Search Documents

By J. B. Wagstaff, R. A. Buchanan, J. F. Elliott

High speed photography through blast-furnace tuyeres showed coke particles moving rapidly. Model studies showed a raceway was formed and gave quantitative results which were correlated with actual blast furnaces. Another study showed the similarity between hanging and the flooding of a packed column. This was explored by models. THE combustion zone before the tuyere in an iron blast furnace is a vital region because here are generated: 1—most of the gases on which the furnace depends to carry out its basic operation of reducing iron ore to the metallic state, and 2—the major fraction of the heat required in the nearby regions of the furnace for the various reduction reactions, the fusion of the slag, and the melting of the iron. Since the greater part of the coke is consumed in this region, the descent of the burden must be greatly affected by the characteristics of the tuyere zone. This region then would seem to be a profitable field for study. Fortunately, a view into this important zone is available to the operator through the tuyere peep sight. Here he sees relatively dark pieces of coke "dancing" in the blast. What he sees is of considerable help in interpreting the behavior of the furnace at a given time but the very rapidly moving particles and the intense radiation obscures what is happening very deep in the zone. This investigation was initiated in the hope that a better understanding of the combustion region could be obtained by using a high speed camera with a maximum speed of 3000 frames per sec. It seemed the best practical method of "slowing down" this characteristically violent action within the highly luminous field. Model studies and tuyere probing also have been used to aid in explaining the observed phenomena. Above the combustion zone, but below the fusion zone, there is probably a region in which the coke is comparatively stationary. Here are zones in which the gases must flow up through the granular bed counter to descending liquid slag and metal. There is no easy way to observe this zone in a blast furnace, but model studies have been of some help in explaining the nature of the zone and the laws governing the flow of the fluids involved. The whole problem is difficult and involved and any approach to a complete solution may require long investigation. This preliminary report has been written, therefore, because it is believed that appreciable progress has already been made that would be of interest to others. Tuyere Studies, Chemistry and Kinetics It is well known from the early work of Kinney and coworkers1,2 that combustion of carbon before the tuyeres appears to occur in two zones: Zone A: C + O, = CO2; AH77°F. = — 14,108 Btu per lb of carbon [I] Zone B: CO2 + C = 2CO; H77°F = + 6,183 Btu per lb of carbon [2] Zone A (Fig. 1) is close to the tip of the tuyere and zone B is somewhat farther back; there being a transition region in which both reactions occur. It is interesting to estimate the rate at which coke is burned before a tuyere with a wind rate of 90,000 cfm in a modern furnace having 18 tuyeres. Approximately 0.55 lb of carbon is consumed by eq 1 per tuyere per sec. A like amount disappears by eq 2 for a total consumption of 1.11 Ib per sec per tuyere. Assuming the coke is 85 pct C and has a bulk density of 30 lb per cu ft, this figure can be converted to a total of 1.30 lb of coke with a bulk volume of 0.043 cu ft disappearing per sec per tuyere. At the temperatures prevailing in the combustion zone (according to Kozlovich,³ he maximum is about 3400°F), the rate at which carbon is con-

Jan 1, 1953

By J. A. Stachura

Continuous mining machinery provides the coal industry with one way to compete for a larger share of the total energy market. Various types of machines are discussed and some of the problems with continuous miners, encountered by operators, are reviewed. Equipment manufacturers are working with mine personnel to provide solutions for problems that arise. While coal production over the past 25 or 30 years has been on a horizontal plane, coal's share of the total energy market has declined. To participate more effectively in this total energy market, it is necessary to produce coal more efficiently. It is the obligation of all management, employes, and mining departments to gear the deep mining industry to the rapid progress and changing of today's modern industry. This can be accomplished in the near future with the selection of the proper type of continuous miner best suited to each operator's individual situation. In most mining operations there is tremendous incentive to undertake the continuous mining program. It can reduce the size of the mine greatly by permitting a minimum of working places; it makes pillar recovery work more efficient from the standpoint of overall cost, amount of coal recovered, and safety. The work force can be reduced materially permitting closer and more efficient supervision. It simplifies maintenance because equipment can be more readily standardized. The trend of the coal market favors the use of continuous mining machines. Although there appears to be a general feeling that continuous mining is still a relatively new program and will be slow in replacing conventional mechanical equipment, the fact is that tremendous strides have been made since the first machines were installed in 1948. This program is advancing at approximately the same rate that mobile loading machines replaced hand loading. From 1948 to 1955 there were approximately 450 continuous mining machines in service. In October 1959, a survey revealed that there were more than 700 continuous mining machines in service. Many operators have expressed a desire to undertake this program, but they feel that they could not do so at this time because of one or more of the following reasons: 1) the thickness of their coal seams, 2) seam characteristics, 3) soft bottoms, 4) bad roof conditions, 5) size consist, 6) insufficient flexibility in machines, 7) difficult ventilation problems, and 8) high maintenance costs. With the realization on coal about the same today as it was in 1948, or slightly less and since coal is still failing to participate to a greater degree in the total energy market, it is not surprising that the coal industry is desperately exploring more economical methods for deep mining. The manufacturers are aware that the coal industry is willing to invest in continuous miners if the equipment is built for maximum flexibility, will produce higher tons per man, and assure long life between overhaul programs. CONTINUOUS MINING MACHINES Before discussing details regarding the selection of a continuous miner, let us have a preview of some of the continuous mining machines which are available to the coal industry today. Jeffrey Manufacturing Co.: The machine shown is the Jeffrey 76 A.M. Colmol. This is their most widely used miner, and has been particularly successful in central Pennsylvania and in high-wall mining in western Kentucky. One of the outstanding features of this auger-type miner is its portability. The entire mining range can be changed from its lowest point to the maximum height without stopping the mining operation. Jeffrey 76 B.M. Colmol: This machine is similar to the 76 A.M. model; however, it is built bigger and stronger for a mining range of 50 1/2 to 72 in. This is the model that is now available (Fig. 2). Jeffrey has added two arms to the top row, omitted the odd arm in the bottom row, thus permitting a 50 pct larger throat opening. This eliminates one

