Search Documents

Joseph K. Stone, Jr. (Kaiser Engineers, Oakland, Calif.)—I would like to compliment the authors on their clear presentation of the results of their study of the pneumatic processes. We hope that the Inland Management decision to make this information available to all will induce others to release additional valuable fundamental data which they have accumulated in the field. There are two points upon which we would like to comment. In the discussion of Table VII it was indicated that the "oxygen consumptions were about the same as has been reported for other oxygen steelmaking processes". This conclusion is apparently based upon the consumption of 2100 cu ft per ton shown in Table VII. The data in Table IV also permits calculation of 2520, 2280, 2250 and 2700 cu ft per ton in heats 1 to 4, respectively. These figures are in the same general range as those reported for the Kal-Do and Rotor Processes using Thomas iron, but considerably above the following figures for four of the operating L-D Process Plants while using iron which is similar to American basic iron: Donawitz 1760 cu ft per ton Adapted from Cuscoleca' LinZ 1900 cu ft per ton Trenkler & Hauttmann2 Dofasco 1850 cu ft per ton D. O. Davis:3 In addition to the differences between the consumption of gaseous oxygen in the Inland operation and in the L-D Process, there is another closely related difference. The L-D plants for which data are cited are using approximately 1 pct ore while the authors' process used about 7 pct of sinter. Assuming 65 pct Fe in the sinter, the difference amounts to 400 to 500 cu ft

Jan 1, 1959

By H. J. Gluiskoter

The chlorine content of the coals in the Illinois Basin ranges from 0.00% to more than 0.60%. The chlorine content of the Herrin (No. 6) Coal has been mapped on a regional scale and, in general, increases with the depth of the coal. The depth-chlorine correlation exists because the coal is in apparent equilibrium with the composition of the ground water associated with it, and the salinity of the ground water generally increases with depth. At least part of the chlorine can be easily removed from the coal in the laboratory. In a natural weathering experiment, chlorine values decreased markedly during an 8-week period. Results to date indicate that none of the coals studied has a sufficiently high chlorine content to make it unusable in high-temperature steam boilers, although special steps may be necessary in the preparation or utilization of some of the highest chlorine coals. Investigations into the occurrence and distribution of chlorine in Illinois coals have been in progress at the Illinois State Geological Survey for over 35 years. Since 1948, chlorine analyses of face channel samples and of drill core samples of coal have been made routinely. The increased interest in chlorine and alkalies in coal in the U.S. followed that in Europe, where power plants during World War II were called upon to produce at higher levels than previously and with less down time for maintenance. Higher steam temperatures were reached, resulting in increases in the amount of fouling of external heating surfaces and in corrosion of boiler tubes when high chlorine coals were used. Early studies of the problem showed that coals with high chlorine content were more likely than those low in chlorine to cause difficulties in installations fired with powdered fuel. Crossleyl reported that the first rule of thumb developed for British coals was that coals considered to be high in chlorine (more than 0.30%) caused the most trouble, those intermediate in chlorine content (0.15% to 0.30%) were less likely to cause difficulties and those low in chlorine (less than 0.15%) generally were not associated with alkali bonded deposits and corrosion. However, this relatively simple picture was not adequate to characterize the difficulties that could be expected during the utilization of a large number of coals and Crossley1 developed another scheme for assessing the chances of superheater corrosion. This scheme took into consideration the observation that coals high in sulfur as well as chlorine are more likely to cause corrosion and fouling than coals low in sulfur and high in chlorine. Crossley also considered the ash content. When two coals had the same chlorine and sulfur contents, the one with the greater amount of ash would be the less likely to cause difficulties. Knowing only the amount of chlorine in a coal obviously will not give all the answers. Indeed, the significance of the chlorine content has been much discussed and it has been suggested that perhaps the total alkalies are a better indicator of possible troubles. The observation that the deposits that form

