Search Documents

By D. L. Marshall, O. F. Thornton

Results of the determination of the inter stitial water content of several core samples from oil reservoirs are presented. Data obtained by the capillary pressure method, which has recently been developed, are compared with water saturations measured in cores cut with oil-base mud and with values calculated from the electrical resistivity of the formation. The agreement between the capillary pressure and other methods, combined with the fact that similar agreement has been obtained by others, indicates that the capillary method properly applied yields results sufficiently accurate for most engineering purposes. In some cases, it may be possible to extend the utility of data obtained with the capillary pressure method by correlation of interstitial water saturation with more easily measured physical properties of the media. Introduction Several methods are in use for determining or for estimating the interstitial water saturation at given points within oil and gas reservoirs. The direct measurement of the water content of cores obtained with nonaqueous fluid in the hole is believed to be an accurate method under most conditions. The water saturation may be calculated by use of the resistivity curves of the electric log,' although this method is not applicable under conditions that exist in some reservoirs. Recently, a method has been developed and described3.' wherein the interstitial water saturation of cores is measured at a capillary pressure such that conditions existing in the reservoir are simulated. The purpose of this paper is to present data obtained by use of this latter method, and to compare the results obtained with determinations made by other means. Method The theory underlying the capillary pressure method applied to petroleum reservoirs has been discussed adequately in the literature by Garrison,2 Leverett,5 and Others.3,6,7 Briefly, and simply, capillary pressure is defined as the difference in pressure between two contacting fluid phases, such as oil and water. For the simplified sand, water and oil system illustrated in Fig I, the pressure difference can be stated as follows:6 where Pc is the capillary pressure in pounds per square inch, ? is the interfacial tension between oil and water in pounds per inch, r1 and r2 are the radii of curvature of the interface between oil and water in inches. Capillary pressure varies in a given reservoir with depth because of the greater density of the water phase as compared with oil or gas. The following equation expresses the difference in pressure between two points: p1- p2 - h?p/144 [2] where p1 — p2 is the capillary pressure difference in pounds per square inch, h is

Jan 1, 1947

By R. A., D. L. Sponseller, Flinn

Using specially del'eloped titanium nitride crucibles and a pressurized syslem, it has been possible to determine the solzibilitv of liquid calcium in liquid iron and iron-base alloys. At 2925°F the solubility is 0.032 wt pet Ca in pure iron. The solubility is increased by aluminum, carbon, nickel, and silicon additions, and lowered by additions of gold. An inflection in the calcium-solubility curve occurs as carbon is added to iron. At approximately 0.87 Wt pet Ca the CaC, phase replaces liquid calcium, and the calcium concentration de- creases as more carbon is added to the iron. The maximum solubility, 0.36 wt pet Ca, was obtained in iron containing 10.5 wt pet Si. The data have important implications regarding the use of calcium in process metallurgy, as well as providing an interesting test of theories of metallic solutions. Reasonably good agreement is found with theories of Alcock and Richardson and of Wagner, and criteria are suggested which permit these theories to be applied more readily to systems of this type. AT the present time relatively little is known about the factors influencing solubility in liquid metals. Information of this type is important for such matters as the control of impurity levels in liquid metals, the use of magnesium in ductile-iron production, and the use of liquid-metal alloys as fuels and coolants in nuclear power plants. One important example of restricted solubility concerns the extent to which liquid calcium will dissolve in liquid iron. This is a matter of considerable interest in view of the strong potential of calcium for removing certain impurities in steel,. as well as the ability of calcium to desulfurize, inoculate, and produce spheroidal graphite in cast irons.' Since ferrous materials normally contain other elements in addition to iron, the interactions of third elements with the Fe-Ca system are of interest. In view of the foregoing, this investigation was conducted to determine the solubility of liquid calcium in liquid iron and the effects of various third elements upon the solubility. For reasons of theoretical and engineering importance, the elements investigated were aluminum, carbon, gold, nickel, and silicon. Numerous attempts were made in the early part of the present century to determine the solubility of calcium in both liquid iron and steel, employing a variety of open-melt and closed bomb-type systems.2-4 From the results of these tests Wever concluded that calcium is insoluble in liquid and solid iron.5 These investigations were unsatisfactory in that they failed to insure the presence of a liquid layer

