Search Documents

By Benjamin Smith Lyman

THE importance of topography to geology is so commonly underrated as to deserve to be pointed out again and again. The relation of topography to the different branches of geology may be seen best by a glance at them all. Geology is well understood to consist of the observation of facts about rocks as materials of the earth (geognosy), and the explanation of those facts (geognosy). The facts to observe are : I. GEOMETRICAL, as (1) structure, including the dip and strike at different points, the size, shape, and position of basins and saddles; (2) vertical section, that is, the thickness of rock groups and of their parts ; (3) horizontal or geographical position. 11. PHYSICAL, such as texture, whether sedimentary or crystalline ; and, if crystalline, whether granitic, porphyritic, amygdaloidal, globular, or concretionary ; whether compact or granular; coarse or fine; pervious or impervious; hard or soft; firm or tender; with cleavage or without ; massive or thin ; the microscopic structure ; also whether magnetic or not ; soluble or insoluble ; fusible or infusible ; and the constituent minerals. 111. CHEMICAL that is, the composition of the rocks and of their minerals and their affinities. IV. PALAENTOLOGICAL, as what kind of fossils are in the rocks,

By R. A. Morse, P. M. Bridges, L. E. Wilsey, Howard N. Hall, P. L. Terwilliger

Theoretical and experimental investigations of a constant pressure gravity drainage system are reported. Experimental data are presented to show that recovery to gas breakthrough by gravity drainage is inversely proportional to rate. The gravity drainage reference rate, which is numerically equal to the so-called "maximum theoretical rate of gravity drainage" is shown to have no particular significance from a recovery standpoint. Before this rate can be used as a basis of comparison for recoveries, it is necessary that the relative permeability and capillary pressure characteristics and displacing fluid viscosities be identical for the systems compared. A method is presented by which accurate prediction of the performance of a gravity drainage system can be made. Close agreement between experimental and calculated drainage performance shows that steady state relative permeability and static capillary pressure data can be used to describe fluid displacement behavior. The very wide range of liquid recoveries before gas breakthrough which result from production rate variation alone demonstrates the importance of this factor in planning depletion of a gravity drainage reservoir. Calculated results are presented which show that little additional recovery can be expected from a high pressure gravity drainage system between the times of gas breakthrough and attainment of such high gas/liquid ratios as to make further pressure maintenance impractical. INTRODUCTION It bas been recognized for some time that gravity forces play an important part in the recovery of oil from some types of reservoirs. Field experience has shown that under certain conditions, gravity drainage can result in very high oil recov- eries. Qualitative reasoning has led most engineers to the general conclusions that: (1) Where gravity drainage is important, the reservoir pressure should be maintained by gas injection at the crest of the structure to prevent shrinkage of the oil in place and to keep a low viscosity so the oil can drain at the fastest possible rate. (2) Recovery by gravity drainage is rate sensitive. A survey of the literature indicates that while considerable work has been done on the effects of gravity in oil production problems, no satisfactory method of calculating the performance of gravity drainage reservoirs has been reported.1,2,3,4,5 In the absence of any proven method of calculating reservoir performance, the level at which pressure should be maintained and the rate of production for most efficient operation has been open to debate. The limits and general character of the recovery us rate relationships are apparent from the following: As rates of production approach zero, oil will drain by virtue of its own weight fast enough that the saturation distribution is always approximately the same as the original static capillary distribution. That is, at the gas-oil contact the liquid saturation goes from 100 per cent to a value of perhaps 10 to 30 per cent in a very short distance, so that as production continues. a relatively sharp gas-oil contact moves down-structure, leaving a very low residual oil saturation in the originally oil saturated zone. At very high rates of production, the oil that drains by virtue of its own weight is negligible and recovery will approach that of a horizontal gas drive, leaving a much higher residual oil saturation. At intermediate rates of production. recovery should be between these extreme*. Despite the lack of quantitative methods, tentative agreement had been reached on the question of optimum producing rate. It has been generally concluded that rather sharp decrease in recovery would occur at rates of production above the "maximum rate of gravity drainage" and hence this rate should not be exceeded. The "maximum rate of gravity drainage" is defined as the rate of production from a 100 per cent

