Search Documents

. S. W. PARR, * Urbana, Ill. (written discussion ? ).-Multiplication of argument is unnecessary to establish the desirability of coking coals at low temperatures, that is to say, below 1200° F. The value of the semi-coke thus produced would doubtless go far toward solving the problem of smoke prevention, and suggests the possibility of the substitution of a smokeless fuel for anthracite and so-called smokeless coals. Whether such coke would have any value as metallurgical coke is a question which cannot be answered for lack of any experimental data in the use of such material. Of course interest is accentuated, at the present time, in the amount and character of the tars, which promise greatly to exceed in values the products obtainable from. the high-temperature process. The difficulties encountered in adapting the principles of low-temperature carbonization to industrial methods are well nigh insurmountable. Briefly stated, there is involved the heating of the center of a mass of non-conducting material by the external application of heat. It is a well established fact that the center of the mass of coal in a standard

Jan 11, 1918

By J. F. Lewis

Believing that one of the essential points in mining, as in all other business, is to know the expense incurred in each particular department, I have carefully kept an account with each department for the past three years; and, as it may be of interest to some of our members, I herewith present it to the Institute, reduced to per centages of the total yearly expense, showing the cost for materials, repairs, expenses, tools, team accounts, powder, oil, and fuel, also for labor under its several heads: 1875—Materials. 1875—Labor, Repairs,...040 Expenses,....016 Team,. .. .. .017 Machinery,. .. .055 Tools,..006 Repairs,. .. .027 Improvements,.....030 Washer,. .. .076 Oil ..008 Pit,.. 178 Powder,..,043 Dirt,.. 130 Fuel,. .325 Superintendence,. ..050 .485 .516 100.1 1876—-Materials. 1876-Labor. Repairs,. . • .. .043 Expenses,......012 Team,.011 Machinery,. .. .090 Tools,..005 Repairs,... 027 Improvements,.....007 Washer,. .. .085 I,. ...,015 Pit,.. 139 Powder,. .. .. .030 Dirt,.. 160 Fuel,...321 Superintendence,. ..078 .444 .559 100.3 1877—Materials. 1877—Labor. Repairs,......102 Expenses,......019 Team,..031 Machinery,. .. .050 Tools,..030 Rrpairs,. .. .046 Improvements,....,031 Washer,. .. .057 I,...009 Pit,.....179 Powder,...035 Dirt,.. 162 Fuel,...200 Superintendence,. ..054 .457 .548 100.5 Average for the three years 1875, '76, and '77. Materials. Labor. Repairs,...062 Expenses,...016 Team,..016 Machinery,. .. .065

Jan 1, 1879

By C. E. Corson

THE experiments of which the results and significance are set forth in this paper do not by any means cover the whole subject of the heat-treatment of the material referred to, yet they constitute a contribution to that general subject, rather than to the special department of annealing. The material here considered is acid open-hearth steel, containing from 0.50 to 0.80 per cent of carbon, with a nearly uniform percentage of other elements. This class of steel is rapidly increasing in commercial importance. It is even rumored that the rail-specifications of some railroads will hereafter require open-hearth steel. Yet this particular grade seems to have received less study and description from the standpoint of the metallographist than many others. The investigation here described was directed to the following points:-Steel containing about 0.50 per cent, of carbon : 1. The structure as related to the temperature, at the same rate of cooling; 3. The structure and physical properties as related to temperature at different rates of cooling; 3. The structure and physical properties as related to different finishing-temperatures and different rates of cooling; 4. The bearing of these observations upon the statement of Prof. Albert Sauveur.1