Jan 1, 1961

By K. D. Jacob, W. L. Hill

Fluorine recovery in the United States has been restricted chiefly to manufacture of ordinary superphosphate and wet-process phosphoric acid. However, there is an expanding use of fluorine by industry in the form of hydrofluoric acid. Improved methods for recovering fluorine from phosphate rock would yield an adequate supply of fluosilicates and a substantial contribution to the hydrofluoric acid requirement. THE bulk of natural phosphates is comprised of calcium phosphates, which are usually apatites;' calcium aluminum phosphates such as pseudowavel-1ite; and aluminum phosphates, which occur in extensive deposits, notably on Grand Connetable Island." Nearly all deposits of current commercial value are apatite, often with admixed material of other classes. In the trade coarsely crystalline material, mainly fluorapatite of igneous origin, moves as apatite, whereas the fine-grained material of sedimentary origin is marketed as phosphate rock. The latter classification includes the phosphate shales in western North America. Although several genetic varieties of phosphate rock are recognized, most known reserves are of marine origin. Calcium phosphate is concentrated from Florida land pebble and Florida hard rock deposits and from Tennessee brown rock deposits. Phosphate Rock as a Fluorine Carrier: More than two decades ago Reynolds and Jacob surveyed the fluorine content of commercial phosphate rock from various parts of the world. Later these samples were re-analyzed by a new and more reliable method of determining flourine. The revised results with interim additions of new samples, published a few years ago in a brief summary," are shown in Figs. 1-3. Through the points representing the respective varieties of rock medial straight lines are drawn. In some instances the lines are well defined by the points; in others, where scattering renders the position of the best line uncertain, the greater weight is given points near the end of the covered range. Wherever distinct varieties are not recognized among regional deposits the custom is to identify the sample with the geographical location of the deposit. Although all rock varieties cannot be classified with certainty, the plotted results exhibit three distinct types of rock in which the F to P2O5 ratio diminishes, remains sensibly constant, and increases, respectively, as the grade of rock increases. Existence of two types of Florida land pebble, Fig. 1, is supported by additional results recently supplied by a producer." Generally speaking, phosphate rock from continental deposits carries considerably more fluorine, and apatite and insular phosphates less, in proportion to the phosphorus content than is required by the formula for fluorapatite. Exceptions to this are apatite from Canada and certain samples of Florida waste-pond phosphate. The manner in which excess fluorine is held and the nature of the carbonate in carbonate apatite are discussed in recent articles. High-grade calcium phosphates with F to P2O5 ratios less than 0.05 have been found in Curacao, Christmas Island," Mexic,13 and elsewhere. The calcium aluminum phosphates and aluminum phosphates aften carry notable amounts of fluorine. The F to P2O, ratio for one sample of pseudowavel-lite concentrate was 0.05." Aluminum phosphate from Grand Connetable Island is very low in fluorine, whereas some aluminum phosphate minerals" carry as much fluorine as highly fluorinated phosphate rock. Fluorine in Domestic Phosphate: The curves shown in the figures permit interpolation of the F to P2O5 ratio corresponding to the midpoint of selected ranges in grade of any one of the several varieties of phosphate. Multiplication of the interpolated ratio by the mid-range grade (P2O5) yields a figure for the percentage of fluorine in this grade. Then, with the use of the mid-range grade, the amount of fluorine held in phosphate reserves can be estimated, see Table I. Accordingly, on Jan. 1, 1950, the fluorine complement of known domestic reserves exceeded 420,000,000 long tons of the element. A previous figure," deduced in 1940 by a simpler procedure

Jan 1, 1955

By J. W. Marx

A method is given for predicting the complete gravity drainage characteristics of arbitrarily long columns from centrifuge drainage measurements on reconstituted core samples. Oil residuals corresponding to hundreds of years of normal gravity depletion can be obtained in a few hours on the centrifuge. The gravity flow rate at any stage of the depletion process may be determined from the time correlation derived, and experimentally checked, in this study. INTRODUCTION Apart from the original observations of Muskat et al1, research publications2,3,4 on the subject of gravity drainage have been largely concerned with establishing in detail the saturation, S as a function of the height, z, in a draining column at any given time, t. Some form of numerical integration must be employed to obtain production rates and cumulative production even when S(z, t) is known. Furthermore, the relevant experimental work has been concentrated on drainage of a single wetting liquid from unconsolidated media. Since oil production usually concerns the drainage of a partially wetting liquid from consolidated media, in the presence of connate water, and since it is unlikely that sufficient information exists to establish S(z, t) in detail for any natural reservoir, the published research work appears to be, at best, only qualitatively applicable to production problems. With this in mind, the present study was undertaken by the writer. Experiments were planned whose results would have two advantages over existing measurements: 1. Observations were to be made on specific reservoir rock, reconstituted with formation water and formation oil. This would reduce their generality, from the research viewpoint, but increase their utility for production purposes. 2. The measurements were to be self-integrating, i.e., the phenomena were to be described and interpreted in terms of cumulative results. THEORETICAL DEVELOPMENT It was commonly known that centrifuging a liquid bearing porous medium increases the drainage rates and minimizes capillary end effects. The specific problem lay in selecting an acceleration, a, such that the mean residual saturation of a model cylinder was equal to the residual saturation of an arbitrarily long prototype column when the latter was drained by earth gravity alone. The physical conditions required to permit a valid scaling of model drainage time, tm with prototype drainage time, t, may be stated as follows: (a) At t = tm = O, So = Smo; (b) At t = tm? 8 Sr. = Smr.; (c) For all intermediate values of t and dS/dt=dsm/dtm whenever S = Sm; (d) S(z) = Sm(z) = a constant when t = tm = 0. 1 Here S = T I S(z)dz, where h is the length of the « Jo cylindrical column being drained and the subscripts S,Sm, and refer to model, initial, and residual systems, respectively. The first three conditions mean, simply, that an 3 vs t plot will be numerically identical with an S, vs t, plot,

Jan 1, 1957

By H. E. Criner, M. G. Driessen

THE cyclone thickener has two important applications in wet washing plants: (1) water clarification, and (2) fine coal recovery. The thickener consists of a conical chamber into which the fluid is injected through a tangential nozzle at the periphery of the large end. The solids of the slurry are concentrated and removed from the apex of the cone while the "thinner" portion is discharged from a central tube in a flat head at the large end, fig. 1. The advantages of the cyclone thickener are that large volumes of slurry may be treated with small space requirements and that the underflow concentration may be controlled easily and readily to meet varying feed conditions. Control of Washery Water Solids Concentration: The first requirement, in the process of controlling solids concentration, is that the solids be removed from the body of circulating water at the rate at which they are introduced. If this condition is satisfied the concentration will remain at a fixed value and will not increase to uncontrollable levels. The second requirement is that the solids concentration

