Search Documents

By Elmer R. Kaiser

COMBUSTION of coal and transfer of heat from flames and gases to boiler surfaces continue to be of great interest to engineers here and abroad. Numerous investigations have been in progress to improve furnace and boiler performance and economy. The importance of better understanding of the processes and opportunities for improvement is apparent when it is remembered that heat from at least 500 million tons of coal a year the world over is being transferred to boiler water at efficiencies ranging mostly between 50 and 90 pct. Even slight gains in efficiency, economy, and labor saving become very significant when multiplied by the enormous quantity of fuel consumed. Also the competitive position of the large coal, oil, and gas industries in satisfying the fuel consumers is greatly affected by the achievements made through technical progress with each fuel. This paper is part of a continuing activity of Bituminous Coal Research, Inc., to extend the knowledge of coal utilization for steam generation and to seek promising directions for future research and development in cooperation with others. Particularly in the latter regard, numerous interviews were held during the last three years to seek the experience and advice of boiler and combustion-equipment manufacturers, electric-utility executives, and fuel engineers. A wealth of published information was also reviewed, which together with the interviews pointed to the advisability of further work on ash and sulphur control. For the present purpose a number of factors important to efficient heat liberation and recovery have been grouped as follows: 1—combustion, temperatures, and rates of heat liberation; 2—radiation, convection, and furnace and boiler configuration; 3—sponge ash, slag, and hard-bonded deposits; 4— low-temperature deposits and corrosion (cooling flue gas below dew point and air-pollution control); 5—the limitations of coal cleaning and boiler size and cost as related to fuel characteristics; 6—future possibilities and conclusions. The development of combustion apparatus for power boilers is progressing at a lively pace. There has been no letup in improvements in design of pulverized-coal-fired boilers, and there is a strong trend at present toward improving dry-bottom units. Spreader stokers with overfire jets and dust collectors as standard equipment are gaining favor. Less than 10 years in commercial use, cyclone burners are going into numerous installations here' and abroad.' Underfeed and traveling-grate stokers have long since been developed for heavy-duty operation, yet new developments in overfire jets and humidification of air blast have improved their performance. A water-cooled vibrating-grate stoker of German origin is being introduced into the United States and Canada." The primary objectives of an ideal coal combustion device are: capacity to burn the variety and sizes of coals likely to be economically available during the life of the unit; capacity to burn the coals automatically for a wide load range and rapid load fluctuations and to burn the coals completely to CO2, H2O, and SO2, which means without smoke and cinders, or carbon in the refuse; capacity to control and discharge all the ash in final granular form without ash adhesion to walls or tubes, and without flue dust; minimum furnace volume; minimum labor and maintenance; low initial and operating cost. Regardless of the method of burning, the gaseous products of coal combustion are N2, CO2, O2, H20, and SO?. By way of illustration, the coal analyses in Table I is assumed from an installation described by E. McCarthy.' When coal is burned with 20 pct excess air (theoretical air, 9.23 lb per lb of coal), the quantities of combustion gas shown in Table II are produced. In addition, the gases carry particles of fly ash, unconsumed cinders, soot particles, and small but significant amounts of vaporized oxides and sulphates of sodium, potassium, lithium, phosghorous, iron, and other metals. In recent years, germanium, one of the rare metals found in coal, has been shown to oxidize and vaporize at combustion temperatures and to be concentrated by reconden-sation at lower temperatures." Pulverized coal and cyclone flames" have peak temperatures of 3000' to 3500°F. Temperatures in fuel beds of large underfeed stokers reach maxima of 3000°F, sufficient to fuse almost any ash and to volatilize some of it. These peak temperatures are above the optimum necessary for rapid combustion, but they hasten heat transfer for ignition as well as boiler heat absorption. Furnace and gas temperatures increase with combustion air preheat. Low excess air has the same effect. Fine coal pulverization and highly turbulent combustion shorten the distance for fuel burnout, increase flame temperature, and speed up heat transfer. Rates of combustion of pulverized coal exceeding 200,000 Btu per cu ft per hr have been demonstrated in atmospheric gas-turbine combusters,

Jan 1, 1955

By H. D. Attra

The effects of phase behavior on reservoir economics is a function of both fluid composition and flow properties of the reservoir rock. In some operations such as gas injection into volatile crude-oil resertoirs, the stock-tank recovery derived from vaporization of the reservoir oil by the displacing gas can approach the recovery derived from the displacement mechanism. In other cases of gas-cycling reservoirs, the dry injected gas can effectively vaporize a retrograde liquid phase, allowing a substantial reduction in cycling pressure with no appreciable loss in recoverable liquids. Because of these effects, it is essential that phase behavior be considered in developing the economics of any secondary recovery program in which gas is the injected fluid. The inclusion of phase behavior in conventional calculation procedures has been retarded because of the complexity of the calculation and the large volume of laboratory data required. However, by applying high-speed computers and new laboratory techniques, the phase-behavior displacement calculation has been developed to economically include this basic fundamental of gas displacement. The calculation is performed by reducing the reservoir to a series of one-dimensional segments. Phase changes, saturation distributions and changing fluid properties are evaluated for each segment as a function of time. The relative volumes of equilibrium liquid and gas displaced from each segment are determined by a trial-and-error procedure to meet the requirements of phase equilibrium and two-phase flow. The produced fluids are flashed through conditions of surface separation approximating those in the field to obtain actual values for stock-tank liquid recovery and producing gas-oil ratios. Based on the results of successful field studies, the technique appears to have application to reservoirs producing under a nonmiscible gas-displacement mechanism and should substantially increase the reliability of this type of analysis when phase behavior is an important factor. Predicting reservoir performance under gas-injection operations involves three basic principles of reservoir engineering. First, a material balance exists between the displacing gas and the displaced reservoir fluid. Second, the oil and gas flow in relationship with the two-phase flow property of the reservoir rock; and third, phase equilibrium exists between the displacing gas and the native reservoir fluid. To illustrate these three principles, consider the one-dimensional reservoir shown in Fig. 1. The reservoir is divided into a series of segments representing a one-dimensional cross section between an injection area and a producing area. So represents the oil saturation, Cw represents the connate-water saturation and Sg represents the displacing gas saturation. The gas is moving into Segment 1 and the reservoir oil is being produced out of Segment N. Consider the case when gas has just moved into Segment 1 and the displacing gas-oil contact is at position a-a The volume of oil pushed out of Segment 1 is a function only of mobility and the two-phase flow properties of the reservoir rock, that is, Kg/Ko and µo/µg. Behind the front if the injected gas is foreign to the reservoir oil (a nonequilibrium gas), there will either be vaporization of the oil into the gas or condensation of the gas into the oil. In either case the net result is a mass transfer and a re-distribution of composition and liquid and gas saturation. If the displacement is at constant pressure and is continued, the gas moves into new segments, proceeding succesively into Segment 2, 3, etc. The total volume of oil produced from the reservoir