Jan 1, 1968

By J. F. K. Brown

ANTHRACITE in 1943, in common with the coal industry as a whole, passed through a year of wage negotiations that seemed endless. In the early months discussion of the United Mine Workers' demands was taken up and carried on continuously until May, finally reaching an impasse when the Union refused to continue at work, while submitting their demands to the War Labor Board. Thus a strike threatened, averted by the Federal Government taking over the industry, effective May 1, by order of the President. An office of the Bureau of Mines was established in Wilkes-Barre under the direction of J. J. Forbes, Mineral Production Security Division, as regional manager, who conducted operations until September, 1943, when the collieries were turned back to the operators. But the miners did not agree with the War Labor Board's award rendered in the fall, resulting in a recurrence of the previously threatened strike. again averted by Government control. In addition to the major upsets, a number of individual suspensions occurred at various mines. In spite of these drawbacks, to which might be added the difficulty of obtaining equipment and the scarcity of man power, the industry by November was only little less than a million tons short of the previous year. and in all probability, finally produced but little less than in 1942. This little less. however, was greatly missed in the market.

Jan 1, 1944

By J. A. Bartnik, Gerald D. Rose, William H. Benson

New techniques in the magnetite and heavy media beneficiation industries demand more efficient magnetic dispersion and flocculation of the finely ground particles. Demagnetizing coils must produce several major effects, such as improving classification and screening efficiency, decreasing moisture content in filter cake and improving separation selectivity and green pellet properties. Likewise, magnetic flocculators must increase filtering rates and the settling rates of solids, improve magnetite recovery and produce cleaner water. To improve the design of equipment and to conduct tests leading to the optimization of such dispersion and flocculation, a program was initiated at Eriez Magnetics. The major conclusions reached are: 1. Laboratory and plant scale tests conducted on magnetite products show that a demagnetizing force of 450 rms oersteds at 60 cycles for 1/20- second duration will depolarize natural magnetite particles coarser than approximately 10 microns. This has been found satisfactory for most applications. 2. Effective flocculation of magnetite was obtained when a slurry with more than one percent magnetite was exposed for a period of approximately 1/15 second to a 600-gauss field. 3. The cost of demagnetizers (or flocculators) increases rapidly for larger diameter pipes. In order to reduce the cost, narrow rectangular sections are recommended for magnetic flocculators. 4. For minimum operating cost, permanent magnetic flocculators are ideal, chiefly because they do not require any maintenance and have no operating cost. 5. A newly designed electro-demagnetizing coil with high heat dissipation and a nonmetallic core provides high efficiency and long life. 6. To select the correct magnetic flocculator (or demagnetizing coil) the following information is necessary: a. Magnetic product susceptibility b. Magnetic product coercive force c. Percent of magnetic product d. Flow rate e. Viscosity f. Structure of magnetic product

Jan 8, 1968

By J. B. Hess, C. S. Barrett

Single crystal rods of cadmium collapse under uniaxial compression into peculiar kinks if the (0001) glide plane is nearly parallel to the axis of compression. In his report first describing this behavior, Orowan1 proposed that these "kink bands" do not develop entirely by ordinary gliding and twinning but by a special mechanism in which glide lamellae of uniform thickness snap abruptly to a tilted position that permits lattice continuity across the glide planes. He concluded that a portion of each boundary of a kink band consists of a plane (non-crystallo-graphic) which bisects the angle between the glide planes on the two sides of it, and along which the bending and the dislocations are concentrated. The data presented by Orowan seemed to us to be insuffcient to conclude that a wholly new mechanism of deformation was responsible for the kinks. Therefore, we have investigated zinc, which is hexagonal close-packed and has an axial ratio near to cadmium, to see whether similar bands are produced, and whether the ordinary mechanisms of glide, bend-gliding, twinning, and the formation of deformation bands can account for its mode of deformation. We find that kinks form profusely in zinc as shown in Fig 1. The structure of these kinks, reported below, seems to require no new mechanism for their explanation, but indicates that kink bands are a special form of deformation bands and develop gradually, solely from basal glide. A theory covering the formation and structure of the bands is presented in detail because it is seldom possible to study deformation bands under such simple conditions, yet many principles applying to these kinks should also apply to deformation bands in general. Experimental Procedures Single crystal rods of 2-3 mm diam and 10-15 cm length were grown by the Brideman technique from swaged wire of Horsehead Special zinc in un-coated pyrex tubes. Orientations of the rods were determined with an optical goniometer after cleaving the rods at liquid air temperature. Crystals of desired orientations were then selected and used as "seeds" to grow additional crystals approximately 4 ft in length from which all specimens were cut. The wires were compressed in two ways: in a simple hydraulic handpress —a "soft" machine—and in a Riehle hydraulic testing machine modified to produce very "stiff" action by the simple expedient of inserting lengths of steel bars at the sides of the zinc crystals between the compression plates. For metallographic examination, the specimens were mounted in sealing wax. Hand polishing was employed, with no grits coarser than No. 1 paper; following the abrasives about 0.025 in. was removed by an etch-polishing reagent.* Final etching to reveal ori-

