Search Documents

By T&apos Ke, ing-sui

THE subject of recrystallization and grain growth has been much studied and the literature on this subject is numerous. Such studies have been mostly carried out by metallographic examination of X ray methods. Since recrystallization and grain growth involve elementary atomic processes, their mechanism can best be elucidated by a study of some properties which can be readily traced back in terms of such atomic processes. Prior to a detailed quantitative study, however, it is necessary to explore first the possibility and practicability of utilizing any particular property for obtaining the desired information. We have pointed out in a preceding article' that the internal friction of cold-worked metals is extremely high during recrystallization and it drops abru~tlv once the recrystallization is complete. ~reviois work has also shown that the viscosity of grain boundaries in a recrystallized specimen at a given temperature is raised by grain growth.' It seems thus that the measurements of internal friction may furnish a useful tool for the study of the mechanism of recrystallization and grain growth in terms of elementary atomic processes. The purpose of this paper is to report results of a study along this line. We will demonstrate that the internal friction method does give results in agreement with those furnished by conventional metallographic examinations. Once such a correlation has been established, we will be in a position to take further steps to achieve new information which cannot be achieved by conventional methods. The measurements of internal friction were made using apparatus and procedures similar to those used in the preceding article. All the measurements were made under such a small stress level that the internal friction is independent of stress level. The frequency of vibration is, unless mentioned otherwise, about one cycle per second in all cases. Internal Friction and Recrystallization Complete Recrystallization Temperature: Fig. 1 shows the internal friction curve during annealing of a few metals: aluminum, alpha brass and iron. These curves were determined in the following manner. In the curve for aluminum, internal friction measurements were performed upon. 99.991 aluminum subjected to 95 pct reduction area. The internal friction was first measured at room temperature. The specimen was then annealed at 50°C

Jan 1, 1951

By R. S. Wagner, H. Brown

Criteria for nucleation with the aid of twin planes during crystal growth from the melt are discussed. It is shown experimentally that bismuth crystals can grow from a subercooled melt in a twinned bismdtic form. A mechanism of growth based on the presence of at least me twin plane is proposed. It is well known that faceted growth can be observed in crystals grown from the vapor phase, dilute solutions, or from the melt. Faceted growth, in which the crystal is bounded by its slowest growing faces, will occur if the growth rate is strongly orientation dependent. The addition of atom layers on a facet plane can only occur by two-dimensional surface nucleation or with the aid of an imperfection. Nucleation with the aid of dislocations was proposed by rank' and observed to be of particular importance in crystal growth from the vapor phase. Nucleation with the aid of two-dimensional imperfections, notably twin planes, was suggested by stranski2,3 and Frank.4 A twin plane, terminating at the growth interface, can form a reentrant step at which nucleation can occur at a much smaller super-saturation (or supercooling) than required for two-dimensional surface nucleation. Nucleation by a twin plane usually results in a fast growth rate along a crystallographic direction parallel to the twin plane. Such a nucleation mechanism, based on the presence of a twin plane, has been used by Dawson5 to explain the growth and morphology of sheet-like crystals of paraffin n-hectane. In recent years more evidence was found that nucleation by twin planes occurs frequently in crystal growth from the vapor phase and from dilute solutions, for example, in cadmium,' barium titanate,7 silver,8 silicon9 and gallium arsenide.10 In crystal growth from a supercooled melt, however, nucleation by twin planes has so far only been observed in materials with the diamond or zinc blende structure. Bennett and Longini11 were the first to recognize the important role a single twin plane plays in the growth of germanium dendrites. Subsequently, it was found that a prerequisite for continued propagation of germanium dendrites is the presence of two parallel twin planes which form a self-perpetuating system of nucleation sites.12 Sili- con and some III-V compounds such as InSb also grow dendritically by twin plane nucleation. It appears that the following criteria must be satisfied in order that nucleation with the aid of twin planes can occur: A) The growth form of the material must be faceted." B) The formation of twin boundaries, by a fault in layer sequence during growth, by plastic deformation, or by an accidental meeting of properly oriented crystals, must be possible. C) Twinning must form a reentrant step where the twin boundary terminates at the faceted growth interface. D) These three conditions are necessary, but in certain cases not sufficient for continued crystal growth with the aid of a twin plane. Depending on interface morphology, a combination of more twin planes is sometimes required to form a self-perpetuating system of nucleation sites. This investigation was carried out with the idea in mind that nucleation with the aid of twin planes is a more general phenomenon and should occur in those materials, grown from a supercooled melt, which satisfy the criteria outlined above. It has been found that crystals of high-purity bismuth grown from a supercooled melt can grow by the aid of a twin plane. In the first two sections the faceted growth form and the twinning elements of bismuth are discussed. In the last section prismatic crystals of bismuth, which appear to grow with the aid of a deformation twin are discussed.