By HARRINCTON EMERSON

UNEMPLOYMENT is the most ominous shadow ahead of the industrial nations today. Only two great industrial countries are free from unemployment, France and the Soviet Commonwealth. In France the social unit is the family, not the individual. This has saved France. In the Soviet Commonwealth, development is proceeding so rapidly from agricultural to industrial that there is still a dearth of muscle workers in the non-agricultural enterprises. In the other industrial countries unemployment results both from acute temporary recession in industrial activities and from the rapidly increasing substitution of the machine for the man. Temporary recessions can be mitigated, alleviated by makeshifts, often ill considered. Secular recessions due to a fundamental change in the way of accomplishing physical, chemical results cannot be cured by any makeshift. There must be a period of transition. There is therefore before us the three- fold problem, immediate, prosimate and ultimate.

Jan 1, 1930

By R. L. Perrine

This paper presents results obtained by consider ation of unstable miscible displacement within a porous medium as a quasi-turbulent displacement process, that is, a process characterized by fluctuations around a simpler, mean flow behavior. The instability usually results from the miscible displacing fluid having a viscosity lower than that of the displaced fluid. Such instability is evidenced in suitable experiments by the presence of viscous fingering. A unified theoretical relationship applicable to both stable and unstable displacement is derived. Parameters in the theory are obtained by empirical means. Although the theory describes an idealized conceptual model, agreement with experiment is quite reasonable up to moderately adverse viscosity ratios, such as 17:1. INTRODUCTION Many experimental studies of miscible displacement in porous media have been conducted with prediction of reservoir displacement efficiency as the ultimate objective. Most such studies have utilized lower displacing than displaced fluid viscosity, scaled to potential reservoir fluid pairs. Theoretical approaches have been largely limited to unit viscosity ratios, however, in spite of the necessity for an understanding of the mechanism of the unstable, adverse viscosity ratio displacement process. An obvious reason is the difficulty of describing in mathematical form the viscous fingering characteristic of these conditions. Observation of experiments conducted with dyed fluids in transparent systems suggests an analogy between unstable miscible displacement and turbulent flow in a pipe. In both cases there are fluctuations around a simpler, mean flow behavior. An important difference is that flow behavior of interest in the porous medium is entirely transient, contained within a transition zone between displacing and displaced fluids. Transient behavior complicates description in that coefficients in the equations become variables rather than constants. In the study reported here, the analogy with turbulent flow has been used in treating unstable miscible displacement as a quasi-turbulent displacement process. The purpose has been to derive, even if restricted to an idealized conceptual model, a unified theoretical relationship applicable to both stable and unstable displacement. A relationship meeting these specifications up to moderately adverse viscosity ratios, such as 17:1, is presented. One fluctuation parameter in the theory and dispersion coefficients are obtained by empirical means. The idealized theory is compared with experimental results. UNSTABLE MISCIBLE DISPLACEMENT AS QUASI-TURBULENT DARCY FLOW The miscible displacement of one fluid by another within a porous medium is considered in this study. Flow conditions are such that Darcy's law is applicable. It is further assumed that, by the stability criterion proposed by perrine,1 initial flow conditions lie well within the regime of instability. Thus substantial viscous fingering is assured. We wish to show how this flow regime can be represented as quasi-turbulent. That is, the Reynolds number for the established flow conditions is below that for inertial or turbulent flow within a porous medium, and lies within the regime for which Darcy's law is valid. Yet flow behavior can be described as the combination of some relatively simple average result, and characteristic fluctuations that are superimposed on the simpler behavior. Stated another way, flow behavior includes the movement of layers of fluids with different velocities past or over one another. Such descriptions are characteristic of turbulent pipe flow. The fluctuations in the present case are a direct consequence of the local viscous fingering which accompanies the unstable displacement process. Should displacement become stable, fluctuations would die out. It is of particular importance to note that fluctuations such as these can interact in a way that contributes to material transport by the basic flow. The basic transport equations required for engineering calculations must be modified to reflect this fact.

By F. A. J. Fitzgerald

In any kind of furnace the question of preventing the loss of heat is important, for no matter how the heat is obtained it costs something; and consequently, other things equal, that furnace is most desirable which uses the greatest percentage of the total heat generated for the particular object in view. In the furnace which uses electricity for the generation of heat the importance of preventing losses of heat is very much greater than in any other. To generate 1,000 kg-cal. requires an expenditure of 1.16 kw-hr., and consequently the cost per calorie is always expensive when electricity is used for heating. In heating any material in a furnace a general rule is that the generation of heat should be as rapid as possible. In any given furnace the heat-losses may be expressed as so many watts, and, therefore, the longer it takes to heat the furnace-charge the greater the losses will be. Suppose that a furnace contains a charge to be heated to 1,500°C. and that the average loss of heat is at the rate of 100 kw., then if the process of heating the charge takes 1 hr. the losses will amount to 100 kw-hr.; but if by using a more rapid generation of energy the charge can be heated in 30 min. the losses will amount to 50 kv-hr. An example from experiments on a certain process may be given to illustrate this point. The problem was simply to heat a furnace-charge to a certain temperature, and experiments were made to determine the effect of increasing the rate of generation of energy and comparing the kilowatt-hours required to heat a given charge. Here are typical results : Rate of Generation Energy Per Kg. of Energy. of product 88 kw. 1.7 kw-hr. 93 kw. 1.6 kw-hr.

