Search Documents

By P. M. Blair

This paper presents numerical solutions of the equations describing the imbibition of water and the countercurrent flow of oil in porous rocks. The imbibition process is of practical importance in recovering oil from heterogeneous formations and has been studied principally by experimental means. Calculations were made for imbibition of water into both linear and radial systems. Imbibition in the linear systems was allowed to take place through one open, or permeable, face of the porous medium studied. ln the radial system, water was imbibed inward from the outer radius. The effects on rate of imbibition of varying the capillary pressure and relative permeability curves, oil viscosity and the initial water saturation were computed. For each case studied, the rate of water imbibition and the saturation and pressure profiles were calculated as functions of time. The results of these calculations indicate that, for the porous medium studied, the time required to imbibe a fixed volume of water of a certain viscosity is approximately proportional to the square root of the viscosity of the reservoir oil whenever the oil viscosity is greater than the water viscosity. Results are also presented illustrating the effects on rate of imbibition of the other variables studied. INTRODUCTION The process of imbibition, or spontaneous flow of fluids in porous media under the influence of capillary pressure gradients, occurs wherever there exist in permeable rock capillary pressure gradients which are not exactly balanced by opposing pressure gradients (such as those resulting from the influence of gravity). The importance of such capillary movement in the displacement of oil by water or gas was recognized in early investigations and described by Leverett, Lewis and True in 1942.1 Methods advanced by these authors for studying the process using dynamically scaled models were rendered more general and flexible by the research of later workers.2"4 The influence of capillary forces in laboratory water floods has also been discussed by several authors.6 While imbibition plays a very important role in the recovery of oil from normal reservoirs, Brownscombe and Dyes7 pointed out that imbibition might be the dominant displacement process in water flooding reservoirs characterized by drastic variations in permeability, such as in fractured-matrix reservoirs. In water-wet, fractured-matrix reservoirs, water will be imbibed from fractures into the matrix with a countercurrent expulsion of oil into the fractures. If the imbibition occurs at a sufficiently rapid rate, a very successful water flood can result; if the imbibition proceeds slowly the project might not be economically attractive. Scaled-model studies have demonstrated the vital importance of imbibition in secondary recovery in fractured reservoirs. It is therefore important in the evaluation of waterflooding prospects to develop a thorough understanding of the quantitative relationships of the factors which control the rapidity of capillary imbibition. The imbibition process serves reservoir engineers in still another important way by providing a technique for studying the wettability of reservoir core samples. Such experiments are usually conducted by observing the rate of expulsion of oil or water from core samples submerged in the appropriate fluid. Several papers have been 'published on the experimental techniques involved?? Although Handy has recently published a method for calculating capillary pressures from experiments with gas-saturated cores, it has not yet been possible to deduce quantitative information regarding water-oil relative permeability and capillary pressure characteristics of the rock from the experimental results. Thus a technique is needed for studying the quantitative dependence of imbibition rate on oil and water viscosity, initial water saturation, relative permeability-saturation, and capillary pressure-saturation relations. The development of such information, including saturation and pressure profiles by laboratory experiments, would be very difficult. However, recent advances in the applica-

Jan 1, 1965

By T. KIRKE ROSE

A Discussion of the paper by H. O. Hofman and M. G. Magnuson, read at the Lake Superior meeting, September, 1904. (British Columbia Meeting, July, 1905.) T. KIRKE ROSE, London, Eng. (communication to the Secretary*`) :-The authors have shown that, under certain conditions, the rate of dissolution of gold by chlorine and bromine is re¬duced by the addition of 10 per cent. of silver to the gold, and that the action is almost stopped when the silver amounts to 30 or 40 per cent. of the alloy. Even if full recognition is given to the practical way in which the work was done, how¬ever, it is to be regretted that Prof. Hofman and Mr. Magnuson did not determine the temperature at which the experiments were carried out. From the details given it may be inferred that the temperature was raised by chemical action by about 20° C. when 21 g. of sulphuric acid were added, and that the mixture was then slowly cooled down during the experiment. When bromine or very weak chlorine solutions were used, there could not have been any perceptible heating action. As the action of both chlorine and bromine is aided by heat, it follows that the stronger solutions of chlorine were given an unfair advantage over the weaker solutions and over bromine. If the temperature had been the same in each case, I do not think that the conclusions given oil p. 432 of the Bi-Monthly Bulletin, March, 1905, 1 would have been found to be justified. (This is speaking generally. In barrel-treatment the conditions are similar to those in the experiments.) The superior speed of bromine as compared with chlorine at equivalent strengths is not yet disproved, and the differences noted between strong and weak solutions of chlorine may have been largely a function of the temperature. Moreover, the authors used somewhat coarse particles of gold

