Search Documents

By K. R. Van Horn, L. W. Kempf

Plastic deformation of most commercia1 metals within a sufficiently low temperature range results in profound changes in structure and properties, of which the causes and effects are not completely understood. One of these effects is the presence of internal residual stresses and strains, which ordinarily do not appear to require specific consideration in most structural applications but which may be quite undesirable in particular instances. For example, in heavy sections that require considerable machining before assembly, residual stresses may be undesirable because of the distortion they cause when their balance is disturbed by machining or otherwise. In addition, the distribution of stresses may be such that it acts in the same direction as the applied load, thus bringing about premature failure or reducing the load-carrying capacity of the member. One source of residual stress in metal structures is the plastic deformation that may occur during rapid cooling from relatively elevated temperatures, as in the cooling of a casting in the mold or the quenching of a heavy section from elevated temperatures during heat-treatment. These residual stresses are usually undesirable because their direction of operation and magnitude cannot be controlled well enough to permit utilization of the changes in properties of the metal that they may bring about. The most convenient manner of controlling such residual stress is by proper selection of the cooling rate or by reheating to a temperature at which plastic flow can take place, resulting in relief of the residual stresses and strains. Both of these methods of control, however, may cause a reduction in the optimum properties obtainable from the previous operation. A compromise must be struck, and if it is to result in the best possible combinations of properties, specific information must be available regarding the magnitude of the stresses and the rate at which they are affected by variations in cooling rate or in reheating temperature. The complete quantitative estimation of residual stress in complicated metal shapes is exceedingly difficult, if not impossible. In simple sections, however, relatively quantitative analysis may be applied and useful cstimations of stress distribution may be made. This paper is concerned largely with the rate of relief, upon reheating, of internal residual stress in simple aluminum-alloy structures. Since even with simple structures quantitative estimation of residual stresses is laborious and costly, an attempt was made to find other means of collecting data upon which commercial heat-treatments might be based. Incidentally, a few data were collected bearing on the problem of relaxation of aluminum alloys. Determination of Residual Stresses The magnitude and distribution of residual stresses in simple aluminum-alloy shapes rapidly cooled from elevated temperatures has been discussed in a previous paper.' Fig. I reproduces some of the data

Jan 1, 1942

By L. W. Kempf, K. R. VanHorn

PLASTIC deformation of most commercial metals within a sufficiently low temperature range results in profound changes in structure and properties, of which the causes and effects are not completely understood. One of these effects is the presence of internal residual stresses and strains, which ordinarily do not appear to require specific consideration in most structural applications but which may be quite undesirable in particular instances. For example, in heavy sections that require considerable machining before assembly, residual stresses may be undesirable because of the distortion they cause when their balance is disturbed by machining or otherwise. In addition, the distribution of stresses may be such that it acts in the same direction as the applied load, thus bringing about premature failure or reducing the load-carrying capacity of the member. One source of residual stress in metal structures is the plastic deformation that may occur during rapid cooling from relatively elevated temperatures, as in the cooling of a casting in the mold or the quenching of a heavy section from elevated temperatures during heat-treatment. These residual stresses are usually undesirable because their direction of operation and magnitude cannot be controlled well enough to permit utilization of the changes in properties of the metal that they may bring about. The most convenient manner of controlling such residual stress is by proper selection of the cooling rate or by reheating to a temperature at which plastic flow can take place, resulting in relief of the residual stresses and strains. Both of these methods of control, however, may cause a reduction in the optimum properties obtainable from the previous operation compromise must be struck, and if it is to result in the best possible combinations of properties, specific information must be available regarding the magnitude of the stresses and the rate at which they are affected by variations in cooling rate or in reheating temperature. The complete quantitative estimation of residual stress in complicated metal shapes is exceedingly difficult, if not impossible. In simple sections, however, relatively quantitative analysis may be applied and useful estimations of stress distribution may be made. This paper is concerned largely with the rate of relief, upon reheating, of internal residual stress in simple aluminum-alloy structures. Since even with simple structures quantitative estimation of residual stresses is laborious and costly, an attempt was made to find other means of collecting data upon which commercial heat-treatments might be based. Incidentally, a few data were collected bearing on the problem of relaxation of aluminum alloys. DETERMINATION OF RESIDUAL STRESSES The magnitude and distribution of residual stresses in simple aluminum-alloy shapes rapidly cooled from elevated temperatures has been discussed in a previous paper.1 Fig. I reproduces some of the data