Jan 1, 1913

By James Boyd

Scientists and engineers must concern themselves not only with technical problems, but with the socio-economic difficulties of our scciety. The author states that raw materials are basic to the economic process and that mineral raw materials occur naturally in nearly limitless quantities. He feels that the economic pocess will provide sufficient raw materials for man's needs, and discusses in some detail the world economic environment. As our society grows in complexity, it becomes more urgently incumbent upon scientists and engineers to bring their experiences to bear on the solution, not only of technical problems, but also on socio-economic difficulties. It is to this field that I have directed a large part of my energies. RAW MATERIALS BASIC TO THE ECONOMIC PROCESS There are certain premises, frequently overlooked, which bear emphasis. As economics concerns the production, distribution, and consumption of goods, so our whole society is based on raw materials. Without the basic extractive industries of agriculture and mining, there would be no economic problems with which to deal. This principle has been expressed as "All productivity is based on three factors: 1) natural resources, whose form, place, and condition are changed by the expenditure of 2) human energy (both muscular and mental), with the aid of 3) tools.77* It seems strange that such an obvious statement needs to be made. It is forgotten by all of us, however, at one time or another when we get involved in the complicated theories of economics dealing with the financial and fiscal policies of the various governments, in the financing of enterprises, in marketing, and in labor relations. Unless decisions in all of these fields are made with this, and the rest of the "Ten Pillars of Economic Wisdom," consciously in mind, the resultant policies are doomed to eventual failure, whether these are policies of individuals, companies, or governments. The economic process is basic to society. But economics and the social aspects of humanity are inevitably intertwined. If human needs are not provided for within the basic economic structure, conflicts arise to disrupt the most carefully laid social plans. Similarly, it is the failure of society to cope with basic economic prerequisites that leads to discord within the body politic and thus to eventual economic disaster. We who are engaged in the various aspects of the mineral industry, therefore, have a large part to play in society's future development. MINERAL RAW MATERIALS OCCUR NATURALLY IN NEARLY LIMITLESS QUANTITIES Throughout my career in and out of government, I have formed my decisions on two principles: 1) Fundamentally, all mineral raw materials exist within the earth's crust in quantities greatly exceeding man's needs; 2) Any problems of supply of these materials are primarily economic in nature. With respect to my first assumption, analyses by geochemists enable them to estimate the quantities in which each of the known elements exist in the earth's crust. One of the most cautious and famous suggests that the average copper content of the lithosphere to a depth of ten miles is about 55 ppm. If this is valid, then the lithosphere contains about 1.4 quadrillion (1.4 x 10 ") tons of copper metal — an unimaginable quantity. This is 8,500,000-fold that which has been consumed by man in his existence. To illustrate further, consider that the deepest copper mine in history went to about 9000 ft below the surface; the present copper mines of the world now average less than 1500 ft in depth. We can assume that in most continental land areas of the world it is technically feasible to mine to a depth of at least one mile. The land areas of the world to an average depth of one mile, then, contain 343 billion tons (343 x 10') of copper metal, or 2000 times that which has been extracted to date. I don't believe man will ever expend his energies to extract copper from rocks which contain only a few parts per million, but he knows that each element

Jan 1, 1968

By John Birkinbine

(Read at the Philadelphia Meeting, February, 1878.) IN a former paper* attention was directed to the various firms of pumping machines employed for permanent work in mining and metallurgical processes. The following is simply a collection of memoranda of work done of a temporary character, and is presented by way of comparison with other work of similar nature. In close proximity to the charcoal furnace at Pine Grove, Cumberland County, Pa., is a large deposit of superior hematite iron ore, which has been worked for a number of years, and from which many thousand tons of ore have been taken by open pit workings. In July, 1874, the furnace was blown out and operations at the bank suspended, the machinery for draining being removed except a plunger pump, 18 inches in diameter and 66 inches stroke, operated by a steam-engine by means of rods. The pit was allowed to fill with water, and no steps towards its reclamation were taken until November, 1877. At that time the pit was a pond of water at the base of the mountain, having an area of about four acres and a depth of seventy feet. As the pumps, rods, etc., had been submerged for over three years, and partially buried by the mud washed down from the banks, and as it was determined to change the location of the pump for future operations and drive it by water-power, a temporary pumping apparatus was determined upon for reclaiming the pit and keeping it drained until the permanent arrangements could be completed. By opening an old adit about 10 feet of the water was removed, and the area decreased to three acres. The inflow of springs was found to be 250 gallons per minute, and the amount of water contained in the pit was computed to be 45,000,000 gallons. As the inflow would undoubtedly increase while the water sank in the pit, provision was made for removing at least 60,000,000 gallons, at the rate of 1,500,000 to 2,000,000 gallons per day. The company determined to employ a Heald and Cisco centrifugal pump driven by an oscillating engine by means of a belt. Steam was supplied by four plain cylinder boilers, each 36 inches diameter *Transactioiis of the American Institute of Mining Engineers, vol. p. 455.

Jan 1, 1878

By Robert H. Richards

(Read at the Wilkes-Barre Meeting, May. 1877.) THE Institute of Mining Engineers has shown so much interest in the educational problem of profitably combining theory and practice, that it seems especially appropriate to lay before its members the methods and aims of the mining laboratory of which I have charge, and in which one form of combination of hand with head work is now being tried. If anything may be contributed toward the solution of this problem by the discussion which follows, my purpose will be attained. Whether it was wise or not to establish a mining school so far from the principal mining centres, does not now enter into the question. Given, a mining school already begun, how shall it be made most efficient in developing engineers who are trained to think for themselves as well as versed in the works of others? This is the ques¬tion with which we have had to deal. In considering the bearing of this laboratory work upon the students' preparation, it will be convenient to take it up under five different heads 1. The methods and aims of the laboratory. 2. The advantage to students of having a part, at least, of their practical work in the curriculum of their school. 3. The advantage to be derived by mines and works. 4. Degree of accuracy which may be attained in working ores on a small scale. 5. Results of work in the laboratory. 1. The Methods and Aims of the Laboratory.-During the May meeting of 1873, held in Boston, I had the privilege of reading before you a paper stating the plans and aims of this laboratory. Since that time we have been constantly following out those plans, and are more than ever convinced that we are working in the right direction. We do not feel that the time we have spent has been in any sense thrown away. Perhaps the aims of the laboratory can be most clearly shown by illustration. Many young engineers leave school thinking that they know everything. They go to the works, and expect to teach the superintendent something and the men a good deal, regardless of the fact that it is this spirit that has prejudiced workmen against schoolmen. They are often more trouble than they

