy The sediments penetrated by wells in the Paloma held range in age from Recent to Upper Miocene. The entire section, which exceeds 10,000 ft. in thickness, conforms generally to the standard section of the south central San Joaquin Valley. The producing zone, sometimes called the Paloma sand, is the approximate equivalent of the Stevens sand zone of the Ten Section, Canal, Coles Levee and other fields. The stratigraphic section is shown in Table I. Paloma Producing Zone* (Stevens Sand Zone, Upper Miocene) .-The Paloma producing zone (Fig. 2), frequently referred to as the Paloma sand, is encountered at depths ranging from 9950 to 10,300 ft. In general, it is a massive, firm to hard, not too well sorted, fine to medium fine sand. It is interbedded with thin, hard, calcareous sand shells of similar texture and cherty

Jan 1, 1942

By E. R. Kaiser

COAL research during 1942 was directed in an important degree toward the solution of problems of wartime importance. A wider selection of coals for carbonization to meet the increased demand for coke, and the improved utilization of lower-grade coals for boiler fuel were made possible by fundamental studies on cod and ash behavior that had been started several years ago. The coal industry's interest in the work of the various laboratories brightened significantly as results were demonstrated on smokeless combustion in stoves, on stokers without coke trees, and on pulverized firing of forge furnaces. Despite the limitations of priorities and scarcity of materials, the mineral industries building of the West Virginia University was completed and equipped with facilities for research on coal min

Jan 1, 1943

By A. P. Svenningsen

DURING the work at the test mill in Morenci, it was determined that a suitable feed for the ball mills could be made by a single pass through a short-head cone crusher. These crushers did not require a closed circuit delivering only a screen product to the mills, such as is the practice in some concentrators. By no means does this mean that the practice in these other concentrators is wrong, but just that the Morenci ore can be most economically crushed and ground in this manner. Therefore, the design of the secondary crushing plant was simply a problem of taking 25,000 tons of ore per 16 hour day from the primary crusher, this ore ranging in size from fine particles to 10 or 12 in., and reducing it to minus 3/4 in. Inasmuch as outages must be contended with in any crushing plant, it was assumed that the crusher would operate at full capacity for approximately only twleve hours per day, which is three-quarter capacity for the 16-hour shift. With this in mind, it was necessary to design a crushing plant which would average approximately 1600 tones per hour for the 16-hour day, or 2000 tons per hour for slightly over 12 hours per day.

Jan 1, 1942

By K. A. Svanstrom, W. R. Opie

Problems associated with deposition of titanium infused chloride baths using TiCl4 as a feed material are reviewed. A potentially workable cell design using Alumdum diaphragms is discussed. Problems inherent to diaphragm-type cells are emphasized and experiments described which led to the development of a cell without a diaphragm. INVESTIGATORS assigned the problem of developing a commercial electrolytic process for making titanium metal have found that they are faced with the difficulty of overtaking rapidly improving magnesium and -sodium reduction processes. The ultimate goal must be a simple process that can be conducted with low-cost raw materials in equipment that is inexpensive to build and operate. This paper deals with some work of a preliminary nature conducted by personnel of the Research Laboratories, National Lead Co., Titanium Division. Many others have reported on the general subject of depositing titanium from fused salt electrolytes. A partial bibliography is attached. PRIMARY CONCEPTS Anyone attempting to deposit titanium metal from fused chloride electrolytes using TiC14 as a source material is faced with at least the following problems: 1) Getting the titanium into solution in the bath. 2) Controlling oxidation and reduction reactions associated with multiple valency of titanium, which result in low electrical efficiency. a) Prevention of dichloride oxidizing to trichloride and trichloride to tetrachloride at the anode. b) Prevention of trichloride from being reduced only to dichloride at the cathode. 3) Prevention of metal formation away from the cathode thru disproportionation of titanium dichloride to satisfy the equilibrium. 3 TiCl2 == 2 TiCl3 Ti [I] 4) Protection of reduced chlorides in the bath from reaction with oxygen from the bath container or air. 5) Removing from the bath the deposited metal formed without allowing it to become contaminated with oxygen or nitrogen. 6) Selecting cell materials of construction which will not contaminate the metal product or cause cell inefficiencies. EARLY EXPERIMENTS The initial attempts made to electrodeposit titanium from fused chloride baths using TiCl4 as a source material indicated that TiCl4 was essentially insoluble in molten chlorides of alkali and alkaline earth metals. If, however, the TiCl4 was introduced close to a nickel cathode some metal could be formed and appreciable quantities of reduced chlorides would be present. These reduced chlorides reacted with any oxygen present in the atmosphere above the bath and would also diffuse quickly to the anode (graphite) where they would react with chlorine and be evolved as TiCl4. The net electrolytic efficiency of such a cell is essentially nil. The TiCl4 evolves from the anode at almost the same rate that it is introduced in the vicinity of the cathode although a small amount of titanium metal can be formed on the walls of the cathodic pipe. It becomes apparent from the operation of such a cell that: metal can be deposited on the cathode, although of small particle size and a nonadherent nature, and when reduced chlorides are present in the electrolyte, TiCl4 can be absorbed, probably by the following reactions: TiCl4 + TiC12 - 2 TiCl3 [21 2 TiCl3 + 2 faradays - 2 TiC12 + C12 [31 DIAPHRAGM CELLS These facts encouraged the development of cells containing diaphragms to prevent migration of reduced chlorides from the cathode area to the anode. Small-scale cells for process development are described by Alpert, Schultz, and Sullivan.20 A larger brick-lined cell incorporating internal heating by passing ac through the bath is shown in