Jan 1, 1950

Page The Cobaltchromium Binary System (paper by A. R. Elsea, A. B. \Yesterman, and G. K. Manning, Met. Tech. June, 1948, Mechanism of Precipitation in a Permanent Magnet Alloy (paper by A. H. Geisler and J. B. Newkirk, Met. Tech. Aug. 1948, Tp 2444)................................................................................................. 300 Some Effects of Applied Stresses on Precipitation Phenomena (~aper by W. L. Finlay and W. R. Hibbard, Jr., Met. Tech. Sept. 1948, Tp 2470)....................................................................................... 301 Diffusion of Carbon in Austenite with a Discontinuity in Composition (paper by L. S. Darken, Met. Tech. Sept. 1948, TP 2443) 304 An Electron Diffraction Study of Oxide Films Formed on Nickelchromium Alloys (paper by J. W. Hickman and E. A. Gul- bramen, Met. Tech. June 1948, Tp 2372)..................................................................... 305 An Electron Diffraction Study of Oxide Films Formed on Copper-nickel Alloys at Elevated Temperatures (paper by J. W. Hickman and E. A. Gulbransen, Met. Tech. June 1948, TP 2391)................................................ 307 Decarburization of Chrome Nickel Alloys by Their Surface Oxides in High Vacua and at Elevated Temperatures (paper by E. A. Gulbransen, W. S. Wysong, and K. Andrew, Met. Tech. Sept. 1948, TP 2438)................................ 307 Fractographic Study of Cast Molybdenum (paper by C. A. Zapffe, F. K. Landgraf and C. 0. Worden, Met. Tech. Aug. 1948, TP 2421)................................................................................................. 308 Effect of Composition on Grain Growth in Aluminum-magnesium Solid Solutions (paper by L. J. Demer and P. A. Beck. Met. Tech. June 1948, TP 2374)............................................................................. 309 Effect of a Dispersed Phase on Grain Growth in Al-Mn Alloys (paper by P. A. Beck, M. L. Holzworth and P. Sperry, Met. Tech. Sept. 1948, TP 2475)................................................................................. 310 Statistical Rate Theory of Metals—Mechanism of Flow and Application to Tensile Properties (paper by J. W. Fredrickson and H. Eyring, Met. Tech. Aug. 1948, TP 2423)............................................................... 315 Nucleation of Slip Bands (paper by J. G. Leschen, R. P. Carreker, and J. H. Hollomon, Met. Tech. Sept. 1948, TP 2476) and.. 318 Transient Plastic Deformation (paper by R. P. Carreker, J. G. Leschen, and J. D. Lubahn, Met. Tech. Sept. 1948, TP 2477).. 318 Plastic Deformation of Large Grained Copper Specimens (paper by W. R. Hibbard, Jr., Met. Tech. Sept. 1948, TP 2469). ... 323 Plastic Flow in Anisotropic Sheet Steel (paper by L. R. Jackson, K. F. Smith, and W. T. Lankford, Met. Tech. Aug. 1948, TP 2440)................................................................................................. 323 The Effect of Thermal-mechanical History on the Strain Hardening of Metals (paper by J. E. Dorn, A. Goldberg, and T. E. Tietz, Met. Tech. Sept. l948, TP 2445)....................................................................... 325 The Room and Elevated Temperature Properties of Some Sand Cast Magnesium-base Alloys Containing Zinc (paper by T. E. Leontis, Met. Tech. June 1948, TP 2371)..............................................................., 327 The Low Temperature Properties of Tin and Tin-lead Alloys (paper by H. S. Kalish and F. J. Dunkerley, Met. Tech. Sept. 1948, TP 2442)............................................................................................335 Thermal and Electrical Properties of Ductile Titanium (paper by E. S. Greiner and W. C. Ellis, Met. Tech. Sept. 1948, TP 2466).................................................................................................... 335 Property Changes during Aging (paper by A. H. Geisler, Met. Tech. Aug. 1948, TP 2436)............................... 337 Factors Affecting the Tensile Notch Sensitivity of Magnesium Alloy Extrusions (paper by I. Cornet, Met. Tech. Aug. 1948, TP 2419)................................................................................................. 338 Effect of Grain Size on Tensile Strength, Elongation and Endurance Limit of Deep Drawing Brass (paper by H. L. Walker and W. J. Craig, Met. Tech. Sept. 1948, TP 2478)............................................................. 339 A Copper-base Alloy Containing Iron as a High-strength, Highconductivity Wire Material (paper by W. Hodge, R. I. Jaffee, J. G. Dunleavy, and H. R. Ogden, Met. Tech. Aug. 1948, TP 2422).............................................. 340 A High Strength-High Conductivity Copper-silver Alloy Wire (paper by W. Hodge, R. I. Jaffee, J. G. Dunleavy, and H. R. Ogden, Mel. Tech. June 1948, TP 2366)...................................................................... 340 The Effect of Chronlium on the Ma Point (paper by J. B. Bassett and E. S. Rowland, Met. Tech. Aug. 1948, TP 2417.... 341 The Kappa Eutectoid Transformation in the Copper-silicon System (paper by W. R. Hibbard, Jr., G. H. Eichelman, Jr., and W. P. Saunders, Met. Tech. Sept. 1948, TP 2441).............................................................. 343 Stabilization of the Ausknite-martensite Transformation (paper by W. R. Harris, Jr. and M. Cohen, Met. Tech. Sept. 1948, TP 2446)................................................................................................ 344 Secondary Hardening of Tempered Martensitic Alloy Steel (paper by W. Crafts and J. L. Lamont. Mel. Tech. Sept. 194,8, TP 2439)................................................................................................. 345