Jan 1, 1878

By R. C. Ferguson, Harlowe Hardinge

Oscar Johnson—In my opinion, the effect of mill speeds on grinding costs must be studied along with capital investment and dollars gathered together as profits. Comparing the entire groups of operators with those who have had the opportunity to make slow-speed mill studies, I think you will find the latter small in numbers. Most managers want the equipment worked to its maximum output. There are, however, some installations where plant and mill sizes are such that they can do the job with reduction of mill barrel speeds. The past and the present installations of the industry are laid out to get the most capacity for the least capital outlay. This is the case even with the plants of Chile Exploration, International Nickel, Morocco, and Anaconda, now under construction or being changed. The industry recognizes that most all equipment it buys today is good and can be depended upon for efficient performance. Under this scheme of things, I am doubtful that slow-speed ball mill operation will be generally applicable. With reference to the U. S. Bureau of Mines laboratory tests, I think table II could have been omitted. It is inconclusive as to maximum efficiency for the low-pulp level mill on hard ore. There should be no question about this point. However, data on mill speeds can be found to substantiate various theories as well as refute them. Gow, Guggenheim, Campbell and Coghill, in their paper on Ball Milling,' believe their 2 x 2 ft laboratory mill reflects results that can be expected from large mills. If so, then referring to their table 11, they state, "The conclusion to be drawn from this second series is that high speed, not exceeding 72 pct of the critical, favors capacity, as before, but that with proper conditions of operation high speeds may give as good efficiency values as low speeds. In this case the efficiency values are nearly constant. A horizontal curve would indicate that the amount of grinding was directly proportional to the power expended, and these tests suggest that such a coildition can be made to exist in commercial operations." Table II (From Paper by Gow et a1)2 Speed. Pot Critical 32 42 52 62 72 82 Capacity: Surface tons per hr (65- mesh) 266 42.1 54.4 65.9 74.3 74.1 Surface tons per hr (200- mesh) 56.1 87.4 112.7 137.1 154.2 153.0 Efficiency: Surface tons per net hp hr (65-mesh) 35.7 36.3 36.3 35.4 34.3 32.3 Surface tons per net hp hr (200-mesh) 75.3 75.3 75.1 73.7 71.0 66.0 Ore in mill, 1.b. 98 100 100 113 122 165 The field performance data, table 111, represents much effort in its collection and preparation. But, one must realize that there are many variables that effect the efficiency of grinding mill operation, and too much must not be assumed as to the effect of some specific change. Possibly with changes in mill speed, the results might be more consistent by also a change in ball rationing, type of ball, volume of ball charge,. p.ulp level and amount of pulp in the mill, pulp consisting, design of liner, circulating load, etc. Also, changes in ore character must be reckoned with when evaluating grinding performance. At present the Climax Molybdenum Corp. is running at much reduced capacity. Mr. James Duggan informs me that at mill speeds of 17 rpm, they save a $0.025 per ton on liners and $0.025 per ton in power, but, if the demand for molybdenum increased, he would go back to higher speed to obtain maximum tonnage, as the values from the increased tonnage would far more than offset the one half saving at the slower speed. The Jnspiration ran a six months' test between mills running 21 rpm and 23.5 rpm. The slower mills ground 10 pct less ore with a slight saving per ton, but when the reduced plant tonnage was checked back into the actual cost figures of concentration, the high-speed mills with their greater tonnage showed considerable advantage. To be convinced of possible practical results from the predictions in the conclusions, I think we would have to rely on the analysis of expert cost accountants to furnish the necessary proof figures. Hardinge and Ferguson are to be commended for the work in preparing this paper. I am convinced that our Massco engineers should go into higher speeds with our equipment. Harlowe Hardinge (authors' reply)—For one, I heartily agree with Mr. Johnson's opening statement that the effect of mill speeds on grinding costs must be studied along with capital investment and dollars gathered together as profits. It was on this basis and for this reason the paper was written. Mr. Johnson, on the other hand, takes the position that, on the whole, low speeds are not justified from the economic standpoint, basing his principal reason on the fact that lower mill speeds cut mill capacities and hence reduce the gross income from the product produced. There is no denying this point. It is almost axiomatic. It is for this very reason that the overall advantage of lower mill speeds has been discounted and even overlooked. It was for this reason mainly that the paper was written in the first place. It is one thing to plan an efficient operation at the outset, basing one's figures on the tonnage requirements at the time, and it is quite another to be confronted with the problem of increasing the output of an existing installation at a minimum of capital expenditure. Economic consideration of a new installation is greatly influenced by referring to an old one. Too often, the analyst assumes that if this practice is followed in the new installation, one would not go wrong. It is just here that he may be wrong. Past practice and low capital expenditure are all too frequently given priority over the engineer's analysis of operating costs. When we are able to start fresh, we should give proper weight to other economic factors which do not exist in an old installation. It is these economic factors that make it possible to spend at the outset just a little more money and get it back in a matter of months and effect big savings for years to come. F. C. Bond—This paper is of considerable importance in that it emphasizes a modern trend to operate ball mills at somewhat slower speeds than formerly. We have checked the data in the paper with that obtained

