Search Documents

By Joseph Hodgson

Introduction SINCE about 70 per cent. of the total cost of mining is due to underground work which is out of sight, it is essential that expenditures should be made here to the best advantage. A great many mistakes have been made which were expensive, but perhaps these have not even been detected by mine owners. In the future these may be minimized to some extent, especially if there is cooperative effort on the part of each employee. I have been interested in this subject for some years and have tried to deduce principles and methods. These have proved highly advantageous and may also be of help to others. Some corporations, like the United States Steel, and the Cleveland-Cliffs Iron Co., have done a great deal in this field by having stated meetings of their organizations, with the view to interchanging ideas among their men and educating them along the lines of concerted effort. Since no man knows all about the various branches of mining, it is advisable that frequent meetings of the operating department be held for the interchange of ideas and that all members of the organization have an opportunity to express themselves on the various subjects. It has often been found that in discussions between heads of departments, foremen and bosses, many valuable suggestions may be obtained which promote the best interests of the company. The method regarded as the most conducive to cooperative effort, and pursued by the organization, is to analyze and develope the different phases of various mining subjects at regular meetings.

Jan 5, 1916

By Irving Cadoff, Jack Medoff

THE linear thermal expansions of oriented single crystals of zinc were measured in the range from 20" to 416°C using a Leitz HTV optical lever differential dilatometer. The single crystals, supplied by Dr. J. J. Gilman, General Electric Research Laboratory, Schenectady, N.Y., were prepared from 99.999 pct-purity zinc, and were in the form of rods approximately 2 in. long by 0.15 in. in diameter having the following orientations: x = 1.5, 12, 20, 30, 37.5, 49, 60, 73, and 82 deg where x is the angle between the specimen axis and the (0001) plane of the crystal. From the family of expansion vs temperature curves, the instantaneous expansion coefficients were calculated at 100°C intervals, and Fig. 1 shows a plot of these derived coefficients for each orientation. Coefficients were obtained from the raw data using the chord-slope method. The curves in Fig. 1 indicate a positive temperature coefficient for low x, a negative temperature coefficient for high X, and an expansion coefficient invariant with temperature, amounting to about 43 x 106, for a crystal orientation of approximately 52 deg. From the available data, it is possible to arrive at the values for the axial thermal-expansion coef- ficients a, and a, by extrapolating the curve of the expansion coefficient vs orientation to zero and 90 deg orientations. More precise values for a, and a, are obtained if the instantaneous coefficients are plotted against the square of the cosine of the orientation angle, as shown in Fig. 2. The extrapolated terminal points of the best straight line through the data points of such a plot define the axial coefficients at that temperature. The theoretical justification for the linearity of this curve comes from inspection of a rearranged form of the general anisotropic equation for expansion: ax=a, + (a, -a,)cosZx [1I in which a, is the expansion coefficient in the "c" or [0001] direction and a, the expansion coefficient in the "a" or [ll50] direction. From Fig. 2, the axial coefficients at 100°C, for example, were found to be a, = 13.9 x 10'6 and a, = 62.4 x 10"6 per "C. In the same way, the coefficients were determined for 20", 200°, 300°, and 400°C. This data is summarized in Fig. 3. It is of interest to observe the common intersection of the curves in Fig. 3, which seems to bear out the earlier observation, from Fig. 1, of a

Jan 1, 1964

By Ferit Gurses

Extensive coal and lignite deposits exist in Turkey. Bituminous coal is the nation's principal mineral resource; important not only as fuel for the industrial development of the country, but also as a means of obtaining foreign exchange. Of the electrical power generated during 1939, 82.8 per cent was derived from coal.' It is anticipated that the lignite deposits will be one of the major sources of power for the electrification of the country. Bituminous Coal The locations of the four principal bituminous-coal2 basins are indicated on Fig. 1. The Eregli-Zonguldak basin lies on the Black Sea northwest of Ankara; the Canakkale basin lies near the junction of the Dardannelles; the Trakya basin is in European Turkey northwest of the Bosphorus and the Erzurum basin lies far to the east. The Eregli-Zonguldak basin is the most important of the four. This coal basin was discovered in 1829 but did not arouse interest until 1848; up to 1865, its annual production had not exceeded 50,000 metric tons. In 1865, during the Sultanate, working of coal mines was started by the Navy department, and the annual production was 61,145 metric tons. In 1908, the Minister of Commerce and Agriculture was authorized to develop the whole coal basin. Production reached 264,397 metric tons in 1910, and during 1915-1922, preceding the revolution, the total produc- tion of the basin was' 2,676,043, or an average of 334,000 metric tons annually. The period of national revolution that followed was marked by a steady increase in coal production in Turkey, although world production decreased, because of the crisis of 1929-1932, about 52 per cent. ARea and Geology of the Coal Basin The geology of the Eregli-Zonguldak area is not yet completely known. The basin begins -at Gungazi, to the west of Eregli, and extends to Sogutozu, a distance of about 106 miles. The coal beds, however, appear only in places and the overlying Cretaceous strata hide them elsewhere. This area includes the most important centers, such as Kandilli, Alacaagzi, Teflenli, Kozlu, Gelik (see Fig. 2). The geological sequence of the district is correlated with the Cretaceous of the Balkans; which is, in turn, a prolongation of the Alpine zone. Geological surveys made by G. Ralli, R. Zeiller and P. Arni3 show that the Eregli-Zonguldak formations fall into three natural divisions. Series a, The Alacaagzi in the district of that name (Fig. 2), is of the Culm stage. The strata strike generally east-west and dip about 30" south. This series appears also around Kandilli and Camli, with a steeper angle of dip, but the deposits there lack regularity. The Alacaagzi stage appears also farther east, to the south of Kozlu and Gelik. The Alacaagzi series contains 15 seams of an average thickness of 2 ft. of good coal. Series b, the Kozlu, best represented in Zonguldak, Kilimli, Catalagzi, and between