Jan 1, 1951

By M. G. Driessen, H. E. Criner

THE cyclone thickener has two important applications in wet washing plants: (1) water clarification, and (2) fine coal recovery. The thickener consists of a conical chamber into which the fluid is injected through a tangential nozzle at the periphery of the large end. The solids of the slurry are concentrated and removed from the apex of the cone while the "thinner" portion is discharged from a central tube in a flat head at the large end, fig. 1. The advantages of the cyclone thickener are that large volumes of slurry may be treated with small space requirements and that the underflow concentration may be controlled easily and readily to meet varying feed conditions. Control of Washery Water Solids Concentration: The first requirement, in the process of controlling solids concentration, is that the solids be removed from the body of circulating water at the rate at which they are introduced. If this condition is satisfied the concentration will remain at a fixed value and will not increase to uncontrollable levels. The second requirement is that the solids concentration

Jan 1, 1951

By Ronald W. Klusman, Erik B. Nelson

The Front Range portion of the Colorado Mineral Belt is an extensive area of mineralization with mining activity dating from 1859 with the discovery of large gold deposits. After an initial boom period and gradual diminishing production, present activity is restricted to molybdenum in Clear Creek County, uranium in Jefferson County, and several small operations extracting gold and silver in Clear Creek and Gilpin Counties. Gold and silver have dominated the production in the Front Range, though the complex mineralization created milling and smelting problems and it is postulated that considerable amounts of precious metals remain in the mine dumps. This area is plagued by a severe mine drainage problem, with Clear Creek most impacted by many draining mines and tailings in the basin. Boyles et al. Moran and Wentz, Wentz, Wildeman et al., have examined various aspects of the impact of mine drain¬age in the Clear Creek basin. The primary objective of this study was to collect data on the tailings, drainages, and leaching experiments in order to make preliminary suggestions for reducing the impact while recovering metal values to offset treatment costs. A variety of leaching experiments were performed on tailings from the Nevada Gulch area in the Central City mining district. Leachings were performed in vertical tubes indoors and wooden boxes exposed to the outside environment. In the leaching experiments, the leaching solution, grain size, and residence times were varied, while forced aeration was used in some experiments. Bacterial nutrient 9K° and mine drainage were used in some of the experiments. A total of 14 additional tailings samples were analyzed for base and precious metals. The composition of the mine drainage and tailings used in the leaching experiments, as well as data on the additional samples are shown in [Table 1]. Leachate samples were taken periodically for analysis until compositions leveled off. Results and Discussion Leaching with distilled water was used as a control and best illustrates the basic behavior of the leaching process for zinc in a vertical tube [(Fig. 1)]. More acidic leachings increased concentrations of metals as did smaller grain sizes, though the time required increased significantly. Mine drainage with its high concentration of dissolved iron sometimes decreased the heavy-metal concentration in the leachate due to oxidation of Fe 2 and precipitation of Fe(OH)9 which absorbs some of the dissolved heavy metals. In the larger scale experiment carried out in the simulated leaching pad, substantial concentrations of metals were attained in the final leachate after one month. In this experiment the leachate was not recycled, but allowed to saturate the tailings continually with evaporation loss made up by additions of Quartz Hill drainage and nutrient 9K. The concentration of the metals in the leachate and the increase over the input solution are given in [Table 2]. Heap leaching of low-grade copper and uranium ores is successfully carried out in many districts, enhanced by the metabolism of autotrophic bacteria of the Thiobacillus-Ferrobacillus group. These ubiquitous organisms enhance metal leaching, and general aspects of heap leaching are discussed by Malouf, Trudinger, Pings, and Duncan et al. Conclusions and Recommendations Returning to the primary objective, how to reduce the mine drainage impact and recover metal values, we need to consider how the data may suggest avenues toward this objective. Boyles, et al., considered various

Jan 1, 1977

By Frank C. Greene

Drilling in Missouri in 1945 dropped slightly from the preceding year. The only notable development was that in the Ballard area in Bates County, where a number of farmers drilled private gas wells with an average depth of a little more than 30o feet. Table 1 gives a summary of activities by counties. The total footage drilled was 36,186 ft. of which 20,489 ft. was by cable tools and 15,697 ft. by rotary tools.