Jan 1, 1950

By Niels Hansen

Dispersion-strengthened aluminum products consist of an aluminum matrix containing finely distributed ceramic or intermetallic particles. Examples of the two types of product are SAP, in which the dispersed phase is aluminum oxide, and materials made from atomized aluminum alloy powder, in which the dispersed phase can be FeA1, particles.' A fundamental difference between the two types of product is that the elongation of aluminum/aluminum oxide products decreases with increasing temperature, whereas the elongation of aluminum- FeA13 products, like that of aluminum alloys, increases with increasing temperature. As regards the structural stability, aluminum/aluminum oxide products are stable to temperatures above 600° C as aluminum oxide does not react with aluminum, whereas prolonged heating at above 400°C of aluminum-FeA1, products leads to coarsening of the intermetallic phase and loss of strength.' On the basis of these results it is supposed that a dispersion-strengthened product combining strength, ductility, and stability at elevated temperatures may be obtained if the dispersed phase reacts with the matrix in such a way that the reaction does not proceed at any significant rate at the application temperature. Different ceramic or intermetallic compounds may be selected as the dispersed phase, and, as alloying of the matrix phase may also influence the reaction, many possibilities exist for each metal. In the present study, aluminum products containing different oxides have been examined. For a reaction to take place between the dispersed oxide and the aluminum the free energy of formation of the oxide (MeO) must be greater than that of aluminum oxide; the difference should, however, not be too great in order to limit the reaction rate. Furthermore the aluminum alloy formed when aluminum reacts with the dispersed oxide should have a melting point near

