Search Documents

By John E. Sherborne, William M. Newton

The relation between the properties of electric logs and the fluid used in drilling a well is briefly discussed in this paper, and the fact that the resistivity of the drilling mud and its filtrate can appreciably affect such logs is shown. Apparatus was designed and a procedure established to determine the effect of various factors on the resistivity of drilling mud. Five muds commonly employed in California were tested and the following observations were made: I. The effect of raising the temperature from 80°F. to 180°F. is to decrease the resis-tiviiy of the mud or filtrate approximately 50 per cent. 2. The resistivity of the mud in most cases closely approximates that of its filtrate. 3, The change in the resistivities of muds caused by the addition of chemical is not the same function of the amount of chemical added for each mud. 4. The effect produced by increased sodium chloride content is to reduce markedly the resistivity of the mud and its filtrate. 5. Weighting materials, such as Baroid and limestone, tend to increase the resistivity of drilling mud. 6, Cement and counteracting reagents reduce mud resistivity. Introduction During recent years, the practice of "electrically logging9' a geologic formation by means of a system of electrodes lowered in a well bore has provided data of inestimable value concerning the nature of the sediments penetrated. Thus, it is generally possible, by means of electric logs, to distinguish readily the differences between shales, sandstones, cherts, limestones, and other rock forms. The distinguishing characteristics recorded in this manner have made possible long-range and closely detailed mapping and visualization of deeply buried structures1-5 to a degree not to be obtained with a reasonable expenditure of money by any other means at present in use. Besides being of value in correlation work, electric logs have been found, in some instances, to be useful in estimating the nature of fluid contained within the pores of a rock. In special cases, even the relative permeabilities at different horizons have been determined.6 That electric logs should reflect in some measure such physical properties of rocks as porosity and permeability and, in addition, give rise to data pertaining to the fluid content of rock interstices, becomes evident when the conditions giving rise to the electrical phenomena measured are known. However, it is not the purpose of this paper to review the present status of electric logging; rather, the reader is referred to the papers cited on page 220 for the principles and practice involved. Importance of Drilling FLuid in Electric Logging Because the drilling fluid must be the medium through which the electric logging device is made to traverse the formations penetrated by a borehole, and since, in general, the drilling mud completely surrounds

Jan 1, 1942

By George A. Johnson, Leon H. Banks

The Missouri-Kansas Zinc Corpn., operating in the Waco district, 15 miles northwest of .Joplin, Mo., owns large tailing piles made during milling operations of the years 1918-28 by the Butte-Kansas, Acme, and Barnsdall mining companies, whose holdings have been purchased and consolidated under the ownership of the Missouri-Kansas Zinc Corpn. These tailings had been considered too low in value to be worth retreating by the ordinary methods. C. Erb Wuensch, consulting engineer of the Missouri-Kansas Zinc Corpn., noted the difference in the type of tailing from upper-level and lower-level ore. The latter contained hard lime chats. He also found that mill losses had been due to particles of blende on the corners or sides of the chats and to the existence of soft, porous, cellular, lime chats containing varying amounts of blende. He conceived the idea that a quick grind in rolls or hall rnills might change the type of the rnaterial so that jigging could rnake a clean tailing for discard and a partly concentrated product sufficient in blende content to justify the expense of fine grinding in hall mills to free the mineral entirely. A laboratory was equipped with the necessary machines and the writers were assigned the problem of developing a method of retreating the tailings. Laboratory Testing From preliminary drill sampling of each pile was obtained the blende content, the soluble sulfate content, and the general characteristics of the material to he treated. The tailings were a mixture of lime and flint with some shale. Visual examination showed most of the blende to be in the dolomite and very little in the flint, although there were some flint particles with blende on the cleavages. The blende was found as particles on the corners or cleavage faces in one type of chat and in another disseminated in a soft, porous, cellular lime. Because of the porosity of the latter type of chat, the apparent specific gravity, under hindered-settling conditions, is less than that of a solid piece of lime or flint. That it,

Jan 1, 1930

By T. PH. D. Egleston

THE origin of gold both in placer deposits and in veins, and especially the origin of nuggets, has been the subject of repeated discussions and investigations, which have been recently brought to my attention by several extremely interesting specimens sent to me for examination, and more especially by the one exhibited at the meeting of the Institute in February, 1880.* In the year 1874 I made some examinations of the hydraulic mines of Califor¬nia, and was very much struck with the distribution of the gold throughout these deep placers, which were almost invariably poor on' the surface, while gradually growing richer towards" the bed¬rock. The constant presence of fossil wood, and the large quantity of organic matter contained even low down in these beds, was also remarkable. Not being satisfied with the various theories advanced to account for the formation of these deposits, I began an investiga¬tion early in the year 1879 on the conditions of solubility of gold and the causes of the loss in working gold ore in a large way: The researches which I have undertaken show that gold must be considered a soluble rather than an insoluble metal, and that the conditions of solution are such as will be found anywhere where gold is likely to occur, and the solution may take place even under the ordinary cir¬cumstances of surface drainage, and may be going on freely even where the presence of gold has never been suspected, and that there are causes enough in nature to produce the solution of the gold in sufficient quantities to account for all the phenomena of both the vein and placer formations. The general theory with regard to the formation of these placer deposits and nuggets has been that they were the result of the de¬struction of pre-existing- vein-matter, which does not accord with the facts as shown in the deep placer deposits. The gold in such case would be distributed in layers of unequal richness throughout * Transactions of the American Institute of Mining Engineers, vol. 8, p. 451.

