Search Documents

By T. A. Klinefelter, Glenn C. Truesdell, Richard W. Smith, R. G. Meara, O&apos

The investigation of domestic talcs was undertaken by the Bureau of Mines, Department of the Interior, in cooperation with the University of Alabama, at the request of the U. S. Army, on Dec. 1, 1941: "Considerable concern has been expressed by the Supply Arms and Service over maintaining continued availability of supplies of the necessary raw materials. These ceramic products are used by the Signal Corps in all army radio equipment, and to a greater degree in the new ultra-high-frequency equipment. The Air Corps has become a user of large amounts of radio-grade ceramics for' aircraft spark-plug covers required for high-altitude operations. In addition, the use of this material is essential to the proper functioning of the radio air-navigation aids of the Civil Aeronautics Board." History The use of steatite and talc in ceramic bodies goes back a great many years. If pure, talcs shrink little under heat-treatment and are very resistant to heat shock. The massive form, commonly called "steatite" by the trade, cuts and works easily, and this was naturally the first method used in obtaining articles of talc. When gas was in general use for illuminating purposes, a. large business was carried on in the manufacture of tips for gas burners.' With the development of uses for electricity, low-tension insulators were made in a similar manner; and, in fact, the forming of shapes from massive talc continues. However, as the business increased, cuttings and waste became more and more of a problem. In the twenties, one of the larger producing firms had a cooperative agreement with the Bureau of Mines at its Columbus station to work out a body using the finely powdered material. Somewhat earlier, manufacturers of spark plugs used the finely ground talc as part of the body and to some extent in wall-tile bodies. Somewhat later it came into use for kiln furniture and similar products and still more recently it has been used in some dinnerwares. With the development of the radio and the high-frequency fields generated, it was found that a dense steatite porcelain was far better than even high-tension electrical porcelain, which is a clay-flint-feldspathic type of body. Until the war increased the demand, the several pioneer steatite-porcelain manufacturers were able to furnish adequate supplies. When war began in Europe and Asia, three important foreign sources of raw material were cut off; i.e., the French, Italian, and Man-churian talcs. Domestic producers of high-grade porcelain are few, and the trade

Jan 1, 1948

Apparatus and a method for determining the volumetric behavior of hydrocarbons at pressures up to 10,000 psia and at temperatures between 0° and 460°F are described. The equipment is suitable for measuring the total volume of the system and the volume of a liquid phase as functions of state within these ranges of temperature and pressure. Introduction During the past two decades there has been a marked increase in the ranges of temperature and pressure encountered in underground hydrocarbon reservoirs of commercial interest. In addition, greater interest in the intensive characteristics of the fluids found in these reservoirs has developed. Apparatus Several types of apparatus have been developed in the authors' laboratory for volumetric measurements of hydrocarbon systems. The earliest equipment described1 was characterized by constant volume, and the weight of material present was varied systematically in order to attain the different pressures desired in the study. Later another apparatus2 was built in which the effective volume of the cylindrical cell, which confined a hydrocarbon sample of constant weight was varied by injection or withdrawal of mercury. The effective total volume of the equilibrium cell was measured by ascertaining the position of the mercury surface but no measurement could be made which gave knowledge of the volumes of individual phases existing within the hydrocarbon system. A third apparatus3 was designed for use at higher pressures and temperatures than the earlier equipment would tolerate. This apparatus was of the variable volume type but was built in the general form of a U-tube, the mercury level being measured at the surface which was not exposed to the hydrocarbon system. This arrangement avoided the need of subjecting measuring equipment to the extremes of temperature at which studies were made, but it gave no provision for measurement of the volumes of individual phases. Although this last apparatus was satisfactory as to accuracy and convenience for many purposes, need was felt for measurements of the volume of the liquid phase of the hydrocarbon system. For this reason a fourth equilibrium apparatus was designed and constructed, and it is the purpose of the present paper to describe it. The equilibrium cell has a working range of temperature from 0° to 460°F at pressures up to 10,000 psi. Provision for measurement of both total volume and liquid-phase volume makes it particularly suitable for the equilibrium study of heterogeneous systems consisting either of simple mixtures or of complex field samples of hydrocarbons. The general arrangement of the ap-