Jan 1, 1969

By William R. Webster

At the Florida meeting of the Institute, in March, 1895, I presented a Note on a Proposed Scheme for the Study of the Physics of Cast-Iron,1 giving an outline which, for convenience of reference, I here repeat. Suggested Lines for DiScuSsion and IvestiGation. I.—Correspondence between chemical composition and melting-point, fluidity, shrinkage, fracture, chill, micro-structure, and other physical properties. II.—Influence of: 1. Cupola-mixture, use of steel and other scrap, oxidized or clean material, 2. Manner of melting, flux, etc., 3. Casting-temperature, A. Fracture. 4. Manner of handling melted metal and B. Micro-structure. method of casting, C. Physical properties. 5. Size and form of casting, D. Shrinkage. 6 Kind of mold, green sand (under dif- on E. Chill. ferent conditions of ramming, amount F. Residual strew of moisture, and skin-dried), dry sand, G. Condition and quan- loam, and chills, tity of carbon and 7. Rate and mode of cooling castings, other elements. 8. Manner and temperature of heating for annealing, 9. Additions of nickel or aluminum, III. —-Segregation as affected by : 1. Composition ; 2. Casting-temperature; 3. Rate of cooling ; 4. Size and shape of casting. IV. —Blow-holes, their volume and position as affected by: 1. Composition; 2. Casting-temperature; 3. Casting-pressure ; 4. Rate of cooling; 5. Size and ehape of casting ; 6. Special additions. It was hoped that a discussion might thus be elicited, similar in interest and value to the discussion of the physics of steel, which had been so widely and gratefully welcomed by students and practitioners in that department. That this hope was not

Jan 1, 1905

By Walter R. Hibbard, Harold Margolin

The effect of ten ternary additions on the aging of a Cu-Ag alloy was measured by X ray, microstructure and hardness. A supersaturated copper-rich transition structure was found. The effect of the ternary element was related to differences between transition and precipitate lattice parameters and analogies with solution and strain hardening. IN addition to the prerequisite of diminishing solid solubility with falling temperature, the theory of coherency hardening1 proposes that the principal source of hardening during precipitation is strain caused by coherency between the matrix and precipitate. For a given system greater coherency hardening would result from lengthening the period of coherent growth and/or increasing the number of nuclei, other things remaining equal. However, the hardness change during aging is a function of a number of phenomena in addition to coherency hardening, such as dispersion hardening, loss of coherency, solute depletion, matrix recovery or recrystal-lization, coalescence, and their relative time sequences. The present investigation was undertaken to study the effect of ternary additions on the age-hardening of Cu-Ag alloy. For this purpose a series of alloys were made containing as ternary constituents Mg, Al, Si, P, Mn, Ni, Zn, As, In, and Sb. These elements were added to a master 5 wt pct Ag in Cu alloy in such amounts as to obtain alloys listed in Table II containing the following approximate atomic percentages: 96 pct Cu, 3 pct Ag, 1 pct ternary addition. A 97 atomic pct Cu, 3 atomic pct Ag alloy was used as a comparison standard. There have been numerous investigations of age-hardening in Cu-Ag alloys2-lo but few of ternary Cu-Ag alloys. Pfister and Weist" found that 1 wt pct Ni reduced the solubility of Ag in Cu above 600 °C and that the rate of precipitation was slower than in polycrystalline Cu-Ag alloys of similar silver content. More recently Hodge, Jaffee, Dunleavy, and Ogden12 investigated the effect of ternary additions of Mg, Li, P, Cd, Zn, Zr and Be on strength properties of Cu-Ag alloys. Mg, Cd, and P were found to increase strength in the aged and cold-worked condition. Experimental Procedure Charges weighing 7.5 lb were melted in a closed carbon crucible under a reducing atmosphere* of nitrogen and hydrogen. A Durville-type casting procedure with a hot-top arrangement was used to obtain a sound casting, 2x2x43/4 in. Prior to rolling and annealing of the ingots, a trial solution anneal of rolled sections of the hot-top portions indicated that at 780°C melting was avoided except for the Cu-Ag-Sb alloy. This alloy could not be produced as a single phase within the limits of temperature control. i 3" to 5oC, since melting occurred at 64O °C, and below this temperature precipitation was

Jan 1, 1952

By AIME AIME

To accompanying photograph of the plant of the Beattie Gold Miner Limited, at Duparquet,. Quebec, is taken from the east and shows the open-pit from which the ore is taken during the summer. The buildings on the level ground above the open-pit are the change rooms, steel shop hoist building, compressor building, machine shop, warehouse, carpenter shop, and oil house. The main five-compartment shaft is shown west of the hoist building. The crusher plant adjoins the headframe and a long conveyor transports the fine ore

