Search Documents

By D. J. Carney, E. C. Rudolphy

Large macroscopic nonmetallic inclusions were related to altered fireclay refractories by chemical and microscopic means. Pouring refractories are discussed as a source of these large inclusions. Nozzles and wells are major contributors. Use of alkali and titania contents as tracers is described. Recommendations are offered to minimize the sources of inclusions from pouring refractories. IN any attempt to improve the cleanliness of plain carbon and alloy steels, consideration must be given not only to the proper deoxidation practice to minimize inclusions, but also to sources of inclusions from pouring refractories. In some cases, the inclusions resulting from deoxidation may be minor in amount, yet a relatively dirty steel may be produced as a result of improper care in the pouring practices for the steel. The number of studies of inclusions resulting from pouring refractories has increased recently and some excellent reports on this subject have already been published.'4 Some of these reports were reviewed briefly in a companion paper by M. P. Fedock.5 Mr. Fedock's contribution is a fine addition to the studies necessary to improve steel cleanliness for the ultimate benefit of all steel producers and consumers. In the interest of constantly improving cleanliness, the authors have been actively engaged for the past two years in experimentation to determine more closely the sources of inclusions in steel. One phase of this work was associated with efforts to define more closely the sources of macroscopic inclusions which have been experienced on occasional heats. The term "macroscopic inclusions" is defined in general as those inclusions which are visible to the naked eye or at low magnifications of the order of less than X25. These inclusions sometimes can be seen in the macro-etch tests of billets and slabs. This report summarizes a few of the field experiments and laboratory studies conducted at the South Works of the United States Steel Corp., which were made regarding nozzles, wells, and ingot scums, as well as inclusions occurring in steel products. The data in the present study, together with the data of Mr. Fedock concerning ladle erosion, should be of value in regard to future studies of inclusions arising from pouring refractories. The knowledge gained as a result of data collected thus far at South Works has been helpful in improving the cleanliness of the products and in pointing the way toward further improvements. Similarity of Large Inclusions to Refractories and Altered Refractories In the routine inspection of billet etch tests, occasional inclusions visible to the naked eye have been observed. These large inclusions most frequently occur near the top of the ingot and near the billet surface. When such material was encountered, careful examinations were made in an attempt to determine the origin of these inclusions. In a relatively few cases, examination revealed that the material was unaltered fireclay refractory of a type similar to that used for hot-top material, with only the surface of the inclusions having an altered appearance under the microscope. However, the great majority of these inclusions were completely altered-refractory material. The term "altered refractory" is defined

Jan 1, 1955

By Basil B. Zavoico

Production of crude oil in the U.S.S.R. during 1940 is estimated at 222,600,000 bbl., as compared with the revised figure for the preceding year of 220,866,000 bbl., an increase of 0.79 per cent, and at least 20 per cent under the planned output. Baku district (Transcaucasus) remained the outstanding producing area, accounting for 72.33 per cent of the country's production, and this relative importance of the Apsheron Peninsula oil fields will probably continue lor many years to come. In the North Caucasus the Grozny-Dagestan area further extended its decline and the current production in this district amounts to only 6.06 Per cent Of the total U.S.S.R. output, as compared with 35.76 Per cent in 1931 The production of the Kuban-Maikop district remained virtually ullchanged from the preceding year, amounting to 7.64 per cent of the country's total. The Caucasian Province, therefore, in I940 produced 86.03 Per cent of the total production of the U.S.S.R. The promising new Permian Basin district, called Ural-Volga, and referred to sometimes as the "Second Baku," increased its production appreciably during 1940 and the output of that area amounted to 8.31 per cent of the country's total, as compared with 6.35 per cent during 1939. Production in the secondary districts of Russia continued unchanged though some new discoveries in the Emba salt-dome basin suggest that the output of that district may show some increase during the coming years. The drilling operations in Russia during 1940 reached a stage of virtual breakdown and the original footage plans were fulfilled only to the extent of around 50 per cent, while exploration drilling schedules were fulfilled only to the extent of about 25 to 35 per cent. This condition was due to the obvious lack of modern drilling rigs, of good drill pipe and of strong casing. Extended breakdowns occurred with deeper drilling, particularly because with few good drilling rigs available speed was being attempted with rotation rates that the inferior drill pipe and bits could not stand. Twistoffs and endless fishing jobs resulted. The difficulties became so serious a handicap to the Soviet oil industry that it was found imperative to order American drilling equipment and pipe in quantity, a policy that was never favored in the U.S.S.R because it requires expenditure of gold or exchange in major volume, and such exchange usually is reserved only to less bulky key items or to orders directly connected with armaments; also, oil-field machinery is very bulky and the prevailing lack of bottoms makes the transport of the indicated equipment a major problem. But little progress was similarly made in other branches of the Soviet oil industry. NO new major pipe-line construction work was undertaken, consequently the railroads continued to be overburdened with traffic that could be much more effectively handled by pipe lines. No new refinery construction of any magnitude was initiated, though several plants that had been in course of construction for several years were completed during 1940 and operation 554