Sep 1, 1906

By G. A. Beiswenger

The application of the law of supply and demand to the sale of crude oil is generally conceded, but the motives underlying the buyer's (refiner's) demands are not always obvious to the seller (producer). In some cases this obscurity has led to the conclusion that the refiner may be unnecessarily particular when he selects one crude and rejects another. This preference, however, is very largely the reflection of the refiner's product demands and the quality of the stocks obtainable from the selected crude. The purpose of this paper is to point out critical characteristies of the major classes of refined products and to show how crudes vary in their suitability for such products. With relatively few exceptions, available processing methods and addition agents make it theoretically possible to produce any type of refined product from any crude source, although it may not be economically sound to do so. The widespread application of thermal cracking for converting higher boiling stocks into gasoline is well known. More recently cracking and refining in the presence of catalysts9 have been developed, as well as various processes for polymerizing lighter hydrocarbons into gasolines having desirable characteristics.6 For several years, selective solvents have been applied commercially to refining inferior quality kerosene, Diesel fuel and lubricating oil distillates.3 Improved methods for refining lubricating oils from crude residual4 formerly suitable only for fuel, are now in use and a number of special solvent processes are available for dewaxing lubricating oils to low pour point.5 These improved refining methods have been developed not only to meet the demand for improved product quality but also to enable the refiner to obtain quality products from crude sources that would not yield such products by the older refining methods. In many cases, the utilization of these modern refining tools necessitates an appreciable expenditure for equipment as well as added manufacturing costs, and their application therefore must be justified economically. Despite the availability of such tools, the added processing costs involved and yields obtainable may render their application entirely impractical. To illustrate this point, inspections of typical cuts from various crudes

Jan 1, 1940

Homestake's Bulldog Mountain Operation near Creede, Colorado, in the San Juan Mountains at an elevation of nearly 2,750 m (9,000 ft), is subjected to short summers and long cold winters. Creede’s history dates back to 1889 when silver ore was discovered; and by 1892 production of over a million dollars per month was being shipped from mines located along the Amethyst Fault. The Bulldog Mountain Fault remained relatively untouched by the early prospectors. The United States Geological Survey recognized the potential of this fault in 1960, which led to the staking of many claims over the structure. Homestake leased properties in 1963 and in mid- 1964 a tunnel was started at the 2,956 m (9,700 ft) level with encouraging mineralization being encountered. In 1968 a decision was reached to build a flotation mill of 318 mtpd (350 stpd) capacity. The erection of the mill was completed in early 1969, six years after the first exploration was begun. Since initial start-up, extensive drifting has been done on several separate levels. Two underground hoist installations serve the various levels and many thousand feet of vertical mining operations. Due to the unconsolidated nature of the vein, a new unique underhand cut-and- fill mining method was developed. This procedure is the reverse of the normal cut-and-fill and proceeds from the top down under cemented sand fill, which, while expensive, has greatly reduced s toping hazards. Prior to 1977, a considerable quantity of silver was lost in the slime fraction of the ores processed because of oxidation and other inherent characteristics of individual minerals. Due to Homestakefs favorable experience in treating the slime fraction of the Lead, South Dakota gold ores, experiments with leach methods to recover silver from the slimes by Carbon -In -Pulp offered' the potential for additional silver recovery. Work was begun on the Carbon-In-Pulp plant in April 1976 and completed in December of that year at a cost slightly exceeding $2 million. The C. I. P. plant was designed for 136 mtpd (150 stpd) of current plant slimes plus 227 mtpd (250 stpd) of slimes dredged from the old tailings during the summer season. The sand fraction of the flotation

Jan 1, 1981

By T. H. Aldrich

THE Aldrich Mining Co. holds under lease from the Illinois Central R. R. Co. about 14,000 acres, in the East half of Township 12, Range 12 `V., in Marion county, Alabama, and owns other lands, of which about 1,000 acres adjoin this leased tract, making a total area of about 15,000 acres, all of which is underlain by the coal-seam upon which the company is operating. This seam is nearly horizontal ; and a ravine, diagonally crossing the tract, exposes the outcrop on either side for about 2 miles. The territory has been so divided that nearly the whole of it can be worked out by two collieries. The mines at Brilliant were opened in the Fall of 1898, and shipments began in the following spring. The original plan was to furnish steam-coal for locomotives to the Illinois Central R. R. Co.; and upon this expectation the investment of capital was made. The field was entirely new; and the softness of the coal at the outcrop induced the belief that it could be very cheaply mined. A contract for the delivery of a large quantity of coal to the railroad was accordingly executed. But with the advance of the entries to increasing distances from the outcrop, the coal proved so hard that it could no longer be drilled with a breast-auger; and the expense of mining became so great that the contract for cheap steam-coal had to be cancelled. It became evident that the work must be done with machinery and explosives, if it could be profitably done at all. On the other hand, the excellent quality of this coal opened, at the same time, a possible market not specially contemplated at the outset-namely, that of a first-rate coal for domestic and general uses. Since no other deposit of such coal was known to exist on the line of the Illinois Central, or any other railroad