Jan 1, 1946

By J. C. Fisher

Martensite transformations in steels and other alloys are characterized in part by the absence of composition changes during the growth of a new phase. Transformation occurs rapidly, and there is insufficient time for long range diffusion or partition of alloying elements to take place; martensite reactions in alloys thus are similar to phase transformations in single component systems. A fundamental understanding of martensite transformations in steels is impossible without knowledge of the free energy change upon transforming austenite (face centered cubic iron containing alloying elements) to ferrite (body centered cubic iron containing alloying elements) of the same chemical composition. The present paper assembles the best information available concerning the influence of temperature and composition on this free energy change. Most of the material has been taken from the work of Johansson,' Mehl and Wells,2 Zener3,4 and Smith;5 and indirectly, through these authors, from the work of Austin.6 In agreement with the generally accepted viewpoint, martensite is assumed to be an ordered solution of carbon in ferrite of the same composition as the parent austenite; only at high temperatures and low carbon concentrations is the carbon in ferrite distributed at random. The properties of the disordered solution are estimated by extrapolating the known properties of iron-carbon solid solutions into the range of supersaturation, and the free energy change associated with ordering is estimated from the theory developed by Zener. By incorporating Smith's recent thermodynamic measurements and Zener's theory of ordering, the present analysis modifies previous estimates of the free energy change associ- ated with martensite transformations. Consider a two component system consisting of a solvent A and a solute B. Let Na and Nb represent mol fractions of A and B respectively, let aa = raNa and ab = YbNb represent activities, and let superscripts 1 and 2 refer to phases 1 and 2. The partial molal free energies of A and B in phases 1 and 2 can be summarized as follows: free energy standard state Fa' - Fao1 = RT In an1 pure A' Fa2 - Fa2 = RT In aa2 pure A2 Fb1 - Fbo = RT In ab1 pure B Fs2 - FB2 = RT In aB2 pure B. The free energy of a gram atom of phase 1 is* AF1 = Na'Fa1 + Nb'Fb1 and that of phase 2 is AF2 = NA2FA2 + NB2Fb2. A martensite transformation from phase 1 to phase 2 requires Na1 = Na2 = Na and NB1 = NB2 = Nb, and the free energy change per gram atom accompanying transformation is AFi-2 = NA(Fa2 - Fa1) + Nb(Fb2 - Fb1) = NA[RT In (aA2/aA1) + AFa1?2] + Nb RT In (aB2/aB1) = Na[RT In (ra2/ra1) + AFa1?2] + Nb RT In (TaVTB1). [1] where yn2, yn1, yB2, yB1 are activity coefficients, and where Ma'+* is the free energy change upon transforming a gram atom of pure A from phase 1 to phase 2 at the temperature in question. For martensite transformations in plain carbon steels, A = iron (Fe), B = carbon (C), 1 = austenite (7). 2 = ferrite (a), and Eq 1 is AFr ?a= NFe[RT In (rf.a/rfer) + AFF.r?a] + TVc RT In (eca/rc1)- L2] Nothing is known concerning the values of yFea and yca for carbon concen- , trations in excess of 0.025 pct. However, the approximation rf.7 = 7f." = 1 cannot be appreciably in error for small carbon concentrations, and Eq 2 reduces to Afr-a = NfeFfer?a1 + NC RT In (rca/rcr)- [3] Johanssonl and Zenera have calculated MFfr?a from the specific heat measurements compiled by Austin.6* Their calculated values agree closely, and are summarized in Table 1. The activity coefficients relative to graphite for carbon dissolved in iron vary with temperature according to the relationships d In rcr/d(1/T) = AHcr-R dlnyca/d(l/T) = AHCa/R where AHc? and AHca are the heats of solution of graphite in y and a iron. Assuming the values of AH to be independent of carbon concentration and temperature, In rCr = AHcr/RT + I1 In rca = AHCa/RT + 12

Jan 1, 1950

By H. E. Stauss, J. Hino

INTEREST in silicon has arisen again in the past decade as a result of improvements in crystal rectifiers.' Although the preparation of silicon was first reported by Berzelius in 1880, the early product was of relatively low purity, and only the need for rectifiers in World War II led to the production of a 99.9+ pct pure powder. This material in crystalline form was consolidated into massive silicon for use, and the method developed was to melt it with selected added constituents as "doping" agents. Melting techniques, therefore, are of great importance. There are two basic problems in producing silicon ingots free of doping additions; one is the prevention of spitting and the other is prevention of cracking of the ingot during freezing. The most satisfactory arrangement yet developed for producing massive silicon is to melt and freeze in a cylindrical quartz crucible surrounded by a concentric heating element and concentric radiation shields or insulation. For example, use can be made of a tubular heater with a high frequency generator as the source of power and reflecting shields of alundum cylinders. The spitting of silicon is related to gas evolution, and the gas comes from two primary causes—adsorbed gas and the reaction products of silicon and the crucible. Gas is also released from bubbles contained in the quartz crucible walls. Improved removal of adsorbed gas can be achieved by means of controlled melting and freezing. The seriousness of the problem in vacuo is reduced with an electrically operated mechanical movement of the high frequency power coil. The upper portion of the powder charge is melted first and the high frequency coil lowered until the powder is completely molten. During cooling the high frequency coil is raised slowly. These means also reduce the final nonviolent extrusion of large beads of metal through the ingot top during freezing. Better control of spitting and bead extrusion is obtained when melting is done under helium at. atmospheric pressure instead of in vacuo. The problem of reaction between silicon charge and crucible in practice is confined to the reaction between silicon and quartz. This2 apparently is: Si + SiO2 + 2SiO The part that this reaction plays in spitting has not been isolated for separate study. SiO is a volatile vapor at the melting point; of silicon and is released freely during melting in vacuo, but hardly at all in helium at atmospheric pressure. The cracking of ingots is a major difficulty in melting silicon, and its prevention requires special melting techniques or the addition of "toughening" agents such as aluminum or beryllium.' The cracking of the ingots has been explained as being the result of the expansion that occurs upon freezing; although direct observation of freezing ingots reveals visible cracks on the surface only after a red heat has been reached, suggesting that cracking is the result of differential contraction of silicon and quartz. Silicon wets quartz, and the ingot adheres tightly to the crucible. Therefore as ingot and crucible cool, the two either have to pull apart, or at least one must crack. Surprisingly, in spite of the relative thinness of the quartz and the thickness of the ingot, the ingot and the crucible both crack. Microscopic and X-ray4 studies fail to show any plastic flow other than twinning in the ingots. Slow cooling fails to prevent cracking. Another possible solution to cracking is to weaken the crucible. Use of thin-walled crucibles finally led to success with fused quartz crucibles with a wall thickness of 0.25 to 0.50 mm. With such thin-walled fused quartz crucibles consistently uniform success is secured in producing sound ingots 30 mm in diam from the purest available grade of silicon (99.9+) without the use of any type of addition. Melts are made in the size range of 50 to 100 g. Omission of a deliberately added doping agent is not sufficient to insure pure ingots. The reaction of silicon with crucibles and the resultant solution of impurities in the silicon is well-established." In this laboratory, the presence of Al, Be, and Zr has been found spectroscopically in ingots melted in contact with alumina, beryllia, and zircon. The best crucible materials reported in the literature are MgO and SiO2. Use of MgO in this laboratory has resulted in a heavy deposit of magnesium on the furnace walls, showing that a reduction of the magnesia occurred and the resulting magnesium removed from the melt by volatilization. In the case of quartz, the silica is reduced and SiO liberated to deposit on the equipment walls. There probably is real danger that oxygen is dissolved in the ingot when either magnesia or silica is used as the crucible material. Preliminary analyses by Dean Walter in his vacuum unit in this laboratory6 indicate the presence of oxygen in undoped silicon melted in quartz.