Jan 1, 1951

By L. E. Wilsey, R. A. Morse, P. L. Terwilliger, Howard N. Hall, P. M. Bridges

Theoretical and experimental investigations of a constant pressure gravity drainage system are reported. Experimental data are presented to show that recovery to gas breakthrough by gravity drainage is inversely proportional to rate. The gravity drainage reference rate, which is numerically equal to the so-called "maximum theoretical rate of gravity drainage" is shown to have no particular significance from a recovery standpoint. Before this rate can be used as a basis of comparison for recoveries, it is necessary that the relative permeability and capillary pressure characteristics and displacing fluid viscosities be identical for the systems compared. A method is presented by which accurate prediction of the performance of a gravity drainage system can be made. Close agreement between experimental and calculated drainage performance shows that steady state relative permeability and static capillary pressure data can be used to describe fluid displacement behavior. The very wide range of liquid recoveries before gas breakthrough which result from production rate variation alone demonstrates the importance of this factor in planning depletion of a gravity drainage reservoir. Calculated results are presented which show that little additional recovery can be expected from a high pressure gravity drainage system between the times of gas breakthrough and attainment of such high gas/liquid ratios as to make further pressure maintenance impractical. INTRODUCTION It bas been recognized for some time that gravity forces play an important part in the recovery of oil from some types of reservoirs. Field experience has shown that under certain conditions, gravity drainage can result in very high oil recov- eries. Qualitative reasoning has led most engineers to the general conclusions that: (1) Where gravity drainage is important, the reservoir pressure should be maintained by gas injection at the crest of the structure to prevent shrinkage of the oil in place and to keep a low viscosity so the oil can drain at the fastest possible rate. (2) Recovery by gravity drainage is rate sensitive. A survey of the literature indicates that while considerable work has been done on the effects of gravity in oil production problems, no satisfactory method of calculating the performance of gravity drainage reservoirs has been reported.1,2,3,4,5 In the absence of any proven method of calculating reservoir performance, the level at which pressure should be maintained and the rate of production for most efficient operation has been open to debate. The limits and general character of the recovery us rate relationships are apparent from the following: As rates of production approach zero, oil will drain by virtue of its own weight fast enough that the saturation distribution is always approximately the same as the original static capillary distribution. That is, at the gas-oil contact the liquid saturation goes from 100 per cent to a value of perhaps 10 to 30 per cent in a very short distance, so that as production continues. a relatively sharp gas-oil contact moves down-structure, leaving a very low residual oil saturation in the originally oil saturated zone. At very high rates of production, the oil that drains by virtue of its own weight is negligible and recovery will approach that of a horizontal gas drive, leaving a much higher residual oil saturation. At intermediate rates of production. recovery should be between these extreme*. Despite the lack of quantitative methods, tentative agreement had been reached on the question of optimum producing rate. It has been generally concluded that rather sharp decrease in recovery would occur at rates of production above the "maximum rate of gravity drainage" and hence this rate should not be exceeded. The "maximum rate of gravity drainage" is defined as the rate of production from a 100 per cent

Jan 1, 1951

By Henry Fernald

THE accounting system or bookkeeping methods of any company are principally the concern of that company and of those who are in control of its affairs. Its published financial report is, however, primarily intended for those who are not already fully informed regarding its operations and finances. Whatever may be the advantages of standardization of accounting and bookkeeping methods, it must be admitted that a company has a certain right to handle its accounts and keep its books and records in whatever manner may seem to it best adapted to its affairs, even though such methods may differ materially from those generally adopted by others. In its financial reports it should not, however, either ask or expect that the statements it makes or the terms which it uses will be given in its case a meaning and interpretation different from that which they are ordinarily considered to have in similar reports and statements of other companies. The particular form and arrangement of such reports is a matter concerning which there may be much difference of opinion. It is of little importance whether current assets come first or last in the Balance Sheet, but it is important that there should not be included under this designation any items which are not properly current assets within the generally accepted meaning of that term. The extent to which stockholders or others interested are to be made acquainted with the full details of a company's business is a question which the proper authorities must in each case decide. It should, however, be recognized that there are certain facts regarding a mining com-pany which must be set forth in a financial statement if it is fully to cover the conditions and affairs of the company. For example, a financial, statement which does not include or is not accompanied by a statement, of the ore reserves of the company does not fully set forth its financial condition. This is true whether the absence of such a statement of ore reserves is because it is not desired to make public the figures or whether it is because the ore reserves themselves are not definitely known, or accurately measured.

