Search Documents

By C. E. Arnold

A brief description of this installation was included in a recent paper by H. Kenyon Burch.l The purpose of the present paper is to amplify Mr. Burch's description, as it is felt by the writer that the subject merits more than passing attention. In making a comparison between the common method of hoisting men in mine shafts, and elevator practice in high buildings, the former shows to great disadvantage both as regards safety measures and smoothness of operation. It is surprising that in view of the inducements offered, the step of applying the building equipment direct to the mine shaft has not been taken before, as in many respects the conditions of service are similar, and the objects to be attained are identical. Even without doing this, it is certain that safety to life and limb in the usual method of hoisting men underground can be greatly enhanced by the application to the mine hoist of some of the features of the building elevator. In the case under consideration, the elevator cage runs in a vertical, concrete-lined shaft compartment 5 ft. 11 in. by 5 ft. 6 in. (1.8 by 1.68 m.) in section and 585 ft. (178 m.) deep, while the counterweight runs in the pipe and ladder compartment of a twin shaft 102 ft. (31 m.) distant. The section of the division of this compartment occupied by the counterweight measures 2 ft. 4 1/4 in. by 3 ft. 101/2 in. (0.72 by 1.18 m.), and the counterweight is made in the form of a small cage which suffices to carry two men for the purpose of making inspections or repairs in the pipe and ladder way. The hoist is designed to carry a load of 7500 lb. (3401.94 kg.), ex-clusive of the cage, which weighs 7500 lb., at a maximum speed of 800 ft. (243 m.) per minute. It is installed in the main hoist and compressor building about 220 ft. away from the elevator shaft and is driven by a 160-hp. direct-current motor which is served by a 190-hp. motor generator set. A small direct-current generator mounted at the end of the motor generator set furnishes the current for the controller magnets, brake and fields of the hoist motor and generator. The drum, which is 72 in. (1.83 m.) in diameter, is driven through the medium of a single reduction herringbone gear. A Francke flexible coupling connects the

Jan 1, 1918

By John T. Norton

In spite of the very general errlployment of nitride hardening, there is still considerable doubt as to the real nature of the mechanism involved. Experience has shown that the addition of small amounts of hardening elements to iron or steel results in a wide variety of desirable properties in a nitrided case. Perhaps the foremost of these elements is aluminum and in this investigation an attempt has been made to study the behavior of aluminum during the hardening process. It is believed that the establishment of a complete atomic picture of the metal at various stages of the process will indicate the relationships between the several kinds of atoms and their individual influences on the physical properties in a clear and direct fashion. A consideration of the problem suggests a surprising similarity between the mechanisms of nitride hardening and of age-hardening. It is now generally understood that age-hardening may take place by one of two distinct processes, the first involving the precipitation of a finely dispersed phase and the other being concerned with the modification of an existing phase. Following much the same line of reasoning, two theories of nitride hardening have been suggested. The first explanation, which has been generally discussed, particularly by Fry,' states in brief that the presence of aluminum causes the precipitation of aluminum nitride during nitriding and that this finely dispersed phase is the primary cause of hardening. The second explanation, which has not been published but which has been freely discussed by those interested in the problem, postulates the substitution of aluminum atoms for certain of the iron atoms in the several iron-nitrogen phases in the same manner that the substitutional iron-alurninurn solid solution is formed. The marked increase in hardness, as compared with the aluminum-free system, is attributed to the severe lattice distortion accompanying this replacement.