Jan 1, 1941

By L. W. Kempf, K. R. Van Horn

Plastic deformation of most commercia1 metals within a sufficiently low temperature range results in profound changes in structure and properties, of which the causes and effects are not completely understood. One of these effects is the presence of internal residual stresses and strains, which ordinarily do not appear to require specific consideration in most structural applications but which may be quite undesirable in particular instances. For example, in heavy sections that require considerable machining before assembly, residual stresses may be undesirable because of the distortion they cause when their balance is disturbed by machining or otherwise. In addition, the distribution of stresses may be such that it acts in the same direction as the applied load, thus bringing about premature failure or reducing the load-carrying capacity of the member. One source of residual stress in metal structures is the plastic deformation that may occur during rapid cooling from relatively elevated temperatures, as in the cooling of a casting in the mold or the quenching of a heavy section from elevated temperatures during heat-treatment. These residual stresses are usually undesirable because their direction of operation and magnitude cannot be controlled well enough to permit utilization of the changes in properties of the metal that they may bring about. The most convenient manner of controlling such residual stress is by proper selection of the cooling rate or by reheating to a temperature at which plastic flow can take place, resulting in relief of the residual stresses and strains. Both of these methods of control, however, may cause a reduction in the optimum properties obtainable from the previous operation. A compromise must be struck, and if it is to result in the best possible combinations of properties, specific information must be available regarding the magnitude of the stresses and the rate at which they are affected by variations in cooling rate or in reheating temperature. The complete quantitative estimation of residual stress in complicated metal shapes is exceedingly difficult, if not impossible. In simple sections, however, relatively quantitative analysis may be applied and useful cstimations of stress distribution may be made. This paper is concerned largely with the rate of relief, upon reheating, of internal residual stress in simple aluminum-alloy structures. Since even with simple structures quantitative estimation of residual stresses is laborious and costly, an attempt was made to find other means of collecting data upon which commercial heat-treatments might be based. Incidentally, a few data were collected bearing on the problem of relaxation of aluminum alloys. Determination of Residual Stresses The magnitude and distribution of residual stresses in simple aluminum-alloy shapes rapidly cooled from elevated temperatures has been discussed in a previous paper.' Fig. I reproduces some of the data

Jan 1, 1942

By S. E. Bretherton

Most metallurgists appreciate the great need of a process for the extraction and recovery of valuable metals from complex ore, where the presence of one metal increases the cost of extracting the other rnetals to such an extent that not any of the metals can be extracted at a profit. We need only refer to some of the mines in Colorado, Utah, and New Mexico, where oxidation has taken place and the sulphur, zinc, copper, and some of the iron and other metals have been leached out, large bodies of oxidized ore remaining, rich in lead, silver, and sometimes gold. These metals have been concentrated by the removal of the other metals, leaving a very desirable ore for treatment in the blast-furnace for the production of lead bullion, and recovery of the silver and gold. If lead is not present, the gold and silver metals are usually recovered by some method of milling, or the ore is shipped to a smelter, where it is mixed with lead ore or copper-iron sulphide ore from some other mine. In these same mines, when developed to greater depth below the leached or oxidized zone, the ore is found to contain the original mixture of sulphur, zinc, copper, etc., added to, or I should say left with, the lead, silver, and gold values; but instead of adding to the value of the ore, the presence of these elements, especially zinc, makes the copper, silver, and gold of less value, and often worthlees. Such was the experience of the oldest mines in Leadville,.Colo., until methods of mechanical separation of the lead from the zinc were developed sufficiently to allow of some profit by the making of a concentrate rich in zinc to be shipped to the zinc smelter, and sometimes a lead concentrate which could be shipped to the lead smelter; but even in these cases the waste of the different metals is a very serious matter. In the very best concentrating plants some zinc will be left in the lead concentrate, to be lost and to give considerable trouble in the lead-smelting furnace. On the other hand, some of the lead, with a large percentage of the copper and silver, will follow the zinc into the zinc concentrate, to be, perhaps, recovered by smelting the cinder or clinker left in the re-

Jan 1, 1915

By S. E. Bretherton

MOST metallurgists appreciate the great need of a process for the extraction and recovery of valuable metals from complex ore, where the presence of one metal increases the cost of extracting the other metals to such an extent that not any of the metals can be extracted at a profit. We need only refer to some of the mines in Colorado, Utah, and New Mexico, where oxidation has taken place and the sulphur, zinc, copper, and some of the iron and other metals have been leached out, large bodies of oxidized ore remaining, rich in lead, silver, and sometimes gold. These metals have been concentrated by the removal of the other metals, leaving a very desirable ore for treatment in the blast-furnace for the production of lead bullion, and recovery of the silver and gold. If lead is not present, the gold and silver are usually recovered by some method of milling, or the ore is shipped to a smelter, where it is mixed with lead ore or copper-iron sulphide ore from some other mine. In these same mines, when developed to greater depth below the leached or oxidized zone, the ore is found to contain the original mixture of sulphur, zinc, copper, etc., added to, or I should say left with, the lead, silver, and gold values; but instead of adding to the value of the ore, the presence of these elements, especially zinc, makes the copper, silver, and gold of less value, and often worthless. Such was the experience of the oldest mines in Leadville, Colo., until methods of mechanical separation of the lead from the zinc were developed sufficiently to allow of some profit by the making of a concentrate rich in zinc to be shipped to the zinc smelter, and sometimes a lead concentrate which could be shipped to the lead smelter; but even in these cases the waste of the different metals is a very serious matter. In the very best concentrating plants some zinc will be left in the lead concentrate, to be lost and to give considerable trouble in the lead-smelting furnace. On the other hand, some of the lead, with a large percentage of the copper and silver, will follow the zinc into the zinc concentrate, to be, perhaps, recovered y smelting the cinder or clinker left in the re-