Jan 1, 1928

By E. Nelson Fell

As this plant is the first ever erected in British Columbia for the treatment of tailings by the cyanide process, and as the ores of this, mine are of a character not unusual among gold-ores of this Province, it is probable that a description of the principal features of the plant, and of the methods employcd in its operation, may be interesting. These works were designed after a careful study of the process, in a small experimental plant, for a period of six months. During this period ten percolation-tests on charges of tailings of 1100 lbs. each, eight percolation-tests on similar charges of concentrates, and twenty-six tests 011 concentrates in a revolving barrel, were made, besides laboratory-experiments. The ore consists of a quartz gangue, containing a little lime and variable quantities of the sulphidcs of iron, lead and zinc. The following figures, giving the analyses of the ore before milling, and of the tailings after milling, which constituted the material to be cyanided, are based on the daily samples taken during February and March, 1901.

Jan 1, 1902

By H. R. Hanley, Charles Y. Clayton

ONE of the most important contributions to the art of electrolytic zinc production has been the aluminum cathode. This has been used in all major production since its commercial development in 1916. The literature is replete with important contributions, some of which may have been replaced by better ones, but thus far there appears no other metal to take the place of aluminum as cathode material. Credit for this innovation goes to Sherard Cowper Coles, of England. When experi¬menting on the extraction of zinc from Broken Hill ore at Hayle, Cornwall, in 1893, he introduced the aluminum cathode, and in 1895 obtained British Patent No. 20073. The reason for this dominant position of aluminum as cathode material in zinc sulphate electrolytes is its unique surface, to which electrodeposited metals usually do not tightly adhere. The metal must be of high purity for best results. It is possible to develop a starting-sheet method by which thin electrodeposited sheets of cathode zinc are made and stripped from a smooth aluminum plate. Such thin sheets of cathode zinc may be used as are the copper sheets in standard electrolytic copper-refinery practice. However, complications arise because of extreme warping of the zinc starting sheet after a few hours of deposition, and thus special arrangements must be made to compensate for this abnormality. Reasons advanced for the ease with which deposits may be stripped from the aluminum surface are: (1) presence of a permanent oxide coating on the metal, (2) failure of aluminum to alloy with the deposit, (3) differences in coefficient of expansion, (4) high position of aluminum in the electromotive series of metals. Of these reasons for nonadherence, which may have some application in general deposition, probably the oxide coating has the greatest bearing on the subject of zinc deposition. Adherence of zinc deposits has occasionally had serious effect oil tonnage and production costs. Opinions have differed as to the specific