Jan 1, 1936

By Thomas L. Kesler

Essentially all of the barite produced in Georgia has come from the Cartersville district in the northwest part of the state. The earliest recorded shipment of ore, 60 tons, was made in 1894.1 With the exception of the four-year period 1931 to 1934, the separate yearly output has been recorded and published since 1915, whereas the total yearly output of the United States has been published since 1880. The separately recorded production of Georgia (Cartersville) through 1947 is 2,232,544 short tons valued at $14,900,746,2 but unpublished data on the period 1931 to 1934, plus the estimated unrecorded output prior to 1915, make the actual total about 2,400,000 short tons. This is about 21 pct of the total production of the United States, which, through 1947, is 11,328,440 short tons valued at $71,683,386.2

Jan 1, 1949

By W. H. Somerton

The effects of drilling variable on rotary drilling rates and efficiencies have been studied by a series of laboratory drilling tests. TWO-cone 1.25-in. diameter hits were used to drill vertically upwards into rock samples at corltrolled weights and rates of rotation. Shale, sandstone and specially prepared concrete samples were used in this study. Power input to the ririllirig systeln was measured and drilling chips collected for energy — .size reduction studies. Reasouably good correlations between drilling variables and rates of penetrotion were found. Qrrantities that are difficult to evaluate include rock strength parameters and the effects of bit wear. Effects of bit size and geormetry require further investigation. Analysis of the drilling chips confirmed the premise that, for rocks containing two or more mineral constituents of diflerent strengths, a greater amourrt of rock breakage occurs in the weaker constituent. Drilling conditions which required greater amounts of energy produced finer drilling chips. As bit tooth wear progressed, drilling chips became finer. Efficiency of rotary drilling as a rock breakage mechanism was extremely low. Comparison was made with theoretical energy requirements and with energy requirements for size reduction by comminution methods. INTRODUCTION Many technological developments and innovations have made possible the successful drilling of oil wells by the rotary method to depths exceeding 20,000 ft. Bigger, more powerful rigs, better steels, improved bit design and more careful control of the circulating system have all contributed to this success. Despite these advances comparatively little is known regarding the basic mechanism of rock breakage by the rotary drilling process. Future improvements and, in particular, reduction of drilling costs will undoubtedly require a clearer understanding of the variables controlling effectiveness and efficiency of rotary drilling. Rotary drilling is inherently an inefficient means of producing rock breakage. Loss of energy in transmission from the surface to the cutting mechanism may be large, thus limiting the total amount of energy which may be applied to rock breakage. Increased efficiency may be realized by improved energy transmission methods such as the turbodrill. Conversion of transmitted energy to rock breakage by use of rotating cutter teeth is likewise inefficient. Improvement of cutter efficiency has been obtained essentially by empirical means —changes in bit tooth size, shape and spacing, and tooth deletion to give clean bottom-hole patterns. The present work was undertaken to investigate the factors controlling rates of bit penetration under laboratory drilling conditions. Laboratory drilling apparatus is shown in Fig. 1. The effects of rock strength and bit wear on drilling rates were investigated. Drill cuttings were analyzed to determine the character of breakage and to compare this with other methods of producing rock breakage. VARIABLES INVOLVED IN ROTARY DRILLING Some of the variables controlling bit penetration rates can be studied conveniently by dimensional grouping. R/DN f(F/D2S) or

By AIME AIME

ON May 5, the Washington, D. C., Section, A.I.M.E., devoted its meeting to the many-sided and perplexing question of mineral stock-piling for peace. Opening the symposium, Harry J. Wolf, of the War Production Board, outlined the problem under six heads: (1) Technical. Mechanical, chemical, or metallurgical importance of specified materials, emergencies that might arise, relative scarcity, and critical value of stock piles during emergencies. (2) Economic. Cost to Government, influence of Government stocks on commercial relationships and markets, effect of availability of items as a con¬structive influence on industry, Administration policies now and during postwar period. (3) Legislative. Need for immediate legislative action, need for legislation on postwar conditions as well as on current requirements, a constructive basic policy to prevent political manipulation. (4) Military. Consideration of re¬quirements and supplies bearing on national safety and needed for manufacture of equipment, and adequate reserves of scarce materials for research or experimentation by military agencies. (5) International. Interests of the United Nations in contradistinction to those of the United States; effects of nonisolation policy on nature, location, and administration of stock piles. (6) Negative stock-piling. Question of United Nations' legislation to prevent stock-piling by Axis nations after the war and who shall purchase stock-pile materials and during what periods.

