Search Documents

By Thomas T. Read

EVERYONE engaged in the teaching of mining engineering will, I suppose, agree that the most difficult subject to teach is "Mining Methods." One primary difficulty is that the students taking the course have either had no previous experience in mining, or else they have had; either seeming to be somewhat of a drawback. The students who are unfamiliar with mines find it difficult to visualize underground conditions, as described and illustrated with sketches and maps, while those who have had underground experience seem to 'find it difficult to visualize anything much different from that which they have already seen. This reminds one of the remark about the Presbyterian doctrine of predestination, to the effect that "you are damned ,if you do; and damned if you don't."

Jan 1, 1930

By J. R. Lewis

During the past few years there has been considerable interest in the sizing and the preparation of the iron ore fed into blast furnaces. Furnacemen know that proper sizing of ore tends to increase the efficiency of the furnace. It has been shown by Joseph1 and his associates that there is a direct relationship between the porosity of an ore particle and the time required for its reduction in the blast furnace. This relationship may be stated as follows: All other factors remainig constant, the time for reduction of a given sample of ore is inversely propor-tiofid to its porosity. As a consequence, large pieces of very porous ore, say 3 or 4 in. in cross section, will be completely reduced by the time they reach the hot zone just above the tuyeres, while large pieces of dense, nonporous ore may reach the hot zone with their centers unreduced. This means that for the latter complete reduction will be accomplished by the so-called "direct method;" i,e., where carbon reacts directly with the ore. Some recent work by philbrook2 seems to contradict this rule. He found that of two unlike ores he studied, the one with the lower porosity reduced more readily. He explained his results as "possibly due to an apparently greater tendency of the rA, ore (lower porosity) to crack during preliminary dehydration and during reduction." This brings his results in line with the rule stated above. It is not the author's intention to enter into a discussion of the merits of "direct" versus "indirect" reduction. It is enough to Say that, in general, indirect reduction is desirable. For the greatest efficiency, Gruner's theorem3 requires that all reduction in the blast furnace be indirect. Joseph seems to believe this also, because in his recent article on Some Comparisons between Iron Ore, Sinter and Nodules as Blast Furnace Feed4 he concludes that: "In genera', the carbon in blastfurnace coke is used most efficiently when the largest amount of the carbon charged reaches the tuyeres." However, P. V. hlartin,3 in an excellent paper, has shown that some direct reduction may actually increase the efficiency of the furnace; that is, increase its rate of production while maintaining maximum fuel economy. For nonporous ores there is more opportunity to have an excess of direct reduction unless the factors that make for indirect reduction are favored; for instance; the Proper sizing of the Ore particles' Another factor that has an important bearing on the reduction rate, as it is affected by particle size, is the flow of heat into the particle. The ore particle

Jan 1, 1948

By J. R. Lewis

During the past few years there has been considerable interest in the sizing and the preparation of the iron ore fed into blast furnaces. Furnacemen know that proper sizing of ore tends to increase the efficiency of the furnace. It has been shown by Joseph1 and his associates that there is a direct relationship between the porosity of an ore particle and the time required for its reduction in the blast furnace. This relationship may be stated as follows: All other factors remainig constant, the time for reduction of a given sample of ore is inversely propor-tiofid to its porosity. As a consequence, large pieces of very porous ore, say 3 or 4 in. in cross section, will be completely reduced by the time they reach the hot zone just above the tuyeres, while large pieces of dense, nonporous ore may reach the hot zone with their centers unreduced. This means that for the latter complete reduction will be accomplished by the so-called "direct method;" i,e., where carbon reacts directly with the ore. Some recent work by philbrook2 seems to contradict this rule. He found that of two unlike ores he studied, the one with the lower porosity reduced more readily. He explained his results as "possibly due to an apparently greater tendency of the rA, ore (lower porosity) to crack during preliminary dehydration and during reduction." This brings his results in line with the rule stated above. It is not the author's intention to enter into a discussion of the merits of "direct" versus "indirect" reduction. It is enough to Say that, in general, indirect reduction is desirable. For the greatest efficiency, Gruner's theorem3 requires that all reduction in the blast furnace be indirect. Joseph seems to believe this also, because in his recent article on Some Comparisons between Iron Ore, Sinter and Nodules as Blast Furnace Feed4 he concludes that: "In genera', the carbon in blastfurnace coke is used most efficiently when the largest amount of the carbon charged reaches the tuyeres." However, P. V. hlartin,3 in an excellent paper, has shown that some direct reduction may actually increase the efficiency of the furnace; that is, increase its rate of production while maintaining maximum fuel economy. For nonporous ores there is more opportunity to have an excess of direct reduction unless the factors that make for indirect reduction are favored; for instance; the Proper sizing of the Ore particles' Another factor that has an important bearing on the reduction rate, as it is affected by particle size, is the flow of heat into the particle. The ore particle

Jan 1, 1948

By J. A. Knox, R. M. Lasater, J. M. Tinsley

Chemical squeeze treatments have been used to provide temporary relief from certain production problems. The chemical fracture-squeeze technique, combining the effects of a fracturing treatment and a squeeze operation, has been more successful than conventional squeeze operations. Knowledge derived from well stimulation and reservoir engineering research provides a means for predicting the theoretical effective life of such a treatment. Analysis of theoretical equations and concepts developed allows selection of improved treatment techniques based on specific formation conditioins. Theory used in this analysis was developed as an extension of previous electrical model studies made to establish the expected flow and pressure profiles adjacent to a fracture system. The chemical fracture squeeze technique can be utilized in the economic application of corrosion inhibitors, emulsion breakers and paraffin and scale inhibitors. Application of this technique is shown to be effective. The slow return rate of injected chemicals, controlled by the resultant flow profiles and treatment variables, permits extended periods of chemical effectiveness. Results of field treatments are given, showing that the concepts outlined above for chemical fracture-squeeze treatments are valid and that applying this technique can help alleviate many current production problems. INTRODUCTION Much progress has been made in the last 10 to 15 years in developing chemicals for use in stimulating wells, maintaining production and protecting well equipment from damage due to corrosion. Not too many years ago, some wells seemed to dry up or wear out. In many cases the wells were produced as long as possible without any attempt at maintaining productivity. Even with the advent of new and better stimulation techniques, a rapid decline in production was observed. Methods of removing and, in some instances, preventing damage have been developed. Among thosc factors responsible for uneconomical production are scale, paraffin, corrosion, bacteria, water blocks and emulsions. Soluble scale-prevention chemicals have been developed1,2 that can be placed in a formation along with frac- turing sand. As the water produces back across this bed, the solid material dissolves slowly and can provide long-term protection from scale. However, bottom-hole temperature and salinity of produced water vary widely and both these factors influence the rate of solubility. Scale inhibitor composition is also a controlling factor. Some of the solid material may be crushed, increasing the surface area exposed to water and increasing the rate at which it dissolves. Some of the material may never be contacted by water and can be lost. However, this type of treatment has been very successful in many instances and has helped maintain economical production for extended periods of time. Liquid scale inhibitors, which are more widely applicable and more stable, have been developed in recent years; however, because they are liquids, their use has been restricted to treatment down the annulus, using metering pumps to provide proper concentrations in the produced fluid. This has prevented use in wells containing packers, in dually completed wells and in gas-lift and flowing wells. Wells that operate with an open annulus may also experience severe corrosion problems due to introduction of oxygen. Paraffin inhibitors3 have been developed that can be fractured into a well as particulate solids to be slowly dissolved in the produced fluid. These materials are not usually effective in wells with a bottom-hole temperature in excess of 120F since solubility rate may be too fast if that temperature is exceeded or if aromatic content of the oils is unusually high. Corrosion inhibitors have been developed that can be fractured' into a well for long-term feedback, but development of a material with proper solubility or feed rate has been difficult. Corrosion inhibitors are available in many different forms. Liquids have been lubricated down the annulus or sticks or pellets dropped down tubing. Inhibitor squeeze treatments5 devcloped a few years ago led to development of inhibitors with particularly strong film-forming properties.6,7 This technique basically involves displacing a highly concentrated solution of the inhibitor into the formation through the tubing. Kerver and Hanson8 studied the adsorption properties of inhibitors on various types of formations. They showed that, even though the inhibitor was displaced radially into the true permeability, it could be produced back for a long period of time because of slow desorption from the rock. Methods developed for monitoring the return of these inhibitors generally have established 1 to 6 months as the effective limit before retreatment is necessary.9 Inhibitors displaced into the interstices of the formation sometimes cause emulsions that either hamper production or cause treating problems on the surface.

