Search Documents

By Nicholas J. Grant, Bill C. Giessen

The phase diagram Ta-Ni has been treated repeatedly; investigations up to 1958 are summed up in Ref. 1. Since then, an equilibrium diagram has been presented by Kornilov and Pylaeva.2 They found the following intermediate phases: Ta2N; (CuA12 type),3 "TaNi" (p phase, Mo8Co7 type), TaNiz, and TaNi3 (Ticus type).5 Of these, the crystal structure of TaNin remained unknown, and no further literature reference was found. According to Kornilov and pylaeva,&apos; TaNil melts peri-tectically at 1420°C. A 5-g alloy of Ta + 66.7 at. pct Ni was prepared by inert-gas arc melting using 99.95 pct Ta rod (NRC-MG) and 99.9 pct Ni shot (Fisher). The weight loss after three melts was <2 mg; a microscopically homogeneous ingot resulted. As shown in Ref. 6, no oxygen or impurity pickup needed to be considered under these conditions. Specimens were annealed for 15 hr at 1350°C, 15 hr at 1205oC, and 15 hr at 875°C with subsequent powdering and stress relief for 10 min at 1350°C, 15 min at 1205oC, and 1 hr at 875oC, respectively. Micrographs and X-ray analysis (114.6 mm Norelco camera, filtered CuK, radiation) showed homogeneous one-phase alloys in the as-cast state and at all three temperatures, all having the same powder pattern except for broad lines in the as-cast state. From this it is concluded that either TaNi, melts congruently or its melting behavior is a transition between the eutectic and peritectic cases. Since it was found that very slight surface contamination on stress relieving can considerably alter the structure of similar phases (e.g.,TaPt3),7 patterns before and after stress relief were also compared; they were identical except for line broadening in the non-stressrelieved condition, and two faint impurity lines in the stress-relieved samples. The powder pattern is presented in Table I. All lines were accounted for by indexing with a tetragonal lattice, 0Yh- I4/mmm , with a, = 3.154 ± 0.001A, co = 7.905 * 0.002i and c/a = 2.506. The atomic positions are: 1000; 1/2, 1/2, 1/2] + 2Ta(a): 000; + 4Ni(e): *(002); z = 0.333 * 0.002 This proves TaNi2 to be a representative of the MoSiz (Cllb) type. The variable parameter was determined by grouping the visually estimated intensi- ties according to their 2 indices, plotting their F values, and varying z for best fit, which was obtained at z = 0.333= 1/3. Since absorption was not considered, only the relative intensities with similar 28 can be expected to agree. The interatomic distances are presented in Table 11; the standard error is *o.o2A, resulting chiefly from the uncertainty in z. These distances indicate a coordination number 10 for both kinds of atoms and show that the pseudohexagonal layers along (110) are rather un-distorted. The mean atomic volume of 13.1A3 is close to the Vegard&apos;s law value of 13.3A3, showing

Jan 1, 1964

By W. M. Weigel

Economic deposits of barite occur in Missouri in two main districts. The most important, the Southeastern or Washington County district, is in the southeastern part of the state, mostly in Washington County with a small extension into the northeastern part of St. Francois County. Roughly, it embraces nine townships or about 200,000 acres and accounts for from 80 to 90 per cent. of the state production. The Central district, is in the central part of the state, includes most of Morgan and Miller counties, and parts of Camden; Benton, Moniteau and Cole counties. The area embraced is much larger than the Washington County district, but the deposits are more infrequent. The location and general area covered by the two districts is shown in Fig. 1. There is another small area in southern Franklin County but so far its production has been of small consequence. It might be considered as a northward extension of the Washington County field. An, area in the central part of Hickory County has also produced a small amount. The outline of the districts as shown indicates the general area in which deposits have been found. The total area covered by deposits of barite is only a small part of this, as, in the Central district especially, there may be miles of supposedly barren areas between ore-bearing areas of an acre or two in extent. The date when barite was first mined in Missouri cannot be definit stated, but the industry probably dates back to about 1860. The occurrence of barite was known long before this, as it was encountered in the lead mines in Washington County and mentioned by several earlier writers." Missouri is reported as producing 8000 tons in 1882 so it is evident the industry was well under way in the seventies in order to have arrived at this substantial production. By 1893 Missouri production had increased so that it ranked with that of Virginia, then the largest producer it increased until in 1914 Missouri accounted for about 65 per cent. of the total United States output.