Jan 1, 1881

A. Cook K.A. Grace's article advocates usage of the terms describing resources as defined by the US Bureau of Mines (USBM) and the US Geological Survey (USGS). Originally recommended in 1943, the terms were revised in 1976 and again in 1980. Mr. Grace further recommends that the term reserves should be severely restricted and that it should encompass mining and processing factors. The list of references quoted in the article does not, however, mention the study concerning reserves that was made over a period of almost four years by a joint Committee on Definitions. This committee was sponsored by three societies - the American Institute of Mining, Metallurgical, and Petroleum Engineers (AIME), the Society of Economic Geologists (SEG), and the American Institute of Professional Geologists (AIPG). Most of the detailed work was done by a working party appointed by the Society of Mining Engineers (SME) of AIME. After studying previous definitions in the US as well as in the United Kingdom, Canada, Australia, France, and other European countries, the following definitions were proposed and accepted in 1974 by the SME board of directors. (Ore reserve definitions in Rhodesia, South Africa, or New Zealand were not mentioned as having been reviewed. Table 1 lists definitions from MINING ENGINEERING, July 1975. Notice in Table 1 it was mentioned, under Resources, that the definitions of reserves were recommended for the purposes of commercial evaluation. It was further stated that the terminology adopted by the USBM and the USGS, as released to the public, covering resources, was recognized as such. Mr. Grace also recommends that reserve calculations should allow for future losses in ore tonnage, ore grade, milling, and smelting. Unfortunately, it might take years to develop a prospect after it has been discovered. Mining methods have to be tested before being finalized in order to know what tonnage of ore is going to be lost, or how much dilution is likely to occur. The same problems are present in concentrating or in smelting. Operating mines usually know how mined grade compares with ore reserve grade. They can usually predict fairly closely what their final metal recoveries are probably going to be. It is, however, expecting too much to have to delay quoting reserves from say a recently drilled prospect. Any responsible mining geologist or mining engineer (or company for that matter) should state several things about an ore reserve calculation: that it is or is not a preliminary estimate only; that estimated grades have not been diluted to allow for a future, as yet unknown, mining method; that metal recoveries are or are not only tentative, based perhaps on drill hole samples only or on no metallurgical testing at all. [ ] Reserves of a partially explored prospect are always quoted when it becomes necessary to raise capital. If they are described as preliminary only (really just tonnage and grade estimates and not true "reserves") in addition to being accompanied by some of the items just mentioned, nobody is going to be misled. If, on the other hand, a report by a member of the SME or SEG is intentionally misleading, the individual must be reported and eventually disbarred from his or her society. To summarize, let us stay with the definitions of ore, ore reserves, and related terms as recommended and accepted by SME. I might add that on occasion I have used a fourth category in my ore reserve calculations, namely Geologically Possible Ore. This category is more or less the same as Inferred ore defined by the USBM and USGS. I have never given a grade to this category, which may be based only on geological mapping, geochemical sampling, or geophysical traversing. ?

Jan 1, 1986

By Ernest F. Burchard

A Reconnaissance of the manganese- and chrome-ore deposits of Cuba was made by the writer, as a representative of the U. S. Geological Survey, in company with Mr. Albert Burch of the Bureau of Mines, under instructions of the Secretary of the Interior, in the spring of 1918. The Cuban Government courteously detailed Sr. E. I. Montoulieu, a mining engineer connected with the Treasury Department, to act as escort and associate throughout the work on the island. The object of the study was to obtain authentic information for use of the United States Government as to the location, character, quantity, and availability of the manganese- and chrome-ore deposits in Cuba. Accordingly, the work comprised examination of such deposits as seemed to be of promise, without regard to stage of development, with a view to a determination of the quantity and quality of ore likely to become available for shipment during 1918 and 1919, and of the tonnage of ore in reserve. Wile it was possible to visit most of the deposits that seemed to be of promise, there was not sufficient time to visit all that were brought to our attention, some of which may have merit. Moreover, the necessity for paying particular attention to the ore deposits and the mines precluded the possibility of making more general studies of the geology of the region, and of making satisfactory collections of country rock and of fossils, and so for other details as to the geography and geology of Cuba the reader is referred to the report by Hayes, Vaughan, and Spencer.l Mr. Burch returned to the United States about 10 days in advance of the writer, who continued, in company with Sr. Montoulieu, investigations of reported deposits in Pinar del Rio, Matanzas, and Santa Clara Provinces. On his arrival in Washington, Mr. Burch submitted to the Director of the Bureau of Mines a summary of the results of the work to date. Later the writer published, as Press Bulietin 190. 380 of the U. S. Geological Survey, a statement concerning the chrome and man-

Jan 1, 1920

By W. W. Yankie, A. T. Chatas

This paper is written as a discussion of the paper, "Buckling of Tubing in Pumping Wells, Its Effects and Means for Controlling It" by Arthur Lubinski and K. A. Blenkarn, which war published in the March, 1957, issue of Journal oP Petroleum Technology. An analogy is drawn between the buckling of tubing in pumping wells and a fiube, fitted with frictionless pistom, linked by an inelastic rod, and which is subject to an internal pressure. A simple derivation shows that the critical internal pressure exerts a hydrostatic force on the pisfon which is close to the Euler load for compression buckling of the same tube. While the results agree with those of Ref. I, the basis of calculations has been changed and clarified. The presence of internal upsets at the pistons is discussed. INTRODUCTION In the Appendix, Lubinski and Blenkarn state that a tube with ends closed by frietionless pistons connected by an inelastic rod (Fig. 1) will behave as a column loaded with a force equal to the tension force in the rod. They note that, while the fluid may not resist a shear force, the moment in every cross section is piston force multiplied by the elastic line deflection (c.f., the loaded column). Since the equations of the elastic lines are similar in the two cases, the solution is carried over from the loaded column. On the contrary it is suggested that while the method of solution remains unchanged from the column case, the actual stress distribution is different, a fact which is taken into account in this note. A simple method of approximating the buckling pressure is given, and their reasoning in our mathematical language is continued. GENERAL EQUATIONS The equation of an elastic line, initially straight in the x direction (Fig. 2), is given by In the case of a loaded column, this may be written: For the pressurized tube it was shown, by analogy with the loaded column, that tion has a solution that, for P, = EI/P, any deflection is stable (a criterion for buckling). An attempt will be made to describe more precisely, the forces acting on the tube, and to analyze the buckling condi,tions. DISCUSSION If the tube assumed a deflected position, the volume between the pistons would increase so that in deflecting, the energy of the fluid would decrease. When the increase in elastic energy of the tube (due to bending) is equal to the decrease of fluid pressure energy, buckling conditions exist. Analyzing the forces on the tube (Fig. 3), two transverse forces, T,, T,, exerted by the pistons, are balanced by a resultant of the pressure elements which are linearly dependent on the local curvature of the elastic line (Fig. 4). Unlike most buckling cases, the forces depend on the shape of the elastic line, a condition that makes a rigorous mathematical treatment difficult. Several approximations may be used to clarify the problem.

