Search Documents

By R. D. Lord

The search for the best practical means of storing sulfide bearing tailings, where there is no residual excess of carbonate material is discussed in this paper• Usually the sulfide content decomposes, with the aid of bacterial action, and the resulting sulfuric acid escapes, along with any heavy-metal solutes, through embankments that are usually porous to some degree• The problem is typified in the tailings of the uranium operations of Elliot Lake, Ont., where mining started some 20 years ago• The approach to tailings disposal paralleled the practice for other hydrometallurgical plants treating gold and base-metal ores• Impoundment areas were designed to retain solids, and a clear and neutral overflow was considered satisfactory practice• Now experience has shown that these areas, some of which have been idle for over a dozen years, release acids in seepage and overflows to an unacceptable degree• To protect natural water courses, neutralizing plants are operated wherever required• Lime slurry is fed continuously into the tailings outflows in a quantity sufficient to raise the pH to 8•5 and precipitate heavy metals that may be in solution• The objection to this procedure is that the plants will require servicing indefinitely, unless a better remedy is found• The problem differs only slightly from that common to base-metal concentrators in that here the ore has been leached with sulfuric acid for the recovery of uranium• Any native content of calcareous material has been digested, and only that added for final neutralization is available to maintain a pH unfavorable to bacterial activity• Chemical oxidation slowly lowers the pH and when this reaches a level of 4•5 or less, bacteria become active and greatly accelerate the formation of acid. The bacterial process is probably at least ten times as fast as the chemical oxidation• Location and Processing The operations referred to, uranium and one copper mine, are located at approximately 46°N and 82°W longitude• This is typical Canadian Shield country, a land of lakes, deeply glaciated and rocky, with sparse soil which supports mixed forest cover• Drainage is to Lake Huron, 25 miles to the south• Average temperature is 45°F, ranging from -40° to +95°F• Annual precipitation is 38 in•, about half of which is snow• The ore is Precambrian, quartz-pebble conglomerate, with mineralization in the matrix• From 5 to 10% pyrite is present• All known means of pre-concentration have been tested, but a bulk sulfuric acid leach has proved the most efficient. Tailings have from the outset been neutralized before release• Current practice is to add ground limestone to bring the pH to 4•5, and then lime to raise the value to 10•5• Environmental regulations have recently been increased and the foregoing meets the new standards• Separate measures are taken to precipitate radium• Remedial Measures Since the outstanding environmental problem is the oxidation of pyrite by bacterial action, the solution is to contain the products, or arrest the process• Given the ambient temperature, favorable half of the time, four items are essential to the activity• 1) Pyrite• 2) Moisture pH < 4•5. 3) Oxygen• 4) Bacteria• Removing any one of these out of the range of tolerance will bring the reactions under control• A variety of proposals considered, and a number tested for the arrest of the process, are: (a) render embankments impermeable, (b) provide an impermeable cover, (c) cover with an oxygen absorbing layer, (d) provide a vegetative cover, (e) flood the site, (f) remove pyrite from current tailings, (g) add excess limestone to current tailings, (h) poison the bacteria• Bank Seal-On existing impoundment areas, where the embankments are several thousand yards in length, it is believed that any program of injecting sealants can have small chance of success• However, a moisture barrier is an indicated specification for future construction, and this can be highly expensive• Surface Seal-Depending on the configuration of the deposit, the downward travel of water should be prevented, and oxygen excluded• Burying a plastic membrane just below the surface has been considered, as has the application of a liquid sealant that would penetrate the surface. The objection to these remedies is the excessive cost of dealing with large areas and the expectation of only temporary benefit as a result• Frost penetration is over 4 ft, and frost action breaks up asphalt paving and all but heavy concrete in a few years• Organic Layer-An oxygen-absorbing layer, such as bark fines from paper mills has been proposed as a surface treatment• Cultivated into the tailings such material might be expected to arrest subsurface oxidation for some years• Estimates are 100 tons per acre of bark fines, or 35 tons per acre of sawdust, and these enormous quantities do not so far give assurance of providing a long-term remedy• Vegatative Cover-Several obvious benefits would result from a good growth of grass or other vegetation on abandoned tailings• While restoring the natural green of the tract the growth would prevent wind-blown dust and reduce erosion• Subsurface oxidation should be reduced, as well as the upward movement of ground moisture as occurs in dry weather. To this end, considerable research and field testing has been carried out to arrive at a formula - a prescription which will provide a self-sustaining growth on the tailings surface, or at least one that would survive with reasonable maintenance attention. Many test plots have been run with different combinations of surface treatment and seed mixtures. Generally, by addition and close cultivation of limestone, lime, and fertilizers, technical success has been demonstrated• Plants with a high tolerance for acid soil seem the more hardy, and a pH above 3 is indicated so that nutrients can be absorbed• Recommendations are for 12 to 15 tons of