Jul 1, 1906

By R. W. Diamond

Low-grade ores can be designated by two main classifications: (1) simple low-grade ores, and (2) complex low-grade ores. As a rule the first type has a relatively small metal content, although low- grade iron ores contain a rather high percentage of metal. As the simple type is the one that is ordinarily in mind when the term "low-grade ore" is used, the paper will be devoted mainly to ores in this general category. Cheap treatment is the prime requirement in utilizing low-grade ores of the simple type, although in some cases the value of nonmetallic by-products, such as limestone for fer- tilizer and silica for flux, allows a little more lati- tude than in the usual situation. When the costs are divided under the three headings-mining, milling, and smelting-it is apparent that the last group will not constitute an important factor as a rule because the high concentrating ratio makes the smelting cost per ton of ore fairly low.

Jan 1, 1949

By Harlan W. Nelson, James B. Purdy

A study of data obtained during laboratory tests to determine the suitability of bituminous coals for use in residential underfeed stokers of the clinkering type has led to the following general conclusions: 1. Performance data obtained during the test furnish useful and practical information upon which to judge the performance of stoker coals. 2. Conclusions derived from the results of evaluation tests are in general agreement with use experience of the coals in the field. The method is of practical use in this regard. 3. Few direct relationships were found between data furnished by the evaluation test and determinations by standard laboratory tests. This is particularly true with regard to coke formation and clinker formation, two of the most important factors in determining the degree of satisfaction to be obtained in applications of the small underfeed stoker. It has not been the intention in this paper to prescribe this evaluation test as the best method for the evaluation of coals for use in residential stokers. That there are other test methods having similar objectives serves to point out the necessity for full-scale laboratory tests. At the present time, a standard test procedure for the evaluation of coals for use in residential stokers is not available. For the past several years a joint committee, appointed from the membership of the Residential Stoker Committee of Bitulninous Coal Research, Inc., and from the Engineer- ing and Research Committee of The Stoker Manufacturers Association, has been working to develop a standard procedure for testing and evaluating bituminous stoker coals. This procedure has been completed to the extent that it has been drawn up in tentative form. It is now planned to install the equipment in several laboratories and to run check tests, using portions of identical lots of coal, to determine the degree of reproducibility offered by the method. Completion of this standard test procedure should greatly facilitate the evaluation of coals for use in residential stokers. Acknowledgments The cooperation of coal operators sponsoring the coal evaluation tests, in granting permission to use data and results from their tests, is gratefully acknowledged. Acknowledgment is also made to Carroll F. Hardy, Chief Engineer, Appalachian Coals, Inc., for his interest and timely suggestions on the preparation of this paper. Special thanks are due to Ralph Sherman, Assistant Director, Battelle Memorial Institute, who was largely responsible for development of the evaluation procedure, for helpful suggestions and advice. References I. H. A. Sherman: The Evaluation of Coal for Use in Domestic Stokers. Univ. of Ill., Eng. Experiment Station, Circular No. 39 (1939). 2. . Q. Shotts: The Relation of Free- swelling Indexes to Other Characteristics of Some Alabama Domestic Stoker Coals. TP 2314, Coal Tech., (Feb. 1948); Trans. AIME (1948) 177, 502. 3. . J. Helfinstine and C. C. Boley: Correlation of Domestic Stoker Combustion with Laboratory Tests and Types of Fuels 11. Combustion Tests and Preparation Studies of Representative Illinois Coals. Ill. State Geol. Survey, Re1. of Zntlestigations No. 120 (19467 ) p. 35. DISCUSSION E. R. Kaiser*—AS a former fuel engineer assigned to residential stokers at Battelle, the writer has read with considerable interest the paper by Messrs. I'urdy and Nelson. It is gratifying to note that earlier test techniques have been developed and that criteria found important in the years 1935 to 1938 are still important in judging the performance of stoker coals for residential heating. The authors have plotted a number of the primary coal data singly against performance data of the stoker in an effort to establish relationships. Unfortunately, wide scattering of points usually resulted, which did not illustrate what experience generally indicates to be the case. For example, Fig 3 indicates almost no trend in the percentage of released ash converted to clinker with change in ash-softening temperature. Other factors, such as fuel bed temperatures and zones of heat release must have influenced the results. In the present state of our knowledge, we cannot explain all of the reasons why suitable stoker coals perform satisfactorily, nor why one satisfactory coal may be better than another. It would therefore