Jan 1, 1951

By Harlowe Hardinge, R. C. Ferguson

Oscar Johnson—In my opinion, the effect of mill speeds on grinding costs must be studied along with capital investment and dollars gathered together as profits. Comparing the entire groups of operators with those who have had the opportunity to make slow-speed mill studies, I think you will find the latter small in numbers. Most managers want the equipment worked to its maximum output. There are, however, some installations where plant and mill sizes are such that they can do the job with reduction of mill barrel speeds. The past and the present installations of the industry are laid out to get the most capacity for the least capital outlay. This is the case even with the plants of Chile Exploration, International Nickel, Morocco, and Anaconda, now under construction or being changed. The industry recognizes that most all equipment it buys today is good and can be depended upon for efficient performance. Under this scheme of things, I am doubtful that slow-speed ball mill operation will be generally applicable. With reference to the U. S. Bureau of Mines laboratory tests, I think table II could have been omitted. It is inconclusive as to maximum efficiency for the low-pulp level mill on hard ore. There should be no question about this point. However, data on mill speeds can be found to substantiate various theories as well as refute them. Gow, Guggenheim, Campbell and Coghill, in their paper on Ball Milling,' believe their 2 x 2 ft laboratory mill reflects results that can be expected from large mills. If so, then referring to their table 11, they state, "The conclusion to be drawn from this second series is that high speed, not exceeding 72 pct of the critical, favors capacity, as before, but that with proper conditions of operation high speeds may give as good efficiency values as low speeds. In this case the efficiency values are nearly constant. A horizontal curve would indicate that the amount of grinding was directly proportional to the power expended, and these tests suggest that such a coildition can be made to exist in commercial operations." Table II (From Paper by Gow et a1)2 Speed. Pot Critical 32 42 52 62 72 82 Capacity: Surface tons per hr (65- mesh) 266 42.1 54.4 65.9 74.3 74.1 Surface tons per hr (200- mesh) 56.1 87.4 112.7 137.1 154.2 153.0 Efficiency: Surface tons per net hp hr (65-mesh) 35.7 36.3 36.3 35.4 34.3 32.3 Surface tons per net hp hr (200-mesh) 75.3 75.3 75.1 73.7 71.0 66.0 Ore in mill, 1.b. 98 100 100 113 122 165 The field performance data, table 111, represents much effort in its collection and preparation. But, one must realize that there are many variables that effect the efficiency of grinding mill operation, and too much must not be assumed as to the effect of some specific change. Possibly with changes in mill speed, the results might be more consistent by also a change in ball rationing, type of ball, volume of ball charge,. p.ulp level and amount of pulp in the mill, pulp consisting, design of liner, circulating load, etc. Also, changes in ore character must be reckoned with when evaluating grinding performance. At present the Climax Molybdenum Corp. is running at much reduced capacity. Mr. James Duggan informs me that at mill speeds of 17 rpm, they save a $0.025 per ton on liners and $0.025 per ton in power, but, if the demand for molybdenum increased, he would go back to higher speed to obtain maximum tonnage, as the values from the increased tonnage would far more than offset the one half saving at the slower speed. The Jnspiration ran a six months' test between mills running 21 rpm and 23.5 rpm. The slower mills ground 10 pct less ore with a slight saving per ton, but when the reduced plant tonnage was checked back into the actual cost figures of concentration, the high-speed mills with their greater tonnage showed considerable advantage. To be convinced of possible practical results from the predictions in the conclusions, I think we would have to rely on the analysis of expert cost accountants to furnish the necessary proof figures. Hardinge and Ferguson are to be commended for the work in preparing this paper. I am convinced that our Massco engineers should go into higher speeds with our equipment. Harlowe Hardinge (authors' reply)—For one, I heartily agree with Mr. Johnson's opening statement that the effect of mill speeds on grinding costs must be studied along with capital investment and dollars gathered together as profits. It was on this basis and for this reason the paper was written. Mr. Johnson, on the other hand, takes the position that, on the whole, low speeds are not justified from the economic standpoint, basing his principal reason on the fact that lower mill speeds cut mill capacities and hence reduce the gross income from the product produced. There is no denying this point. It is almost axiomatic. It is for this very reason that the overall advantage of lower mill speeds has been discounted and even overlooked. It was for this reason mainly that the paper was written in the first place. It is one thing to plan an efficient operation at the outset, basing one's figures on the tonnage requirements at the time, and it is quite another to be confronted with the problem of increasing the output of an existing installation at a minimum of capital expenditure. Economic consideration of a new installation is greatly influenced by referring to an old one. Too often, the analyst assumes that if this practice is followed in the new installation, one would not go wrong. It is just here that he may be wrong. Past practice and low capital expenditure are all too frequently given priority over the engineer's analysis of operating costs. When we are able to start fresh, we should give proper weight to other economic factors which do not exist in an old installation. It is these economic factors that make it possible to spend at the outset just a little more money and get it back in a matter of months and effect big savings for years to come. F. C. Bond—This paper is of considerable importance in that it emphasizes a modern trend to operate ball mills at somewhat slower speeds than formerly. We have checked the data in the paper with that obtained

Jan 1, 1951

By H. A. Schwartz, W. Kenneth Bock

In this paper it is shown that when the tensile strength of a given steel in various states of heat-treatment is plotted against its elongation, a straight line results. The equation of this straight line can be computed with considerable accuracy from its chemical composition. The appropriate equations are given. The logarithm of the slope of the tensile-strength locus is shown to be proportional to the cumulative effect of the total alloy addition and the vosition of the line to be directly proportional to the cumulative effect of the alloy content. It is further pointed out that heat-treatment is more effective than composition in determining yield ratio. The latter enters mainly by its effect on hardenability, which is briefly discussed. Reduction of area and Brinell number are given some incidental attention. The data are applicable only to steels that have been normalized and/or quenched. The steels, if normalized, may or may not have been tempered. If quenched they must have been tempered at or above 4oo°C. (75o°F.). Introduction Cast steels vary in composition and frequently are used in various states of heat-treatment. It is obviously important to be able to predict the compositions that might accompany specific engineering properties by suitable selection of heat-treatments. For cast steels, which are of necessity produced heat by heat in accordance with the particular requirements of the castings to be poured, there has been, happily, much less tendency to standardization than for rolled products, whose destination is not necessarily known when particular ingots are made or rolled. It is of distinct advantage to the steel foundry-men to be able to make steel of given properties, using alloys that can be recovered from scrap, or most conveniently or cheaply bought, rather than a particular formula adopted in the interest of standardization. The heat-treatment appropriate to securing a given result in a given steel is well known to be closely related to composition. For example, molybdenum steels are not much softened by tempering except at rather high temperatures. Highly alloyed steels are "air-hardening," and on cooling in air behave like carbon steels that have been quenched. With these matters, we do not concern ourselves in this paper, although we recognize their importance. The entire picture evidently will be very complex and can be brought within accurate understanding only if our knowledge of test results can be coordinated in terms of general principles.

Jan 1, 1944

By H. A. Schwartz, W. Kenneth Bock

In this paper it is shown that when the tensile strength of a given steel in various states of heat-treatment is plotted against its elongation, a straight line results. The equation of this straight line can be computed with considerable accuracy from its chemical composition. The appropriate equations are given. The logarithm of the slope of the tensile-strength locus is shown to be proportional to the cumulative effect of the total alloy addition and the vosition of the line to be directly proportional to the cumulative effect of the alloy content. It is further pointed out that heat-treatment is more effective than composition in determining yield ratio. The latter enters mainly by its effect on hardenability, which is briefly discussed. Reduction of area and Brinell number are given some incidental attention. The data are applicable only to steels that have been normalized and/or quenched. The steels, if normalized, may or may not have been tempered. If quenched they must have been tempered at or above 4oo°C. (75o°F.). Introduction Cast steels vary in composition and frequently are used in various states of heat-treatment. It is obviously important to be able to predict the compositions that might accompany specific engineering properties by suitable selection of heat-treatments. For cast steels, which are of necessity produced heat by heat in accordance with the particular requirements of the castings to be poured, there has been, happily, much less tendency to standardization than for rolled products, whose destination is not necessarily known when particular ingots are made or rolled. It is of distinct advantage to the steel foundry-men to be able to make steel of given properties, using alloys that can be recovered from scrap, or most conveniently or cheaply bought, rather than a particular formula adopted in the interest of standardization. The heat-treatment appropriate to securing a given result in a given steel is well known to be closely related to composition. For example, molybdenum steels are not much softened by tempering except at rather high temperatures. Highly alloyed steels are "air-hardening," and on cooling in air behave like carbon steels that have been quenched. With these matters, we do not concern ourselves in this paper, although we recognize their importance. The entire picture evidently will be very complex and can be brought within accurate understanding only if our knowledge of test results can be coordinated in terms of general principles.