Jan 1, 1944

By Ferit Gurses

Extensive coal and lignite deposits exist in Turkey. Bituminous coal is the nation's principal mineral resource; important not only as fuel for the industrial development of the country, but also as a means of obtaining foreign exchange. Of the electrical power generated during 1939, 82.8 per cent was derived from coal.' It is anticipated that the lignite deposits will be one of the major sources of power for the electrification of the country. Bituminous Coal The locations of the four principal bituminous-coal2 basins are indicated on Fig. 1. The Eregli-Zonguldak basin lies on the Black Sea northwest of Ankara; the Canakkale basin lies near the junction of the Dardannelles; the Trakya basin is in European Turkey northwest of the Bosphorus and the Erzurum basin lies far to the east. The Eregli-Zonguldak basin is the most important of the four. This coal basin was discovered in 1829 but did not arouse interest until 1848; up to 1865, its annual production had not exceeded 50,000 metric tons. In 1865, during the Sultanate, working of coal mines was started by the Navy department, and the annual production was 61,145 metric tons. In 1908, the Minister of Commerce and Agriculture was authorized to develop the whole coal basin. Production reached 264,397 metric tons in 1910, and during 1915-1922, preceding the revolution, the total produc- tion of the basin was' 2,676,043, or an average of 334,000 metric tons annually. The period of national revolution that followed was marked by a steady increase in coal production in Turkey, although world production decreased, because of the crisis of 1929-1932, about 52 per cent. ARea and Geology of the Coal Basin The geology of the Eregli-Zonguldak area is not yet completely known. The basin begins -at Gungazi, to the west of Eregli, and extends to Sogutozu, a distance of about 106 miles. The coal beds, however, appear only in places and the overlying Cretaceous strata hide them elsewhere. This area includes the most important centers, such as Kandilli, Alacaagzi, Teflenli, Kozlu, Gelik (see Fig. 2). The geological sequence of the district is correlated with the Cretaceous of the Balkans; which is, in turn, a prolongation of the Alpine zone. Geological surveys made by G. Ralli, R. Zeiller and P. Arni3 show that the Eregli-Zonguldak formations fall into three natural divisions. Series a, The Alacaagzi in the district of that name (Fig. 2), is of the Culm stage. The strata strike generally east-west and dip about 30" south. This series appears also around Kandilli and Camli, with a steeper angle of dip, but the deposits there lack regularity. The Alacaagzi stage appears also farther east, to the south of Kozlu and Gelik. The Alacaagzi series contains 15 seams of an average thickness of 2 ft. of good coal. Series b, the Kozlu, best represented in Zonguldak, Kilimli, Catalagzi, and between

Jan 1, 1944

By Ferit Gurses

EXTENSIVE coal and lignite deposits exist in Turkey. Bituminous coal is the nation's principal mineral resource; important not only as fuel for the industrial development of the country, but also as a means of obtaining foreign exchange. Of the electrical power generated during 1939, 82.8 per cent was derived from coal.1 It is anticipated that the lignite deposits will be one of the major sources of power for the electrification of the country. BITUMINOUS COAL The locations of the four principal bituminous-coal2 basins are indicated on Fig. 1. The Eregli-Zonguldak basin lies on the Black Sea northwest of Ankara; the Canakkale basin lies near the junction of the Dardannelles; the Trakya basin is in European Turkey northwest of the Bosphorus and the Erzurum basin lies far to the east. The Eregli-Zonguldak basin is the most important of the four. This coal basin was discovered in 1829 but did not arouse interest until 1848; up to 1865, its annual production had not exceeded 50,000 metric tons. In 1865, during the Sultanate, working of coal mines was started by the Navy department, and the annual production was 61,145 metric tons. In 1908, the Minister of Commerce and Agriculture was authorized to develop the whole coal basin. Production reached 264,397 metric tons in 1910, and during 1915-1922, preceding the revolution, the total production of the basin was 2,676,043, or an average of 334,000 metric tons annually. The period of national revolution that followed was marked by a steady increase in coal production in Turkey, although world production decreased, because of the crisis of 1929-1932, about 52 per cent. AREA AND GEOLOGY OF THE COAL BASIN The geology of the Eregli-Zonguldak area is not yet completely known. The basin begins at Gungazi, to the west of Eregli, and extends to Sogutozu, a distance of about 106 miles. The coal beds, however, appear only in places and the overlying Cretaceous strata hide them elsewhere. This area includes the most important centers, such as Kandilli, Alacaagzi, Teflenli, Kozlu, Gelik (see Fig. 2). The geological sequence of the district is correlated with the Cretaceous of the Balkans; which is, in turn, a prolongation of the Alpine zone. Geological surveys made by G. Ralli, R. Zeiller and P. Arni3 show that the Eregli-Zonguldak formations fall into three natural divisions. Series a, The Alacaagzi in the district of that name (Fig. 2), is of the Culm stage. The strata strike generally east-west and dip about 30° south. This series appears also around Kandilli and Camli, with a steeper angle of dip, but the deposits there lack regularity. The Alacaagzi stage appears also farther east, to the south of Kozlu and Gelik. The Alacaagzi series contains 15 seams of an average thickness of 2 ½ ft. of good coal. Series b, the Kozlu, best represented in Zonguldak, Kilimli, Catalagzi, and between