Jan 1, 1953

By Hjalmar W. Johnson

IT has long been accepted that blast-furnace practice varies to some degree with the coke used. While the qualities desirable in iron have been known for some time, the qualities in coke that produce such iron have not been established. There are no objective standards for blast-furnace coke, which is usually described in general terms, as good or bad. Many experienced operators believe that coke cannot be measured objectively except by using it in the furnace, noting the result, and labeling the coke according to furnace operations. This is admittedly unscientific, and besides is useless for the two main purposes for which a measure of coke quality is needed: (I) to produce the best possible coke from the coals and equipment on hand; (2) to test new coals and determine their value for blast-furnace coke. In seeking such an objective measure, much work has been done on tumbler tests, shatter tests, sizes of coke, porosity, specific gravity, reactivity or combustibility and other tests, but as yet very little has been published in which conclusive correlations have been established between such objective measures and furnace operation. In our study of the problem during the past 8 years we have developed no new measures of coke quality, but we have collected data that are presented here in the hope that they may assist in further work, so that at some future time there may be developed such positive measures. The purpose of this paper is to show that there are variations in coke and that such variations do influence the operation of blast furnaces. At the same time we must remember that there are variations in blast-furnace operation and it may be the blast furnace that is at fault. This correlation of coke properties with blast-furnace operation will be worked out in the following steps: I. Discussion of a period when a change in the coke resulted in an increase in efficiency on one furnace and a decrease in efficiency on another. 2. Adaptation of the inefficient furnace to the available coke so that normal efficiency was restored. 3. The use of radial distribution: a discussion of the effect of size of ore layer in adapting blast-furnace operation to the coke. 4. An example of a change in size of coke and the detrimental influence on the production of one furnace. 5. An example of a change in size of coke, together with manufacturing data, to show why it changed, the conclusion being that coke is a product with an optimum value. 6. Illustration of the fact that coke has different optimum values on two furnaces, with discussion on adaptation of operation so the optimum values will be the same. 7. Limitations of the use of screen tests as an objective measure of coke quality. 8. Importance of uniformity in coke. FUNCTIONS OF COKE AND QUALITIES REQUIRED TO PERFORM THESE FUNCTIONS Coke has three important functions in a blast furnace: (I) to furnish most of the

Jan 1, 1941

By P. Pollard

A method has been developed for evaluating acid treatments in fractured limestone fields by breaking down pressure drawdown into three component parts: (I) pressure differcntial across "skin" near the borehole face, (2) pressure differential due to flow resistance in the coarse communicating fissures and (3) pressure differential between the fine voids and the coarse fissures. It is apparent that in most successful acid treatments the first term, skin resistance, has been reduced or eliminated. Further, it is often possible to estimate the volume of coarse fissures associated with the second term, coarse fissure flow resistance. In cases where this volume is comparable with practical acid volumes it seems likely that this resistance also may be attacked with a suitably retarded acid. INTROD UCTION Acid treatment has been successfully applied as a general practice in the limestone wells in the Mara/ Maracaibo districts of Venezuela for some 10 years. At the same time the need has been felt for a more precise method of: (1) evaluating the effect of an acid job and (2) selecting wells which should benefit from an acid treatment. The following method, based on an analysis of build-up curves for wells producing from fractured limestone, provides a means of forecasting the effect acid will have on a well and in many cases the probable order of production rate increase which may be expected. In certain cases it is also possible to calculate the fissure volume through which the acid has to be displaced for best results. Various approximations are introduced in the method, but within the limitations of these the analysis gives an indication of how a well, whether previously acidized or not, may be expected to respond to acid treatment. Suitable build-up curves cannot be obtained on "tight" wells which do not give sustained production and the method is not applicable to such wells. Figs. 1 through 7 illustrate various types of build-up curves obtained from limestone wells in Western Venezuela. Curves are included showing (1) both skin and coarse fissure resistance, (2) skin resistance only, (3 and 4) reduction of skin resistance by acidization, (5) fissure resistance only, (6) reduction of coarse fissure resistance by acidization, and (7) acidization failure. This theory has been successfully applied for over three years during which 22 acid treatments have been carried out specifically to reduce skin resistance and three treatments to reduce coarse fissure resistance. The method has been found to be a useful aid in the selection of wells for acidization.

By J. C. Holm

ALTHOUGH the main constituents of Portland cement are the oxides of calcium, silicon, aluminum, and iron, characteristics of the cement are seriously affected by such contaminants in the raw materials as magnesium, phosphorus, sodium, potassium, sulfur, and others of lesser importance. Sources of cement raw materials comprise a long list of minerals occurring in nature in various degrees of purity. The calcareous raw materials are generally limestone of purity varying from calcite to cement rock (a low-grade limestone of natural, almost correct chemical composition), chalk, marl, seashells, coral, and coral sand. The argillaceous raw materials supplying silicon, aluminum, and iron are mainly various forms of clay and shale, to which may be added silicious sand, iron ore, bauxite, or kaolin for minor adjustment of the chemical composition. The quality of Portland cement in this country, as in most parts of the world, is controlled by rigid specifications limiting both its chemical and physical characteristics, and cement manufacturers must comply with these specifications to market their products. Brandon Raw Materials: An unusual deposit of marl, limestone, and clay occurs 12 miles east of Jackson, Miss., near the village of Brandon. The deposit is of sedimentary origin and of relatively young geological age. Layers of marl vary from putty-like consistency to such hardness that it can be cut with a knife. Interspersed between the layers of marl are bands of limestone varying from very soft to hard. the compressive strength of the hardest layers exceeding 15,000 lb per sq in. The layers of marl range in thickness from a few inches to about 25 ft. The limestone bands seldom exceed 2 to 3 ft but often occur in thinner veins in the quarry face. Above the top layer of the deposit, which may be marl or limestone, a layer of clay ranges in thickness from a few inches to more than 20 ft. Part of this clay is harvested with the raw material to supply part of the argillaceous components, but most of it is stripped as overburden and wasted. A highly silicious clay of extreme fineness, harvested from the bottom of the quarry below the marl and limestone bands, is to correct the silica content. Fig. 1 shows typical examples of the interrelation of the various materials, based on drill logs obtained during exploration of the deposit. The marls vary in moisture content in the bank from 15 to 30 pct and contain up to 70 pct -200 mesh particles and up to 40 pct —10 p particles. A large percentage of the fine fraction is within the colloidal range, making the marl extremely sticky. The limestone beds range in hardness from that of the hardest marl to a medium hard limestone and in moisture content from 2 pct to approximately 14 pct. The line of demarcation is often difficult to draw and the moisture content is possibly the best means of classification. The ratio of soft to hard material is not constant throughout the deposit, but the average is approximately 70 pct soft to 30 pct hard material. Through the years this deposit had been repeatedly explored by cement companies and rejected as unsuitable for cement manufacture, mainly because of physical characteristics. In 1950, after careful exploration of the deposit and comprehensive laboratory and pilot plant tests of the raw materials, officials of Marquette Cement Mfg. Co. of Chicago were convinced that a practical and economical method of processing the raw materials had been devised and authorized construction of a new plant that began production in December 1951. Marl and limestone, common raw materials for Portland cement, usually occur in such a manner that they can be worked separately. Their harvesting and processing normally have presented no difficult problems, as standard equipment and methods are available for handling either sticky or hard materials. No other cement plant utilizes a deposit of the nature of that at Brandon, however, and for this reason no prior art was available for design. When properly blended, the raw materials produced an excellent cement without additives. Basic problems to be solved in designing the cement plant were:

Jan 1, 1957

GENERAL GEOLOGICAL DESCRIPTION The uranium mineral appraisal herein described was made for an ore deposit in New Mexico. The uranium mineralization occurs as roughly tabular to lens-shaped deposits of varying thickness within the sandstone of the Jackpile formation of Jurassic age. The mineralization occurs at several horizons within the Jackpile formation, but is not always confined to specific beds. It often transgresses across stratigraphic layers, as demonstrated when attempting correlation of uranium gamma anomalies between adjacent drill holes. Preferred mineral trends have been established in some parts of the deposit, but are not always predictable when attempting to extrapolate beyond the zones defined by drill hole sampling. MANAGEMENT OF DRILL HOLE SAMPLE DATA All of the drill hole sample data used in the appraisal were obtained from interpretation of gamma-ray logs. A brief description of gamma-ray log sampling is given in Chapter 2. Two preliminary steps are involved in preparing gamma-ray logs into sample data normally acceptable for computer manipulation. 1) The gamma analog trace produced by the downhole probe must be digitized, i.e., counts-per-second (CPS) are recorded for each 0.15 m (1/2-ft) interval across the gamma-ray anomaly. The work is usually done on a "digitizer" while following the analog trace with an electronic stylus on a special tablet or table. The other alternative is to do the work manually. Some of the newest downhole logging equipment produces a magnetic tape output which can be read by a computer. 2) The gamma-ray CPS values must then be converted to equivalent U308 assay values, taking into consideration all appropriate correction factors. The US Atomic Energy Commission, now part of the Department of Energy, developed the theory and algorithm for this conversion in the 1960's, and though the work can be done manually, it is best done with the GAMRED (gamma-reduction) computer program. Fig. 14-1 illustrates a typical analog trace produced by the probe instrumentation, including gamma-ray trace (left), self-potential electric log (center), and resistivity log (right). Fig. 14-2 shows a form of the computer output after the analog data has been digitized to 0.15-m (1h-ft) intervals and converted to percentage U308 values for the same hole. The U308 grade bar graph on the right permits rapid visual inspection of anomalous values by depth and elevation. The converted U308 sample data were next processed by the SURVEY program that assigned to each assay interval [0. 15-m (1h-ft)] an X Y Z coordinate, taking into account all deviations indicated from downhole survey information. The output file of the SURVEY program was listed on the line printer for examination by project geologists, and also became the main input file for the URAN/ COMP compositing program, which is designed to group individual 0.15-m (/-ft) U308 sample values into larger intervals representing discrete anomalous zones according to a series of specified parameters entered into the program by the user. Composite U308 intervals were computed by the URAN/COMP computer program, the logic of which may be briefly described as follows: Step 1 The program searches for the highest U308 value in the hole and builds a composite by adding the highest grade interval on either side so long as the added value is greater than a minimum acceptable grade, and the total composite, after addition, meets minimum GT (grade times thickness) constraints. Step 2 The program loops back to find the next highest assay value in the hole not already included into a composite, until all anomalies above minimum cutoff grade are composited. Step 3 Individual composites are combined if they are closer than a specified minimum waste thickness, and the resultant composite grade still meets GT minimums.