Jan 1, 1941

By Basil B. Zavoico

Production of crude oil in the U.S.S.R. during 1940 is estimated at 222,600,000 bbl., as compared with the revised figure for the preceding year of 220,866,000 bbl., an increase of 0.79 per cent, and at least 20 per cent under the planned output. Baku district (Transcaucasus) remained the outstanding producing area, accounting for 72.33 per cent of the country's production, and this relative importance of the Apsheron Peninsula oil fields will probably continue lor many years to come. In the North Caucasus the Grozny-Dagestan area further extended its decline and the current production in this district amounts to only 6.06 Per cent Of the total U.S.S.R. output, as compared with 35.76 Per cent in 1931 The production of the Kuban-Maikop district remained virtually ullchanged from the preceding year, amounting to 7.64 per cent of the country's total. The Caucasian Province, therefore, in I940 produced 86.03 Per cent of the total production of the U.S.S.R. The promising new Permian Basin district, called Ural-Volga, and referred to sometimes as the "Second Baku," increased its production appreciably during 1940 and the output of that area amounted to 8.31 per cent of the country's total, as compared with 6.35 per cent during 1939. Production in the secondary districts of Russia continued unchanged though some new discoveries in the Emba salt-dome basin suggest that the output of that district may show some increase during the coming years. The drilling operations in Russia during 1940 reached a stage of virtual breakdown and the original footage plans were fulfilled only to the extent of around 50 per cent, while exploration drilling schedules were fulfilled only to the extent of about 25 to 35 per cent. This condition was due to the obvious lack of modern drilling rigs, of good drill pipe and of strong casing. Extended breakdowns occurred with deeper drilling, particularly because with few good drilling rigs available speed was being attempted with rotation rates that the inferior drill pipe and bits could not stand. Twistoffs and endless fishing jobs resulted. The difficulties became so serious a handicap to the Soviet oil industry that it was found imperative to order American drilling equipment and pipe in quantity, a policy that was never favored in the U.S.S.R because it requires expenditure of gold or exchange in major volume, and such exchange usually is reserved only to less bulky key items or to orders directly connected with armaments; also, oil-field machinery is very bulky and the prevailing lack of bottoms makes the transport of the indicated equipment a major problem. But little progress was similarly made in other branches of the Soviet oil industry. NO new major pipe-line construction work was undertaken, consequently the railroads continued to be overburdened with traffic that could be much more effectively handled by pipe lines. No new refinery construction of any magnitude was initiated, though several plants that had been in course of construction for several years were completed during 1940 and operation 554

Jan 1, 1941

By Eugene A. Stephenson

NUMBER of noteworthy events in the petroleum industry may be reported for 1941, of which the most spectacular was doubtless the rise in the daily rate of crude-oil production to a peak of approximately 4,300,000 barrels. This enormous daily rate did not ensue from the furor of flush pools but represented for the most part merely a slight additional daily delivery from many wells that had previously been operated on a more restricted basis, in line with good conservation practice and also from the adroit increase in the number of days per week by the Texas Railroad Commission. Another important fact was the increase in price throughout the Mid-Continent area from the static level of $1.02 for 36°, A.P.I., crude, to $1.17 per barrel. Efforts to elevate the price above this point have met with severe opposition from the O.P.A.. as has also a similar effort by the PennsyIvania Crude Oil Producers' Association, but the vastly increased costs for materials and labor may shortly give the industry the enhanced price which it has long deserved.

Jan 1, 1942

By John D. Sullivan, Edwin J. Rogers, Chester R. Austin

THE problem of making a building unit combining the necessary physical and mechanical properties and good thermal insulation has been foremost in the minds of architects and ceramic and construction engineers for many years. This paper presents the results of studies on thermally expanding shales or clays to produce light-weight cellular products suitable for making building units. An expanded clay block suitable for building purposes should be large enough so that substantial savings may be effected in labor costs in laying the wall. The permeability should be low and it should have sufficiently good "dry-wall" characteristics to permit exposing the exterior surface to the elements, and to permit plastering directly the inside wall surface. The thermal conductivity should be low and the mechanical properties should be adequate. Obviously, a unit possessing satisfactory qualities for constructing an outside wall would be satisfactory for interior walls and for back-up purposes. The results of studies on bloating various shales or clays[t] and the properties of the expanded products are reported. In another paper1 basic factors involved in bloating of clays are discussed. Manufacturers of ceramic products, particularly structural clay, may encounter bloating of the ware during burning, and precautions must be followed to avoid this phenomenon. About 1927 the C. F. Burgess Laboratories, Madison, Wis., while carrying on an investigation for the American Face Brick Research Corporation, conceived the idea of intentionally bloating clay while holding it in a restrained condition, with the hope of producing a unitary cellular mass. Work was carried on until about 1931, when studies were terminated because of business conditions. These studies were continued later by The Western Brick Co., Danville, Ill., which developed a process of "inwardly expansive bloating."2 The major purpose of the latter investigation was to produce back-up tile to compete with concrete blocks made from Haydite or cinder aggregate. Haydite is a light-weight aggregate formed by heating certain clays or shales rapidly in a rotary kiln. While the investigations at the C. F. Burgess Laboratories or at Western Brick Co. were not carried far enough to lead to the commercial production of material for the construction of walls, particularly outside walls, they showed that certain clays could be thermally expanded and that it was possible to produce a material of low permeability with a large percentage of the total voids or cells closed. Commencing in 1939, the Ozark Chemical Co. sponsored a research program at Battelle Memorial Institute for the purpose of determining whether it is technically feasible to make thermally expanded building units, and specifically to get answers to the following questions:

Jan 1, 1942

By Louis E. Toth, Alan W. Searcy

A modification of Le Claire's microscopic model for self-diffusion is developed in a form suitable for prediction of activation energies for diffusion in disordered substitutional solutions as well as in pure metals Bonding is considered as a localized interaction, and the energy of bonding between atoms of different types is taken as the arithmetic mean of the energies in the pure elements. The activation energies for vacancy formation and migration in substitutional alloys are shown to depend on the empirical constants developed for self-diffusion when the equations are adjusted for the mole fractions of the two elements. The differences in activation energies between alloys and pure metals are calculated and compared with the experimental differences. MaNY different correlations have been proposed for use in predicting activation energies for self-diffusion or diffusion in dilute alloys. Usually theories for self-diffusion cannot be applied to alloys nor can theories for dilute alloys be satisfactorily adapted to self-diffusion. We present here a correlation scheme which can approximate activation energies for diffusion, vacancy formation, and atom migration in substitutional-alloy systems of any concentration. The activation energy for self-diffusion QD has been correlated to the melting temperature Tm,1, 2 the sublimation energy L,,l the heat of fusion Lf,3 crystal structure, and valence.4 Working with mechanical parameters Le claire5 proposed that the activation energy for vacancy migration Qm could be related to appropriate shear moduli. He also proposed that the activation energy for vacancy formation 62, is proportional to Ls. THEORY We consider that Le Claire's expression for 4, is satisfactory. But an alternate expression for Qm in terms of the bulk modulus is just as satisfactory from a theoretical point of view for the prediction of the energy of vacancy migration in pure metals and can more easily be used for alloys. In order for Qm to be a minimum, not only the moving atom but also adjacent and nearby atoms must undergo distortions. These distortions are neither isotropic as is implied by a correlation with the bulk modulus nor unidirectional as implied by a correlation with a shear modulus, but are complex and multidirectional. A complete analysis in terms of the bulk modulus and all the shear moduli is not yet available. In a first approximation in which only one parameter is used, there is no obvious theoretical reason to prefer the shear modulus over the bulk modulus. The bulk modulus is a much more convenient parameter for use in predicting Qm. Shear moduli are known for less than half of the metallic elements while bulk moduli are usually available. Furthermore, because of the directional dependence of shear moduli, their estimation for alloys appears inherently more difficult than is the estimation of bulk moduli. We assume that the bulk modulus Bs reflects an average value of the shear moduli such that the strain energy at the point of maximum distortion of the lattice during vacancy migration can be expressed as

Jan 1, 1964

By H. A. Bright, H. C. Vacher, J. G. Thompson

The methods employed for the determination of oxides and oxygen in ferrous materials may be roughly classed in two groups, "wet" methods and "hot" methods, the first group including the iodine, electrolytic, mercuric chloride, hydrochloric acid, nitric acid, and chlorine methods; the second group including the vacuum-fusion and hydrogen-reduction methods. The wet methods depend upon preferential solubility in a selected medium to separate the metallic portion of the sample from the oxygen-containing constituents. Subsequent analysis of the insoluble residue permits the isolation and separate determination of individual oxides and compounds. The hot methods depend upon the reduction of the oxide constituents of the sample by means of carbon or hydrogen at elevated temperatures. With the exception of the recently developed fractional vacuum-fusion method, the hot methods do not identify individual oxides and compounds but yield only a single value representing the sum of the oxygen contents of several or all of the oxide constituents present. With such diversity in the principles and aims of the different groups, it is not surprising that concordance of results by different methods has usually been difficult to obtain. The present cooperative attempt to define more rigorously than has been possible heretofore the accuracy and limits of usefulness of the various methods, originated in correspondence between Dr. John Johnston, Director of Research of the United States Steel Corporation, and other interested metallurgists. The plan was, briefly, to submit identical samples to a number of laboratories for analysis by different methods and to collate the results of these analyses. The project was endorsed by the Iron and Steel Division of the American Institute of Mining and Metallurgical Engineers at the annual meeting in February, 1933, and has been conducted under the joint sponsorship of the Iron and Steel Division and the National Bureau of Standards. The latter organization undertook