Jan 1, 1962

By J. C. Wilhoit, J. B. Cheatham

Although an oil well is a long cylindrical hole with an irregular bottom, it appears likely that the nature of the stress concentration at the bottom of the hole can be ascertained from an analysis of the stresses around a short cylindrical cavity with rounded comers and smooth bottom. Such a cavity is studied primarily because it leads more readily to a solution to the problem by the use of stress functions. In this paper the stress distribution around a short cylindrical cavity subjected to bit loading, overburden and drilling-fluid pressures is determined by means of an analytical solution which approximately satisfies the boundary conditions of the problem. From this solution the stresses at the corner of the hole are calculated to be about 35 per cent lower than comparable results obtained by photoelastic and relaxation analyses. This difference is apparently due to the large radius of curvature at the corner of the cavity in the present analysis. Since good agreement is obtained between the results of this analysis and the stresses calculated for a similar loading on a semi-infinite elastic solid, it is concluded that the bit action in the region near the center of the hole is not appreciably affected by the presence of the sides of the hole. INTRODUCTION Much has been written concerning drilling "under down-hole conditions" and pertaining to the stress distribution in the rock at the bottom of an oil well.1-5 For example, it is known that identical rocks can be drilled more rapidly at the surface than under subsurface conditions of pressure and stress.6 Information on the behavior of rocks under loading can be obtained from triaxial test data.7-9 From such tests it is found that rocks exhibit brittle failure when the confining pressure and pore pressure are equal, but the mode of failure may change to ductile as the difference between the confining pressure and the pore pressure is increased. Brittle failure implies that there is very little permanent deformation before fracture, whereas ductile failure indicates that permanent deformation takes place before fracture. Some rocks are ductile at differential pressures of 5,000 psi , but other rocks are brittle even at differential pressures of more than 50,000 psi. Cuttings embedded in mud at the bottom of the hole may act as a plastic mass which the bit teeth must penetrate in order to attack the virgin rock below. 10 During drilling, the mud pressure acts as the confing pressure, and in many cases the difference between the mud pressure and the formation pore pressure IS sufficiently low so that the rock most likely falls in a brittle manner. Very little penetratiori by the bit teeth may be required for brittle failure of the rock. For these brittle materials, the elastic stress distribution is of practical interest in determicing the possible effects of a given loading on failure. The penetration of bit teeth into ductile or plastic rock has been analyzed previously ll,12 and will not be considered further in the present work. During actual drilling, many teeth act at various points ovel an irregular hole bottom. In the present analysis a solution is obtained for an idealized problem of determining the elastic stress distribution caused by only one tooth acting alone at the center of a smooth hole bottom. It obviously is not proposed that any driller should put a special one-tooth bit on bottom, but it is hoped that extensions of the simpler problems can eventually lead to a better understanding of more complex actual drilling phenomena. To obtain a solution by the use of stress functions, a short cylindrical cavity with rounded corners and smooth bottom is studied. The solution to this problem should give an insight into the nature of the stress concentration at the bottom of an oil well which is in reality a long cylindrical hole with an irregularr bottom. After selection of the proper curvilinear co-ordinate system, the stress functions are expressed as series of Legendre polynomials. The coefficient of each term in the series is then determined to satisfy the boundary conditions at a finite number of discrete points on the boundary of the cavity with least square error. Results are compared with bottom-hole stresses obtained by photoelastic and relaxation analyses.

By B. K. Larkin

Solutions to the diffusion equation for a line source located anywhere in a region bounded by a circular discontinuity are presented. Such solutions follow automatically from the Green&apos;s function presented by Jaeger.4 Petroleum industry applications of this problem would include transient compressible fluid flow in porous media bounded by a discontinuity. Since several recent papers have treated the subject in less general form, it would appear that many workers in this area of the petroleum industry are not aware of Jaeger&apos;s work. STATEMENT OF THE PROBLEM In several trearments1,2,3 of the transient flow of compressible fluids in porous media it was convenient to consider a region to be bounded by a circular discontinuity. In such a region (Fig. I), the properties in Region 1, r < a, are constant but different from the properties in Region 2, r > a. Hurst, l using the Laplace transform, obtained solutions for a line source located in the center of such a porous medium. The purpose of this work is to point out that a much earlier paper by Jaeger4 presents the solution for a line source located anywhere inside the discontinuity. The assumption is made that a line source may be used to approximate a well. In the following material it is convenient to use the terms source and well as being equivalent; however, the reader should remember the distinction in applications. SOLUTIONS Jaeger presented the Green&apos;s function for a line source, or well, in the composite region shown in Fig. 1. In the most general form, the solution for a system of j wells in Region 1, each producing at a time varying rate, qi (t), is

By H. H. Uhlig

Soon after general use of stainless steels began, it was observed in practice that certain combinations of factors tended to induce corrosion by pitting. For most applications this was a serious drawback, not SO much because the structural properties of the metal were impaired but because of the rapidity with which heavy sections of the alloys were penetrated by small elongated pits. These pits seemed to initiate readily in oxidizing metal salt solutions like ferric chloride and in chloride solutions like sea water. It was observed that in sea water pitting was more frequent in stagnant or polluted waters than in highly aerated, moving waters. The steels in these chloride solutions were observed to be sensitive to long contact with material such as sand grains or attached barnacles. At points of attachment or contact it was not uncommon to discover initiation of corrosion. Pits once begun at contact faces were observed to grow rapidly, usually elongating phenomenally in the direction of gravity until the metal was perforated. Hydrochloric acid and other nonoxidizing acids, on the other hand, were observed to corrode stainless steels generally; the weight losses often were higher, but the penetration less than for the pitting type of corrosion. The causes of pitting, a type of corrosion recognized as characteristic not only of stainless steels but of many additional metals and alloys, are important in corrosion studies. A possible explanation bears practical significance, for once it is known why pits begin where they do and continue to grow after initiation, intelligent direction can be given to diminishing corrosion. This can be done either by some alteration in the composition and treatment or&apos; the alloy or by some alteration in the environment. It appears foremost in importance to discover the nature of pit foci, for if initiation of pits can be discouraged their growth will be no longer a factor to be considered. In a multi-component alloy containing many impurities normal to production of such an alloy, each of which may play a part in pitting, and whose corrosion resistance is sensitive to heat-