Jan 1, 1938

By F. J. Fayers, S. A. Hovanessian

The one-dimensional displacement equation for a homogeneous porous medium, including the effects of gravity and capillaty forces, has been solved by a numerical method. A finite-difference scheme is developed for obtaining saturation, pressure and fractional flow profiles in waterflood recovety problems. From the numerical examples given, it is concluded that the gravitational forces have a pronounced effect on the saturation profiles and the pressure distribution curves of the system. INTRODUCTION Within the past 20 years, a number of papers have appeared in the literature dealing with the quantitative treatment of waterflood recovery problems. In their celebrated paper, Buckley and Leverett1 described a method for calculating saturation profiles when the effects of capillary pressure and gravity are excluded. Terwilliger, et al,2 included the effect of gravity in their theoretical and experimental investigation of oil recovery problems and obtained close correlation between experiment and theory. welge3 described a simplified method for obtaining the average saturation and the oil recovery from an oil reservoir. The effect of gravity can be included in this calculation. More recently (1958) Douglas, et al,4 presented a method for calculating saturation profiles which includes the effect of capillary pressure. The authors start with the one-dimensional displacement equation (which is nonlinear in the derivative) and, by a change of variable, transform this equation to a semi-linear partial differential equation. This equation is then solved by a finite-difference method on a high-speed digital computer. Fayers and Sheldon5 obtained the solution of the one-dimensional displacement equation by directly replacing the differential equation by a finite-difference equation. The effects of capillary pressure and gravity were in- cluded in their solution. Here, since the movement of the foot of the saturation front is governed by a separate equation, the elapsed time in attaining a particular saturation profile cannot be obtained. The results of these two papers indicate that the inclusion of capillary forces eliminates the triple-valued Buckley-Leverett saturation profiles. In the present paper, the one-dimensional displacement equation for a homogeneous permeable medium, including the effects of capillary and gravity forces, is solved. The method of solution resembles that described in the paper by Douglas, et al, since it involves a similar transformation of variable. However, it extends their work in that the effect of gravity is included and, in addition, pressure profiles may be calculated. Also, the functions of saturation [kro(S), krw(S) and Pc (S) ] required are entered in tabular form rather than as low-order polynomials. This simplifies data preparation and permits the use of a greater range of function types. Unlike the method of Fayers and Sheldon, the corresponding elapsed time required for the development of each saturation profile is calculated and, also, saturation profiles may be calculated after breakthrough. THEORETICAL CONSIDERATIONS The dimensionless form of the one-dimensional displacement equation for a homogeneous porous medium as obtained from Darcy's law and material balance relations can be written as follows.

By A. S. Argon, G. East

From their study of the anisotropy of grain boundary mobility in aluminum, the authors conclude that tilt boundaries have a higher mobility than twist boundaries because the atomic misfit at the pure-twist boundary is relatively small compared to the misfit at a tilt boundary for a given amount of misorientation. If this is true, then one would expect a twist boundary to have a lower grain boundary energy than the corresponding tilt boundary. Fig. 6, taken from the work of Gjostein and Rhines,10 shows that this is indeed the case for [001]-cu tilt and twist boundaries in the high-angle region, thus lending support to the authors' conclusion.

Jan 1, 1968

By P. R. Hanes

A description of the methods used in driving two tunnels, 2 miles long each, one a 9-ft. and the other a 19-ft. diameter section, for the Owyhee Irrigation Project, Oregon. One heading of the smaller tunnel was driven 1315 ft. in 73 shifts in one month and 10,966 ft. of this section completed in ll½ months using two shifts for eight months and three shifts the rest of the time. This is a good illustration of the proper use of a mechanical shovel and the importance of careful selection of supplernentary equipment to secure best results. Large cars, speedier and heavier locomotives, 36-in. gage track of 45-lb. rail, and a good switching method increased actual shoveling time and cut down muck removal period about 45 minutes from average. The larger tunnel, after trying out standard electric revolving shovels of both the rail mounting and caterpillar tread types, was excavated with a mechanical mucker. This is the first time that a tunnel of so large a section has been handled this way. This record work was accomplished without drill carriages.