Jan 1, 1937

By Nicasio del Castillo

INTRODUCTION The tax structure of foreign mining investment into the United States has a significant impact on the financing and the profitability of the operation. For these reasons, it is critical for the foreign investor to develop and implement a well planned tax strategy that will enable its venture to: (1) reduce its U.S. income tax liability (2) lower U.S. withholding taxes when funds are transferred from the United States, and (3) decrease or defer home country taxation on its U.S. earnings ALTERNATIVE FORMS OF INVESTMENT A threshold business and tax consideration is the form in which the investment is to be made. The most common alternatives include: forming or acquiring a U.S. mining corporation, directly establishing a branch mining operation, or entering into a joint venture or partnership with a U.S. mining company. U.S. Corporations The most common structure through which foreign mining companies engage in business in the United States is to form a U.S. mining corporation. Forming a U.S. Corporation. If the investor decides to establish a new U.S. corporation the organization is relatively simple. No distinctions are made in the United States between "public" and "private" forms of incorporation. Minimum share capital is not usually required and share capital may consist of shares with no par value. Since corporate law is the responsibility of the individual states, the foreign investor must choose a state in which to incorporate. If appreciated mining property is transferred to a corporation solely in exchange for stock or securities in that corporation, and the transferors have control of the corporation (defined as at least 80 percent of all voting shares and at least 80 percent of all other shares) immediately after the exchange, no gain or loss will be recognized. However, if the transferors receive cash or other mining properties in addition to stock, any resulting gain may, in certain situations, be taxed to the extent of the cash and the fair market value of other property received. Acquiring an Existing U.S. Corporation. Acquiring an existing U.S. mining corporation is not as straight-forward as forming a corporation. This alternative may be accomplished through either a stock or an asset acquisition. Generally, with a stock acquisition the purchaser inherits all of the business and tax attributes of the former mining corporation. If the investor is able to acquire mining assets, however, the purchaser will usually be able to avoid any unknown or hidden liabilities that could be attached to an existing corporation. Another principal advantage in acquiring assets is that the purchase price may be directly allocated to the acquired mines or other mineral-related assets with the result that the assets' depreciable base may be increased. Assuming the domestic seller and the foreign purchaser can agree, it is generally advisable to allocate the purchase price in the sales agreement to specific individual assets. From the foreign investor's standpoint, it is preferable to allocate the purchase price to depreciable assets such as buildings and equipment versus an allocation to mineral land holdings or intangibles such as goodwill, which are generally not depreciable. It is not uncommon, however, for a seller mining company being acquired to insist for tax reasons that the investor purchase shares rather than assets. If the foreign

Jan 1, 1985

By Frederick Crabtree

WHEN Professor Stock asked for a paper on the above subject, it was too late to prepare by June 1, or near that time, one that would involve any appreciable amount of experimental work or original research; but the suggestion was made that a review of the literature bearing on the subject might be submitted in good time, and that later this could be supplemented by any experimental data obtained during the summer, if experiments were carried out. In accordance with this suggestion, there are submitted the following notes on references found in the literature of recent years bearing on sulfur in gas. It is to be, understood that, ill general, these notes express the opinions of the authors whose papers are abstracted, not necessarily the opinions of the abstractors. Very little published information was found bearing directly on producer-gas sulfur, so this has been supplemented, in certain phases of the subject, by references to illuminating gas. Methods of analysis and processes for the elimination of sulfur from the gas are, without much doubt, very closely related in these two products. As in illuminating gas, sulfur is found in producer gas mainly as hydrogen sulfide, mixed with a much smaller and variable quantity of carbon bisulfide.1 The presence of minute quantities of other organic-sulfur compounds has been intimated, but no definite statement is made concerning these. The amount of sulfur present in producer gas is variable and depends on several conditions. The primary factor is the quantity of sulfur in the fuel, but the form in which the sulfur exists, the temperature of the producer, the air-steam ratio, and the efficiency of the scrubbing process are all determining factors. When the coal used contains less than 0.5 per cent. of sulfur, the sulfur in the gas will not exceed the quantity found in the average illuminating gas.2 Sulfur in producer gas may safely

Jan 9, 1919

By Ulf S. Landergren

Diffusion coefficients and marker movements have been determined in brass using welded couples. Three different concentration ranges were employed at 750°C, while a fourth concentration range was measured at 500°, 600°, 700°, and 800°C. Marker displacements toward and porosity development in the high zinc side of the couple were observed in all cases. The results were interpreted as favoring a vacancy diffusion mechanism. IN the large amount of diffusion literature which has accumulated during the past half century, very few experimental data have been presented on body-centered-cubic metallic phases. The impressive combination of experimental and theoretical studies which has given the vacancy mechanism a fairly secure position as the preferred mechanism for most face-centered-cubic metals has no counterpart for body-centered-cubic phases, although the theoretical picture seems to be in a better state than the experimental work. The attempts to select diffusion mechanisms by the theoretical calculation of the activation energy for the various conceivable unit diffusion processes and the energy of formation of the type of lattice defect required have been based on models of two kinds. The first kind utilizes potential functions fitted for certain properties of pure crystalline copper; the second kind is fitted for sodium. The latter is an example of an open metal in which the metallic ion is small compared with interatomic distance,&apos; while the former is characteristic of the larger class of metals in which the ions have diameters about as large as the interatomic distance. brass should resemble copper in this fundamental property. It should be evident that results on the mechanism of diffusion obtained for one of these classes need not necessarily apply to the other. Huntington and Seitz, using a model of the copper type, showed that the activation energies to be expected for interstitial migration or a two-atom direct interchange were much higher than that for vacancy diffusion. Zener pointed out that a four-atom ring rotation would involve an activation energy considerably lower than the two unlikely mechanisms although still higher than the vacancy mechanism in the face-centered-cubic structure. Furthermore, he argued, the four-atom rotation would be relatively easier in a body-centered-cubic lattice and might be competitive with the vacancy mechanism. Paneth showed that a body-centered-cubic crystal-like sodium could form interstitial defects of special type, called a crowdion, by crowding an extra atom into < 111 > directions where the defects would affect a line of about eight atoms. The defect was constrained to move along the defining line. Unlike the face-centered-cubic case, therefore, the theoretical calculations for the body-centered-cubic mechanism do not provide a very clear-cut answer, and the absence of adequate experimental studies is the more serious. This investigation was undertaken for the purpose of obtaining useful information on diffusion in body-centered-cubic phases. brass was chosen for several reasons: 1—the phase field is sufficiently wide at high temperatures to permit the use of diffusion couples with adequate concentration ranges for satisfactory chemical analysis, 2-—thermodynamic activity data are available for the calculation of mobilities from diffusion coefficients, 3—the phase is as close to the theoretical model of the copper -type on which the calculations have been done as any body-centered-cubic metallic phase is likely to be. Measurements of the movements (if found) of inert markers during the diffusion process would indicate that a vacancy or Or mechanism played a major role in diffusion in brass. If no marker movement should be found, a ring mechanism would be indicated but not assured. Experimental Procedure The alloys used in these experiments, listed in Table I with analyses, were supplied by the Naval Research Laboratory. They were from ingots of 3x3 in. cross-section, heated to 760°C, reduced under a