Jan 1, 1940

By H. H. Uhlig

Soon after general use of stainless steels began, it was observed in practice that certain combinations of factors tended to induce corrosion by pitting. For most applications this was a serious drawback, not SO much because the structural properties of the metal were impaired but because of the rapidity with which heavy sections of the alloys were penetrated by small elongated pits. These pits seemed to initiate readily in oxidizing metal salt solutions like ferric chloride and in chloride solutions like sea water. It was observed that in sea water pitting was more frequent in stagnant or polluted waters than in highly aerated, moving waters. The steels in these chloride solutions were observed to be sensitive to long contact with material such as sand grains or attached barnacles. At points of attachment or contact it was not uncommon to discover initiation of corrosion. Pits once begun at contact faces were observed to grow rapidly, usually elongating phenomenally in the direction of gravity until the metal was perforated. Hydrochloric acid and other nonoxidizing acids, on the other hand, were observed to corrode stainless steels generally; the weight losses often were higher, but the penetration less than for the pitting type of corrosion. The causes of pitting, a type of corrosion recognized as characteristic not only of stainless steels but of many additional metals and alloys, are important in corrosion studies. A possible explanation bears practical significance, for once it is known why pits begin where they do and continue to grow after initiation, intelligent direction can be given to diminishing corrosion. This can be done either by some alteration in the composition and treatment or&apos; the alloy or by some alteration in the environment. It appears foremost in importance to discover the nature of pit foci, for if initiation of pits can be discouraged their growth will be no longer a factor to be considered. In a multi-component alloy containing many impurities normal to production of such an alloy, each of which may play a part in pitting, and whose corrosion resistance is sensitive to heat-

Jan 1, 1940

By A. F. Meston

Centrifugal force has been used for centuries for separating liquids but machines for doing this are a comparatively recent development. The use of these machines is being extended into many industries but this paper is confined to their use in the oil industry. The centrifugal machine is found at the well where "cut oil" is dehydrated for acceptance by pipe lines; and in the refinery and byproduct plant. In fact, wherever finely divided suspended particles should be removed from an oil, there is a possible use for a centrifugal machine, if the particles have, or can be made to have, a specific gravity different from that of the oil. Centrifugal machines are also used for cleaning fuel and lubricating oils and dehydrating transformer oils. Applications and Results When oil comes from the well mixed with water, it is spoken of as cut oil. Settling often does not remove sufficient water for the oil to be accepted by pipe lines, thus necessitating chemical or other treatment. Centrifuging alone, or following chemical treatment, effectively prepares such oil for pipe lines, as is shown by the following data: WateR, Etc. Wat~R. Etc. Temperature, Oil to Pipe Line, aT StUt at Finish Degrees F. Bel. Per HouR PIE Cent. PEECent Oklahoma lease.... 160 10 10 0.25 Kansas lease....... 125 4 20 0.25 to 2 On the Oklahoma lease, the machine was cleaned of solid material once in 12 hr. At first, it was thought that chemical treatment was necessary to start separation and 1 qt. of prepared compound was added to each 100 bbl. of the cut oil before centrifuging. Later it was found that

Jan 1, 1924

By S. Lipson, H. W. Antes, H. Rosenthal

A study was made of the effect of ingot structure on the strength and ductility of high-strength wrought-aluminum alloys. It was found that a fine-cast structure facilitated complete homogenization which, in turn, resulted in significant increases in ductility and strength. A completely homogenized 7075-T6 alloy developed tensile properties of 85,000 psi UTS, 75,000 psi YS, with 40 pct RA. Completely homogenized 7001-T6 alloy tensile properties were 102,000 psi UTS, 99,000 psi YS, with 19 pct Ra. A method was devised for making small ingots having secondary dendrite arm spacing of less than 10 u. This method involved multiple-pass arc melting of commercial rolled plate with a tungsten electvode. This material could be completely homogenized after 3 hr at 900°F; homogenization of the original plate material was not complete after 120 hv at 900°F. Degree of homogeneity was determined by use of metallographic and electron-microprobe analyses. The electron-micro-probe study also showed the preferential segregation of solutes in the microstructure. HIGH-strength aluminum alloys, such as those of the 7000 series, usually freeze by the formation and growth of dendrites. The dendrite arm spacing (DAS) depends on the rate of solidification.&apos; Commercial ingots are usually direct chill-cast to promote more rapid solidification, but, due to the large mass of the ingot, localized solidification times are long and a large DAS results. During solidification, solute elements are rejected by the solid as it forms, causing enrichment of the liquid and ultimately solute-rich interdendritic regions. In order to attain a homogeneous ingot, the segregated solutes must diffuse across the dendrite arms. The larger the DM, the longer the time for complete homogenization. In the case of commercial ingots, the DAS is so large that the time for complete homogenization is prohibitively long and, therefore, second phases or compounds are always present. These un-dissolved phases are carried over to the wrought material during processing, resulting in an impairment of strength and ductility. In addition, the mechanical fibering of the undissolved second phases or compounds during working results in mechanical property anisotropy. If complete homogenization could be attained, higher ductility could be expected. The realization of higher ductility at current strength levels is a desirable objective; however, if higher-strength alloys were wanted, it might be possible to sacrifice some of this ductility by adding more solute elements and produce even higher-strength alloys than are currently available. Further, if complete homogenization leads to more efficient utilization of solute elements, then more dilute alloys should have relatively high strengths with very high ductility. In all instances, it would be expected that the degree of mechanical property anisotropy due to mechanical fibering would be reduced. Therefore, it was the purpose of this investigation to produce cast structures that would facilitate homogenization and to determine the effect of homogenization on the properties of high-strength, wrought-aluminum alloys. MATERIAL CLASSIFICATION Commercial Alloys. In order to illustrate the non-homogeneous condition that exists in commercial high-strength, wrought-aluminum alloys, typical micro-structures of 7001, 7075, and 7178 are shown in Fig. 1. The chemical compositional specifications of these alloys are given in Table I. It can be seen in Fig. 1 that a considerable amount of undissolved second-phase material is present in each of these alloys. The solute elements associated with the undissolved phases were identified by electron microanalyses. Back-scattered electron images and characteristic X-ray images of the three commercial alloys are shown in Figs. 2, 3, and 4. These data indicate that the second phases are regions of high copper and high iron-copper concentrations. The second-phase material also was analyzed for magnesium, zinc, manganese, chromium, and silicon, but no significant enrichment above that of the matrix was found. Therefore, the problem of homogenization resolved itself into one of dissolving the copper-rich and the iron-copper-rich second phases. In order to accomplish this objective, two approaches were made. The first was to reduce the iron as low as possible since this element has a maximum solid solubility of 0.03 pct in aluminum. The second was to produce cast structures with finer DAS to facilitate dissolving the second phases. Commercially Produced High-Purity Alloys. A special high-purity, 2000-lb ingot of 7075 alloy was made by a commercial producer. This alloy contained the following weight percentages of solutes: 5.63 Zn, 2.48 Mg, 1.49 Cu, and 0.21 Cr. All other elements combined were less than 0.02 pct by wt including iron and silicon at less than 0.01 pct each. The ingot was cast and processed into rolled plate using standard commercial techniques. Microstructures of standard commercial 7075 and the special high-purity 7075 are shown in Fig. 5. It can be seen from this figure that the high-purity alloy has less undissolved second-phase material, but a significant amount was still present. The second phase in the high-purity material did not contain iron but it was found to be enriched with copper. The slight effects of the increased purity and de-