Jan 1, 1934

By Richards R. Vandervoot

T HE creep behavior of many polycrystalline metals at moderate stresses can be described by the empirical relationship: where Em is the minimum creep rate, A is a constant, a is the applied stress, E is the average elastic modulus at the test temperature, and D is the self-diffusion coefficient.&apos; This equation is generally applicable for strain rates of less than around 10-5 per sec and temperatures greater than about one-half the melting point in absolute units. Under these conditions atomic mobility plays an important role in the deformation process, and steady-state creep occurs when a dynamic equilibrium is reached between the generation and recovery of dislocation substructure. Although several theoretical mechanisms have been proposed to explain the creep of polycrystalline solids,2"4 the dislocation climb model2 is in accord with most experimental observations. The majority of creep data used to develop Eq. [1] came from metals with either the fcc or hcp crystal structures. However, on the basis of results for a and 7 iron as well as those for a and a thallium, Sherby concluded that the high-temperature deformation behavior of close-packed metals and bcc metals is probably the same.&apos; The greater creep resistance of fcc and hcp metals and alloys on a relative temperature scale was attributed to lower diffusivities in the close-packed structures. To further compare the creep properties of fcc, hcp, and bcc metals, creep data for all six bcc refractory metals were analyzed according to Eq. [I]. The results are shown in Fig. 1. The sources of information for the quantities used to prepare this figure are listed in Table I, except for high-temperature elastic moduli. The latter data were obtained from Refs. 28 and 29. The dashed lines in the figure represent the range and breadth of data analyzed by Sherby for fcc and hcp metals. In general, the deformation behavior of all of the refractory metals, ex- cept possibly that of tungsten, can be represented by Eq. [1]. This correlation is strong evidence of the similarity that exists between creep of pure close-packed metals and creep of pure bcc metals. At (Em/D) < 108, the results of Flagella and Tarr on tungsten (W-1 in Fig. 1) agree with the five-power stress law, while those of Green (W-5 in Fig. 1) show a seven-power stress dependence. Where (Em/D) > 108, the stress exponents for other data on tungsten were in the range 10 to 15. It is possible that the creep rate dependence on stress in this region is not a power law but exponential (i.e., Em - eßo). However, it was not feasible to differentiate between these two cases because of the steep slope and scatter in the data. Note the inflection point in the curve for the data of Flagella and Tarr (W-1 in Fig. 1). The slope of the line changes from 5 to around 10 at Em/D = 108. The breakdown of the fifty-power stress law at high stresses is not uncommon in other metals, and this phenomenon may result from nonequilibrium conditions in the material such as excess lattice vacancies produced by rapid straining.30 The mechanical strength of a polycrystalline metal is related to its microstructure. Attempts to establish the influence of grain size on the creep rate of metals and alloys have led to a wide variety of results. For example, the following effects have been observed: creep rate decreases as grain size increases;31&apos;32 creep rate decreases as grain size decreases;&apos;,33 creep rate is a minimum at some critical grain size and increases with either an increase or decrease in

Jan 1, 1969

By H. R. Hanley, Charles Y. Clayton

One of the most important contributions to the art of electrolytic zinc production has been the aluminum cathode. This has been used in all major production since its commercial development in 1916. The literature is replete with important contributions, some of which may have been replaced by better ones, but thus far there appears no other metal to take the place of aluminum as cathode material. Credit for this innovation goes to Sherard Cowper Coles, of England. When experimenting on the extraction of zinc from Broken Hill ore at Hayle, Cornwall, in 1893, he introduced the aluminum cathode, and in 1895 obtained British Patent No. 20073. The reason for this dominant position of aluminum as cathode material in zinc sulphate electrolytes is its unique surface, to which electro-deposited metals usually do not tightly adhere. The metal must, be of high purity for best results. It is possible to develop a starting-sheet method by which thin electro-deposited sheets of cathode zinc are made and stripped from a smooth aluminum plate. Such thin sheets of cathode zinc may be used as are the copper sheets in standard electrolytic copper-refinery practice. However, complications arise because of extreme warping of the zinc starting sheet after a few hours of deposition, and thus special arrangements must be made to compensate for this abnormality. Reasons advanced for the ease with which deposits may be stripped from the aluminum surface are: (1) presence of a permanent oxide coating on the metal, (2) failure of aluminum to alloy with the deposit, (3) differences in coefficient of expansion, (4) high position of aluminum in the electromotive scries of metals. Of these reasons for nonadherence, which may have some application in general deposition, probably the oxide coating has the greatest bearing on the subject of zinc deposition. Adherence of zinc deposits has occasionally had serious effect on tonnage and production costs. Opinions have differed as to the specific