Jan 1, 1948

AT the meeting of the Board of Directors held on June 25, 1926, and in response to numerous in-dividual suggestions for changes, a committee on Re-vision of the Constitution and By-Laws of the Insti-tute was appointed, consisting of C. F. Rand, Archi-bald Douglas and H. Foster Bain. Various confer-ences were held, much correspondence conducted and a preliminary draft was prepared. It proved imprac-ticable to complete the work in time to submit the matter to the membership for approval or disapproval at the annual meeting in 1927, and the Committee was continued with instructions to prepare a report as a basis of action in 1928. After Mr. Rand's death George Otis Smith was appointed in his place and the tentative draft herewith submitted has been pre-pared in its present form by Messrs. Smith, Douglas and Bain, though not differing in any material mat-ter from an earlier draft approved by Mr. Rand. In preparing this the Committee has kept in mind primarily the desirability of simplification and of making the By-Laws conform to the actual practice of the Institute as worked out through experience. The Constitution and By-Laws adopted in 1912, and which with minor amendments only still govern the Insti-tute, are full of specific provisions regarding pro-cedure; such as that laid down for guidance of the Papers and Publications Committee. Many of these have proved unworkable and in practice have not been always strictly followed. It now seems wise to write into the Constitution and By-Laws only the general fun-damental principles to he followed and to provide for such easy change in methods of following them out as will permit efficient conduct of the business. It is this thought that has guided the Committee in rewrit-ing many of the sections. With this in view also the Constitution, as such, has been shortened to the brief-est feasible statement of fundamentals. All matters relating to means of making these principles effec-tive have been put into the By-Laws or in the hands of committees whose work is subject to control and whose rules are subject to approval or disapproval by the Board of Directors. Many suggestions for changes have come to the Committee that have not been incorporated in this draft. Some of these are in themselves excellent but have not been incorporated here because the Commit-tee discovered no sentiment for them such as would be likely to secure their approval, or found them out of harmony with the general plan followed herein.

Jan 9, 1927

Apparatus and a method for determining the volumetric behavior of hydrocarbons at pressures up to 10,000 psia and at temperatures between 0° and 460°F are described. The equipment is suitable for measuring the total volume of the system and the volume of a liquid phase as functions of state within these ranges of temperature and pressure. Introduction During the past two decades there has been a marked increase in the ranges of temperature and pressure encountered in underground hydrocarbon reservoirs of commercial interest. In addition, greater interest in the intensive characteristics of the fluids found in these reservoirs has developed. Apparatus Several types of apparatus have been developed in the authors' laboratory for volumetric measurements of hydrocarbon systems. The earliest equipment described1 was characterized by constant volume, and the weight of material present was varied systematically in order to attain the different pressures desired in the study. Later another apparatus2 was built in which the effective volume of the cylindrical cell, which confined a hydrocarbon sample of constant weight was varied by injection or withdrawal of mercury. The effective total volume of the equilibrium cell was measured by ascertaining the position of the mercury surface but no measurement could be made which gave knowledge of the volumes of individual phases existing within the hydrocarbon system. A third apparatus3 was designed for use at higher pressures and temperatures than the earlier equipment would tolerate. This apparatus was of the variable volume type but was built in the general form of a U-tube, the mercury level being measured at the surface which was not exposed to the hydrocarbon system. This arrangement avoided the need of subjecting measuring equipment to the extremes of temperature at which studies were made, but it gave no provision for measurement of the volumes of individual phases. Although this last apparatus was satisfactory as to accuracy and convenience for many purposes, need was felt for measurements of the volume of the liquid phase of the hydrocarbon system. For this reason a fourth equilibrium apparatus was designed and constructed, and it is the purpose of the present paper to describe it. The equilibrium cell has a working range of temperature from 0° to 460°F at pressures up to 10,000 psi. Provision for measurement of both total volume and liquid-phase volume makes it particularly suitable for the equilibrium study of heterogeneous systems consisting either of simple mixtures or of complex field samples of hydrocarbons. The general arrangement of the ap-