Jan 1, 1944

By E. C. Skinner

Cardox, which consists essentially of a steel tube containing carbon dioxide compressed to the liquid state, is a trade name designating a device used principally in coal mines to break down coal. The use of Cardox to break down coal was developed in the Middle Western coal fields around 1927 or 1928. At first, a large, heavy tube was used, requiring many parts. Through experimentation and technologic improvement, the weight of the tube has been brought down from 88 lb. to 20 lb. and the new, light tube makes use of larger volumes of CO2 at lower pressures than formerly was thought possible. This blasting method is extensively used today in coal mines and probably one tenth of the bituminous coal produced in the United States is prepared with Cardox. Construction and Application As used in the coal mine, Cardox looks like a piece of steel pipe 2 to 3 in. in diameter and 3 to 5 ft. long. When it is necessary to fire a shot, the tube is wired with two leg wires that are long enough so that when the tube is pushed the desired distance into the hole the wires will protrude 5 to 6 in. It has been found that No. 18 insulated copper annunciator wire is the best material for leg wires. A two-conductor rubber-covered shot-firing cable of sufficient length is then attached to the leg wires. A 2 to 6-volt current is applied, either by means of shot-firing batteries or the standard type of shot-firing generator. Upon the application of the current, the charge in the cartridge is set off. Because the breaking action upon the coal is supplied by the relatively slow physical expansion of the carbon dioxide gas rather than by the rapid chemical formation of gases as in more familiar explosives, the result is a slow heaving action, somewhat similar to that produced by black powder, rather than a shap detonating effect. Permissible powder does its work at roughly ten times the pressures in use with Cardox. The escaped gas from a Cardox shot apparently works along the planes of weakness in the coal face, such as the coal cleats, the edges of the cut, and along the top of the seam, breaking off the coal toward the free faces and heaving the mass of coal outward. Cardox tubes are manufactured in various sizes to take care of variable conditions of seam size, undercut depth, cleatage, coal hardness, and so forth. The tubes range in diameter from 2 to 3 in. (Table I) and the normal CO2 charge is from 24 to 96 oz. For any one tube size, several sizes of shear disks are available, thus excellent control of the type of shooting desired is possible. In general, local experience and experimentation dictate the size of tube chosen for any particular job. For high coal, and deeper or wider cuts, a larger size is chosen to start with, and the opposite is true for low coal, softer coal, or small cuts. After the tube size has been experimentally selected, tests are run in the mine to determine how many shot holes are needed and where the holes should be placed. The size of the disk,

Jan 1, 1944

By E. C. Skinner

Cardox, which consists essentially of a steel tube containing carbon dioxide compressed to the liquid state, is a trade name designating a device used principally in coal mines to break down coal. The use of Cardox to break down coal was developed in the Middle Western coal fields around 1927 or 1928. At first, a large, heavy tube was used, requiring many parts. Through experimentation and technologic improvement, the weight of the tube has been brought down from 88 lb. to 20 lb. and the new, light tube makes use of larger volumes of CO2 at lower pressures than formerly was thought possible. This blasting method is extensively used today in coal mines and probably one tenth of the bituminous coal produced in the United States is prepared with Cardox. Construction and Application As used in the coal mine, Cardox looks like a piece of steel pipe 2 to 3 in. in diameter and 3 to 5 ft. long. When it is necessary to fire a shot, the tube is wired with two leg wires that are long enough so that when the tube is pushed the desired distance into the hole the wires will protrude 5 to 6 in. It has been found that No. 18 insulated copper annunciator wire is the best material for leg wires. A two-conductor rubber-covered shot-firing cable of sufficient length is then attached to the leg wires. A 2 to 6-volt current is applied, either by means of shot-firing batteries or the standard type of shot-firing generator. Upon the application of the current, the charge in the cartridge is set off. Because the breaking action upon the coal is supplied by the relatively slow physical expansion of the carbon dioxide gas rather than by the rapid chemical formation of gases as in more familiar explosives, the result is a slow heaving action, somewhat similar to that produced by black powder, rather than a shap detonating effect. Permissible powder does its work at roughly ten times the pressures in use with Cardox. The escaped gas from a Cardox shot apparently works along the planes of weakness in the coal face, such as the coal cleats, the edges of the cut, and along the top of the seam, breaking off the coal toward the free faces and heaving the mass of coal outward. Cardox tubes are manufactured in various sizes to take care of variable conditions of seam size, undercut depth, cleatage, coal hardness, and so forth. The tubes range in diameter from 2 to 3 in. (Table I) and the normal CO2 charge is from 24 to 96 oz. For any one tube size, several sizes of shear disks are available, thus excellent control of the type of shooting desired is possible. In general, local experience and experimentation dictate the size of tube chosen for any particular job. For high coal, and deeper or wider cuts, a larger size is chosen to start with, and the opposite is true for low coal, softer coal, or small cuts. After the tube size has been experimentally selected, tests are run in the mine to determine how many shot holes are needed and where the holes should be placed. The size of the disk,