Jan 1, 1957

By R. D. Fisher, A. G. Metcalfe, F. A. Crossley

AN investigation of the application of magnetic stirring to the consumable arc melting of aluminum and nickel demonstrated that grain refinement could be obtained when there was sufficient stirring force. Also, it was found that grain refinement could be obtained in aluminum by alternately reversing the polarity of the current through the magnetic stirring coil. The effect of the latter was to periodically reverse the direction of rotation of the molten metal.&apos; Because of their promise, these findings were applied to conventionally cast aluminum. Shortly after this work was begun, Kondic2 reported experiments in which aluminum cast with 40° C (72° F) of superheat exhibited a grain size of 10 to 20 grains per cm2. When interrupted rotation was applied during solidification by mechanical means, a grain size of 800 to 1000 grains per cm2 was obtained. Magnetic Stirring Applied to Conventional Casting— The applicability of magnetic stirring to producing grain refinement in conventionally cast metal was evaluated in the following way. Three pounds of aluminum were cast into a clay-bonded graphite mold. The mold was surrounded by a magnetic stirring coil of 1000 turns. A direct current of 200 amp was passed through the casting by means of a graphite electrode which was immersed from the top. A current of 5 amp was passed through the stirring coil. The aluminum (1100 or 25) was superheated to 1600° F (871° C) and fluxed by passing chlorine gas through the melt for 2 min prior to casting. Two additional castings were made for comparison: 1) a conventional casting of metal superheated to 1600° F and 2) a similar casting through which 200-amp current was passed during solidification, but without current in the magnetic coil. Macrosections of these three ingots are shown in Fig. 1. Very remarkable grain refinement resulted in the magnetically stirred casting. It may be noted that the casting through which 200-amp current was passed has a coarser structure than the conventional casting. It would appear that this is due to the additional heat input generated by the current to the former casting. Mechanical Rotation Applied to Conventional Casting—A casting temperature of 1600° F was used throughout. Some 1 1/2 -lb castings rotated at 150 rpm were predominantly columnar with small areas of coarse, equiaxed grains close to the lower mold wall. Following these, a series of 3-lb castings was made. Macrosections of these ingots are shown in Fig. 2. The imposed rotational speed was 250 rpm. Turbulence or acceleration in the solidifying liquid was the significant factor. Fine grain size resulted in the material solidified during the period of acceleration of the liquid to the imposed rotational speed. When uniform rotational motion was achieved, the grain structure reverted to columnar. The final casting shown in the lower right-

Jan 1, 1962

By W. T. Thom

All engineering education is faced by certain basic problems, three of which seem to have particular present importance in geological engineering training in general, and in respect to training for oil field geo-exploratory work in particular. Problem i The first of these problems has to do with present and future educational objectives and with the numbers and qualities of the men who should be coming out of our geo-exploratory training programs. Before the war we needed ever-increasing numbers of graduates at the Bachelor&apos;s level and a very much smaller number of men who had reached the Doctorate degree. Now, with more difficult, more extensive, and more costly exploratory work; with a rapid expansion of company "staff" activities, and with the initiation of many new research organizations and laboratories; it is clear that men of exceptional ability will be more and more in demand, and that the schools will need to carry a greater proportion of their students through to the Ph.D, degree. Problem 2 Assuming that the mineral industries will need an increasing supply of well-qualified Ph.D.s for future geoexploratory work (staff, line and research), can the schools expect to provide this supply of able Ph.D.s merely by expanding the proportion of B.S. and B.A. majors who go on through to the doctorate stage of training? And the answer is definitely "No"—as the situation stands at present. Most A.B. graduates are years short of the preparations in basic science and elementary engineering prerequisite to effective graduate study in the geoexploratory fields (paleontology ex-cepted), and similarly many of the annual crop of B.S. graduates lack adequate training in English; in ancient and modern history; and in the modern principles of labor and public relations. Indeed, several basic problems of undergraduate curricular organization and integration remain to be solved before most recipients of a Bachelor&apos;s degree will have that sound and broad educational foundation prerequisite to graduate training on a really effective basis. It is for these reasons that we have continued to experiment with our geological engineering program at Princeton, in an endeavor to provide a pilot-plant demonstration of a suitably broad and flexible undergraduate curriculum. Problem 3 But assuming that the schools can and do get undergraduate curricula set up in proper phase and scale to meet needed enrollment quotas for graduate training, what about the most urgent part of our whole mineral-industry educational problem? What about finding and bringing into mineral-industry training those youngsters of superior ability who are, by potential or known inclination, especially well-qualified for geoexploratory work?