By William L. Boyd, Eugene L. McCarthy, Laurance S. Reid

Proper control of the moisture content of natural gas is essential to reliable operation of gas transmission and distribution facilities serving northern markets. The moisture content of natural gas is usually determined by dew point measurement at the existing pressure. For any gas of constant moistrire content. the dew Point varies with the pressure. A correlation of the data of several investigators is prezented in graphical form by the authors. These data were correlated by the authors and F. M. Townsend, C. C. Tsao. M. I). Rogers. Jr.. and J. A. Porter. graduate students in chemi(.a1 engineering at the University of Oklahoma. Of articular interest are the hitherto unpublished low temperature data observed by Wickliffe Skinner. Jr., which are included in this correlation. PRESENTATION OF DATA The problem of interpreting water dew points, or saturation temperatures. of natural gas in terms of specific moisture con-tent has increased in importance during the past decade bec.arl.;e of extensive development.; in the transmission and petro-chemical phases of the natural gas industry. Virtually all gas transported to northern and eastern markets must be dehydrated to a low water vapor content to prevent hydrate formation in transmission and distribution lines and resultant interruption.; in gas deliveries. Complete dehydration is required in certain phases of tile petro-chemical industry involving low-temperature operations. It is a well-known fact that the water vapor content of pure hydrocarbon vapors and their mixtures at superatmospheric pressures cannot be predicted with accuracy by assuming validity of the ideal gas laws." Earlier interest in the general problem was concentrated on the water vapor content of pure hydrocarhons and hydrocarbon mixtures in the pressure and temperature ranges common to gas and oil producing reservoirs in order to obtain fundamental data for the improvement of production techniques and the furtherance of reservoir studies. Excellent data are published for pressures ranging from atmospheric to 10,000 psig and for temperatures ranging from 100° to 460° F4,9,10,11 and are found to be in close agreement. However, experimental data at high pressures and temperatures below 100°F are comparatively limited in scope. Experimental data in the lower temperature range have been reported by Laulhere and Briscoe.8 Deaton, et al,2,3 Hammerscllmidt,5,6 and wade," In general, the pressures employed in these investigations ranged from atmospheric to 1.000 psig while temperatures ranged from 32° to 120°F; i.e., the usual conditions encountered in gas transmission line operations, Additional data were reported by Russell, et al,12 at pressures as high as 2.000 psig and covering a rather narrow atmospheric temperature range. In 1947, Hammerschmidt published a correlation of all available data,' in which the water vapor content of gases at saturation. under high pressure and low temperature. was predicted by extrapolation. In 1948, Wickliffe Skinner. Jr.. presented data on the moisture content of a low nitrogen content gas at low temperature and at pressures ranging upward to 1.500 psia.1-3 Comparison of Skinner's experimental data with the extrapolated data of Hammerscllmidt revealed an appreciable variation in the lower temperature range. emphasizing the need for a new correlation which would rely on Skinner's data at lower temperatures. Careful scrutiny of available data suggested that presence of an appreciable quantity of nitrogen in a gas mixture may affect its saturated moisture content so that data obtained from gases with more than three per cent nitrogen were not used in this correlation. CORRELATION OF DATA Data employed in this correlation are presented in Table I. The data of Dodson and Standing.4 McKetta and Katz,9 and Olds, Sage and Lacey10 were compared and found to be in close agreement so that the data of Olds. et al, re-plotted in a more convenient form by the Humble Oil and Refining Co.,' were used for temperatures of 100°F and above. Skinner's data were used for temperatures below 40°F. Between these intermediate temperature limits, the data of Hammerschmidt.7 Wade" and extrapolated data of Olds. et al.1 were tabulated

Jan 1, 1950

By Morris Muskat, J. M. McDowell

In both production and refining operations of the oil industry many processes are controlled by the gas-liquid phase relationships of the hydrocarbon mixtures of interest. The quantitative behavior of fractionating or distillation columns and stills depends on the changes in the equilibrium distributions of the hydrocarbon components between the gas and liquid phases as the pressure or temperature conditions may vary along the length of the column or as the gross operating parameters and compositions are varied. In oil producing operations the nature and amount of gas phase developed within an underground reservoir as it is being depleted and its pressure declines also involve the basic equilibrium gas-liquid phase interactions. The influence of surface conditions of temperature and pressure and various separation procedures on the nature and amount of stock tank oil and natural gas recovered from a given well stream is likewise determined by the same basic phase equilibrium characteristics of the hydrocarbon systems. Such equilibrium separation of the gas and liquid phases in a well stream is of importance both in establishing optimum separator conditions for obtaining maximum stock tank oil yields and in the general problem of crude stabilization. The phenomena involved in these problems and their quantitative aspects can, of course, be established in each individual instance by appropriate laboratory experimentation. It has been found, however, that by associating with the individual hydrocarbon components functional characteristics de- scribing their individual gas - liquid phase equilibrium behavior, the phase properties of the composite mixtures can be predicted by mathematical computation. These characteristics have been termed "equilibrium constants", or "equilibrium ratios"," and are defined by the general equation: where K, is the equilibrium ratio for the jth component, y, is the rnol fraction of that component in the gas phase, and xj is the corresponding mol fraction in the coexisting liquid phase. Considering the Kj as representing available and measurable properties of the individual components of a mixture, and as defined by Eq. (l), it is readily shown that in a coexisting gas-liquid system the rnol fraction concentrations of the individual components in the gas phase, y,, and those in the liquid phase, x,, are given by the expressions: where the nj are the corresponding rnol fraction concentrations in the composite system, and ng is the mol fraction of the whole which is in the gas phase. The basic unknown in Eq. (2) is n,: which gives the gross separation between the gas and liquid phases. This may be determined in principle by imposing the requirement that the sums of the mol fractions in both the gas and liquid phases are unity, i.e. by the equations: The solution of the equivalent Eqs. (3) lying between 0 and 1, when inserted into Eqs. (2), provides a complete description of the compositions of the coexisting gas and liquid phases. While the Eqs. (3) are essentially equivalent to polynomial equations, such transformations are of little value when dealing with multicomponent sys-