Jan 1, 1944

By A. D. Rich

The term "bleaching clay" or "bleaching earth," as used in the oil industries, refers to clays that in their natural state, or after chemical or physical activation, have the capacity for adsorbing coloring matter from oil. There are three common types of bleaching clays: fuller's earth, activated clays, and activated bauxite. Fuller's earth, or naturally active clay, is prepared from bentonites (see Chap. 5) that possess natural activity. It is not activated commercially; in fact, earths of this type ordinarily do not respond satisfactorily to acid activation. Fuller's earth is prepared in pulverized as well as granular form for use in the contacting and percolation processes, respectively. Acid-activated clays also are of bentonitic origin. The basic raw clay, however, is of a type that has a very low natural activity but is highly activable by treatment with mineral acid. Commercial acid-activated clays generally possess several times the decolorizing power (bleaching efficiency) of the best quality of fuller's earth. The former are prepared commercially only in the pulverized grade because of the difficulties in obtaining a satisfactory granular product, and hence are used only in the contact process. Activated bauxite is made by heat-treating bauxite ore, which in its natural state has very little natural activity. The commercial product is prepared in granular form for use in the percolation process on petroleum oils. For the most part, bleaching clay is used commercially in the decolorization of animal, vegetable and petroleum oils, fats and waxes. It is applied in two ways: (1) by the percolation method and (2) by the contacting method. Percolation refers to the passage of oil through a bed of granular clay whereas contacting refers to direct agitation of oil and pulverized clay followed by removal of the clay from the oil by filtration. In either case, the decolorizing effect is obtained by intimate contact between the liquid oil and the solid adsorbent. Petroleum oils are treated commercially by either the percolation or the contact process. Animal and vegetable oils are treated by the contact process only. Composition The raw clays from which both fuller's earth and acid-activated clays are prepared are composed of hydrous aluminum silicates containing varying quantities of magnesium, iron, calcium and other elements. These raw materials are usually nonswelling bentonites derived from volcanic ash or lava by weathering and hydrothermal chemical reactions. The bentonites have as their chief mineral constituent montmorillonite, which has the formula [(OH)4Si6A14O20•nH2O], according to Grim. (See Chap. 5, ref. 6, p. 91.) The underlying reasons are not fully known for the natural activity of the fuller's earth type of clay and its usual failure to further activate with mineral acid in contrast to the natural inactivity of the activatable type of clay. However, it may be said that the bentonites that are responsive to the acid-activation treatment generally have not undergone any drastic metamorphism. The chemical composition is not a reliable means of discrimination between a nonactive, a naturally active, and a nonactive but activable clay, therefore it is not possible to forecast the ultimate quality of a clay on the basis of the raw-clay analysis alone. Table 1 gives typical analyses of representative clays of the foregoing classifications.

Jan 1, 1960

By Henry Faul

Measurement of radioactivity of rocks and ores has developed into a complete method of geophysical exploration. The problem falls into three natural categories: (1) surface radiation measurement in the field and underground; (2) radioactivity logging of drillholes; and (3) laboratory analysis of samples. Portable counters are used in the field for tracing radioactive formations and for quanti tative estimates of radioactive content of surface rock. Wartime advances in battery design make it possible to construct small precision counters that can be carried easily. Even the smallest conventional diamond drillholes can be logged, and actual content of the radioactive element can be measured. The exact grade of very thin active layers or veins can be estimated only approximately. Samples may be analyzed for their alpha, beta or gamma activity, and beta assaying is the best suited to rapid routine operation. Simple calibration with standard samples is sufficient for rough work, but a density correction is necessary when greater precision is required. Samples with high emanating power should be fixed and stored for three weeks to reestablish the radium-radon equilibrium prior to precision assaying. Carno-tite can be fixed by sintering or molding with plastics. Among the important new developments, a low-voltage Geiger tube has been 'designed recently, and crystal scintillation counters hold great promise for high-efficiency gamma-ray measurement. Introduction During the last few years we have witnessed an unprecedented rise in the demand for radioactive minerals, coming as a direct consequence of the discovery of nuclear fission and subsequent developments, the full impact of which is by no means in sight even now. It remains certain, however, that radioactive minerals, and especially those which can be used as ores of uranium and thorium, will continue to be of great interest not only to the prospector and mine operator but also to the various inspection parties envisioned by most of the schemes advanced for the control of nuclear energy on a world-wide basis. It is clear, therefore, that the measurement of radioactivity in rocks in the field as well as in samples in the laboratory has become a method of geophysical exploration of some importance. If we consider the recent technological advances in the general fields of nuclear physics and electronics it seems proper to review the present status of the methods and procedures of radiological exploration. General Considerations Equilibrium If we take a fixed amount of uranium that has just been purified, some of it will immediately start decaying into its first daughter element which in turn decays into its own daughter and so on down the line until the last daughter is reached—a stable isotope of lead. The rate at which a radioactive element decays is frequently expressed as the half-life, which is the length of time required for the decay of half the atoms in a given amount. The half-life is inversely proportional to the decay constanl X which is defined as the number of atoms which decay in one unit of time divided by