Jan 1, 1949

By Alexandre Pourcel

The phenomena of liquation in steel or iron ingots of all sizes, but naturally to greatest extent in the heaviest ingots, have been noticed ever since the commencement on a large scale of the Besse mer and open-hearth manufactures; but they have been studied with care during the last few years only. The English and the Ameri cans were the first to publish the results of investigation upon phe nomena of this clam, to which they have given the name of segregation. Historical. Passing by that which has been written concerning the segregation observed in gray pig-iron, of which instances were given by Karsten, we shall confine ourselves here to that which is known of this subject with exclusive reference to ingot steel and iron. Mr. H. M. Howe, of Boston, in his Metallurgy of Steel, the most complete and well-arranged treatise upon steel, gives a resume of observations, with the results of numerous analyses, bearing upon the phenomena of segregation. According to Tchernoff (with whom we discussed this question at length in 1878, in connection with the cast-steel plates of large dimensions designed for the Italian fleet, which we showed him at Terre-Noire), Kalakoutsky called attention in 1866 to the lack of homogeneity in Bessemer ingots, especially when cast in sand. Our own attention had been called to the phenomena of liquation in 1868 by a somewhat surprising fact which appeared in almost every one of a number of steel-rail ingots coming from the works of Messrs. Pierre and Emile Martin at Sireuil, to be rolled at TerreNoire. In the heating or in the first groove of the rolls, a slice of from 6 to 10 centimeters (2.4 to 3.9 inches) separated itself from the head of each ingot. As a general consequence, the section of

Jan 1, 1894

By W. B. Braden

This paper presents a suitable method for predicting gas-free oil viscosities at temperatures up to 500F knowing only the API gravity of the oil at 60F and the viscosity of the oil measured at any relatively low temperature. The API pravity and the one viscosity value are used as parameters to determine the slope of a straight line on the ASTM slanaord viscosity-temperature chart. Then, knowing the slope of the line and one point on the line, the vrscosities at higher temperatures can be determined. The line slope correlations were developed at I00 and 210F since viscosity data are frequently measured at these temperatures. A procedure is given for predicting line slopes from measurements at other tetnperatures. A nomogram is furnished for solving the relationship. The correlation has been evaluated at temperatures up to 5OOF for oils varyzng in gravity from 10 to 33 " API. The correiution is applicable only to Newtonian fluids. Comparison at 500F of true viscosities and those predicted from values at 100F shows an average deviation of 3.0 per cent (maximum deviation of 6.0 per cent). Predictions from the values at 21 0F for the same oils how an average deviation of 1.5 per cent (maximum deviation of 3.4 per cent). INTRODUCTION Correlations have been developed by Beal&apos; and by Chew and Connally&apos; for predicting viscosities of gas-saturated oils at reservoir conditions. Each of these correlations requires a knowledge of the solution gas-oil ratio and the viscosity of the gas-free oil at the reservoir temperature. For temperatures below 350F, measurements of the gas-free oil viscosities can be made easily using commercially available equipment. In thermal recovery processes, however, reservoir temperatures well in excess of 350F are encountered. Viscosity measurements at such conditions are more difficult and time consuming and require modification of existing equipment or the construction of new equipment. Measurements are further complicated by the difficulty of handling highly viscous oils associated with thermal recovery processes. Therefore, it is desirable to have a correlation which allows accurate prediction of viscosities at high temperatures. A commonly used technique for predicting viscosities at high temperatures is to measure the viscosities at two lower temperatures, plot the values on ASTM standard viscosity-temperature charts and extrapolate to the temperatures desired. If either of the values is slightly in error, the extrapolated value can be significantly in error. To justify an extrapolation, three points are actually necessary. This procedure can consume much time, particularly with heavy oils. Considering the cost of viscosity measurements, it would be desirable to eliminate the need for direct measurements by having correlations which would allow viscosity predictions from other physical or chemical properties. Beal1 investigated the possibility of correlating viscosity with oil gravity at temperatures from 100 to 220F. While showing that a general relationship exists, he also found significant deviations. It is possible that correlations will be developed based on oil composition as more information becomes available. While not eliminating the need for viscosity rneasurements, the method presented herein requires that only one viscosity measurement be made. The API gravity must also be known. The theory is based on the fact that the viscosity of paraffins (high gravity) changes less with temperature than does the viscosity of naph-thenes or aromatics (low gravity). The gravity. therefore, is used as a parameter to determine the slope of a straight line on the ASTM standard viscosity-temperature charts. The correlation is applicable only to Newtonian oils, and deviations due to thermal decomposition and nonhomo-geneity cannot be predicted. Oils containing additives have not been evaluated. PROCEDURE Fifteen oils were used in developing the correlation; eight were crudes and seven were processed oils. Oil gravities varied from 9.9" API (naphthene base) to 32.7&apos; API (paraffin base). The temperature range studied was 81 to 516F. Each oil used had a minimum of three viscosity measurements and each plotted essentially as a straight line on the ASTM charts. In all, 91 viscosity measurements were used in the correlation. Saybolt, rolling ball and capillary tube viscometers were used for the measurements. Viscosity data for Samples 1, 2, 4, 7, 10, 11 and 14 were obtained in Texaco, Inc. laboratories. The data for Samples 3, 5, 6, 8, 9, 12 and 15 were from Fortsch and Wilson,3 and data for Sample 13 were from Dean and Lane.&apos; All data points used in the correlation are plotted in Fig. 1. It is seen that some of the viscosity values deviated slightly from the straight-line plots at the higher temperatures. Properties of the oils after exposure to the