Jan 7, 1914

By J. B. Hess, R. L. Dietrich

IN the mechanical twinning of magnesium on the {1012} planes the crystallographic deformation is such that, in the direction of the hexagonal axis [0001], twinning is possible only under tension stress, while in the directions perpendicular to the hexagonal axis, twinning is possible only under applied compression. Thus in extruded magnesium and magnesium alloys where the extruded textures are best described as either [1010] or [ 1120] fibers,1 the basal planes are all nearly parallel to the extrusion axis and such material is susceptible to {1012 } twinning by compression in the direction of the extrusion axis. In order to explain the results of cyclic stressing in alternate tension and compression upon the tangent elastic modulus in such material, Dorn and Thomsen2 have postulated that, following twinning under applied compression, a retwinning or untwinning occurs as a result of residual microtensile stresses immediately upon removal of the applied compressive force. Recently, Carapella and Shaw3,4 have used this supposition of untwinning in magnesium in discussing their results on indentation hardness and on cold drawing of MI sheet. In trying to confirm this hypothesis by suitable direct experiments, the authors have been unsuccessful in detecting any evidence whatsoever that untwinning follows the release of applied compression and are forced to conclude that this hypothesis is improbable or, at least, that the quantity of material involved is small. For the experiments, small cylindrical specimens 0.040-in. diam. X 0.120- to 0.140-in. long were etched from 0.0625-in. extruded rod. The ends of the specimens were accurately faced off parallel in a jeweler's lathe. The compression jig was simply an ordinary set of micrometer calipers with an anvil interposed between the spindle and the specimen. The anvil was free to move axially but restrained from rotating so that the rotation of the spindle would not introduce a twisting stress on the specimen. With this arrangement the compressive strains could be estimated to 0.0001 in. and X ray pinhole photographs could be taken with or without load as required. Fig 1 is the pattern of an uncompressed specimen of AZ31 alloy, showing the approximate [1010] extrusion fiber. The X ray beam is normal to the extrusion axis; in this position it is particularly sensitive in detecting twinning if one directs his attention to the diffraction ring from the basal plane. Since twinning on {1012} planes produced an 86° reorientation of the crystal lattice, the original basal reflections occur at the 3 and 9 o'clock positions while the (0002) reflections from any twinned material will occur at the 6 and 12 o'clock positions. Fig 2 shows the same specimen compressed 3.0 pct, photographed while still under load. This strain has been just enough to produce a detectible amount of twinning and the sensitivity is roughly indicated by the fact that no alterations were produced in the intensities or maxima of the other diffraction rings. A strain of

Jan 1, 1948

By A. J. Weinig

THE Liberty Bell cyanide precipitate is unique in that it is apt to vary widely in composition in the course of very short, periods of time, and a method of refining and melting that would prove highly satisfactory at one cleanup would yield almost an hopeless "mess" it a second. Table I gives a general conception of the wide range in grade and composition of those raw precipitates. It is evident that no one standard flux could be expected to produce a high-grade bullion with such a widely variable precipitate, and that any method of treatment with acid requires most careful consideration. Refining by Acids Naturally, our first efforts to improve our precipitates were directed along the lines of acid treatment. Table II embodies the results of careful sampling and analysis of one cleanup at the time when wet refining reached its maximum development at this mill. We have now discarded all methods of wet refining, successfully replacing them by amore scientific method of flux calculation described herein, but it is believed that a general description of this wet refining is warranted as it throws some interesting side lights on acid refining in general.

Jan 3, 1916

By D. H. Newland

New York has a small but not insignificant place in the oil and natural gas industries of the United States. It has had a continuous record as an oil producer since 1872, with an aggregate yield of about 104,000,000 bbl. The reported output for 1935 was 4,237,000 bbl., a gain of more than 10 per cent for the year and a total that has been exceeded only in the early period of flush production half a century ago. The industry has been steadily building up since 1920 with the successful practice of the water drive, which has given a new lease of life to pools that had been practically drained of oil recoverable by pumping. An additional output of 2000 bbl. or more per acre is being procured by this method. Altogether the fields in New York State cover about 55,000 acres. Their limits are well defined and it is unlikely that they will be extended in the future, although there is some prospect of finding additional supplies by deeper drilling. The oil from New York is all classed as Pennsylvania grade, for which the recent price has been about $2.50 a barrel. It is refined at Olean, Wellsville and Bolivar, in the oil district, and partly in Pennsylvania refineries. Exploration for natural gas, outside of the established districts, was considerable during the year. Altogether 59 wells were drilled, distributed over 13 counties, of which 33 were listed as producers and 26 were dry. At the close of the year, 13 wells were in process of drilling. The 33 producing wells had a combined estimated flow of 278 million cubic feet per day. The best results were obtained from exploration in Allegany County, where out of eight wells drilled to the Oriskany sandstone five were successful and showed a combined open-flow capacity of 107 million cubic feet. The Oriskany sandstone was encountered at a depth of 4500 to 4900 ft. In Steuben County, next east of Allegany County, two out of seven wells to the Oriskany proved productive, and one of these, in the town of Greenwood, on the Watkins structure, was probably the largest that has so far been opened in the state, with a reported yield of 35 million a day. In the central part of New York interest was awakened by the activity shown in exploring for gas in the Trenton limestone, in Camden, Florence and Rome townships, Oneida