Jan 1, 1948

By D. C. Hilty, W. Crafts

The solubility of oxygen in iron containing aluminum has been determined at 1550°, 1600°, and 1650°C and found to be much higher than predicted from theoretical considerations, possibly due to equilibria with an iron-aluminum spinel phase rather than pure AI,O.. The presence of manganese greatly increased the deoxidizing power of aluminum. DEOXIDATION and inclusion formation in steel have proved to be elusive phenomena that are difficult to control in spite of much effort to understand and evaluate the reactions. Study of the problem indicated that more accurate data on the solubility of oxygen in iron containing deoxidizers were essential to further progress, and an empirical determination of oxygen solubilities has been initiated at the Union Carbide and Carbon Research Laboratories, Inc. The investigation has included the effects of aluminum, silicon, manganese, and combinations of these elements at 1550°, 1600°, and 1650°C. The equipment and experimental procedure as well as the results of a study of the effects of aluminum are described below. In general, it was found that the solubility of oxygen in iron containing aluminum is much higher than predicted, possibly because of the formation of complex nonmetallic phases, and that manganese greatly increases the deoxidizing power of aluminum. The generally accepted deoxidation curves for 1600°C are summarized in fig. 1, from "Basic Open Hearth Steelmaking"'. These curves are assumed to represent the solubility of oxygen in the presence of deoxidizers and should indicate the limits of mis-cibility gaps in the phase diagrams of the systems that control the formation and character of non-metallic inclusions as described by Benedicks and Lofquist'. They were derived mainly by application of the methods of thermodynamics to the available experimental observations, and by calculations based on the thermal constants of the pure substances when experimental data were lacking. Among the more notable researches contributing to the development of knowledge of oxygen solubilities are those of Korber and Oelsen8, 4, C. H. Herty, Jr. and associates5,6, Krings and Schackmann7, Went-rup and Hieber8 Schenck and Briiggeman9, Vacher and Hamilton'" and Chipman and co-authors 1,11,12,13 Practically, the deoxidation curves are of limited value in predicting oxygen content and rationalizing deoxidation practices. The reasons for this inadequacy appear to be error from inaccurate data, oversimplifying assumptions, interacting effects of combined deoxidizers, and possibly unknown extra-equilibrium and side reactions. Although inclusion formation is a very complex reaction it must be re-

Jan 1, 1951

SEC 1 The membership of the Institute shall comprise seven classes, namely 1 Members, 2 Honorary Members, 3 Senior Members, 4 Associates, 5 Junior Members, 6 Rocky Mountain Members, 7 Junior Foreign Affiliates All shall be equally entitled to the privileges of membership, excepting that no member of any class whose residence shall be outside of the United States of America, except those residing in Mexico and Canada, shall be entitled to vote SEC 2 Members A person to be eligible for election or transfer into the class of Member must be at least 27 years of age and must have had at least six years' employment in the practice of engineering, mining, geology, metallurgy, or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields This shall not apply to Rocky Mountain Members SEC 3 Honorary Members Each candidate for Honorary Membership must be recommended by the Committee on Honorary Memberships and must be elected by ballot at a meeting of the Board of Directors by the unanimous vote of the Directors present, provided, however, that the number of Honorary Members shall at no time exceed twenty Such election shall automatically act as a transfer of such member from any other class of membership to which he may belong SEC 4 Senior Members The Directors may, at the special request of any Member or Associate who has reached the age of seventy years and who has paid