Jan 1, 1944

By James H. Courtright, Kenyon Richard

TOQUEPALA is a porphyry copper deposit in which mineralization is localized by a large breccia pipe formed in close genetic relation to intrusive rocks. The deposit is in southern Peru, 55 airline miles north of the small city of Tacna and the same distance inland from the port of 110. Quellaveco and Cuajone, geologically similar deposits, lie 12 and 19 miles north of Toquepala. Chuquicamata is 400 miles to the south. The deposit is high on the southwestern slope about 20 miles from the crest of the Cordillera Occidental of the Andes Chain. It lies in a mountainous desert where the steep southwesterly slope of the Andes is dissected by a succession of rapidly downcutting, deep canyons. Local topography is moderately rugged with a dendritic drainage pattern and an elevation of 8000 to 14,000 ft. Volcanic peaks along the crest of the Cordillera rise over 19,000 ft. Local precipitation, including a little snow, amounts to about 10 in. during January and February, but general runoff in the region is slight. Throughout southern Peru the springs and streams are widely separated. Crude canals irrigate small farms on terraced slopes along the streams and provide sparse subsistence to the semi-nomadic inhabitants. During the past decade, engineering and geological explorations of the region, as well as the mineral deposits themselves, have required construction of a network of several hundred miles of roads. Before this, roads extended only a few miles inland. Many areas still can be reached only by trail. Toquepala was briefly described in 19th century geographical literature as a copper deposit, and it received desultory attention from Chilean prospectors early in the present century. It was first recognized as a mineralized zone of possible real importance by geologist O.C. Schmedeman during an exploration trip for Cerro de Paso Copper Corp. in 1937. The discovery was late as compared to earlier recognition of Chuquicamata, Potrerillos, and Braden of Chile and Cerro Verde of southern Peru. This was due partly to the region's difficult accessibility but principally to the obscure character of the outcrop evidence of copper. From 1938 until 1942 Cerro de Pasco Copper Corp. partially explored the deposit by adits and diamond drillholes. This campaign was supplied by a 60-mule pack train continuously shuttling over a 30-mile trail. Northern Peru Mining & Smelting Co., a wholly owned subsidiary of American Smelting & Refining Co., undertook regional engineering stud- ies in 1945 and drill exploration in 1949. According to published data1 the deposit contains 400 million tons of open pit ore averaging a little over 1 pct Cu. It is currently undergoing large-scale development by Southern Peru Copper Corp., which is owned by American Smelting & Refining, Phelps Dodge, Cerro de Pasco, and Newmont Mining. Summary of Geology: The deposit is situated in a terrane composed of Mesozoic(?) and Tertiary volcanic rocks intruded by dioritic apophyses of the Andean Batholith. These formations are exposed in a northwesterly trending belt about 15 miles wide. Along the northeast they are unconformably overlain by Plio-Pleistocene pyroclastic rocks, which occupy much of the crest of the Andes, and along the southwest they are covered by the Moquegua formation of Pliocene(?) age. The mineralized area, oblong in shape and about 2 miles long, has been a locus of intense igneous activity. Several small intrusive bodies having irregular forms occur within and adjacent to a centrally located, large breccia pipe. The mushroom-shaped orebody consists of a flat-lying enriched zone of predominant chalcocite with a stem-like extension of hypogene chalcopyrite ore in depth within and around the pipe. This breccia pipe is relatively large and has been formed by repeated episodes of brecciation. Small satellitic pipes occur at random within a 2-mile radius of this central pipe. These too were individual sourceways of mineralization, although not always of ore grade. Within and around the zone of breccia pipes and mineralization there are a few faults and veins, but these are discontinuous random structures of minor significance. There are no regional or local systems of faults or other planar structures recognized which could account either for the mechanical development of the breccia pipes or for their localization as a group or as individuals. Hydrothermal alteration is pervasive in the zone of mineralization. Clay minerals appear to be abundant in places, but their percentages are undetermined. Quartz and sericite are the principal alteration products, and in many instances original rock textures are obliterated. The principal sulfides, hypogene pyrite and chalcopyrite and supergene chalcocite, occur mainly as vug fillings in the breccia and as small discrete grains scattered through all the altered rocks. Sulfide veinlets are relatively scarce. Sulfides are more abundant and alteration is more intense in certain rock units, such as the diorite and most of the breccias. Although the Toquepala mineral deposit is similar in most respects to the porphyry copper deposits of southwestern U. S., it most closely resembles the Braden deposit of Chile, as described by Lindgren

Jan 1, 1959

By H. D. Outmans

In steady vertical flow, the interface of an immiscible liquid-liquid displacement is horizontal for any flow rate below the critical. In nonvertical flow, however, the shape of the interface in the steady state does depend on the flow rate, and the purpose of this paper is to calculate the unsteady interfaces during the transition of one steady state of flow to another. A knowledge of these transient interfaces is of considerable importance in reservoir engineering where the calculation of breakthrough recovery depends on the instant the interface reaches the producing wells and on the shape of the interface at that time. Although the emphasis is put on transient interlaces, which eventually approach stable equilibrium, it is shown that if the displacement exceeds a critical rate no equilibrium is possible. The interface is then unstable and viscous fingers are formed during the displacement. The critical rate and the shape of the transient and equilibrium interfaces are affected by the effective interfacial tension; but since this effective interfacial tension appears in the calculations only in combination with the inverse square of the thickness of the medium, its effect in the reservoir would appear to be negligible compared to its significance in model experiments. INTRODUCTION Stability criteria and the early growth of interfacial disturbances in a plane parallel to the boundaries of a dipping formation in which oil is displaced by an incompressible fluid were described in a previous paper.l This type of instability is significant in thin reservoirs. However, if the reservoir has appreciable thickness, then interfacial stability in vertical planes, normal to the upper and lower boundaries, also becomes important (the displacement is supposed to be parallel to these vertical planes). The difference between the two stability problems is that, in the first case, the intersections of the interface with planes parallel to the boundaries are normal to the direction of the displacement; in the second case, the intersections, this time with vertical planes, are not normal to the displacement. Instead, they are tilted at an angle which depends on the displacement rate. The tilt of steady interfaces was calculated by Dietz2 who also determined the critical rate of displacement for stability in the vertical plane by assuming that this rate would coincide with an interfacial tilt equal to the dip of the formation. The critical rate thus calculated is the same as has been found for thin reservoirs (see Eq. 1.1 of Ref. 1 and of the present paper). Dietz's calculation of the stable tilt was verified by laboratory experiments and the agreement was found to be fairly good.3 It is doubtful, however, that stable tilts actually exist in the reservoir because a change in production rate is not followed by an instantaneous adjustment of the interface to the new rate but, rather, by a transition period during which the interface changes from one equilibrium tilt to the other. The principal objective of this paper has been to describe these transient interfaces without putting any restrictions on the flow conditions or the shape of the interface, as had been done previously. The second objective was to compute the critical velocity, taking into account capillary effects, and the third was to evaluate, at least qualitatively, the shape of the front at rates above the critical, again without making the simplifying assumptions introduced by previous investigators.2,3 In the following sections two examples are given of the calculation of interfacial motion. The first describes this motion for an initially horizontal interface in a dipping layer, and the second for a vertical interface in a horizontal layer. The mathematical formulation of the problem is nonlinear in the boundary conditions, and this prohibits its solution in closed form. Instead, the solution is obtained in the form of higher-order approximations. 1 Before proceeding to a description of the mathematical model, however, we define two quantities