Jan 1, 1977

Accurate modeling of the semivariogram is an extremely important step in the geostatistical analysis of mineral deposits. Automatic fitting of a mathematical model is often possible but not necessarily desirable. Significant geologic and statistical information must be taken into account in the fitting process, which is not always available to the computer. Manual model fitting is, on the other hand, extremely time consuming. Interactive graphics are best suited to optimize the process. Many interactive methods are described, which are adapted to modeling semivariogram in one-, two-, or three- dimensional environments.

Jan 1, 1985

By Oscar H. Hershey

COMPLAINT has been made that in the literature of economic geology the work of the "company or practical" mining geologists does not get enough attention. I propose to attempt to overcome this com¬plaint in reference to one important lead-mining district, that of the Coeur d&apos;Alene in northern Idaho. Furthermore, I will assume that the reader is not so much interested in the geology of the district as in the methods of application used and incidents that have arisen in the work. All the important discoveries of ore in the Coeur d&apos;Alene were made without benefit of geology. Certainly I would not claim the reputed discoverer of the Bunker Hill mine as a fellow geologist. It appears also that the mines were operated quite successfully for many years without geological specialists, though doubtless certain properties were visited at long intervals by such men as Waldemar Lindgren. It was known that the ores occur in quartzite, graywackes and slates as stated by J. R. Finlay in 1903. (TRANS., VOL. 33.) He described the ore as occurring in typical fissure veins that occupy fault-planes of indeterminate displacement. The Bunker Hill lode was based on a definite fissure with the mineralization all on the hanging-wall side, extending as far as 300 ft. from the fissure.