Jan 1, 1934

By Karl Sundberg

ElectRical investigations carried out in regions containing sedimentary rocks showed that sediments generally are good electrical conductors, a fact which at the present time is used for structural investigations by electrical methods. It is of fundamental importance, not only for these investigations but also for electrical prospecting in general, to know the electrical properties of various soils and rocks. It will be useful, therefore, to discuss this question with the hope that the general points of view discussed in this paper will perhaps be completed by further observations and determinations of material from various localities. This paper is based principally on the study of literature, and the purpose is primarily a discussion of the main factors that determine the electrical conductivity of soils and rocks. It will follow, however, that the factors discussed here also frequently decide how far a certain orebody can be regarded as a good electrical conductor compared with the surrounding rocks. All rocks are more or less porous, and the pores are filled with liquids and gases. Their electrical conductivity, therefore, depends on the following factors: 1. The electrical conductivity of minerals composing the rock. 2. Electrical conductivity of the liquid filling the pores. 3. Proportion of the volume of liquid filling pores of the rocks to the solid rock material. 4. Shape of the pores. 5. Arrangement of the particles of gas and liquids. 6. Temperature. Dry minerals, with the exception of certain ore minerals, are complete nonconductors from the point of view of applied geophysics; in the present investigation we deal with rocks which have no conducting minerals, and factor 1, therefore, is not important. The same is true of soils. The liquids contained in soils and rocks in most cases are waters, sometimes oil. As oil is a nonconductor of electricity, the impregnating waters will determine the electrical conductivity of soils and rocks.

Jan 1, 1932

By Olaf Hondrum

CHURN drilling equipment at Bagdad consists of two Bucyrus Erie 27-T model drills and one 22-T drill with gasoline engines. The drilling tools weigh approximately 1600 lb. The holes are drilled with 7-in. bits which are heated in an oil burning furnace and sharpened in an electrically powered bit sharpener. A service truck brings the bits to the drills and takes the dull bits back to the shop. The bits weigh around 250 lb. when new and are handled by drill crews without any mechanical handling device.

Jan 10, 1950

SECTION I PAGE PAGE President's Western Trip v Presentation of the' John Fritz Hoover Makes Plea to. Stop Food Medal to Henry M. Howe.... xv Waste v International Mining Convention. xxxv. American Committee of Engineers Personal xl in London vii Employment xlii Proceedings, Meeting of Board of Local Section News xliii Directors : vii Forthcoming Meetings of Societies xlvii St. Louis Meeting V... Library xlviii The Woman's Auxiliary. xi Membership liv Members of the Institute in Mili- Biographical Notice of H. T. Chen. lxxiv tary Service xiv Institute Committees lxxv Officers and Directors lxxxii

Jan 7, 1917

By P. Barnes

In vol.33 of the Proceedings of the Institution of Civil Engineers, London (part 2, for 1870-71), may be found a statement of the cost of two blast furnaces, together with a somewhat detailed description. The attempt will he made in this note to restate these items of cost, so that the information may be rendered perhaps more accessible to our members than in its present place of record, and also in order that the items may be more intelligibly compared among themselves, or with similar items in other cases.

Jan 1, 1879

ENGINEERS AVAILABLE, (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members) Member, aged 33, technical graduate, B. S. and E. M., soon to complete contract in Spanish America, desires to get in touch with employers. Ten years mine, mill, cyanide and construction experience. Prefers executive position or assistant to executive. No. 352. Member; University graduate, desires responsible position with good company. Married.' Age; 37. Fourteen years' experience in Australia, Mexico and United States, milling, cyaniding and concentrating, gravity

Jan 5, 1917

By Emil Schroedter

The death, on May 6,1908, of Dr. Hermarnn Wedding, Privy Mining Councilor of the Kingdom of Prussia, and Professor of the Metallurgy of Iron and Steel at the Royal Mining Academy of Berlin, was a loss keenly felt by the whole metallurgical world. Not alone in his native land, but also in foreign countries, did he enjoy an esteem of which the title of honorary membership in the American Institute of Mining Engineers, the United States Association of Charcoal Iron-Workers, and the (British) Iron and Steel Institute bears eloquent testimony.