By Benjamin C. Greene, H. Beecher Charmbury

Water is a most remarkable substance, essential for life of all kinds. As well as needing water to survive, man has always used it for agriculture, transportation, recreation, and many other things. When our country was young and inhabited by few people, the streams, rivers, and lakes were able to provide all the clean water needed by man and take away all the wastes created. However, with our growing population and an ever-increasing demand for goods and services, the public, industry, and government at all levels have become acutely aware of the need to manage the nation's water resources more efficiently. Abundant energy from many sources has helped this nation to become the greatest industrial nation in the world. Coal has contributed a major portion of this energy, generating electricity, running railroads, and maintaining national security during wartime. The result has been the highest standard of living in the world and a time of widespread economic prosperity. The use of water in coal mining is somewhat different from its use in most industries. With the exception of water used in cleaning plants, for underground dust control, and for fire protection, most of the water en- countered in coal mining operations serves no useful purpose. In other words, it is an undesirable element and must be removed, otherwise it will interfere with operations, cause potential water quality problems, and may even stop operations by flooding. In the past, removing water from working areas of most mines was usually a fairly simple matter. Pumps with piping were installed at sumps or low spots in the mine and the water was pumped to the surface or to drainage control facilities constructed for the operation. Ditches were often used to collect and drain the water by gravity to the outside or to main sumps for pump discharge. In either case, the water was allowed to flow into the nearest stream or river. The concept of "water is water'' was generally accepted without too much concern for what was in

Jan 1, 1981

By J. S. Johnson, W. C. McCulloch

ALL phases of plant operation must be synchronized so that the number of interruptions in the flow of material may be reduced to a minimum. In the majority of plants operating under a labor agreement, time lost during the operating shift cannot be made up with overtime. With the work week restricted to 35 hr., the ratio of productive time to total time justifies extra effort in keeping the plant operating at capacity during the productive shift. This does not apply when central plants with adequate storage are operated by multiple shifts. In such installations the problems become similar to those of any factory or mill where added units parallel circuits, or excess capacity serve to maintain the average production during intervals of maintenance shutdown. These plants, by special agreement, may run continuously, barring mechanical interruptions. The control of plant operation is in those procedures that are practiced to obtain from the run-of-mine product a high recovery of clean coal products to meet adopted trade standards and consumer specifications at the lowest possible cost. Correlation of all factors for continuous operation requires more than mechanical perfection in the plant. The run-of-mine coal must be delivered to the preparation plant without delays and the clean coal and refuse products taken away. Power supply and water requirements must be adequate. Signal systems must be established for emergency stops and to facilitate resumption of coal flow. ORGANIZATION Probably the most important item for successful operation of a preparation plant is a capable organization interconnected with the mine organization. A typical organization chart for companies operating in the Pennsylvania anthracite region is shown in Fig. 1. The breaker foreman is in direct contact with the plant preparation operation and reports to the outside foreman, who, in turn, reports to

Jan 1, 1943

By Benjamin C. Greene, H. Beecher Charmbury

Water is a most remarkable substance, essential for life of all kinds. As well as needing water to survive, man has always used it for agriculture, transportation, recreation, and many other things. When our country was young and inhabited by few people, the streams, rivers, and lakes were able to provide all the clean water needed by man and take away all the wastes created. However, with our growing population and an ever-increasing demand for goods and services, the public, industry, and government at all levels have become acutely aware of the need to manage the nation's water resources more efficiently. Abundant energy from many sources has helped this nation to become the greatest industrial nation in the world. Coal has contributed a major portion of this energy, generating electricity, running railroads, and maintaining national security during wartime. The result has been the highest standard of living in the world and a time of widespread economic prosperity. The use of water in coal mining is somewhat different from its use in most industries. With the exception of water used in cleaning plants, for underground dust control, and for fire protection, most of the water en- countered in coal mining operations serves no useful purpose. In other words, it is an undesirable element and must be removed, otherwise it will interfere with operations, cause potential water quality problems, and may even stop operations by flooding. In the past, removing water from working areas of most mines was usually a fairly simple matter. Pumps with piping were installed at sumps or low spots in the mine and the water was pumped to the surface or to drainage control facilities constructed for the operation. Ditches were often used to collect and drain the water by gravity to the outside or to main sumps for pump discharge. In either case, the water was allowed to flow into the nearest stream or river. The concept of "water is water" was generally accepted without too much concern for what was in