Jan 1, 1949

By Henry Faul

Measurement of radioactivity of rocks and ores has developed into a complete method of geophysical exploration. The problem falls into three natural categories: (1) surface radiation measurement in the field and underground; (2) radioactivity logging of drillholes; and (3) laboratory analysis of samples. Portable counters are used in the field for tracing radioactive formations and for quanti tative estimates of radioactive content of surface rock. Wartime advances in battery design make it possible to construct small precision counters that can be carried easily. Even the smallest conventional diamond drillholes can be logged, and actual content of the radioactive element can be measured. The exact grade of very thin active layers or veins can be estimated only approximately. Samples may be analyzed for their alpha, beta or gamma activity, and beta assaying is the best suited to rapid routine operation. Simple calibration with standard samples is sufficient for rough work, but a density correction is necessary when greater precision is required. Samples with high emanating power should be fixed and stored for three weeks to reestablish the radium-radon equilibrium prior to precision assaying. Carno-tite can be fixed by sintering or molding with plastics. Among the important new developments, a low-voltage Geiger tube has been 'designed recently, and crystal scintillation counters hold great promise for high-efficiency gamma-ray measurement. Introduction During the last few years we have witnessed an unprecedented rise in the demand for radioactive minerals, coming as a direct consequence of the discovery of nuclear fission and subsequent developments, the full impact of which is by no means in sight even now. It remains certain, however, that radioactive minerals, and especially those which can be used as ores of uranium and thorium, will continue to be of great interest not only to the prospector and mine operator but also to the various inspection parties envisioned by most of the schemes advanced for the control of nuclear energy on a world-wide basis. It is clear, therefore, that the measurement of radioactivity in rocks in the field as well as in samples in the laboratory has become a method of geophysical exploration of some importance. If we consider the recent technological advances in the general fields of nuclear physics and electronics it seems proper to review the present status of the methods and procedures of radiological exploration. General Considerations Equilibrium If we take a fixed amount of uranium that has just been purified, some of it will immediately start decaying into its first daughter element which in turn decays into its own daughter and so on down the line until the last daughter is reached—a stable isotope of lead. The rate at which a radioactive element decays is frequently expressed as the half-life, which is the length of time required for the decay of half the atoms in a given amount. The half-life is inversely proportional to the decay constanl X which is defined as the number of atoms which decay in one unit of time divided by

Jan 1, 1949

By D. L. Everhart

The search for new deposits raises two important questions: Where did the metallic ions that formed the orebodies come from? What processes and geologic factors were involved in ore replacement? A review of the wide geological variety of recent uranium discoveries tells how these questions are being answered. SOONER or later intelligent exploration for uranium leads to these questions: Where did the metallic ions that formed the orebodies come from? What processes and geologic factors were involved in ore replacement? These matters, of course, make a big difference in how best to look for orebodies. Before these questions are discussed it might be well to point out other factors bearing on the subject. The whole business of uranium exploration is only a little over ten years old, participation by the public is only about six years old, and real interest and activity by more than a few large mining companies has arisen only in the past two or three years. Throughout this short period, uranium exploration has been affected by the unique influences of necessary security measures and by division of the overall job into individual projects by a large number of specialists in diverse fields. This has meant that a normal interchange of information on the nature of uranium deposits has really only just begun. Compared to the vast amount of published studies on iron, copper, lead, zinc, and gold deposits over the past 50 to 75 years, current knowledge of uranium deposits is in its infancy and much of the pertinent information is still scattered about in a number of unpublished sources. The volume of reports on all phases of uranium exploration is now beginning to mount at a remarkable rate, and geologists with widely varying specialized backgrounds in uranium geology are engaging in spirited debates over the origin of uranium and the relative importance of geologic controls of various deposits. One of the most interesting features of known uranium deposits of the world is the wide variation, see Table I, in character and geologic environment. It should be noted that many types became prominent during 1953. The davidite-bearing veins of Radium Hill, South Australia, are almost unique, although the same mineral occurs in a different kind of deposit in Mozambique. Recent studies indicate that brannerite disseminated in the granite near Cracker's Well, South Australia, may soon constitute uranium ore. Basalt has been added to the list of favorable host rocks in the Northern Territory of Australia. Basalt is also the host of the pitchblende veins of the Martin Lake deposit, Beaverlodge district, Saskatchewan. The truly remarkable rich and extensive Steen deposit near Moab, Utah, is of the uraninite-vanadium oxide type. Secondary hydrous uranium arsenates and phosphates constitute the uranium minerals in the disseminated deposits of the Wind River Basin, Wyo., a new district discovered in the summer of 1953. Uranium minerals in shales adjacent to fractures were newly reported in New Mexico and several other parts of the world during the year. The well-known important uraninite dissemination in the Rand conglomerates of South Africa has a counterpart, as discovered in the summer of 1953, in the Mississagi quartzite and conglomerate of the Blind River district, Ontario. Gunnar deposit of the Lake Athabaska district, Saskatchewan, consists of uraninite in both granite and sedimentary gneiss beneath a granite cap, and large new orebody of the Eldorado Co. in the same general area follows a preferred stratigraphic horizon in schists. Uranium is, generally speaking, a very soluble and ubiquitous element. It occurs in at least two valency states and for this reason is not easily tied down in natural solutions. As Gruner' has pointed out, it is probable that uranium starts in the hexava-lent state in nearly all solutions instrumental in its transfer. It is believed that under oxidizing conditions the uranium moves in solution as the uranyl ion, UO. In solutions ranging in pH from 1 to 5, the uranyl ion is most commonly in association with