Jan 1, 1933

By A. E. Lee

THE Blackwell Zinc Co., Inc., a subsidiary of the American Metal Co., Ltd., operates a horizontal retort zinc smelter at Blackwell, Okla. The plant has 14 furnace blocks of 800 retorts each, fired with natural gas on a 48 hr cycle. Over 13,000 tons of zinc-bearing material, chiefly sulphide flotation concentrates, are treated monthly to produce slab zinc and high lead-cadmium fume. In 1942 a program of rebuilding and modernizing the smelter was started. By 1947 furnace smelting capacity had been increased to a point where roasting and sintering facilities were inadequate, and it was necessary to purchase oxidized materials to supplement sinter production. The seven 210 ft Ropp roasters and three 42 in. x 44 ft Dwight-Lloyd machines then in use had been in service at least 20 years and were in need of major rebuilding. Thus it was entirely practical to consider all new equipment and a change of method rather than rebuilding and repairing obsolete units. A study of the problem indicated that roasting as such could be eliminated and roasting and sintering accomplished in one step by a modification of the Robson process,&apos; which had been used since the early 1930&apos;s by the National Smelting Co., Ltd., at their plants at Avonmouth, England, and Swansea Vale, South Wales. Francis P. Sinn, General Manager, Zinc Smelting Operations, The American Metal Co., Ltd., who was familiar with the practice in England, suggested the use of one large machine for the entire operation from concentrate to sinter. One step sintering appeared to best meet Blackwell&apos;s plant requirements and indicated substantial savings in labor, gas, coal, and repair costs. Choice of Machine Size The sinter machine size was set at 12x168 ft for a rated capacity of 540 tons per day. This tonnage, produced on a five day week, would meet the seven day requirements of the 14 furnace blocks. The one large machine was quoted at a lower cost than two or more 6 ft wide machines of similar total capacity. Further, the larger machine could be housed in a smaller structure and only one set of equipment for charge preparation and delivery and for disposal of sinter cake was needed. One machine on a five day week made possible a concentration of the skilled operating personnel and required less men than a plant including two or more machines and related equipment circuits. Fewer units of equipment meant less maintenance, and the two down days weekly allowed ample time to repair and, if necessary, to make up lost production. Experience had indicated better sintering quality and rates with larger masses of material, not only on wider machines, but also in deeper beds. The ratio of windbox perimeter to area for the 12x168 ft machine is 0.179, compared to 0.353 for a 6x102 ft machine and 0.617 for a 42 in. x 44 ft machine. This meant less air leakage with resulting fan power savings and less spoilage of charge along the pallet sides. Performance Initial operation of the new sinter plant was made in November 1951 and regular production attained late in December. The average product sinter output during 1952 and the first half of 1953 has been 18.2 tons per hr. The average for one month has been as high as 22.4 tons per hr. Considerable experimenting with varied operating conditions accounts in part for the below capacity — 24 tons per hr — average output, and work to further improve production rate continues. A typical sinter analyses is 66.0 pct Zn, 0.3 pct Pb, 0.1 pct Cd, 0.3 pct S, 8.0 pct Fe, 2.0 pct SiO,, 0.8 pct CaO, and 0.2 pct MgO. Use of this material has made possible increases in furnace burden and improved furnace operation over the former practice using sinter made from Ropp roasted concentrates. Better lead and cadmium elimination in sintering has permitted the furnace production of slab zinc lower in lead and cadmium. Anticipated economies of operation have largely been gained. The sinter plant is operated by seven men per 8 hr shift — one head operator, three equipment operators and three sweepers — plus one oiler on day shift only. While it has been necessary at times to operate seven days a week to produce the required sinter tonnage, the five day work week usually has been adequate. Consumption of natural gas for sinter bed ignition is 200,000 to 300,000 cu ft per day. Green Ore Sintering Practice The 30 to 31 pct sulphur content of the —200 mesh zinc concentrates is the fuel used to sinter the charge, no coal addition being required. In the feed to the machine, sufficient concentrates are added to crushed return sinter fines containing 0.3 to 0.5 pct sulphur to produce a charge averaging 5.0 to 6.5 pct sulphur. Since the return sinter used in Blackwell&apos;s practice is varied from — 1/2 to — 1/8 in., the actual sintering mixture of fine sinter and concentrates is somewhat higher in sulphur. The coarser sinter particles are too large to resinter and merely aid porosity in the sinter bed. The ratio of concentrates to return sinter in the charge ranges from about 1:4 to 1:5.5. Variations are based on the appearance of pried up bed sections, bed exit gas temperature trends, windbox suctions, and return sinter size. Sufficient sulphur must be used to obtain fritting of the charge into a soft sinter cake and to aid in the elimination of lead and cadmium. Excessive feed sulphur will result in partial slagging of the cake impairing porosity and prolonging sintering time.

Jan 1, 1954

By Donald F. Hammer, Donald W. Peterson

The Magma mine at Superior, Arizona, has produced over 13 million tons of ore yielding 1.5 billion pounds of copper. It is a mesathermal deposit, and, although the bulk of the ore has come from the Magma vein, most of the recent production has come from replacement deposits in limestone. The mine lies in a Precambrian and Paleozoic sequence of rocks that includes schist, diabase, quartzite, shale, and limestone; nearby, these rocks are intruded by igneous bodies of Mesozoic age that were probably the source of the ore-bearing fluids. Locally, these rocks are overlain by Cenozoic volcanic rocks and conglomerate. Layered rocks at the mine dip eastward about 30°. The area is extensively faulted, and surface faults are grouped into an earlier east-trending set and a later northtrending set. An additional set of diagonal faults that trends northwest and northeast is recognized underground. The east-trending Magma vein-fault, with its splits and branches, is the principal mineralized structure of the district. The bulk of the ore occurs in large ore shoots that plunge steeply westward and are sporadically connected by irregular ore shoots dipping gently eastward. The main ore controls apparently are selective zones of permeability related to the transverse faults. A bed of crystalline limestone near the base of the Martin Limestone (Devonian) is the host for the replacement ore bodies-discontinuous tabular pods dipping eastward parallel to the bedding. Selective permeability is again the apparent ore control, caused both by local hydrothermal solution of limestone and by deformation along faults. The principal copper minerals in the vein are chalcopyrite, bornite, enargite, tennantite, chalcocite, and digenite; these minerals vary in abundance according to a distinct zoning pattern. The upper part of the mine yielded considerable zinc as sphalerite, and the oxidized zone was rich in silver. The chief gangue minerals are pyrite, quartz, and hematite. In the limestone replacement bodies, chalcopyrite and bornite are the chief ore minerals.