Jan 1, 1943

[I-Institute of Metals Division PAUL D. MERICA, Chairman ZAY JEFFRIES, Vice-chairman W. M. CORSE, Secretary General Committee ROBERT J. ANDERSON H. C. JENNISON L. W. SPRING WILLIAN K. FRANK DAVID LEVINGER R. L. SUHL J. R. FREEMAN, JR. PAUL McKINNEY R. F. WOOD]

Jan 1, 1928

By Brandon H. Grove

In Austria's only producing field, at Zistersdorf, Erdoel Produktions-gesellschaft completed a single new producer, its well Gosting 6 coming in early in October for an average production of about 15 tons daily. For further testing within the proved part of the field this company's Gosting 7 was at the close of the year drilling in Pannonian strata at 760 m., and its Gosting 8 was rigging up. Outside of the proved area of the Zistersdorf field two further tests located on the Steinberg dome failed to find production in the known oil-bearing strata of the Sarmatian, and were deepened as wildcats into the Cretaceous Flysch. The first of these, Neusiedel 1, about one kilometer north of the known producing area, found oil in the Flysch beds at a depth of 1290 m. for an initial production of about 10 tons per day. The second test, Windisch Baumgarten la, is an old well previously considered a failure, which when deepened achieved a production of about 5 tons per day in the Flysch Inoceramus beds at 985 m. Neither of the foregoing wells is producing from a stratigraphically definable horizon, oil accumulation in the Flysch of this area being apparently controlled by tectonic breccias or related crevices.

Jan 1, 1937

By John Griffen

THEORY HYDRAULIC classification as explained by Rittinger and others was largely restricted to conditions wherein the free-falling velocities of the particles were conceived as governing the separations effected (see chapter 9). The laws governing classification under free-falling conditions have been summarized by Chapman and Mott as fo1lows:l Nomenclature r represents, in a particle of irregular shape, the round-hole screen through which the particle would pass, or some other linear dimension of the particle equivalent to d, the diameter of a sphere. s, the specific gravity of the particle. 1, the specific gravity of the water used as a medium. K, a constant. W, the velocity of the water. In an Upward Current of water 1. A particle will move upward if [V > K dr(s - 1)] and, by suit- ably regulating the speed of the water current, the larger and heavier particles may be made to fall downward against the current, leaving the smaller, lighter particles in suspension in the current. 2. Particles such that [- = -] cannot be separated in an upward- current classifier with any one velocity of current. Coal particles having a specific gravity of 1.35 cannot be separated from refuse particles of [2.5 - 1 2.5 sp. gr.] unless the ratio of diameters is less than [ 4.3 to 1, 1.35 – 1] and the raw coal must be screened to size limits within this ratio if they are to be separated. Cone-shaped vessels or vessels of other shapes that allow the use of different velocities of current at different points in the flow are used to modify this limitation.

Jan 1, 1943

By Arthur Notman

THE raw material men in all industries, and copper is no exception, are accustomed to think of them- selves as the whole show, and not without justice, for if there were no copper mines the world would have no copper. Nevertheless, many different things costing money and resulting in profits must be done to their product before it is ready for the world's use. In other words, they are making the frequent mistake of Chinking in terms of partial costs. Nobody really uses electrolytic copper. Possibly that is why nobody seems willing to pay anything for it. The manufacturers, being canny, do not buy any more electrolytic than they feel that they can work up and sell profitably, although they like to make the raw material men Chink that they will take all that can be produced. This is a state of affairs that has aroused my sympathy and curiosity, and has induced me to study the financial history of the copper wire and brass industry of the country or such portion of it as publishes any records readily available to the curious minded. About 60 per cent of the electrolytic copper used in this country is drawn into wire and consumed by the electrical industries. The remaining 40 per cent is