Jan 1, 1960

By Fred C. Bond

MANY grindability tests have been made in the Allis-Chalmers laboratory since the tabulated results were last published.1 The lists of standard ball-mill and standard rod-mill grindability tests are brought up to date in this paper, and considerable new material is added. This includes a tabulation of open-circuit grinding tests, with impact and compression-crushing tests. The standard ball-mill grindability tests (Table I) were made in a standard laboratory ball mill, 12 by 12 in. inside, running at 70 rpm, with a charge of 285 iron balls ranging from 1 1/2 to 3/4 in. in diameter and weighing 20,125 grams. Seven hundred cubic centimeters of minus 6-mesh stage-crushed dry feed was used, and the circulating load was maintained constant at 250 pct by adjusting the number of mill revolutions for each grinding period. Tests were made at all mesh sizes from 28 to 200, and the grindability is the number of net grams of screen undersize produced per revolution. The table includes 479 tests. It has been calculated that the ball mill does 52.3 joules of useful work on the ore per revolution2 with 93 joules input to the mill. The standard rod-mill grindability tests (Table 2) were made in a laboratory tilting rod mill, 12 in. in diameter by 24 in. long inside, with a wave-type lining, running at 46 rpm. The grinding charge consisted of six 1 1/4-in. diameter and two 1 3/4-in. diameter steel rods, all 21 in. long and weighing 33,380 grams. The mill was rotated level for eight revolutions, then tilted up 5° for one revolution, down 5° for one revolution, and returned to level for eight revolutions. It was discharged by tilting downward at 45° for 30 revolutions. Feed consisted of 1250 cc of minus 1/2-in. stone and the circulating load was maintained constant at 100 pct by adjusting the number of mill revolutions for each grinding period. Tests were made at all mesh sizes from 3 to 65, and the rod-mill grindability is the number of net grams of screen undersize produced per revolution. The table includes 105 tests. The impact and compression-crushing tests (Table 3) are given in a table that is an extension of a previous publication3 in which the method of testing was described in detail. Two equal hammers weighing about 30 lb each were arranged to strike simultaneous blows on opposite sides of the test specimen. Broken pieces of rock passing a 3-in. square and retained on a 2-in. square were set up with the smallest dimension between the hammers, and this distance was measured. The height of the hammers was increased slightly before each blow until the specimen broke, and the foot-pounds per inch of thickness was calculated. Ten pieces