Jan 1, 1950

The following is an incomplete list of members and guests who called at Institute headquarters during the period Nov. 10, 1918 to Dec. 10, 1918. Arthur C. Adair, Camp Meade, Md. L. S. Mitchell, Montreal, Canada. Arthur K. Adams, Camp Humphreys, Va. T. E. Mitchell, San Francisco, Cal. Toner Antisell, Chevy Chase, Md. H. Mortimer-Lamb, Montreal, Canada. V. W. Aubel, New Castle, Pa. Edmund Newton, A. C. Black, El Paso, Tex. Paul T. Norton, Jr., Columbus Ohio. 0. F. Brinton, Baxter Spgs., Kans. Elmer W. Pehrson, San José, Cal. C. S. Corbett, Minneapolis, Minn. Joseph E. Pogue, Washington, D. C. W. M. Corse, Mansfield, Ohio. T. C. Roberts, E. Orange, N. J. G. C. Crossley, Toms River, N. J. D. R. Semmes, Richmond, Va. H. S. Emlaw, Grand Haven, Mich. H. L. Slosson, Jr., San Francisco, Cal. Rudolph Emmel, Boston, Mass. W. H. Staver, S. G. Garrett, U. S. N. R. F. A. L. Sweetser, Boston, Mass. Lt. Francis Geib, Denver, Colo. Lt. H. B. Taylor, Kansas City, Mo. Wm. E. Hubbard, Wichita Falls, Tex. Kirby Thomas, New York. Arthur Iddings, Wichita Falls, Tex. Benj. F. Tibby, Salt Lake City, U. Zay Jeffries, Cleveland, Ohio. J. L. Towne, Whitepine, Colo. S. J. Kidder, Mogollon, N. M. Chas. W. Tubby, St. Paul, Minn. Lt.-Col. W. H. Lanagan (Engrs.). A. G. Waite, Brookline, Mass. Major W. F. Lewis (Engrs.). Timothy D. Walsh, Denver, Colo. 0. M. Lewyn, Thomas Warner, Phoenix, Ariz. A. McClintock, DeKalb June., N. Y. J. P. B. Webster, London, England. Major Donald G. Miller, N. M. E. W. Westervelt, Los Angeles, Cal. C. E. LeN. Arnold, formerly with the Inspiration Cons. Copper Co. at Inspiration, Ariz., has accepted a position with the Consolidated Arizona Smelting Co. at Mayer, Ariz.