Jan 1, 1943

By H. R. Hanley, Charles Y. Clayton

One of the most important contributions to the art of electrolytic zinc production has been the aluminum cathode. This has been used in all major production since its commercial development in 1916. The literature is replete with important contributions, some of which may have been replaced by better ones, but thus far there appears no other metal to take the place of aluminum as cathode material. Credit for this innovation goes to Sherard Cowper Coles, of England. When experimenting on the extraction of zinc from Broken Hill ore at Hayle, Cornwall, in 1893, he introduced the aluminum cathode, and in 1895 obtained British Patent No. 20073. The reason for this dominant position of aluminum as cathode material in zinc sulphate electrolytes is its unique surface, to which electro-deposited metals usually do not tightly adhere. The metal must, be of high purity for best results. It is possible to develop a starting-sheet method by which thin electro-deposited sheets of cathode zinc are made and stripped from a smooth aluminum plate. Such thin sheets of cathode zinc may be used as are the copper sheets in standard electrolytic copper-refinery practice. However, complications arise because of extreme warping of the zinc starting sheet after a few hours of deposition, and thus special arrangements must be made to compensate for this abnormality. Reasons advanced for the ease with which deposits may be stripped from the aluminum surface are: (1) presence of a permanent oxide coating on the metal, (2) failure of aluminum to alloy with the deposit, (3) differences in coefficient of expansion, (4) high position of aluminum in the electromotive scries of metals. Of these reasons for nonadherence, which may have some application in general deposition, probably the oxide coating has the greatest bearing on the subject of zinc deposition. Adherence of zinc deposits has occasionally had serious effect on tonnage and production costs. Opinions have differed as to the specific

Jan 1, 1943

By H. R. Hanley, C. Y. Clayton

One of the most important contributions to the art of electrolytic zinc production has been the aluminum cathode. This has been used in all major production since its commercial developmerit in 1916. The literature is replete with important contributions, some of which may have been replaced by better ones, but thus far there appears no other metal to take the place of aluminum as cathode material. Credit for this innovation goes to Sherard Cowper Coles, of England. When experimenting on the extraction of zinc from Broken Hill ore at Hayle, Cornwall, in 1893, he introduced the aluminum cathode, and in 1895 obtained . British Patent No. 20073. The reason for this dominant position of aluminum as cathode material in zinc sulphate electrolytes is its unique surface, to which electro-deposited metals usually do not tightly adhere. The metal must be of high purity for best results. It is possible to develop a starting-sheet method by which thin electro-deposited sheets of cathode zinc are made and stripped from a smooth aluminum plate. Such thin sheets of cathode zinc may be used as are the copper sheets in standard electrolytic copper-refinery practice. However, complications arise because of extreme warping of the zinc starting sheet after a few hours of deposition, and thus special arrangements must be made to compensate for this abnormality. Reasons advanced for the ease with which deposits may be stripped from the aluminum surface are: (1) presence of a permanent oxide coating on the metal, (2) failure of aluminum to alloy with the deposit, (3) differences in coefficient of expansion, (4) high position of aluminum in the electromotive series of metals. Of these reasons for nonadherence, which may have some application in general deposition, probably the oxide coating has the greatest bearing on the subject of zinc deposition. Adherence of zinc deposits has occasionally had serious effect on tonnage and production costs. Opinions have differed as to the specific

Jan 1, 1944

By Albert F. J. Bordeaux

INTRODUCTION. THE following general survey of the character and present condition of the silver-mines of Mexico, though not offered as a detailed treatise, has been prepared with care, is believed to he generally up-to-date, and is offered as a summary which may be found useful by mining engineers. Mexico has ranked for several centuries first among the silver-producing countries. It is now second as copper-producer, and seventh as gold-producer, with a fast-increasing output every year. The total amount of capital invested in its mining- and smelting-works is more than $250,000,000, while the yearly metallic production is $160,000,000. There are more than 20,000 recorded mining properties. The silver-mines of Mexico represent deposits of three principal classes: (1) veins and stock-works in eruptive rocks; (2) fissure-veins crossing the crystalline schists, granite, diorite, etc. ; and (3) veins and replacement-deposits in limestone. The true fissure-veins in some districts contain (in value) more gold than silver. In other deposits, the silver is decreasing in depth, leaving galena and zinc-blende as the principal ores.