Sep 1, 1905

By J. K. Elliott, P. H. Kelly

Many engineering functions such as surface metering work and laboratory compressibility check points involve the use of liquid densities of light hydrocarbon mixtures at various pressures and temperatures. However, at the present time, no simple reliable method exists for determining density variation, particularly if the composition of the liquid is unknown. Consequently, a study was undertaken to develop and present a simple and accurate method of predicting density variation of a light hydrocarbon liquid with pressure and temperature, knowing only the density of the liquid at some condition. The experimental liquid compressibility data from API Project 37 by Sage and Lacey' have been considered to be accurate within 0.5 per cent and cover a wide range of pressure (14.7 to 10,000 psia), temperature (100" to 400°F) and molecular weight (up to 150). From these data, a set of liquid density curves, which relate density to pressure, temperature and molecular weight, was developed. These curves make it possible to predict density variation with pressure and temperature. Compared to extensive laboratory compressibility data on a complex, light hydrocarbon liquid, the use of the liquid density curves resulted in an average error of less than 0.5 per cent. Based on the results of this analysis, it is concluded that the set of liquid density curves developed from the data of Sage and Lacey provides an accurate and simple method for predicting the density variation of light hydrocarbon liquids when the density at some condition is known. These curves should be very helpful in many engineering calculations, particularly in the surface metering of light hydrocarbon liquids. INTRODUCTION Many situations arise in field and engineering laboratory work, such as reservoir engineering studies, check of experimentally determined laboratory data and orifice flow-meter formulas, where liquid density factors at various pressure-temperature conditions are required. Also, the need for accurate light hydrocarbon liquid information has become more important with the advent of miscible-type displacements for secondary recovery purposes in oilfield operations. Several reliable methods are available1 - "or determining the density of liquid hydrocarbons if the composition of the liquid is known. However, there is a definite lack of methods for accurately determining the variation of density when the composition of the liquid is unknown. The purpose of this study is to review the various methods for determining hydrocarbon liquid densities and to develop a simple and reliable method of determining variation in density of light hydrocarbon liquids with pressure and temperature when the compositio~n of the liquid is unknown. METHODS FOR DETERMINING DENSITY OF LIQUIDS OF KNOWN COMPOSITION Sage, Lacey and Hicks' have proposed a method to predict the density of light liquid hydrocarbons by using partial molal volumes. Data are available on experimentally developed partial liquid volumes of hydrocarbons over a rather limited range of temperature, pressure and composition. The partial mold volume method has proved satisfactory for determining the density of some hydrocarbon liquids when the composition is known. Within the range covered in the Sage, Lacey and Hicks1 data, the results agree within about 3 per cent of the experimental values. Hanson mentions the limitation of this method to a composition range of approximately 10 per cent by weight of methane, which will not allow this correction to cover most low molecular weight-light hydrocarbon liquids. Standing and Katz2 studied data on light hydrocarbon-liquid systems containing methane and ethane at high temperature and pressure and have presented a method for determining liquid densities, assuming additive volumes for all components less volatile than ethane and using apparent densities for methane and ethane. The compressibility and thermal-expansion curves used by Standing are based on assumptions that compressibility of a hydrocarbon liquid at temperatures below 300°F is a function of the liquid density at 60°F and that thermal expansion of the liquid is affected little by pressure. The information required to use this technique with an example problem is furnished by Standing.' Hanson eports an average error of - 0.5 per cent using the method of apparent densities in calculating liquid densities of several volatile hydrocarbon mixtures. However, as implied, the apparent density method is not applicable for liquid density calculations when the composition of the liquid is unknown. Watson- as presented a method

By H. H. Rachford, J. Douglas, D. W. Peaceman

A numerical solution of equations describing two-phase flow in porous media shows promise in providing a technique for predicting the displacermet from satlds of oil by water or gas. The description includes the influence of relative permeability, fluid viscosities and densities, graviry, and capillary pressure, and, tholrgh tested ortly for two-dimensional cases, should be eqlmlly applicable in three-dimensional geometry. Two memorical methods ore presented: the first method is quite general in its applicability; the second method can be used only with certain types of boundary conditions but requires less computing. Comparisons of computed results with data from Inhoratory models are presented. These data were taken on a water flood of a strarified model and on water floods of a five-spot model for favorable and unfavorable mobility ratios. On the stratified model, excellent agreement with recovery at breakthrough was obtained; agreement with recovery after breakthrough was poor. In the five-spot model, good agreement was obtainecl with recovery at and after breakthrough. The purpose of this paper is twofold: first, to present a reservoir engineering method requiring knowledge only of rock geometry and the normally measured rock and fluid properties for calculating the multi-dimensional flow of water displacing oil from porous, water-wet rock containing connate water; and, second, to investigate the validity of the method by comparing results of calculations with previously observed displacements in laboratory models. The availability of such a verified technique of reservoir analysis would afford major advantages. First, it would demonstrate that the fundamental macroscopic concepts of two-phase fluid mechanics, i.e., relative permeability and capillary pressure, yield an adequate description of the physical process. Also, since most reservoir rocks appear to be water-wet and contain connate water along with oil, it would provide a method of technical and economic value for calculating the course of oil displacement by water directly from measured reservoir and fluid properties. It is important to emphasize that the calculation is subject only to the limitations of detail and precision of reservoir information, but not to limitations introduced by simplifying assumptions. Further, it would providc almost the only means of examining the influence of factors such as the size and extent of reservoir inhomogeneities and uncertainties in the basic reservoir data. Knowledge of this influence is essential in stating quantitatively the detail required to define a reservoir and in establishing the relation between the uncertainty in the definition of reservoir properties and the reliability of predicted performance. Moreover, in the process of solving a particular problem much detailed information would become available about the displacement process. For example, at each point in the reservoir for all stages of the displace ment. the calculations would yield not only the water and oil saturations but also the direction and magnitude of fluid velocities and the local fluid mobilities. Such dctail is potentially of great value in giving insight into the mechanics of particular displacements. The development of such a method has long been the goal of research in the application of numerical an-alysis to petroleum reservoir enginecrinz. The most complete treatment of the displacement process published to date is that of Douglas. Blair, and Wagner,' which, however, was limited to flow in a single dimension. The method presented in the present work is hascd on the numerical solution of a finite difference analogue of the multi-dimensional differential system describing the displacement process. Although current work has considered only displacement of oil by water from water-wet sands, the differential system for other immiscible displacements, such as gas displacing oil with which it is in phase equilibrium, is quite similar. It should therefore be expected that the technique described will be applicable to displacement by gas as well. The description of the simultaneous flow of fluids through porous media in terms of relative perrncability and capillary pressure has been adequately discussed in the literature and standard textbooks. Sec, for exampje, Muskat. Chapter VII.'