Jan 1, 1952

By Ripu Daman Lama

The size of coal pillars in mines until recently has been determined by experience without being based upon scientific investigations. As a consequence, the size of pillars had invariably been larger than could be accounted for because of the number of unknown factors involved which influence the strength, dictating the use of large safety factors. With the mining going deeper, the size of the pillars greatly increases and sometimes a considerable portion of the mineral property are blocked in the mine pillars required to support the superincumbent strata. With the advances in the field of Rock Mechanics, attention of mine planning engineers has been focused upon the design of mine pillars for safe and efficient working as well as decrease losses of coal. The problem involves the study of three factors: (1) Presence of stresses in the area and their distribution on pillars in the course of extraction. (2) The influence of external factors on the strength of coal. (3) The inherent mechanical properties of coal. These aspects have been studied by a large number of investigators, the first by in-situ stress measurements and photoelastic studies and the second and third aspect by studies conducted in the laboratory on small size specimens (Bunting, 1911; Evens & Pomeroy, 1961; Gaddy, 1956; Greenland et al, 1941; Steart 1954). The size of the specimens tested in the laboratory has been limited to a few inches and the results obtained have been extrapolated by large factors, sometimes several hundred times the largest specimen tested. In these tests much consideration has not been given to

Jan 1, 1971

By S. WHINERP

(Cleveland Meeting, October, 1912.) I AM indebted to L. E. Bryant, of Danville, Ky., President of the Virginia Mining Co., operating coal-mines in Scott county, Tenn., for the following information relating to the existence of the Clinton iron-ore under the NW. slope of the Cumberland Plateau in Kentucky and Tennessee. During the past 15 years quite an important oil-field has been developed in a region having Wayne county, Ky., as its center, and a large number of wells have been drilled in that and adjacent territory in the search for oil. Many of' these wells have been carried to considerable depths below the recognized oil-bearing horizon, and one of them was drilled by Mr. Bryant at Pine Knot, a station on the Cincinnati, New Orleans & Texas Pacific railroad, a few miles north of the point where that road crosses the Kentucky-Tennessee State-line. The elevation of the surface at the crossing is about 1,400 ft. above sea-level. The railroad is located on the dividing ridge between the Cumberland river and Big South Fork. At a depth of 1,720 ft. below the surface the drill reached and passed through a formation which the drillers called " red rock," but which Mr. Bryant classified as Clinton iron-ore, as its geological position corresponded to that formation. The ore at this point was 6 ft. thick and appeared to be of uniform quality throughout. An analysis of the drillings gave : Fe, 33; Mn, 0.25; Si02? 3 ; Al203, 2 ; CaO, 13; MgO, 7 ; P,05, 0.333 per cent. ; S, trace. This analysis seems to confirm the belief that the ore is Clinton, and that it is of a quality equal to the average of the deep or unbleached Clinton ores in Tennessee and Alabama. This discovery led Mr. Bryant to make further examinations and inquiries, and he found that the stratum called " red rock " by the drillers had been passed through and noted in the great majority of the wells carried down to the same geological hori-

Oct 1, 1912

By R. J. Schilthuis, T. V. Moore

In a previous paper,' the results of some experimental work on the measurement of slippage in the flow of oil and gas mixtures through vertical pipes were presented. The data obtained were correlated and equations were deduced from which the performance of the experimental gas-lift could be predicted with reasonable accuracy. However, attempts to apply the equations to the calculation of pressure drops in actual flowing wells yielded erroneous results. At the time the results of the experimental work were published, no satisfactory explanation could be offered for the failure of the empirical equations to express properly the performance of wells. However, recent work has led to the development of a new hypothesis which presupposes certain conditions affecting the flow of oil and gas in wells. When the proposed equations are corrected to allow for these conditions, an agreement between the observed and calculated performance of the actual wells is obtained which in most cases is quite satisfactory, although it is subject to certain limitations. In this paper, the method of calculating the pressure drop in actual wells is considered, and the application of the method to the design of tubing is discussed. (For nomenclature used in this discussion, see Table 1.) Factors Affecting Slippage and Efficiency At the outset, a few of the principle factors affecting slippage and efficiency in the gas-lift discussed in the previous paper will be reviewed. In the flow of the mixture of oil and gas in a vertical pipe, slippage is the phenomenon of gas moving upward with a. linear velocity greater than that of the oil. Under steady conditions, if given quantities of oil and gas enter the tubing per unit of time, the same quantities of oil and gas per unit time must, on the average, pass every section of the tubing; otherwise, there would be accumulation or depletion of the oil or gas at some sections, and the flow would be unsteady. Therefore, if the gas is to flow at a greater linear velocity than that of the liquid,