Jan 1, 1929

By J. M. Bugbee

The engineer and the conservationist agree that effective water drive is the desirable reservoir production mechanism. Water drive may result either from the expansion of edge water, the reservoir water bordering an oil pool, or from the artesian flow of edge water from the outcrop. Thus, the extent of the reservoir has an important bearing upon both the rate and the ultimate quantity of water influx to an oil pool. Lens-type reservoirs are generally recognizable, but the complete structure of the more important domal types, having possible limitations from crestal and synclinal faulting, is not well understood. The delineation from cores, electrical logs and exploitation phenomena of the crestal portions of reservoirs is increasingly exact. This paper suggests that inference from these factual pictures, combined with the scattered well and geophysical data of the synclines and with consideration of the dynamics of structural formation, may be applied to solving the complete geologic structure. Since faulting on the domes and in the synclines may effectively seal and thus limit the size of a reservoir and bar additional water influx, consideration of geologic structure and its possible effects is essential to complete analysis and prediction of reservoir performance. Introduction Implicit in reservoir studies is the fact that the oil must be displaced from the reservoir rock by some other fluid, either gas or water, and this understanding yields the terms descriptive of the major reservoir production mechanisms, gas expansion and water drive&apos; Three recent papers1-2-3 make clear the economic and conservation preeminence of Water drive as a production mechanism; in fact, the title of the latest of these is " Production under Effective Water Drive as a Standard for Conservation Practice." There appears to be an assumption at times among analysts that the effectiveness of a water drive is solely dependent on the rate of oil production; that is, if water drive appears to be insufficient or lacking, a lower oil-recovery rate would increase or reveal it. This assumption might result from the fact that the analysis has been wholly developed during the period of production curtailment; that is, since 1929. The writer takes it that the recurrent phrase in De Golyer&apos;s paper,3 "some degree of water drive," is related to this assumption. In California, an extraordinary phrase, "inactive water drive," is rather common and the connotation of uncertainty regarding our knowledge of reservoir performance is evident. Wyckoff2 speaks of the type of reservoir and performance as follows: "In general, reservoirs may be any one or a combination of domal, faulted, lenticular, or stratigraphic traps. Insofar as the dynamic performance of such reservoirs is concerned, the particular type merely determines whether regional flow is symmetrical as in a uniformly developed domal or lenticular type, or one-sided as in many stratigraphic or faulted traps." But whether the flow is

Jan 1, 1943

By J. M. Bugbee

The engineer and the conservationist agree that effective water drive is the desirable reservoir production mechanism. Water drive may result either from the expansion of edge water, the reservoir water bordering an oil pool, or from the artesian flow of edge water from the outcrop. Thus, the extent of the reservoir has an important bearing upon both the rate and the ultimate quantity of water influx to an oil pool. Lens-type reservoirs are generally recognizable, but the complete structure of the more important domal types, having possible limitations from crestal and synclinal faulting, is not well understood. The delineation from cores, electrical logs and exploitation phenomena of the crestal portions of reservoirs is increasingly exact. This paper suggests that inference from these factual pictures, combined with the scattered well and geophysical data of the synclines and with consideration of the dynamics of structural formation, may be applied to solving the complete geologic structure. Since faulting on the domes and in the synclines may effectively seal and thus limit the size of a reservoir and bar additional water influx, consideration of geologic structure and its possible effects is essential to complete analysis and prediction of reservoir performance. Introduction Implicit in reservoir studies is the fact that the oil must be displaced from the reservoir rock by some other fluid, either gas or water, and this understanding yields the terms descriptive of the major reservoir production mechanisms, gas expansion and water drive&apos; Three recent papers1-2-3 make clear the economic and conservation preeminence of Water drive as a production mechanism; in fact, the title of the latest of these is " Production under Effective Water Drive as a Standard for Conservation Practice." There appears to be an assumption at times among analysts that the effectiveness of a water drive is solely dependent on the rate of oil production; that is, if water drive appears to be insufficient or lacking, a lower oil-recovery rate would increase or reveal it. This assumption might result from the fact that the analysis has been wholly developed during the period of production curtailment; that is, since 1929. The writer takes it that the recurrent phrase in De Golyer&apos;s paper,3 "some degree of water drive," is related to this assumption. In California, an extraordinary phrase, "inactive water drive," is rather common and the connotation of uncertainty regarding our knowledge of reservoir performance is evident. Wyckoff2 speaks of the type of reservoir and performance as follows: "In general, reservoirs may be any one or a combination of domal, faulted, lenticular, or stratigraphic traps. Insofar as the dynamic performance of such reservoirs is concerned, the particular type merely determines whether regional flow is symmetrical as in a uniformly developed domal or lenticular type, or one-sided as in many stratigraphic or faulted traps." But whether the flow is