By J. C. Griffiths, D. W. Bennion

A mathematical model, which does not assume a priori that stratification exists, but was designed to test for the stratification was developed. The model segmented the reservoir horizontally into areas of common variance, then divided it vertically into strata (if strata were present). Next, trend surface techniques were used to determine the lateral extent and variation of each stratum. The model was tested on two reservoirs (sandstone and limestone) using porosity as the reservoir rock property. The sandstone reservoir contained approximately 60,000 samples from 2,000 cored wells, while the limestone reservoir had approximately 24,000 samples from 430 cored wells. Within the areas of common variance tested, the model was able to distinguish four separate lithological units or zones in the sandstone reservoir, four in the Marly section and seven in the Vuggy section of the limestone reservoir. INTRODUCTION To accurately predict the movement and production of fluids from a reservoir rock, it is necessary that the reservoir engineer have a knowledge of the rock properties and their distribution throughout the reservoir. For this study, a reservoir rock is defined as a solid containing interconnecting holes or voids which occur relatively frequently and are dispersed within the rock in a regular or random manner. The fraction of bulk volume that these interconnecting voids occupy is called porosity. The rock must also possess sufficient permeability to allow fluids to move through it and it may be composed of one or more strata or lithological units. A stratum or lithological unit as defined in this study is a body or volume of reservoir rock whose properties are so distributed that its lateral and vertical extent can be traced throughout or through a portion of the reservoir. Operationally, the existence of strata are question- able unless the variance within strata is less than among strata. Within the past few years computers have been widely used as a tool for calculating movement and production of fluids from reservoirs. Most prediction models require some type of a mathematical description of certain reservoir rock properties. In the past, most of these models have been relatively simple. Some have assumed vertical variation but no lateral variation, while others have assumed lateral variation but no vertical variation. In general, most of these models have not used functional relationships to predict reservoir rock properties as functions of position. The object of this study was to develop a model which would predict lateral and vertical variations of reservoir rock properties. Since samples are usually available from only a small portion of the total reservoir rock, it seemed logical that if measurements from these samples were to be used to infer the properties of the actual reservoir, the data should be treated statistically as a sample from the total population (reservoir). Therefore, the model developed in this study to predict reservoir rock properties was a stochastic model. The model was tested using porosity (a macroscopic reservoir rock property) measurements from two reservoirs — the first, a sandstone reservoir from which 60,000 samples were obtained; and the second, a limestone reservoir with 24,000 samples. Several investigators have proposed methods to determine the vertical and areal variation of a reservoir rock property. Stiles: Dykstra and Parsons 2 and Suder and Calhoun3 have all developed waterflooding prediction techniques which assume vertical variation but no lateral variation. Stiles developed a method to segment a reservoir arbitrarily using frequency distribution. Law4 suggested that porosity has a normal frequency distribution and that permeability has a log-normal frequency distribution. Elkins and Skov 5 proposed that when a reservoir is segmented vertically, the