Jan 1, 1947

By C. W. Phillips, D. N. Frey

A commercial Ti-Fe-Cr alloy, Ti-150, exhibits a martensitic transformation on cooling and two nucleation and growth reactions, one above and one below the Mg-Mf region, on isothermal holding below the single-phase ß temperature range. The reactions were followed by metallographic, X-ray diffraction, and microhardness methods. THE rapidly expanding engineering application of titanium and its alloys makes increasingly urgent an adequate knowledge of the effect of heat treatment on this material. The work herein reported is an attempt to determine certain aspects of the behavior of a commercially available alloy, Ti-150, during heat treatment. The alloy, with a nominal composition of 2.7 pct Cr, 1.3 pct Fe, 0.25 pct 0, 0.02 pct N, and 0.02 pct C, was received in the as-rolled condition as a 3/4 in. round. Slugs 0.11 to 0.12 in. thick were cut under a coolant using a silicon carbide wheel. Preliminary work established that the alloy consists of two phases, a (hexagonal close-packed) and /3 (body-centered cubic), at temperatures below 1750" to 1775"F, and of only /3 phase at higher temperatures. The slugs were heated for 1 hr in air at 1800°F to form a single-phase /3 matrix, then transferred to molten tin (1250° to 1650°F) or lead (1150°F and below) for isothermal holding. Holding temperatures ranged from 700° to 1650°F, times from 0.001 to 23 hr. The treated slugs were then sectioned, one part for metallographic examination and diamond pyramid hardness, the other, after deep etching to remove the high oxygen surface,' for comparative lattice parameter determination and X-ray phase identification. Hardness measurements were taken on the lightly etched surfaces of the metallographic specimens; a 1000 g load on a 136° diamond pyramid was used. Five impressions on each sample were made and the average of the hardness calculated. The use of microhardness measurements to follow the course of an isothermal transformation reaction is undesirable because of the possibility of wide differences in microconstituent hardness.' They were used in this case, however, because of the small amount of material available. At the higher transformation temperatures, where the above-mentioned objection was apparent, the readings were proportioned to correspond to the estimated ratio of transformed and untransformed constituents present. At lower temperatures, resulting in much finer microconstituents, the microhardness measurements were more uniform. The standard deviation of the mean of five impressions calculated from these latter values was 4.2 DPH. Employing 2a limits (probability 0.95) the experimental error of the hardness measurements averages was 8.4 DPH. The etchant used was composed of one part glyc-erol and one part 48 pct hydrofluoric acid." Of a number of etches tried, this one appeared most satisfactory. All micrographs were taken at 500X magnification and with oblique lighting to permit easier identification of the acicular structure resulting from rapid cooling. No advantage was gained by using polarized light for metallographic examination. Phase identification and lattice parameter measurements were made with a North American Philips high angle spectrometer in conjunction with a recording potentiometer. Considerable difficulty was encountered with some of the lattice parameter measurements because of the extreme broadness of the few diffraction lines obtained from samples consisting mainly of strained, untempered, quenched structures.

Jan 1, 1953

By AIME AIME

FEW mining engineers-noted as the profession is for migratory predilections.--can point to as varied a record as Scott Turner, director of the U. S. Bureau of Mines and newly elected vice-president of the Institute. His record as printed shows that from the time of his graduation from the Michigan College of Mines in 1904 until he went to the Bureau in 1925, he worked for 21 different companies. Geographically the record is no less imposing, although one reason for this is the fact that he was field engineer for several exploration companies. Virtually every important mining state in the Union is represented in addition to Canada, Alaska, Panama, and several countries each in South America and Europe. In addition to all of the common metals he has mined tin and coal. He opened and operated for five years a group of coal mines in 73" 13' S. Lat., on the Island of Spitzbergen. This was 825 miles north of the Arctic Circle on No Man's Land, where Mr. Turner claimed and maintained pos- session under the American flag of an area of 600 square miles. Incidentally, he was a survivor of the ill-fated Lusitania, sunk by a submarine in May, 1915.

Jan 1, 1930

By GEORGE D. RAMSAY

ABOUT three miles west of Fontana San Bernardino County, California, and fifty miles east of Los Angeles, the Kaiser Co., Inc., has built an integrated steel plant. By integrated, I mean that from its wholly owned iron ore and coal supply, the Kaiser Co. is producing in its own mills iron and steel products. Pig iron to meet the West Coast needs has been produced at Fontana since Jan. 1, 1943; steel ingots were first poured there May 14, 1943; and steel plate for ships was first rolled Aug. 15, just sixteen months after ground was broken. Briefly, the plant consists of: (I) Two batteries of by-product coke ovens, totalling ninety ovens, carbonizing about 1740 tons of coal per day at capacity; with by-product facilities for the production of tar, ammonia, and ammonium suIphate, light oil distillates, and tar distillates. (2) One blast furnace producing at