Jan 1, 1968

By W. F. Boericke

INTRODUCTION THE Wisconsin zinc district, or the Upper Mississippi lead. and zinc district as it is also termed, lies in the southwestern corner of Wisconsin, and embraces adjacent portions of Illinois and Iowa. It includes Iowa, Grant, and Lafayette counties in Wisconsin, and Jo Davies county in Illinois. In Iowa, Dubuque formerly produced considerable lead, but there has been little mining there in recent years. The map, Fig. 1, shows the entire district, with roads, railways, streams, and the various towns, or "camps," around Which the mines. are clustered. The hatchwork indicates the areas iii which lead and zinc have been mined. The district is about 60 mi. (96 km.) north and south and about 40 mi. (64 km.) east and west. Not all of the territory is mineral bearing, and there are considerable areas that are believed to be barren. The grouping of the mines is patchy and irregular, though certain broad zones of mineralization extend almost the full width of the district, as from Mineral Point west through Mifflin and Livingston, and from Shullsburg west through New Diggings and Hazel Green. It is worth noting that the best mines of the district have, to date, been found within 10 mi. east or west of the fourth principal meridian line, thus lying within a long, narrow, north-and-south belt extending the length of the district. In a field as large as the Wisconsin, which has only within com-paratively recent time been worked intensively for zinc, the. chances are good for, opening new and important orebodies in parts of the district not yet, or insufficiently, prospected. However, the prospecting has been most successful around, or adjacent to, the old lead diggings of nearly a century ago, and the camps that were well known then are still centers of activity. In their order of importance they are: New Diggings, Benton, Mifflin-Livingston, Galena, Linden, Hazel Green, Shullsburg, and Highland.