Jan 1, 1919

By N. A. Gokcen, S. Fujishiro

THE pressures of Mn(g) in equilibrium with Mn7C3 and graphite have been measured by McCabe and Hudson' and Butler, McCabe, and paxton2 by means of graphite, zirconia, and Ta-Mo Knudsen cells. The details of corrections in their measurements were somewhat different from those of the authors;3'4 hence, further independent results at higher temperatures seemed to be warranted. The stoichiom-etry of Mn7C3 in equilibrium with graphite and its stability up to the vicinity of 1373 °K have been satisfactorily established by Kuo and persson5 (See also Hansen and Anderko).' The method of investigation has been described elsewhere in detail.3'4 The carbide was prepared in the manner described by McCabe and Hudson. In order to avoid possible reactions with refractory oxides, only graphite cells were used for the effusion experiments. The authors' results are the runs M-1, M-2 and M-3 listed in Table I, together with those of McCabe and co-workers. The heat capacity, c;, of Mn7C3 is not known; therefore McCable et al. plotted their data as log P vs 1/T and the results were only expressed first' as, and later2 as logP=- -14220+6.06 without further thermodynamic calculations. However, it is possible to estimate closely the necessary heat capacity as follows: When H; - &98 of CrC, or MnO, is plotted vs x, corresponding to various compounds, with temperature as the parameter, it is seen that the relationship is represented by a line of very small curvature. This relationship is also followed by other compounds which do not exhibit solid state phase transformations. In view of the fact that chromium and manganese have the atomic numbers of 24 and 25 respectively, it is reasonable to assume that H; - H;ae vs x for MnC, follows the same type of lines as those for CrC, for which adequate data are available.7 Similar correlations appear to be valid for oxides of two neighboring metals for which reliable data are available. The procedure is thus to move the lines for CrC, vertically (parallel to the axis of HT - H298) until they coincide with the points for MnC1/3, the only carbide of manganese whose H; - HO298 has been

Jan 1, 1963

By W. D. Brown

Newell1 has shown that hydrogen is removed from steel in a vacuum at a temperature of 500° to 900° C. within 136 hr. Holm and Thompson2 also state that, especially when the hydrogen is high, the results obtained by extraction at 800°C. agree with those obtained by vacuum fusion. In this laboratory, an apparatus was designed (Oct. 1940) and used wherein the piece of steel was heated at 100°F. in a Torricellian vacuum (Fig. I). This vacuum was produced by raising and lowering a "leveling bottle or bulb" containing mercury. Extensive tests were made with this apparatus. The weakness of the procedure was the possibility of leakage of air into the tube around the rubber stopper at the bottom. The present plan is to raise and lower the mercury by applying vacuum from a mechanical pump, to the top of the tube and then to a bottle of mercury in which the bottom of the tube is immersed. The Apparatus The extraction is made in a Pyrex tube A, I in. i.d. It is drawn down at the top at N and an 8-mm. i.d. tube is welded on it. To this a Pyrex stopcock E, 4-mm. bore, is welded. The tube between N and E is preferably 8 in. long and is graduated in milliliters. The total length of A to the stopcock is 28 inches. Heat is supplied by a split-tube furnace. 0 in. long by 6 in. in diameter, hinged on the side. A short pyrometer couple P is inserted through the walls of the furnace. In use this is standardized by comparison with a standard couple in a I-in. tube, just opposite this short couple. In the I-in. tube A a glass rod R, flattened at one end, supports the sample S and the length of R is so adjusted that the sample is in proper place. (It may float in the mercury.) The tube A is inserted in a large rubber stopper to fit the bottle B and extends nearly to the bottom. It is so placed that the handle of the stopcock faces the operator. In this stopper also is a short tube D bent at right angles for the application of vacuum. Also in this stopper is an 8-mm. tube C reaching nearly to the bottom; this is bent so as to miss the heater and again bent to bring it in line with and as near as possible to the upper and reduced part of tube A. On this tube C is welded a 4-mm.-bore stopcock H. In order that the two tubes may be as near as possible, the handle of stopcock H faces the back, or is the reverse of stopcock E. The total height of II above the bottom is 28 in. As explained later, this is the pressure-measuring tube C. The bottle B is about half full of mercury. The mercury must cover the ends of A and C by about I in. when they are evacuated. By tees T and rubber tubing RT the tubes A, C and D, the latter through the three-way stopcock M, are connected to the vacuum pump. A sheet of asbestos at K prevents the stopcocks E and H from becoming so hot that they leak. A good grade of vacuum lubricant prevents leakage of E and H. In order to measure the pressure of the

