Search Documents

By O. B. Hopkins

As prefatory to the body of this paper, a few general statements will be made (1) in regard to the history and importance of the asbestos, (2) as to the principal sources of the raw material, and (3) as to the types and modes of the occurrence of asbestos.

Jan 1, 1915

By H. R. Ogden, E. S. Bartlett, A. G. Imgram

Notched and unnotched tensile specimens of wrought and recrystallized, oxygmted and hydro-genated tantalum and columbium were tested over a range of temperatures selected to encompass the ductile-to-brittle transition. Increasing the oxygen content of tantalum and columbium increased their strength, and raised their ductility transition temperature, but did not cause a marked deterioration of notch properties below that of commercially pure material. The adverse effects of oxygen were more pronounced for recrystallized structures than for wrought material. The effects of hydrogen are complicated by strain aging or slow strain rate hydrogen embrittlement at -105°F. However, in general, hydrogen had only a minor effect an strength, but markedly increased the effective transition tem-terature and caused a deterioration of notch properties . BCC metals including the refractory metals in Groups Va and VIa (V, Cb, Ta and Cr, Mo, W) can be expected to undergo a ductile-to-brittle transition and exhibit brittle fractures at low temperatures.' Notch embrittlement is associated with this phenomenon, and can be a serious design problem. Table I compares the tensile transition behavior and notch sensitivity of commercially pure Group Va and VIa refractory metals. The Group VIa refractory metals have considerably higher transition temperatures, and become notch sensitive at higher temperatures, than do the Group Va refractory metals. In addition, the Group VIa refractory metals are sensitive to metallurgical structure. Recrystallized structures generally have higher transition temperatures than wrought material of the same composition. The relatively poor transition behavior of the recrystallized structures of these metals is generally attributed to the segregation of interstitial impurity atoms at grain boundaries. Pronounced sensitivity to structure is not evident with commercially pure Group Va refractory metals, however. Since these metals have higher solubilities for interstitial elements than do the Group VIa metals ,4 it can be expected that higher total interstitial concentrations are necessary to develop a comparable degree of grain boundary segregation and to produce a similar sensitivity of transition temperature to structure. Increasing only the concentration of interstitial atoms in solution would tend to increase the flow stress of a metal in relation to its cleavage fracture stress and thereby raise its transition temperature, but would not be expected to cause a marked sensitivity of transition temperature to structure. A research program has been conducted at the Battelle Memorial Institute to evaluate the effects of interstitial oxygen and hydrogen on the transition behavior and notch sensitivity of tantalum and columbium, and to evaluate the effects of structure on "contaminated" material. EXPERIMENTAL PROCEDURES Notched and unnotched tensile specimens of oxygenated and hydrogenated tantalum and columbium with both wrought and recrystallized structures were tested over a range of temperatures selected to encompass the ductile-to-brittle transition Oxygen levels selected for study in both tantalum and columbium were nominally 500 and 1000 ppm, whereas nominal hydrogen contents were 150 and 500 ppm in tantalum and 150 and 300 ppm in columbium. Oxygen and hydrogen additions were made directly to 6-in. lengths of 1/2-in.-diam electron beam melted wrought bar stock, in a Sieverts Apparatus. Subsequent high-temperature annealing was required for homogenization of the oxygenated material, but was not necessary in the case of hydrogenated stock. The oxygenated and hydrogenated bars were then swaged to 1/4-in.-diam rods. Tensile specimen blanks were cut from the 1/4-in.-diam rods and annealed to achieve stress-re-

Jan 1, 1963

By H. A. Bright, H. C. Vacher, J. G. Thompson

The methods employed for the determination of oxides and oxygen in ferrous materials may be roughly classed in two groups, "wet" methods and "hot" methods, the first group including the iodine, electrolytic, mercuric chloride, hydrochloric acid, nitric acid, and chlorine methods; the second group including the vacuum-fusion and hydrogen-reduction methods. The wet methods depend upon preferential solubility in a selected medium to separate the metallic portion of the sample from the oxygen-containing constituents. Subsequent analysis of the insoluble residue permits the isolation and separate determination of individual oxides and compounds. The hot methods depend upon the reduction of the oxide constituents of the sample by means of carbon or hydrogen at elevated temperatures. With the exception of the recently developed fractional vacuum-fusion method, the hot methods do not identify individual oxides and compounds but yield only a single value representing the sum of the oxygen contents of several or all of the oxide constituents present. With such diversity in the principles and aims of the different groups, it is not surprising that concordance of results by different methods has usually been difficult to obtain. The present cooperative attempt to define more rigorously than has been possible heretofore the accuracy and limits of usefulness of the various methods, originated in correspondence between Dr. John Johnston, Director of Research of the United States Steel Corporation, and other interested metallurgists. The plan was, briefly, to submit identical samples to a number of laboratories for analysis by different methods and to collate the results of these analyses. The project was endorsed by the Iron and Steel Division of the American Institute of Mining and Metallurgical Engineers at the annual meeting in February, 1933, and has been conducted under the joint sponsorship of the Iron and Steel Division and the National Bureau of Standards. The latter organization undertook