Jan 1, 1967

By E. F. Northrup

THESE brief notes respecting the properties of pure tin that make it useful as a pyrometric substance summarize information gathered by the writer In an extensive experimental investigation on the electrical properties of metals in the molten state. Tin in quantities sufficient for pyrometric purposes may be obtained at relatively low cost and in a state of high purity. The metal melts at 232° C. and, according to determinations made by Greenwood,. 1909, does not begin to boil until a temperature of 2270° C. is reached. The writer can assert, from personal observations carefully made, that tin shows no tendency to boil at a temperature of 1680° C. If Greenwood&apos;s observations are correct the temperature interval, 2038° C., in which tin exists as a liquid under atmospheric pressure, exceeds that of any other substance. It has never been observed, as far as the writer is aware, that tin forms any chemical union, as carbide, with carbon at the highest temperatures at which it can exist as a liquid. It is quite certain from the writer&apos;s personal observation that tin heated in Acheson graphite to 1680° C. remains chemically uncontaminated. Wires of pure tungsten do not dissolve in molten tin at temperatures at least as high as 1680° C. Tungsten wires or rods may, therefore, be used as electrodes dipping into molten tin when required for measuring the resistance of the molten metal at very high temperatures. When tin is raised to a high temperature in a covered graphite container, the CO atmosphere that exists above its surface has a reducing action, which maintains this surface of mirror brightness. Incidentally, tin maintained molten in a crucible of Acheson graphite makes a most excellent bath into which may be inserted several pyrometers that are to be intercompared at the same temperature.

Jan 8, 1919

By Shiou-Chuan Sun

THE effects of oxidation on the flotation behavior of sulphide minerals have been extensively studied,1-3 but no similar study has been made of coals. Coals of bituminous and lower rank undergo atmospheric oxidation during mining and storage, and their degree of oxidizing increases with temperature4,5 and time of exposure.6 The problem of recovering fine oxidized coal from culm piles, rivers, and streams by froth flotation has become increasingly important to the coal industry as well as to those concerned with air and stream pollution. This paper describes the flotation behavior of oxidized and unoxidized coals and carbons in the presence of oily collectors and presents the reagents found effective in the flotation of oxidized coals and carbons. Except where otherwise stated, flotation tests were performed in a 50-g Denver flotation cell. Solid feed for each test was 30 g, and the pulp dilution was kept at 8.5. The -65 mesh coal sample was wetted by agitation with water in the flotation cell for 6 min, then conditioned with a predetermined amount of collector for 2 min, and finally floated with pine oil as frother for 3 min.

Jan 4, 1954

By Axel Hultgren, B. Herrlander

THE original aim of the present investigation was to study the mechanism of cracking on hot-deforming red-short steels. During the microscopical examination of hot-deformed soft steels attention was directed to various patterns of so-called veining in the ferrite, as related to variations in the deformation procedure and the heat-treatment of the steels. Later, a hot-short steel of higher carbon content was also studied. Historical Storey1 suggested in 1914 that veining developed during the gamma-alpha transformation from the growing together of several alpha nuclei within the same gamma grain. Rawdon and Berglund2 found that in soft steel, forged somewhat below A3, the ferrite showed profuse veining, while usually there was very little veining after forging at very high temperatures. They emphasized the similarity between the pattern of veining formed by deformation about 600°C and that of slip lines formed by deformation at room temperature. They also suggested a relation between the gamma-alpha transformation and veining. They became convinced from etching and from the slip-line pattern in cold-deformed material, that the orientation within any ferrite grain showing veining was uniform. In recrystallized alpha grains veining was absent. Veining did not appear materially to affect the properties of ferrite. Independent of veining, continuous networks, attributed to preexisting delta and gamma grain boundaries were sometimes found, the former only in cast steel. Those networks were usually connected with small inclusions. Ammermann and Kornfeld3 confirmed that recrystallized ferrite grains showed no veining. In soft steel annealed between At and A3 there was veining only in the ferrite grains formed during cooling. Electrolytic iron deformed at 880° was free from veining. Bannister and Jones4 considered veining in ferrite to be a manifestation of microscopical and submicroscopical inclusions. Northcott,5,6 in studies on veining in steel and other metals and alloys, attributed veining to oxide inclusions. It could generally be removed by annealing in hydrogen, a suggestion earlier made by Rawdon and Berglund. Tritton (discussion in ref. 5) emphasized the importance of perfect polishing for bringing out veining by etching, and thought the veins or subboundaries were produced during the gamma-alpha transformation, when it was rapid, as a result of the volume change and contraction during cooling.