Jan 1, 1945

By C. H. Mathewson, A. U. Seybolt

As is well known, many questions affecting the properties and uses of a metal cannot be answered without careful consideration of the state of purity realized in the various operations of preparation, refining, or special treatment that have brought the product to its final state. The occurrellce of an impurity in minute quantity offers no guarantee that its effect will be inconsiderable because dissolved substances often modify the properties of a metal quite out of proportion to their concentration. In such cases the determination of solid solubility must be accepted as a problem of considerable difficulty, requiring the use of especially purified materials and methods not ordinarily used in the metallurgical laboratory. This aspect of the equilibrium between metals and their oxides is especially important and a search for fundamental data reveals little except conflicting opinion even concerning the systems of common occurrence and interest. Rhines and Mathewson1 in 1934 studied the solubility of oxygen in solid copper by annealing to equilibrium in air and gave reasons for the failure of other methods, notably the ordinary procedure of heat-treatment followed by microscopic examination, to yield reliable results. In this paper, a similar study has been made of the solubility of oxygen in cobalt. The simple theory of this method is outlined below. Conditions of Equilibrium between a Metal and Dissolved Oxide at Different Temperatures and Pressures The general conditions of equilibrium in any system are conveniently summarized in a projection of the triple curves of the P, T, X space

Jan 1, 1935

By A. U. Seybolt, C. H. Mathewson

As is well known, many questions affecting the properties and uses of a metal cannot be answered without careful consideration of the state of purity realized in the various operations of preparation, refining, or special treatment that have brought the product to its final state. The occurrellce of an impurity in minute quantity offers no guarantee that its effect will be inconsiderable because dissolved substances often modify the properties of a metal quite out of proportion to their concentration. In such cases the determination of solid solubility must be accepted as a problem of considerable difficulty, requiring the use of especially purified materials and methods not ordinarily used in the metallurgical laboratory. This aspect of the equilibrium between metals and their oxides is especially important and a search for fundamental data reveals little except conflicting opinion even concerning the systems of common occurrence and interest. Rhines and Mathewson1 in 1934 studied the solubility of oxygen in solid copper by annealing to equilibrium in air and gave reasons for the failure of other methods, notably the ordinary procedure of heat-treatment followed by microscopic examination, to yield reliable results. In this paper, a similar study has been made of the solubility of oxygen in cobalt. The simple theory of this method is outlined below. Conditions of Equilibrium between a Metal and Dissolved Oxide at Different Temperatures and Pressures The general conditions of equilibrium in any system are conveniently summarized in a projection of the triple curves of the P, T, X space

Jan 1, 1935

By C. E. Williams

THE Iron and Steel Division, A.I.M.E., is unique in this country in that it serves all phases of the iron and steel industries. Through its publications, its meetings, and its sponsorship of new technical developments in the industries, it has proved of great value. The various technical committees of the Division are the nucleus around which this service can be developed. The Blast Furnace and Raw Materials Committee has done excellent work. The need for beneficiation of iron ores is increasing and the economics of this operation are developing more and more in favor of increased activities. Ores that are slightly undergrade should be concentrated up to grade to supplant the present practice of mixing with higher-grade ores to bring up the average composition. Marginal ores that are not now being mined, or that are being mined and piled for future use, should be concentrated. The development of the use of sinter in the blast furnace, because of the elimination of fines, the advantage of better sizing of the charge, the resulting reduction of coke consumption, and increased output of pig iron per furnace, will make concentration and sintering become practical ahead of its natural time.