Jan 1, 1981

By C. W. Washburne

Continued discussion of the paper Of ROSWELL H. JOHNSON, presented at the New York meeting, February, 1015, and printed in Bulletin No. 98, February; 1915, pp. 221 to 226. See also Bulletin No. 101, May, 1915, pp. 1157 to 1162, and No. 103, July, 1915, pp. 1449 to 1450. C. W. WASHBURNE, New York, N. Y. (communication to the Secretary*).-Mr. Johnson recognizes that connate waters must be driven, outward toward the earth's surface. He considers the ascent due to the settling and packing of the underlying sediments and to the formation of gas within the rocks, supplemented by abyssal pressures. The origin of the methane in the sedimentary strata probably is not simple. There are three possible modes of origin: (1) as marsh gas formed near the surface and entrapped in the sediments; (2) from abyssal sources; (3) by the decomposition of organic matter buried in the sediments. The abyssal source is generally negligible, and in all cases doubtful. The third origin is the most important in the gas fields. A fourth mode of origin, by the dissociation of liquid hydrocarbons, frequently has been suggested, but it is improbable, because crude oils are exothermic. Therefore they have no tendency, to split or decompose at low temperatures, as do endothermic substances, such as coal, which is geologically by the loss of methane, water, and carbon dioxide. This cannot happen to a hydrocarbon until its temperature of dissociation (" cracking point") is reached, which is over 250'.C. for the most easily cracked hydrocarbons and over 400° C. for others. Engler says that the dissociation of fats and waxes into oils is an endothermic process, thereby unconsciously nullifying his own theory of the dissociation of these substances at low temperatures. However, recently I have found reason to think that heat is liberated by the disruption of the molecules of fats and waxes, as it is in the molecular decomposition of the substances of wood, coal, etc. If this tentative opinion is correct, and Engler wrong, then it seems that the Engler-Höfer hypothesis of the origin of oil becomes not only possible, but even probable.

Jan 9, 1915

By B. W. Roberts, V. A. Phillips

A copper alloy containing- 25.5 at, pct Zn and 19.0 at. pct Ni, which was previously found to show an anoma1old.s hardening effect on quenching- from 600 "C and aging- at 400oc, has now been examined by neutron diffraction. No evidence of long-range order was found. The aged sample showed diffuse scattering- consistent with clustering. The anomalous hardening effect is now attributed to lattice strains caused by clustering rather than (long-range) order hardening. SOLID-solution Cu-Ni-Zn alloys (the commercial 'nickel silvers") have been reported to show anomalies in: change of resistivity on cold working,1-6 temperature coefficient of resistance,2-12 resistivity at low temperatures,13,14 parameter (vs temperature),2"4 calorimetric data,2,4 specific heat,15,16 dilation,2-4 and elastic modulus.17 The structure responsible for the anomalies is produced by annealing typically near 400°C and is rather loosely referred to as the ('K-Zustands" (K state), a term coined by Thomas1' who apparently meant simply that the arrangement of atoms on the sites deviated from that expected statistically. Thomas proposed that the K state occurred in a variety of (solid-solution) alloys such as Cu-Ni-Zn, Ni-Cr, Ni-A1, Ni-Cu, Fe-A1, and Fe-Si and is recognized because its formation is strongly temperature-dependent and results in an increase in electrical resistance which can then be decreased by cold working. Later workers on ('nickel silver" have interpreted the K state variously as short-range order, long-range order. or a combination. The present work was prompted by the discovery by Phillips and Jones19 of a substantial hardening effect when an 18 pct "nickel silver" alloy which is fairly close to the Cu2NiZn composition, was reheated in the range 150" to 450 C after previously quenching from 600°C or, alternatively. was slow-cooled from 600°C or above. The phenomenon was attributed to (long-range) order hardening. Due to the similarity in the atomic scattering factors of copper. nickel, and zinc atoms, the ''nickel silvers" are unfavorable for X-ray diffraction studies aimed at detecting ordering. Nevertheless Bialas et a1.,20 using a powder sample containing 47.96 wt pct Cu, 24.03 wt pct Ni, and 27.98 wt pct Zn, slow-cooled from 400" to 200°C taking 500 hr, observed weak super lattice lines. Further unpublished work" using an anomalous dispersion X-ray technique indicates that zinc atoms are regularly ordered at the corner points of the lattice cell, while the nickel and copper atoms are statistically distributed on the remaining sites. Köster 17 also observed X-ray superlattice lines, for example, in an alloy containing 43.5 wt pct Cu, 28.6 wt pct Ni, and 27.9 wt pct Zn superimposed on the basic fcc cell with a = 3.62 kX. He proposed a Cu3Au-type superlattice with the Ll2 structure in which the A sites were statistically occupied by copper and nickel atoms and the B sites by zinc. He adds that substitution must be possible so that zinc atoms partly occupy A sites. Below about 35 pct Cu, Koster had some evidence for a CuAu-type superlattice with the Llo tetragonal fcc structure with a = 3.82 kX, c/a = 0.88 which could be preserved by quenching. This is suggested17722 to correspond to CuNiZn. While the present work was in progress Hirabaya-shi et a1.23 made an independent comprehensive neutron-diffraction study of a single crystal containing 50.05 at. pct Cu, 26.57 at. pct Ni, 0.25 at. pct Mn, 0.13 at. pct Fe, balance zinc. The presence of manganese and iron is surprising since the crystal was supposedly grown from high-purity metals. The homogenized crystal showed evidence of long-range ordering after an anneal of 5 months at about 300°C. Three possible crystal models were proposed. A curious feature of their results23 is that they could not find any neutron-diffraction evidence of ordering in a powdered polycrystalline near-stoichiometric Cu2NiZn alloy. There appears to be some essential difference between a near-stoichiometric Cu2NiZn alloy and one somewhat further off stoichiometry as used by the present authors. Thus Sato14 was able to reproduce the low-temperature resistivity anomaly reported by one of the authors13 on the present alloy if he used a similar composition, but found the normal behavior of the residual resistivity in a near-stoichiometric alloy. satol2 found that the resistivity of a cold-drawn slightly off-stoichiometric alloy increased to a maximum on isothermally annealing at 300°C and then decreased ("over-aged"). Since he could not explain this on the basis of ordering phenomenon, he proposed that zinc atoms were segregating to stacking faults (Suzuki effect) and found etching bands on the surface by replication which were attributed to the widening of faults. Sato suggested14 that the hardening effect observed by Phillips and Jones19 is partly due to the Suzuki effect. EXPERIMENTAL The starting material was 1/4-in.-diam hard-drawn rod of a commercial 18 pct "nickel silver" alloy identical with that used in a previous study by Phillips