Jan 1, 1926

By R. C. Ku, A. J. McEvily, T. L. Johnston

The microplastic response of a series ofas-quenched Fe-Ni-C martensites has been measured at 77°K. At strains less than JO'3 the flow stress is governed primarily by the transformation-induced dislocation structure of the martensite. Only at strains in excess of 10-3 is the influence of carbon manifested in the flow stress. At these macroscopic strains, typically 10-2, the solid-solution hardening is proportional to (wt pct C)1/3, and, in an alloy containing 0.39 wt pct C, amounts to 50 pct of the flow stress. THE technological significance of high-strength ferrous martensite has stimulated many investigations of its structure and properties. Although our knowledge of the characteristics of martensite has increased immensely, especially with the advent of high-resolution techniques, an understanding of the basic strengthening mechanism still remains elusive. The purpose of the present paper is to consider certain aspects of micro-plastic behavior of Fe-Ni-C martensite which we feel can help to resolve this important problem. Such alloys are particularly suitable for experimental investigation because their compositions can be adjusted to reduce the M, to a temperature low enough essentially to eliminate the diffusion of carbon in the freshly formed martensite.1 The mechanical properties in this condition are of interest inasmuch as they reflect a state that is free of the important but complicating influence of precipitation processes. In this virgin martensite the carbon is distributed as it was inherited from the parent austenite; i.e., it is present interstitially, and gives rise to tetragonality through strain-induced ordering.' In order to determine the source of strength of such alloys, Winchell and Cohen1 investigated the low-temperature macroscopic stress-strain behavior of a series of virgin martensites of increasing carbon content but of common M, temperature (-35°C). They found that the flow stress increased rapidly with carbon content up to 0.4 wt pct; beyond this point the flow stress increased at a much slower rate. It was concluded that martensite is inherently strong. To account quantitatively for the strength of virgin or as- quenched martensite in terms of the role of carbon, Winchell and cohen3 suggested that the carbon atoms, trapped in their original positions by the diffusionless martensite transformation, interfere with dislocation motion according to a model akin to that of Mott and Nabarro. 4 In this treatment, individual carbon atoms are considered to constitute centers of elastic strain and thereby generate an average stress resisting the motion of dislocations throughout the lattice. The additional stress necessary to move dislocations, over and above that necessary for motion in a carbon-free martensite, is given by where L is an effective length of dislocation capable of motion. L was assumed to be limited to the spacing between the twins that are an essential structural element of Fe-Ni-C martensites. They assumtd the spacing to be invariant and of the order of 100A. However, recent work5 has shown that L is variable and can be in excess of 1000Å, so that the assignment of an appropriate value of L is not straightforward. In contrast to the above conclusion that there is an intrinsically high resistance to plastic flow, it has been suggested by Polakowski6 that freshly quenched martensite is in fact "soft" in the sense that dislocations are initially free to move upon application of stress. The high indentation hardness and macroscopic yield stress of ferrous martensites are then a consequence of rapid strain hardening that depends upon carbon in solution. Consistent with this point of view are the results of Beau lieu and Dubé who measured the rate of recovery of internal friction as a function of aging (tempering) temperature in a freshly quenched steel containing 0.90 wt pct C, 0.37 wt pct Mn, 0.1 wt pct Cr, and 0.07 wt pct Ni. The kinetics were clearly consistent with the idea that many dislocations are unpinned in the as-quenched state and that during aging they become progressively pinned by carbon at a rate controlled by carbon diffusion in the body-centered martensite lattice. In order to provide a basis upon which to distinguish between the "hard" and "soft" interpretations indicated above, we have made studies of the initial stages of plastic deformation in Fe-Ni-C martensites similar to those'used by Winchell and Cohen. It will be shown that the results support the contention that dislocation segments in as-quenched material are indeed

Jan 1, 1967

By CHARLES M. SCHWAB

THE ENGINEERS have placed this great country of ours in a preeminent position with everything pertaining to manufacture, metallurgy, and the kindred arts. We are second to none in the world. We have a country which, another speaker has said, God has endowed with such riches in coal and natural resources as no other country in the world. But rich as these are, there is one thing greater; the sturdy character, energy, and integrity of its people, which will make these great resources an influence in the world's developments. Great as are these resources and the energy and integrity of our people, there is one problem of our .engineering, which I term human engineering, that is of far more importance than the creation of machines and methods, with which you have been so successful in the past. Of what value is the skillfully devised machinery, the complex process, unless manned and operated by people whose heart and soul are in sympathy with the work they are doing and who have before them the giving of a complete day's work for a day's pay?

Jan 1, 1920