Jan 1, 1949

By J. M. McDowell, Morris Muskat

In both production and refining operations of the oil industry many processes are controlled by the gas-liquid phase relationships of the hydrocarbon mixtures of interest. The quantitative behavior of fractionating or distillation columns and stills depends on the changes in the equilibrium distributions of the hydrocarbon components between the gas and liquid phases as the pressure or temperature conditions may vary along the length of the column or as the gross operating parameters and compositions are varied. In oil producing operations the nature and amount of gas phase developed within an underground reservoir as it is being depleted and its pressure declines also involve the basic equilibrium gas-liquid phase interactions. The influence of surface conditions of temperature and pressure and various separation procedures on the nature and amount of stock tank oil and natural gas recovered from a given well stream is likewise determined by the same basic phase equilibrium characteristics of the hydrocarbon systems. Such equilibrium separation of the gas and liquid phases in a well stream is of importance both in establishing optimum separator conditions for obtaining maximum stock tank oil yields and in the general problem of crude stabilization. The phenomena involved in these problems and their quantitative aspects can, of course, be established in each individual instance by appropriate laboratory experimentation. It has been found, however, that by associating with the individual hydrocarbon components functional characteristics de- scribing their individual gas - liquid phase equilibrium behavior, the phase properties of the composite mixtures can be predicted by mathematical computation. These characteristics have been termed "equilibrium constants", or "equilibrium ratios"," and are defined by the general equation: where K, is the equilibrium ratio for the jth component, y, is the rnol fraction of that component in the gas phase, and xj is the corresponding mol fraction in the coexisting liquid phase. Considering the Kj as representing available and measurable properties of the individual components of a mixture, and as defined by Eq. (l), it is readily shown that in a coexisting gas-liquid system the rnol fraction concentrations of the individual components in the gas phase, y,, and those in the liquid phase, x,, are given by the expressions: where the nj are the corresponding rnol fraction concentrations in the composite system, and ng is the mol fraction of the whole which is in the gas phase. The basic unknown in Eq. (2) is n,: which gives the gross separation between the gas and liquid phases. This may be determined in principle by imposing the requirement that the sums of the mol fractions in both the gas and liquid phases are unity, i.e. by the equations: The solution of the equivalent Eqs. (3) lying between 0 and 1, when inserted into Eqs. (2), provides a complete description of the compositions of the coexisting gas and liquid phases. While the Eqs. (3) are essentially equivalent to polynomial equations, such transformations are of little value when dealing with multicomponent sys-

Jan 1, 1949

By FRANK COLE

THE territory covered in this discussion includes all the states west of the Mississippi river. Agriculture is expanding each year in this section, but until recent years the application of commercial fertilizers as an aid to crop production was not practised to any great extent. The use of commercial fertilizers has increased somewhat, but is still on a small basis as compared with the tonnages used else- where in the United States. During 1928 these western states used 665,100 tons of all classes of fertilizer as compared 'with 7,933,600 tons used in the whole United States; or this western area, compromising near- ly two-thirds the land area, uses about 5 per cent of the total fertilizer. To show how large a tonnage one state may consume, North Carolina for the year 192s used 1,349,360 tons of commercial fertilizer or about twice the amount used by 22 western states.

Jan 1, 1930

By C. R. Johnson, R. A. Greenkorn, L. K. Shallenbarger

This paper describes a study, based on core data, of the directional permeability of a sandstone reservoir. Directional air permeabilities are explained and correlated with lithology by the tensor theory of permeability, which is extended to the more general case of heterogeneous anisotzopic porous media. In this case, the permeability tensor is made up of two components: (I) anisotropy (variation around a point) which correlates with bedding, and (21 heterogeneity (variation from point-to-point) which correlates with grain size. INTRODUCTION Previous studies of directional permeabilityl.5-8 have concerned themselves only with anisotropy at a point, rather than with both point-to-point differences and local anisotropies. In this paper, we present the existing tensor theory of permeability for anisotropic porous media and then extend it to the more general case of heterogeneous anisotropic porous media. The laboratory measurements of directional permeability are explained in view of this extended theory and the data are discussed in terms of the lithologic factors that correlate with it. The results show what the heterogeneity and anisotropy of the reservoir element are, and that the directional permeability correlates with lithology. Data used in this paper are measurements of air permeability in eight directions, spaced at 45° intervals, on 142 2-in. vertical plugs from 30 cores. The core data are meaningful in terms of directional permeability because the cores were oriented to within 45O during drilling and coring.3 Although we initially thought that only 60 per cent of the core material was reliable, subsequent study showed that almost all of it was reliably oriented. After determining the air permeabilities, the data were reduced to three independent variables for each plug: the major and minor permeability axes, and the direction of the major axis. These were obtained by converting the permeability data to the reciprocal square root of permeability and fitting the transformed data with ellipses according to the tensor theory of permeability.8 The point-to-point areal variation of the minimum permeability axis is related to grain size. The direction of the permeability axes, where the major axis exceeds the minor axis by at least 5 per cent (measured variation is about 4 per cent), correlates with the bedding. The permeability tensor used in this study must be considered as the sum of a scalar and a tensor, with the scalar being the minor axis permeability as a function of position, and the tensor the directional effect, which is additive permeability over the minor axis. In this case, the point-to-point variation or heterogeneity (minor axis) is substantially larger than the variation at a point or anisotropy. It may be important that this separation of "directional permeabilities" be recognized when considering migration of fluids due to permeability variation. Local migration may be due to anisotropy and point-to-point migration may be due to heterogeneity, but the direction and magnitude of these may not be the same. Furthermore, in truly heterogeneous systems, one would expect that anisotropy would be the smaller of the two effects. THEORY TENSOR THEORY OF PERMEABILITY FOR ANISOTROPIC POROUS MEDIA8 Darcy's law for flow in porous media in its usual form is where qis the flow rate vector, k is the permeability, is the viscosity, is the vector differential operator, and P is the Pressure. Consider flow, q, through a unit area in the direction of the unit vector n from elementary flow tubes parallel