Jan 1, 1955

By R. B. Basham, C. W. Macune

Very small anomalies in oil well temperatures are detected and measured by recording the difference in temperature existing between two thermally sensitive elements which are Spaced several feet apart on a small diameter carrier and lowered into the bore hole. The elements operate in a balanced electrical circuit, sending only a reference signal to the surface as long as normal gradient temperatures are encountered. When either element enters a temperature disturbance, the circuit is unbalanced and produces large recorder deflections for minute anomalies. The system is highly sensitive to small changes in thermal gradients caused by gas or fluid movements and to the boundaries between beds of different thermal conductivities. Typical logs show successful applications of the process to locating gas and water leaks in casing, gas entry. and gas-oil contact. INTRODUCTION Temperature measurements in oil wells have been made for many years in the search for additional sub-surface data. It has been generally agreed that many conditions in the bore hole cause temperature anomalies which, if located and measured, could yield useful information. But it has been recognized also that many of the irregularities, such as those produced by small water and gas leaks in casing, might be very small and therefore difficult to detect with certainty.' Although tem-perature measurements have been made which show anomalies of less than one degree deviation from normal gradient temperatures, the results are usually uncertain and unconvincing. The general practice, therefore. has been to apply temperature surveys only to well conditions known to produce appreciable disturbances, such as large gas movements and cement hydration. The recent demand for additional data has focused attention on the problem of making dependable temperature measurements in the many instances when anomalies are small but none the less significant. It was for the purpose of detecting these minute irregularities in bore hole temperature that the program described in the following text was undertaken. It is emphasized that this presentation is not offered as a complete study, for the process is still partially experimental. But it is believed that the results obtained thus far will be of interest to the industry and will indicate some of the system's potential usefulness. DIFFERENTIAL MEASUREMENT The chief value of differential measurement lies in the fact that a difference between two factors can be measured with a scale of values best suited to that difference, a scale that might be cumbersome or impractical if applied to the factors themselves. When it is known that all factors will be nearly equal in value, and therefore the differences consistently small, it is possible to select a scale which will permit very accurate measurement of the differences. This advantage is in contrast to the difficulty of measuring small increments of a single variable, where the increment must be measured by a large scale which is suitable for measuring the entire factor. Gradient temperatures are usually measured under this latter condition where temperature measuring apparatus must have a scale extending over the range of expected temperatures, say 50' to 25O°F, and it becomes almost impossible to detect small irregularities of less than one degree. The use of large strip chart recorders and divided multiple ranges tend to amplify the small anomaly and make it more pronounced. But the instability of instruments, both

Jan 1, 1952

By T. A. Rickard

Do not write until you have something to say. Think first; then write. In order to be understood, you must know what you wish to say. Clear writing is the consequence of clear thinking. Therefore consider your subject well before you begin to write; ruminate on it; marshal the salient facts in your mind; saturate yourself with the ideas you wish to express and with cognate ideas; then express yourself deliberately. If you are bubbling over with your subject the words will come, but you might as well expect to sail without a breeze as hope to give life to words without the living thought. Here I may advert to the fact that among the uneducated it is a common expectation to acquire the knack of writing without taking the trouble to study the art of literature. I overheard a woman in a suburban train remark to her neighbor: "I'd like to be able to write well without stopping to think about it". She was one of many that would like to do a thing well without the trouble of thinking; but it cannot be done in respect of anything to which thought is essential. The possession of a good voice does not justify a person in expecting to sing successfully to a large audience; before singing in public one has to master the technique of singing; one has to learn first how to breathe properly, how to enunciate, and many other things. The successful singer is an artist, not a megaphone. Most of us would regard a man or a woman without any training in the art of singing as a fool or an impostor if he or she were to give a public concert, yet we do not recognize the equal foolishness and imposture of persons that write books before they have studied the technique of writing. That is why so many books are unreadable, and why many books by clever men are difficult to read. They start to write books before

Jan 1, 1931

By John Porter

(Cleveland Meeting, October, 1912.) Iv taking up this subject it is first necessary to define our terms. Efficiency, in its engineering usage, means the ratio between actual and theoretical results, and efficiency-records thus involve the use of scientifically determined standards with which all results are compared. Scientific management is the methods used in increasing efficiency, and includes the use of efficiency-records. Effeciency-records do not alone constitute scientific management, but they are necessary to it, and any so-called system of management which is not based upon standards and standardization is fundamentally wrong. An efficient management and efficiency-methods in management are not the same thing. There are some people who have an instinctive genius for management and accomplish results without exactly knowing how they do it. Such a manager may obtain a very high efficiency without the aid of scientifically determined standards. On the other hand, it sometimes happens that poor results will accompany the use of efficiency-records, clue to a weak or indifferent management, which fails to make use of the information acquired. Efficiency-records are only a tool, and like other tools are worthless unless used. The ordinary cost, sheet and production-statement do not go far enough. They tell what has been done, but give no information as to how well it has been done. It is true that the man who is familiar with the industry and the plant in question may draw inferences and form a general idea of good work or bad work, but it can only be a very general and hazy idea. Comparisons with previous records or records of other plants are unsatisfactory, since there is nothing to show the cause of the differences.