Jan 1, 1936

By D. H. Newland

New York has a small but not insignificant place in the oil and natural gas industries of the United States. It has had a continuous record as an oil producer since 1872, with an aggregate yield of about 104,000,000 bbl. The reported output for 1935 was 4,237,000 bbl., a gain of more than 10 per cent for the year and a total that has been exceeded only in the early period of flush production half a century ago. The industry has been steadily building up since 1920 with the successful practice of the water drive, which has given a new lease of life to pools that had been practically drained of oil recoverable by pumping. An additional output of 2000 bbl. or more per acre is being procured by this method. Altogether the fields in New York State cover about 55,000 acres. Their limits are well defined and it is unlikely that they will be extended in the future, although there is some prospect of finding additional supplies by deeper drilling. The oil from New York is all classed as Pennsylvania grade, for which the recent price has been about $2.50 a barrel. It is refined at Olean, Wellsville and Bolivar, in the oil district, and partly in Pennsylvania refineries. Exploration for natural gas, outside of the established districts, was considerable during the year. Altogether 59 wells were drilled, distributed over 13 counties, of which 33 were listed as producers and 26 were dry. At the close of the year, 13 wells were in process of drilling. The 33 producing wells had a combined estimated flow of 278 million cubic feet per day. The best results were obtained from exploration in Allegany County, where out of eight wells drilled to the Oriskany sandstone five were successful and showed a combined open-flow capacity of 107 million cubic feet. The Oriskany sandstone was encountered at a depth of 4500 to 4900 ft. In Steuben County, next east of Allegany County, two out of seven wells to the Oriskany proved productive, and one of these, in the town of Greenwood, on the Watkins structure, was probably the largest that has so far been opened in the state, with a reported yield of 35 million a day. In the central part of New York interest was awakened by the activity shown in exploring for gas in the Trenton limestone, in Camden, Florence and Rome townships, Oneida

Jan 1, 1936

By C. E. Shoenfelt, D. E. Winchester

NO important discoveries of petroleum during 1933 were reported from New Mexico. Lea and Eddy counties were the centers of activity during the drilling season and each had a number of interesting completions. The Hobbs pool, in Lea County, was definitely outlined on the east, north and northwest. Under an agreement reached last summer by state officials and operators, the Hobbs pool was continued under proration throughout the year. One hundred eighty-four units of 40 acres each were being produced at the end of 1933. The allowable was 21,306 bbl. daily at the beginning of 1933, but when the agreement was revised in the spring the minimum was raised to 30,000 bbl., and by the end of the year had been raised to 33,473 bbl. At present the field is being prorated on the basis of 25 per cent on acreage and 75 per cent on potentials except in the southwestern edge of the field, where water encroachment is a problem. In this area the basis of proration is 40 per cent on acreage and 60 per cent on potentials. A corrective method employed in this part of the field has been partly successful. The water is advancing in the upper part of the pay, a dolomitic limestone, and in a number of instances packers have been set in the pay below the water and above the oil. The locating of a satisfactory seat for a packer is difficult and in some instances has not been a complete success. Pipe line runs from the field during the year aggregated 11,413,218 bbl., bringing the total gross production up to 41,093,681 bbl., of which 39,000,-000 bbl. has been produced under proration, which went into effect on July 10, 1930. On Nov. 30, potentials were determined on the assigned pressure basis and the total was reduced 71,165 bbl. daily, to 1,265,-332 barrels. The outstanding completions in the Hobbs pool were three in number, of which the best was the Humble Oil & Refining Company's No. 3B Bowers in sec. 20, 18S., 38E., with an initial production of 11,664 bbl. of oil and 10,000,000 cu. ft. of gas. The Shell Petroleum Company's No. 4B McKinley, in the same section, produced at the rate of 22,940 bbl. of oil while flowing open, but when tubed, flowed at the rate of 6610 bbl. The third outstanding well, No. 4 Hardin of the Tidal Oil Co., and located in