Jan 8, 1919

By F. W. Bryan, D. H. Lynch

Introduction This paper is a general description of current central Florida phosphate mining, beneficiation, and product transportation. It is directed and believed to be of interest to engineers not familiar with this industry. Deposit: The phosphate deposits of central Florida are generally located in a five county area which includes Polk, Hillsborough, Hardee, Manatee, and DeSota counties. Geologically, the deposit is of marine origin and is identified as the Bone Valley formation. This formation is Pliocene to Recent in geological age and overlies a Miocene limestone formation known as the Hawthorn. The Bone Valley formation sediments are regionally characterized by equal proportions of apatite, quartz, and clay. The clay is predominantly of the mont-morillonite family. On a local scale, however, the proportions of these three major constituents vary considerably. The phosphate occurs as the apatite mineral (Ca 10F2(PO4)(6) and with the clay and sand, the minable ore is commonly referred to as matrix. This matrix is overlain by unconsolidated overburden of sand and sandy clays, ranging in depth from 10 to 45 ft. The matrix usually occurs in fairly horizontal continuous beds from 3 to 25 ft in thickness. The bedded limestone formation lies directly below the matrix and is generally well defined. The phosphate particles range from 3/4 in. to 200 mesh (Tyler) in size. The phosphate particles coarser than 14 mesh are called pebble phosphate and those less than 14 mesh are termed flotation feed which, when beneficiated, subsequently become concentrates. Through mining and beneficiation, phosphate quality is measured in BPL percent which stands for bone phosphate of lime units. In subsequent chemical manufacturing, the quality is indicated by P205 content. The deposit is economically characterized by various ratios such as tons of product per acre and cubic yards handled per ton of product. Magnesium, iron, and aluminum content are also considered in evaluating ore reserves. These elements are often critical to the chemical fertilizer processes. Presently, an ore body is considered economically minable if it meets the criteria shown in [Table 1]. These, of course, are general guidelines and specific costs and returns on investment must be considered in each case for acquiring reserves. On a new grass-root venture, a 20-30 year life is generally expected with a mineral recovery of 80%. History and Uses Phosphate mining in central Florida began around the turn of the century. However, in the early days, only pebble phosphate was produced until about 1930 when technology was available to beneficiate the -14 + 150 mesh particles. The -150 or -200 mesh material was discarded as it is today. The basic processes for beneficiation are washing, scrubbing, desliming, sizing, and flotation. These basic unit processes are essentially the same today although many improvements have been developed since the early days. Phosphate is used primarily in the production of high analysis fertilizer chemicals, typical of which are triple superphosphate, monoammonium phosphate (MAP), and diammonium phosphate (DAP). Phosphate is also used in the production of food preservatives, dyes for cloths, vitamin and mineral capsules, steel hardeners, gasoline and oil additives, toothpaste, shaving creams and soaps, bone china dishes, plastics, optical glass, photographic films, light filaments, water softeners, insecticides, soft drinks, road fill, and livestock feed supplements. Florida produces over 80% of the nation&apos;s marketable phosphate rock and one-third of the world production, according to the US Bureau of Mines. This amounted to approximately 35 million tons in 1975. Exports of Florida phosphate rock were to such countries as Canada, Japan, West Germany, Italy, and India, with Canada and Japan being the major users. Almost 95 o of all outbound cargo shipped through the port of Tampa is phosphate rock or related products. Beneficiation Following is a description of Agrico&apos;s new Fort Green beneficiation plant which is typical of the newer large capacity plants being built in the field. Agrico&apos;s Fort Green mine was completed in 1975 and is located in the southwest corner of Polk County and is directly adjacent to Manatee, Hillsborough, and Hardee Counties. With some minor differences, Fort Green is typical of a modern central Florida plant. The rated capacity is 3,000,000 plus tons of product per year and this varies according to the richness of the ore being handled. A simplified flowsheet is presented in [Figs.1 and 2]. This plant is served by three draglines of the 40-cu-yd class. The phosphate beneficiation is usually divided into three major functional steps: (1) washing and screening to produce a pebble product and flotation feed, (2) feed preparation and (3) flotation to produce concentrates. The typical plant is similarly divided into these three functional areas. Washer: Briefly, the slurried matrix is pumped from two draglines simultaneously at a combined rate of about 20,000 gpm at 2000 tph (solids) to rotary trommel screens sized to make a 7/8-in. separation. ([See Fig. 1]-) The trommel oversize is sent to hammermills where it is crushed and returned to the trommel screens, or pumped to tailings if minor impurities (Fe203, A1203, MgO) are too high. The trommel undersize is pumped to 14 mesh stationary (static) flat screens. The flat screen over¬size is subjected to three stages of 14 mesh vibrating screening and two stages of log washing in order to produce a final pebble product. The pebble product (+ 14 mesh material) is conveyed by belt conveyor to a large on-ground storage pile. Pebble product is reclaimed through a tunnel and loading system below

Jan 1, 1980

By Frank Firmstone

The indicator cards shown herewith were taken by the writer in June, 1877, from the water-pressure blowing engine of the Longdale Iron Co., at Lucy Selina Furnace, Longdale, Virginia. A description of&apos; this engine with figures, and some indicator cards, was published by Washington Jones, Esq., Superintendent of the I. P. Morris Co.,* in the Journal of the Franklin Institute for May, 1877, to which those desiring a full account are referred, but for convenience the principal dimensions, etc., are given below. The machine consists of a pair of horizontal direct-acting blowing engines, connected at right angles to a common fly-wheel shaft. The blowing cylinders are 4 ft. diameter by 5 ft. stroke; the water cylinders were 18 in. diameter by 5 ft. stroke as built. Both water and blowing cylinders are double acting. The water valves are balanced piston valves, 18 in. diameter, moved directly by eccentrics on the fly-wheel- shaft. Great care was taken to have the areas of the ports and passages at least equal to the area of the working piston. The engine is set about 14 ft. above the tail-race, and the