Jan 1, 1967

By R. T. Southin

Cast ingots of 99.99 pct purity A1 and aluminum/copper alloys containing up to 2 pct Cu have been found to contain four zones rather than the three previously accepted, i.e., chill, colummar, and equiaxed zones. The fourth zone consists of a coarse dendritic layer across the top surface of the ingot which is open to the atmosphere. It is also found that the grains in the equiaxed region have a "cornet" shape, with a head which is coarsely dendritic and a tail which grew with the same structure as the columnar grains. Experiments using mechanical barriers, and others involving the elimination of the surface dendrile layer, have indicated that nucleation of the equiaxed zone is caused by the showering of dendritic particles from this surface dendrite layer. These particles are the dendritic heads found in the comet grains. A mechanism of nucleation and growth of these comet grains is put forward. Experiments with a number of other metals and alloys suggests that these conclusions may apply generally to ingots cast without the addition of nucleating agents, and solidified under normal conditions. THE macrostructure of cast ingots may contain the following three zones: i) a peripheral zone of fine equiaxed grains, commonly called the chill zone; ii) a zone of columnar grains extending inwards from the chill zone; iii) a central zone of equiaxed grains; these are normally larger than the chill grains. All three zones are not necessarily present in any particular ingot since their existence and magnitude depend upon the casting conditions and composition of the cast material. The mode of formation of zones i and ii is fairly well understood. However, the cause of the central equiaxed zone remains a matter of conjecture. Previous theories put forward to explain the mechanism of nucleation in the equiaxed zone have been examined by Chalmers1 and Winegard.2 At the time when the present work was carried out the most re -cent hypothesis was that due to Chalmers,1 who recognized more fully than previous workers that conditions in this zone during solidification were not conducive to nucleation. In his hypothesis, he suggested that nuclei were formed near the mould wall during the very early stages of solidification, and that they can drift into the central zone by convective motion. This was supported by evidence from experiments using mechanical barriers to stop the drift of nuclei. A similar hypothesis had previously been put forward by Genders.3 More recently, Jackson et al. 4 have observed that dendrite arms in organic compounds can melt off during solidification. They have postulated that this occurs in metals and alloys, and that the dendrite arms which have been freed from the main dendrite act as nuclei for the equiaxed zone. In the present work, critical metallographic examination has shown that there is a fourth zone in the macrostructure of cast ingots which is a dendritic layer over the top surface of the ingot. It is also shown that there is a relationship between this zone and nucleation of the equiaxed zone. EXPERIMENTAL DETAILS The alloys examined were prepared from super -purity aluminum of 99.99 pct min purity (spectro-graphically detected impurities of Cu, Fe, Si, and Mg) and copper of 99.98 pct min purity (spectrographically detected impurities of Si, Zn, As, Fe, Pb, Bi, Ni, Sn, Mn, Ag, Cr, and Al). Three compositions of ingots were examined, containing 0.0, 0.1, and 2 pct Cu, respectively. The alloys were melted in an alumina-lined salamander crucible using a medium-frequency electric induction furnace; when the appropriate casting temperature was reached, the alloys were cast without degassing or fluxing treatment. The mould used was made of electrode graphite and had the following dimensions: external diameter 6 in., height 9 in., with a mould cavity 8 in. deep and a diameter tapering from 5 in. at the top to 4 in. at the bottom. Casting temperatures used were generally in the order of 70" to 90°C above the liquidus and the mould was at room temperature before casting. Inserts kere placed in the mould cavity in some experiments. These consisted of either an 18-g stainless-steel tube of 2 in. diam held axially in the mould i in. off the bottom and extending 1 in. out of the top of the mould or a "trap-door" barrier of stainless-steel gauze of 24-mesh held horizontally in the mould 31/2 in. down from the top. The construction of this insert is shown in Fig. 1. All inserts were preheated prior to casting to prevent chilling. RESULTS The macrostructures of ingots of the three compositions are described, in terms of the three generally recognized zones, in Table I, and illustrated in Figs. 2(a) to (c). The most interesting observation in this table is that relating to the shape of the equiaxed grains, which were not in fact equiaxed but of almost tear-drop shape. Closer examination of these grains showed that each consisted of a head which had a coarse dendritic structure and a tail which always grew in the opposite direction to heat flow, and which had the same structure as that of the columnar material of the ingot concerned; i.e., in the pure aluminum and 0.1 pct Cu alloy it was cellular and in the 2 pct Cu alloy it was cellular-dendritic. Identification of original cast grains was greatly hampered in the super-purity aluminum ingots, and to a lesser degree in the 0.1 pct Cu alloy,

Jan 1, 1968

By William D. Klopp, Joseph R. Stephens

ThE phenomenon of high ductility associated with a phase transformation, termed super plasticity, has been reported for a number of alloy systems. Abnormally high ductility has been observed during tensile testing of cast eutectic alloys of Pb-Sn and Mg-cu.1 Brasses of Cu-37 at. pct Zn and Cu-40 at. pct Zn elongate up to 180 pct when tested near their transformation temperature.' Enhanced ductility was also observed in Cu-47 at. pct Zn tested near the order-disorder transformation temperature. The most remarkable super-plastic effect reported to date is for the eutectoid alloy A1-60 at. pct Zn, where elongations up to 1000 pct have been reported.3 underwood4 has recently summarized the conditions that normally accompany the superplastic effect which are: 1) a phase transformation or allotropic change or order-disorder transformation; 2) an externally applied stress; 3) presence of an interface between two phases; and 4) a metastable structural condition. In addition, higher ductility is observed when the specimen is tested at slow deformation rates rather than under impact. The purpose of this note is to present evidence of the superplastic effect in a Cr-30 at. pct Co alloy. In addition, low-temperature bend ductility data are given for the alloy in the quenched, metastable, single-phased condition and in the slow-cooled, two-phased, near-equilibrium condition. Sixty-gram alloy ingots were prepared by noncon-sumable arc melting of iodide chromium and electron-beam-melted cobalt. These were cast into rectangular ingots and fabricated to 0.035-in. sheet by rolling at 2300°F. Attempts to roll at slightly lower temperatures invariably resulted in severe cracking, apparently due to presence of the brittle a phase below the transformation temperature of 2230°F. Tensile specimens with a 0.25 by 1.0 in. reduced section were cut from the sheet by electrical discharge machining. The specimens were heated at 2400°F for 1/2 hr to obtain a recrystallized, bcc, single-phased structure. Temperature of the specimens was subsequently raised or lowered to the desired test temperature and held for 10 min prior to testing at a crosshead speed of 0.01 in. per min. Fig. 1 shows the chromium-rich side of the Cr-Co phase diagram.6 The alloy composition investigated is near the point of maximum solubility of cobalt in chromium, and the alloy is two-phased when in equilibrium at temperatures below 2230°F. The results of tensile tests conducted at temperatures indicated by X's in Fig. 1 are summarized in Figs. 2, 3, and 4. Tensile elongations shown in Fig. 2 increase from 11 pct at 1900°F to a maximum of 160 pct at 2250°F. The elongation then decreases to 44 pct as the test temperature is further increased to 2600°F. The proximity of the temperature of highest elongation and the solvus temperature suggests that a superplastic effect is present in Cr + 30 at. pct Co similar to that observed for other alloys that show anomalous ductility. The variation of upper yield stress with temperature is shown in Fig. 3. A small peak in yield stress occurs at 2250"F, coincident with the maximum in