Jan 1, 1946

"The Butte, Anaconda & Pacific railway extends from Butte to Anaconda. The electrification comprises 30 miles of main line single track, and includes sidings, yard and smelter tracks. When complete the electrified trackage will total about 90 miles on a single track basis.The traffic conditions are unusually severe as they consist principally of hauling copper ore from the Butte mines to the smelters at Anaconda, as well as hauling all the mine supplies, lumber, etc., in both directions; this traffic amounts to approximately 5,000,000 tons of freight per year. The maximum grade against the load is .3 per cent and the maximum train consists of 50 loaded steel ore cars, weighing 3,400 tons. .The locomotive units, two of which will be used for freight trains, weigh approximately 80 tons each. In addition to the freight business, there will be a certain amount of passenger traffic.The power for operating the Butte, Anaconda & Pacific railway is generated by, the Great Falls Power company, and is transmitted to the sub-stations at 100,000 volts. The synchronous motors are supplied with power at a potential of 2,300 volts, 60 cycles, 3-phase. Voltage regulators are installed in each sub¬station to secure the benefit of synchronous condenser effect of the motors.The passenger and freight locomotives are exactly similar, with the exception of the gearing.The roller pantograph mounted on the top of the cab is operated by air from the engineers position.The adoption of the 2,400-volt apparatus for so important a system, where the conditions of operation are so severe, is interesting of itself, as indicating the trend that future electrifications of importance may follow. A trolley potential of 2,400 volts was only adopted after a thorough investigation of other systems already in operation."

Jan 1, 1913

By M. J. Sinnot, J. C. Shyne

Low-frequency mechanical damping measurements were made to investigate internal friction in Fe-A1 alloys. The atomic ordering of the Fe-A1 system strongly influenced the stress-induced ordering internal friction. Magnetoelastic damping was also encounteyed and was shown to be reduced by the application of a static stress. THIS paper describes some damping experiments made on alloys of Fe and Al. Stress-induced ordering internal friction was measured with samples containing from 9.8 to 31.3 at. pct Al. Aluminum is soluble in a-Fe to about 50 at. pct and forms at least two long-range ordered structures, Fe3Al and Feu.&apos; Stress-induced ordering internal friction is known to occur in many substitutional solid solutions, but few measurements of this damping effect have been made with alloy systems that have pronounced ordering tendencies. LeClair and Lomer developed expressions relating the relaxation strength of the damping process to the degree of atomic ordering and predicted that stress-induced ordering internal friction would be zero with complete ordering.&apos; This concept was confirmed experimentally by Lulay and Wert using the system cd-Mg It is also consistent with the weak stress-induced ordering peaks observed in P -brass by Artman and in 16 wt pct Al Fe-Al by bert.&apos; It was expected, therefore that the ordering characteristics of the system Fe-Al would strongly influence the stress-induced ordering internal friction exhibited by the experimental alloys. SAMPLE PREPARATION The alloys used in this investigation were induction melted under vacuum using high-purity melting stock. The iron was electrolytically refined Plastiron 101 which contained 99.85 wt pct Fe. The aluminum was a special 99.95 pct pure grade supplied by Alcoa. The only other raw material was spectrographically pure graphite which was used in small quantities as a deoxidant. The amount of carbon used was slightly in excess of the amount required to completely deoxidize the melt; this resulted in residual carbon contents of 0.01 to 0.02 pct in the finished alloys. The vacuum cast 2 1/2-in. diam ingots were hot rolled to 5/8-in. diam round bars. Portions of these bars were hot swaged and hot drawn to 0.050-in. diam wire. Straight pieces of the hot drawn wire were slowly heated to a temperature of 1300°C in a He atmosphere. After holding for 4 hr, the samples were allowed to cool in the furnace. This annealing treatment resulted in grain growth in the samples, the final grain size being about the same as the wire diameter. The grain boundaries were oriented perpendicularly to the wire axis, giving a bamboo grain structure. The existence of a preferred orientation could not be detected in these coarse grained samples. If the samples had a fiber structure, this probably would have been the same in all samples because of similar processing, thus the influence of crystal orientation on the relaxation strength would have been similar in all samples. The aluminum contents of the alloys are listed in Table I. EQUIPMENT The principle of the torsion pendulum was used for the internal friction measuring device. The

Jan 1, 1961

By AIME AIME

THE week, of April 5 will long be remembered by those that attended the Birmingham meetings of the Open-Hearth and Blast Furnace committees of the A.I.M.E. Iron and Steel Division. Birmingham iron and steel own received the 450 delegates with open arms; described and discussed their southern metallurgical practices and problems and compared experiences with their northern brother metallurgists in two days of technical sessions on Wednes-

Jan 1, 1937