Jan 1, 1967

By B. A. Eaton, R. H. Jacoby

This paper presents the depletion-performance correlations developed using data from PVT studies and well-completion tests of 27 rich gas-condensate and volatile-oil reservoir fluids. The PVT behavior for each fluid war determined experimentally in the laboratory, and the depletion performance of each fluid was then calculated. Well-completion test data consisting of reservoir pressure and temperature, initial total gas-oil ratio, and stock-tank oil gravity were used with the depletion-performance data to develop general performance correlations. Three correlations are presented. The first equation shows the empirical relation of gas in place per barrel of hydrocarbon pore space with reservoir pressure and temperature, and initial total gas-oil ratio. The second equation is the correlation of stock-tank oil in place per barrel of hydrocarbon pore space. The third equation relates stock-tank oil production (to 500-psia depletion pressure) with pressure, temperature and oil gravity. All three correlations are also presented in convenient graphical form. Gas production to 500-psia depletion pressure is approximately 92.6 per cent of the gas in place for each fluid, so no correlation was developed for gas production. INTRODUCTION The rate of discovery of shallow, low-pressure and low-temperature oil reservoirs in the United States has been declining in recent years. For this reason, the search for oil has gone to greater depths where high pressures and temperatures are encountered. A high-pressure and high-temperature reservoir is the environment in which many rich gas condensates and highly volatile oils are found. Because of this trend, the performance prediction of such reservoirs has become an important task of the reservoir engineer. The need and usefulness of a performance correlation based on field data that are available from the usual well-completion tests have previously been established. These earlier attempts have shown that the phase behavior of rich gas-condensate systems and volatile-oil systems can be correlated with fluid properties, pressure and temperature. However, very little information on gas-condensate depletion performance5 was available at the time of these earlier attempts. The availability of more recent data has made possible the development of an improved correlation. The data, as listed in Tables I and 2, are for 25 gas-condensate and two volatile-oil systems that were studied. The problem was to correlate the data for in-place fluids and the production data with the initial total gas-oil ratio, initial reservoir pressure and temperature, and stock-tank oil gravity. These correlations were obtained by multiple regression analysis, whereby the data were fitted to an equation by the method of least squared error. BASIS OF THE CORRELATIONS 1. The data used in the development of these correlations were obtained from depletion-performance calculations6 and well-test or production measurements. 2. All of the independent variables used in the correlations are available from the usual well-test completion data. 3. The reservoir volume considered is 1 bbl of hydrocarbon pore space (HCPS). 4. The gas-oil ratio used is the total standard cubic feet of gas (at 14.7 psia, 60F) coming off the entire separator train per barrel of stock-tank oil. This minimizes the effect of separator conditions which might vary from system to system. 5. The correlated pressures are the actual reservoir pressures which might or might not be the saturation pressure of the reservoir fluid.

Jan 1, 1966

By John M. Campbell, W. E. Portman

A series of correlating charts have been prepared to enable the field engineer to predict the amount of stock tank fluid produced by stabilization of first stage separator fluid. The charts shown are particularly convenient for estimating the relative effect of temperature and pressure in economic studies. Further work is planned to investigate the factors affecting stage separation' yo supplement this preliminary work. The direct correlation of separation variables is dictated as a convenience to eliminate the trial and error calculation necessary when using the standard flash vaporization equations. These are obtained by a material balance using the equilibrium vaporization ratio K, and have appeared in the following, or similar. form many times in the literature. where La = mols of any component n in the separator liquid Ko — equilibrium vaporization ratio for any component at separator pressure and temperature Fa = mols of any component n in the feed Vn = mols of any component n in the vapor V = total mols of separator vapor These equations may of course be effectively and accurately solved by use of digital and analog computers. However, these are not usually readily available in field offices and the need often arises for fast results during routine operational problems. Consequently, many methods have been devised in an attempt to simplify the basic calculation.2-14 The methods proposed are generally satisfactory, but do not eliminate trial and error methods and the necessity of subsequent calculations to obtain the answer in volume terms. The purpose of this work. therefore, was to develop accurate charts that would give the result directly in gallons. When using stage separation the recoveries would be lower than those shown, for stabilization usually gives about 95 + per cent recovery on the potential stock tank components in the separator liquid. The recoveries are shown in terms of a 14 psi Reid Vapor Pressure product which has a true vapor pressure of 14.7 psia at 98°F. Consequently, this product represents a stable stock tank liquid under normal storage conditions. To estimate natural gasoline re- coveries by stabilization the volume shown may be multiplied by 1.20 for 18 Ib RVP natural gasoline and 1.36 for 26 lb RVP natural gasoline. PROCEDURE The five analyses shown in Table 1 were chosen since they were representative of wellstream compositions often found and had almost the same propanes plus liquid content, expressed in gallons per 1,000 std. cu ft of wellstream. The distribution of the components though is widely variant. A temperature range of 0-100°F. and a pressure range of 200 to 1,250 psia was chosen inasmuch as most separations fall within these limits The K values used were modified values of those originally published by Katz and Hachmuth.' In the range chosen these have generally given good results when predicting fluid recoveries. The choice was somewhat arbitrary, for the authors' personal experience has shown that

Jan 1, 1957

By E. E. Schumacher

IN a laboratory devoted to the furtherance of the science of communication, the breadth and variety of the problems encountered are challenging to a metallurgist. In my own long association with the Bell Telephone Laboratories, our metallurgical group has dealt with a vast number of alloys, both ferrous and nonferrous, and with many materials in the border range of metallic properties., The objectives of our design engineers embrace every phase of telephony, and the properties they desire in metals are generally unusual, frequently unique, and often conflicting. Commercial alloys have not always been available with properties to meet a special requirement in the telephone plant, and many alloys have had, therefore, to be custom-made. Anyone who has had the opportunity to observe the results of tests of all types on numerous such alloys, both commercially and specially produced, or who has taken part in the development of an alloy of some necessary, but new or unusual combination of properties, could not fail to be impressed by the frequency with which a desired goal has been reached or adequately approached through the presence of decimal quantities of alloying elements. Nor could One fail to be struck by the occasions when, conversely, of a minute amount Of impurity element has rendered an alloy useful. It is no exaggeration to state that the content be- hind the decimal point often spells success or fail-ure, and the critical content is sometimes far to the right of the decimal point as I shall later illustrate. The great effects of small additions have long been recognized and have, in fact, been described by many investigators. The importance of the minute, however, cannot be overemphasized. Therefore, in this discussion, I propose to illustrate for you some of the startling instances, drawn primarily from our own experiences, wherein small, even vanishingly small, proportions of stranger elements in otherwise common aggregates have com-pletely changed the customary pattern of behavior. No one property has a monopoly as to being dis-proportionately affected by minor elements. Nearly all properties are affected, but there is time here to include only a selected few. I have chosen, there-fore, three of general interest: strength, magnetic, and electrical properties. I shall inquire into both the mechanisms and consequences of these disproportionate effects and try to share with you the fascination and challenge of this field. Strength Properties of Lead and Lead Alloys To illustrate the effect of the minute on strength properties I have selected lead and its alloys, with which we have worked extensively for many years. Lead has the advantages of being available in quantity in a state of high purity and of being fairly easy to melt and fabricate without contamination to any extent detectable by the spectrograph. It has the interesting disadvantages of recovery and recrystallization at room temperature. Whether I