Jan 1, 1934

By Edwin F. Brush, John Chipman

Published data on the activity of carbon in binary and ternary austenite at 1000°C are reviewed. The composition variables are . The coefficient, Vj, has the value for substitutional elements but may be assigned a ualue -1 for silicon to effect a simplification on the mathematical treatment. The activity coefficient PC = is obtained from gas equilibrium data. For the ternary systems studied the Henrian activity coefficient is given by the expression: The principle advantage in cornparison with the analogous expression in terms of atom fractions is found in the fact that for most systems the final term and in many the last two terms are zero. Values of the interaction parameters are tabulated and the graphical comparison of the equation with experirt~ental data is sho,wn in several figures. The thermodynamic properties of the solid solution, austenite, are of considerable importance in the heat-treatment of alloy steels and in other aspects of ferrous metallurgy. Early studies embodied in the Fe-C diagram have been extended to include other binary and some ternary diagrams. Our best hope of obtaining a useful thermodynamic treatment of reactions in complex alloy steels will not be found in quaternary and quinternary phase diagrams but in determinations of activities and interaction relations among the several solute elements. The foundation for such a development was laid by smith' in his early studies of the activity of carbon in Fe-C alloys and his subsequent work on Fe-C-Si, Fe-C-Mn, Fe-C-Ni, and Fe-C-Co solid solutions.2"4 Other observers have also made noteworthy contributions and these will be discussed and correlated here in the light of a somewhat simplified mathematical treatment of solute interactions. Fe-C AT 1000°C In a recent review of the thermodynamic properties of binary Fe-C austenite it was shown that the simple mathematical treatment employed by smith' was capable of describing all the published results on this solution. The treatment utilizes the atom ratio, yc = nC/nF,, rather than the atom fraction. The activity of carbon is proportional to the equilibrium gas ratio, either measured on a scalk in which the activity of graphite is taken as unity or, alternatively, aC may be set equal to yc at infinite dilution. In either case the ratio aC/y = (PC, the activity coefficient. It was found that the experimental data of smith1 and those of Diin-wald and wagner; Bungardt, Preisendanz, and Lehn-ert,' and Scheil, Schmidt, and Wiinnings at temperatures of 800" to 1200° C as well as reliable data on the solubilities of graphite and cementite could be represented by the equation for which graphite is the standard state: The data on alloyed austenite have been obtained at 1000°C. For this temperature, the "Henrian" activity coefficient (which is unity at infinite dilution) is: FOr an interstitial solute such as carbon in austenite it has been shown by statistical mechanicsg that the activity in the infinitely dilute solution is proportional to the ratio of the number of lattice sites occupied by carbon to the number of yet unfilled lattice sites. A variable zz proportional to this ratio serves as a useful measure of concentration:" in which b is the number of lattice sites provided by each atom of solvent; in austenite b = 1. The Henrian activity approaches zz at infinite dilution and the ratio a is the activity coefficient. The effect of a change in concentration is then given by: It has been shown further that in some systems the derivative in Eq. [4] remains constant over a wide range of concentrations. In such a case second-order terms become negligible and the Henrian activity coefficients is:

Jan 1, 1969

By S. Harries Daddow

THE INSUFFICIENCY OF PILLARS OF COAL FOR THE PURPOSES DESIGNED-THE FRUITFUL CAUSE OF DANGER, EXPENSE, AND WASTE-THE PROOF OF INSECURITY-SUBSTITUTE FOR PILLARS OF COAL-PILLARS AND PANELS COMPARED. PILLARS of coal, which are designed and left in our mines as the means of supporting the overlying strata of our coal-beds, and securing protection to the miner, are not only insufficient for these purposes, but the most objectionable means of providing the desired security to life and property. Though such pillars are left at a great sacrifice to the owners of collieries and mineral lands, loss to the resources of the commonwealth, and ultimate privation to the public, they defeat the very ends for which they are designed, and not only do not secure life and property, but are as fatal to the one as ruinous to the other. Propositions.-It is eminently desirable that the resources of the commonwealth-particularly our mineral wealth in anthracite coal, which is limited-should be carefully utilized and made available, not only to ourselves but our posterity. Yet, speaking as an anthracite miner, we are wasting our resources of coal with a recklessness which will bring ruin in the end, unless checked, not only to the iron manufacturing interests of the East, whose chief protection, in competition with the iron-masters of the interior, lies in a cheap and abundant supply of anthracite furnace fuel, but to the best interests of the State. It is, consequently, not only desirable, but necessary, that we should realize every ton of coal from each colliery, and every acre of coal area, in order that our resources may not be wasted at present, to breed want in the future, and to realize the greatest present benefit to the mine, the miner, and the public. It is not possible, however, to secure these ends, if we continue to leave, as we do at present, from one-third to one-half our resources in anthracite as pillars in our mines. But our sad bills of mortality, our abandoned collieries, and our yawning mountain-sides, present ample evidence that even this enormous waste of coal, though left for the purpose of protecting life and property, is as totally inade-