Jan 1, 1964

THERE have been two important accomplishments of the Truman administration; the Hoover Commission report on inefficiency and waste in government and the report of the Paley Commission on the natural resources of the United States. Both reports are in the interest of the American people and should transcend the boundaries of political parties. Both reports are starting points for the formulation of policies which must be continuously revised to meet changing conditions. Regardless of the outcome of the election the principles embodied in these two great documents must be kept alive. The Paley report is right in our own bailiwick of mineral raw materials and it behooves us to study it carefully as our responsibility to posterity. To those in the mining industry who have limited their field of observation to moving rock or to metal prices it may come as a surprise that our production of such staples as copper, lead, and zinc has fallen behind increased requirements to the point that substantial tonnages must be imported. Iron ore is next on the list and everybody knows that such metals as tin, tungsten, chromium, manganese, nickel, and cobalt are imported almost exclusively. The crisis in raw materials pointed up by the Paley report has been reported annually by Elmer Pehrson and others to small gatherings at the Mineral Economics Division sessions at the Annual Meeting for as long as we can remember. In September 1949, the United Nations Economic and Social Council held an international resource conference at Lake Success which disclosed these same grave conclusions: - Consumption of raw materials is multiplying at an alarming rate, faster than discoveries or replacements are being made. - Production has been wasteful and utilization lavishly beyond enginee¬ing and practical requirements. - Industrialized nations are depleted and many raw materials consumed by industry are not found in the industrialized countries. - Nations formerly exporters of raw materials are increasingly building their own consuming industries. - Political forces in the world are limiting access to raw materials. The Paley Commission selecting the quarter century, 1950 to 1975, to project raw material requirements for the United States, pointed out obstacles to meeting these requirements, and made recommendations for procurement. It is not important that we disagree that cobalt consumption will reach 344 pct of present, or fluorspar 187 pct when iron and ferroalloys are only expected to increase 75 pct. What is important it that the fabulous appetite of the United States for mineral raw materials has consumed more since World War I than was consumed by the entire world in all recorded history prior to 1914. And, unless the people of the United States are satisfied to remain at their present standard of living (which is unthinkable) this consumption is correctly plotted by the Paley Commission as continuing to expand. If the U. S. is to continue on a course of progress, it must procure raw materials wherever it can at the lowest possible cost. Natural resources are clearly an area in which the broadest cooperation between industry and government must exist to achieve efficient exploitation, economic consumption, and expansion of sources of supply. The message of the Paley report requires action comparable to that of the North Atlantic Pact. Its implication is as significant as military preparedness. It is a world problem. It is a mining engineering problem. Don't let it die!

Jan 1, 1952

By Amos P. Brown

PYRITE, the bisulphide of iron, FeS2, is found more or less in all coal-beds: but, as a rule, in certain definite forms. More than any other impurity, it detracts from the commercial value of a coal-deposit, and yet its presence is so universal that it might almost be said that there is no coal entirely free from pyrite. My observation has been confined to the Pennsylvania bituminous and semi-bituminous coals, and to them, therefore, my remarks will be confined. Certain generalizations which I may make, however, will be found of universsl application. The lowest members of the coal-formation, No. XIII. of the Pennsylvania bituminous region, are nearly always pyritiferous, and in many cases highly so. In Cambria county, for instance, coalbed A, the Brookville, is locally known as the " Sulphur seam." The Lower Kittanning, in parts of Clearfield county, is so sulphury as to be almost unmarketable, though otherwise it is a strong locomohive coal. In Mercer county the Pardoe bed, so extensively mined there, carries great quantities of sulphur in the form of pyrite, though usually this can be separated in such a way as to detract little from the market-value of the coal. The other coal-beds of the Lower