Jan 1, 1879

By Albert Sauveur

Jan 1, 1924

By Albert Sauveur

Jan 1, 1924

By Thomas L. Kesler

I all of the 14 million tons of kaolin produced in Georgia through 1949 had been mined from a single deposit 20 ft thick, it would represent a mined-out area of less than 1 sq mile. This measure of depletion is in such strong contrast with the large size of the area shown in Fig. 1, from which most of the output has come, that there has developed an optimistic outlook concerning future supplies of kaolin equal in grade to that already mined. Dozens of mines are widely but not evenly distributed within this area, which consists mostly of parts of Twiggs, Wilkinson, and Washington counties. There are scarcely half a dozen kaolin mines elsewhere in the state that have been appreciably productive, although the areas in which they occur may have good possibilities. Most of the efforts to find new deposits, therefore, will be confined to the area shown in Fig. 1, for it is here that the industry has established its facilities, and prospecting is encouraged by relatively numerous outcrops and opened deposits of kaolin. The Ocmulgee and Oconee rivers drain the area. They and their main tributaries have flat, swampy floodplains covered with alluvium and for the most part thickly wooded. The divides between these streams are intricately dissected by the minor tributaries, which are spring-fed in steep-walled, cirque-like heads. Gullying and under-cutting are active along the streams but are partly controlled by unusually dense vegetation. The mean altitude is about 350 ft above sea level, and locally the relief ranges up to 200 ft. The area is near the inner margin of the Coastal Plain, and is underlain by Cretaceous and Tertiary formations. Its general location is shown in black in Fig. 1. The division between the Coastal Plain and the Piedmont plateau is actually a very sinuous line, the fall line, marking the extent to which erosion has stripped the Coastal Plain sediments from the southeastward-sloping surface of the crystalline rocks of the Piedmont. Cretaceous Host Formation The kaolin deposits, which are described in the succeeding section, occur sporadically in lenslike bodies in a thick series of poorly sorted clayey sands constituting the lowermost of the Upper Cretaceous formations, the Tuscaloosa. The basis for this correlation has been reviewed by Cooke.1 The same formation has been termed the Potomac group by Ladd2 and the Middendorf formation by Smith&apos; in reports on the kaolin deposits. In another report, Veatch4 called the formation the Tuscaloosa but correlated it with the Lower Cretaceous. The Tuscaloosa in this area consists of fine to very coarse sands, commonly cross-bedded, which contain widely different proportions of white, pink, and yellow kaolin and considerable white mica. A few of the coarser beds contain quartz grains up to 3 in. in length, with bodies of pure white kaolin of equal size that appear to have been formed by the weathering of feldspar grains in place. In the kaolin-producing area, gravel and cobbles occur mainly at the base of the formation. Fig. 2 shows the relations of the Tuscaloosa and its kaolin deposits to the adjacent formations. Its base, on the eroded surface of the crystalline rocks, dips southeastward 50 to 60 ft to the mile, according to LaMoreaux.5 The upper surface of the Tuscaloosa is also an unconformity,

Jan 1, 1952

By Albert F. J. Bordeaux

INTRODUCTION. THE following general survey of the character and present condition of the silver-mines of Mexico, though not offered as a detailed treatise, has been prepared with care, is believed to he generally up-to-date, and is offered as a summary which may be found useful by mining engineers. Mexico has ranked for several centuries first among the silver-producing countries. It is now second as copper-producer, and seventh as gold-producer, with a fast-increasing output every year. The total amount of capital invested in its mining- and smelting-works is more than $250,000,000, while the yearly metallic production is $160,000,000. There are more than 20,000 recorded mining properties. The silver-mines of Mexico represent deposits of three principal classes: (1) veins and stock-works in eruptive rocks; (2) fissure-veins crossing the crystalline schists, granite, diorite, etc. ; and (3) veins and replacement-deposits in limestone. The true fissure-veins in some districts contain (in value) more gold than silver. In other deposits, the silver is decreasing in depth, leaving galena and zinc-blende as the principal ores.