Jan 1, 1944

By Glenn R. Zellars, J. P. Morris

The carrier gas method was used to measure the vapor pressure of copper over liquid copper and Fe-Cu alloys. From these results, the activity of copper in the alloys was determined at 146°, 1550°, and 1600°C. Calculations of the activity of iron were made from the results for copper. The activities of copper and iron show strong positive deviations from Raoult's law. KNOWLEDGE of vapor pressures of liquid metals has both practical and theoretical value. Fuming of metal baths is directly related to vapor pressure, and the data should bc particularly important to the technology of vacuum metallurgy. Theoretical applications include determinations of heats of vaporization, heats of solution, and activity coefficients in alloys. Methods for measuring vapor pressures of metals have been reviewed by Speiser and Spretnak.' High-vacuum procedures, such as the Langmuir and Knudsen methods, have been used most widely in recent years. However, these methods are not applicable to vapor pressures greater than lo-' mm Hg and often cannot be used in the temperature range of greatest interest. The purpose of this investigation was to develop a procedure for measuring vapor pressures of pure metals and alloys that would be applicable to pressures greater than lo-' mm Hg. The transportation or carrier gas method has been used. Copper was chosen for the initial work because its vapor pressure has been established fairly well and the reliability of the technique could be ascertained. Applicability to alloys was studied by determining the vapor pressure of copper over liquid Fe-Cu alloys. Experimental Procedure The tests were carried out in a graphite-spiral resistance furnace. The charge consisted of 50 g of metal contajned in a covered sintered-alumina crucible 1/2 in. deep and 13/8 in. ID. Two sintered-alumina tubes led from outside the furnace to within the crucible, passing through close-fitting holes in the crucible cover and radiation shield. The arrangement of the crucible and the two alumina tubes is shown in Fig. 1. The small-bore tube (1/16 in. ID by 5/16 in. OD) served as the inlet for the carrier gas. The tip of this tube touched the metal surface and the flow of gas imparted a rippling motion to the metal. In this manner the gas was brought into close contact with the metal and became saturated with metal vapor. In most of the tests the flow rate of the carrier gas was 560 ml per min, measured at room temperature. Approximately half of this saturated gas was allowed to escape from the crucible through the second alumina tube (3/16 in. ID by 5/16 in. OD) and was discharged to the atmosphere through a

Jan 1, 1957

By Grover R. Castle

INTRODUCTION Banks are being asked to assume more and more of the project risk in connection with project financings and, as a result, they are seeking to become more sophisticated in the way that they approach these kinds of financings. For example, a large number of banks that are active with the mining companies have established mining groups which typically will include mining engineers, economists, and bankers, in order to specialize their service to the mining industry. These banks have geared up these special service staffs so that they will be better equipped in their lending activities to analyze, measure and evaluate the project risk. The hope is that a team of these specialists will be able to predict the potential success or failure of these new "green fields" mining ventures that the banks are asked to finance. This paper shall focus on this subject and try to determine just how successful these specialists can hope to become as they analyze these various projects that are brought to them for financing. The approach that shall be taken in this paper shall be to examine how successful the mining companies themselves have been in the past with this same problem. These mining companies should be the most sophisticated in their approach to the analysis of the potential for success of a new mine because they have had the most experience in evaluating these projects. After all, who knows more about developing a mine than the companies that have developed similar mines in the past? For the purposes of this paper, the writer has selected a sample of 18 mines that have been developed over the years and measured the actual performance of each of these sample ventures against the original projections. All of these cases have involved the development of large projects where the sponsors or partners in the venture are substantial and sophisticated companies and where the feasibility studies have been prepared by engineering firms that are considered very professional in the industry or alternatively where the feasibility has been done by a comparable in-house staff. The sample cases have been chosen from a period which starts in 1965 and continues through 1981 with the cases distributed over that period as indicated below: [ ] Fourteen of the projects are open pit mines, three are underground mines and one mine starts on the surface and gradually goes underground. Seven of the mines are in the the far east with the remaining three in either South or Central America. The following four specific questions were examined for each project:

Jan 1, 1985

By William J. Coulter

WITHIN the past thirty years the United States has been involved in two tragic, vicious, and costly world wars. To make the world safe for democracy was the reason given for our participation, but the confusion and misunderstanding that prevails all over the world today suggests that war is not the proper approach to the attainment of that utopia. These conflicts were conceived and prosecuted by nations far advanced in civilization and culture. Their best manhood was sacrificed, a staggering tax burden was saddled on their peoples, huge financial losses were incurred, destruction of property was appalling, and cultural and peaceful scientific advancement received a setback that may require centuries to retrieve. Therefore, some basis is established for the conclusion that progress in the past fifty years has been most outstanding in the development of instruments used for death and destruction, and that progress in this direction between the two World Wars would indicate that the next war will go far toward total destruction of world civilization.

Jan 1, 1946

By Frederic Dewey

(New York Meeting, February, 1913) This old and well-known method of determining, silver is, in bullion work, so far superior to the furnace-assay that it is looked upon with reverential awe by many, if not by most, users, and its-ease of execution, with proper equipment, commends it highly where much commercial bullion work on silver is required. The method is so thoroughly well known that a, description of it here may seem to be unnecessary, but many thousands of determinations are annually made by it in the U. S. Mint Service and its practice is there reduced to an art. This is necessary both for the sake of economy of time, acid because high-grade work with it requires constant practice. It is useless for a person who uses it only occasionally to expect to attain high accuracy with it, without spending more time upon a determination than is warranted in a busy commercial laboratory. It is always employed in the Mint service whenever possible, but its chief field is in the determination of silver in standard silver (ingots and coin), which is 900 fine in silver and 100 fine in copper, and I shall first briefly outline its use on this metal and then take up various points in detail, especially as related to the accuracy of the results obtained.

Jan 4, 1913

By J. D. Lubahn

The Bauschinger effect, or rounding of the corner of the stress-strain curve upon reloading, represents a temporary apparent softness that is more pronounced at large strains than small and for complete unloading than for partial unloading. Interrupted creep tests on copper exhibit a similar temporary softness (high creep rate) upon reloading. The fact that the strainwise dying-out time of these effects is the same in both tensile and creep tests shows that they are related. Thus, the term Bauschinger effect appears to embrace behavior following partial or complete unloading and reloading in addition to behavior following reversed loading. It is suggested that the term may properly apply also to certain creep behaviors following a small load decrement. INTERRUPTED tensile tests at low temperatures show1 a rounding of the corner of the stress-strain curve for reloading, which indicates a temporarily low deformation resistance. In the absence of recovery, the curve soon rises to the value that would have prevailed if the test had not been interrupted. The rounding of the reloading tensile curve has sometimes been referred to1 as the Bauschinger effect, although the term is more commonly applied to low deformation resistance in compression following tensile prestrain. The unusually broad usage of the term Bauschinger eflect in ref. 1 seems justified by the obvious interconnection of the various behaviors to which it has been applied.' In fact, the following discussion will indicate that still broader usage might be desirable. The Bauschinger effect is common at room temperature but apparently disappears at higher temperatures.2 Interrupted creep tests and tensile tests were made on certified OFHC copper (nongaseous impurities exclusive of silver were 0.004 pct), cold drawn 84 pct to ½ in. diam, and annealed at 600" (about 0.025 mm grains) or 850°C (about 0.2 mm grains). The tests were made in standard creep or tensile machines, using an O.S. Peters microformer-type extensometer or, for the small plastic strains, a special arrangement employing General Electric magnetic gage heads.' Interrupted creep tests at room temperature show3,4 an initial softness after reloading, manifested by an initial creep rate that is higher than that which would have prevailed if the test had not been interrupted. Fig. 1 shows some typical examples. This effect is apparently temporary (as is that in tensile tests): in four of the five tests shown, the log rate vs strain curve becomes parallel to an