Jan 1, 1965

By Archer E. Wheeler

IN the copper industry, the year 1942 was one of striving for larger tonnage and increased production. The demands of the war program placed copper high in the list of strategic metals and the Government encouraged production by offering a premium of 5c. per pound for copper output in excess of the 1941 quotas. This had the effect of increasing the tempo of existing operations and also of initiating a number of projects which will eventually result in production from sources not hitherto exploited. No radically new methods of copper reduction were reported.

Jan 1, 1943

By W. E. D. Stokes

The faster that aircraft fly the sooner some new and stronger material must be found to take the place of the present aluminum alloy used in all-metal planes. Experts of the National Advisory Committee for Aeronautics. in studying hi-speed aircraft, are convinced that the present all-metal plane, of semi-monocoque, aluminum alloy construction, is not the ultimate in aircraft design. Magnesium alloys and steel are under consideration.

Jan 1, 1942

By D. N. Dietz

A method for determining average reservoir pressure is presented, which is simpler to apply than that devised by Matthews. Brons and Hazebroek. For bounded reservoirs, identical results are obtained if stabilized-flow conditions prevail. The present method yields inferior results in the transient state. The method can, with a slight modification, also be used for water-drive reservoirs. INTRODUCTION In the method proposed by Matthews, Brons and Haze-broek' for determining average reservoir pressure in a multi-well reservoir, the cumulative production (the production time of each well) enters twice: once when the buildup is plotted against In (t + t)/At to arrive at p*, and a second time when the correction, p*-p is determined with one of the several formulas for differently shaped drainage areas. Once a steady state has been attained, however, the previous production history should be immaterial. The same pressure distribution could have been arrived at after different cumulative productions of the individual wells. In principle, therefore, it should be possible to determine average pressures without referring to cumulative productions. In the following paragraphs an expression is presented for the difference between the pressure in a producing well and the average pressure of its drainage area. Then the build-up time needed to overcome this difference is indicated. CASE OF A CIRCULAR DRAINAGE AREA AND A CENTRAL WELL PRESSURE DISTRIBUTION BEFORE SHUT-IN The general differential equation of radial flow (see Muskat, Eq. 10.2) may be written In the steady state, the rate of production of the well is equal to the rate of expansion of the fluid contained in the the drainage area; thus