Jan 1, 1943

By L. V. Wade

Abstract-US Bureau of Mines efforts under longwall research programs to develop the capability to predict support requirements for longwall/shortwall support systems are discussed. Ground control studies are being conducted in conjunction with several longwall/shortwall demonstration projects. Geologic, support performance, and strata behavior are being documented on these projects. A hypothesis is presented for the prediction of support requirements.

Jan 11, 1978

By Fred P. Dewey

In my paper on the porosity and specific gravity of coke, read at the Roanoke meeting, June, 1883, and published in this volnme, an analysis by Dr. henry Froehling is reported (p. 10 of the preliminary edition of the paper, or p. 120 of this volume), as showing the composition of Fire Creek coke. This analysis WaS of coke made in beehive ovens at Low Moor, Va., from New River coal. Dr. Froehlng&apos;s analysis of the Fire Creek coke was as follows: Moisture..........0.260 Volatile matter.........0.260 Fixed carbon .........92.377 Ash 1....6.750 Sulphur..........0.535 Phosphorus.........0.0146 Both analyses are reported side by side in The Erginias for 1883, p. 99. By an error in copying, the Low Moor analysis was trans-

Jan 1, 1884

By Geoffrey Gilbert

THE Montana Phosphate Products Co., subsidiary of the Consolidated Mining and Smelting Company of Canada, operates three phosphate properties north and northeast of Garrison, Powell County, Mont. Production of all three is from the same phosphate bed, a 3 to 4-ft. member of the Phosphoria formation, whose outcrop is traceable across the mountains of the Garnet Range in a series of southeasterly pitching folds. Because of topographical differences and of variations in the attitude of the bed, each property has its own mining methods and problems. Most of the phosphate rock produced since I930 has been shipped to the plant of the Consolidated Mining and Smelting Co. at Trail, B.C., where it is treated with sulphuric acid for conversion to phosphoric acid, which in turn is used to produce various fertilizers. HISTORY The occurrence of rock phosphate in Montana has been known. since 1910, and the Garrison area was mapped by the United States Geological Survey in 1913In the nineteen twenties William Anderson, owner of a ranch 8 miles north of Garrison, discovered phosphate on his land, and the Montana Phosphate Co., which later became the Montana Phosphate Products Co., was formed to work the deposit. Montana Phosphate Products Co. later obtained United States leases on two adjoining parcels of ground, and this combined property, known as the Anderson mine, has been the main source of Consolidated&apos;s phosphate rock. The mine now includes an adjoining parcel leased from Anaconda and mined from the Anderson workings. In 1940, the Graveley mine, a small privately owned property 6 miles east of the Anderson, was leased from the owner by Montana Phosphate Products Co., and a U. S. lease held by Graveley on some adjoining ground was subleased. In 1943 the Luke mine, on the Mineral Hill property, 1 ¾ miles south-southwest of the Graveley, a U. S. lease, which previously had produced a few thousand tons, was optioned from the lessees by Montana Phosphate Products Co., and is now being developed. At both these mines the rock is appreciably higher grade than at the Anderson mine. GEOLOGY The Phosphoria formation is the Permian member of an extensive sequence of Paleozoic and Mesozoic rocks. It is underlain by Pennsylvanian (Quadrant) quartzite and Mississippian limestone, and overlain without any marked unconformity by Jurassic (Ellis) shale and Cretaceous shale and sandstone. In the Garrison area, the Phosphoria itself consists mainly of about 50 ft. Of gray to yellow chert. Immediately below the chert is the phosphate, usually 3 to 4 ft. thick. Below the phosphate occur a few