Jan 1, 1873

By Cecil Desch

THIS annual lecture, under the auspices of the Institute of Metals Division, and which was illus- trated by lantern slides, has been printed in full and a limited number are available for distribution on request. Some excerpts from the lecture are given below: Ever since the simple geometrical relations of crystals were discovered, it has been recognized that their proper-ties are best explained by assuming that their ultimate particles are arranged on a space lattice, and that the char-acteristics of that lattice determine the shape of the crystal and its physical and mechanical properties. Modern ex-amination by means of X-rays has widened that concep-tion and given it greater; definiteness, and the atoms are now regarded as the particles forming the space lattice. The splendid achievements of investigators in this field have made it possible to state, for a large number of sub-stances, the form and dimensions of the lattice. The char-acteristic of a lattice is that a unit of simple geometrical form is repeated at regular intervals in three dimensions so as to fill the entire crystal. It follows that there must be certain planes in which the atoms are more closely packed than in planes drawn at any angle to them, and it is these planes of closest packing which play the greatest part in determining the growth and other properties of the crystal. There are actually two stages in crystallization, what-ever be the medium in which it occurs. The first is the ap-pearance of crystal nuclei; the second the growth of those nuclei to form crystals of appreciable .size. The first is clearly a kinetic phenomenon. In the molten mass, solu-tion, or vapor, the molecules are in a state of rapid motion and frequent collision. When the temperature has fallen so far. that it is possible for a crystal to exist, a few col-liding molecules may fail to rebound, and so become at-tached to one another, the balance between the attracting and repelling forces-between them causing them to arrange themselves on a space lattice, to which other molecules sub-sequently attach themselves. It was once maintained that the X-ray evidence demanded that the molecule should dis-appear in the solid crystal, but this was a wrong inference, and in many crystals, but not in all, the chemical molecule retains its identity in the solid state. In pure metals the atom and the molecule are identical, so that the conditions are unusually simple. How many. nuclei will be formed in a given mass is evi-dently a problem in probability. Experiments to deter-mine the relation between the temperature and the number of nuclei formed in a given time have been made with some success by using viscous organic substances, but metals offer much greater difficulties, and the few determinations which have been published are vitiated by serious errors. However, the examination of sections of ingots of the same composition and cast at 'the same temperature in similar molds will show, that the number of crystals does not vary widely.

Jan 3, 1927

By A. E. Bellis

There is a wide difference of opinion among rifle experts in the matter of barrel steel, and the relative importance to the life of the barrel of the steel's composition, heat treatment, structure, and physical properties. In order to promote discussion, which it is hoped may' lead to the discovery of the source of some of the traditional beliefs on the subject, the results of some tests are presented here, with data on heat treating, physical tests, and erosion. The detailed metallographic study of this steel is given in another paper.l The conclusions from these tests should be capable of wider application than their direct bearing on the barrel-steel problem. The Government specifications for barrel steel for model 1903 rifle (Springfield) call for carbon 0.50 to 0.60 per cent., manganese 1.00 to 1.29 per cent., silicon under 0.25 per cent., sulfur under 0.06 per cent., phosphorus under 0.08 per cent. The minimum physical requirements are: Tensile strength, 110,000 lb. per sq. in. (7733 kg. per sq. cm.); yield point, 75,000 lb. per sq. in (5472 kg. per sq. cm.); elongation, 20 per cent.; reduction of area, 45 per cent. Material fulfilling these requirements gives practically no failures when proof-fired, with charge of 70,000 lb. per sq. in. pressure, which is 40 per cent. in excess of the service charge. The turning and drilling operations show up any seams or laps such as accidentally occur even in the best heats of open-hearth steel, so that faulty stock is practically all eliminated before proof-firing. These physical requirements are met either by rolling billets at a proper temperature down to the form of tapered barrel blanks or by heat treating bars that have been upset to cnlarge the breech section. The transformation temperature of this steel, on heating, is around 1350" F. (732' C.), varying somewhat with the composition and the rate of heating. The actual treatment of the barrel blanks, as carried out by different manufacturers, gives four kinds of barrels, which will be called A, B, C, and D, for convenience. A barrels result from heat treating upset blanks by quenching at

Jan 1, 1920

By J. W. Richards

Plating iron with copper has received great attention from practical and scientific men, but, aside from the deposit secured by immersion of iron in copper salts, by electro-plating, or by welding together thin sheets of iron and copper, these efforts have met with no success. Failure of these efforts, in the production of copper plating, has been due to the fact that the conditions normally and necessarily present in the plating operation are antagonistic to the production of copper-plated iron. In most, if not quite all of them, a bath of molten copper has been used. The temperature of a molten copper bath is so high that the iron becomes oxidized before it can be immersed in the molten copper, and unless a protective flux for the molten copper is used, the surface of the copper will become oxidized, and, in any event, the plated iron will oxidize immediately on its being withdrawn from the molten bath. I recently had the pleasure of visiting the works of The Metals Plating Co. at Elizabeth, N. J., where I witnessed the plating of iron sheets with copper by a new process.l The plating metal is applied to the sheet in the form of a liquid mixture by means of rolls, such as inking rolls. The sheet, after being coated with the mixture, is automatically carried forward and deposited on a link-belt conveyor, which carries it through a furnace maintained at a temperature well above that of molten copper. The basic principle involved in this method lies in the application of the plating metal to the sheet while the sheet is cold and then melting the metal in place on the sheet under conditions which are favorable to the formation of the plating. Plating Mixture The liquid plating mixture is composed of either copper oxide or finely divided copper, or a mixture of both, ground to the consistency of a light varnish in a crude oil having an asphaltic base, of a specific gravity of from 14" to 16' Be. The plating mixture which gives the best results