Jan 1, 1888

By Henry D. Hibbard

Henry D. HibbaRd, Pittsburgh, Pa,: This is a most interesting and instructive paper, some of whose lessons should find immediate application. It points out how fuel-consumption is to be decreased in open-hearth practice, by changes in the plan of the furnace. To look first at the greatest item of loss, radiation, it is seen that thicker brick-work is advisable to lessen this. Especially is this true of the roof, made at present, almost universally, only 9 inches thick to prevent cutting. Now that high roofs, well above the course of the flame, are becoming general, and the average melter is better able to judge the temperature of his furnace, that reason has less force; and we may build roofs 18 inches thick, or perhaps better cover the usual 9 inches with an equivalent layer of sand, which has the advantage of following the arch as it rises and falls with the different degrees of heat. The side-walls of the hearth, usually 131/2 inches thick, may also he thickened up to 18 inches, and the door-linings to 7 inches; and the heat thereby saved will be valuable, while its absence from the working-platform will be much appreciated by the workmen.

Jan 1, 1892

By G. F. Tagg

EARTH-REISTIVITY measurements are often of service in obtaining information regarding geological formations, particularly when applied to structural problems. In such problems the masses of the various bodies are large, and have a corresponding effect on the average resistivity of the soil. Much work has been done using such measurements, but in general the method of interpretation employed is empirical. Since certain simple cases can be investigated mathematically, it appears to be quite sound to endeavor to apply the mathematical solutions to the practical results, in order to deduce from the latter such unknown quantities as depth. This paper deals with such a method of interpretation for the simple case of a single horizontal stratum. SURFACE Of EARTH In the method described by FIG. 1.-WENNER'S METHOD OT MEASURING Wenner1 for measuring earth resis- EARTH RESISTIVITY. tivity, four stake electrodes are driven into the earth in a straight line as shown in Fig. 1. A current I amperes is passed between the two outer stakes and the potential difference . V volts between the two inner stakes is measured. Then if a is the electrode separation, the specific resistance of the soil, which is assumed to be homogeneous, is given by the formula

Jan 1, 1932

By C. H. Jr. Herty

IT Is well known that manganese will desulfurize molten iron through the formation of manganese sulfide, which, being only slightly soluble in the metal, rises to and enters the slag where it remains as such (mixer slag) or is converted partly or wholly to calcium sulfide (basic open¬hearth slag). The reaction by which manganese sulfide is formed is Mn + FeS = MnS + Fe. This reaction is generally considered to be reversible, although McCance1 states- that such is not the case. The experimental work was carried out to confirm the results of Rohl2 as to the reversibility of the reaction. Six trials are herein considered. In each 200 grams of electrolytic iron free from manganese and sulfur were melted in a pure zirconia crucible in a carbon resistance electric furnace. To the melted iron in runs 2, 3 and 4 metallic manganese and manganese sulfide were added to give 1, 2 and 4 per cent. manganese respectively, with 0.50 per cent. of sulfur in each. In runs 5, 6 and 7, metallic manganese andiron sulfide to give the same proportions of manganese and sulphur as in runs 2, 3 and 4, were added. The melts were held molten in the furnace for an hour and then cast into small ingots.

Jan 2, 1925

By Ingvar Janelid

DURING the last ten years, in the effort to save manpower and costs, methods of drilling and blasting in Sweden have changed and developed in a revolutionary manner. These developments have been accompanied by extensive alterations in methods of tunneling and in mining technique. Since the end of the 1940's there has been a 100 pct change-over in Sweden to the use of tungsten carbide tipped drill steel. Both investigations and practical results have shown clearly that a tungsten carbide chisel bit fastened directly on the drill steel is the most economical for Swedish conditions. This applies to drill steel up to the longest size it is practical to handle. In terms of drilling footage, durability of the drill steel and the tungsten carbide bit is generally the same. In this respect, therefore, a detachable bit offers no advantage over integral steel. Transportation of integral steel to the grinding plant, instead of detachable bits only, involves heavier work, but this is counteracted by placing grinding plants closer together or by grinding at the working place itself. The drilling rate with integral steel is higher, the trouble of changing bits is avoided, and the difficulties which always arise with joints are eliminated.