Jan 1, 1968

By J. B. Newkirk

ABOUT twenty-seven years ago W. bergl discovered that interesting detail could be seen in an X-ray diffraction spot made with a rock-salt crystal if the recording photographic film were held very close to the reflecting crystal. He also showed that much of this detail could be explained in terms of the deformation structure of the specimen. In the same year, 1931, Fox and parr2 reported that X-ray reflections from a quartz crystal were much more intense while the crystal was undergoing piezoelectric oscillation than when it was at rest. This observation was soon confirmed (and explained in terms of X-ray extinction) by Barrett3 in the United States and by Nishikawa et a1.,4 in Japan. During the next few years Barrett refined Berg&apos;s method for making X-ray diffraction micrographs and applied it to the study of metallic crystals. He reported this work in the 1945 annual lecture of the AIME.5 Since 1945 relatively little use has been made of the Berg-Barrett (B-B) method for making diffraction micrographs, though considerable interest in investigating subcrystal structures by other methods has developed. Some of these methods depend upon evaporation6 or chemical etching7 and, therefore, suffer from the occasional intrusion of subtle artifacts such as those recently reported by Hooker for leada and Welsh for aluminum.9 Other methods require the introduction of foreign elements which "decorate" the substructure in some way, thereby rendering it detectable by direct" or indirect1&apos;. visual examination. Still others depend upon complex and often highly questionable analyses of X-ray diffraction line profiles. There have also been a number of related X-ray techniques, such as the Lambot,12 Schulz13 and Merlini and Guinier,14 which have proved to be quite useful for specific applications. Some of these methods give a picture of the substructure which is more or less directly related to the shape and the topography of the specimen. The Berg-Barrett method carries this desirable feature to the limit. Closely related to the B-B method are three photographic X-ray techniques recently described by Lang.15 These methods give beautiful pictures of the internal structure of crystals but are limited by the facts that the required apparatus is rather complex, exposure times are long, and the specimen crystals must be thin. An experimental appraisal which I have recently made of the original B-B method has shown that this simple technique is not only inexpensive and convenient, but can give more information than was apparently realized by its inventors. For example, first-order subgrains in iron-silicon crystals were clearly delineated and their relative orientation subject to description. Also defect structures could be seen within the subgrains and in some materials slip bands could be clearly seen with respect to the topography of the rest of the specimen. This much had already been described by Barrett. However, in the present study it was found that the actual sites of individual dislocations which emerge upon the crystal surface could be located. Furthermore, by a simple procedure, the direction (but not sign) of the dislocation Burgers&apos; vector could be defined as well.