Jan 1, 1936

By J. C. Bradley

The relation of annealing temperature to conductivity of copper wire has been determined. Conductivity hard was 98.26 per cent. After a 10-min. heat,ing at 200" C. it was 98.69. By annealing 10 min. at 300" C. a large increase, to 100.93, occurred. Maximum conductivity, 101.15, was attained after a 500" C. anneal; thereafter it decreased to 100.53 after a 950" C. anneal. If copper is gassed the decrease is much more than this. Material and Method The work was done on high grade electrolytic copper, 99.942 per cent, copper plus silver, silver 0.0008 per cent. It was hot-rolled to 1/4 in., then cold drawn to 0.080 in. The wire was cut into 25 5-ft. lengths and numbered 1 to 25 as cut. Four samples were tested hard. The others were wound into 5-in. diameter coils. For the 100" C. heating a coil was put into water, the water brought to . boiling, and the wire kept at this temperature for 10 min. For the higher temperatures the coils were placed in envelopes of sheet copper, a little water added, and the envelopes sealed by folding over the edges twice, and hammering them together. This kept the air out very well. The envelope and wire were brought to the desired temperature; this was maintained for 10 min., then the whole was water-quenched. Results Data from the tests are shown in the table and plot (see Fig. 1); conductivity is referred to the International Annealed Copper Standard at 20" C. Conductivity hard is considerably less than conductivity soft.1 The increase is sharp when the wire anneals. The maximum, 101.15 per cent, in the particular material used, comes at 500º C.; thereafter the conductivity falls to 100.53 per cent. after 950" C. annealing, a drop of 0.62 per cent.

Jan 1, 1927

By E. von Maltitz

IN his highly interesting paper on "Piping and Segregation in Steel Ingots,"1 Prof. Howe emphasizes the effect of successive phases of internal pressure in the ingot in the evolution of gas, and the consequent formation of blow-holes. From his statements in other places, it may be inferred that he does not here intend to ignore the other variable factor, temperature, but rather to discuss this one more particularly. At all events, it is my purpose not to engage in controversy with Prof. Howe, but rather to contribute, towards the complete elucidation of this important subject which we all desire, my own views and experience. If, in doing so, I specially emphasize other factors than pressure, I need not be understood as denying what I do not think it necessary to discuss fully. Nor, in presenting my own original conclusions, need I be understood as claiming to be the first who ever reached or announced them. Many things are asserted or suggested upon inconclusive evidence; and to confirm such tentative propositions may be as valuable a service as to overthrow them. In the following passage, Prof. Howe adduces analogies, based upon the behavior of charcoal and of water, respectively, which seem to me questionable "In general, the. solvent power falls as the pressure falls ; and in general it rises as the temperature falls. Thus, to heat a solid, for instance charcoal, may expel part of its dissolved gas ; and a tumbler of water drawn cold from the faucet gradually evolves gas, as it stands and warms up on the sideboard." (p. 238.) Charcoal is a solid body, which has the property not only of absorbing gases in large quantities, but also of expelling the thus absorbed gases upon heating. A comparison between charcoal and iron as to the absorption of gases is scientifically not possible ; the gas-content of charcoal is partly due to the

Sep 1, 1907

By James J. Scott, John J. Reed

In a year fraught with difficulties, especially to small operators, the more stable mining organizations have shown a dynamic readiness to plunge ahead in the development of new mines, new and ingenious equipment and new tools for management to take the guesswork out of important decisions. New Mining Equipment The mining equipment display at the American Mining Congress in San Francisco demonstrated some rather radical new design concepts and a new willingness to use imagination to come up with ingenious new applications and adaptations of standard equipment.

Jan 2, 1963

By Arthur B. Foote

THE ball mill has superseded stamps for the reduction of gold ores in most of the recently designed plants, partly because stamps are not suited to die fine grinding required for flotation, and partly to save space and construction cost. Experience with these new mills seems to confirm the idea that it is more difficult to recover bold from a ball-mill product than it is when stamps are used for crushing. Microscopical examination of particles of gold that have passed through a ball mill show that the gold has been pounded into exceedingly thin flakes coated with a talcy surface, making it more difficult to save by amalgamation, flotation, or concentrating. Bearing in mind that gold is extremely malleable, it seems reasonable that this should be so. Contrast the action in a stamp battery, where the crushing is by impact in the presence of mercury, to the grinding and rolling under pressure in a ball mill. It is well known that a better recovery can be obtained by panning or amalgamation from a sample of ore that has been crushed by mortar and pestle than from one reduced on a bucking board.