Jan 1, 1951

By Walter Hull Aldridge

Much has been said about the foreseeable exhaustion of known mineral reserves-particularly in the United States. It is claimed that we are about to become a have-not nation insofar as certain essential minerals are concerned; and in this respect our position is often contrasted with that of the world as a whole, largely because we have drawn so heavily on our domestic resources during the last fifty years. As a matter of fact, the difference is not great if one takes a reasonably long-term view of the situation. No one denies that nature endowed the United States richer in mineral resources than any other equal area. It is granted that we have skimmed the cream of many kinds of minerals; but in a free international trade in minerals it would not be many decades before the richer deposits-at least the deposits easy of discovery throughout the world would be depleted to much the same degree as those in the United States today. For it is a fact that the problem of satisfying the needs of our industrial society for minerals is fundamentally worldwide in scope. The singular and significant attribute to all minerals is that there is but a single crop. Forests can be grown, but mineral deposits can be replaced only by finding new ones. Thus, one of the vital tasks of the mining engineer, the petroleum engineer, and the geologist is to find these new mineral resources. Another task is to devise means and methods for the exploitation of, at costs that are economic, low-grade deposits and those deeply buried in the crust of the earth. The first need, however, is to find the deposits in the ground. If the assumptions of those who today fear an early exhaustion of all deposits are valid, the outlook for continued material and social progress is gloomy indeed. I take a more optimistic view, for it is my belief that vast new sources of needed minerals will have come to light before our known resources are gone. The real question is whether the outside layer of the crust of the earth that is accessible to engineers contains adequate mineral deposits; and whether engineers can find those deposits. The answer must be based on geologic science, geologic fact, and mining history. Every continent, and almost every country, has yielded minerals of industrial utility in substantial quantity. Mineral deposits are widespread. Geologists know the conditions that were favorable to the occurrence of ores and the types of rocks in which various kinds of ores may ordinarily be found. They know that such rocks occur over broad regions of the earth's surface. They also know that in large areas rocks that are potential carriers of ores are covered and concealed by material of entirely different character. Such cover may consist of lava flows, layers of volcanic ash, or beds of material washed down from the surrounding mountains. Sometimes those covers are thick, sometimes relatively thin. But men well-qualified to pass judgment are sure that concealed deposits, large in number and in size, exist close enough to the surface to make exploitation practical. Only by actual penetration of the surface can this contention be proved, but to conclude otherwise would be to ignore the laws of probability and to deny the over-all consistency of nature. The task of probing the crust of the earth to determine the location of these deposits, and to obtain some notion of their size and quality, poses serious problems. However, they should not be beyond human solution. Much more research must be done in analyzing and explaining the laws of ore deposition. New tools, in the shape of techniques and methods and of mechanical and electrical devices and instruments, must be developed. But no reasonable person can doubt that these objectives will be achieved. As the need becomes increasingly pressing, scientists and engineers will supply the imagination and the ingenuity that will provide the solution. The time and effort thus far devoted to the development of methods for locating hidden ore bodies have been pitifully meager. Energetic investigation of the subject of applied geophysics is essential to the success of the mineral industry, and I have no hesitation in predicting that effective techniques will be found and successfully applied. Twenty-five years ago the petroleum industry