Jan 1, 1910

By Roger Thunvik, Carol Braester

Excavation of cavities below the ground water level induces water influx from the surrounding aquifer. An estimate of the rates of flow prior to excavation operations may be of valuable information for the mining engineer. The present paper deals with water influx into cavities of the tunnel type, e.g., mine galleries, tunnels, etc. The solution of the flow problem was obtained by a numerical finite difference method. The results are presented in dimensionless form as a function of the parameters characterizing the location of the cavity in the aquifer.

Jan 1, 1981

ARIZONA Phoenix Arizona Mining Journal. B Carnegie Public Library. B Tucson University of Arizona, Mining Engineering Society. B CALIFORNIA Berkeley University of California, Mining Asso. B University of California, Library. B & T Los Angeles Chamber of Mines and Oil. B Public Library. B & T Oakland Oakland Free Library. T Sacramento California State Library. B. San Francisco Bureau of Mines Experiment Station. 13 California State Mining Bureau. T Mechanic's Mercantile Library. B Mining and Scientific Press. B Stanford University Stanford University Geological and Mining Society. B San Diego Public Library. B

Jan 1, 1923

By W. C. Peters

Geologists take the role of mine geologist when they apply their science to the design and operation of a specific minerals project. In doing so, they use the entire spectrum of procedures in economic geology and engineering geology to deal with a specific system of orebodies and associated environment. The objectives are established by stages in the life cycle of a mining operation as it goes from a prospect to a development project and on to a mine. This paper summarizes the elements of a mining geologist's role, with examples highlighted from the preceding papers.

Jan 1, 1984

By J. A. Herbst, D. W. Fuerstenau

An analysis of the kinetics of dolomite grinding in a dry ball mill reveals that the following approximations apply for the parameters of the batch grinding model: (1) the size discretized selection functions are proportional to the specific power input to the mill, and (2) the breakage functions can be taken as invariant. These approximations are shown to provide the basis for accurate predictions of product size distributions obtained for several mill speed, ball load, and particle load combinations within the normal ball mill operating range. The engineering implications of these findings are discussed.

Jan 1, 1974

By Alexander Bowie

Of the following problems, some have been suggested by recent articles in technical journals, which have led me to believe that the mathematical discussion here submitted may be of use to mining engineers. Problem I. To Find the Grade or Angle of Inclination upon which the Power Required to Move a Loaded Car Down-hill Will Haul an Empty One Up-hill. Let a be the desired angle of inclination; C, the coefficient of' friction; W and w, the weight in pounds of the loaded and of the empty car, respectively.

Jan 1, 1902

TO THE BOARD OF DIRECTORS AND MEMBERS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS GENTLEMEN: Submitted herewith are the report of the Treasurer for the year 1945 and reports for the same year of the following standing committees: Membership, Admissions, Papers and Publications, Mining and ' Metallurgy (Magazine), and Library. To these reports you are referred for additional details. Membership Membership, counting all categories other than Student Associateship, continues the upward trend of the last 10 years, reaching a total, as shown in Table 1, of 12,081. The net gain of 406 would

Jan 1, 1944

By P. D. Bush, E. H. Gates, M. D. Vijayaraghavan, L. F. Engle

The process developed over the last few years by Republic Steel Corporation in conjunction with Colorado School of Mines Research Institute has been used as a basis for the conceptual engineering of full size plants. The paper will cover the equipment design criteria, equipment design itself, and the integration of the complex unit operations. There are unique features of agitation and use of gas media through- out. The paper will provide an illustrative example of the process requirements for a variety of raw material feeds. It will discuss the materials of construction approach required.