Jan 1, 1933

By R. F. Domagala, M. Hansen, D. J. McPherson

On the basis of metallographic analysis, incipient melting data, thermal analysis work, and X-ray diffraction, phase relationships in the 0 to 50 atomic pct alloy content were carefully resolved. Phase relationships in the higher alloy content regions were outlined. A single intermediate phase, peritectically formed, of the form ZrX2 was established in each system. A eutectic and a eutectoid were found in the zirconium-rich region of both systems. Appreciable solubility of molybdenum and wolfram was found in ß zirconium, but only a slight solubility in a zirconium. PREVIOUS work on these systems was limited to X-ray investigations of the intermediate phases1, 2 and preliminary surveys of the zirconium-rich alloys." The diagrams presented were determined principally by metallographic, thermal analysis, and incipient melting techniques. In accordance with the Atomic Energy Commission contract requirements, phase relationships up to 50 atomic pct molybdenum or wolfram were carefully resolved, while only a limited amount of work was done to outline the 50 to 100 atomic pct alloy region. A description and analysis of the metals used in the preparation of alloys for this study are included in Table I. A "low-hafnium" zirconium crystal bar, produced by the decomposition of a volatile iodide onto a hot filament, was employed for these studies. Westinghouse "Grade 3" crystal bar was used for all alloys. The zirconium, as received, was coated with corrosion product from a standard autoclave test by which its grade designation is determined. This was removed by a sand-blasting and HF-HNO, pickling technique developed by the Atomic Energy Commission. The bars were cold rolled to approximately 1/32 in. sheet, pickled for iron removal, sheared to 1/4 in. squares, washed with acetone, and stored for furnace charge. Molybdenum sheet. 0.003 in. thick, 0.001 to 0.005 in. wolfram wire, and M in. wolfram rod crushed to granular form, from Fansteel Metallurgical Corp., were used as alloying stock. Melting Procedure A nonconsumable electrode arc furnace identical to that described in detail by Hansen et al.4 was used. The source of power for melting Zr-Mo alloys was a 400 amp dc welding generator, while a 900 amp dc generator was used for preparing Zr-W alloys. Electrode tips of the same material as the alloy addition were employed in both systems, i.e., molybdenum tips were used for Zr-Mo alloys, and wolfram tips for Zr-W alloys. This precluded any possible electrode contamination during arc melting. Ingots of 20 to 30 g of Zr-Mo alloys were melted under high purity helium in the cavity of a copper block insert in a spun copper crucible. Homogeneity was insured by remelting all ingots four to six times without opening the furnace. Due to the large difference between the melting points of wolfram and zirconium, direct melting of the charged metals as above generally yielded ingots containing unmelted wolfram particles. This was overcome, after many variations in technique, by melting a pure wolfram charge at high power levels (700 to 900 amp) and slowly adding zirconium to form a master alloy. Such master alloys were sectioned and remelted several times, then crushed to serve as melting stock for alloys of lower wolfram content. Master alloys containing 26, 50, 52, 70, and

Jan 1, 1954

By J. B. DILWORTA

Ix estimating the investment-value of a mining-property or plant, the value of which decreases with operation, it is often necessary to know the sum which must be set aside periodically from earnings either to renew the plant at the end off its life, or to return the capital involved when the earning-power of the investment has ceased. In such cases it is manifestly incorrect simply to divide the total amount to be retired by the number of periods (usually years) during which the investment shall be active, as the sums periodically withdrawn have a certain interest-earning power varying with the length of time they are held and with the opportunities afforded for their investment. But though the interest may be considered to accumulate regularly year by year, yet the rules and tables for compound interest do not apply, owing to the addition of a fixed amount of new money to the total at the beginning of each period. Briefly stated, the problem of sinking-funds is, to find the amount of money which must be periodically set aside at a certain rate of interest, regularly compounded, to yield a certain sum in a given, length of time. In most practical cases the interest is compounded and the fresh amount added at the same time-usually once a year-and on this basis the problem may be solved as follows