Jan 1, 1937

October 16th, 1872. THE Institute assembled on Wednesday evening at the Western University, and was called to order by President Raymond. Mr. James Park, Jr., of Pittsburgh, made the address of welcome, which was responded to by President Raymond. The Council reported the following names, with approval, for election Ashburner, William, - San Francisco, Cal. Asmus, George, - New York. Baillie, Nathaniel, - Uniontown, Pa. Bowie, A. J., Jr. - San Francisco, Cal. Brown, A. J., - Treasure City, Nev. Butler, J. G., Jr., - Youngstown, Ohio. Chamberlin, J. G., - Leetonia, Ohio. Clark, R. Neilson, - Canyon City, Colorado. Cornell, A. B., - Youngstown, Ohio. De Crano, E. G., - San Francisco, Cal. Engelmann, H., - Salt Lake City, Utah. Faber du Faur, A., - New York. Janin, Louis, Jr., - San Francisco, Cal. Johnson, George J., - Salt Lake City, Utah.. Kent, Joseph C., - Phillipsburgh, N. J. Kent, William St. G., - Phillipsburgh, N. J. Liebenau, Charles von, - Silver City, Idaho. McClintock, A. H., - Wilkes-Barre, Pa. Miller, Thomas N., - Pittsburgh, Pa. Millholland, James A., - Mount Savage, Md. Peters, Ed. D., Jr., - Dudley, Colorado. Reese, Jacob, - Pittsburgh; Pa. Schirmer, J. F. L., - Denver, Colorado. Smith, W. S., - Fairplay, Colorado. Stoelting, Hermann, - Georgetown, Colorado. Sweet, W. A., - Syracuse, N. Y. Tripple, Alexander, - New York. Van Arsdale, W. H., - Swansea, Cal. Willard, Dwight D., - Bordentown, N. J. The following resolution was then offered and passed Resolved, That gentlemen present, not members, be invited to take part in the discussions of the Institute at the various sessions of the present meeting.

Jan 1, 1873

TEE Institute assembled on Wednesday evening at the Western University, and was called to order by President Raymond. Mr. James Park, Jr., of Pittsburgh, made the address of welcome, which was responded to by President Raymond. The Council reported the following names, with approval, for election : Ashburner, William, . . . . . San Francisco, Cal. Asmus, George, . . . . . . New York. Baillie, Nathaniel, . . . . . Uniontown, Pa. Bowie, A. J., Jr., . . . . . San Francisco, Gal. Brown, A. J., . . . . . . Treasure City, Nev. Butler, J. G., Jr., . . . . . Youngstown, Ohio. Chamberlin, J. G., . . . . . Leetonia, Ohio. Clark, R. Neileon, . . . . . Canyon City, Colorado. Cornell, A. B., . , . . . . Youngstown, Ohio. De Crano, E. C., . . . . . San Francisco, Cal. Engelmann, H., . . . . . . Salt Lake City, Utah. Faber du Faur, A., . , . . . New York. Janin, Louie, Jr., . . . . . San Francisco, Cal. Johnson, George J., . . . . . Salt Lake City, Utah., Kent, Joseph C., . . . . . Phillipsburgh, N. J. Kent, William St. G., . . . . Phillipsburgh, N. J. Liebenau, Charles von, . . . . Silver City, Idaho. McClintock, A. H., . . . . . Wilkes-Barre, Pa. Miller, Thomas N., . . . . . Pittsburgh, Pa. Millholland, James A., , . . . Mount Savage, Md. Peters, Ed. D., Jr., . . . . . Dudley, Colorado. Reese, Jacob, . . . . . . Pittsburgh, Pa. Schirmer, J. F. L., . . . . . Denver, Colorado. Smith, W. S., . . . . . . Fairplay, Colorado. Stoelting, Hermann, . . . . . Georgetown, Colorado. Sweet, W. A., . . . . . . Syracuse, N. Y. Tripple, Alexander, . . . . . New York. Van Arsdale, W. H., . . . . . Swansea, Cal. Willard, Dwight D., . . . . . Bordentown, N. J. The following resolution was then offered and passed : Resolved, That gentlemen present, not members, be invited to take part in the discussions of the Institute at the various sessions of the present meeting.