Jan 1, 1973

By K. E. Manchester, C. B. Sibley

The feasibility of doping silicon to produce device structres by directly implanting impurity atoms has been demonstrated. Both phosphors and boron ions have been successfully implanted in silicon to produce electrical junctions. Junctions as deep as 1.2 p have been produced by phosphorus ions having energies the order of 80 kev. An electromagnetic separator has been used to controllably produce uniform, large-area implantations for evaluation experimentation. Correlations between junclion depths and ion energies huve been obtained. Orientation effects have been observed and it has been found that the (110) direction is the easy direction for implanting. Monitoring of thermal treatments oj implanted substrates by sheet-resistance measurement indicates a very mild thermal anneal removes most of the damage done during the implantation. These indications are further substantiated by reverse-current measurements of j,inctions Produced by implantation. Electrical characteristics of implanted junctions are compared with those of diffused junctions. We have been interi n the interaction of energetic ions in the III-V groups, in particular boron and phosphorus, with single-crystal silicon to produce type conversion for possible device use. A number of investigators, a few of whom are avies, Kornelson,3 and so forth, have reported on penetration of energetic ions into both amorphous and crystalline solids. While most work has been done with ions of the rare gas and alkali metal groups, some work has been reported by ing, erber,' and others6 in which ions of the 111-V groups have been implanted in single-crystal silicon. A large amount of this work has been done with ion energies in the 100-kev to 1.5-Mev range. An excellent review article has been written by caldin. We have concentrated on ion energies which are in the 10 to 80 kev range, with which over 1500 implanted junctions such as the one shown in Fig. 1 have been produced in silicon substrates with both phosphorus and boron ions. Fig. 1 is a 3-deg angle lap in which the n type area produced by 66 kev P is delineated and the junction is 9500A below the surface. EXPERIMENTAL Implantations reported in this paper were made with the ion source adjusted to produce ion currents in the range of 1 to 2 pa with accelerating voltages varied from 10 to 40 kv. When using doubly charged ions this produced 10 to 80 kev ions. This allowed substrate temperatures to remain below 100°C. Sam- ple movement resulted in beam impingement angle variation of 7 deg from the normal to the substrate surface. Substrate resistivities have been varied through the range of 0.001 to 500 ohm-cm and specimens oriented in three directions, (110), (Ill), and (loo), within 12 deg. RESULTS For the purpose of this paper, discussion of results will be limited to phosphorus implantations with mention of results for boron-implanted silicon. Similar results have been obtained for boron and will be reported at a later date. In Figs. 2, 3, and 4 depth penetration is shown

Jan 1, 1967

Preheating Feature of Leyner Oil Furnace for Heating Drill Steel The No. 3 Leyner oil-burning furnace, used for heating drill steel, is now made with a preheating chamber. By this addition it is claimed that the heating capacity and, effeciency of the furnace are increased about 50 per cent. This preheater is a section which fits between the body and cover of the furnace of the old design. It may be attached to an old furnace by simply changing a few bolts. Referring to the illustration, it will be seen that the lower chamber is used for the final heating and the upper one for preheating. The type of burner now furnished with this furnace is suitable for either high- or low-pressure air. It hats merely to be throttled for high pressures and when this is done, it, is as efficient as burners designed especially for high pressures and eliminates the noise common to such burners. This furnace burns petroleum or any of its oils, such a, gasoline, kerosene, distillate, etc. Oil heating has many advantages. The steel cannot be injured by absorbing injurious elements such as sulphur, phosphorus or other impurities which :ire present in nearly all coals, nor from unequal heating since the flame imparts a uniform temperature; further, o lie steel is in full view of the operator at all times.

Jan 3, 1916

By R. G. Jones, W. L. Kinney, R. E. Schilson, R. S. Wilson, G. A. Clark, H. Suralo