Jan 1, 1919

By AIME AIME

MINING men in general- are a roving lot but not so Selwyn G. Blaylock. Immediately after graduation from McGill in 1899 he went to the Trail smelter and he is there today though he spent three or four years of his early professional life at other British Columbia mining centers. Either he sensed the great possibilities of the company of which he is now vice-president and general manager, or it sensed his; more probably both. Certainly the association was a happy and fortunate one.

Jan 1, 1937

By Grover J. Holt

IN order to provide a clear picture of the development of the sink-and-float process of concentration as applied to the iron ores of Minnesota, a few pertinent facts should be brought out concerning the ores and the products of concentration. Iron ore is primarily a cheap commodity handled in immense quantities. The price of iron ore at present, based on a natural iron content of 51.5 per cent, varies from $2.55 to $2.70 per gross ton f.o.b. cars at the mine or washing plant in Minnesota. Last year 92,000,000 gross tons were shipped from the Lake Superior district (Minnesota, Michigan, and Wisconsin) to the furnaces. Concentrated iron ores have no greater value per unit of iron content than ores that can be mined and shipped direct from the shafts or open pits. For years only the higher grades of concentrating ores could be treated and sold in competition with the immense reserves of direct shipping ore available. These higher-grade "straight wash" ores required only the simplest treatment; namely, the washing out of fine sand from coarse ore particles. As the exhaustion of the "straight wash" ore is reached, rock is found replacing part of this sand, and the ore no longer responds to the former sizing treatment. Substantial tonnages of this marginal (jig ore) remained to be treated. Because of the limitations placed on concentrates by the furnaces-namely, low price of product and minimum amount of fines-iron-ore concentration has been and must continue to be a one-pass process. Only an increase in price or a change in structure of concentrates allowed by the ore consumer will encourage departure from this practice. Faced with the necessity of handling large tonnages, with the limitations mentioned, iron-ore research men have found their search for new and more efficient methods of treatment seriously handicapped and removed from the field of fine crushing. Sink-and-float treatment appeared to offer the best field in coarse concentration and has been proved by several plants to be well adapted to our problem. The use of ferrosilicon as a medium solid was decided upon. In our present practice, the ferrosilicon metal, carrying about 83 per cent iron, 15 per cent silicon and 2 per cent carbon and nonmagnetics, is crushed to pass 65 mesh and used without further sizing. When mixed with water the specific gravity of the medium may be controlled to within 0.02 per cent above or below the required gravity. Table I shows examples of a change in solid content of the medium for varying gravities. [ ] Table I is based on clean ferrosilicon, whereas some contamination is always present in the mill circuit, tending to

Jan 1, 1943

Discussion of the paper of WALTHER MATHESIUS, presented at the New York meeting, February, 1915, and printed in Bulletin No. 99, March, 1915, pp. 539 to 555. JOSEPH W. RICHARDS, So. Bethlehem, Pa.-This paper answers. partly the difficult questions which have come up as to why it is not economical to use higher blast temperatures in the smelting of Mesaba ores, such as the high temperatures used in European practices, and the answer is very plain that the ores will not stand the higher temperature. But the paper does not go into detail as to what special difficulties were found with the higher temperature of blast, and I would ask the author to kindly specify them. W. A. FORBES, New York, N. Y.-A large part of the troubles that furnace men experienced in using high-blast heats in smelting Mesaba ores in the early days of using Mesaba ores, was clue to the attempt to use these soft ores on furnaces having the same lines as the furnaces used in smelting the hard Old Range ores. As the result of observation and study, the dimensions of the lower part of the blast furnaces have been changed and the difficulties of the blast-furnace men in operating with a large percentage of Mesaba ore and high-blast temperatures have been largely overcome. The changes I refer to in particular are: (1) steepening the angle of the bosh; (2), decreasing the height of the bosh; (3) increasing the diameter of the hearth. JOSEPH W. RICHARDS.-Mr. Forbes's answer is quite satisfactory, and the moral which it points is that when the furnace is run with a higher temperature in the smelting zone, the furnace lines which were adapted for the lower temperatures are not necessarily those best suited for the higher hearth temperatures. If. enriched blast were used in a furnace, and higher temperatures run, it would be found necessary to further modify the lines of the furnace to meet the new conditions and to get the maximum output with economy. J. E. JOHNSON, JR., New York, N. Y.-It seems to me this is one of the few papers which could well have been a little longer. The data which Mr. Mathesius has given us, I think should be considered in connection with the paper which Mr. Brassert read before the American Iron and Steel Institute last spring, in which he described how they had obtained remarkable results with furnaces with steep but very short boshes; the angles have been raised to 80°, and the boshes made so short that they no longer appear as a conspicuous part of the shape of the furnace.