Jan 1, 1967

By P. L. Rittenhouse, M. L. Picklesimer

A rapid and seniquantitative method of determining prefered orientation on large numbers of. Zircaloy-2 specimens was desired. knoop microhardness measurerrzetzls were irvestigated as a solldtion to this pro6lem. The variation of Knoop microhardness measurerlerzts on selected planes as a function of 'irzdenle axis relutilje lo cryslallograplzic or fabrication divectals were used to corzstrrcl a polar coordinate hardness contour map. With use of an empirical relationslip between the single-crystal hardnesses and those of the polycrystalline material conentional pole figures could be constructed which compare favorably also obtained. To determine preferred oriention qualitatively from hardness data requires a minimum of twelve measurements per plane on three, preferattention to grain size, specimen prepartion, and in-rreinetzt, and analjlsis is of the order of- 45 to 60 rrin. THE design of structures from Zr alloys requires consideration of preferred orientation and the resulting anisotropy of mechanical properties. Rapid and semi-quantitative methods of evaluating anisotropy and of determining preferred orientation are needed for quality control and for examining the large number of test specimens required in development programs. The variation of Knoop microhardness with indenter orientation has been studied in single crystals of several hcp metals including titanium.' beryllium,' magneium, and zinc.4 The maximum hardness observed on any crystallographic plane other than the basal plane invariably occurred when the long axis of the Knoop indenter was either parallel or perpendicular to the projection of the [ OOOI.] direction on the plane of examination. When the major slip mode was (0001)(i2i0j the maximum hardness occurred at the parallel positio! but when the operating slip system was {10i0) (i210) the hardness was a maximum perpendicular to the [0001] projection. A minimum hardness was always observed at a rotation of 90 deg from the maximum. It follows that the orientation of the projection of the [0001] can be determined on any non-basal plane by making hardness measurements at a number of indenter orientations. The determination of the orientation of the [0001] projection on two non-parallel, preferably orthogonal, surfaces of the specimen will allow location of the [0001] direction in the specimen. It seems possible that such measurements could be used to examine, at least qualitatively, the preferred orientation existing in polycrystalline hcp materials. An investigation of the microhardness anisotropy in Zircaloy-2 was undertaken to ascertain whether these measurements could be used for this task. EXPERIMENTAL PROCEDURE Single crystals of Zircaloy-2 were grown by an a-8-a annealing sequence using electron-beam heating.= The orientation of the crystals was determined by a conventional back-reflection Laue technique. The crystals were then mounted on a goniometer head and the desired crystallographic faces were milled and chemically polished. Polycrystalline Zircaloy-2 specimens were prepared from fabricated sheets or plates. Inverse pole figures for these materials were obtained using the X-ray diffraction techniaue described by Jetter, McHargue, and illiams.' A Wolpert-Greis Micro-Reflex hardness-testing machine was used to make the Knoop microhardness measurements. The single-crystal and polycrystalline specimens were loaded to 0.5 and 2.0 kg, respectively. Determination of the scatter of hardness numbers as a function of applied load for several indenter orientations on several specimen surfaces showed that the loads selected were the lightest consistent with minimum scatter. Heavier loads did not appreciably decrease the scatter and produced hardness impressions too large to be conveniently measured with the equipment used. Seven crystallographic planes of the single crystals were examined, while six planes of examination were used in studying Zircaloy-2 polycrystals. The specimens were rotated 10 to 15 deg after each measurement and from four to eight impressions were made at each angle of rotation. RESULTS The two angles which were used to relate crystallographic directions and planes in the hcp cell to the planes of examination of the single crystals are shown in Fig. 1. 8 is the angle between the c axis. [0001]. and the normal, N, to the plane of examination. a is the angle between the long diagonal of the Knoop indenter and the projection of the c axis on the plane of examination. For exampIe, if P = 90 deg and a = 0 deg, the plane of examination is of the family

Jan 1, 1967

By F. Keller, A. H. Geisler

Some of the important changes that take place in the structure of aluminum alloys are largely submicroscopic in character. This is especially true of the changes that accompany age-hardening and recrystallization. Although improved metallographic practices have been helpful in indicating some of these changes indirectly, results are limited by the resolving power of optical microscope lenses. The electron microscope, however, provides a new and important means for investigating the fine structure of metals in a range not possible heretofore. It is anticipated that this microscope will yield new and useful information to metallurgists when suitable techniques are developed to utilize its very high resolving power. Several unique methods have been devised to permit the examination of the structure of opaque samples by the electron microscope. These are all based on the principle of producing a very thin film that represents the prepared surface of the opaque metal sample, which can be examined in the transmission microscope; however, the available methods fall into three categories, depending on the manner in which the film is obtained. With the oxide-film method developed by Mahl3-17 a very thin surface layer of the metallographic sample is converted into oxide by a thermal, chemical or anodic treatment. After removal from the metal sample by one of the special techniques described by Evans,19 this oxide film is examined in the electron microscope, and is found to portray the structure of the original metal surface. Films formed on aluminum,8,17 nickel,7 iron 3,8,9 and a nickel-beryllium alloy" by heating; films formed on iron 8.9 by chemical action; and films formed on aluminum3-16 by anodic oxidation, have been examined. The other two are more recent methods developed principally in this country; they consist in making the thin film in the form of a mold or replica of the surface contour of an etched sample. With the negative replica method the thin film is made directly on the sample; with the positive replica method it is made on a negative reproduction of the sample. With both methods, variations in the contour of the metal sample, caused mainly by etching, produce variations in the thickness of the surface replica. Because of the direct dependence of the amount of scattering of the illuminating electrons upon the thickness of the film penetrated, only the variations in thickness of the replica are responsible for tones in the electron image. Negative replicas are made by forming a thin film of some suitable material directly on the polished and etched metal sample, and derive their name from the fact that after removal from the sample they have the high and low points in the sample reversed, as shown in Fig. I. Nega-