Jan 6, 1954

By Robert Mehl

METALLURGISTS are properly interested in papers dealing with subjects ranging from the theories of the metallic state to very practical details on the use of metals. A review of theoretical metallurgy naturally excludes papers concerned with the usefulness of metals and limits itself to those concerned purely with the science of metals. Even in this more limited field the reviewer is confronted with thousands of papers dealing with facts and theories of metallic behavior, from which he can select only a few hundred. The selection is necessarily highly arbitrary. Certain classes of papers definitely fall within the scope of this review. Thus, papers on the deformation of metals, on the structure of alloys, on recrystallization, to select only a few, are fully represented. Other subjects, which verge on what is generally accepted as the science of metals, such as the magnetic properties of metals, the less familiar electrical properties and theories, adsorption of gases by metal surfaces, and the like, are treated scantily. Particular attention is given to reviews of subjects that fall with in the groups chosen; in a summary such as this, which is largely in the nature of a progress report, capably written reviews are of importance, particularly since the monograph and text book literature is so meager in this field.

Jan 1, 1935

By Robert Mehl

METALLURGISTS are properly interested in papers dealing with subjects ranging from the theories of the metallic state to very practical details on the use of metals. A review of theoretical metallurgy naturally excludes papers concerned with the usefulness of metals and limits itself to those concerned purely with the science of metals. Even in this more limited field the reviewer is confronted with thousands of papers dealing with facts and theories of metallic behavior, from which he can select only a few hundred. The selection is necessarily highly arbitrary. Certain classes of papers definitely fall within the scope of this review. Thus, papers on the deformation of metals, on the structure of alloys, on recrystallization, to select only a few, are fully represented. Other subjects, which verge on what is generally accepted as the science of metals, such as the magnetic properties of metals, the less familiar electrical properties and theories, adsorption of gases by metal surfaces, and the like, are treated scantily. Particular attention is given to reviews of subjects that fall with in the groups chosen; in a summary such as this, which is largely in the nature of a progress report, capably written reviews are of importance, particularly since the monograph and text book literature is so meager in this field.

Jan 1, 1935

By M. A. Orehoski, J. M. Hodge

It is now generally conceded that if a steel is to develop optimum physical properties in the conventionally quenched and tempered condition, the microstruc- ture after quenching should consist wholly of martensite; and that transformation of austenite to intermediate-temperature products during quenching will have a deleterious effect upon the physical properties, particularly the toughness, of the tempered material. This implies that, in order to obtain the optimum physical properties from a given steel, its "harden-ability " should be high enough to suppress all transformation except that to martensite under the heating and quenching conditions to which it will be subjected, and this premise is probably the most important reason for hardenability control. However, the criterion of hardenability that at present is most widely accepted and used is based on a microstructure of 50 per cent martensite. This criterion, which was suggested by Grossmann,' does have considerable justification. It may be readily measured by a fracture or etch test and, since it represents the point at which the hardness is changing most rapidly with variations in cooling rate, it may be determined empirically from a hardness-depth curve by determining the point of steepest slope (the inflection point). Furthermore, in plain carbon steels or in steels of low hardenability, the difference in hardenability expressed in