Jan 1, 1945

By Geoffrey Gilbert

The Montana Phosphate Products Co., subsidiary of the Consolidated Mining and Smelting Company of Canada, operates three phosphate properties north and northeast of Garrison, Powell County, Mont. Production of all three is from the same phosphate bed, a 3 to 4-ft. member of the Phosphoria formation, whose outcrop is traceable across the mountains of the Garnet Range in a series of southeasterly pitching folds. Because of topographical differences and of variations in the attitude of the bed, each property has its own mining methods and problems. Most of the phosphate rock produced since 1930 has been shipped to the plant of the Consolidated Mining and Smelting Co. at Trail, B.C., where it is treated with sulphuric acid for conversion to phosphoric acid, which in turn is used to produce various fertilizers. History The occurrence of rock phosphate in Montana has been known since 1910, and the Garrison area was mapped by the United States Geological Survey in 1913. In the nineteen twenties William Anderson, owner of a ranch 8 miles north of Garrison, discovered phosphate on his land, and the Montana Phosphate Co., which later became the Montana Phosphate Products Co., was formed to work the deposit. Montana Phosphate Products Co. later obtained United States leases on two adjoining parcels of ground, and this combined property, known as the Anderson mine, has been the main source of Con-solidated&apos;s phosphate rock. The mine now includes an adjoining parcel leased from Anaconda and mined from the Anderson workings. In 1940, the Graveley mine, a small privately owned property 6 miles east of the Anderson, was leased from the owner by Montana Phosphate Products Co., and a U. S. lease held by Graveley on some adjoining ground was subleased. In 1943 the Luke mine, on the Mineral Hill property, 1 3/4 miles south-southwest of the Graveley, a U. S. lease, which previously had produced a few thousand tons, was optioned from the lessees by Montana Phosphate Products Co., and is now being developed. At both these mines the rock is appreciably higher grade than at the Anderson mine. Geology The Phosphoria formation is the Permian member of an extensive sequence of Paleozoic and Mesozoic rocks. It is underlain by Pennsylvanian (Quadrant) quartzite and Mississippian limestone, and overlain without any marked unconformity by Jurassic (Ellis) shale and Cretaceous shale and sandstone. In the Garrison area, the Phosphoria itself consists mainly of about 50 ft. of gray to yellow chert. Immediately below the chert is the phosphate, usually 3 to 4 ft. thick. Below the phosphate occur a few

Jan 1, 1948

By Geoffrey Gilbert

The Montana Phosphate Products Co., subsidiary of the Consolidated Mining and Smelting Company of Canada, operates three phosphate properties north and northeast of Garrison, Powell County, Mont. Production of all three is from the same phosphate bed, a 3 to 4-ft. member of the Phosphoria formation, whose outcrop is traceable across the mountains of the Garnet Range in a series of southeasterly pitching folds. Because of topographical differences and of variations in the attitude of the bed, each property has its own mining methods and problems. Most of the phosphate rock produced since 1930 has been shipped to the plant of the Consolidated Mining and Smelting Co. at Trail, B.C., where it is treated with sulphuric acid for conversion to phosphoric acid, which in turn is used to produce various fertilizers. History The occurrence of rock phosphate in Montana has been known since 1910, and the Garrison area was mapped by the United States Geological Survey in 1913. In the nineteen twenties William Anderson, owner of a ranch 8 miles north of Garrison, discovered phosphate on his land, and the Montana Phosphate Co., which later became the Montana Phosphate Products Co., was formed to work the deposit. Montana Phosphate Products Co. later obtained United States leases on two adjoining parcels of ground, and this combined property, known as the Anderson mine, has been the main source of Con-solidated&apos;s phosphate rock. The mine now includes an adjoining parcel leased from Anaconda and mined from the Anderson workings. In 1940, the Graveley mine, a small privately owned property 6 miles east of the Anderson, was leased from the owner by Montana Phosphate Products Co., and a U. S. lease held by Graveley on some adjoining ground was subleased. In 1943 the Luke mine, on the Mineral Hill property, 1 3/4 miles south-southwest of the Graveley, a U. S. lease, which previously had produced a few thousand tons, was optioned from the lessees by Montana Phosphate Products Co., and is now being developed. At both these mines the rock is appreciably higher grade than at the Anderson mine. Geology The Phosphoria formation is the Permian member of an extensive sequence of Paleozoic and Mesozoic rocks. It is underlain by Pennsylvanian (Quadrant) quartzite and Mississippian limestone, and overlain without any marked unconformity by Jurassic (Ellis) shale and Cretaceous shale and sandstone. In the Garrison area, the Phosphoria itself consists mainly of about 50 ft. of gray to yellow chert. Immediately below the chert is the phosphate, usually 3 to 4 ft. thick. Below the phosphate occur a few