Jan 1, 1944

By R. M. Brown, W. J. Murphy, B. M. Kapadia

An investigatiott was conducted to study the influence of nitrogen, titanium, and zirconium on the boron llardenabilzty effect in a low-carbon constructiona2 alloy steel. The experimental steels investigated exhibited a significant variation in hardenability, the variation being dependent on the interactions of boron, titanium, and zirconium with the nitrogen. Only the boron not combined with nitrogen was effective in increasing hardenability. Titanium, and with lesser effectiveness zirconium, combined with available nitrogen, thereby protecting the boron. The hardenabil-ity effect mas related to an empirical expression for the "effective" boron content, P, deduced from experimental evidence of these interactions. The hardenabzlity effect reached a maximum at about 0.001 wt pct 0, and decreased somewhat as P increased further. The physical understanding of this relationship is discussed. FOR many years boron has been added to steels to obtain high hardenability. Although a great deal of research has been conducted on boron-treated steels, certain aspects of the boron hardenability effect have not been fully understood. For instance, the magnitude of the hardenability effect has been observed to vary markedly, depending on the steelmaking technique, even when the amount of boron in the steel was essentially constant. Furthermore, the optimum amount of this element to be added has not been definitely established. A better understanding of the boron hardenability effect is essential because too small an addition of boron is likely to be ineffective, while an excessive amount can cause brittleness'' and hot shortness. The findings of earlier investigations have shown that the hardenability effect cannot be consistently related to the amount of boron added or retained in the steel. Grossmann observed that in a 0.60 pct C steel the hardenability increased to a maximum with mold additions up to about 0.0025 pct B and then decreased with larger additions. Other investigators5 likewise reported a maximum in the hardenability at about 0.003 pct B. Crafts and Lamont, however, found that in commercial open-hearth heats of medium-carbon steel the hardenability increased linearly with boron up to 0.001 pct and remained essentially unchanged with larger percentages up to 0.006 pct. Other investigators7,' also observed a rather constant hardenability effect in the range about 0.0005 to 0.0035 pct B. These observations and other evidence suggest that the effectiveness of boron in increasing hardenability probably depends, in addition to the amount, on the form of boron retained in the steel, this form being influenced by the presence of other elements. Both oxygen and nitrogen apparently exert the strongest influence on the hardenability behavior, since, at the temperature of liquid steel, boron readily combines with these elements, thereby losing its effectiveness as most experimental evidence seems to indicate. For consistent recovery of the boron effective in increasing hardenability, it is necessary that the oxygen and nitrogen in the steel be either reduced to extremely small amounts by the steelmaking practice or neutralized by combination with other elements before the addition of boron. The importance of achieving adequate deoxidation prior to the addition of boron in order to realize the full hardenability effect of boron has been sufficiently emphasized by earlier investigators. Digges and Reinhart' and others have investigated the role of nitrogen and have shown that nitrogen also interacts with boron and reduces or nullifies altogether its effect on hardenability. Moreover, their work also demonstrated that the addition of strong nitride formers such as titanium and zirconium reduce the deleterious effect of nitrogen on boron hardenability by combining with nitrogen to form stable nitrides. Another element which has a pronounced influence on the boron hardenability effect is carbon. It has been shown7'10 that the hardenability effect of boron diminishes with increasing carbon content, and becomes almost negligible at the eutectoid composition. This observation is useful in comparing the potential increase in hardenability from boron of steels with different carbon contents, but is not relevant to a study of the effects of normal steelmaking variables. The amounts of oxygen and nitrogen in steel vary with the steel composition and steelmaking practice employed. Most commercia1 low-alloy steels are fully deoxidized by the addition of silicon and aluminum, or other strong deoxidizers, which adequately protect the boron from oxidation. In addition, one or more of the elements such as titanium or zirconium are usually added, either separately or in combination with boron, in the form of complex ferroalloys, to protect boron from combination with nitrogen in the steel. However, the actual amount and type of addition employed for a given processing requirement are usually selected by trial and error, and have a rather limited range of applicability. As a result, substantial variations in the hardenability of boron-treated steels are often observed in practice, particularly when the nitrogen content of the steel is a significant processing variable. These variations might therefore be reasonably attributed to the interactions between boron, nitrogen, and titanium or zirconium present in the

Jan 1, 1969

By G. T. Hahn, C. N. Reid, A. Gilbert

An evaluation is made of the possible cautsal relationship between twinning and fracture in molybdenum. For both single and poly crystalline material no instance of twin-induced fracture was observed. Instead brittle fracture was found to be slip-induced at heterogeneities. For single-crystal material, the yield stvess in compression and the fracture stvess in tensiow obey a similar angular- relationship which follows approximately a 1/cos2 ? law. where 0 is the angle between the specimen axis and the nearest (100) plane. This sittlilarity between yield and fracture behavior casts doubt on the interpretations made previoltsly that a 1/cos2? relationship supports a critical normal fracture stress criterion. SINCE fracture in brittle materials takes place at stresses an order of magnitude lower than the theoretical strength of the lattice, it must be postulated that some stress-concentrating effect is operative during the fracture-initiation process. Several mechanisms have been proposed whereby the necessary stress concentrations could be produced. The well-known Cottrell mechanism1 describes a dislocation interaction which can lead to the formation of an incipient cleavage crack on a cleavage plane, and both zener2 and stroh3 have discussed models which predict the stress concentration at the intersection of a slip band with a grain boundary. When twinning occurs twin/twin intersections and twin/grain boundary intersections represent another possible means of fracture initiation. Although still controversial, the concept of twin-induced fracture is supported by a weighty mass of evidence, which has been reviewed in a recent paper.4 This investigation was conducted in order to assess the extent to which the brittleness of molybdenum can be ascribed to this cause. Emphasis was placed on seeking direct metallographic evidence for twin-induced fracture such as arrangements of twins located at the fracture origin. EXPERIMENTAL PROGRAM Materials. The experimental materials are described inTable I. From the chemical analyses and estimates of the amounts of interstitials likely to be retained in solution,5 it is concluded that all were mul-tiphased systems. X-ray diffraction experiments6 showed no evidence of preferred orientation in the polycrystalline materials. Single crystals were grown from Molybdenum X and Y using the floating-zone technique,' in a vacuum of better than 3 x 10-5 Torr. However difficulties were experienced with Molybdenum X due to violent gas evolution from the molten zone, and additional crystals (Crystals 3 to 6) were produced by annealing for 5 1/2 hr at 2300°C under a vacuum of 10-4 Torr. Techniques. A series of tension, compression, and bend tests was conducted. Tension tests were used to demonstrate brittle behavior, to measure brittle-fracture stresses, and to provide fractured specimens for metallographic inspection. Compression tests were employed in order to obtain some ductility and a measure of the yield stress. Furthermore, it was considered that compression loading would permit the study of crack nucleation in the absence of propagation. The bend tests were conducted to facilitate identification of the fracture origin, which would be expected to be at, or near, the tensile surface of the sample. Tests were carried out at temperatures between 78" and 298°K attained by means of a liquid-nitrogen evaporator of modified Wessel design.' Specimens were fashioned by mechanical grinding, and, prior to heat treatment, were electropolished at 10 v in a 3:l mixture of ethyl alcohol and sulfuric acid, using a stainless-steel cathode. Except where noted, a strain rate of 4 pct per min was used. All specimens had a gage section 0.75 in. long; diameters of 0.10 and 0.20 in. were adopted for the tension and compression specimens, respectively, the former of single shoulder design, the ends being gripped in split collets with a conical bearing surface. In the bend test, electropolished specimens measuring 0.080 by 0.25 by 1.25 in. were deformed at 78°K by four-point loading. The bending device had spans of 1 in. between the outer and 4 in between the inner fulcra; it was stressed between the compression anvils of the Instron machine at a constant deflection rate. EXPERIMENTAL RESULTS Polycrystals. Tension and Compression Tcsls. It is apparent from Fig. 1(a) that above 170°K fracture of Molybdenum X takes place at stresses equal to or greater than the compressive yield stress whereas