Jan 1, 1937

By J. J. Van Nouhuys

THE economics of aerial survey and the technical processes by the aid of which vertical and oblique aerial photographs are turned into line maps showing the most profuse topographical detail such as contours, rivers, roads, plantations, habitations and cultivated lands do not concern us here. They have been ably and exhaustively described in the publications of the British War Office, handbooks on surveying methods and on photogrammetry and in the South African mining, engineering and geological press. Suffice it to mention that for geological interpretation vertical photographs are used on such scales as 1/5000 to 1/10,000, overlapping each other by 55 to 60 per cent in the direction of flight and some 10 to 20 per cent sideways on to the next sequence or strip. Through this duplication in the overlap the stereoscopic examination becomes possible. The standards by which monochrome aerial photographs are interpreted can be grouped under the following headings: 1. Continuity.-The continuity of topographic relief not obtainable on the ground owing to the smallness of man relative to that relief. Here lies the greatest value of aerial survey with relation to geology. An immediate alignment can often be made of drainages running in different directions on each side of a hill; saddles and gorges in the mountainsides; abrupt termination of outcrop or indubitable signs of faulting. Most conclusive evidence is thus often obtained about faults which may be perfectly visible at one place on the ground but cannot elsewhere be identified because of decreased throw. Similarly, dikes can often be followed notwithstanding frequent interruption and disappearance under the soil. Scattered outcrop in scrub-covered or bush-covered country can be compared with field work. The same applies to geological contacts. Once these have been 3stablished at a few points on the ground, the intervening stretches can be drawn in.

Jan 1, 1937

By R. P. Heuer

In recent years an increasing amount of research work has been done on refractory materials for use in copper-smelting furnaces. A few of the larger refractories manufacturers have erected special research laboratories which are fully equipped to study the refractory problems of the smelter. A typical laboratory of this type was described in the January, 1929, issue of Mining and Metallurgy, in an article entitled "Methods of Research Newly Applied to Refractories," by W. F. Boericke. This particular laboratory is equipped for the manufacture of full-size refractory brick. It aims to study on a fairly large scale the behavior of various refractory raw materials and the effect of improved methods of manufacture. The refractories manufacturer has at his disposal the naturally occurring refractory oxides in various degrees of purity, mixed or combined with other oxides. In order to supply the copper smelter with a refractory brick that will permit the most economical operation of the smelting furnaces, it is necessary to have the optimum combination of a number of both physical and chemical properties in the brick. Unfortunately, nature has not provided any raw materials in which the perfect combination of these properties exists. It is, therefore, a problem for man's ingenuity to seek out the most desirable raw materials and develop methods of manufacture that give, in the resultant product, the necessary combination of properties in as full a measure as is possible. In the laboratory it is possible to carry out fairly broad experiments with this objective. It is first necessary to obtain and process the raw materials, then to manufacture them into brick and finally, to test these bricks under conditions designed to interpret or simulate in the laboratory the actual conditions in the smelting furnace. It is necessary for the research engineers to determine certain fundamental properties in the brick which may be subjected to laboratory measurements and to interpret these measurements in terms of brick performance in smelting-plant practice. Such procedure is not what might be called an exact, scientific one but it has been found that great progress can be made when these principles are applied. For example, the resistance of refractory brick to spalling and thermal change can be related to the thermal expansion of the refractory, its thermal conductivity and heat capacity and its