Jan 1, 1947

By J. M. Hodge, M. A. Orehoski

It is now generally conceded that if a steel is to develop optimum physical properties in the conventionally quenched and tempered condition, the microstruc- ture after quenching should consist wholly of martensite; and that transformation of austenite to intermediate-temperature products during quenching will have a deleterious effect upon the physical properties, particularly the toughness, of the tempered material. This implies that, in order to obtain the optimum physical properties from a given steel, its "harden-ability " should be high enough to suppress all transformation except that to martensite under the heating and quenching conditions to which it will be subjected, and this premise is probably the most important reason for hardenability control. However, the criterion of hardenability that at present is most widely accepted and used is based on a microstructure of 50 per cent martensite. This criterion, which was suggested by Grossmann,' does have considerable justification. It may be readily measured by a fracture or etch test and, since it represents the point at which the hardness is changing most rapidly with variations in cooling rate, it may be determined empirically from a hardness-depth curve by determining the point of steepest slope (the inflection point). Furthermore, in plain carbon steels or in steels of low hardenability, the difference in hardenability expressed in

Jan 1, 1947

By Arthur Fleischer

The Kalunite process+ for the production of metal-grade alumina from alumina-con-taining ores is applicable, considered from a general point of view, to any aluminous raw material that can be converted to potassium alum or equivalent normal alum. This result of modern technology has been the subject of a continuous study and development since 1929, on a laboratory and test-plant scale, with initial emphasis on the utilization of alunite as the raw material. The research and developmental program was carried out by the Kalunite Company and its successor, Kalunite, Inc., an affiliate of the Olin Corporation of East Alton, Illinois. The process is now approaching the time for a major test in its history with the completion of construction of a plant having a capacity of IOO tons of alumina per day in Salt Lake City for the conversion of Marysvale, Utah, alunite ores to alumina and potassium sulphate. The Salt Lake Alumina Plant is a Defense Plant Corporation project. Production of Aluminum: The known existence of alunite deposits, especially in the Marysvale district, furnished the motive for the original inquiry into the utilization of this raw material for aluminum production. The deposits in this region were actively explored during World War I and utilized for the production of potassium sulphate, an essential fertilizer, of which a shortage of monumental proportions then existed. Up to the twentieth century—for alunite is a mineral with an ancient history—it was used in Europe and in China as a source of potassium alum. It never had been used successfully in this country as a source of oxide for reduction to metal. Although the known reserves of this ore, which undoubtedly will be greatly expanded with a commercial outlet for this ore, are recognized to be sufficient for only a part of the present-day needs of aluminum, it has a definite place in the aluminum industry. Academically it points the way for future raw materials. The aluminum industry has undergone a remarkable growth in the past few years as a result of defense and war requirements. Its expansion in many ways has been beyond belief and prediction, both in volume and location. This wartime status of the industry has accelerated the consumption of bauxite to such an extent that a re-evaluation of the raw material reserves for the future peacetime industry and for eventual wartime reserves is seemingly of concern. The generally accepted picture of bauxite ore reserves in the United States, especially in raw material suitable for treatment by the Bayer process, focuses attention on other possible sources of raw material of metal-grade oxide. The perspective for the development of a suitable process may have changed in the interim since the original work by Kalunite, but the ultimate goal is the same.