Jan 1, 1967

By F. Bonaccorso, G. Venturello, C. Antonione

A study of the effect of small amounts of interstitial impurities on recovery and re crystallization in high-purity iron (99.995 pct) has been undertaken. This paper gives results on the effect of carbon, introduced in small-dosed amounts @om 0.0005 to 0.0086 wt pct) by heating iron specimens of high purity m a static atmosphere of CO + ,. The materials prepared in this way, cold-worked 80 pct and subjected to a series of isochronal and isothermal annealings, were submitted to examinations by X-rays, micrographs, and hardness tests. It was observed that effect of carbon is remarkable in the sense of blocking recovery of mechanical properties up to the temperature at which re crystallization begins. On the contrary, carbon has a negligible effect on primary re crystallization temperature, when compared with the known effect of substitutional impurities. This is in agreement with the high mobility of interstitials. In effect, only a slight decrease, -20 pct, of the grain-boundary motion rate was noted, due to the interaction between the grain boundary and the carbon atoms. On the other hand, in the samples in which the carbon content is above the solubility limit at the temperature at which re crystallization occurs, a slight increase of nucleation frequency is noted due to the presence of precipitated carbides. ThE effect of purity on recovery and recrystalli-zation phenomena has been known for a long time; however, recently, new attention has been given to the problem since new methods for obtaining metals with extremely low impurity contents have become available. Most of this research work essentially concerns the effects of impurities which cause precipitates or give rise to substitutional solid solutions. The works of Bolling and winegard1 and Aust and utter' on lead, and Vandermeer and orddon' on aluminum, 01sen4 on nickel, and Abrahamson and Blakeney on iron should in particular be referred to. On the effect of this type of impurities a quantitative theory has been formulated by Detert and Lucke6 and has lately been discussed critically by Cahn7 and Gordon and vandermeer.' Interstitial solid solutions in iron have not as yet been studied. As the study of the effect of interstitials is of great interest both from a theoretical and practical standpoint, it was deemed useful to examine the effects of carbon, nitrogen, and boron on recovery and primary recrystallization of iron. There already is some work by Chaudron et al.,1-" on the effect of interstitials on iron; their work, however, mainly concerns secondary recrystallization. The present paper refers in particular to the effect of carbon. EXPERIMENTAL PART Preparation of Materials. The pure iron used for this research was obtained from FeCIS recrystal-lized and purified by extraction with isopropylic ether. From the ferric chloride purified in this manner, hydroxide was precipitated with a solution of very pure ammonia, and, by calcination in pure sintered alumina crucibles, oxide was obtained. Reduction of the oxide to iron sponge was performed in sintered alumina tubes with very pure hydrogen at 650°C; at the end of the operation temperature was increased to 900°C. Specimens for the experiments were obtained by sintering the sponge at 1480°C in pure Hz after a pre sinter ing treatment at 900° C. It is important to note that the treatment at 1480°C in Ha produces a further purification from more volatile elements such as zinc, cadmium, arsenic, lead, and tin. Details on the preparation and characteristics of this type of very pure iron are given in a previous work.'' Only the complete analysis performed by neutron-activation methodsz3 is given here, Table I. Some of the specimens prepared in this way were carburized in the 0 region with very low amounts of carbon by treating them at 700°C in a static atmosphere of Ha containing a definite amount of CO. The set-up used is described in Fig. 1. A gas-tight quartz tube containing the specimen to be carburized and an internal friction control specimen, after being evacuated, was filled with Hz

Jan 1, 1963

By Henry J. Williams

The main difficulty in the determination of silicon in pig-irons containing very high percentages of that element, has been due to their almost complete insolubility in acids, or mixtures of acids. The object of the present paper, which presents no new principle, is to suggest a method of determination which has repeatedly given accurate results, and which obviates completely the tediousness and uncertainty of the usual slow solution in acids. This method has been tried with pig-irons containing from 7 to 14 per cent. of combined silicon, and properly called ferro-silicons. When reduced to an impalpable powder in the agate mortar, an 11 per cent. ferro-silicon was found to resist the action of all acids, or mixtures of acids, with the exception of sulphuric acid of about 1.25 specific gravity. But the action of this acid, even during long continued heating, was very slow, 72 hours being necessary to com pletely dissolve half a gramme of the metal. The complete decomposition of 1 gramme of the metal may, on the other hand, readily he effected in a few minutes by fusion with sodium carbonate in a covered platinum crucible over a blast-lamp —the idea being to dissolve the silicon, leaving the iron in condi tion to be readily attacked by acids. The silicon dissolves as soluble sodium silicate, and metallic iron remains in a very spongy and finely divided condition. The addition of a little hot water

Jan 1, 1889

By Jack A. Simon, M. E. Hopkins

GENERAL GEOLOGY Coal is defined as a combustible rock that originated in the accumulation and physical and chemical alteration of vegetation. Coal can be ignited and burned like the wood that was man's earliest fuel, but coal gives more heat than the same amount of wood and has many industrial uses. Unlike wood, coal is not generally found on the surface of the ground but is mined from the solid rock of the earth. Before taking up the occurrence, formation, and the unique character of coal in the rock sequence, let us briefly consider the general character of all rocks in the crust of the earth. Relatively little is known about the very earliest history of the earth, although a number of logical theories have been developed. Manned exploration of the moon and the rocks returned to earth continue to provide some answers to questions concerning the earth's origin and history. The period of earth history with which we concern ourselves here begins after great areas of water had evolved on earth and substantial land areas of once molten (igneous) rock existed. Weathering and other processes that attacked the surface of the rocks reduced them to small particles. Water provided by rainfall transported this material, ultimately, to large bodies of water where it was deposited. Thus was initiated the geologic sequence of sedimentary rocks that lie above the once molten igneous rocks. The crust and upper mantle of the earth are made up of several large plates along which differential movement (primarily horizontal) takes place. Such movements, although small, are occurring today. These horizontal movements are accompanied by vertical movements causing important changes in the relative position of the continents and oceans. Low-lying coastal swamps with favorable climates are ideal locations for coal accumulation and burial by river-borne sediments, and large areas