Jan 3, 1950

By H. F. Winham

The history, development, subsurface geology, production, economics and estimated reserves are discussed in this paper. The Magnolia structure is an anticline with a known maximum structural relief at 372 ft., and the areal extent of the producing acreage is 4494 acres. Production is obtained from the Smack-over oölitic lime and 116 successful wells have been drilled. The field, which was developed on 40-acre spacing, has been under strict control. It is believed to be producing with a strong water drive, To date it has produced more than eighteen million barrels and the estimate of ultimate recovery is 220 million barrels. Early History The Magnolia field is in colurnbia County, Arkansas, T. 17 s., R. 19 and 20 W. Various geologists had long been interested in this general area, and as early as 1921, John F. Magale was able to define a surface structure. The first wildcat, one of the first in Columbia County, was drilled in 1923 by Mid-States Oil Co., in sec. 10, T. 17 S., R. 20 W. This well was about 11/2 miles northwest of the Kerlyn oil Company's discovery well and was based on surface geological work done by Jewel and Dobie. Subsequently, several shallow wells that were not carried below the Upper Cretaceous beds were drilled in the immediate area of the discovery well, but none of them contained any commercial showings of oil Or gas. In the latter part of 1935, Elam and Magale (or Southwood) Garrett NO. I was located in sec. 13, T. 17 S., R. 20 W., 3/4 mile east of the discovery well. It was drilled to a total depth of 4018 ft. in the lowermost Glen Rose beds but failed to obtain any showings of oil or gas. Interest had been stimulated in this general area, however, by the discovery of several oil fields, mainly Glen Rose oil production in the Rodessa field in Louisiana in 1935, Smackover lime productioil in Snow Hill in May 1936, production from the Cotton Valley formation in Schuler in 1937, and Smackover lime production from the Buckner field in November 1937. With this background and subsequent seismic work, which was carried on partly because the old shallow wells drilled in the township had shown evidence of closure in the Upper Cretaceous beds, the discovery well, Kerlyn Oil Company's Barnett No. I, Sec. 14, T. 17 S., R. 20 W., was originally projected to a total depth of 6300 ft., to test the equivalents of the Morgan sands of the Cotton Valley series, then producing at Schuler. The well was carried to a depth of 6325 It. and tested the objective beds without finding commercial production. In the meantime, however, one well had found production in the Jones sand and another in the Smaclrover lime at Schuler. Kerlyn immediately made arrangements to deepen the Barnett well to the Smackover lime. The top of the Smackover lime was encountered at 7618 ft. and the well

Jan 1, 1943

By H. F. Winham

The history, development, subsurface geology, production, economics and estimated reserves are discussed in this paper. The Magnolia structure is an anticline with a known maximum structural relief at 372 ft., and the areal extent of the producing acreage is 4494 acres. Production is obtained from the Smack-over oölitic lime and 116 successful wells have been drilled. The field, which was developed on 40-acre spacing, has been under strict control. It is believed to be producing with a strong water drive, To date it has produced more than eighteen million barrels and the estimate of ultimate recovery is 220 million barrels. Early History The Magnolia field is in colurnbia County, Arkansas, T. 17 s., R. 19 and 20 W. Various geologists had long been interested in this general area, and as early as 1921, John F. Magale was able to define a surface structure. The first wildcat, one of the first in Columbia County, was drilled in 1923 by Mid-States Oil Co., in sec. 10, T. 17 S., R. 20 W. This well was about 11/2 miles northwest of the Kerlyn oil Company's discovery well and was based on surface geological work done by Jewel and Dobie. Subsequently, several shallow wells that were not carried below the Upper Cretaceous beds were drilled in the immediate area of the discovery well, but none of them contained any commercial showings of oil Or gas. In the latter part of 1935, Elam and Magale (or Southwood) Garrett NO. I was located in sec. 13, T. 17 S., R. 20 W., 3/4 mile east of the discovery well. It was drilled to a total depth of 4018 ft. in the lowermost Glen Rose beds but failed to obtain any showings of oil or gas. Interest had been stimulated in this general area, however, by the discovery of several oil fields, mainly Glen Rose oil production in the Rodessa field in Louisiana in 1935, Smackover lime productioil in Snow Hill in May 1936, production from the Cotton Valley formation in Schuler in 1937, and Smackover lime production from the Buckner field in November 1937. With this background and subsequent seismic work, which was carried on partly because the old shallow wells drilled in the township had shown evidence of closure in the Upper Cretaceous beds, the discovery well, Kerlyn Oil Company's Barnett No. I, Sec. 14, T. 17 S., R. 20 W., was originally projected to a total depth of 6300 ft., to test the equivalents of the Morgan sands of the Cotton Valley series, then producing at Schuler. The well was carried to a depth of 6325 It. and tested the objective beds without finding commercial production. In the meantime, however, one well had found production in the Jones sand and another in the Smaclrover lime at Schuler. Kerlyn immediately made arrangements to deepen the Barnett well to the Smackover lime. The top of the Smackover lime was encountered at 7618 ft. and the well

Jan 1, 1943

By E. H. Bronson

PROPERTY of Malartic Gold Fields Ltd. is situa-ated in the great clay belt in the northern part of the Province of Quebec. This belt represents the floor of the glacial lake Barlow-Ojibway. The clay blanket has a gently rolling, almost flat surface, with here and there projecting knobs and ridges that outline the large irregularities of the surface on which the clay was deposited. At irregular intervals glacial eskers dominate the landscape. The ore-bearing country rock is covered by strata of clay, sand, and silt to a depth varying to 40 ft. There are serious structural problems when it is necessary to place loads of unequal intensities on this surface to support buildings and machinery for a modern mining plant. Earlier mining companies and their engineers paid little attention to the science of soil mechanics, partly because they believed it unnecessary and partly because they knew little of the subject. The results are evident in some of the tottering structures in older camps. Careful analysis of soil problems is well worth-while, since cost of foundations may vary from 20 to 50 pct of the final cost of a structure. Low operating and maintenance costs can be achieved only in this way. If it is definitely established that a plant will be in operation for only a few months, this limited time factor will probably influence the design of the foundation, and rightly so. If sensitive and complickted equipment is to be mounted on these foundations and the plant is to operate for several years, there should be a thorough study of foundations and a very careful design. A familiar problem is presented by the difficulty of operating a permanent plant originally designed for a few months' work. The engineer must beware of these hazards and disassociate himself from them if he cannot prevail on the promoter to spend the proper amount for a thorough foundation study. Laws of certain provinces and states hold the engineer equally responsible with the contractor for any 'damage that may be caused to building through inadequate study-ignordnce of the facts is no excuse in the eyes of the law. Types of Soil: The engineer should be familiar with such terms as silt, clay, peat, and varved clay, as well as perpafrost, especially if he is to work in the far northern reaches of the country. He should also be familiar with soil attributes such as porosity, texture, consistency, permeability, compressibility, consolidation, and shearing resistance. The design of any foundation requires an accurate knowledge of the physical properties and location of the soils involved. Older textbooks on the subject outline various empirical methods to determine the carrying power of soil. Tables are given in reference books. The modern ehgineer should be wary of these modes of thinking. He should analyze his problem carefully, calculate to what depth of soil the loads may be transmitted, and then check the bearing value of all soils to that or greater depths. If the strata are water-carrying, he must determine the possibility of this water being accidentally re-