Jan 1, 1960

By A. Szirmae, Hsun Hu

The early stages of recrystallization in a 70 pct cold-rolled Si-Fe crystal of the (110) (0011) orientation were studied with a Siemens electron microscope. Orientation studies based on electron-diffractzotz. patterns confirm the results of previous texture analysis. The driving energy for recrystallizatior and the critical radius for growth were calculated from the dislocation energy and the energy of the subgrain bourzdaries, and it was found consistent with the observed size of the recrystallized grains. The recrystallization characteristics of crystals with different initial orientations are discussed. The recrystallization of cold-rolled (110)[001] crystals of Si-Fe has been widely studied by various investigators.1-4 Their results on both deformation and annealing textures are in good agreement. The rolling texture after 70 pct reduction consists mainly of two crystallographically equivalent (111) [112] type textures and a minor component of the (100) [011] type. The latter is derived from the deformation twins, or Neumann bands, which are formed during the early stages of deformation and later rotate to the (100) [011] orientation upon further rolling reduction. Between the two main (111) [112] type textures, there is some orientation spread, because of which very low intensity areas appear in the pole figure. If these very low intensity areas are considered to be a very weak component in the texture, then a (110) [ 001 ] orientation may be assigned to them. When this rolled crystal is annealed at a sufficiently high temperature for recrystallization, the texture returns to a simple (110) [001]. The purpose of the present investigation was primarily to seek a better understanding of the recrystallization process by using the electron transmission technique. The (110) [0011 type of crystal was selected because orientation data for it are well known from previous studies with conventional techniques. Direct observations on the recrystallization of such a crystal have also been made by using a hot-stage inside the electron microscope, and the results will be reported in another paper. MATERIAL AND METHOD A single-crystal strip of the (110) [001] orientation was prepared from a commercial grade 3 pct Si-Fe alloy by the strain-anneal technique.= The strip was approximately 0.014 in. thick, and was rolled 70 pct at room temperature to a thickness of 0.004 in. Specimens were cut from the rolled strip and were annealed in a purified hydrogen or argon atmosphere. They were then electrolytically polished in a chromic-acetic acid solution to very thin foils. Best results were found by polishing first between two narrowly spaced flat cathodes with the specimen edges coated with acid-resisting paint, followed by polishing between two pointed electrodes until a hole appeared in the center as described by Bollmann.6 It was found that a thin transparent film always formed along the thin edges of the polished specimen. This film was then removed by rinsing the specimen very briefly in a solution of alcohol with a few drops of HF or HCl. RESULTS AND DISCUSSION 1) The Deformed Crystal. From the electron-diffraction patterns taken at various areas of an as-rolled specimen, the texture components as deduced - from ordinary pole-figure analysis were confirmed. Over most of the areas where orientation was examined, a (111) pattern with a [112] direction parallel to the rolling direction was obtained. This corresponds to the main deformation texture of the (111) [112] type. In a few areas the diffraction pattern was (100) [Oil], corresponding to the minor-texture component derived from the Neumann bands. The (110) [001] orientation, which corresponds to the very weak intensity area in the pole figure, was found infrequently. A typical example of the deformed matrix having the (111) type main texture is shown in Fig. 1, where (a) is the microstructure and (b) is the diffraction pattern taken from that area. It was also frequently observed that in other areas more or less continuous rings of weaker intensity were superimposed on the simple (111) diffraction pattern, suggesting the presence of a wide range of additional orientations. Other evidence indicated that the recrystallization characteristics are different in these two different types of areas. The hot-stage observations which provide this evidence will be discussed in another paper. AS shown in Fig. l(a), numerous dislocation-free areas of very small size are embedded in the "clouds" of high-dislocation density. This indicates that the deformation of a single crystal, even after a rolling reduction of 70 pct, is far from uniform on a micro-

Jan 1, 1962

J. D. Fast and J. L. Meijering (Philips Research Laboratories, N. V. Philips&apos; Gloeilampenfabrieken, Eindhoven, Netherlands)— After the departure of our friend Dijkstra to the United States, investigations on the effect of alloying elements on the behavior of nitrogen in a iron were continued in Eindhoven. We too found internal friction curves with two separate peaks for iron containing nitrogen in addition to 0.5 atomic pct V or 0.5 atomic pct Mo. Our first publication on these investigations" appeared almost simultaneously with the paper now under discussion. At first sight our experimental results seem to be in harmony with their conclusions, but a closer examination reveals that in the case of the Fe-V-N alloy the abnormal peak is not controlled by one time of relaxation only. Whereas iron containing 0.5 atomic pct Mn or Mo absorbs an amount of nitrogen of about the same magnitude as that absorbed by pure iron under identical conditions, iron containing vanadium absorbs in addition one nitrogen atom for every vanadium atom. This last amount, far exceeding the first amount in the case under consideration, combines chemically with the vanadium and causes no internal friction. The "free" nitrogen in the vanadium alloy gives rise not only to a damping peak corresponding to that in pure iron but— due to the presence of VN particles in the metal—also to the abnormal peak at higher temperatures. The VN particles create interstitial sites around themselves where the free nitrogen atoms are bound much tighter than in the normal interstices. These abnormal interstices, therefore, will capture free nitrogen atoms rapidly, whereupon these give rise to the abnormal damping. The binding energy in the abnormal interstices is not the same for all, and with coarsening of the VN precipitate the distribution of these energies is displaced toward the side of stronger binding. This is deduced from a shift of the summit of the second peak toward higher temperatures (from 80" to 88°C in our experiments) caused by prolonged heating at 950°C. From the intermediate state where they cause the abnormal damping, the nitrogen atoms pass over rather rapidly into the fully precipitated state (iron