Jan 1, 1981

By M. Deighton, R. N. Parkins

The metals Cd, ,Wg-, Sn, TI, Zn, and Zr reach a peak hardness after a criticfir1 deformation by rolling- and then soften with fwther rolling-, thereby exhibiting wovk softening. Optical metallography on Cd, Mg, and Zn shows that work softening is accompanied by a change in grain size occurring during deformation. The creep of zinc from -1l° to +60°C at stresses in the range of 7.9 to 17.3 kg per sq mm is given by € = e0 -t- Bt + Kt +at6. The third and second rate constcints are related by the equation a = K~ K6 and their stress and temperature dependence can be represented by the equations K = A, . exp - (u, - Bu)/kT. A model based upon the stress activated glide of sub-boundaries is proposed which qualitatively accounts for the metallog-raphic observations. Expressions, which are in reasonable quantitative agreement with the ex-pe~inzental observations, are derived for the creep of zinc. THE term "work softening" has been used previously by Polakowski1 and by Cottrell and stokes2 to describe phenomena where further strain of a deformed material leads to a decrease in flow stress. In both cases, however, the conditions were changed for the second straining. Here, the term "work softening" is intended to refer to a decrease in flow stress after continued straining in the same direction at the same temperature: work softening is the antithesis of "work hardening". Work softening of zinc was reported by chadwick3 and in discussion of that paper Jenkins4 indicated that cadmium also work softens. More recently work softening has been reported5 in two magnesium alloys, -99.5 pct Mg. Chadwick found that the hardness, 0.2 pct Proof Stress and the UTS of electrolytic zinc all increased with progressive cold reductions up to 30 pct and then progressively decreased with further rolling. Gay and Kelly6 used a back-reflection X-ray technique to study the effect of cold rolling zinc and found that although deformations greater than 2 to 5 pct reduction in thickness produced some recrystallized grains, deformations greater than 40 pct caused com-plete spontaneous recrystallization. At deformations greater than 60 pct the material was found to consist solely of recrystallized grains, -20 pm diam, the size of which decreased with increasing reduction and was much less than the initial grain size of the annealed material (-300 pm diam). Similar results were also reported for cadmium, tin, and lead.6 Gay, Hirsch, and Kelly' suggest that these experiments indicate recrys-tallization takes place when the dislocation density exceeds a certain value. However, no measurements of MATERIALS AND EXPERIMENTAL PROCEDURE The purity of the metals used in this work is indicated by the following figures: Zn (99.99); Cd (99.94); Mg (99.95); T1 (99.99). The zirconium was iodide crys tal bar with a probable purity of about 98 pct. The metals were obtained in the form of 0.25 in. thick strip or 0.425 in. diam rod by various fabrication methods and then annealed to ensure complete re-crystallization. Hardness-deformation curves were obtained at room temperature by rolling 4 in. thick strip under conditions which left a surface adequate for diamond pyramid hardness tests immediately after rolling. The hardness was taken as the niean of five impressions made using a 5 kg load and the time elapsing between rolling and making the last impression never exceeded 5 min. The zinc specimens for creep testing were from 3 by 3 by 4 in. cast slabs which were rolled to 0.10 in. thickness starting at 350°C and finishing cold. The resulting strip was cut into pieces 1 in. wide and annealed in batches. With suitable choices of annealing temperature between 100" arid 400°C five different grain sizes varying from 4.54 x 10' to 3.03 x l05 grains per sq cm (530 to 20 um diam) were obtained. Creep tests were done in compression using a sub-press, based on a design after Ford,8 in which the strip is compressed between dies 0.100 in. wide under conditions of plane strain. Since there is no lateral spread of the material, the area of contact between the dies and strip remains constant throughout the test and the application of a constant load, using the load maintaining device of a hydraulic testing machine, resulted in a constant stress. Covering the dies with strips of P.T.F.E. reduced frictional effects to a minimum. The creep strain was obtained by measuring the travel of the crosshead of the testing machine to a sensitivity of 0.1 pct reduction in thickness. The complete subpress assembly was contained in a steel box and for tests above the ambient this was filled with liquid paraffin and heated electrically. Temperatures below the ambient were obtained with a cooling mixture of acetone and solid carbon dioxide in the box. The liquids were stirred and the temperature of the specimen, which was controlled to ±0.5"C dur-ing a test, was measured by a thermocouple placed near the dies. Compression testing of cylindrical specimens was also carried out in the subpress using hardened flat discs separated from the test material by P.T.F.E. sheets which obviated barrelling of the specimens. Various initial strain rates were supplied by the hydraulic testing machine, and the deformation was measured by a clock dial gage resting on the cross-

Jan 1, 1970

By N. S. Stoloff, R. G. Davies

The annealing behavior of a heavily cold-worked FeCo-V alloy has been studied at temperatures both above and below Tc, the critical temperature for ordering. It was found that re crystallization and grain growth can take place below Tc in the ordered state and that, in agreement with results for fcc alloys, order retards grain growth. The activation energy for pain growth is -55 kcal per mole in the disordered condition; it was not possible to assign a value to the activation energy for grain growth below Tc because the degree of order is changing rapidly over the temperature interval investigated. Precipitation of an fcc y phase was observed upon annealing the cold-worked alloy at temperatures of 675°C and below. SINCE it is known that diffusion constants are greatly affected by long-range order,' it is not unreasonable to anticipate that order will influence the diffusion-controlled phenomena of recrystallization and grain growth. In the course of a study of strain aging of ordering alloys around the composition Ni3Fe Vidoz, Lazarevic, and cahn2 noted that a disordered cold-worked alloy annealed at a temperature T1 just below Tc will order but not recrystallize; Tc is the critical temperature for order. The same alloy annealed at a temperature T2 just above Tc, or an alloy of different (nonordering) composition annealed at either T1 or T2, will recrystallize after equivalent amounts of cold work. Initially Selisskii and coworkers,3,4 who examined a series of cold-worked and annealed bcc Fe- Co alloys, reported that alloys forming the B2 FeCo super lattice could not be recrystallized below Tc. However in a later paper5 it was shown that FeCo ordered alloys could be recrystallized below Tc. Thus the first question to be answered by the present investigation was whether or not a heavily cold-worked Fe-Co-V alloy could be recrystallized below Tc. When it was found that the alloy would indeed re-crystallize below Tc, the influence of long-range order upon subsequent grain growth was studied. EXPERIMENTAL PROCEDURE The grain-growth measurements were made upon FeCo-2 pct V wire of 0.031 in. diam; the alloy was the same as that used in an earlier study of the mechanical properties of FeCO-v.6 The wire was produced by cold swageing and drawing a rod 0.125 in. diam that had been quenched into iced brine from 850°C to disorder the alloy; the initial grain size was 0.05 mm. Rates of grain browth were measured after isother-mally annealing the wire in the temperature range 675° to 825°C; T, is -720°C. Grain diameters were measured on the transverse cross section of the wires. The line-intercept method of determining the grain diameter was used; conventional light photomicrographs were taken when the grain size was greater than 10 . Carbon replicas were produced and examined in the electron microscope if the grain size was less than Dislocation configurations after recrystallization anneals were studied by electron transmission microscopy of foils produced by cold rolling a 0.125-in.-thick strip of the quenched material to 0.012 in. The foils, after heat treatments similar to the wire samples, were thinned by electropolishing in a chromic-

Jan 1, 1967