Jan 1, 1948

By T. B. Counselman

AFTER several years study, the Universal Atlas Cement Co. decided to rebuild its plant at Leeds, Alabama. The entire old plant, which was to operate during the new construction, was then to be scrapped with the exception of two kilns. The quarry was to be mechanized, new and larger kilns installed, with the most modern type of equipment all through the plant. Raw grinding operations at all of the Universal Atlas plants were dry. However, the dust hazard of this operation and the growing emphasis on occupational diseases made wet grinding attractive. Coal at Leeds is cheap, so that a slightly higher coal practice was unimportant. Power was cheap, so that waste-heat boilers were not desirable. Since new kilns were to be installed, these could be made long enough to make filters unnecessary. Wet raw grinding could be either the old practice of open-circuit compartment mills or closed-circuit grinding in accordance with metal-lurgical practice. The latter saved power and steel wear and saved initial investment. This had been demonstrated in cement plants. Also, the elimination of tramp oversize was a most important advantage. Ease of chemical control was another factor. Blending in the thickener, with elimination of slurry mixers had been found practicable. Therefore, if wet raw grinding were used at all, the advantages were clearly in favor of closed-circuit grinding. Detailed layouts of the most modern possible closed-circuit dry-grinding plant and of a closed-circuit wet-grinding plant were prepared, and careful estimates were made of initial invest-ment and operating costs. Full consideration of all the factors involved resulted in a decision to install wet closed-circuit grinding.

Jan 1, 1939

Jan 1, 1967

Olof Venstrom (communication to the Secretary*):—In order to do justice to a property, once the largest producer of copper in the world, which is now being reopened, with a fair promise of again becoming important, I beg to add a few words in connection with Mr. Souder&apos;s remarks on the El Cobre copper-mines. The El Cobre copper-mines were worked by the old English

Jan 1, 1905

By Ralph H. Sweetser

At the joint session of Blast Furnace and Open Hearth Committees, April 7, 1937, at Birmingham, the subject of the quality of basic open-hearth pig iron was so well presented and discussed from so many different viewpoints that it was the general opinion that progress had been made and that such meetings were conducive to the advancement of the art of making pig iron of the right quality for the open-hearth man to produce the most satisfactory quality of steel. It was agreed that there is a decided differentiation between the chemical analysis of pig iron and the "quality" of pig iron. Paul J. McKim said that open-hearth furnace operators frequently make reference to certain types of iron as "bad iron," "dirty iron," "cold metal," etc., claiming that when using these irons, although they are within specified chemical analysis, it is impossible to produce quality steel. Mr. McKim gave a list of the suggested causes of those "certain types" of bad irons that have a thoroughly respectable analysis but a thoroughly disreputable character. Another open-hearth man, P. A. MacIsaac, of Nova Scotia, said that: The effects of iron that is below standard in analysis or in that mysterious property called quality, are well known to all open-hearth operators. It has been shown that iron of this type results in the production of steels on which the rcjections of finished product run high. What is to be done about it? I would say that the burden of producing high-quality iron should be placed squarely on the shoulders of the blastfurnace man, even as that of making good steel is shouldered by the open-hearth man. It is the purpose of this paper to bring out into the open this "mysterious property called quality"; that is, in those "certain types" of basic pig iron that make it impossible to produce quality steels; and at the same time to point the way for the blast-furnace man to be able to shoulder the burden that Mr. MacIsaac and all other open-hearth men and foundry-men have placed upon him. Silicon, sulphur, phosphorus and manganese are not the guilty elements because these are known, specified and usually kept within the