Jan 1, 1980

By R. G. Knickerbocker, W. E. Brown, G. J. Vahrenkamp, M. M. Fine

THE results of a research and development laboratory and pilot-plant mineral-dressing investigation by the Bureau of Mines of the complex copper-lead-cobalt-nickel ores of southeast Missouri are reported in this paper. This investigation, in cooperation with the National Lead Co., showed that separate concentrates of lead, copper, and cobalt-nickel could be made by fine grinding and flotation. An industrial plant built subsequently by the St. Louis Smelting and Refining Div. near Fredericktown, Madison County, Mo., produced such concentrates during the war years. Present commercial production at the mill is limited to lead and copper concentrates, but research to permit economic utilization of the cobalt and nickel values is continuing. The complex sulphide deposits near Frederick-town in Madison County, Mo., have an operating history that dates back to the years preceding the Civil War. Perhaps these operations can best be summarized in terms of output which are given by Tyler: "Previous to 1900, the Mine la Motte Co. shipped cobalt ore to Swansea and in 1903 produced 120,000 pounds of oxide in a Missouri plant. Another cobalt refinery erected in 1906 by the North America Lead Co. at Fredericktown, Mo., operated intermittently until 1910. In 1909 it produced 83,384 pounds of cobalt oxide, 328,403 pounds of nickel, 8,314 tons of nickel-cobalt concentrates, 600 tons of copper concentrates, and 1,353 tons of lead concentrates. This plant was purchased at a forced sale in 1915 by the Missouri Cobalt Co., which produced a certain amount of oxide in 1918 and in 1920 recovered 102,410 pounds of cobalt oxide and cobalt hydrate, valued at $262,810." According to Buehler,2 "The ore, which consists of a complex mixture of the sulphides of cobalt, nickel, copper, lead, and iron, occurs at the contact of the pre-Cambrian porphyry and the overlying Lamotte sandstone and Bonneterre dolomite." The source of most of the cobalt and nickel is siegenite, a member of the linnaetite series of minerals. Its composition is variable, and although the chemical formula may be given as (CoNi),S,, it usually contains both iron and copper. The siegenite is characterized in this instance by an intimate association with chalcopyrite, and to a lesser extent with iron sulphides. Galena, on the other hand, while dis- seminated throughout the ore, is not closely bound to other constituents. Gangue is composed essentially of dolomite and quartz. Petrographic examination showed that fair liberation of sulphides and gangue could be attained at — 100 mesh. Complete liberation of micronsize inclusions, particularly of sulphides in each other would not have been possible at —400 mesh. Beneficiation Studies Many samples of the southeast Missouri ore were tested, but most of the work was confined to five samples of churn drill cuttings weighing 15 tons. The samples were reportedly representative of five sections of the deposit and were tested individually and as a composite. Only the results of the tests on the composite, which contained 1.28 pct lead, 2.03 pct copper, 1.06 pct nickel, 0.87 pct cobalt, 3.57 pct iron, 15.4 pct lime, and 23.9 pct silica, are presented in this report. In view of the rather complex and intimate association in the mineralogical composition of the ore, flotation was the logical choice in the selection of a beneficiation process. Other mineral dressing unit operations were considered as an adjunct to flotation, but none were beneficial. Many tests were made on these samples to determine the flotation characteristics of the mineral siegenite. As a result of this work, it was noted the siegenite was intermediate in floatability between chalcopyrite and galena on one extreme and iron sulphides on the other. The difference in floatability between siegenite and the iron sulphides was not very great and, in general, the same reagents that depressed pyrite and marcasite would also, in slightly larger quantities, depress siegenite. This tendency for siegenite

Jan 1, 1952

By L. D. Jaffe

From the limited experimental data in the literature, preliminary values were derived for the thermal diffusivity of titanium alloys and for the quenching severity of various mediums used in heat treating them. The thermal diffusivity, under quenching conditions, was found to be approximately 0.006 sq in. per sec. The quenching severity H for brine is approximately 8, for water 4, for oil 0.9, for air 0.08, and for argon 0.02 in. -' The quenching severity of the Jominy-Boegehold end quench water jet against titanium alloys appeared effectively infinite. Using these results, graphs were prepared showing ideal round sizes and Jominy positions having cooled conditions equivalent to those at the center and surface of titanium alloy rounds, plates, and sheets quenched in various media. THE importance of proper quenching of steel parts has long been recognized, and much quantitative work has been done on the subject. Recently, it has become evident that for titanium alloys, too, the rate of cooling from high temperature is important in obtaining high strength and hardness. Maximum hardness and strength may not be attained in the as-quenched condition but rather after a subsequent tempering or aging treatment. Nevertheless, if cooling from temperatures near the ß transus is too slow, for the hardenability of the alloy used, a soft a-ß structure will be produced which will not harden on subsequent aging.'-" The quenching of parts of practical interest can usually be approximated by simple shapes, such as cylinders (rounds) and plates (or sheets) of various thickness and combinations of these. A standard that has been used extensively for comparison purposes is the center of an ideal round: a cylinder quenched in a medium that instantly cools its surface to room temperature." For steel, considerable practical use has been made of the Jominy-Boegehold end quench hardenability specimen,".' and its value for titanium alloys is becoming evident. It therefore appeared worthwhile to attempt comparison of cooling conditions in titanium alloy rounds and plates of various sizes quenched in various media with cooling conditions in ideal round and Jominy quenches. These comparisons are based upon measurements reported in the literature. Quenching Severity of Jominy Water Jet and of Brine As one starting point, there were available the data of Phillips and Tobin8 for positions on a Jominy specimen having the same hardness as the centers of round bars of various size quenched in 5 pct NaOH brine, shown in Table I. The Jominy speci- men is a round bar, normally 1 in. diam and 4 in. long, quenched by a water jet at one end and air cooled on the other surfaces.' After quenching, hardness is measured vs distance from the quenched end on longitudinal flats ground 0.015 to 0.10 in. deep. The data of Table I were based on a subsized specimen of 3/4 in. diam. Since the positions tested are close to the jet quenched end, cooling there may be taken as due solely to the jet, and air cooling can be neglected. These positions are then equivalent to various locations near one surface of an 8 in. plate jet quenched on both sides. Assuming that the thermal diffusivity is constant and that Newton's law of cooling holds, temperature vs time curves at corresponding positions in Jominy specimen and round bar then may be calculated for various assumed quenching severities of the water jet and of the brine. Cooling curves are generally taken to be metallurgically equivalent when they show the same time to reach a temperature halfway between the initial (heat treating) temperature and the final (quenching medium) temperature.5 On this basis, using Russell's tables,9 upplemented by heat flow tables derived in similar fashion by the author for positions near the surface of severely quenched plates, it was found that the experimentally observed equivalence, Table I, was best matched if the quenching severity H of the Jominy water jet was taken as infinite (H = co). This means that the jet quenched surface should be considered as instantly cooled to the temperature of the water