Jan 9, 1908

By M. L. Requa

This paper is abstracted from the report of the Appraisement Committee of the Independent Oil Producers&apos; Agency, of which the writer was Chairman. The other members of the committee were M. V. McQuigg and R. S. Haseltine. To Thomas Cox, engineer in charge of the investigation, and to his efficient staff of assistants, is due the credit for the detail work necessary in carrying out the plan of the Committee. It treats only of the valuation of the lands, wells, and piping, without going into details of equipment and other features. It was recognized, early in the operation, that the value of oil lands was the value of oil ,to be extracted and marketed, less the costs attendant thereon. Referring this back to the costs in cents per barrel, it became obvious that surface improvements, absolutely necessary in the production of oil, from wells then drilled, had no separate and independent value aside from the value of the land, but that any excess equipment, not necessary for the production of oil from present wells, such as drilling tools, well casing, etc., should be given a present condition value. In valuing the properties of the Independent Oil Producers&apos; Agency, the Committee has considered the following facts: 1. That from each property there will ultimately be produced a certain total quantity of oil. 2. That in the production of that oil a certain total quantity of money will be expended. 3. That a certain total amount of money will be received from the oil. 4. That the total net receipts will be the total gross receipts less the cost of development and production. 5. That the present value of the net receipts must be such an amount that when invested by a purchaser it will be returned with 8 per cent, interest additional during the life of the property. The initial procedure consisted in making a general reconnaissance of the entire district in which the property was located and determining the lithological and structural conditions underlying the area. The data obtained from each individual tract comprised the logs of all the wells

Jan 1, 1918

By Sherwin F. Kelly

THE geophysical scene shifts and alters, the emphasis changes, and new possibilities loom, but the tendency is always towards widening the field and deepening the analytical penetration. Seismic methods have had their heyday, the torsion balance is being displaced by the gravimeter, electrical methods are showing deeper penetration, soil analysis is the newest tool, and gamma-ray logging appears on the horizon. One of the striking features of re- cent geophysical work in the oil fields has been the marked decrease in the number of seismic crews employed. Although the percentage of company crews is believed to have increased appreciably. the sum total has fallen sharply, as shown by the figures for the Gulf Coast area. About two years ago probably over 100 seismic parties were operating there, whereas now there are only about 35. This decrease may be partly due to the low prices of petroleum with a consequent reluctance to spend money to increase crude-oil re- serves but more probably to the fact that reflection and refraction shooting have been carried on so extensively that they have been applied to a large pro- portion of the areas in which they may reasonably be expected to succeed. Some of the earlier enthusiasm, particularly over reflection prospecting, may have erred on the side of over- optimism; some of the present curtailment may be due to over pessimism; but in the opinion of various observers seismic work at the present rate seems to be at it- optimum. It nevertheless remains pre-eminent as a technique for detailing structures in areas where good reflections can be obtained and is the only method that will give accurate depth to definite beds. Results may be poor in certain areas but many regions still remain wherein it can be applied, so that plenty of structural mapping remains to be done by the reflection seismic method.

Jan 1, 1940

By Thomas L. Kesler

IF all of the 14 million tons of kaolin produced in Georgia through 1949 had been mined from a single deposit 20 ft thick, it would represent a mined-out area of less than 1 sq mile. This measure of depletion is in such strong contrast with the large size of the area shown in Fig. 1, from which most of the output has come, that there has developed an optimistic outlook concerning future supplies of kaolin equal in grade to that already mined. Dozens of mines are widely but not evenly distributed within this area, which consists mostly of parts of Twiggs, Wilkinson, and Washington counties. There are scarcely half a dozen kaolin mines elsewhere in the state that have been appreciably productive, although the areas in which they occur may have good possibilities. Most of the efforts to find new deposits, therefore, will be confined to the area shown in Fig. 1, for it is here that the industry has established its facilities, and prospecting is encouraged by relatively numerous outcrops and opened deposits of kaolin.

Jan 10, 1951

In uranium metallurgy, the main purpose is to obtain a product containing 80-85% U308 (yellowcake) from ores whose average grade is a mere 0.21% U30& Essentially, the task of extraction and concentration involves dissolving the ore&apos;s U308 values, followed by purification and concentration of the uranium-rich solution (using such operations as filtration, clarification, and ion-exchange), and then selectively precipitating and isolating U308. Leaching is First Step In yellowcake production mills, the first chemical change occurs by leaching the ore with either sulfuric acid-as done by Anaconda and Kerr-McGee-or with an alkaline solution of, say, sodium carbonate, as done by United Nuclear-Homestake Partners. The choice of either acid or alkaline leaching is not an arbitrary one: it depends on the chemical and physical characteristics of a particular ore. That is, on the presence of clays, organic compounds (usually of carbonaceous origin), and soluble impurities, as well as on the ore&apos;s wetness and grindability.