Jan 1, 1954

By F. Hass, N. W. Lord

This paper gives the results of experiments conducted in the metallurgical laboratory of the Ohio State University with the objects of determining: First, the calorific powers of a number of coals in general use in Ohio; and second, how far ordinary analytical methods could be used as a basis for computing these values. Incidentally a test of the performance of the calorimeter was involved. The chemical work has been carried on in the department for some time, so that the whole investigation has extended over three or four years. The Mahler calorimeter was purchased from L. Golaz in Paris, and is practically identical with the one described and figured by Mahler in his monograph "Contribution a l&apos;Etude des Combustibles," from the Bulletin de la Société d&apos; Encouragement pour l&apos;lndustrie Nationale. A figure and description is also given by William Kent in The Mineral Industry for 1892, page 97. There were furnished with the instrument three thermometers covering a range of from 7°.5 C. to 31° C. Thermometer "A" (17°.5 to 31°) was carefully calibrated by reading the ends of a thread of mercury in sixteen positions covering the whole scale, supplementing this by readings of longer threads and deducing the errors of scale by the method published by Prof. Holman in the Technology Quarterly of September, 1887. The maximum error of a single reading was found to be 0°.0042 C. Thermometer "B" (13° to 25°) was compared directly with " A " over the scale common to both, and a variation was found of 0°.0145 C. for 7°.5 (or 0°.002 for l°) of the scale. Thermometer " C" (&apos;7°.5 to 19°.0) was omitted from the cornparison, as it was rarely used, being only required where measurements were made at low temperatures. From the

Jan 1, 1898

By C. S. Corbett

There is much comment at present in the ranks of the oil industry regarding unit operation of oil fields and the benefit that would accrue if it could be extensively applied. It seems certain that, as an immediate corrective of the present situation, overproduction could be effectively curtailed with all the advantages of proper conservation of petroleum resources and with no important loss to anyone connected with the industry. Unit Operation in Certain Foreign Fields Many an oil operator in America would doubtless like to have exclusive control of one or more oil-bearing structures for development in accordance with the economic position of the industry and especially in accordance with the best production practice known. A few operators now have this privilege, particularly in certain foreign fields, and are following lines of procedure which show that they are aware of the great opportunity that is theirs. We find in an article by Professor Strigeoff,1 and in a paper read by Captain Comins2 before the American Petroleum Institute, the outlines of procedure adopted, respectively, by the Soviet Government for the nationalized Russian oil fields and by the Anglo-Persian Oil Co. for its fields in Persia. Comprehensive plans for the unit operation of other oil fields may have been described publicly but no such descriptions have come to the attention of the writer. New fields are coming more and more into the hands of single operators or of a few who control large activities and who appreciate fully the need for cooperative action and are willing to forego the lure of a large quick profit from high flush production in order to secure the advantage of better stabilization in the industry and a larger though more deferred profit by operating the field as a unit. Much can be done toward efficient development of an oil field controlled by a few operators who are willing to cooperate for that purpose, but the best result can be obtained only by pooling their interests in the field

Jan 1, 1930

By R. D. Pehlke, W. M. Small

The effect of added alloying elements on the solubility of nitrogen in a liquid alloy of 74 wt pct Fe. 18 wt pct Cr, and 8 wt pct Ni has been studied. At 1600°C and 1 atm nitrogen pressure, aluminum, chromium, columbium, manganese, molybdenum, tantalum, and vanadium increase the solubility of nitrogen in the liquid 18 Cr-8 Ni alloy, whereas additions of cobalt, copper, nickel, silicon, tin, and tungsten decrease the solubility. Interaction parameters based on a constant ratio of iron, chromium , and nickel have been used to quantitatively define the changes in nitrogen solubility. INVESTIGATIONS on the solubility of nitrogen in liquid iron have usually treated the pure metal, and often the influence of a single added element. Pehlke and Elliott1 carried out a comprehensive study on the influence of alloying elements on nitrogen solubility in liquid iron, and compared their results with previous studies. Turnock and pehlke2 have recently reported a study on the solubility of nitrogen in multicomponent liquid iron alloys. The original interaction parameter proposed by wagner3 was successfully employed in these studies. The need for obtaining information on the gas solubility in more complex alloys is indicated by the increasingly significant role played by dissolved gases in the processing of iron-based materials. The commercial stainless steels, for example, represent an area where data on nitrogen solubilities are required as a function of composition, temperature, and gas pressure. The nitrogen solubility in liquid Fe-Cr-Ni alloys has been studied by Humbert and Elliott.4 Their investigation covered the entire ternary system, and attempted to use data from binary alloys to predict nitrogen contents in liquid ternary alloys. Langenberg,5 using a method developed by Morris and buehl,6 calculated the nitrogen solubilities in multicomponent iron alloys from data available on binary iron alloys at 1600°C. Nelson,7 using a regular-solution model, extended this prediction to include the effect of temperature. Chipman and corrigan8 and Turnock and pehlke2 also employed empirical methods to calculate nitrogen solubilities in liquid multicomponent iron alloys. In order to provide a basis for predicting nitrogen solubility in liquid stainless steels, and to extend the data available for thermochemically modeling systems of this type, the following investigation was carried out. The study involved measupements of nitrogen solubility in a nondilute alloy and examination of the influence of a small addition of an alloying element on the nitrogen solubility. The study was focused on a very narrow range Of composition in the vicinity of 18 wt pct Cr-8 wt pct Ni (herein referred to as 18-8) with special emphasis on the change of.nitrogen solubility with the addition of a fourth metallic element. EXPERIMENTAL PROCEDURE A Sieverts&apos; apparatus, described previously,1,2 was used in this investigation. The charge materials were contained in a recrystallized alumina crucible and inductively melted. Additions were dropped from a glass side-arm. All materials were hydrogen-refined and vacuum-treated to eliminate or minimize the oxygen content. The source and purity of materials is given in Table I. The initial metallic charge was heated to approximately 1000°C and held under vacuum for 30 to 45 min as a means for removing hydrogen and adsorbed gases. Argon was used as the calibrating gas to determine the "hot volume". The average hot volume of the system was approximately 50 cu cm STP and a few experimental runs were made using a reaction bulb with a hot volume of 80 cu cm. The temperature range studied was from 1550° to 1700°C and the temperature was measured optically. THEORETICAL PRINCIPLES General Discussion. Nitrogen dissolves in liquid iron alloys according to the reaction: 1/2N2(g) = N (wt pct in solution) [l] The equilibrium constant, K1, for this reaction is written as:

Jan 1, 1969

By W. R. Ingalls

In reviewing the history of the metallurgy of zinc, I shall pass hastily over what is only of antiquarian interest. That has been excellently treated by Dr. Bernhard Neumann in "Die Metalle" (1904) and has been described briefly in my "Production and Properties of Zinc" (1902), in my "Lead and Zinc in the United States " (1908), and in other metallurgical works of more or less the same date. In this present monograph, I have it in mind to confine myself mainly to technical practice, especially to that of the last 75 years, prior to which period advance was slow and of no great moment. The ancients made brass by the cementation process, i.e., embedding copper in a mixture of calamine and carbon and heating, whereby zinc oxide was reduced and zinc was vaporized and combined with the copper. Zinc was isolated by some of the alchemists, who named it and knew something of its properties, but made no use of it. Long before then, however, zinc was produced in India. Later it was produced in southern China. Possibly the Chinese obtained their knowledge from India. The Chinese in remote places still produce small quantities of zinc. I have seen photographs of their furnaces; or pots, for they hardly deserve the dignity of being called furnaces. I imagine that they are the same that were used centuries ago, for I cannot conceive of anything more primitive. Anyway, it is certain that the idea of a commercial production of zinc in Europe was imported from the Orient, where the metal was known in commerce as Speauter and Spiauter, whence speltrum and finally our term spelter. Tutanego and Tuteneague are other old names. Dr. Isaac Lawson went to China about 1730, expressly to discover the method of its production. What connection there was between Isaac Lawson and John Champion we do not know, but the latter obtained in 1739 a patent for a process of distillation downward and at some time between 1740 and 1743 erected a works at Bristol and actually began the manufacture of spelter. A production of 200 tons per annum is mentioned. In about the year 1766, Rishop Watson visited the Champion works and saw the process in operation, which previously had been

Jan 1, 1937

By R. Wachtell

IN order to study better the phenomena at work in various phases of diffusion of the Fe/Si system when compounded and alloyed by powder metallurgy methods, several attacks have been planned. Electrical, hardness and other measurements have been discussed e1sewhere.l,2 The metallographic phenomena will be considered here. Concerning the metallography of the ferrosilicon alloys, some initial discussion is in order. As this laboratory discovered to its chagrin, there are many traps that lie in wait for even the experienced metal-lographer when he deals with alloys of high silicon content. Chief of these is probably the anomalous behavior of these materials under conventional etching techniques. We have before us, for instance, Corson&apos;s paper" of 1928, wherein is mentioned and illustrated (probably for the first time) the peculiar "barley shell" structure sometimes found in these alloys. Again in 19412 he same author reports the structure in 5-14 pct silicon irons. Houghton and Becker mention its presence&apos; but make only tentative effort to explain it. In 1943, Hurst and Riley6 discussed the "barley shell" and declared it to be a false structure, resulting from the peculiar and characteristic film-forming propensities of the alloy. At about the same time, Wrazej7 proved correct the contentions of Hurst and Riley, establishing pretty well the mechanisms of formation and identifying the constituents involved. Hurst and Riley6 a1so describe in their paper (1943) a "cracked film" structure, also a pseudo-morph, the precise nature of which they do not suggest. Careful examination of such a film reveals that it not only cracks but begins to curl away from the surface of the metal and peel, much in the manner of flaking paint. The careful microscopist will be able to focus on the topmost edge of the flake, and, by optical sectioning, follow it down to the metal surface. We have been able, by oblique illumination of such specimens, to observe the raised segment of the film, the shadow that it casts, and the mating segment on the metal into which it fits. As late as 1946, Hurst and Riley8 found occasion to correct misinterpretation of this "cracked film" structure in a work by others on a 12 pct Si/Fe alloy. The "barley shell" and "cracked film" pseudo-morphs are not the only ones encountered in studies of these materials. A third pseudomorph, which may, however, have some structural significance is a fine striation of the surface. Closely spaced and parallel striae extend entirely across single grains. Each grain shows a different direction for the striae, and different closeness of the spacing. The regularity of this structure, and the fact that the striae do not cross from one grain to another, suggest that the structure is a film cracking controlled in some way by the crystal plane orientation of the surface being etched. In general it is wise for the metallographer dealing with these alloys to cultivate a feeling of uncertainty not only of the more complex questions of interpretation, but also of the basic question of whether that which he sees is indeed a true representation of the structure. We have taken, as a first test of the validity of a structure, its reproducibility "in situ" after repolishing and re-etching of the samples. Thus we knew the "barley shell" to be false (fig. 1) even before encountering the definitive works on the subject. The Metallography of Silicon Diffusion in Laminate Bars: As a first step in the study of the metallography of the diffusion process, we have pressed a series of laminate bars. These bars, or "sandwiches" as we have termed them, were pressed with covering layers of iron powder, and a "filler" of the Fe/Si master alloy under study. Bar dimensions were approximately %, x 3 x 1/4 in. The total