Jan 1, 1944

By L. J. Demer, W. W. Walker

AMONG several variables of the indentation hardness test is the effect of loading time on the measured hardness of a material. The most generally recommended duration of loading is 10sec.1-3 Although this short loading duration is undoubtedly satisfactory for harder metals, it is questionable that it is sufficient for very soft metals,4 or for certain plastics.5 The effect of duration of loading on the measured hardness of ionic crystals is largely unknown, although Onitsche and Mitsches found that the indentor (under a very low load) had not yet reached equilibrium after 60 sec in a variety of ionic crystals. To extend further the data of Onitsche and Mitsche, a systematic study was made of the effect of duration of loading for longer periods, up to 50,000 sec, on the 136 deg Dph of synthetic lithium fluoride. For comparison, less extensive tests were made on synthetic magnesium oxide and copper single crystals. The general procedure used was to indent a cleaved and polished (100) face of a lithium fluoride crystal using a Leitz Durimet microhardness tester. In certain cases, the indentor was so oriented as to align the diagonals of the 136 deg diamond pyramid indentation parallel to a (100) edge. In other cases the diagonal of the indentation was aligned at 45 deg to a (100) edge of the crystal. After indenting, the surface tested was etched in the acid etchant recommended by Gilman and Johnston.' This revealed the position of dislocation lines which intersected the surface tested. At these points of emergence were formed the usual sharp, pyramidal etch pits as shown in Fig. 1. The specific procedure used in studying duration of loading was as follows. The surface of the crystal was indented, and the load was left on the indentor for a predetermined time. This duration of loading was varied systematically from 1 to 50,000 sec. After the desired amount of time had elapsed, the indentor was removed from the crystal and the size of the resulting indentation was determined using a micrometer eyepiece. The surface was then etched to reveal the dislocation etch pit pattern around the indentation. Procedures used for lithium fluoride, magnesium oxide, and copper were similar. Preliminary studies revealed that, although an indentation was enlarged by increasing loading time, no corresponding changes occurred in the surface etch pit pattern. Since no evidence of dislocation movement was observed on the surface, it was assumed that the plastic deformation indicated by the indentor sinking into the surface was a result of dislocation movement inside the crystal. This movement was studied bf making a series of surface indentations in a crystal corresponding to various lengths of time, cleaving the crystal vertically through the indentations, etching the freshly

Jan 1, 1964

By S. Leber, R. F. Hehemann

This investigation describes the kinetics of alloying in a (Cb-15 wt pct W. 5 wt pct Mo, 1 wt pct Zr) powder-metallurgy alloy. The degree of homogeneity obtained in hydrostatic ally pressed and vacuum-sintered samples is described by composition distributions resulting from analysis of X-ray dvfraction line profiles. Sintering variables and degvee of powder dispersion were evaluated. The utility of single-value parameters obtained from composition distributions is disaissed. The spatial distribution of composition, as revealed by anodically tinted metallographic sarrzples, was used to provide diffision models based on a concentric-sphere geometry. Diffusion equations developed from these models were found to be in general agreement with experimental results. The powder-metallurgy method for the production of refractory metal alloys has the ability to produce an inherently fine-grained, fabricable structure. The more general use of this method is inhibited, in part, by the presumed difficulty in obtaining homogeneity on a microscale. The degree of homogeneity therefore is an important, but usually neglected, variable in specifying the quality of a powder-metallurgy alloy. Convenient techniques for measuring the degree of homogeneity are now available,' and have been used to develop a model describing the process of alloying in a simple binary mixture.' In this investigation, the process of alloy formation has been studied in a more complex system. PROCEDURE The columbium-based F-48 mixture was prepared from the constituent powders shown in Table I. The particle sizes tabulated were provided by the vendors of the individual powders. Standard laboratory techniques utilizing a jar mill were employed for blending. The blended powders were hydro-pressed into 1-in. diam rods which were then sliced into thin discs for vacuum sintering. All samples were given a preliminary treatment at 1700°C for 2 hr. Varying degrees of homogeneity were obtained using additional treatments at higher temperatures. The degree of homogeneity obtained by a specific sintering treatment was evaluated metallographi-cally using the anodic-tinting technique described by olff,' and quantitatively by the analysis of X-ray diffraction line profiles using the X-ray diffraction technique developed by udman.' The diffraction technique is strictly valid only for binary systems. However, the relatively small difference between the lattice parameters of tungsten and molvbdenum when compared with columbium permitted the treatment of the complex composition of F-48 as a (W, Mo)-Cb pseudobinary. Calculations were weighted in accord with the W-Mo ratio in the F-48 composition. The contribution of the 1 pct Zr was ignored since it could not even be detected in the blended powder. Two factors are required to convert an X-ray line profile into a composition distribution. The variation of these factors with composition is shown in Fig. 1. Curve A was used to convert angular posi-