Jan 1, 1938

By Ralph H. Sweetser

At the joint session of Blast Furnace and Open Hearth Committees, April 7, 1937, at Birmingham, the subject of the quality of basic open-hearth pig iron was so well presented and discussed from so many different viewpoints that it was the general opinion that progress had been made and that such meetings were conducive to the advancement of the art of making pig iron of the right quality for the open-hearth man to produce the most satisfactory quality of steel. It was agreed that there is a decided differentiation between the chemical analysis of pig iron and the "quality" of pig iron. Paul J. McKim said that open-hearth furnace operators frequently make reference to certain types of iron as "bad iron," "dirty iron," "cold metal," etc., claiming that when using these irons, although they are within specified chemical analysis, it is impossible to produce quality steel. Mr. McKim gave a list of the suggested causes of those "certain types" of bad irons that have a thoroughly respectable analysis but a thoroughly disreputable character. Another open-hearth man, P. A. MacIsaac, of Nova Scotia, said that: The effects of iron that is below standard in analysis or in that mysterious property called quality, are well known to all open-hearth operators. It has been shown that iron of this type results in the production of steels on which the rcjections of finished product run high. What is to be done about it? I would say that the burden of producing high-quality iron should be placed squarely on the shoulders of the blastfurnace man, even as that of making good steel is shouldered by the open-hearth man. It is the purpose of this paper to bring out into the open this "mysterious property called quality"; that is, in those "certain types" of basic pig iron that make it impossible to produce quality steels; and at the same time to point the way for the blast-furnace man to be able to shoulder the burden that Mr. MacIsaac and all other open-hearth men and foundry-men have placed upon him. Silicon, sulphur, phosphorus and manganese are not the guilty elements because these are known, specified and usually kept within the

Jan 1, 1938

By Peter R. Morris, Alan J. Heckler

THREE angles are required to specify the orientation of a crystallite with respect to a physical reference frame. The distribution of crystallite orientations in a polycrystal is thus a function of three angular variables. The most widely used experimental techniques for studying orientation in polycrystals lead directly to the pole figure representation, i.e., the distribution of the poles of certain crystallographic planes in terms of two angular variables. In recent years1-5 methods have been developed which permit determination of the (three-angle) crystallite orientation distribution from several (two-angle) pole figure distributions. In this work Roe&apos;s method has been applied to the study of orientation in hcp materials. The method is illustrated for commercial purity titanium sheet (Ti-70) which was cold rolled (65 pct reduction), annealed at 1450°F for 3 min, and air cooled. The grain shape was observed to be equiaxed after this treatment. EFFECTS OF PHYSICAL, CRYSTALLOGRAPHIC SYMMETRY In Roe&apos;s method the crystallite orientation distribution, w(?,?,F), is expanded in a series of generalized spherical harmonics 11(?,?,F) = E E E W^Zirmtye-tote-in* [l] 1=o ,,,=-I ,,=-I where { = cos 8. The set of Euler angles employed here is illustrated in Fig. 1. The axis for each rotation is denoted by a double arrowhead. The positive sense of each rotation is that of a right-handed screw advancing in the direction of the double arrowhead. The X, Y, and Z directions correspond to the rolling direction, cross direction, and normal direction, respectively. In the initial orientation (10.O), (12.O), and (00 . 1) planes are perpendicular to the X, Y, and Z directions, respectively. The IC/ rotation about the Z axis is carried out first by rotating X into X&apos;, Y into Y&apos;, and leaving 2 unchanged, i.e., Z&apos; = Z. The 8 rotation about the Y&apos; axis is carried out second by rotating X&apos; into X", 2&apos; into Z", and leaving Y&apos; unchanged, i.e., Y" = Y&apos;. The I$ rotation about the Z" axis is carried out last by rotating X" into X"&apos;, Y into Y"&apos;, and leaving 2" unchanged, i.e., 2"&apos; = 2". Any specified orientation of the X&apos;", Y&apos;", and Z&apos;" crystal-fixed axis system relative to the X. Y, and Z physical axes (rolling direction, transverse direction, and sheet normal direction, respectively) can be obtained by appropriate IC/, 8, and (F rotations. The Zl,, of Eq. [l] are the Jacobi polynomials, augmented by the square root of the weight function. The Zl,, are symmetric in m,n, i.e., Zl,,= Zlnm. For orthotropic physical symmetry and hexagonal crystallographic symmetry, the coefficients, W!,,, of the series are all real, W!mn = Wzfi, = Wlm~ = Wlfi~, 1 and m are even and n is restricted to 6k, where k = ...,-2,-1, 0, 1, 2, .-.. The determination of the Wlmn from pole figure data has been previously described.&apos;~~ The Zl,, may be written in multiple angle form