Jan 1, 1958

By AIME AIME

LEROY SALSICH has had 37 consecutive years of operating and executive experience in the Lake Superior iron region during 35 of which he has been a member of the A.I.M.E. His recent election as an institute Director to represent the iron and copper country therefore brings to the Board a man long known throughout the area that he represents and well acquainted with the history of the Institute. Mr. Salsich is a native of the area in which his professional life has been spent, having been horn at Hartland. Wis., and graduating from the state university's college of engineering in 1901. A call had come to the college from the Lake Superior Consolidated Iron Mines, at Duluth.

Jan 1, 1938

By AIME AIME

THE autumn is the time that nearly all the special groups within the broad field of the Institute's activitives chose for their own special meetings. The big annual meeting in New York in February has its own special advantages, but to realize them involves sacrificing others. A meeting of a smaller group with the subjects brought up for discussion much more closely limited to a single field of interest has some advantages that a big general meeting cannot possibly have. And so the custom has gradually developed of having these smaller meetings in the autumn, at con¬venient places, so the men will not have to travel too far from the job to be present. Sometimes the meetings have for their field of interest a single phase of mineral technology, and are called divisional, and at other times they cover a diversity of topics that are locally important in that geographical area, and are then called regional meetings. Of the five meetings to be held this fall, four are divisional and one regional. Two of the divisional meetings are to be held in the same place at the same time, but with programs so arranged that they do not conflict.

Jan 1, 1930

By Henry M. Howe

(Cleveland Meeting, October, 1912.) Manuscript received Aug. 20, 1912. PROFESSOR RUFF'S most illuminating paper' describing his extremely valuable investigation of the carbon-iron equilibrium diagram assigns definite temperatures to certain very important lines in the diagram, viz.: the eutectic temperature EB (Fig. 1) and the " near-eutectic " temperature E'B', but without indicating clearly enough the reasoning which warrants these assignments. These temperatures are of such primary importance that it is well to indicate the apparent gaps in the reasoning, in the hope that they may be filled in. In his diagram, Fig. 1, the point X and the lines B'D'HI represent the experimental results reached by Ruff and Goecke; 2 AB, AEB, and SE represent the liquidus, the solidus, and the solubility of the carbon in solid austenite in the absence of graphite according to Gutowsky,3 AB being also in accordance with Spiecker's data;4 ,S'E' the solubility of carbon in solid austenite in the presence of graphite according to Ruer and Iljin; 5 GS the line A3 after Goerens and Meyer;6 I and EBC the true eutectic line as inferred by Prof. Ruff from Gutowsky's data. B'D' is the carbon content found in cast-iron which had apparently saturated itself with carbon in the presence of the graphite of the enclosing graphite crucibles in which the determinations were made. From its straightness and its sharp inflection near 6.67 per cent. of carbon, the carbon content of * Professor of Metallurgy in Columbia University. 1 Metallurgie, vol. viii., pp. 456 to 464 and 497 to 508 (1911). 2 Idem, vol. viii., pp. 417 to 421 (1911). 3 Idem, vol. vi., pp. 731 to 743 (1909). 4 Idem, vol. vi., p. 524 (Wüst) (1909). 5 Idem, vol. viii., pp. 97 to 101 (1911). 6 Idem, vol. vii., pp. 307 to 312 (1910).

Nov 1, 1912

By Roger M. Nendick

The recovery of precious metals from heap leach solutions can be accomplished by two processes: 1. The Carbon Adsorption Process 2. The Merrill-Crowe Zinc Precipitation Process A brief review of the relative process economics is made. Each process presents certain design considerations that must be addressed during the evaluation and engineering design for the project. Discussion is presented on the design criteria for each process.

Jan 1, 1984

By W. H. Bassett

W H. BASSETT was elected first vice-president at . the executive session of the new Board on Tues- day afternoon. Karl Eilers, H. Foster Bain, Thomas T. Read, and H. A. Maloney were respectively re-elected as treasurer, secretary, assistant secretary and assistant treasurer. The new Executive Committee will consist of W. H. Bassett, Chairman, and Richard Peters, Jr., H. C. Bellinger, E. De Golyer, Edgar Rickard. The Finance Committee will be J. V. W. Reynders, Chair- man, Henry Krumb and H. G. Moulton. George D. Barron was reappointed Chairman of the Admissions Committee, and F. Julius Fohs put in charge of the Papers and Publications Committee.