Jan 1, 1964

By John W. Vanderwilt

The fluorescence of scheelite has been an important aid in recent years in the discovery and development of scheelite deposits. The use of fluorescence of synthetic compounds in industry, particularly in advertising, also has expanded greatly during the past decade. As a result, a number of new and convenient units for producing ultraviolet energy have become available, which have led to a greater application of fluorescence in the study of minerals. Studies have shown that the fluorescent color of a mineral may vary: (I) with the kind and quantity of trace elements, and (2) with the particular wave length of ultraviolet energy used. The wave length is dependent first on the type of generating equipment used, and finally on the filter employed to remove the visible light that may be present. A number of so-called ultraviolet lamps are listed and described, together with suitable filters known to be available. Scheelite fluoresces brilliantly with wave lengths of 2200 to about 3000Å., but not with longer wave lengths. The most convenient and efficient sources of ultraviolet for scheelite fluorescence are portable and laboratory units designed particularly for use with scheelite. So-called ultraviolet light globes of the photo-flood type emit wave lengths too long to cause scheelite to fluoresce. Attention is called to the minerals that fluoresce in a manner similar to scheelite, which necessitates a check test by means of characteristic physical properties. Chemical tests are the final authority both for identity and content of tungsten in scheelite ore. Introduction Recent development and extensive use of fluorescent lighting make it unnecessary to explain what fluorescence looks like. The fluorescent light tube is in reality a mercury vapor arc, which generates ultraviolet energy. Coating the inside walls of the tube is a substance, called a phosphor, that converts the ultraviolet rays to visible rays of light. In a like manner, certain minerals will transform ultraviolet energy to visible rays of various colors. The phenomenon of brilliant fluorescent colors cannot be satisfactorily described or reproduced photographically; a display must be seen to be appreciated. Only a few years ago fluorescence was regarded primarily as a source of entertainment, chiefly in spectacular displays of specimens in museums. The brilliant fluorescence of willemite, a zinc ore mineral, at Franklin, New Jersey, was utilized quite early in checking the efficiency of certain milling operations. Fluorescence has been used extensively in exploring for scheelite, as well as in mining this ore, during the past 10 years. The use of fluorescence in detecting scheelite, an important tungsten ore mineral, is well established, and much success has attended this new method; scheelite is a very inconspicuous white to gray mineral in ordinary light, but it

Jan 1, 1949

By John W. Vanderwilt

The fluorescence of scheelite has been an important aid in recent years in the discovery and development of scheelite deposits. The use of fluorescence of synthetic compounds in industry, particularly in advertising, also has expanded greatly during the past decade. As a result, a number of new and convenient units for producing ultraviolet energy have become available, which have led to a greater application of fluorescence in the study of minerals. Studies have shown that the fluorescent color of a mineral may vary: (I) with the kind and quantity of trace elements, and (2) with the particular wave length of ultraviolet energy used. The wave length is dependent first on the type of generating equipment used, and finally on the filter employed to remove the visible light that may be present. A number of so-called ultraviolet lamps are listed and described, together with suitable filters known to be available. Scheelite fluoresces brilliantly with wave lengths of 2200 to about 3000Å., but not with longer wave lengths. The most convenient and efficient sources of ultraviolet for scheelite fluorescence are portable and laboratory units designed particularly for use with scheelite. So-called ultraviolet light globes of the photo-flood type emit wave lengths too long to cause scheelite to fluoresce. Attention is called to the minerals that fluoresce in a manner similar to scheelite, which necessitates a check test by means of characteristic physical properties. Chemical tests are the final authority both for identity and content of tungsten in scheelite ore. Introduction Recent development and extensive use of fluorescent lighting make it unnecessary to explain what fluorescence looks like. The fluorescent light tube is in reality a mercury vapor arc, which generates ultraviolet energy. Coating the inside walls of the tube is a substance, called a phosphor, that converts the ultraviolet rays to visible rays of light. In a like manner, certain minerals will transform ultraviolet energy to visible rays of various colors. The phenomenon of brilliant fluorescent colors cannot be satisfactorily described or reproduced photographically; a display must be seen to be appreciated. Only a few years ago fluorescence was regarded primarily as a source of entertainment, chiefly in spectacular displays of specimens in museums. The brilliant fluorescence of willemite, a zinc ore mineral, at Franklin, New Jersey, was utilized quite early in checking the efficiency of certain milling operations. Fluorescence has been used extensively in exploring for scheelite, as well as in mining this ore, during the past 10 years. The use of fluorescence in detecting scheelite, an important tungsten ore mineral, is well established, and much success has attended this new method; scheelite is a very inconspicuous white to gray mineral in ordinary light, but it