Jan 1, 1966

By F. D. George, M. J. Salkind

Al3Ni whisker-reinforced aluminum was found to exhibit good Charpy impact toughness and little notch sensitivity even though its room-temperature tensile elongation parallel to the whiskers is only 2 pct. This impact behavior was maintained d liquid nitrogen temperature (-196"C). It is postulated that this behavior is due primarily to the presence of the continuous aluminum matrix which provides sufficient 10calized ductility in the vicinity of the crack tip to absorb considerable energy from the advancing crack. The impact behavior of Al-Alni was found to be quite anisotropic. Of six orientations studied, the transverse orientation having the notch normal to the whisker axis was found to exhibit the lowest impact energy, whereas the transverse orientation having the notch parallel to the whisker axis was found to exhibit the highest impact energy. A significant differnce was noted between the impact behavior of material containing needlelike whiskers and that containing bladelike whiskers. Only two of the six orientations studied exhibited complete fracture for the material containing needlelike whiskers. On the other had, most of the specimens containing bladelike whiskers exhibited complete fracture. It was postulated that the bladelike whiskers block transverse flow, thus reducing the amount of plastic deformation ahead of the crack tip. One of the more significant advantages of composite materials is the prospect of combining high strength with toughness. In general, toughness is associated with materials which exhibit considerable ductility and can deform plastically in the presence of a stress concentration. Very strong materials which resist plastic deformation generally exhibit low toughness. At first glance, then, it would appear as though strength and toughness are mutually incompatible so that useful engineering materials would have to be a compromise between the two. One approach to the problem of combining the high intrinsic strength of ceramics with the toughness of metals was to mix them together to form a cermet. Unfortunately, the toughness of cermets was found to be rather disappointing. Whisker reinforcement of metals, however, appears to be a more promising approach. It has been demonstrated that whisker-reinforced metals produced by unidirectional solidification exhibit enhanced strength due to the presence of high strength nonmetallic whiskers. The total strain capacity of these composites in the direction of fiber alignment is limited to that of the fibers, the matrix being unable to carry the load once the fibers have failed. A characteristic, then, of whisker composites is low ductility in the direction of whisker alignment, on the order of a few percent elongation. This low elongation, which is usually associated with brittle behavior, should not be taken as an indication of low toughness. Such a material can exhibit significant ductility in directions other than parallel to the fibers7 and can therefore possess significant intrinsic toughness. Toughness in a fiber-reinforced metal is derived from several mechanisms. The first is due to the toughness of the matrix itself. A continuous ductile metal matrix can act as an effective crack arrest medium by undergoing localized plastic deformation. Cracks initiated from the surface of the composite or from a brittle fiber failure must travel through the matrix before reaching another brittle phase particle. A second crack arrest mechanism peculiar to fiber composites is due to the fact that, as a crack travels through the matrix and approaches a fiber, the plastic deformation ahead of the crack tip will result in loading of the fiber. This causes the matrix shear strength in the plastic zone to be apparently higher, thus extracting more energy from the crack and diverting the crack at an angle to the original direction of propagation. A third crack arrest mechanism occurs in fiber composites which exhibit a weak bond between fiber and matrix. The idea was proposed by Cook and Gordons that if a crack propagating transversely in a fiber composite were made to turn and run along the fibers by decohesion of the fiber-matrix bond, then toughness would be imparted by the blunting of the crack tip and the creation of new surfaces. The last mechanism, interfacial decohesion, is commonly noted in naturally occurring fiber composites such as wood, bone, and bamboo, and has been observed in man-made composites such as glass fiber-reinforced resins,g silica fiber-reinforced aluminum," laminated steel," and tungsten and silica fiber-reinforced electroplated copper.'' The first mechanism, crack arrest by plastic deformation in the matrix, has been noted in tungsten wire reinforced cast copper." The purpose of this investigation was to quantitatively assess the toughness of a whisker-reinforced metal as a function of orientation. Previous investigation considered only cracks propagating nominally perpendicular to the reinforcement. In this investigation, crack propagation in three mutually perpendicular directions as well as three intermediate orientations was investigated. The system chosen for study was the unidirectionally solidified A1-A13Ni eu-tectic alloy which has a microstructure consisting of 10 pct by volume of A13Ni whiskers in a matrix of aluminum This material exhibits two different kinds of whisker morphology, depending upon the rate at which it is solidified.' At low rates of solidification (less than 2 cm per hr) the whiskers are bladelike, whereas at higher rates of solidification they are

Jan 1, 1969

By E. S. Messer

A knowledge of the magnitude of the irreducible inter.;titial water in a porous medium is so important to petroleum engineering that its determination has become routine in core analyses. The method of determination, being a production problem, should encompass the basic requirements of simplicity in technique and calculations, with reproducible results obtainable in a short interval of time. The results of the evaluation tests outlined in this report indicate that the evaporation method for determining the irreducible water is a technique which meets the requirements. The procedure consists, as the name implies. of permitting the saturant in the pore spaces to evaporate until only an irreducible volume remains. The determination of this volume can be made either graphically or by a mathematical comparison of fluid flows; the time required for each determination being dependent on the fluid used. When fluids other than those having reservoir characteristics were used, a volume factor had to be calculated which was based on the relative volume of various liquids adsorbed on grain surfaces and retained in pores. This factor made possible the calculation of an irreducible water volume when more volatile fluids such as toluene and benzene were used as the saturants. Also presented is the theoretical discussion necessary for the calculation of the capillary pressure as determined from the evaporation curve. A comparison is made between the calculated values and those obtained by experimental means. INTRODUCTION In all geological formations there exists, in the pore spaces of the rock structure, water that is held in a state of equilibrium between capillary and hydrostatic forces. "Interstitial water" is the term given to this water and is defined as that water coexisting in the pore space with the oil prior to exploitation. The term ''connate water" has often been used synonymously with this term; however, this can be true only by a specific definition since, geologically, it means the water in place at the time the rock structure was formed. The quantity of the interstitial water is a variable factor in any formation, since it depends on the hydrostatic forces present in any multiple-phase system. These forces may become unbalanced by the introduction of an extraneous force such as the raising or lowering of the "water table" or the migration of oil into a water-filled formation. Any unbalanced force results in a change in the interstitial water. There exists, however, an irreducible interstitial water. for a particular sand, that is the fraction of the pore space occupied by water when the capillary pressure at the particular point in question is at an equilibrium with the hydrostatic head of the oil sand in the reservoir. For this discussion the term "irreducible water saturation" will be used in place of "irreducible interstitial water saturation" for the sake of brevity; however, they are understood to be identical. A great amount of work has been devoted to the theory and methods for studying the irreducible water saturation and its related capillary pressure. As a result of the publications of Leverett;' Hassler, Brunner and Deahl;2 Calhoun and Lewis;3 and others, the role of capillary pressure studies is being accepted by the industry as a tool for studying suhsurface phenomena. Many techniques have been developed and published for determining the capillary pressure and irreducible water. In general, these techniques may be grouped into three classifications. One of the first was the capillary pressure method described by Leverett1 and expanded by Bruce and Welge.4 The experimental results were compared with water saturation of cores obtained using oil-base mud. Thornton and Marshall compared the irreducible water saturation of core samples determined by the capillary pressure method and by salinity and reported good agreement between the two methods. The second classification for determining the irreducible water and capillary pressure may be referred to as the "centrifugal force method." The general technique is similar to the capillary pressure method except that the force driving the reservoir fluid from the sample is of a centrifugal nature. A complete description of this method was presented by J. J. . McCullough and F. W. Albaugh.6 A process, the reverse of the capillary pressure method, was presented by W. R. Purcell.7 Mercury under pressure is driven into the pores of the rock and the saturation of the core determined at each applied pressure. The resulting capillary pressure curve is used to evaluate the irreducible water saturation. The techniques mentioned are singular in their approach to the irreducible water saturation. In all cases. an external force was applied to the core. The forces employed in the evaporation method are the vapor pressure of the liquid causing evaporation, the kinetic diffusion forces. adsorptive forces and. to a lesser degree, the viscous forces resisting flow to the surface. The basic definition of irreducible water is that water held in a state of equilibrium between capillary and hydrostatic forces This water has been described by previous investigators as being held in the microcapillaries too small to support fluid flow. Actually, this fluid volume is made up of the water in the microcapillaries and as a film adhering to the surface of the crystals. All capillaries. therefore, possess some liquid as a film, the thickness of the film being dependent on the properties of the fluid and solid. A discussion of experiments with references pertaining to the measurement of this immobile layer next to the solid surface can be found in the text by J. J. Bikerman.8 Eversole and Lahr calculated the thickness of this layer to be in the order of 10 ' to 10' cm for aqueous solutions and glass. Between two quartz surfaces they found the thickness to be 2 x 10 cm. The work of Volkova, on the capillary movement of water and toluene in quartz grains, indicated the thickness of the Immobile layers to be near 10' cm. Since any measurement is an average value, it is easy to understand that an absolute value would depend on the roughness of the surfaces involved and the complexity of the system. A calculated effective pore radius of 2 x 10 cm is obtained at the, irreducible saturation of a porous media in a water-air system when a capillary pressure of 100 psi is applied. Since the separation of the sand grains is of the same approximate magnitude as the immobile layer.