Jan 4, 1913

By John Jermain Porter

In taking up this subject it is first necessary to define our terms. Efficiency, in its engineering usage, means the ratio between actual and theoretical results, and efficiency-records thus involve the use of scientifically determined standards with which all results are compared. Scientific management is the methods used in increasing efficiency, and includes the use of efficiency-records. Efficiencj-records do not alone constitute scientific management, but they are necessary to it, and any so-called system of management which is not based upon standards and standardization is fundamentally wrong. An efficient management and efficiency-methods in management are not the same thing. There are some people who have an instinctive genius for management and accomplish results without exactly knowing how they do it. Such a manager may obtain a very high efficiency without the aid of scientifically determined standards. On the other hand, it sometimes happens that poor results will accompany the use of efficiency-recorcis, due to a weak or indifferent management, which fails to make use of the information acquired. Efficiency-records are only a tool, and like other tools are worthless unless used. The ordinary cost-sheet and production-statement do not go far enough. They tell what has been done, but give no information as to how well it has been done. It is true that the man who is familiar with the industry and the plant in question may draw inferences and form a general idea of good work or bad work, but it can only be a very general and hazy idea. Comparisons with previous records or records of other plants are unsatisfactory, since there is nothing to show the cause of the differences. Efficiency-records supply this need. They compare actual

Jan 1, 1913

By Sherwin F. Kelly, Bela Low, William B. Creagmile

Electrical methods and instruments for geophysical exploration have been almost exclusively applied, during these years of development of the art, by a few companies specializing in this field. The control of patents, the cost of the instruments and the general lack of published information on details of field procedure and office interpretation have given these owners a monopoly in carrying out electrical surveys. The development of the Megger Ground Tester1 seems likely to change this situation, and to enable mining engineers and geologists, without special training in geophysics, to carry out simple reconnaissance electrical surveys. Nevertheless, the need for such special training and experience in planning surveys and interpreting their results remains, and probably i always will remain, indispensable for a successful outcome. The unique thing about, the Megger Ground Tester, which gives rise to this hope for its general use, is its simplicity of operation. The four binding posts of the instrument are connected by insulated wires to four stakes driven into the ground at appropriate points. The crank of the Megger is then turned, and the resistance of the ground between the two inside stakes is read directly, in ohms, by the deflection of a pointer over a scale. The apparatus is shown in Fig. 1. Fundamentally, the principle of operation is that of determining the resistance of a four-terminal conductor, as applied by Frank Wenner to the measurement of earth resistivity. "A four-terminal conductor is a conductor provided with two terminals to which current leads may be connected and two terminals to which potential leads may be connected. The resistance of such a conductor is the difference in potential between the potential terminals divided by the current entering and leaving

Jan 1, 1932

By Robert Anderson

DURING the past 5 years no subject has aroused more interest or received more attention among mill operators than flotation. One reason for this is, undoubtedly, the remarkable success of the process in Australia where that country has risen to the position of furnishing one-fifth of the world's Supply of zinc. The plant of the Butte & Superior Copper Co., designed by James M. Hyde in 1912, was the first important large flotation plant in this country; other installations have been made since then with considerable frequency, particularly so in the last 2 years. Without going into complete detail, it may be safely said that although flotation is a highly successful commercial process, it is more or less on an empirical basis. Upon scanning the literature, it is found that the flotation investigations have, in the main, dealt with a solution of the problems which accrue to practise; until recently no attempt was made to remove the difficulties in the way of the formulation of a consistent and harmonious theory. Of late this phase of the work has been receiving considerable attention, particularly by the United States Bureau of Mines at its Salt Lake City station, by the Mellon Institute at Pittsburgh, by the General Engineering Co. at Salt Lake City, by many of the mining schools, and private individuals almost ad infinitum. There is, at present, an enormous amount of laboratory work being carried on in flotation research, and probably the time is not far away when a generally acceptable explanation of flotation phenomena can be Set forth. However, at this time, it seems as though the current technology is befogged with a super-abundance of contradictory evidence; this confusion can only be dispelled as time proceeds and the knowledge of the subject becomes more complete.