Jan 1, 1934

By A. R. Kinkel

Robert T. Walker and Woodville J. Walker (Walker Engineering Corp., Salt Lake City)—Mr. Kinkel's article embodies, in condensed form, the results of the first detailed and complete geological survey that has ever been made of the long neglected but potentially very important West Shasta Copper-Zinc district, in Shasta County, California. In view of the difficulties of the terrain and the complexity of the geological structure, this represents a notable achievement, and it is with regret, therefore, that the writers find it necessary to differ from Mr. Kinkel's conclusions on two important points. The first has to do with the interpretation of two members of the stratigraphic column of formations in the district; for purposes of comparison, the description of these two members according to Mr. Kinkel is shown parallel to the description of these members according to the writers, see Fig. 14, Mr. Kinkel's nomenclature being used. The first member, which Mr. Kinkel terms the upper unit of the Balaklala rhyolite, consists of a single, massive, homogenous body of very silicious igneous rock, consisting almost wholly of quartz and albite, and averaging about 80 pct silica. Most geologists of the U. S. Geological Survey who have previously inspected the district have called it an alaskite. It is not a pile of several members, but is a single unit, without internal subdivisions. It has the form of a recumbent lens, approximately flat on the bottom and arched on top, several miles in diameter, and attaining a maximum thickness of 1000 to 1200 ft. It varies in texture from porphyritic to holocrystalline, and contains unusually large quartz phenocrysts up to 4 mm diam. Mr. Kinkel considers this formation to be a thick lava flow that is older than the overlying Kennett shale, while the writers interpret it as being intrusive, constituting a domed sill or laccolith that is younger than the Kennett shale. Their reasons are as follows: 1) This formation shows none of the features which within the writers' experience invariably accompany very silicious lava flows. Nowhere is it vesicular; nowhere does it contain any glass or its devitrified equivalent; nowhere does it contain flow breccia; and nowhere has it a ragged top, in spite of the fact that there is no evidence of surface erosion, which might have removed such a top.

Jan 1, 1957

Dr. Arthur H. Elliott has been connected with the gas industry for upward of thirty-eight years and was a chemist to whom the industry is deeply indebted for the application of the science of chemistry to its problems and processes. He was born in London, England, in 1851, and was the son-of a physician. While a child he was taken to France, where he received his early education, learning to speak the French language before his native English. His father having destined him for the medical profession, he commenced his studies on his return to England, but his attention being attracted to chemistry, he gave up the study of medicine to pursue that of chemistry. While still a student, he obtained a reputation as an iron and steel analyst, publishing two methods of analysis, one for the determination of sulphur .and the other for the determination of carbon in cast iron. On his graduation from the School of Mines at South Kensington, he left England intending to go to Australia, where an uncle resided, having in mind also the possibility of a trip to China. On his arrival in New York, he met Professor Charles F. Chandler, to whom he had a letter of introduction, and who induced young Elliott to remain. He graduated from Columbia College with the degree of Doctor of Philosophy in 1883. He became demonstrator in chemistry at the College of Pharmacy and afterward professor of chemistry and physics at the same college. He became connected with the Municipal Gas Lighting Co. in May, 1880. In. November, 1.884, when consolidation took place, he became engineer-chemist of the Consolidated Gas Co., which position he held until May, 1910, when he resigned, but was retained as consulting chemist until his death. Recently Columbia University conferred on him the honorary degree of Master of Science.

Jan 7, 1918

W. H. LINNEY, Chairman, OSCAR LACHMUND, Vice-Chairman LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154; Spokane, Wash. STANLY A. EASTON, S. SHEDD. Mining camps from Mexico to Alaska and from the Pacific coast to the Atlantic were represented by delegates at the 5th Annual Northwest Mining Convention which was held in Spokane, Wash., Feb. 19-24, 1917. About 300 delegates from outlying regions were present, this being fully 100 more than have been counted at any previous mining convention in Spokane. Graham B. Dennis, president of the Northwest Mining Association, made the address of welcome. In part, he said: "Heaven has made us the possessors of an area great enough for an empire, varied enough in climate and possibilities to compass the whole complex field of modern industry. In the development of this broad heritage, we are not only actors for today, but trustees for future ages. "It is to foster this spirit of unity; to create and maintain strong bonds of mutual good will and confidence, that we founded the Northwest Mining Association. Wee support it because we believe it will give us strength; because we believe we shall learn from each other; because, in industry as in every other walk of life, personal contact and establishment of ties of friendship enrich and round out the characters of men." One of the interesting lectures of the week was that on "Alaskan and Russian Gravel Mining," by Dr.' Henry Mace Payne, consulting engineer for the Russian government and Consolidated Goldfields of South Africa. Dr. Payne's illustrations showed the different appliances in use in the countries mentioned. The Resolutions Committee reported back to the Convention six of the seven resolutions that had been presented to it. These were adopted as submitted, with some minor changes.