Nov 1, 1909

By C. E. Reistle, G. L. Nye

The East Texas field is in Smith, Rusk, Gregg, Upshur and Cherokee counties, Texas. The discovery well was completed Sept. 8, 1930, near the eastern limit of the field. Within less than one year the new field became the dominant factor in the world production of crude oil. On Aug. 16, 1931, eleven months after completion of the discovery well, there were 1644 wells in the field, and the average daily production was 584,475 bbl. Since that time the number of wells has increased to 8195 on Oct. 1, 1933, and the field has produced 385,979,691 bbl. of oil. The geology of the East Texas field has been discussed by Lahee,1 Levorsen,2 Minor and Hanna3 and others, and it will not be discussed in detail here. The field is a structure of the monocline type on the westward dipping homocline between the Sabine uplift and the East Texas geosyncline. Production is obtained from the Woodbine group, which has been truncated and then sealed by the Austin chalk, which rests unconformably upon it. The oil-saturated part of the sand lies bettween a sub-sea depth of 3050 ft. on the east side of the field, where the Woodbine sand stops and the Austin chalk rests directly upon older formations, and a sub-sea depth of 3320 ft., which was the average depth of the water table in the sand at the time the field was discovered. The field is about 40 miles long and has an average width of approximately 4 1/2 miles. The area within the proven limits of the field is close to 116,580 acres and the normal Woodbine water underlies nearly 62,000 acres on the western side of the field at the present time. The field is unusual in several respects: (1) the tremendous size of the reservoir system and the quantity of oil in place; (2) the large area of the oil and water contact, which makes water movement possible into the oil-bearing part of the structure; (3) the absence of free gas within the main producing sand of the field. Changes in the reservoir pressure during the production history of the field have been greatly affected by

Jan 1, 1934

By AIME AIME

CORROSION of tanks, pipes and other equipment in the oil fields is becoming worse as the production of high- sulfur crudes in the Texas panhandle and west Texas areas increases. It has been estimated that .in certain fields of that State one tank out of every five has to be replaced every year because of the high sulfur content of the crude. One suggested method for combating tank corrosion is the use of .materials which have a high resistance to the corrosive action of hydrogen sulfide and high-sulfur crudes; aluminum is one of these materials. As a result, the United

Jan 1, 1929

By B. E. Lindsly

The withdrawal of gas and/or oil in appreciable quantity from a natural oil reservoir causes the pressure within the reservoir to diminish, and if the oil is completely saturated with gas, this dissolved gas begins to evolve from solution. The liberation of gas from solution in oil causes the oil to change in several ways, the principal changes being: (1) reduction in volume or "shrinkage"; (2) increase in specific gravity (decrease in degrees A.P.I.); (3) decrease of energy in the oil; (4) increased viscosity; (5) increased surface tension. As the writer's investigations have been concerned more with the first three items than with changes in viscosity and surface tension the following discussion relates particularly to the volumetric shrinkage of the oil, to the increased specific gravity, and to the decreased energy in the oil, each caused by the liberalion of dissolved gas. One of the most surprising facts that have developed in the study of high-pressure well-head and "bottom-hole" samples is the great reduction in volume that occurs in some oils when the naturally dissolved gas is liberated. High-pressure samples taken from well heads in the Oklahoma City, Kettleman Hills and Ventura, Calif., fields decreased in volume from 11.2 to 40.5 per cent when the dissolved gas was liberated in reducing the pressure on the sample to atmospheric. The amount of shrinkage an oil undergoes when gas is liberated depends upon the quantity of gas liberated and also upon its composition. A given volume of the heavier gases, propane and butane for example, will occupy more space in the oil than an equal volume of methane. The reason for this probably is that the molecules of the heavier gases are larger than those of the lighter gases. When gases are not in solution, and particularly when they are at low pressures, the distance between the gas molecules is so much greater than the dimensions of the molecules themselves that the mere size of the molecules has little effect upon the space occupied by the gas, Avogadro's hypothesis, which in effect states that all gases under the same conditions have the same number of molecules per unit volume, relates to this phenomenon. The fact that the heavier gases occupy more space than the lighter gases in the oil, and