By R. H. Smith, A. C. Polk

The physical properties of the materials are listed, together with a short explanation of how this material binds the sand grains together without materially reducing the effective permeability of the sand. The chemical can be used in wells with bottom-hole temperatures ranging from 105°F to more than 350°F A description of the equipment required and the techniques used for applying these plastics to the wells is included. Introduction Recovering oil and gas from unconsoli-dated sand formations offers one of the most troublesome of all production problems. These sands generally present no particular trouble while drilling is in progress, but after the well has been completed and a pressure differential has been established across the face of the producing zone, the formation begins to L'slough," resulting in "sanding up" of the well. The term "sanding up" means that sufficient volumes of sand have moved into the well bore or casing to cause a serious reduction or complete halt of all flow of oil, water or gas. In rare cases a well may produce only a small amount of sand and still continue to flow or pump, the sand being carried to the surface in the fluid stream. However, in such instances, the result may be a costly repair bill due to the effect of the sand on surface and pumping equipment. The difficulty of producing petroleum from sands that are loosely cemented has long been recognized by petroleum engineers but only within the last few years has any new approach to the problem been undertaken. This involves the use of plastics that are capable of bonding the individual sand grains in place without materially reducing the effective permeability of a formation. The successful application of plastics for the consolidation of poorly cemented sands is relatively recent but now it is widely used in many of the more difficult areas on the Gulf Coast of Texas and Louisiana. This relatively new use of plastics1 in the oil fields has been preceded by much laboratory and field research on the use of various chemicals2,3 for solving numerous well-completion and work-over problems. Plastics now are being used successfully to control gas-oil and water-oil ratios,4'6 in zone isolation, the repair of casing leaks, the elimination of caving in cable-tool drilling wells6'7 and in the setting of linerss and casing.9 Sand-consolidating plastics, however, are basically different from all others in that they must not form an impervious seal. Field Practices The approach to the sanding-up problem usually has been the mechanical obstruction of the movement of the sand grains.

Jan 1, 1947

By A. C. Polk, R. H. Smith

The physical properties of the materials are listed, together with a short explanation of how this material binds the sand grains together without materially reducing the effective permeability of the sand. The chemical can be used in wells with bottom-hole temperatures ranging from 105°F to more than 350°F A description of the equipment required and the techniques used for applying these plastics to the wells is included. Introduction Recovering oil and gas from unconsoli-dated sand formations offers one of the most troublesome of all production problems. These sands generally present no particular trouble while drilling is in progress, but after the well has been completed and a pressure differential has been established across the face of the producing zone, the formation begins to L'slough," resulting in "sanding up" of the well. The term "sanding up" means that sufficient volumes of sand have moved into the well bore or casing to cause a serious reduction or complete halt of all flow of oil, water or gas. In rare cases a well may produce only a small amount of sand and still continue to flow or pump, the sand being carried to the surface in the fluid stream. However, in such instances, the result may be a costly repair bill due to the effect of the sand on surface and pumping equipment. The difficulty of producing petroleum from sands that are loosely cemented has long been recognized by petroleum engineers but only within the last few years has any new approach to the problem been undertaken. This involves the use of plastics that are capable of bonding the individual sand grains in place without materially reducing the effective permeability of a formation. The successful application of plastics for the consolidation of poorly cemented sands is relatively recent but now it is widely used in many of the more difficult areas on the Gulf Coast of Texas and Louisiana. This relatively new use of plastics1 in the oil fields has been preceded by much laboratory and field research on the use of various chemicals2,3 for solving numerous well-completion and work-over problems. Plastics now are being used successfully to control gas-oil and water-oil ratios,4'6 in zone isolation, the repair of casing leaks, the elimination of caving in cable-tool drilling wells6'7 and in the setting of linerss and casing.9 Sand-consolidating plastics, however, are basically different from all others in that they must not form an impervious seal. Field Practices The approach to the sanding-up problem usually has been the mechanical obstruction of the movement of the sand grains.

Jan 1, 1947

By M. H. Gaskell, D. M. Kehn, G. T. Pyndus

A correlation of the bubble point pressure for black oil systems is developed using the standard physical-chemical equations of soiutions. The correlation is based on 158 experimentally measured bubble point pressures of 137 independent systems and is expressed in terins of the usually measured field pnrameters— flash separation gm-oil ratio, rank oil gravity, total gas gravity, and reservoir temperature. The data were obtained on systems produced in Canada, Western and Mid-Continent01 United States, and South America. The average error (algebraic) in the representation is 3.8 per cent, and the maximum error encountered is 14.7 per cent. INTRODUCTION In the absence of experimentally measured properties of reservoir fluids, it is often necessary for the field engineer to make estimates regarding the fluid properties based on the usually measured producing parameters. To aid in these estimations, various correlations have appeared in the literature in recent years. Among the pertinent properties of interest is the bubble point pressure. A correlation for this parameter has been reported by Standing'. However, this correlation was based essentially on California produced crudes and this limitation was pointed out with its presentation. The correlation presented in this paper utilized data on crude oil systems from Canada, Wes- tern and Mid-Continental United States, and South America. CORRELATION DEVELOPMENT The basic assumption used in this development is the same as employed by Standing', There is a wide variety of ways to combine these parameters; however, in this instance the combination was made on the basis of Henry's law2. Accordingly, the relationship proposed is Although Eq. 2 defines an individual system, it is of limited value since H' is a function of gas-phase composition and the system temperature. It was observed that for the systems where the bubble point was measured at several temperatures that the ratio of the bubble point pressures and the ratio of the corresponding absolute temperatures (R) were practically identical. Thus, for correlation purposes the bubble point pressure may be taken as a direct function of the absolute temperature. This relation is valid only for those systems that are not near the critical point. Accordingly, this correlation will be inadequate for systems in the region of the critical point. The solubility of the various hydrocarbons found in the gas phase increases with the molecular weight. Thus, the saturation pressure should be inversely related to the gas gravity. Applying these principles to Eq. 2 and rearranging terms gives: The variables 02 the left side of Eq. 3 were designated as the "hubble point pressure factor". The number of mols of tank oil per barrel is a function of the "mclecular weight" of the tank oil. Although the tank oil is a complex mixture, it was assumed for the purposes of this correlation that a unique molecular weight could be assigned to a given oil. This was designated as the "effective molecular weight", and was related to the oil gravity, This empirical relationship was developed simultaneously with the correlation by assuming values of M,. and working to obtain a smooth curve for both the correlation and the effective molecular weight. The relationship between the oil gravity and the effective molecular weight used in this correlation is shown in Fig. 1. The effective molecular weight is somewhat higher than the molecular weight of the C fraction. The difference between these values is largest for the low-gravity systems. It is noted that this effective molecular