Jan 5, 1917

By Robert L. Davidoff, Rodney D. Rosenkranz

In order to determine copper resource data and production costs for major market economy mines and deposits, the Bureau of Mines has performed detailed engineering and economic analyses on 271 of the world's most significant copper deposits. At the demonstrated resource level, copper potentially recoverable from these deposits is estimated to be 325 million metric tons, 180 million tons of which would be from Pacific Rim countries. Chile has the largest known copper resources of any country and accounts for nearly 45 percent of the copper avail- able from Pacific Rim countries. At $1.00 per pound, in January 1981 dollars, an estimated 80 million metric tons of copper are potentially economically recoverable from Pacific Rim deposits. At this same price, analyses indicate that these deposits could economically produce about 2 million metric tons of copper per year. Sensitivity analyses reveal that if operating costs were to decrease 25 percent, with copper at a price of $1.00 per pound, total copper economically recoverable from Pacific Rim countries could increase by about 10 percent; a 25 percent increase in operating costs could lower economically recoverable copper by 50 percent. Analyses also indicate that byproduct prices are important. If byproduct revenues increased 25 percent, at a copper price of $1.00 per pound, an additional 2 million metric tons of copper could be recovered; if byproduct revenues decrease 25 percent, about 5 million metric tons less of copper metal would be available. Since the January 1981 date of this study, inflation and decreases in copper and byproduct prices have greatly affected the profitability of the world copper industry. Many producing mines have curtailed or suspended production, and development of many non- producing deposits has been postponed.

Jan 1, 1982

By Thomas C. Baker

The Fresnillo unit of the Mexican Corporation, S. A., is situated at the old historic mining town of Fresnillo, Zacatecas, Mexico, 33 miles north of the city of Zacatecas and 750 miles south of El Paso, Tex. It is connected with the Mexican Central Railroad by a broad-gage spur 5.5 miles long, belonging to the company. Fresnillo is surrounded by a broad semi-arid valley on the Mexican plateau at an elevation of 7300 ft. The monotony of the valley is broken by a number of low hills. Near the town of Fresnillo is the " Cerro de Proano," an elliptic-shaped hill of gentle slope, rising out of the plain to a height of 325 ft.; the base has a major axis of 4500ft. and a minor axis of 3000 ft. In this hill is the silver-bearing mineralized zone, which comprises past and present mining operations. (In this paper money values are expressed throughout in American currency and the dry short ton of 2000 lb. is used.) The discovery of ore at Fresnillo is credited to the Spaniards, soon after the conquest of Mexico. There are, however, no authentic records to show the amount of work done by them. In 1832, the State of Zacatecas took possession of the property and operated it. Evidently the rich ore above the horizon of the plain had been fairly well exhausted, as an old record states that thirty shafts were used for unwatering, requiring 300 men and 1500 animals. The cost of pumping alone amounted to $150,000 a year. In spite of the fact that cheap convict labor was used, mining costs were reported as $20 and treatment charges as $20 per ton. In 1835, the state was obliged to seek foreign capital, and a company formed in London secured a controlling interest in the property. This new organization sank two shafts, one 11 by 19 ft. and the other 10 by 15 ft., to unwater the mines and extract ore. Large Cornish pumps were purchased in England and hauled overland from Vera Cruz; engines also were installed to operate the arrastres (grinding mills) in the patio process of ore treatment. Substantial buildings were erected and operations were conducted on a large scale, for that period. The patio, the largest in Mexico, was 1150 ft. square. The costs for 1850 were:

Jan 1, 1925

This story of the salting of a supposed diamond mine is a part of our Western history and deserves to be recorded in this book. It was more than a local affair, because it was concerned with persons in London and New York, as well as San Francisco. Part of the story has been told by Asbury Harpending in a little book published 12 years ago. Harpending (who died at New York in 1923) was in London in March, 1872, when he received a cable dispatch from William C. Ralston, the president of the Bank of California, stating that "a vast diamond field" had been discovered "in a remote section of the United States". Before starting for San Francisco, Harpending had an interview with Baron Rothschild, who showed a lively interest in the story, which was as follows: two weather-beaten prospectors went to the Bank of California and deposited some uncut diamonds and rubies for safe keeping; these precious stones were estimated to be worth $125,000. The men said that they had found the gems in "a desert portion of the West". They departed quietly, but the story was told in business circles; whereupon George D. Roberts, a mining engineer of wide experience and an associate of Ralston, sought an interview with the prospectors. One of them proved to be a man that had been in the employ of Roberts. Both prospectors, named Slack and Arnold, appeared "coy and cautious"; they were "simpleminded fellows", and were "afraid to trust anyone with the momentous secret ". They refused to divulge the place of discovery and declined "to part with their rights", but later "they became more amenable to reason" and expressed willingness to sell a half interest to