This paper discusses the results of the Fry conventional or cocurrent in situ combustion test, which was conduct-ed in a 3.3-acre inverted five-spot. The depth of the formation was between 880 and 936 ft; the oil had a specific gravity of 28.6° APl and a viscosity of about 40 cp at the reservoir temperature of 65°F. Preceding the combustion test, air injection tests were conducted which, in conjunction with geological studies, were used to evaluate the characteristics of the reservoir. Combustion was initiated on Oct. 13, 1961, with ignition being accomplished by a 40 kw electrical heater. The test phase of the project ended on Oct. 1, 1963. During the test, the average air injection rate was 1,520.-000 scf/D. Throughout the test, production of all fluids— gas, oil, and water—was monitored. Cumulative oil production credited to the project was 100,586 bbl. The cumulative air-oil ratio was 11,500 scf/bbl oil, and the oxygen uti1ization efficiency was 87 per cent. INTRODUCTION The Marathon Oil Co. conducted a successful in situ combustion test, beginning Aug. 22, 1961, at the Fry unit, Crawford County, 111. The purpose of the project was to test the feasibility of cocurrent in situ combustion as a means of oil recovery in the Fry type reservoir. Interest in in situ combulstion as an oil recovery tool has been stimulated mostly by the existence of large reserves of heavy viscous crudes with low expected recovery, usually less than 10 per cent. These are the so-called unrecoverable reserves, and most combustion tests to date have been conducted in this type of reservoir.1-4 In contrast, the Fry combustion test was conducted in a reservoir with a relatively high gravity oil having a relatively low viscosity. This paper discusses the performance of the test. The geology of the reservoir and the field operations are discussed in separate papers.5 TEST SITE The Fry combustion test was carried out in a 3.3-acre inverted five-spot portion of a lenticular body of Robinson sandstone. Net sand was 50 ft thick, porosity averaged 19.7 per cent, oil saturation was 68 per cent of pore volume, and water saturation was 20 per cent of pore volume. The oil in place was estimated at 1,040 bbl/acre-foot, or 171,600 bbl within the 3.3-acre pattern. The water in place was 326 bbl/acre-foot, or 53,800 bbl. The oil has a specific gravity of 28.7° API and a viscosity of 40 cp at the reservoir temperature of 65°F. AIR INJECTION PERFORMANCE Air injection took place in two phases, the phases separated by ignition of the reservoir. In the pre-ignition phase, air injection tests were conducted in the summers of 1960 and 1961. These indicated that the Fry reservoir was confined, and a high return rate of injected air could be expected. This proved to be an outstanding characteristic of the project, as cumulative gas production was 95.3 per cent of the air injected. The difference between the cumulative air injected and the total gas produced can be largely accounted for by the quantity of air stored in the reservoir. An estimated 16 X 10 cf of air remained in the burned-out portion of the reservoir and an indeterminate amount of gas was stored in the unburned but pressurized reservoir. Hence, a complete material balance of gases would account for nearly 100 per cent of the air injected. At times during the test, the daily gas production rate was 98 per cent of the daily air injection rate. Fig. 1 presents the air injection history of the Fry com-

Jan 1, 1966

By K. S. Benson

DEPLETION is a subject of vital importance to the mining industry. Yet, in spite of its importance, its significance is not generally understood. The purpose of this discussion is to clarify the main aspects of the subject from the viewpoint of a metal mine taxpayer.

Jan 7, 1951

By W. A. Vine

When a hole is made in a stressed solid, such as rock pierced by mine openings, equilibrium of the solid is destroyed. To restablish that equilibrium the stress condition in the rock surrounding the opening becomes rearranged. This rearrangement may or may not develop local stresses in the vicinity of the opening which exceed the elastic strength of the rock. Since stability of the opening depends, therefore, on the strength of the naturally occurring rock surrounding the opening, this rock is an engineering material of construction, and all rock affected by the associated opening or system of openings may be considered a structure. The term invert is chosen to describe the formation of the structure built from the inside, as it were, and a consequence of mining rather than an entity built for a purpose. By definition, an invert structure is formed when openings are made underground and is com- posed of that material on the solid side of a rock-air interface wherein the stress condition is affected by the associated opening or system of openings. The shape of an invert structure is never clearly defined; the skin of the structure may be mapped, and even described, but the boundary of the structure within the solid rock mass must be arbitrarily set.

Nov 1, 1955