Jan 5, 1915

By C. B. Scotty, E. F. Egan

INTRODUCTION The neutron-garnma log has been used for stratigraphic correlation by the oil industry for a number of years. In the past few years, the quantitative application of the log to provide information with respect to porosity has received considerable attention. The basic concept of quantitative interpretation has been pointed out in the literature.1 It shall be the purpose of this paper to develop by empirical means a method whereby the relationship of porosity to neu. tron-gamma deflection may be predicted for various bore hole diameters. This relationship is applicable to the present commercially available neutron-gamma log run in open hole. Data available at present are insufficient to establish similar correlations for cased holes. Through the development of such a correlation, the importance of the various factors which influence the log become evident. NEUTRON-GAMMA CURVE The logging tool conisists of a source of neutrons and a means of detecting and measuring gamma rays, the detector being shielded from the direct emission from the source. The gamma rays reaching the detector have three sources of origin: (1) the natural gamma radiation emitted by the formations, (211 induced gamma radiation resulting from neutron bombardment. (3) gamma rays emitted by the source and scattered by the formation. It has been found that a neutron derived porosity correlation is best for shale-free formations. Under this condition the natural gamma ray radiation is quite low, and therefore, will be neglected in this work. The induced gamma ray radiation resulting from neutron bombardment is predominantly a function of the hydrogen atom concentration of the substance penetrated. Due to the geometry of the presently used system, the neutron-gamma curve indicates low radioactivity opposite high hydrogen concentration and high radioactivity opposite low hydrogen concentration (Figs. 1 and 2). Having a curve which measures hydrogen atom concentration, it follows that if the matrix of the formation penetrated consists only of atoms other than hydrogen, and if the fluid filling the pores is either oil or water, the curve should be an indication of porosity (both oil and water have practically the same number of hydrogen atoms per unit volume'). The above criteria for a porosity (Correlation are fulfilled in clean sandztones and limestones in which the pore volume is completely filled with liquids (oil or water), but not in formations containing either free gas or shale or both. Free gas. even under pressure, contains considerably less hydrogen per unit volume than oil and water; therefore, a variation in response on the curve would be expected. Camp- bell and Winter,' indicate that this difference in hydrogen concentration is sufficient to distinguish between sands containing water or oil and those containing dry gas. Shale is a mineral that contains hydrogen in its molecular structure in addition to the hydrogen which is present in the water of hydration. Thus, in formations containing variable amounts of shale, the hydrogen concentration indicated by the curve is not a direct indication of porosity. Bush and Mardock' have indicated that a correction may be made by use of the gamma ray curve to provide a porosity correlation. Since the induced gamma rays are predominaiitly a function of hydrogen concentration, it would be anticipated that the fluid filled bore hole would materially influence the logs. It has been pointed out that the neutron-gamma curve response decreases with increase in hydrogen concentration, therefore, the response due to the induced gamma ray component decreases with increase in fluid filled hore hole diameter. The scattered gamma ray component of the log increases with increase in bore hole diameter. Although there is an

Jan 1, 1952

By Wayne E. Glenn

A centennial meeting should be a time to take stock, to evaluate performance, to plan ahead. It is like a line in a televised commercial that goes, "You've come a long way to get where you've got to today." And no less should be said of the mining and energy industries. We have come a long way. A hundred years ago when AIME was founded, this country produced 23 million tons of bituminous coal and 5.2 million bbl of oil. The figures in 1970 were about 580 million tons of coal and 4.1 billion bbl of oil. In spite of such accomplishments, serious and compelling voices are heard in the land - doubting sincerity, questioning corporate structures, and challenging ethics. Those doubts are raised in one part of Washington at the same time that other sections of the Capitol are asking us to produce more energy in order to keep up with population growth, emerging nations, and new technologies. Those of us in the fuel or energy business frequently talk about the race for energy. The question is, can we develop enough energy fast enough to outdistance our present and increasing demands? Recently I heard of an incident that - in an odd way - caused me to think of the energy race. The incident involved a sky-diver who jumped from an airplane without a parachute. He was handed a chute in mid-air by a sky-diving companion. He put it on, opened it, and landed safely. In a way, it seems to me that our society is hurtling through space and that it needs some help from the energy industries to land safely. We're doing our best, but under some rather difficult conditions. Because of illegal strikes and work stoppages the coal parachute is snarled a bit. The cut in percentage depletion and other tax changes have put some holes in the oil parachute. And the gas ´'chute has been in trouble for some time because of unrealistic controls on producer prices. The irony of the situation is that some of the very people who have been taking potshots at the energy parachutes for a long time are the ones who are complaining loudest now because the 'chutes are not functioning the way they could. The safety of the entire nation can depend on the energy industries.

Jan 1, 1971