Jan 7, 1916

By Edmund Kirby

THE results to come from the application of cheap oxygen to industry in general will be so great that it is not possible to enumerate them beforehand and still less to estimate them. We naturally think first of the fuel to be saved; yet this is only a minor item. The main results will be changes in methods of manufacture or of operation. The speed of operation will be greatly increased, with consequent savings in labor and fixed charges, and also, in most cases, in the cost of fuel. High temperature will be brought within the reach of every manufacturer, whereas it is now available only to those operating expensive electric furnaces located within reach of large water power. New speeds and new temperatures mean improvements and processes not thought of at present. Incidentally the changes in methods will probably change the location of important world industries, the tendency being to concentrate at the fuel centers. The whole subject is so new that most of the data which an engineer requires for definite estimates do not exist. All that is possible now is to obtain a general view of the subject with rough and fragmentary estimates for some of the industries with which we are specially concerned. Most of the figures presented deal with fuel saving merely because there are available no data from which to estimate the effect on speed of operation. When working out the practical problems involved in substituting oxygen for air, in most cases the change will be made step by step; by trying out air enriched with increasing percentages of oxygen. Such partial applications of oxygen will be temporary expedients during the transition and there will be no stopping place short of the complete substitution of air by oxygen. This final stage is therefore the one discussed in this paper.1

Jan 11, 1924

By D. S. Eppelsheimer, D. N. Williams

The compression texture of iodide titanium is determined and found to consist of a [0001] texture rotated 15° to 30° from the axis of compression. As the amount of reduction increases, the angle of rotation decreases. The 0001 rotation showed a slight preference for a <1010> rotation axis. RECENT investigation of the cold rolled texture of titanium&apos; has shown this metal to exhibit a new type of rolling texture. This texture can best be described as a (0001) [10i0] with the 0001 planes rotated approximately 30" to the transverse direction around a <10i0> rotation axis. Rather good results in explaining the cold rolled texture have been obtained by other workers&apos; by examination of the tension and compression textures. No information was found giving the tension texture of titanium. Generally the tension texture of a hexagonal close-packed metal is identical with its wire texture. The drawn texture of titanium has been investigatedh nd has been found to be predominately [10?0]. Since this is the common tension texture of hexagonal metals of low c/a ratio, the explanation of the difference between the rolling texture of titanium and the rolling texture of other hexagonal metals is not indicated by examination of the tension texture. Therefore, the compression texture of titanium should be particularly important in the explanation of the unusual transverse rotation of the 0001 planes found in the cold rolled texture. The compression texture of titanium was examined by Yen.",&apos; His results showed titanium to exhibit the usual [0001] texture up to 85 pct reduction. At higher reduction a double texture appeared in which the 0001 planes were rotated from 10" to 30" from the plane of compression. This change in the compression texture seemed unusual since the tendency for hexagonal close-packed metals is to approach the [0001] texture as the idea compression texture. Mechanical twinning generally occurs over a considerable range of reductions beginning at a rather low reduction. The samples used by Yen in his investigations were prepared by two methods. Compression in a testing machine was used up to a reduction of 85 pct. Compression by compression rolling was used at higher reductions. Since the change in texture occurred at the same reduction as the change in the method of compression, a connection between the two seemed likely. To check this possibility and to locate the position of the change in texture definitely, if it was found to exist, the compression texture of titanium was re-examined. An iodide titanium crystal bar (99.9 pct Ti) produced by the New Jersey Zinc Co. and donated by the Titanium Alloy Manufacturing Div. of the National Lead Co. was used in this investigation. Procedure The investigation of the compression texture was carried out in three steps; compression, specimen

Jan 1, 1953

By C. E. Stafford

and tougher, and will carry double the tonnage of any of Dr. Dud ley&apos;s soft mils. C. E. Stafford, Steelton, Pa.: I must confess my high ap preciation of Dr. Dadlq&apos;s conscientious and painstaking work, and of his scientific methds in obtaining the data; but with his method of handling these results and with his conclusions drawn therefrom 1 canuot agree. The reasons for this difference of opinion I will endeavor to explain. It is apparent on inspecting his Plates 6 and 7 that the majority of the slower-wearing rails are from the north track, and generally have a longer time of service, a greater average tonnage per rail, and a smaller avernge tonnage per year per rail than the faster wearing, the majority of which are from the south track, and gener ally have a shorter time of service, a smaller average tonnage per rail, and a greater average tonnage per year per rail. Have these facts any significance Have these different of conditions to which they are subjected any baring on the relative wearing capacity of these rails I venture to say they have. I think, after a study of Table I (page 676), (an arrangement of linee 17 and 18 of Plate a), in connection with Plates 6 and 7, we will find that the slower wear of the 32 best rails is only partly due to qualities inherent in the rails themselves, but is principally due to external conditions favorable to slower wear. In regard to the north and south track, we know that over the rsoiith track come the loaded cam from the West, and that over the north track these cars return, most of them, empty. It is evident that this means for the north track a less average tonirage per rail per year; or, in other words, a lower wheel tonnage. When the load per wheel is less, the resistance and consequently the wear must, necessarily, be less, other things being equal. Time of service, alee, has an important bearing on the question in hand. It has been only within the last five or six years, as Dr. Dudley has pointed out, that the roadbed of the Pennsylvania Rail road has reached its present admirable condition. Before this time the njadbrd was more elastic, more yielding (and probably not uni tbrmly so) than at present. These circumstalices might cause a sofier rail to be more durable than a harder one, owing to the fact that it ulonId yield rnore or less to the bending force of the passing load and would thus get a bearing on each cross-tie. The harder rail, on the other hatid, being stiffer and more. unyielding, would not

Jan 1, 1881