Jan 1, 1932

By W. N. Page

Among engineers engaged in mining coal for river transportation, probably no other subject of equal importance has received so little attention as the methods of transferring into barges and other craft. The liability of all our streams to sodden freshets and their attendant drift and ice-gorges, seems to have had little effect upon the design and construction of what are commonly known as rivertipples, beyond the building of breakwaters, and other similar devices, to guard expensive structures from damage. The first method adopted for such transfer was a simple incline, with a movable cradle, which could be raised or lowered to suit the different stages of water. This system, though limited to a small capacity, and to cars not larger than those commonly used underground, possessed two advantages. The first cost was comparatively small; and, since the structure did not obstruct the channel, there was little risk from freshets, the utmost damage from which could be repaired at small expense. Its disadvantages, however, were many, the principal among them being the breakage of the coal by reason of the necessarily high dump; the damage to barges from the same cause; and the difficulties of screening and distributing the different sizes into separate barges. That system has been almost wholly abandoned of late, in favor of the basket-arrangement, lowering vertically into the barge, with the aid of counter-weights, which return the empty basket; while pipes or chutes convey the small coals into other barges, from a complete set of screens, which this method will readily accommodate. As far as my observations have gone, the latter system is now universally employed along all the tributaries of the Ohio. It

Jan 1, 1889

By T. F. Witherbee

THE Fletcherville Furnace was built in 1864 and 1865, making its first blast from August until October of the latter year, when it was blown out to prevent its "bunging-up." Repairs were made in time to enable it to be blown in again December 12th, 1865, the blast ending October 7th, 1866. Total product 1921.15 tons iron, an average of 6.8.2.5 tons per day, from ores yielding 44.8 per cent. Consumption of charcoal 223.2 bushels per ton of iron. The furnace journal up to this time shows no record of furnace dimen¬sions, or temperature of the blast, but as near as can be ascertained, they were as follows, viz. Height of stack, 42 feet. Diameter of bosh, 11 feet. Angle of bosh, 7 1/2 inches to 12 inches rise, about 58°. Diameter of open tunnel head, 42 inches. Number of tuyeres 3; each 3 inches in diameter. Dam 15 inches high. Tuyeres 24 inches high. Tymp 22 1/2 inches high. Diameter of steam cylinder, 20 1/4 inches. Stroke 5 feet. Diameter of blast cylinder, 64 inches. The engine is direct-acting horizontal non-condensing. December 26th, 1.866, the furnace was again put in blast, having been considerably altered in the crucible; the height of stack, bosh, and tunnel head remaining as before. Six tuyeres were put in, three in each of the side arches. The hearth or crucible was rectangular in form, 3 feet wide x 32 feet long x 62 feet high. Inclination of bosh 58°. Height of tuyeres 26 inches ; nozzles 2 1/4 inches diameter. Temperature of blast estimated to be about 500°.

Jan 1, 1874

By John M. McAnerney

In 1955, the U.S. Army started to experiment in Greenland with tunneling in glacial ice and later in frozen glacial moraine. By 1960, long adits and experimental rooms had been successfully excavated. Full mechanization with coal-cutting machinery was most efficient in ice but drilling and blasting were necessary in bouldery moraine. In 1963, the U.S. Army Cold Regions Research and Engineering Laboratory, (USA CRREL; redesignated U.S. Army Terrestrial Sciences Center July 1, 1968) started a tunnel in the frozen silt of central Alaska near Fairbanks. The original adit of 360 ft (109 m) was successfully driven in the permafrost by a twin-rotor tunnel-boring machine, the Alkirk Cycle Miner. The workings were enlarged in 1966 and 1967 by standard mining techniques in which jackhammers, steam points, and augers were compared. A mechanical coal cutter was tried to supplement drilling and blasting. In 1968, airblasting techniques were used successfully for breaking out the frozen silt. All mine products were loaded mechanically and hauled by self-dumping shuttle car. Pneumatic methods of transport were tried for both dust removal and for conveying blast products up to 3-in. maximum size. Studies of the effects of natural winter ventilation through a shaft showed that tunnel closure could be reduced by lowering the adjacent ground temperature. It is concluded that underground openings in frozen ground should be cut and maintained at well below freezing temperatures to hold deformation to a minimum. HISTORICAL BACKGROUND This chapter deals with aspects of tunneling not previously discussed in the conference papers in this book. The chief differences are that the three tunnels lie entirely within frozen material and are relatively small, since they were constructed mainly for research. The primary objectives of the research were to develop underground shelters for military per-