Jan 1, 1949

By AIME AIME

In the uniform of his country for the second time, Harry Phillip Stolz. Chairman of the A.I.M.E. Petroleum Division, holds a commission as Lieutenant-Commander in the Naval Reserve and is attached to the office of Inspector of Naval Petroleum Reserves in California. During World War I he left his studies at Stanford University to join the Army and was granted a commission as Second Lieutenant of Infantry. He remained in the Army Reserve until 1938 when he resigned to accept a commission as a member of the Naval Petroleum Reserves Advisory Board. Born in San Francisco Jan. 29,1899, where his father had lived since 1880, he was in that city during the turbulent year of 1906 where the city was ravaged by fire and earthquake.

Jan 1, 1942

Jan 1, 1966

By Frank G. Miller, Ralph A. Seban

Problems relating to thermal methods of oil recovery have been given increasing attention during the past year. The nature of the physical and chemical processes underlying thermal recovery are not yet well understood. The need for pertinent basic information is recognized generally. One of the processes involved is the transfer of heat by conduction in oil reservoir rocks containing moving reservoir fluids. This technical note deals with heat conduction in a laboratory sand column filled with a moving hydrocarbon and therefore should be contributory to the presently inadequate fund of knowledge on thc over-all subject. In an analysis of the flow of vaporiziny propane through a horizontal column of sand, one of the present author9 demonstrated correspondence between thc measured values of pressure along the length of the column and those predicted by a theory which postulated that the enthalpy of the propane was invariable along the length of the column. This postulate way implied as a deduction from the principle of conservation of energy but the details of the deduction were not given. The specific purpose of this technical note is the presentation of these details both as an adjunct to the earlier analysis and to supply some additional details on the processes involved in this type of flow. Results disclose that rates of heat transfer by conduction, in the direction of fluid motion, generally would be small for systems of the type studied. FUNDARIENrAI. ENERGY EiQUAI-[ON The principle of conservation of energy may be applied to a section of the porous material on the basis that heat transfer, like fluid flow, is possible in the x direction only. Transfer of heat in the y and z di'rections is prevented by suitable insulation or by taking the medium as infinite in directions perpendicular to the x axis. For steady state heat conduction and conditions of steady fluid flow the principle of conservation of energy specifies that any reduction in the enthalpy rate increases the flow of heat in the same proportion. Stated mathematically, dH KA 87 —- = - — - — U) * dx W dx........ Lvhere is the flow of heat in the positive x W dx direction. TEMPERATURE DISTRIBUTION IN DIRECTION OF FLOW The column of sand used in the previoi~sly described research is divisible into three different flow regimes. each of which may be analyzed independently. In the entrance region the liquid approaches the saturation state. A transition region is postulated following the transverse section at which the saturation state of the liquid is attained. In this transition region gas and liquid phases are both envisioned as present, with no vaporization occurring and with fluid movement restricted to the liquid. The upstream end of the exit region is at the transverse section of the column where the fraction of the pore space occupied by gas first becomes great enough for gas flow and where vaporization of the liquid begins. Fig. 1 indicates schematicaHy the thermodynamic processes undergone hv the fluid in the three flow regimes.

Jan 1, 1956