Jan 1, 1951

By E. S. Messer

A knowledge of the magnitude of the irreducible inter.;titial water in a porous medium is so important to petroleum engineering that its determination has become routine in core analyses. The method of determination, being a production problem, should encompass the basic requirements of simplicity in technique and calculations, with reproducible results obtainable in a short interval of time. The results of the evaluation tests outlined in this report indicate that the evaporation method for determining the irreducible water is a technique which meets the requirements. The procedure consists, as the name implies. of permitting the saturant in the pore spaces to evaporate until only an irreducible volume remains. The determination of this volume can be made either graphically or by a mathematical comparison of fluid flows; the time required for each determination being dependent on the fluid used. When fluids other than those having reservoir characteristics were used, a volume factor had to be calculated which was based on the relative volume of various liquids adsorbed on grain surfaces and retained in pores. This factor made possible the calculation of an irreducible water volume when more volatile fluids such as toluene and benzene were used as the saturants. Also presented is the theoretical discussion necessary for the calculation of the capillary pressure as determined from the evaporation curve. A comparison is made between the calculated values and those obtained by experimental means. INTRODUCTION In all geological formations there exists, in the pore spaces of the rock structure, water that is held in a state of equilibrium between capillary and hydrostatic forces. "Interstitial water" is the term given to this water and is defined as that water coexisting in the pore space with the oil prior to exploitation. The term ''connate water" has often been used synonymously with this term; however, this can be true only by a specific definition since, geologically, it means the water in place at the time the rock structure was formed. The quantity of the interstitial water is a variable factor in any formation, since it depends on the hydrostatic forces present in any multiple-phase system. These forces may become unbalanced by the introduction of an extraneous force such as the raising or lowering of the "water table" or the migration of oil into a water-filled formation. Any unbalanced force results in a change in the interstitial water. There exists, however, an irreducible interstitial water. for a particular sand, that is the fraction of the pore space occupied by water when the capillary pressure at the particular point in question is at an equilibrium with the hydrostatic head of the oil sand in the reservoir. For this discussion the term "irreducible water saturation" will be used in place of "irreducible interstitial water saturation" for the sake of brevity; however, they are understood to be identical. A great amount of work has been devoted to the theory and methods for studying the irreducible water saturation and its related capillary pressure. As a result of the publications of Leverett;' Hassler, Brunner and Deahl;2 Calhoun and Lewis;3 and others, the role of capillary pressure studies is being accepted by the industry as a tool for studying suhsurface phenomena. Many techniques have been developed and published for determining the capillary pressure and irreducible water. In general, these techniques may be grouped into three classifications. One of the first was the capillary pressure method described by Leverett1 and expanded by Bruce and Welge.4 The experimental results were compared with water saturation of cores obtained using oil-base mud. Thornton and Marshall compared the irreducible water saturation of core samples determined by the capillary pressure method and by salinity and reported good agreement between the two methods. The second classification for determining the irreducible water and capillary pressure may be referred to as the "centrifugal force method." The general technique is similar to the capillary pressure method except that the force driving the reservoir fluid from the sample is of a centrifugal nature. A complete description of this method was presented by J. J. . McCullough and F. W. Albaugh.6 A process, the reverse of the capillary pressure method, was presented by W. R. Purcell.7 Mercury under pressure is driven into the pores of the rock and the saturation of the core determined at each applied pressure. The resulting capillary pressure curve is used to evaluate the irreducible water saturation. The techniques mentioned are singular in their approach to the irreducible water saturation. In all cases. an external force was applied to the core. The forces employed in the evaporation method are the vapor pressure of the liquid causing evaporation, the kinetic diffusion forces. adsorptive forces and. to a lesser degree, the viscous forces resisting flow to the surface. The basic definition of irreducible water is that water held in a state of equilibrium between capillary and hydrostatic forces This water has been described by previous investigators as being held in the microcapillaries too small to support fluid flow. Actually, this fluid volume is made up of the water in the microcapillaries and as a film adhering to the surface of the crystals. All capillaries. therefore, possess some liquid as a film, the thickness of the film being dependent on the properties of the fluid and solid. A discussion of experiments with references pertaining to the measurement of this immobile layer next to the solid surface can be found in the text by J. J. Bikerman.8 Eversole and Lahr calculated the thickness of this layer to be in the order of 10 ' to 10' cm for aqueous solutions and glass. Between two quartz surfaces they found the thickness to be 2 x 10 cm. The work of Volkova, on the capillary movement of water and toluene in quartz grains, indicated the thickness of the Immobile layers to be near 10' cm. Since any measurement is an average value, it is easy to understand that an absolute value would depend on the roughness of the surfaces involved and the complexity of the system. A calculated effective pore radius of 2 x 10 cm is obtained at the, irreducible saturation of a porous media in a water-air system when a capillary pressure of 100 psi is applied. Since the separation of the sand grains is of the same approximate magnitude as the immobile layer.