Jan 1, 1934

By S. Arthur Krom

(New York Meeting, February, 1912.) THE James diagonal-plane slimer is specially adapted to handle the finest slimes, but it will also handle sands as coarse as 40-mesh. The saving efficiency of this machine is due to the original construction of the deck, and to the rapid reciprocating movement imparted to it by the head-motion. The deck consists of a plurality of connected planes, having a certain fixed ratio of inclination one to another. These planes intersect each other diagonally to the stroke-line of the table and are arranged so as to give the pulp on the table a double treatment. This double concentration performed by the diagonal-plane deck produces cleaner concentrates and tailings than those obtained by the operation of two separate machines. The action of the diagonal planes settles, combines, and holds all the concentrates in one compact mass, sharply defined from the gangue, and easily cut away without loss. Many slime-concentrating machines distribute the feed-pulp for a distance of 4 or 5 ft. only, and upon a very limited settling-surface. This results in a thick, heavy deposit, from which it is impossible to stratify the values and wash, away the gangue, the resulting products being dirty concentrates, and tailings carrying high values. The diagonal-plane slimer distributes the feed-pulp for a distance of 10 ft., and upon a settling-surface having an area of 40 sq. ft.; in other words, it spreads the pulp thinly on the table, which allows the metallic values to settle through the gangue quickly, forming a bottom stratum from which the thinly-distributed overlying stratum. of gangue is easily brushed away by the feed-water without disturbing the underlying concentrates. Referring to Fig. 1, plane A is the main settling-section, of the table. The feed pulp flows gently down this plane and is

Jun 1, 1912

By J. B. NEALEY

THE common method of shale mining, drilling, shooting and steam-shovel loading, is fast giving place to a comparatively new method which is purely mechanical. This machine is known as the shale planer and takes a cut from a very large face, 50 ft. or more in height. As shale deposits are usually stratified, the quality varying with the stratification, a very uniform product is obtained with this planer, for its "cut" is across the entire face, vertically. This planer was designed and built some 15 years ago by J. M. Powell, president of the Indiana Drain Tile Co., Brooklyn, Ind. Unevenness in mixing the material from the different layers in the shale deposit of this company was causing considerable fluctuation in the firing- shrinkage and color of the ware produced, thus lowering the quality. Some method of maintaining a uniform proportion was vital and this planer was therefore devised. Its capacity was approximately 175 tons daily: cut, mixed and loaded.

Jan 1, 1929

Joseph Hartshorne was born in Philadelphia in 1852. He died Aug. 23, 1918. After graduating from Haverford College, he took a special course in chemistry at the Massachusetts Institute of Technology, and later at the University of Pennsylvania. He started with The Pennsy!vania Steel Co. as an apprentice in 1873, working in the laboratory and mills for two years, and then one year as foreman in the Bessemer Department. Next, he was assistant chemist in the second Geological Survey of Pennsylvania. In 1878, he went to Prance to investigate the Pernot open-hearth furnace for the Cambria Iron Co. Upon his return, he assisted in designing and erecting the plant in Johnstown and was foreman of a turn for one year, and superintendent for the next. In 1881, he became superintendent of the Bessemer and rolling-mill departments. In 1884, he went to Pottstown and also made a trip to Europe to investigate the Bessemer basic process. Upon his return he dcsigned and erected the basic Bessemer plant for the Pottstown Iron Co., and was superintendent there until 1893, when the company failed. Since then he has been a consulting metallurgical engineer, and expert in patent cases. The !most important of the latter was that of Krupp versus Midvsle on the armor-plate patent case, in which he was leading cxpert for Midvale. He was a good linguist, having command of French and German, and a fair knowledge of Italian and Spanish. In all, he made eight professional trips to Europe.