Jan 1, 1929

By AIME AIME

THE quarters provided for the session on Milling Methods, Monday afternoon, Feb. 17, were filled to capacity. Galen H. Clevenger presided and notables, such as A. W. Fahrenwald, A. O. Gates, F. A. Thomson, W. L. Zeigler and others who had not graced a milling meeting in New York in recent years, or per- haps even never before, were actually present and spoke "in person." The first paper, by A. W. Fahrellwald (T. P. 275), entitled "Classifier Efficiency ; An experimental Study," was summarized by the author, who clearly showed the inconsistency of determining the efficiency of a classifier by means of sizing tests, especially where the material classified consists of a mixture of minerals of different specific gravities. In place of sieve analysis the procedure recommended involves the use of a glass settling-tube which is considered to give ideal classification and thus serve as a standard against which mill classification will be compared and relative efficiency calculated. This procedure sounds logical. Perhaps the greatest difficulty may lie in securing an ideal classifier acceptable to every one.

Jan 1, 1930

By W. B. Heroy

ONLY through the mineral fuels can large amounts of energy be transported to great dlstances and stored for long periods for future use. Coal has the advantages over oil of greater safety of handling and smaller losses in storage. But oil is, in the present stage of technical advancement, the more economical source of liquid fuel for internal-combustion motors. No method for direct use of coal in such motors has been developed that can compete with petroleum products. The automoblle engine and the airplane motor are designed to make the most effective use of gasoline.

Jan 1, 1944

By Gerald Sherman

MINING asbestos ore by caving at Thetford Mines, Quebec, has been described in the Transactions of the Canadian Institute of Mining and Metallurgy in papers presented by the staffs of The Asbestos Corp. Ltd., in 1934, and Johnson's Co. Ltd., in 1941. The production by caving prior to 1949, in round figures, has been 14,500,000 tons of ore by The Asbestos Corp. and 5,500,000 by Johnson's Co. They are the only caving operations in asbestos at the present time. The Jeffrey mine of the Canadian Johns-Manville Co. at Asbestos, 40 miles southwest of Thetford, is well along in preparations for caving, and The Bell Asbestos Mines Ltd. at Thetford Mines, will follow their examples later. GERALD SHERMAN, Member AIME, is Consulting Engineer, Johnson's Co. and Canadian Johns-Manville Co., New York, N. Y. AIME San Francisco Meeting, Feb. 1949, and New York Meeting, Feb. 1950. TP 2828 A. Discussion (2 copies) may be sent to Transactions AIME before May 31, 1950. Manuscript received Nov. 2, 1949. Nearly all of the asbestos produced by the western hemisphere is mined in those districts of Canada. Since it has been the subject of a number of technical papers, this contribution is offered as a review of progress. Some introductory information seems appropriate, for few members of the American Institute of Mining and Metallurgical Engineers are familiar with the mineral, or how asbestos deposits differ from others in caving characteristics. Asbestos is found in peridotite, a basic intrusive rock irregularly altered to serpentine and erratically fractured, well enough to cave in bulk, but leaving many blocks of solid ore of all sizes scattered through the deposit. Chrysotile is the variety of asbestos produced in Canada. Its fibers are the most valuable commercially, having a good proportion of long fibers, strong, silky, flexible, and suitable for spinning. The fibers occur in all lengths, from the microscopic to 3 in., or more, the shorter are more abundant. Their values depend on length combined with other qualities noted above. They occur as veinlets filling fissures in the peridotite, with crystals compactly arranged in parallel across the cracks. They are sometimes lightly frozen to the walls but the partings are distinct, often marked by particles of magnetite adhering to the fiber ends. Sometimes they break away from the rock in slabs an inch or more in thickness. In wide fissures the fibers are not always continuous, the "broken fibers" being separated by lines of parting with occasional scattered grains of magnetite, which is an injurious mineral to be elirninated when possible. In addition to the chrysotile ''Cross fiber," some "slip fiber" is found in fault fractures in limited quantities of less valuable character. With the exception of the Asbestos Corp, ore, in which the content is said to be more uniform, asbestos is eccentrically distributed through the peridotite. It is the general impression that the higher grades are more often found in hard rock. There are rich pockets and leaner areas which range down through various grades to minor barren sections. Wholesale mining is necessary to make sure of recovering all the high grade for there are no reliable indications of its existence. Ore selection only appears in constructing assay-grade limits for caving. The mill yield of the Thetford ore body in 1934 was 6 to 10 pct of the ore milled, made up of all classes, with occasional runs up to 15 pct or so. Quotations for Canadian asbestos* are as follows: Per Ton No. 1 Crude (% in. and longer) $896 @ $960 No. 2 Crude (Y8 to % in.) 350 @ 545 Spinning (less than % in.) 204 @ 378 Other classes, price diminishing with length. Shorts or "refuse" 24 @ 46 • From Eng. and Min. Jnl., Nov. 1948. Asbestos of even superior quality for electric insulation is found in Arizona limestone. It is white, containing very little combined iron, but occurs only in small quantities.

Jan 1, 1951