Jan 1, 1951

I do not think too much emphasis can be placed upon creation of favorable climate for development of foreign mineral resources to feed the hungry maw of our industrialized nation. We have become dependent, not only upon the ten raw products indicated in Mr. Bancroft&apos;s article, but upon 71 mineral substances listed by DMPA as in short supply. Forty-four of these are metals, 9 are chemical minerals and 18 are nonmetallic minerals. Of this list only 8 are produced in any large quantity in the United States, and all are vital in peace-time industry. Even more, they are absolutely essential for defense. This represents our present needs. But if our consumption and requirements are projected over the next 25 years as is done by the President&apos;s Materials Policy Commission-The Paley Report-our future outlook becomes appalling. The divergence of consumption over production, even allowing for substitution and conservation, will widen in the future. This means our dependence upon foreign raw materials, mainly minerals, will grow. What are the chief foreign sources of minerals for our future needs? They are chiefly Latin America and the dominions and colonies of the Western European nations. The British Commonwealth countries contain in abundance those minerals which the U. S. lacks. Of 32 of the most critical minerals the Commonwealth is deficient in 7 and lacks only 1; whereas the U. S. is deficient in 18. Strikingly, our deficient minerals are abundant in the Commonwealth and several of their deficiencies are in excess in the U. S. Resources of the two nations complement each other. If Europe should be overrun by an unfriendly power that could control the destinies and resources of the European dominions and colonies, our industrial life would be placed in severe jeopardy. Therefore, I heartily endorse Mr. Bancroft&apos;s statements regarding the Point IV program, provided the program is wisely administered and implemented. It is from the underdeveloped countries, as pointed out by Mr. Bancroft, that most of our future mineral supplies will have to come. Many of the underdeveloped source countries are African colonies and dominions of Western European nations. Our present aid to Europe, therefore, is not, as many infer, a purely one-sided affair; it safeguards our future industrial development and security. Development aid directly to the underdeveloped countries through a well administered Point IV program, can do much, I believe, to safeguard our prosperity. I regard it as a wise investment for future U. S. mineral needs. Dr. Alan M. Bateman Department of Geological Sciences Yale University Mr. Howland Bancroft&apos;s article, The Broadening Road to Foreign Investment, appeared on page 666 of the July MINING ENGINEERING.

Jan 1, 1952

Andrew Carnegie, America&apos;s best-known ironmaster and philanthropist, died at his home at Lenox, Mass., Monday, Aug. 11, after a three days&apos; illness. A pioneer in the steel industry, he introduced into this .country the Bessemer process And formed the plans that have resulted in this country&apos;s supremacy in the steel markets of the world. Known throughout the world for his, gifts, he is also known to engineers as the donor of the home of their National Societies and as the founder of the Carnegie Institute of Technology, of Pittsburgh. For many years, also, he was an honorary member of the American Institute of Mining and Metallurgical Engineers, the American Society of Mechanical Engineers, and of the Engineers Club of New York. What he considered the secret, of his success is shown by the epitaph he wrote for himself, "Here lies a man who knew how to enlist in his service better men than himself." He was buried Thursday, Aug. 14, in Sleepy Hollow Cemetery, Tarry-town, N. Y., the funeral services being private, in accordance with his wish.

Jan 9, 1919

By Arthur J. Boynton

In the preparation of this paper the writer has been influenced by the fact that descriptions of various means of cleaning blast-furnace gas have been published and that further descriptive treatment of the subject will probably be less interesting than a statement of conclusions with regard to preferable methods which have been reached by him as a result of experience and observation in this country and also as a result of somewhat detailed investigation of the subject made toward the end of the year 1927 on the Continent of Europe and particularly in Germany. Owing to various circumstances, including a cost of fuel that is extremely high in relation to the wages of labor, the German iron and steel industry has accumulated experience in gas washing which is as yet in part lacking in the United States of America. The paper begins with a statement regarding the economics of the use of blast-furnace gas, then considers the principles and practices employed in its purification. Uses of Blast-furnace Gas For many reasons having to do with the utilization of coke-oven and blast-furnace gases in steel manufacture and with the use of hot metal, the blast furnace is now usually a part of a steel-producing unit, which also includes coke plant and rolling mill. Therefore both blast-furnace and coke-oven gas are usually applicable to any of the iron and steel-making processes, including the generation of power, and their allocation in any given works should be considered as a single problem. The uses to which blast-furnace gas, either alone or mixed with coke-oven gas may be put, include the following: Regenerative Heating of Ail. for the Blast Furnace.—This is the oldest and metallurgically the rnost important of all uses. It is universally performed with unmixed blast-furnace gas and under proper conditions should require not over 23.5 per cent. of the total gas generated for a blast temperature of 1350" F. For Steam-raising Purposes.—This is almost universally done with unmixed blast-furnace gas. From the standpoint of quantity used, it is at the present time the most important application in American steelworks practice.

By John F. Abel

"The most conservative persons I ever met are college undergraduates." Woodrow Wilson said that in 1905. No one is saying anything like it today. Chaos on the campus was a cliche of the sixties. Since 1905, education has expanded in every direction. Many more people are being educated for much longer periods of time. The school-leaving age has risen from 14 years to 20 years, on an average. Many are in school until after their 25th birthday. On the surface this situation appears all to the good. Our technical society needs a massive yearly infusion of semitrained (or educated, if you prefer) new blood. The efficiency of our economy and our standard of living are tied to high individual productivity which can be achieved only with an educated work force. Our democratic institutions are said to be founded on an educated electorate.

Jan 1, 1970