Jan 1, 1970

Abrahamson. Guy C., (S&apos;43) Univ. of California, Berkeley. Calif. &apos; Abrego, Alfredo, (S&apos;43) Texas College of Mines Metallurgy, El Paso, Texas. Adamec, Lew, (S&apos;42) c/o Braden Copper Co., Ran¬cagua, Chile. Adams, Charles E., (S&apos;42) Box 1527, Stockton, Calif. Adams, John W? (S&apos;42) Asst. Petr. Engr., Vander¬ bilt Dist., Magnolia Pets. Co., Edna. Texas. Adams, Karl S., (S&apos;43) Univ. of New Ha mpshire, Durham; N. H. Adamson, Charles R., (S&apos;41) Univ. of Utah, Salt Lake City, Utah. Aguilar, Ruperto G., (S&apos;43) Texas College of Mines, El Paso,. Texas. Almone, Francis M., (S&apos;41) Univ. of Toronto, Toronto, Ont., Canada. Ainge, Ronald Farra, (S&apos;43) Otago University, Dunedin, New Zealand. Akarun, Cevdet A., (S&apos;44) Pennsylvania State College, State College. Pa.

Jan 1, 1944

International Trade in Nonmetallic Minerals. BY J W FURNESS AND E W PEHRSON (Man &. Met, Sept, 432 2500 words) International trade in nonmetalic minerals (exclusive of fuels) is dominated largely by fertilizer raw materials such as phosphate rock, potash, nitrates, sulphur and pyrites and the miscellaneous group of minerals including asbestos, mica, graphite, fluorspar and china clay Cost of trans¬portation deters any substantial movement of the building materials which usually occur widely in nature and are thus available near consuming centers at relatively low cost This paper, which presents a summary for 1932 of the world production, consumption and principal trade relations of asbestos, china clay, fluorspar, graphite, gypsum, mica, phosphate rock and potash illustrated by world charts, is based on an original study of 15 nonmetallic minerals conducted by the U S Bureau of Mines Practical and Legal Aspects of Mme Financing See METAL MINING Economic Significance of High-grade Concentrates See MILLING AND CONCENTRATION