Jan 1, 1951

By W. A. Bruce

This paper presents the essentials of a mathematical method of studying the pressure behavior of an oil reservoir as the fluids are withdrawn. Methods are shown Whereby the behavior of a reservoir can be used to predict the future relationship between withdrawals and pressure. The oil reservoir is considered as a small part of a large porous continuum, which contains for the most part water. The expansion of this water resulting from a decrease of pressure in the oil zone causes a movement of water that is an important factor in the relationship between fluid withdrawals and reservoir pressure. Examples are given to illustrate the methods of pressure prediction for a circular reservoir containing undersaturated crude, the pressure distribution over a field that has a uniform production rate, the effect of a fault line near a field, the mutual interference of near-by fields, and the perturbing influence of a gas cap. Applications of the analysis to well-spacing problems are shown. Introduction The pressure-prediction methods to be described here are based upon the conception of an oil pool as a small part of a large porous continuum, containing for the most part water. The formation containing this water may be thought of as extending over an area of many square miles and having one or more small bodies of oil or gas trapped in high spots or reservoirs. It will be treated as having the genera1 aspect of a thin, flat sheet with an over-all tilt to the horizontal and with numerous small high spots, tight zones, and irregularities This porous continuum will be treated as being much more extensive than the oil or gas zones, but will be recognized as terminating at such large boundaries as a general fault, outcrop, unconformity, or pinch-out. Throughout the greater part of this limited porous continuum it is likely that there is a hydraulic connection. If this is true, the removal of fluid in one place will cause a disturbance that eventually will travel to all parts of the continuum. This picture has led to the recognition of water as the major fluid in the porous continuum and in many cases the expansive nature of this water as the main driving force producing the oil. The next step is the solution of the general problem of compressible liquid behavior in porous media. The works of Hurst I and Muskat2 introduced the idea of using heat-flow mathematics to consider the problem of compressible liquid flow in a porous medium. Before their reports, it had been thought sufficient to use the incompressible fluid-flow work of S1ichter.3 Law Muskat4 pointed out in detail how far the incompressible-fluirl assumption, deviated from fact even for water, of which the compressibility is about 3 X 10-6 volumes per unit volume per pound per square inch. He showed that this deviation increased with increases of distance. For example, the incompressible-fluid formula might show good agreement with the

Jan 1, 1943

By W. A. Bruce

This paper presents the essentials of a mathematical method of studying the pressure behavior of an oil reservoir as the fluids are withdrawn. Methods are shown Whereby the behavior of a reservoir can be used to predict the future relationship between withdrawals and pressure. The oil reservoir is considered as a small part of a large porous continuum, which contains for the most part water. The expansion of this water resulting from a decrease of pressure in the oil zone causes a movement of water that is an important factor in the relationship between fluid withdrawals and reservoir pressure. Examples are given to illustrate the methods of pressure prediction for a circular reservoir containing undersaturated crude, the pressure distribution over a field that has a uniform production rate, the effect of a fault line near a field, the mutual interference of near-by fields, and the perturbing influence of a gas cap. Applications of the analysis to well-spacing problems are shown. Introduction The pressure-prediction methods to be described here are based upon the conception of an oil pool as a small part of a large porous continuum, containing for the most part water. The formation containing this water may be thought of as extending over an area of many square miles and having one or more small bodies of oil or gas trapped in high spots or reservoirs. It will be treated as having the genera1 aspect of a thin, flat sheet with an over-all tilt to the horizontal and with numerous small high spots, tight zones, and irregularities This porous continuum will be treated as being much more extensive than the oil or gas zones, but will be recognized as terminating at such large boundaries as a general fault, outcrop, unconformity, or pinch-out. Throughout the greater part of this limited porous continuum it is likely that there is a hydraulic connection. If this is true, the removal of fluid in one place will cause a disturbance that eventually will travel to all parts of the continuum. This picture has led to the recognition of water as the major fluid in the porous continuum and in many cases the expansive nature of this water as the main driving force producing the oil. The next step is the solution of the general problem of compressible liquid behavior in porous media. The works of Hurst I and Muskat2 introduced the idea of using heat-flow mathematics to consider the problem of compressible liquid flow in a porous medium. Before their reports, it had been thought sufficient to use the incompressible fluid-flow work of S1ichter.3 Law Muskat4 pointed out in detail how far the incompressible-fluirl assumption, deviated from fact even for water, of which the compressibility is about 3 X 10-6 volumes per unit volume per pound per square inch. He showed that this deviation increased with increases of distance. For example, the incompressible-fluid formula might show good agreement with the

Jan 1, 1943

By T. T. Read

JAPAN'S iron and steel industry has always been closely connected with military strategy. Many years ago it became evident that the country's iron-ore resources were too small to support any extensive industry. As a result a belief in the imperative necessity of securing such resources has influenced Japan's political and economic policy in the Far East. Iron-ore developments in China are too well known to need repeating except to note that they have been rather unsatisfactory to both China and Japan. The ore deposit at Tayeh, in China, is not as large as was first believed and, though that and other sources of supply in China proper are now furnishing Japan a little more than a million tons of ore yearly, it cannot be counted upon as a large permanent source of supply. The deposit in Shantung proved so disappointing on further exploration that operations there have, so far as I know, long since ended. The operations at Pen-bsi-hu, in South Manchuria, which C. F. Wang de¬scribed in the A.I.M.E. TRANSACTIONS for 1918, Vol. 59, were reported to have yielded 84,000 tons of pig iron in 1928 and about 50,000 in 1935, so they seem to be going back.

Jan 1, 1937