Jan 1, 1920

NEARLY one hundred members of the Mining and Metallurgical Society of America and friends of Professor Peele met at dinner at the Aldine Club, New York, on the evening of April 26, to take part in the ceremonies attending the presentation of the Society's annual gold medal. This had been awarded to Professor Peele by the Society in recognition of his laborious and painstaking work as Editor-in-chief of the monu-mental "Mining Engi-neers' Handbook. Carl A. Meissner acted as toastmaster. W. Y. Westervelt, a student and lifelong asso-ciate of Professor Peele, then recounted some of his friend's early exploits, be-ginning with his mining adventures in the paternal cellar, whereby the neces-sity for adequate ventilation was indelibly impressed on his mind. Graduating from the Columbia School of Mines in 1883, Robert Peele for several years followed the typical mining career, as assayer and superinten-dentatan outlying Colorado mine; mill foreman and assistant superintendent of the Silver King, in Ari-zona; in charge of a mine at Fairplay, Colo.; and superintendent for the Ore-gon Gold Mines Co., at Cornucopia. At intervals during this experience, he spent parts of four years on two mineral investigations m in Peru, Bolivia, Colombia, and Dutch Guiana. He i was called to Columbia as Adjunct Professor of Mining in 1892, and became Professor in 1904. During his sabattical leave in 1903 he travelled around the world, r stopping at some of the most important mining cen-ters, and in 1910 he renewed his acquaintance with South Africa and South America.

Jan 6, 1923

B. S. and E. M. from the School of Mines at Socorro, New Mexico, in May, 1912. Immediately after graduating, he began as a practical miner in the U. S. mines at Bingham, Utah, but in November, 1912, he entered the operating department of the Chino Copper Co.'s concentrator at Hurley, New Mexico, where he stayed until July, 1913. During the latter half of 1913, he was employed as chemist in the laboratory of the El Paso smelter, at El Paso, Texas. In December, 1913, he became engineer and geologist with the Empire Zinc Co., at Socorro, New Mexico, which position he held at the time of his admission to the Institute in 1914, and until he entered the army in June, 1918. Before beginning the study of mining, Mr. Ringlund had completed a course in pharmacy, which accounts for his enlisting in the Medical Corps. Lieutenant George Roper, Jr. George Roper, Jr., a Junior Member of the Institute, was killed in an aeroplane accident near Shotwich, England, on Play 25, 1918. He was born at Steubenville, Ohio, in 1893, and at the time of his admi~sion to the Institute in 1916 was a student in mining and metallurgy at the Massachusetts Institute of Technology, Boston, Mass., from which he received the degree of S. B. in June, 1917. In August, 1917, he enlisted in the Royal Flying Corps, and after preliminary training on this side of the water, was sent to England. He was making the final cross-country flight of his course of training when the accident occurred.

Jan 1, 1920

S., at Niagara Falls, as an expert chemist. There he was engaged in perfect.ing the various kinds of gases, and while thus employed was gassed several times, which so affected his heart and lungs that he was unable to withstand an attack of the influenza which developed into pneumonia, from which he died at the end of 24 hours. He was a member of St. Luke's Episcopal Church, Lebanon, and belonged to the Ancient Accepted Scottish Rite of Freemasonry, Lebanon Lodge 121, I. 0. 0. F. and Camp 65, P. 0. S. of A. Lieutenant Bernhardt Edward Heine Bernhardt Edward Heine, a lieutenant in the Aviation Service of the U. S. Army, died as the result of a fa1I1 in an aeroplane at Fort Sill, Okla., on Aug. 10, 1918. The accident occurred on Aug. 2, when the machine in which he was flying with Lieutenant Carsons fell from a height of 1500 ft.; Lieutenant Carsons was instantly killed, but Lieutenant Heine died from his injuries a week later. Lieutenant Heine was born at Mount Clemens, Mich., in 1895. After attending the local High School he entered the Michigan College of Mines, and became a Junior Member of the Institute while still a student. He graduated in 1916, with the degree of B. S. In 1914 he served as a transitman for the engineering department of the City of Hancock, Mich. Lieutenant Heine had been in the army since 1916, having been with the 'troops at 'the Mexican border. He had been in the Aviation Section since August, 1917.

Jan 1, 1920