Jan 1, 1970

By George J. Young

The recurrence of mine-fires in Nevada during the past decade is not only a matter of interest, but also one of considerable concern to engineers and mine-managers. The more important fires may be enumerated as follows: Forman Shaft fire, Gold Hill, April 21, 1903; shaft-house, machinery, and shaft destroyed; loss estimated at $50,000; cause unknown. Union Shaft fire, Virginia City, July 14, 1904; shaft-house, machinery,and shaft in part destroyed; loss estimated at $100,-000; cause of fire stated as the careless throwing of a match in the rope-house. Sutro Tunnel fire, Virginia City, Jan. 27, 1909; 700 ft. of tunnel-timbering destroyed, and direct damage of $10,000; cause " probably electric wires." Belcher Shaft fire, Gold Hill, Aug. 9, 1910; shaft-house destroyed, machinery ruined, and upper part of shaft damaged; damage, $25,000; no cause given. Belmont Mine fire, Tonopah, Feb. 23, 1911; fire started ill winze; 17 men killed. Giroux Mine fire, Kimberly, Aug. 23, 1911; fire originated in shaft-station from unknown cause; 7 men killed, and $34,-521 damage caused. (Note 1.—On June 11, 1912, some time after the present paper was written, a fire broke out in the pump-room on the 2475 station of the Ward shaft, Virginia City. This fire was caused by the short-circuiting and exploding of the starting-switch on No. 5 pump. The oil in the switch was scattered about and set fire to the timbers and lagging of the pump-room. The pump-man in charge notified the surface, and the electric current was shut off. A hose was then turned on the fire, but the dense smoke drove the attendant out. Inspection by the electrician and the shaft-foreman, equipped with oxygen-

Jan 1, 1913

By Louis Cates

AT THE annual meeting of the American Institute of Mining and Metallurgical Engineers in February, 1923, the Chairman of the Committee on Ground Movement and Subsidence appointed a subcommittee to work out a form of questionnaire and to collect data on subsidence and ground movement resulting from underground metal- and coal-mining operations, and on ground movement and safe slopes in connection with open-cut metal-mining operations. The author was requested to take charge of the collection of data and the preparation of a questionnaire in connection with the Committee's studies of open-cut metal-mining operations, this paper is a summary of the work carried on and information received therefrom up to February, 1924. The first approach to the problem of safe slopes is to gather all information that pertains to finished slopes; in other words, the steepest economic angle from the horizontal that will stand in order to uncover the ores to be mined and be safe while the extraction of the ore at the base of these slopes is in progress. Whether or not this angle is 35° or 45° depends on many factors. The number of benches maintained to take care of falling rock and their height and width are direct functions of this overall slope. The slope is here taken to mean the angle from the top edge of the pit through the edges of the respective lower benches to the bottom of the pit. If we accept this definition of the slope, it might save some confusion as there would be a difference if one took the line from the top edge of excavation to the toe of the bottom slope. This latter slope would not be constant, but would vary with the number of benches. The depth of the various ore faces will vary, of course, depending on the deposit; Table 1 shows this to range from 50 ft. to 1100 ft. The geology is an important factor, as are the climatic conditions under which one is operating. A saturated condition in some rock structure causes rock flows; in the Panama Canal excavation, slides have run on a ratio of as low as one on ten, which is a 10 per cent. grade, or a slope of less than 6° with the horizontal. Slopes as steep as 60° have been noted in the Utah Copper operations, so that a wide divergence will possibly be

Jan 8, 1924

By F. M. Lewis, J. E. Goodman

A larger, slow-speed, under-loaded ball mill and hydraulic classifier have almost doubled grinding efficiency at the lsabella mill. TENNESSEE Copper Co. operates two ore con-A centrators, the London and Isabella mills near Copperhill, Tenn. In 1948 and 1949 the small ball mills and rake classifiers in the London concentrator were replaced by one large ball mill and one hydraulic classifier. This new ball mill was designed oversize so that it could be operated at slower than normal speed. The proper operating conditions were established and the results published.' Later it was found that this mill operated more efficiently with a small ball charge." While this London grinding practice was being developed, the Isabella grinding circuit was not changed in any way. It remained a conventional two-stage rod mill—ball mill combination, the rod mill in open circuit and the ball mill in closed circuit with a rake classifier. Study of the data indicated that grinding cost could be lowered by converting to the London practice, but not enough would have been saved to warrant the expense of converting. No plan for improving this grinding operation could be developed. In 1953 this study was reopened when plans were made to increase the Isabella mill output from 1150 to 1500 tpd. At this time the grinding circuit consisted of a 6x12 rod mill followed by a 6x12 ball mill in closed circuit with a 6-ft rake classifier. Another 6x12 ball mill and 6-ft rake classifier would have been sufficient equipment and would have been the simplest and cheapest installation. However, this would have offered no improvement in grinding efficiency or operating cost. If, on the other hand, the grinding operation could be converted to the London practice, by installation of one large 101/2x9x9 tricone mill and a 10-ft hydroscillator,2 lower operating costs would justify the additional investment. Economics: Table I presents estimates for the two schemes for enlarging the Isabella mill. In the first scheme, column 1, one 6x12 ball mill and one 6-ft rake classifier were to be added. In the second scheme, column 2, the existing small ball mill and rake classifier were to be retired and one large mill and hydroscillator were to be installed. Estimated savings from the difference in operating costs made an attractive return on the additional investment for the large mill and hydroscillator. Actual costs of carrying out this plan are tabulated in column 3b. It will be seen that these costs follow the estimates in column 3a very Closely. The return on the additional investment is calculated from the difference in the operating cost in column 1 and the actual operating cost in column 3b. This too come very close to the estimate. Power and Steel: Power requirements and steel consumption for the rod mills and ball mills, both actual and estimated, are presented in Table 11.