Jan 1, 1956

By James R. Jones

The concern for air pollution goes back centuries as will be seen from this quotation : "Strife and coal, it seems, have a hand-in-hand historical relationship. It was thought by some . . . in the Middle Ages that burning coal filled the air with dangerous poisons. So great was the concern that in 1306 King Edward I of England passed the first and unquestionably the harshest air pollution legislation edict that history will record. His proclamation declared the use of coal an act punishable by death." As related to coal mining, the air pollution problem is primarily that of its customer when using the fuel. Thus the major impact relates to markets for coal rather than the actual mining operation itself. In the vicinity of the coal mine the problem is principally related to fugitive dust from roads, transfer facilities, loading facilities, crushers, etc., and particulate matter (dust or fly ash) from thermal dryers and air cleaning tables. FUGITIVE DUST Most state air pollution regulatory agencies now have rules and regulations requiring control of fugitive dust. Fugitive dust has been defined by the courts as particulate matter other than that emanating from a specific point such as a stack or chimney. A typical air pollution control agency regulation reads as follows : “Fugitive Dust " "No person shall cause, suffer, allow, or permit any material to be handled, transported, or stored; or a building, its appurtenances, or a road to be used, constructed, altered, repaired or demolished without taking reasonable precautions to prevent particulate matter from be- coming airborne. Such reasonable precautions shall include, where applicable, but not be limited to the following:

Jan 1, 1981

In uranium metallurgy, the main purpose is to obtain a product containing 80-85% U308 (yellowcake) from ores whose average grade is a mere 0.21% U30& Essentially, the task of extraction and concentration involves dissolving the ore's U308 values, followed by purification and concentration of the uranium-rich solution (using such operations as filtration, clarification, and ion-exchange), and then selectively precipitating and isolating U308. Leaching is First Step In yellowcake production mills, the first chemical change occurs by leaching the ore with either sulfuric acid-as done by Anaconda and Kerr-McGee-or with an alkaline solution of, say, sodium carbonate, as done by United Nuclear-Homestake Partners. The choice of either acid or alkaline leaching is not an arbitrary one: it depends on the chemical and physical characteristics of a particular ore. That is, on the presence of clays, organic compounds (usually of carbonaceous origin), and soluble impurities, as well as on the ore's wetness and grindability.

Jan 8, 1974

By R. F. Ashton, D. S. Thompson

In reporting results of precipitation hardening experiments, it is customary to include such conditions as solution heat-treatment temperature, specimen size, and quench medium as well as the aging time and temperature. One portion of thermal history that is often overlooked is the effect of the heating rate employed to achieve the aging temperature. It is the intent of this note to demonstrate the importance of the rate of heating to aging temperatures. This work was carried out on the aluminum alloy 7075 aged at 162oC, a temperature commonly used to obtain stress corrosion resistant tempers. A 2 in. thick plate of 7075 was quenched into 24°C water after solution heat-treatment for 2 hr at 470°C. Approximately 13 in. around the periphery of the plate was discarded to minimize quench rate variations, and the remainder was divided into 0.5 by 1.8 by 2.0 in. blocks which were held at room temperature, 24oC, for 4 days. This aging, or incubation period, at room temperature allowed a copious supply of GP-zones to form. Blocks were then heated at various rates to 162oC using the practices shown in Table I. Both single- and two-step aging practices were employed for each heating rate. The single step consisted of heating directly to temperature at the indicated rate while the two-stage practice included an interruption of heating for 7 hr at 107°C. In the case of the two-stage 100°C per min heating rate experiment, the specimens were returned to room temperature after 7 hr at 107°C where they were held for 16 hr be-fore finally heating at this rate to 162°C. This devia-tion in practice is not considered to be significant. Blocks were removed after various times at 162oC, and aging curves were determined from duplicate R. F. ASHTON and D. S. THOMPSON,Member AIME, are Senior Scientists, Metallurgical Research Division, Reynolds Metals Company, Richmond. Va. Manuscript submitted December 2. 1968. IMD Table I. Aging Practices Two-step Single-Step Heating Rate* Aging Aging Heating Method oC per Min A B Programmed Air Oven 0.23 * 0.01 C D Programmed Air Oven 0.93 ? 0.03 E F Air Oven at Temp -10 G H Oil Bath at Temp ˜100 *Heating rate was measured with a thermocouple at the center of a specimen. An average value between the starting temperature and 3°C below the aging temperature is reported for practices E-H. PRACTICES 70 — A B C E and G 50 - 2 4 6 810 20 40 60 HRS.AT 162°C Fig. 1—The influence of processing variables on 7075 aging curves. Fig. 2—7075 aged according to practice H (single-step aged, fast heating rate) for 3 hr. Magnification 100,000 times.

Jan 1, 1970