Jan 1, 1956

By G. Britsianes, T. L. Joseph

THE reduction of a lump of iron ore is a complicated sequence of up to three reactions proceeding simultaneously in a gas-solid system. As the ore moves down the blast furnace into zones of higher temperature and higher reducing power, it is successively reduced through the three oxides of iron into metallic iron. The reduction process involves much more than chemical problems. Physical factors add to the complexity of the overall process. Under optimum conditions, reduction of the ore is completed at a level about one-half way down the blast furnace stock column. At this point, the ore undergoing reduction has attained a temperature of about 1000°C and has been in the furnace for about 6 hr. On the practical side, the behavior of the ore during smelting has been of great interest to operators. Unsatisfactory blast furnace operation on burdens containing magnetite ore or badly slagged sinter has often been attributed to poor re-ducibility. The question of reducibility has also been raised in formulating quality standards for agglomerates such as nodules, briquettes, and pellets. In the present investigation, the solid phases formed during reduction were studied as a step toward a better understanding of the overall process. Equilibrium Studies The iron-oxygen equilibrium diagram shown in Fig. 1 reveal; a number of facts pertinent to the gaseous reduction of iron ores. This diagram is from the work of Darken and Gurryl, 2 and represents a correlation of the best available data. Four solid phases may exist during the complete reduction of hematite to metallic iron. These are hematite (Fe2O3), magnetite (Fe3O4), wustite (FeO), and iron (Fe). The wustite phase is a solid solution which is not stable below 570°C. At this temperature the solid solution undergoes a eutectoid-type of decomposition into the phases, magnetite and iron. Thus above 570°C, the diagram dictates that a hematitic ore should pass through a four-phase sequence on reduction to metallic iron. Below 570°C, only hematite, magnetite, and iron should appear. Information on the iron-oxygen system has been derived largely from CO and H2 reduction equilibria. The Fe-C-0 relationships have been studied extensively by R. Schenck and his coworkers and well summarized by H. Schenck.3 More recent studies have been made by Darken and Gurry.1, 2 Data from these sources have been combined and plotted in Fig. 2. With respect to the Fe-H-O system, the works of Emmett and Schultz4 seem the most reliable, and these data have also been included in Fig. 2. Certain physical properties of the solid phases of the iron-oxygen system are summarized in Table I. The crystallographic information is of special interest as much of the present work has been concerned with the X-ray analysis of the products of reduction. Reduction with Hydrogen The reduction of ore with hydrogen is the net result of two or more gas-solid reactions. Above 570°C, the reaction sequence may be represented by stoichiometric stages as follows: 3Fe203+ H2e2Fe,O, + H20 [1] 2Fe3O, + 2H2 6FeOw + 2H2O [2] 6FeOw + 6H3 ^ 6Fe + 6H=O [3] Fe2O3 + 3H2 ^ 2Fe + 3H,O. [4] These reduction reactions follow the general form: A (solid) + B (gas) e C (solid) + D (gas). This type of gas-solid reaction has been investigated by Langmuirl' who has shown that such reactions can occur only at the boundary between the two solid phases. Furthermore, a nucleus of the second phase must initiate the reaction. Once such an interface exists, the reaction proceeds through a layer of the solid reaction product (C). The specific mechanisms involved will depend a great deal on the properties and condition of this particular layer. A number of heterogeneous reactions such as the dehydration of single crystals of copper penta-hydrate and the calcination of limestone follow this type of process. It should be noted that the inter-facial type of reaction also occurs even in dense polycrystalline material which simulates a mono-crystalline behavior.

Jan 1, 1954

By William H. Bassett

RECENTLY it has become the custom of retiring presidents to talk of the relations of the Institute to its membership and its constituency- and it seems a good precedent to follow. Past-president Smith reviewed our relations to materials and to society in general. Mr. Bradley spoke of the value and use of our publications and of our educational duties. My message will be in regard to the coordination of our various groups of member interests and of service to industry. This Institute has, within its organization, four divisions and fourteen technical committees--each interested in a separate put very definite subject, and each covering a phase of mining engineering interest. These vary from geology and the geophysical methods of prospecting, to the physics of the structure of metals, truly "from the mine to the consumer"-from the preparation for mining to the final use of that which has been mined.

Jan 1, 1931

By Walter Loel

THE application of aerial photographs to all phases of geologic mapping is set forth, indicating the advantages to be gained in different types of country and under varying climatic conditions. Methods of field and office procedure are given from a geological point of view, as well as suggestions regarding the best methods of aerial mapping for different uses and under varying field conditions, including the study of submarine geology. Aerial photographs with accompanying geologic maps are shown to illustrate the appearance from the air of different geologic features under varying climatic and topographic conditions.

Jan 1, 1938

By J. B. Clark

An exploratory study of the 60 wt pct Mg and 80 wt pct Mg sections of the solid constitution in the magnesium-rich region of the Mg-Al-Ca-Zn system was undertaken. The objective of the investigation was to determine the general configuration of the phase fields with respect to the magnesium solid solution in this complex system. The 335°C (635°F) tetrahedron was selected for study because the solid constitutions of the bounding ternary systems—Mg-Al-Zn,1 Mg-A1-Ca,2 Mg-Ca-zn3—were well known and, at least in these ternary systems, diffusion was rapid enough at 335°C for equilibrium to be reached fairly rapidly. Metallography and powder X-ray diffraction were selected as the best corroboratory methods for determining the solid phase equilibria. A total of forty-six quaternary alloys on the 60 wt Mg and 80 wt Mg sections were prepared, annealed to equilibrium at 335°C, and the phases present identified. Singly sublimed (99.99 pct) magnesium, electrolytic (99.99 pct) zinc, high-purity (99.99 pct) aluminum, and USP calcium were alloyed in graphite crucibles under a chloride flux and chill cast into a split graphite mold. Alloy samples were sealed under argon in Pyrex vials and annealed at 335°C ± 1/2° for a minimum of 500 hr. At the conclusion of the anneal, the alloy samples were quenched rapidly in ice water. Standard metallographic procedures for magnesium alloys were used. Powder X-ray diffraction patterns were taken on a G. E. Camera with a diameter of 14.32 cm using nickel filtered copper radiation. The phase equilibria in the 60 wt pct Mg section of the 335°C (635°F) tetrahedron is shown in Fig. 1. The complex equilibria in the zinc-rich region were not accurately determined and are shown only tentatively with dotted lines. The equilibria of the three bounding ternary 335°C sections from pure magnesium to 60 wt pct Mg are also shown as though folded away from the tetrahedron. The 80 wt pct Mg section has the same configuration of phase fields as that shown in Fig. 1. Thus it is reasonable to conclude that in higher magnesium sections, the same relative configuration of phase fields is maintained though the relative proportions of the individual phase fields may change slightly as the magnesium solid solution is approached. Note that all the ternary phases present in these ternary diagrams enter into the quaternary equilibria with the exception of the phase of the Mg-Al-Zn system which becomes unstable with the addition of as little as 1/2 pct Ca. No quaternary intermetallic phases were found. No liquid phase was detected in any of the quaternary alloys annealed at 335°C suggesting that if a quaternary eu-tectic exists, it must lie between 335°C and 339°C, the temperature of the ternary eutectic in the Mg-Al-Zn system.

Jan 1, 1962