Jan 1, 1958

By D. Turnbull

RECENTLY it has been shown that aggregates of small liquid droplets of tin,' mercury' or gallium' kept from intercommunicating by suitable films do not solidify at an appreciable rate unless the supercooling is very much greater than that usually necessary to cause a large continuous mass of the metal to solidify. For example oxide-coated tin droplets1 (1 to 10 micron diam) must be supercooled 100" to 110°C before their rate of solidification becomes rapid, although large continuous masses of liquid tin usually begin to solidify when supercooled 30" or less." These experiments have been interpreted' on the hypothesis that nucleation of crystals in large continuous metal samples is almost always catalyzed by accidental inclusions. Therefore, if the metal is dispersed into a number of isolated droplets large in comparison with the number of inclusions, most of the droplets should not crystallize until a temperature sufficiently below the thermodynamic melt- ing point, T0, has been reached to permit an ap-preciable rate of homogeneous (noncatalyzed) nu-cleation. In general this temperature is very much less than the temperature at which the rate of heterogeneous (catalyzed) nucleation is appreciable. If this interpretation is correct then investigation of the kinetics of crystallization of small droplet aggregates should be one of the most fruitful methods of obtaining information about the homogeneous formation of crystal nuclei in liquids. In this paper the results obtained on gallium and mercury are reported more fully. In addition, results on the supercooling of aggregates of liquid bismuth and lead droplets are included. Experimental Procedure Some care must be exercised in the choice of a barrier to prevent the liquid droplets from coalescing lest the barrier itself catalyze the formation of crystal nuclei. From this standpoint, the most desirable barrier is vacuum or inert gas, but, because of the difficulty of experimental arrangement, solid compounds and adsorbed films have been selected. There are two guiding principles in the selection of compounds as barriers in addition to the requirement that they prevent coalescence of liquid droplets. First, the compound should be almost insoluble in the liquid metal and second, its lattice structure should be quite unlike that of the forming metal crystal. Even so, there is no a priori assurance that the solid compound film will not catalyze to some extent the formation of metal crystal nuclei. An adsorbed protective monolayer is less likely to be catalytic than a crystal compound film, but it is not often possible to find a monolayer that is stable under the experimental conditions. Also, it is desirable, though not generally essential, that the aggregate of droplets be prepared by breaking up the massive metal rather than from a powdered compound of the metal.

Jan 1, 1951

By J. J. Bowman

The term "secondary aluminum" frequently is used loosely and often is considered synonomous with "inferior quality." Under war conditions, when every pound of material must contribute its share to the job at hand, this type of thinking is most unfortunate. Actually, given a supply of segregated scrap, an experienced smelter can produce remelted ingot of good quality, comparing closely to the analysis of the original material, and of considerable value of the war effort. The alloys he can produce are, of course, somewhat controlled by the analysis of the available scrap and, by the very nature of things, some of his production is not suitable for indiscriminate use. However, remelted scrap ingot provided about 273,2 per cent of this country's domestically-produced 1942 aluminum supply and probably will comprise about 39 per cent of the 1943 supply. (Canadian production is excluded from these figures.) That this part of the supply remains important is indicated by a recent report that "requirements" for the second quarter of this year were about 14 per cent greater than the supply, even though that supply will be almost twice the prewar annual production. (And those requirements, incidentally, were prepared after many conservation measures had been taken into account.) Since W. Bonsack recently has published a paper2 on the effects of the various alloying elements and impurities on the properties of aluminum, and such con¬siderations really are the important ones in a discussion of the metallurgy of secondary aluminum, it is planned to restrict this discussion more to a consideration of the sources, general characteristics and possible uses of these materials. For the purpose of this discussion, mill (or run-around) scrap may be disregarded and only plant scrap and obsolete scrap considered. Plant scrap, of course, is that scrap which is generated during the production of some part or assembly from a fabricated form of aluminum, such as sheet, tubing, forgings, castings or the like, and it may consist of solids (including rejected parts or subassemblies) or of machinings. To the extent that the several alloys are effectively segregated and the material is properly identified, the composition after remelting can be rather closely controlled or predicted. Obsolete scrap, on the other hand, is the "junk" which accumulates because of the wearing out or breakage of some piece of equipment. Although it is almost always in the form of solids, the accumulation includes many different alloys (often in the same assembly) and may include a considerable amount of nonaluminum material. The "metallics" recovered from drosses also contribute a portion of this class of material. The composition after remelting, therefore, may vary over rather wide limits and can not be very accurately predicted in any specific instance. SEGREGATION OF PLANT SCRAP Unfortunately, perhaps, it was not very common practice before the war to