Jan 9, 1908

By C. W. Spencer, J. Singer

A PARTIAL phase diagram for the As-Te system is given in Hansen.&apos; The only compound reported is As2Te3, melting at 362°C. Stoichiometric quantities of reagent-grade elements were reacted in evacuated quartz and directionally cooled. The resulting ingot consisted of very thin threadlike crystals from which only very small single-crystal fragments were isolated. A powder diffraction diagram disclosed nonisomorphism with the analogous V-VI compounds insofar as these have been reported; Sb2S3, As2S3, Bi,S,, and Bi2Te3 data in the ASTM index of powder patterns, together with the single-crystal data on Sb2Se3,2 were used for the com- parison with the observed spacings. Single-crystal data confirmed the uniqueness of the As2Te3 structure. Single-crystal Weissenberg diagrams have so far yielded the following data: As2Te3 is monoclinic, space group C-m (OkO data still lacking), a = 14.4A, b = 4.05A, C = 9.92A, ß = 97". The cell volume is about 5802. The set of isomorphous ortho-rhombic cells of Sb2Se3, Sb2S3, and Bi2S, are apparently related to As,Te, in having one lattice constant close to 4.0 and with cell volumes as large as 540A8. Assuming Z = 4 for As2Te3 also, the density is calculated as 6.1 which agrees well with a roughly determined value of 6.0. A complete structure analysis is under way.

Jan 1, 1956

By ROBERT. RICHARDS

I. INTRODUCTION The object of this paper is to enlarge the field of settling velocities treated by me in my former papers, Close Sizing Before Jigging, and Sorting Before Sizing.&apos; There seemed need of work both on coarser and on finer sizes. Messrs. A. Sidney Warren and M. L. Nagel undertook the investigation for the coarser sizes, from 12.85 mm. down to 2.05 mm. diameter. Their work, because of the closer spacing and because of the increased number of observations and consequent stronger averages, called for a revision of the former work. Messrs. G., A. Barnaby and Ralph Hayden undertook this part of the work, from 2.49 mm. down to 0.28 mm., which is near the limit of sifting. Their work covers the ground much more minutely and comprehensively than the former papers. There remained to be covered the portion of the field too fine for investigation with the sieves. This part, covering the range of grains from 0.48 to 0.03 mm., was undertaken by Mr. E. S. Bardwell. For it he used the elutriation method. II. THE FIRST, OR COARSEST, SECTION OF THE FIELD. The first desideratum in this investigation was a series of sieves for sizing the sands preparatory to making the tests. It became necessary, therefore, to decide on a sieve-scale for this purpose. A sieve-scale is a series of sieves in which the dimensions of the holes of the successive members form a series increasing by a. definite ratio. There are three natural sieve-scales : 1, progressing by doubling the width of the hole for each suc-

May 1, 1907

By D. Cubicciotti

IT has long been known that some metals are capable of being dispersed or dissolved in certain of their fused salts.&apos; Davy&apos; and Bunsen³ were among the first to observe that in some fused salt electrolyses, a highly colored, strongly reducing salt phase appeared in the neighborhood of the cathode. Later workers found that the current efficiency of the electrolysis was markedly reduced when such a phase appeared. It was also found that the strongly reducing salt could be made by melting the metal and normal salt together. Chemical analysis showed that in such salts the metal ion to anion ratio was always larger than in the normal salt. From such observations arose two different explanations of the nature of metal in salt solutions. When a solution of this type is quenched, it is possible to find small globules of metal in the salt. From this and other observations, Lorenz&apos; and co-workers assumed the metal in salt solution to be a colloidal dispersion of metal in the fused salt and called it "metallnebel" or metal fog formation. They made a number of experiments to substantiate this point of view. Another school felt that when the metal dissolved it reduced the salt partially to a mixture or solution of normal salt and subsalt. Both of these ideas could explain the strong reducing character of the salt formed and the low current efficiency of the electrolysis. If either a metal colloid or a subsalt were formed at the cathode and diffused to the anode, it would be oxidized to the normal salt. Thus a cyclic process of oxidation and reduction could be set up conducting the current without giving rise to a net change in the system. These facts led the author to investigate some of the properties of metal in salt solutions with the hope of elucidating their nature further. Among the metal-salt systems that form metal in salt solutions most markedly are the alkaline earth metal-halide systems and cerium, bismuth, and cadmium halides. Other systems of halides, oxides and sulphides form such solutions to a lesser degree. The first work undertaken was a study of the temperature-composition diagrams of some of the systems." From such diagrams it would be possible to distinguish between a subhalide formation or a colloid. A subhalide should give rise to characteristic changes in the phase diagram, while a colloidal dispersion of metal in salt would not alter the freezing point of the salt. The results obtained on a number of alkaline earth metal-halide systems were all quite similar. Fig. 1 shows the barium-barium chloride system. The other