Jan 8, 1974

By W. B. Mather

GEOLOGICAL studies have revealed the occurrence of hundreds of pegmatite dikes in north- east Brazil, Fig. 1, in the three states of Rio Grande do Norte, Paraiba, and Ceara. Heretofore data have not been available on the possible production of lithium minerals from these areas, and in March, April, and May 1953 the author undertook a reconnaissance survey covering a cross-section of the pegmatites. Sixty-one pegmatites were examined. The pegmatites of Rio Grande do Norte and Paraiba are located in an arid region (Seratao), and except in the most southerly portion there is a mini- mum of vegetation and overburden. The region is easily prospected and relatively accessible by jeep or truck. The pegmatites examined in Ceara are in an area of lush vegetation along the flanks of the Jaqueribe River valley. It is therefore more difficult to prospect, and the dirt roads, as a means of access, leave much to be desired. For all practical purposes rail transportation, except in Ceara, is not available. The rocks of the area1-4 are composed of Pre-Cambrian schist, gneiss, quartzite, and marbles. They have been intruded by granites, monzonites, and diorites and cut by quartz veins and pegmatites.

Jan 9, 1954

The new, internationally-owned Savage River Mines iron ore mining, concentrating and pelletizing project, built and operated by Pickands Mather & Co. International, was dedicated March 6 at Port Latta, Tasmania, Australia. Construction of the $79 million project began in 1965 and involved an open pit mine and concentrating plant plus a complete town for about 350 employees at Savage River; a 53-mile pipeline to transport the concentrates; a pelletizing plant and shipping facilities at Port Latta, which is on Bass Strait separating Tasmania from the Australian mainland. The project has a rated capacity of 2.25 million Ltpy of high-grade magnetite pellets, which will be sold to five Japanese steel companies under 20-year contracts. The open pit mine is located in the central portion of the Savage River deposits. Mining equipment, capable of moving 10 million tpy of ore and overburden, consists of four 6-cu yd electric shovels and 12 50-ton trucks. The concentrating plant, with a design capacity of 5 million tpy of ore, will use magnetic separators to upgrade the ore, which averages 38% iron, to a concentrate averaging 67% iron.

Jan 4, 1968

By Ira B. Joralemon

INDIVIDUALS and small companies have discovered and brought into production the mining districts of the United States. Hardly an exception comes to mind, save for the disseminated copper properties and the great iron mines. In spite of this fine record that has made possible the industrial greatness of the country, mining by small companies and by individuals has become a vanishing phenomenon. In Nevada, the lair of rugged individualism, there are fewer operating mines and fewer miners than at any time since the 1860&apos;s. The situation in other states is nearly as desperate.

Jan 8, 1950

By R. P. Fischer

The Colorado Plateau region has been the principal domestic source of uranium, vanadium, and radium. The value of these commodities produced from the region through 1964 slightly exceeds $2 billion. Most of the deposits occur in streamlaid lenses of sandstone in the Chinle and Morrison Formations. The ore minerals below the zone of oxidation are low-valent oxides and silicates of uranium and vanadium; all of these, except the quite stable vanadium silicates, oxidize readily to a variety of high-valent uranium and vanadium minerals. The ore minerals partly replace fossil wood but mainly impregnate sandstone, typically forming tabular ore bodies that are nearly concordant to the bedding of the host rock. The deposits range in size from those containing only a few tons of ore to those containing more than 1 million tons. Stratigraphic, lithologic, and sedimentary structural factors obviously influenced the localization of these deposits, but igneous activity, hydrothermal mineralization, and tectonic structures show no similarly consistent influence on localization. The deposits are epigenetic, but the source of the ore metals, the nature of the ore-bearing solutions, and the time of ore emplacement are uncertain. A few uranium deposits in the region are dominantly discordant to bedding and occur in collapsed breccia pipes or along linear fractures. Their origins are also uncertain.

Jan 1, 1968