Jan 1, 1943

By S. H. Williston

IT not often that bore hole surveys can be checked by actual. civil engineering methods. A recent Arizona survey was checked by normal surveying methods and the comparison of the results should be of value to both oil and mining men. During the summer of 1948 the Phelps-Dodge Corporation, at its Copper Queen property near Bis-bee, Ariz., drilled a 1245 ft, 8 in. diarn, churn drillhole in a mineralized area and cased part of it, intending to use it to transfer mill tailings for stope fill. The hole, as frequently occurs, was not straight, and, in endeavoring to locate the bottom in the underground workings, they found no evidence of the hole at the underground coordinates directly below the surface location. The noise of the drilling tools was reasonably clear, but the direction of sound was uncertain. Preliminary tests with available equipment were not successful in locating the bottom of the hole. Because of the mineralized character of the area and the fact there was some casing in the hole, any magnetic method of well surveying would give results of doubtful value. Sperry-Sun gyroscopic well-surveying instruments were finally used to locate the bottom of the hole. These instruments consist of a gyroscope to determine azimuth and either a pendulum or bubble inclino-meter. A multiple shot camera photographs both instruments on a single film and superimposes the photograph of a watch. Coordination of depth with time at the surface makes it possible to select the corresponding picture for any depth. After making several runs of the empty instrument housing from the top of the hole to the bottom to make sure there were no obstructions in the hole, three surveys on wire line were completed during the afternoon. The three surveys, in which readings were taken at different points in the hole on each survey, were computed and gave the following locations of the bottom of the hole in relation to the surface collar: survey No. 1—24.92 N, 30.30 W; survey No. 2—24.24 N, 31.11 W; survey No. 3—26.54 N, 27.72 W. Then the data from the three surveys were combined into a single set of calculations which gave a location for the bottom of the hole: combined surveys—24.27 N, 30.16 W. (Fig. 1.) Immediately upon the determination of the coordinates at the bottom of the hole, a drift on the 1300 ft level was started toward the indicated loca- tion some 38 ft northwest of the coordinates of the surface location, The bottom of the hole was located within the drift round in which it was expected, and the transit survey run to the actual location of the hole indicated N 27.18, W 29.71. This shows a discrepancy between the well survey and the transit survey of 0.45 ft in the westerly direction and 2.91 ft in the northerly direction. All surveys, both gyroscopic and transit, fell well within the width of an ordinary drift. While this is satisfactory for almost any and all mining requirements, a theoretical examination was made as to reasons for the discrepancy. A study of the course of the hole indicates that considerable right turn or spiral existed, and in all probability the surveying instrument was pulled out of alignment while traversing the turn by approximately 0.05 ft at the top and another 0.05 ft in the opposite direction at the bottom of the instrument. If such an allowance were to be made, the survey calculations would almost exactly correspond with those determined by transit. This sort of discrepancy would be minimized by the use of stabilizing guides. It is unfortunate that physical laws probably effectively prevent the use of gyroscopic instruments in EX and AX diamond drill holes. The directive power of a gyroscope falls off inversely at some rate between the third power and the sixth power of the diameter. Present instruments can be run in casing 53/4 in. ID or over and might be adapted to somewhat smaller diameters, but the difficulty of reducing these diameters to 11/4 in. or 2 in. is almost insurmountable at the present time. Acknowledgment The author wishes to express his appreciation to the Phelps-Dodge Corporation for permission to publish this article, and to the Operating and Engineering Departments for their cooperation on the survey; also to Donald Hering, of the Sperry-Sun Well Surveying Co., who actually made the survey and calculated the results.

Jan 1, 1951