Jan 1, 1937

By D. J. Carney, C. W. Boquist, E. C. Rudolphy

Effect of variations in sinter feed composition on sinter strength, bulk density, re-ducibility, chemical composition, and microstructure were determined by sintering experimental samples on a production sintering machine. Increasing amounts of roll scale, ore fines, return fines, and blast furnace slag were most beneficial to feed permeability, sinter bulk density, and strength. Burnt lime additions improved feed permeability but were not beneficial to sinter strength or bulk density. Sinter reducibility was adversely affected by all additives. DEVELOPMENT of methods for evaluating sinter quality, which would in some way predict the behavior of the sinter during charging and smelting in the blast furnace, has been given considerable attention in recent years. In a previous investigation at South Works of the United States Steel Corp., standard sinter sampling and testing procedures were developed.1,2 By modifying the sinter sampling device, a method of sintering experimental mix sinter samples upon a production Dwight-Lloyd sintering machine was also developed. This technique afforded a rapid and controlled method of investigating the effects of the various raw materials and additives on sinter quality and was used in this present investigation. Since the beginning of the present study in 1953, the results of numerous sinter investigations have been published, most of which were concerned with production tests of iron ore sinter, both here and abroad. Three groups of investigators reported results of experimental sinter studies that were related to this investigation. Voice et al.3 studied the effects of controlled variables on sinter quality by producing and testing experimental Northants iron ore sinter using an experimental sintering unit. Mor-rissey and Powers&apos; determined the relationship between iron ore sinter quality and the moisture and coke content using a small laboratory sintering system. Burlingame et al.5 studied the effects of "additives" upon iron ore sinter using a laboratory sintering apparatus and laboratory grade raw materials. At South Works, it was considered desirable to study the effects of sinter mix composition and additives upon the quality of a flue dust-base sinter produced on a production sintering unit. Extrapolation of controlled laboratory test data to sintering plant operation lacking such precise control is not altogether satisfactory. Therefore, the present study was conducted in a manner which approximated production conditions as closely as possible. The raw materials used were those commonly encoun- tered in the production of flue dust and flue dust ore-type sinters and these were varied within extremes encountered in this type of sinter production. Experimental Procedure The experimental sinters were produced from 100 lb mixtures of sinter feed. The principal raw materials and additives used, their particle size, and approximate chemical composition are listed in Table I. The mixing of the raw materials was accomplished by means of a miniature single shaft pug mill shown in Fig, 1. The use of the pug mill as a mixer was decidea upon after encountering difficulty in reproducing the mixing and chopping effect of the sinter plant pug mill with other types of available small mixers. The miniature pug mill was constructed, consisting of 31/2x2x1/4 in, blades spaced 3 in. apart along a 3 ft shaft. Preliminary tests were run with this small mixer to establish the proper rotation speed and the required number of passes through the pug mill to thoroughly mix and distribute all the raw materials in a manner approximating the production Pug mill- Although the effects of varying the mosture content were determined in one particular series of tests, the amount of moisture added was changed as the composition of the experimental mix was varied. The aim in making water additions was to achieve a permeability as high as possible for each particular

Jan 1, 1956

By Kefton Teague

The minerals discussed in this section have experienced a gradual, although not spectacular, growth in general. Obvious exceptions are the gradual decreasing use of talc and bentonite as filler materials, partly because of availability and relatively lower sales price of competitive materials. Mineral fillers and filter minerals are used principally in those countries that are heavily industrialized. Except for diatomaceous earth of filter grade, most industrialized countries are reasonably self-sufficient in the various filler and filter minerals. Prices of the various mineral commodities during the period 1950-1970 increased approximately as follows: barite, 43%; diatomaceous earth (filler), 49%; diatomaceous earth (filter), 55%; fuller&apos;s earth, 55%; talc. 77%; and bentonite, 94%. Actual usage of these mineral commodities as fillers and filters, during this period, showed changes approximately as follows: (1) Decrease-fuller&apos;s earth, 6%; talc, 15%; and bentonite, 29%. (2) Increase-barite, 113%; diatomaceous earth (filler), 150%; and diatomaceous earth (filter), -194%. A relationship between the amount of the various fillers and filters used and price increases is apparent. For example, barite increased only 43% in price, but its use as a filler has increased by 113%. On the other hand, talc, which increased 77% in price, decreased in filler use by 15%; and bentonite, which increased 94% in price, has decreased for filler and filter purposes by 29%. The actual decrease in the use of some of these commodities is not entirely caused by an increase in price. Competitive materials frequently have made substantial gains in the various filler and filter markets. For example, much of the bentonite used in the late 1940s and early 1950s for clarification of mineral and vegetable oils has been replaced by competitive materials. BARITE Occurrences and Sources In the United States, barite is produced from about 14 states, listed in approximate order of importance as follows: Missouri, Arkansas, Nevada, Georgia, Alaska, Tennessee, Kentucky, California, New Mexico, North Carolina, Washington, Idaho, South Carolina, Texas, and others. During the 20 years ending in 1970, almost equal amounts of barite were produced from Arkansas and Missouri. Within recent years, Nevada has replaced Georgia as the third leading barite--producing state. West Germany is second to the United States in barite production. Other important barite-producing countries include: Mexico, USSR, Italy, Greece, Canada, and Ireland. Ireland has become an important barite producer only recently. Barite is obtained from vein and cavity fill-

Jan 1, 1976