Jan 1, 1954

By Thomas M. Barczak

This paper describes a computerized simulation system developed by KETRON, Inc., in cooperation with the US Bureau of Mines. The system is designed for use by mine managers and engineers rather than computer specialists and allows the novice user to arbitrarily create room-and-pillar mine plans, with the computer illustrating the simulation of face activities on a video screen. Extensive visibility of the simulation is provided by visual display of the machine elements and their movement in the section to accommodate the extraction, roof control, place changing, and haulage operations. Performance statistics are also generated to analyze the operations. Both conventional and continuous mining methods can be simulated. In addition to simulating arbitrary scenarios, the system can also be used to display actual time-studied operations and maintain a file of these activities. Practical applications and case studies are provided in the paper to demonstrate the usefulness of the system. The system is designed to operate on a desk-top mini computer and is currently installed on a Hewlett-Packard 9854B system with 450 K bytes of memory.

Jan 1, 1983

By W. Hurst

The authors of this paper, in substituting values in a material balance equation associated with a gas reserve and a water drive, cannot find sustainment of what the gas in place should be; therefore, their conclusion is that this type of problem dealing with gas reservoirs is insoluble. They have introduced the word, "cybernetics," based on the work of Norbert Wiener, that further extends this line of reasoning, namely, to the effect that the system is a "black box", and that the gas reservoir and aquifer can take on infinite aspects &apos;based upon their past performance, to quote the authors. The inference is that this black box is an unknown. which permits in computer programming to subscribe as many variables as possible to observe by adjustment of one to another those combinations of conditions that fit field behavior. This may satisfy those in this discipline whose dedication is to programming, but to the others this is a comparison to the rationalization of the combinational results of the throwing of dice—a probability procedure. In reservoir engineering we are more direct. We learn from the examination of individual we&apos;ll and field data exactly what is in this black box. I now come to the impasse that has confronted these authors in their machine calculations. In this I have reproduced from their own production data (Tables 1 and 2 of their paper) pressure vs cumulative gas produced. shown as Figs. D-1 through D-5. A perusal of any of these five plots, for the corresponding fields in the Po Valley, shows the straight-line relation of pressure vs gas produced, evidencing pressure depletion. The point I make is that in their fundamental production data, there is no variance from a straight line that can support a water drive.

By Henry S. Rawdon

The relation between the course, or path, of the fracture of metals and alloys, produced in service or as a result of certain laboratory tests, and the crystalline units of which such materials are composed is of utmost importance. The fracture of normal material is, in general, intracrystalline, i.e., it consists of a break across the grains rather than of a separation between them. An interorystalline fracture indicates either that the metal is of very inferior quality or that the break occurred under very unusual conditions, e.g., at a very high temperature. The usual mechanical tests, when applied to metals of the type that breaks with an intercrystalline fracture, merely measure the coherence of adjacent grains for one another and reveal little as to the real properties of the metal itself. Even such a soft plastic substance as lead, under suitable conditions, may be rendered so weak and brittle that the metal can be easily crumbled into powder by the fingers although the constituent grains have lost none of the intrinsic properties of lead. Various erroneous explanations of this behavior of lead have appeared in the scientific literature, the change being described usually as an allotropic one. The importance, in an industrial sense, of a proper explanation of this type of the corrosion of lead justifies the description of the type of metal deterioration that follows. Corroded Lead Sheathing In Figs. 1 and 2 are shown two typical specimens of corroded lead sheathing selected from materials submitted to the Bureau of Standards for examination. Fig; 1 shows a section of the sheathing of an aerial cable; Fig. 2, that of the lead covering of a subterranean feeder-line of an electric light system. In this case the deterioration had proceeded to a much great&apos;er extent than in the case shown in Fig. 1 so that certain portions of the metal could easily be crumbled into a coarse gray powder by the fingers. This was particularly true of those portions of the sheathing

Jan 1, 1921