By J. J. Carrigan

DURING the experimental stage in our use of the electric cap lamp in the Anaconda mines at Butte. Mont., we were somewhat concerned as to how the spitting of fuses would be carried out if we completely eliminated the open-flame light. This problem was at once given serious attention by the engineering research department and some thought was given to having all blasting done by the use of electric delays, which has been the practice for some years

Jan 1, 1936

By F. J. Fayers, J. W. Sheldon

A theoretical discussion is presented of the behavior of the interface between two fluids of different physical properties when displacement is occurring along a thin tilted bed. An approximate equation of motion is deduced for the motion of the interface, suitable boundary conditions are derived and the conditions necessary for the approximation to be valid are determined. Steady-state behavior and the circumstances under which a steady-state interface can develop are discussed. Finite-difference solutions of the equation of motion for two characteristic water-drive problems are presenled. The theory of displacement in a thin bed may be regarded as being the porous-medium-equivalent of the classical "shallow-water wave" theory of hydrodynamics. INTRODUCTION The solution of moving interface problems are important in predicting the behavior of oil reservoirs under various conditions of production. Kidder4,5 has obtained analytic solutions for the fingering problem and for another particular case of the motion of the interface between two immiscible fluids of unequal density in a porous medium. In the present analysis, we analyze the problem of the motion of an interface along a slightly dipping bed whose length is long compared with its thickness. The requirement of a thin bed is necessary in order to give a simple differential equation for the motion. The two fluids are of unequal density and mobility. In the derivation of the equation of motion, it is assumed that the lighter fluid is being injected at constant rate at the high end of the porous layer, while heavy fluid is produced at the low end of the layer. The analysis applies equally well, however, to the reverse procedure in which the heavier fluid is injected at the low end of the tilted layer. It will be shown that the behavior of the system is critically dependent on which fluid has the higher mobility and that the interface can in certain circumstances achieve a simple progressive steady-state shape. The fluids may be considered to be immiscible or miscible. It is assumed, however, that the thickness of the interface region is negligible in comparison with other dimensions of the system, and that the strength of the saturation or concentration discontinuity remains constant during the motion. In conjunction with Buckley-Leverett theory and areal sweep-out calculations, the tilted interface problem is one of the fundamental problems of reservoir engineering; it defines the very important underpassing and overpassing phenomena associated with water-drives, gas-drives and secondary recovery operations. The tilted interface problem has been dealt with previously by Dietz.2 In the present paper, we endeavor to derive the pertinent mathematical results more rigorously, and in doing so we obtain modifications in both the differential equation and boundary conditions for those given by Dietz. We also attempt to show the connection between these results and some of the recent work on the stability of interfaces. Finally, we attempt to demonstrate the practical importance of the thin bed theory by showing the difference in behavior of two characteristic waterflood problems. In the favorable mobility case recovery is improved by increasing production rate, while in the unfavorable case undercutting or overcutting is minimized by reducing the displacement rate. PROPERTIES OF THE EQUATION OF MOTION Fig. 1 illustrates a porous layer of constant thickness H and tilt 8 with Fluid 1 of mobility ?l and density pl below Fluid 2 of mobility ?2 and density p2. The fluids are incompressible and flowing with volumetric flux q along the layer. Both the slope a of the interface with respect to the bed and the curvature of the interface are assumed to be small. What is meant by "small" is indicated in the derivation given in Appendix A of an approximate equation of motion for the interface. Other symbols are defined in the "Nomen-

By R. A. Feemster, C. M. Rader

Because of the necessity for taking regularly occurring open-flow tests in prorated high-pressure oil fields, much gas is turned to atmosphere by way of vertical vent lines leading away from the oil and gas separator. In the past, measurement of such gas has been accomplished by several methods, usually by use of the open-flow Pitot tube. The use of the closed-flow Pitot tube has been avoided apparently chiefly because the ordinary vent-line hook-up makes it necessary to apply the instrument closer to a bend, valve, or obstruction in the pipe than is recommended by rules of good practice. The many advantages that would result from the application of the closed-flow Pitot tube prompted investigation of the actual effect upon quantity rate of flow measurements computed from data obtained with the tube in a normal working position, which is closer to the tee at the base of the vent riser than is usually considered as giving highly accurate results. An effort Was first made to compare the results thus obtained to those under ideal conditions and at high velocities To make this comparison, knowledge of the characteristics of gas flowing at very high velocities is essential. Research for such information indicated that little or no work had been done that would give data necessary for such a comparison, therefore the problem was changed to a test designed to determine the relationship between quantity rates of flow as measured by an orifice meter and a Pitot tube placed at the center of a pipe eight diameters from a tee or ell at the base of a vent riser, through which gas is flowing under low pressures at very high velocities. To determine this relationship, a series of tests was run on a number of 8-in. iron-pipe vent riser., in which the Pitot tube data were taken at the position as stated above. Gas from a wet-gas gathering system was passed through an orifice meter setting and thence to atmosphere by way of the vents. Data were taken simultaneously from the orifice meter and Pitot tube from which computations for comparisons were made. The actual method of comparison is discussed later in this paper. Since Pitot-tube information is usually given in general terms, and not readily usable, it will be the purpose of this paper to discuss the applica-

Jan 1, 1934